From mboxrd@z Thu Jan 1 00:00:00 1970 From: Heiko Schocher Date: Mon, 30 May 2016 12:15:56 +0200 Subject: [U-Boot] [PATCH v1 6/7] dfu, nand, ubi: fix erasing after write finish In-Reply-To: <20160530115157.52d49e92@amdc2363> References: <1464152832-11200-1-git-send-email-hs@denx.de> <1464152832-11200-7-git-send-email-hs@denx.de> <57454485.1080601@denx.de> <20160530115157.52d49e92@amdc2363> Message-ID: <574C12DC.90509@denx.de> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hello Lukasz, Am 30.05.2016 um 11:51 schrieb Lukasz Majewski: > Hi Heiko, > >> Hello Scott, >> >> Am 25.05.2016 um 07:33 schrieb Scott Wood: >>> On 05/25/2016 12:07 AM, Heiko Schocher wrote: >>>> writting to ubi nand partitions need after write ends an erase >>>> of the remaining sectors. This fail, if dfu write size was not >>>> a multiple of erasesize, example log: >>>> >>>> Failure erase: -1 > > Is this a new bug? Or is this a regression? This is a fix of a current Bug. >>>> Fix this error. >>>> >>>> Signed-off-by: Heiko Schocher >>> >>> Why don't you just erase the whole partition up front? >> >> Good question ... I think the reason is that if we erase a big >> partition at once on dfu start, dfu-util rans into timeout ... but >> may I am wrong ... > > This is interesting, since we had similar problem with eMMC, but on the > end of writing large files to FS. > > To fix this issue, the deferred write has been introduced [1]: > SHA1: fc18f8d170ecc7e15269ad5312ec643addb42491 I had downloaded files > 300MiB IIRC without problems on NAND. >> IIRC at the end of a DFU transfer DFU protocol sends a "flush" to the >> device ... > > Yes, correct, we do that. > >> where we currently erase the remaining sectors > > I'm not the "regular" user of NAND part of DFU framework. However, > AFAIK each sector is erased just before writing (dfu_nand.c @ line 62). Yep, and this is currrent state and works fine (on the siemens boards) And so we need at the end in the flush state of the dfu protcol to erase the sectors on the end of the partition, if it is an ubi partition. > The same scheme should be performed just before writing last chunk of > data to NAND. > >> ... we need >> this on an ubi partition, else there may remain old used UBI >> sectors ... (BTW: we need an "ubi format" command ...) >> >> @Lukasz? Am I correct? Or could we simple erase before writting? > > I'm just wondering if have you tried erasing the whole NAND area before > starting DFU operation? > How long does it take to erase large NAND area for e.g. rootfs? I must measure this value ... but just posted the etamin module support, and there is a DDP Nand with 4GiB ... and there is a big fat (UBI) partition at the end: device nand2 , # parts = 9 #: name size offset mask_flags [...] 8: rootfs 0xff080000 0x00f80000 0 > If I remember correctly, the timeout in dfu-util is 5 seconds sharp. Yes, this is may too small, right, just erased the DDP nand on the etamin module: U-Boot# nand device 0 Device 0: nand0... is now current device U-Boot# time nand erase f80000 7f080000 NAND erase: device 0 offset 0xf80000, size 0x7f080000 [...] Erasing at 0x7ff80000 -- 100% complete. OK time: 3.999 seconds U-Boot# nand device 1 Device 1: nand1... is now current device U-Boot# time nand erase.chip NAND erase.chip: device 1 whole chip [...] Erasing at 0x7ff80000 -- 100% complete. OK time: 4.019 seconds U-Boot# ~8seconds for erasing the hole partition ... > Generally, I'm fine with erasing NAND sectors just before writing (as > we do it up till now in the NAND part of DFU). Thanks for clarification! bye, Heiko -- DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany