* pata_sil680 regression 2.6.22->2.6.24
@ 2008-02-10 11:26 Robert Lowery
0 siblings, 0 replies; 3+ messages in thread
From: Robert Lowery @ 2008-02-10 11:26 UTC (permalink / raw)
To: linux-kernel
Hi Folks,
Having recently upgaded my Ubuntu install from Gutsy to Hardy, my 750GB
Seagate disk connected via a SiI680 PCI card is no longer detected. I
suspect this is caused by the MMIO changes in 2.6.24. Strangely in 2.6.22
the drive appears as sda1, but on 2.6.24 it appears as a non functioning
hde.
A working 2.6.22 based system reports
Feb 10 01:49:22 myth-backend kernel: [ 88.296373] sil680: BA5_EN = 1
clock = 00
Feb 10 01:49:22 myth-backend kernel: [ 88.296401] sil680: BA5_EN = 1
clock = 10
Feb 10 01:49:22 myth-backend kernel: [ 88.296479] sil680: 133MHz clock.
Feb 10 01:49:22 myth-backend kernel: [ 88.296672] ACPI: PCI Interrupt
0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
Feb 10 01:49:22 myth-backend kernel: [ 88.297584] scsi2 : pata_sil680
Feb 10 01:49:22 myth-backend kernel: [ 88.298142] scsi3 : pata_sil680
Feb 10 01:49:22 myth-backend kernel: [ 88.298398] ata1: PATA max
UDMA/133 cmd 0x00019000 ctl 0x00018802 bmdma 0x00017800 irq 19
Feb 10 01:49:22 myth-backend kernel: [ 88.298409] ata2: PATA max
UDMA/133 cmd 0x00018400 ctl 0x00018002 bmdma 0x00017808 irq 19
Feb 10 01:49:22 myth-backend kernel: [ 88.530102] ata1.00: ATA-7:
ST3750640A, 3.AAE, max UDMA/100
Feb 10 01:49:22 myth-backend kernel: [ 88.530139] ata1.00: 1465149168
sectors, multi 0: LBA48
Feb 10 01:49:22 myth-backend kernel: [ 88.604735] ata1.00: configured
for UDMA/100
A non working 2.6.24 based system reports
Feb 9 16:19:28 myth-backend kernel: [ 81.149973] SiI680: IDE controller
(0x1095:0x0680 rev 0x02) at PCI slot 0000:00:0d.0
Feb 9 16:19:28 myth-backend kernel: [ 81.150031] ACPI: PCI Interrupt
0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
Feb 9 16:19:28 myth-backend kernel: [ 81.150094] SiI680: BASE CLOCK == 133
Feb 9 16:19:28 myth-backend kernel: [ 81.150104] SiI680: 100% native
mode on irq 19
Feb 9 16:19:28 myth-backend kernel: [ 81.150121] ide2: MMIO-DMA ,
BIOS settings: hde:pio, hdf:pio
Feb 9 16:19:28 myth-backend kernel: [ 81.150145] ide3: MMIO-DMA ,
BIOS settings: hdg:pio, hdh:pio
Feb 9 16:19:28 myth-backend kernel: [ 82.113860] hde: þþÿþ`KÐ, ATA DISK
drive
Feb 9 16:19:28 myth-backend kernel: [ 82.114038] ide2 at
0xf882a080-0xf882a087,0xf882a08a on irq 19
Note, my bios does not support 750GB drives, so the drive is not
configured in the card BIOS. This has not stopped linux detecting it ok
in the past.
Please let me know if I need to provide any more information or additional
testing.
Thanks
-Rob
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: pata_sil680 regression 2.6.22->2.6.24
2008-02-10 18:12 ` Robert Hancock
@ 2008-02-10 21:44 ` Robert Lowery
0 siblings, 0 replies; 3+ messages in thread
From: Robert Lowery @ 2008-02-10 21:44 UTC (permalink / raw)
To: Robert Hancock; +Cc: linux-kernel
> Robert Lowery wrote:
>> Hi Folks,
>>
>> Having recently upgaded my Ubuntu install from Gutsy to Hardy, my 750GB
>> Seagate disk connected via a SiI680 PCI card is no longer detected. I
>> suspect this is caused by the MMIO changes in 2.6.24. Strangely in
>> 2.6.22
>> the drive appears as sda1, but on 2.6.24 it appears as a non functioning
>> hde.
