From: Mark Jackson <mpfj-list@newflow.co.uk>
To: "linux-omap@vger.kernel.org" <linux-omap@vger.kernel.org>
Cc: martinez.javier@gmail.com, Tony Lindgren <tony@atomide.com>,
benoit.cousson@linaro.org
Subject: [PATCH v2] Add support for Newflow NanoBone board
Date: Sun, 11 Aug 2013 14:25:31 +0100 [thread overview]
Message-ID: <520790CB.2040905@newflow.co.uk> (raw)
NanoBone Specification:
-----------------------
CPU:
TI AM335x
Memory:
256MB DDR3
128MB NOR flash
128KB FRAM
Ethernet:
2 x 10/100 connected to SMSC LAN8710 PHY
USB:
1 x USB2.0 Type A
I2C:
2Kbit EEPROM (Microchip 24AA02)
RTC (Maxim DS1338)
GPIO Expander (Microchip MCP23017)
Expansion connector:
6 x UART
1 x MMC/SD
1 x USB2.0
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
---
Changes in v2:
- Reworked to use existing device nodes as suggested by Javier
MAINTAINERS | 6 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-nano.dts | 401 +++++++++++++++++++++++++++++++++++++
3 files changed, 408 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-nano.dts
diff --git a/MAINTAINERS b/MAINTAINERS
index 9705318..7549e99 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5998,6 +5998,12 @@ L: linux-omap@vger.kernel.org
S: Maintained
F: drivers/gpio/gpio-omap.c
+OMAP/NEWFLOW NANOBONE MACHINE SUPPORT
+M: Mark Jackson <mpfj@newflow.co.uk>
+L: linux-omap@vger.kernel.org
+S: Maintained
+F: arch/arm/boot/dts/am335x-nano.dts
+
OMFS FILESYSTEM
M: Bob Copeland <me@bobcopeland.com>
L: linux-karma-devel@lists.sourceforge.net
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 641b3c9..0d99a55 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -171,6 +171,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
am335x-evm.dtb \
am335x-evmsk.dtb \
am335x-bone.dtb \
+ am335x-nano.dtb \
am3517-evm.dtb \
am3517_mt_ventoux.dtb \
am43x-epos-evm.dtb
diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts
new file mode 100644
index 0000000..a8014ee
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-nano.dts
@@ -0,0 +1,401 @@
+/*
+ * Copyright (C) 2013 Newflow Ltd - http://www.newflow.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "Newflow AM335x NanoBone";
+ compatible = "ti,am33xx";
+
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&dcdc2_reg>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led@0 {
+ label = "nanobone:green:usr1";
+ gpios = <&gpio1 5 0>;
+ default-state = "off";
+ };
+ };
+};
+
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&misc_pins>;
+
+ misc_pins: misc_pins {
+ pinctrl-single,pins = <
+ 0x15c (PIN_OUTPUT | MUX_MODE7) /* spi0_cs0.gpio0_5 */
+ >;
+ };
+
+ gpmc_pins: gpmc_pins {
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+ 0x20 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad8.gpmc_ad8 */
+ 0x24 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad9.gpmc_ad9 */
+ 0x28 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad10.gpmc_ad10 */
+ 0x2c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad11.gpmc_ad11 */
+ 0x30 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad12.gpmc_ad12 */
+ 0x34 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad13.gpmc_ad13 */
+ 0x38 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad14.gpmc_ad14 */
+ 0x3c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad15.gpmc_ad15 */
+
+ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
+ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
+ 0x80 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn1.gpmc_csn1 */
+ 0x84 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn2.gpmc_csn2 */
+ 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn3.gpmc_csn3 */
