* [PATCH V2] ARM: bcm2835: node name unit address cleanup
@ 2014-02-14 6:04 Stephen Warren
2014-02-15 6:33 ` Stephen Warren
0 siblings, 1 reply; 2+ messages in thread
From: Stephen Warren @ 2014-02-14 6:04 UTC (permalink / raw)
To: linux-arm-kernel
DT nodes that contain a reg property should include a unit address in
their name. Add the missing unit addresses.
The unit address in a node name must match the value in the reg property.
Fix the cases where they don't match.
Don't fix the /clocks/* node names yet; that causes problems the clock
driver to attempt to register multiple clocks with the same name, which
fails.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
---
v2:
* Fix existing mismatching unit addresses.
* Don't touch the /clocks/* nodes.
---
arch/arm/boot/dts/bcm2835.dtsi | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
index 5ceba45..a2d4889 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/bcm2835.dtsi
@@ -15,7 +15,7 @@
#size-cells = <1>;
ranges = <0x7e000000 0x20000000 0x02000000>;
- timer {
+ timer at 7e003000 {
compatible = "brcm,bcm2835-system-timer";
reg = <0x7e003000 0x1000>;
interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
@@ -43,24 +43,24 @@
brcm,dma-channel-mask = <0x7f35>;
};
- intc: interrupt-controller {
+ intc: interrupt-controller at 7e00b200 {
compatible = "brcm,bcm2835-armctrl-ic";
reg = <0x7e00b200 0x200>;
interrupt-controller;
#interrupt-cells = <2>;
};
- watchdog {
+ watchdog at 7e100000 {
compatible = "brcm,bcm2835-pm-wdt";
reg = <0x7e100000 0x28>;
};
- rng {
+ rng at 7e104000 {
compatible = "brcm,bcm2835-rng";
reg = <0x7e104000 0x10>;
};
- gpio: gpio {
+ gpio: gpio at 7e200000 {
compatible = "brcm,bcm2835-gpio";
reg = <0x7e200000 0xb4>;
/*
@@ -83,7 +83,7 @@
#interrupt-cells = <2>;
};
- uart at 20201000 {
+ uart at 7e201000 {
compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
reg = <0x7e201000 0x1000>;
interrupts = <2 25>;
@@ -101,7 +101,7 @@
dma-names = "tx", "rx";
};
- spi: spi at 20204000 {
+ spi: spi at 7e204000 {
compatible = "brcm,bcm2835-spi";
reg = <0x7e204000 0x1000>;
interrupts = <2 22>;
@@ -121,7 +121,7 @@
status = "disabled";
};
- sdhci: sdhci {
+ sdhci: sdhci at 7e300000 {
compatible = "brcm,bcm2835-sdhci";
reg = <0x7e300000 0x100>;
interrupts = <2 30>;
@@ -129,7 +129,7 @@
status = "disabled";
};
- i2c1: i2c at 20804000 {
+ i2c1: i2c at 7e804000 {
compatible = "brcm,bcm2835-i2c";
reg = <0x7e804000 0x1000>;
interrupts = <2 21>;
@@ -139,7 +139,7 @@
status = "disabled";
};
- usb {
+ usb at 7e980000 {
compatible = "brcm,bcm2835-usb";
reg = <0x7e980000 0x10000>;
interrupts = <1 9>;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [PATCH V2] ARM: bcm2835: node name unit address cleanup
2014-02-14 6:04 [PATCH V2] ARM: bcm2835: node name unit address cleanup Stephen Warren
@ 2014-02-15 6:33 ` Stephen Warren
0 siblings, 0 replies; 2+ messages in thread
From: Stephen Warren @ 2014-02-15 6:33 UTC (permalink / raw)
To: linux-arm-kernel
On 02/13/2014 11:04 PM, Stephen Warren wrote:
> DT nodes that contain a reg property should include a unit address in
> their name. Add the missing unit addresses.
>
> The unit address in a node name must match the value in the reg property.
> Fix the cases where they don't match.
>
> Don't fix the /clocks/* node names yet; that causes problems the clock
> driver to attempt to register multiple clocks with the same name, which
> fails.
I've applied this to bcm2835's for-3.15/dt branch.
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2014-02-15 6:33 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-02-14 6:04 [PATCH V2] ARM: bcm2835: node name unit address cleanup Stephen Warren
2014-02-15 6:33 ` Stephen Warren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.