>>
>> A working 2.6.22 based system reports
>>
>> Feb 10 01:49:22 myth-backend kernel: [ 88.296373] sil680: BA5_EN = 1
>> clock = 00
>> Feb 10 01:49:22 myth-backend kernel: [ 88.296401] sil680: BA5_EN = 1
>> clock = 10
>> Feb 10 01:49:22 myth-backend kernel: [ 88.296479] sil680: 133MHz
>> clock.
>> Feb 10 01:49:22 myth-backend kernel: [ 88.296672] ACPI: PCI Interrupt
>> 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
>> Feb 10 01:49:22 myth-backend kernel: [ 88.297584] scsi2 : pata_sil680
>> Feb 10 01:49:22 myth-backend kernel: [ 88.298142] scsi3 : pata_sil680
>> Feb 10 01:49:22 myth-backend kernel: [ 88.298398] ata1: PATA max
>> UDMA/133 cmd 0x00019000 ctl 0x00018802 bmdma 0x00017800 irq 19
>> Feb 10 01:49:22 myth-backend kernel: [ 88.298409] ata2: PATA max
>> UDMA/133 cmd 0x00018400 ctl 0x00018002 bmdma 0x00017808 irq 19
>> Feb 10 01:49:22 myth-backend kernel: [ 88.530102] ata1.00: ATA-7:
>> ST3750640A, 3.AAE, max UDMA/100
>> Feb 10 01:49:22 myth-backend kernel: [ 88.530139] ata1.00: 1465149168
>> sectors, multi 0: LBA48
>> Feb 10 01:49:22 myth-backend kernel: [ 88.604735] ata1.00: configured
>> for UDMA/100
>>
>> A non working 2.6.24 based system reports
>>
>> Feb 9 16:19:28 myth-backend kernel: [ 81.149973] SiI680: IDE
>> controller
>> (0x1095:0x0680 rev 0x02) at PCI slot 0000:00:0d.0
>> Feb 9 16:19:28 myth-backend kernel: [ 81.150031] ACPI: PCI Interrupt
>> 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
>> Feb 9 16:19:28 myth-backend kernel: [ 81.150094] SiI680: BASE CLOCK
>> == 133
>> Feb 9 16:19:28 myth-backend kernel: [ 81.150104] SiI680: 100% native
>> mode on irq 19
>> Feb 9 16:19:28 myth-backend kernel: [ 81.150121] ide2: MMIO-DMA ,
>> BIOS settings: hde:pio, hdf:pio
>> Feb 9 16:19:28 myth-backend kernel: [ 81.150145] ide3: MMIO-DMA ,
>> BIOS settings: hdg:pio, hdh:pio
>> Feb 9 16:19:28 myth-backend kernel: [ 82.113860] hde: þþÿþ`KÐ, ATA
>> DISK
>> drive
>> Feb 9 16:19:28 myth-backend kernel: [ 82.114038] ide2 at
>> 0xf882a080-0xf882a087,0xf882a08a on irq 19
>
> This is not pata_sil680, this is drivers/ide trying to operate this
> card. Has something changed in your kernel config?
Hi Robert,
Thanks for your reply. I'm not sure if the kernel config has changed as I
am using the stock ubuntu kernels. Perhaps I should log a bug with
ubuntu. If it helps, the pata_sil680 module is loaded (visible in
/proc/modules) when I boot either kernel, it just doesn't detect my 750GB
drive in the 2.6.24 based kernel.
>
>>
>> Note, my bios does not support 750GB drives, so the drive is not
>> configured in the card BIOS. This has not stopped linux detecting it ok
>> in the past.
>>
>> Please let me know if I need to provide any more information or
>> additional
>> testing.
