[PATCHv3 19/26] arm: mach-k3: do board config for PM and RM only if supported

[Vignesh Raghavendra <vigneshr@ti.com>]

On 5/5/21 11:25 PM, Tero Kristo wrote:
> From: Tero Kristo <t-kristo@ti.com>
> 
> If the raw PM support is built in, we are operating in the split
> firmware approach mode where RM and PM support is not available. In this
> case, skip the board config for these two.
> 
> Signed-off-by: Tero Kristo <t-kristo@ti.com>
> Signed-off-by: Tero Kristo <kristo@kernel.org>
> ---
>  arch/arm/mach-k3/sysfw-loader.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/arch/arm/mach-k3/sysfw-loader.c b/arch/arm/mach-k3/sysfw-loader.c
> index 0bacfc4d07..64472353c4 100644
> --- a/arch/arm/mach-k3/sysfw-loader.c
> +++ b/arch/arm/mach-k3/sysfw-loader.c
> @@ -159,11 +159,13 @@ static void k3_sysfw_configure_using_fit(void *fit,
>  		      ret);
>  
>  	/* Apply power/clock (PM) specific configuration to SYSFW */
> +#ifndef CONFIG_K3_DM_FW
>  	ret = board_ops->board_config_pm(ti_sci,
>  					 (u64)(u32)cfg_fragment_addr,
>  					 (u32)cfg_fragment_size);
>  	if (ret)
>  		panic("Failed to set board PM configuration (%d)\n", ret);
> +#endif
>  
>  	/* Extract resource management (RM) specific configuration from FIT */
>  	ret = fit_get_data_by_name(fit, images, SYSFW_CFG_RM,
> @@ -172,12 +174,14 @@ static void k3_sysfw_configure_using_fit(void *fit,
>  		panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_RM,
>  		      ret);
>  
> +#ifndef CONFIG_K3_DM_FW
>  	/* Apply resource management (RM) configuration to SYSFW */
>  	ret = board_ops->board_config_rm(ti_sci,
>  					 (u64)(u32)cfg_fragment_addr,
>  					 (u32)cfg_fragment_size);
>  	if (ret)
>  		panic("Failed to set board RM configuration (%d)\n", ret);
> +#endif
>  
>  	/* Extract security specific configuration from FIT */
>  	ret = fit_get_data_by_name(fit, images, SYSFW_CFG_SEC,
> 


We still need to send RM CFG to TIFS in case of J721e in order for DMA 
to work at R5 SPL. TIFS needs RM CFG to disable firewalls when R5 SPL 
sends  DMA channel cfg requests.

Could you squash the following diff for next version:

diff --git a/arch/arm/mach-k3/sysfw-loader.c b/arch/arm/mach-k3/sysfw-loader.c
index b95137fbdd..ac719cd46f 100644
--- a/arch/arm/mach-k3/sysfw-loader.c
+++ b/arch/arm/mach-k3/sysfw-loader.c
@@ -263,14 +263,7 @@ static void k3_sysfw_configure_using_fit(void *fit,
                panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_RM,
                      ret);
 
-#ifndef CONFIG_K3_DM_FW
-       /* Apply resource management (RM) configuration to SYSFW */
-       ret = board_ops->board_config_rm(ti_sci,
-                                        (u64)(u32)cfg_fragment_addr,
-                                        (u32)cfg_fragment_size);
-       if (ret)
-               panic("Failed to set board RM configuration (%d)\n", ret);
-#else
+#ifdef CONFIG_K3_DM_FW
        if (copy_bcfg) {
                desc = &bcfg_header->descs[1];
 
@@ -284,6 +277,13 @@ static void k3_sysfw_configure_using_fit(void *fit,
        }
 #endif
 
+       /* Apply resource management (RM) configuration to SYSFW */
+       ret = board_ops->board_config_rm(ti_sci,
+                                        (u64)(u32)cfg_fragment_addr,
+                                        (u32)cfg_fragment_size);
+       if (ret)
+               panic("Failed to set board RM configuration (%d)\n", ret);
+
        /* Extract security specific configuration from FIT */
        ret = fit_get_data_by_name(fit, images, SYSFW_CFG_SEC,
                                   &cfg_fragment_addr, &cfg_fragment_size);


Regards
Vignesh