From: Jeroen Hofstee <jeroen@myspectrum.nl>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 1/5] omap3: add useful dss defines
Date: Sun, 20 Jan 2013 22:42:08 +0100 [thread overview]
Message-ID: <50FC64B0.6060504@myspectrum.nl> (raw)
In-Reply-To: <1356246228-26732-2-git-send-email-nikita@compulab.co.il>
Hello Nikita,
On 12/23/2012 08:03 AM, Nikita Kiryanov wrote:
> Add useful omap3 dss defines for: polarity, TFT data lines, lcd
> display type, gfx burst size, and gfx format
>
> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
> ---
> arch/arm/include/asm/arch-omap3/dss.h | 35 +++++++++++++++++++++++++++++++++
> 1 file changed, 35 insertions(+)
>
> diff --git a/arch/arm/include/asm/arch-omap3/dss.h b/arch/arm/include/asm/arch-omap3/dss.h
> index ffaffbb..cb6d746 100644
> --- a/arch/arm/include/asm/arch-omap3/dss.h
> +++ b/arch/arm/include/asm/arch-omap3/dss.h
> @@ -167,6 +167,41 @@ struct venc_regs {
> #define VENC_OUT_SEL (1 << 6)
> #define DIG_LPP_SHIFT 16
>
> +/* LCD display type */
> +#define PASSIVE_DISPLAY 0
> +#define ACTIVE_DISPLAY 1
> +
> +/* TFTDATALINES */
> +#define LCD_INTERFACE_12_BIT 0
> +#define LCD_INTERFACE_16_BIT 1
> +#define LCD_INTERFACE_18_BIT 2
> +#define LCD_INTERFACE_24_BIT 3
> +
> +/* Polarity */
> +#define DSS_IVS (1 << 12)
> +#define DSS_IHS (1 << 13)
> +#define DSS_IPC (1 << 14)
> +#define DSS_IEO (1 << 15)
> +
> +/* GFX format */
> +#define GFXFORMAT_BITMAP1 0x0
> +#define GFXFORMAT_BITMAP2 0x1
> +#define GFXFORMAT_BITMAP4 0x2
> +#define GFXFORMAT_BITMAP8 0x3
> +#define GFXFORMAT_RGB12 0x4
> +#define GFXFORMAT_ARGB16 0x5
> +#define GFXFORMAT_RGB16 0x6
> +#define GFXFORMAT_RGB24_UNPACKED 0x8
> +#define GFXFORMAT_RGB24_PACKED 0x9
> +#define GFXFORMAT_ARGB32 0xC
> +#define GFXFORMAT_RGBA32 0xD
> +#define GFXFORMAT_RGBx32 0xE
> +
> +/* GFX burst size */
> +#define GFXBURSTSIZE4 0
> +#define GFXBURSTSIZE8 1
> +#define GFXBURSTSIZE16 2
> +
> /* Panel Configuration */
> struct panel_config {
> u32 timing_h;
most defines in omap dss use the location in the silicon itself.
For consistency you might want to shift these values to the
appropriate place. (or just use 32 mode so you can drop most
if not all of them)
Regards,
Jeroen
next prev parent reply other threads:[~2013-01-20 21:42 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-12-23 7:03 [U-Boot] [PATCH 0/5] Add splash screen for CM-T35 Nikita Kiryanov
2012-12-23 7:03 ` [U-Boot] [PATCH 1/5] omap3: add useful dss defines Nikita Kiryanov
2013-01-20 21:42 ` Jeroen Hofstee [this message]
2013-01-21 7:53 ` Nikita Kiryanov
2013-01-21 18:38 ` Jeroen Hofstee
2013-01-23 8:23 ` Nikita Kiryanov
2012-12-23 7:03 ` [U-Boot] [PATCH 2/5] lcd: add option for board specific splash screen preparation Nikita Kiryanov
2013-01-20 20:34 ` Jeroen Hofstee
2013-01-21 7:51 ` Nikita Kiryanov
2013-01-21 19:14 ` Jeroen Hofstee
2013-01-23 8:31 ` Nikita Kiryanov
2013-01-23 22:13 ` Jeroen Hofstee
2013-01-24 8:35 ` Igor Grinberg
2013-01-24 22:34 ` Jeroen Hofstee
2013-01-25 6:45 ` Igor Grinberg
2013-01-26 13:33 ` Jeroen Hofstee
2012-12-23 7:03 ` [U-Boot] [PATCH 3/5] cm-t35: add support for dvi displays Nikita Kiryanov
2013-01-20 20:59 ` Jeroen Hofstee
2013-01-21 8:12 ` Nikita Kiryanov
2013-01-23 21:39 ` Jeroen Hofstee
2013-01-24 9:02 ` Igor Grinberg
2012-12-23 7:03 ` [U-Boot] [PATCH 4/5] cm-t35: add support for user defined lcd parameters Nikita Kiryanov
2013-01-20 21:08 ` Jeroen Hofstee
2013-01-21 8:25 ` Nikita Kiryanov
2013-01-23 22:36 ` Jeroen Hofstee
2013-01-24 9:12 ` Igor Grinberg
2012-12-23 7:03 ` [U-Boot] [PATCH 5/5] cm-t35: add support for loading splash image from NAND Nikita Kiryanov
2012-12-24 8:55 ` Jeroen Hofstee
2012-12-25 8:56 ` Nikita Kiryanov
2012-12-26 14:27 ` Jeroen Hofstee
2012-12-30 14:39 ` Nikita Kiryanov
2013-01-22 7:37 ` Albert ARIBAUD
2013-01-23 10:47 ` Nikita Kiryanov
2013-01-23 11:07 ` Nikita Kiryanov
2013-03-26 14:51 ` [U-Boot] [U-Boot, " Tom Rini
2013-01-20 12:25 ` [U-Boot] [PATCH 0/5] Add splash screen for CM-T35 Nikita Kiryanov
2013-01-20 20:31 ` Jeroen Hofstee
2013-01-21 14:10 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=50FC64B0.6060504@myspectrum.nl \
--to=jeroen@myspectrum.nl \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.