+
+ 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
+ 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
+ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+ 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0_cle.gpmc_ben0_cle */
+
+ 0xa4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data1.gpmc_a1 */
+ 0xa8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data2.gpmc_a2 */
+ 0xac (PIN_OUTPUT | MUX_MODE1) /* lcd_data3.gpmc_a3 */
+ 0xb0 (PIN_OUTPUT | MUX_MODE1) /* lcd_data4.gpmc_a4 */
+ 0xb4 (PIN_OUTPUT | MUX_MODE1) /* lcd_data5.gpmc_a5 */
+ 0xb8 (PIN_OUTPUT | MUX_MODE1) /* lcd_data6.gpmc_a6 */
+ 0xbc (PIN_OUTPUT | MUX_MODE1) /* lcd_data7.gpmc_a7 */
+
+ 0xe0 (PIN_OUTPUT | MUX_MODE1) /* lcd_vsync.gpmc_a8 */
+ 0xe4 (PIN_OUTPUT | MUX_MODE1) /* lcd_hsync.gpmc_a9 */
+ 0xe8 (PIN_OUTPUT | MUX_MODE1) /* lcd_pclk.gpmc_a10 */
+ >;
+ };
+
+ i2c0_pins: i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+
+ uart0_pins: uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+ 0x174 (PIN_OUTPUT | MUX_MODE0) /* uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart1_pins: uart1_pins {
+ pinctrl-single,pins = <
+ 0x178 (PIN_OUTPUT | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */
+ 0x17c (PIN_OUTPUT | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */
+ 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ 0x184 (PIN_OUTPUT | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
+ uart2_pins: uart2_pins {
+ pinctrl-single,pins = <
+ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE7) /* lcd_data8.gpio2[14] */
+ 0xc4 (PIN_OUTPUT | MUX_MODE7) /* lcd_data9.gpio2[15] */
+ 0x150 (PIN_INPUT | MUX_MODE1) /* spi0_sclk.uart2_rxd */
+ 0x154 (PIN_OUTPUT | MUX_MODE1) /* spi0_d0.uart2_txd */
+ >;
+ };
+
+ uart3_pins: uart3_pins {
+ pinctrl-single,pins = <
+ 0xc8 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data10.uart3_ctsn */
+ 0xcc (PIN_OUTPUT | MUX_MODE6) /* lcd_data11.uart3_rtsn */
+ 0x160 (PIN_INPUT | MUX_MODE1) /* spi0_cs1.uart3_rxd */
+ 0x164 (PIN_OUTPUT | MUX_MODE1) /* ecap0_in_pwm0_out.uart3_txd */
+ >;
+ };
+
+ uart4_pins: uart4_pins {
+ pinctrl-single,pins = <
+ 0xd0 (PIN_INPUT_PULLUP | MUX_MODE6) /* lcd_data12.uart4_ctsn */
+ 0xd4 (PIN_OUTPUT | MUX_MODE6) /* lcd_data13.uart4_rtsn */
+ 0x168 (PIN_INPUT | MUX_MODE1) /* uart0_ctsn.uart4_rxd */
+ 0x16c (PIN_OUTPUT | MUX_MODE1) /* uart0_rtsn.uart4_txd */
+ >;
+ };
+
+ uart5_pins: uart5_pins {
+ pinctrl-single,pins = <
+ 0xd8 (PIN_INPUT | MUX_MODE4) /* lcd_data14.uart5_rxd */
+ 0x144 (PIN_OUTPUT | MUX_MODE3) /* rmiii1_refclk.uart5_txd */
+ >;
+ };
+
+ mmc1_pins: mmc1_pins {
+ pinctrl-single,pins = <
+ 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+ 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+ 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+ 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+ 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+ 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+ rts-gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rx-during-tx;
+ rs485-rts-delay = <1 1>;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+ rts-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+ rs485-rts-active-high;
+ rs485-rts-delay = <1 1>;
+ linux,rs485-enabled-at-boot-time;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5_pins>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ gpio@20 {
+ compatible = "mcp,mcp23017";
+ reg = <0x20>;
+ };
+
+ tps: tps@24 {
+ reg = <0x24>;
+ };
+
+ eeprom@53 {
+ compatible = "mcp,24c02";
+ reg = <0x53>;
+ pagesize = <8>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1307";
+ reg = <0x68>;
+ };
+};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ status = "okay";
+ gpmc,num-waitpins = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc_pins>;
+
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>; /* CS0: NOR 128M */
+
+ nor@0,0 {
+ reg = <0 0x00000000 0x08000000>;
+ compatible = "cfi-flash";
+ linux,mtd-name = "spansion,s29gl010p11t";
+ bank-width = <2>;
+
+ gpmc,mux-add-data = <2>;
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <160>;
+ gpmc,cs-wr-off-ns = <160>;
+ gpmc,adv-on-ns = <10>;
+ gpmc,adv-rd-off-ns = <30>;
+ gpmc,adv-wr-off-ns = <30>;
+ gpmc,oe-on-ns = <40>;
+ gpmc,oe-off-ns = <160>;
+ gpmc,we-on-ns = <40>;
+ gpmc,we-off-ns = <160>;
+ gpmc,rd-cycle-ns = <160>;
+ gpmc,wr-cycle-ns = <160>;
+ gpmc,access-ns = <150>;
+ gpmc,page-burst-access-ns = <10>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-delay-ns = <20>;
+ gpmc,wr-data-mux-bus-ns = <70>;
+ gpmc,wr-access-ns = <80>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ MTD partition table
+ ===================
+ +------------+-->0x00000000-> U-Boot start
+ | |
+ | |-->0x000BFFFF-> U-Boot end
+ | |-->0x000C0000-> ENV1 start
+ | |
+ | |-->0x000DFFFF-> ENV1 end
+ | |-->0x000E0000-> ENV2 start
+ | |
+ | |-->0x000FFFFF-> ENV2 end
+ | |-->0x00100000-> Kernel start
+ | |
+ | |-->0x004FFFFF-> Kernel end
+ | |-->0x00500000-> File system start
+ | |
+ | |-->0x014FFFFF-> File system end
+ | |-->0x01500000-> User data start
+ | |
+ | |-->0x03FFFFFF-> User data end
+ | |-->0x04000000-> Data storage start
+ | |
+ +------------+-->0x08000000-> NOR end (Free end)
+ */
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000c0000>; /* 768KB */
+ };
+
+ partition@1 {
+ label = "env1";
+ reg = <0x000c0000 0x00020000>; /* 128KB */
+ };
+
+ partition@2 {
+ label = "env2";
+ reg = <0x000e0000 0x00020000>; /* 128KB */
+ };
+
+ partition@3 {
+ label = "kernel";
+ reg = <0x00100000 0x00400000>; /* 4MB */
+ };
+
+ partition@4 {
+ label = "rootfs";
+ reg = <0x00500000 0x01000000>; /* 16MB */
+ };
+
+ partition@5 {
+ label = "user";
+ reg = <0x01500000 0x02b00000>; /* 43MB */
+ };
+
+ partition@6 {
+ label = "data";
+ reg = <0x04000000 0x04000000>; /* 64MB */
+ };
+ };
+};
+
+&mac {
+ dual_emac = <1>;
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <0>;
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ dual_emac_res_vlan = <2>;
+};
+
+#include "tps65217.dtsi"
+
+&tps {
+ regulators {
+ dcdc1_reg: regulator@0 {
+ regulator-always-on;
+ };
+
+ dcdc2_reg: regulator@1 {
+ /* VDD_MPU voltage limits 0.95V - 1.26V with ±4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1325000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc3_reg: regulator@2 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with ±4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: regulator@3 {
+ regulator-always-on;
+ };
+
+ ldo2_reg: regulator@4 {
+ regulator-always-on;
+ };
+
+ ldo3_reg: regulator@5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: regulator@6 {
+ regulator-always-on;
+ };
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next reply other threads:[~2013-08-11 13:25 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-11 13:25 Mark Jackson [this message]
2013-08-23 12:46 ` [PATCH v2] Add support for Newflow NanoBone board Mark Jackson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=520790CB.2040905@newflow.co.uk \
--to=mpfj-list@newflow.co.uk \
--cc=benoit.cousson@linaro.org \
--cc=linux-omap@vger.kernel.org \
--cc=martinez.javier@gmail.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.