[U-Boot] [PULL] Please pull u-boot-imx

[Stefano Babic <sbabic@denx.de>]

Hi Tom,

please pull from u-boot-imx, thanks !

The following changes since commit f33cdaa4c3da4a8fd35aa2f9a3172f31cc887b35:

  Prepare v2015.04 (2015-04-13 10:53:03 -0400)

are available in the git repository at:

  git://www.denx.de/git/u-boot-imx.git master

for you to fetch changes up to 205d58699b157df75f1aa0b363ea9c21add21a0c:

  mx6cuboxi: Load the correct 'fdtfile' variable (2015-04-27 13:13:58 +0200)

----------------------------------------------------------------
Eric Nelson (1):
      nitrogen6x: allow gzipped bitmap display

Fabio Estevam (9):
      mx6: Add initial SPL support for HummingBoard-i2eX
      mx6sabresd: Fix SPL memory description
      mx6sabresd: Remove uneeded ifdef
      mx6cuboxi: Fix the defconfig name
      mx6cuboxi: Prepare for multi SoC support
      mx6cuboxi: Introduce multi-SoC support
      mx6cuboxi: Differentiate Cubox-i and Hummingboard
      mx6cuboxi: Use more standard namings for fdt variables
      mx6cuboxi: Load the correct 'fdtfile' variable

J?rg Krause (1):
      ARM: mxs: Get boot mode from OCRAM

Pushpal Sidhu (3):
      imx: ventana: add DT fixup for GW522x to change PCIE_RST# GPIO
      imx: ventana: Add new memory configuration
      imx: ventana: Update missing memory/calib handling

Stefan Roese (1):
      arm: mx6: tqma6: Extract baseboard configs into separate config file

Tim Harvey (34):
      arm: mx6: ddr: add pd_fast_exit flag to system information
      fdt: add new fdt_fixup_display function to configure display
      imx: ventana: disable 4k tftp/nfs packets
      imx: ventana: add i210 support
      imx: ventana: assign default ethprime dynamically
      imx: ventana: remove unused GPIO configuration
      imx: ventana: add usb_pcisel hwconfig support
      imx: ventana: enable precharge power-down fast-exit mode
      imx: ventana: add support for 4Gb density mem devices with IMX6DL
      imx: ventana: set LTC3676 PMIC to appropriate values per datasheet
      imx: ventana: config: add USB Mass Storage (ums) support
      imx: ventana: config: Support ramdisk
      imx: ventana: config: enable edid support
      imx: ventana: config: enable EXT4 filesystem read/write support
      imx: ventana: fix various sparse warnings
      imx: ventana: disable IMX6 watchdogs on GW51xx RevA and RevB
      imx: ventana: Add support for GW551x
      imx: ventana: add usb_pgood_delay 2sec default
      imx: ventana: add wdis config for GW5520
      imx: ventana: only pinmux FEC enet signals for boards using it
      imx: ventana: update boot scripts to support ubifs boot vol
      imx: ventana: remove GSC hwmon voltage rail min/max test
      imx: ventana: add mem_mb dynamic env var
      imx: ventana: gsc: add new hwmon rails
      imx: ventana: added DT fixup for GW551x-A video input
      imx: ventana: updated 16bit DDR calibration
      imx: ventana: remove 128x16 calibration (share with 128x32)
      imx: ventana: add DT fixup for GW54xx compatibility with older kernels
      imx: ventana: add support for DLC-700JMGT4 and DLC-800FIGT3 LCD
displays
      imx: ventana: added device-tree display configuration for LVDS
displays
      imx: ventana: add 'gsc wd' command for enabling and disabling GSC
watchdog
      imx: ventana: use hdmiinfmt env var to override HDMI capture format
      imx: ventana: set HDMI video in to yuv422bt656 for GW551x-A
      power: pfuze100: fix LDO_EN bit value

gaurav rana (1):
      iMX: Fix compilation error when enabling SECURE_BOOT

 arch/arm/Kconfig                            |   6 ++
 arch/arm/cpu/arm926ejs/mxs/spl_boot.c       |  29 ++--------
 arch/arm/cpu/armv7/mx6/ddr.c                |   7 ++-
 arch/arm/include/asm/arch-mx6/mx6-ddr.h     |   1 +
 board/freescale/common/Makefile             |   3 +-
 board/freescale/mx6sabresd/mx6sabresd.c     |  13 ++---
 board/gateworks/gw_ventana/eeprom.c         |  10 +++-
 board/gateworks/gw_ventana/gsc.c            | 130
+++++++++++++++++++++++++++++------------
 board/gateworks/gw_ventana/gsc.h            |  10 +++-
 board/gateworks/gw_ventana/gw_ventana.c     | 367
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++--------------------
 board/gateworks/gw_ventana/gw_ventana_spl.c | 129
++++++++++++++++++++++++++++++++++++-----
 board/gateworks/gw_ventana/ventana_eeprom.h |   1 +
 board/solidrun/mx6cuboxi/Kconfig            |  15 +++++
 board/solidrun/mx6cuboxi/MAINTAINERS        |   6 ++
 board/solidrun/mx6cuboxi/Makefile           |   9 +++
 board/solidrun/mx6cuboxi/README             |  21 +++++++
 board/solidrun/mx6cuboxi/mx6cuboxi.c        | 510
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 common/fdt_support.c                        |  29 ++++++++++
 configs/mx6cuboxi_defconfig                 |   6 ++
 include/configs/gw_ventana.h                |  68 ++++++++++++++--------
 include/configs/mx6cuboxi.h                 | 218
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 include/configs/nitrogen6x.h                |   3 +
 include/configs/tqma6.h                     |  57 ++++++------------
 include/configs/tqma6_mba6.h                |  30 ++++++++++
 include/fdt_support.h                       |  13 +++++
 include/power/pfuze100_pmic.h               |   2 +-
 26 files changed, 1480 insertions(+), 213 deletions(-)
 create mode 100644 board/solidrun/mx6cuboxi/Kconfig
 create mode 100644 board/solidrun/mx6cuboxi/MAINTAINERS
 create mode 100644 board/solidrun/mx6cuboxi/Makefile
 create mode 100644 board/solidrun/mx6cuboxi/README
 create mode 100644 board/solidrun/mx6cuboxi/mx6cuboxi.c
 create mode 100644 configs/mx6cuboxi_defconfig
 create mode 100644 include/configs/mx6cuboxi.h
 create mode 100644 include/configs/tqma6_mba6.h

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================