>>
>> Thanks
>>
>> -Rob
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-kernel"
>> in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: pata_sil680 regression 2.6.22->2.6.24
[not found] <fa.VTsuPmDh8g6L8kkfHY3j5Qvl65c@ifi.uio.no>
@ 2008-02-10 18:12 ` Robert Hancock
2008-02-10 21:44 ` Robert Lowery
0 siblings, 1 reply; 3+ messages in thread
From: Robert Hancock @ 2008-02-10 18:12 UTC (permalink / raw)
To: Robert Lowery; +Cc: linux-kernel
Robert Lowery wrote:
> Hi Folks,
>
> Having recently upgaded my Ubuntu install from Gutsy to Hardy, my 750GB
> Seagate disk connected via a SiI680 PCI card is no longer detected. I
> suspect this is caused by the MMIO changes in 2.6.24. Strangely in 2.6.22
> the drive appears as sda1, but on 2.6.24 it appears as a non functioning
> hde.
>
> A working 2.6.22 based system reports
>
> Feb 10 01:49:22 myth-backend kernel: [ 88.296373] sil680: BA5_EN = 1
> clock = 00
> Feb 10 01:49:22 myth-backend kernel: [ 88.296401] sil680: BA5_EN = 1
> clock = 10
> Feb 10 01:49:22 myth-backend kernel: [ 88.296479] sil680: 133MHz clock.
> Feb 10 01:49:22 myth-backend kernel: [ 88.296672] ACPI: PCI Interrupt
> 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
> Feb 10 01:49:22 myth-backend kernel: [ 88.297584] scsi2 : pata_sil680
> Feb 10 01:49:22 myth-backend kernel: [ 88.298142] scsi3 : pata_sil680
> Feb 10 01:49:22 myth-backend kernel: [ 88.298398] ata1: PATA max
> UDMA/133 cmd 0x00019000 ctl 0x00018802 bmdma 0x00017800 irq 19
> Feb 10 01:49:22 myth-backend kernel: [ 88.298409] ata2: PATA max
> UDMA/133 cmd 0x00018400 ctl 0x00018002 bmdma 0x00017808 irq 19
> Feb 10 01:49:22 myth-backend kernel: [ 88.530102] ata1.00: ATA-7:
> ST3750640A, 3.AAE, max UDMA/100
> Feb 10 01:49:22 myth-backend kernel: [ 88.530139] ata1.00: 1465149168
> sectors, multi 0: LBA48
> Feb 10 01:49:22 myth-backend kernel: [ 88.604735] ata1.00: configured
> for UDMA/100
>
> A non working 2.6.24 based system reports
>
> Feb 9 16:19:28 myth-backend kernel: [ 81.149973] SiI680: IDE controller
> (0x1095:0x0680 rev 0x02) at PCI slot 0000:00:0d.0
> Feb 9 16:19:28 myth-backend kernel: [ 81.150031] ACPI: PCI Interrupt
> 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 19
> Feb 9 16:19:28 myth-backend kernel: [ 81.150094] SiI680: BASE CLOCK == 133
> Feb 9 16:19:28 myth-backend kernel: [ 81.150104] SiI680: 100% native
> mode on irq 19
> Feb 9 16:19:28 myth-backend kernel: [ 81.150121] ide2: MMIO-DMA ,
> BIOS settings: hde:pio, hdf:pio
> Feb 9 16:19:28 myth-backend kernel: [ 81.150145] ide3: MMIO-DMA ,
> BIOS settings: hdg:pio, hdh:pio
> Feb 9 16:19:28 myth-backend kernel: [ 82.113860] hde: þþÿþ`KÐ, ATA DISK
> drive
> Feb 9 16:19:28 myth-backend kernel: [ 82.114038] ide2 at
> 0xf882a080-0xf882a087,0xf882a08a on irq 19
This is not pata_sil680, this is drivers/ide trying to operate this
card. Has something changed in your kernel config?
>
> Note, my bios does not support 750GB drives, so the drive is not
> configured in the card BIOS. This has not stopped linux detecting it ok
> in the past.
>
> Please let me know if I need to provide any more information or additional
> testing.
>
> Thanks
>
> -Rob
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2008-02-10 21:45 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-02-10 11:26 pata_sil680 regression 2.6.22->2.6.24 Robert Lowery
[not found] <fa.VTsuPmDh8g6L8kkfHY3j5Qvl65c@ifi.uio.no>
2008-02-10 18:12 ` Robert Hancock
2008-02-10 21:44 ` Robert Lowery
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.