Re: [PATCH v2 05/21] cpufreq: amd: introduce a new amd pstate driver to support future processors

["Fontenot, Nathan" <Nathan.Fontenot@amd.com>]

On 9/26/2021 4:05 AM, Huang Rui wrote:
> amd-pstate is the AMD CPU performance scaling driver that introduces a
> new CPU frequency control mechanism on AMD Zen based CPU series in Linux
> kernel. The new mechanism is based on Collaborative processor
> performance control (CPPC) which is finer grain frequency management
> than legacy ACPI hardware P-States. Current AMD CPU platforms are using
> the ACPI P-states driver to manage CPU frequency and clocks with
> switching only in 3 P-states. AMD P-States is to replace the ACPI
> P-states controls, allows a flexible, low-latency interface for the
> Linux kernel to directly communicate the performance hints to hardware.
> 
> "amd-pstate" leverages the Linux kernel governors such as *schedutil*,
> *ondemand*, etc. to manage the performance hints which are provided by CPPC
> hardware functionality. The first version for amd-pstate is to support one
> of the Zen3 processors, and we will support more in future after we verify
> the hardware and SBIOS functionalities.
> 
> There are two types of hardware implementations for amd-pstate: one is full
> MSR support and another is shared memory support. It can use
> X86_FEATURE_AMD_CPPC_EXT feature flag to distinguish the different types.
> 
> Using the new AMD P-States method + kernel governors (*schedutil*,
> *ondemand*, ...) to manage the frequency update is the most appropriate
> bridge between AMD Zen based hardware processor and Linux kernel, the
> processor is able to ajust to the most efficiency frequency according to
> the kernel scheduler loading.
> 
> Performance Per Watt (PPW) Caculation:
> 
> The PPW caculation is referred by below paper:
> https://software.intel.com/content/dam/develop/external/us/en/documents/performance-per-what-paper.pdf
> 
> Below formula is referred from below spec to measure the PPW:
> 
> (F / t) / P = F * t / (t * E) = F / E,
> 
> "F" is the number of frames per second.
> "P" is power measurd in watts.
> "E" is energy measured in joules.
> 
> We use the RAPL interface with "perf" tool to get the energy data of the
> package power.
> 
> The data comparsions between amd-pstate and acpi-freq module are tested on
> AMD Cezanne processor:
> 
> 1) TBench CPU benchmark:
> 
> +---------------------------------------------------------------------+
> |                                                                     |
> |               TBench (Performance Per Watt)                         |
> |                                                    Higher is better |
> +-------------------+------------------------+------------------------+
> |                   |  Performance Per Watt  |  Performance Per Watt  |
> |   Kernel Module   |       (Schedutil)      |       (Ondemand)       |
> |                   |  Unit: MB / (s * J)    |  Unit: MB / (s * J)    |
> +-------------------+------------------------+------------------------+
> |                   |                        |                        |
> |    acpi-cpufreq   |         3.022          |        2.969           |
> |                   |                        |                        |
> +-------------------+------------------------+------------------------+
> |                   |                        |                        |
> |     amd-pstate    |         3.131          |        3.284           |
> |                   |                        |                        |
> +-------------------+------------------------+------------------------+
> 
> 2) Gitsource CPU benchmark:
> 
> +---------------------------------------------------------------------+
> |                                                                     |
> |               Gitsource (Performance Per Watt)                      |
> |                                                    Higher is better |
> +-------------------+------------------------+------------------------+
> |                   |  Performance Per Watt  |  Performance Per Watt  |
> |   Kernel Module   |       (Schedutil)      |       (Ondemand)       |
> |                   |  Unit: 1 / (s * J)     |  Unit: 1 / (s * J)     |
> +-------------------+------------------------+------------------------+
> |                   |                        |                        |
> |    acpi-cpufreq   |     3.42172E-07        |     2.74508E-07        |
> |                   |                        |                        |
> +-------------------+------------------------+------------------------+
> |                   |                        |                        |
> |     amd-pstate    |     4.09141E-07        |     3.47610E-07        |
> |                   |                        |                        |
> +-------------------+------------------------+------------------------+
> 
> 3) Speedometer 2.0 CPU benchmark:
> 
> +---------------------------------------------------------------------+
> |                                                                     |
> |               Speedometer 2.0 (Performance Per Watt)                |
> |                                                    Higher is better |
> +-------------------+------------------------+------------------------+
> |                   |  Performance Per Watt  |  Performance Per Watt  |
> |   Kernel Module   |       (Schedutil)      |       (Ondemand)       |
> |                   |  Unit: 1 / (s * J)     |  Unit: 1 / (s * J)     |
> +-------------------+------------------------+------------------------+
> |                   |                        |                        |
> |    acpi-cpufreq   |      0.116111767       |      0.110321664       |
> |                   |                        |                        |
> +-------------------+------------------------+------------------------+
> |                   |                        |                        |
> |     amd-pstate    |      0.115825281       |      0.122024299       |
> |                   |                        |                        |
> +-------------------+------------------------+------------------------+
> 
> According to above average data, we can see this solution has shown better
> performance per watt scaling on mobile CPU benchmarks in most of cases.
> 
> Signed-off-by: Huang Rui <ray.huang@amd.com>
> ---
>  drivers/cpufreq/Kconfig.x86  |  13 +
>  drivers/cpufreq/Makefile     |   1 +
>  drivers/cpufreq/amd-pstate.c | 446 +++++++++++++++++++++++++++++++++++
>  3 files changed, 460 insertions(+)
>  create mode 100644 drivers/cpufreq/amd-pstate.c
> 
> diff --git a/drivers/cpufreq/Kconfig.x86 b/drivers/cpufreq/Kconfig.x86
> index 92701a18bdd9..9cd7e338bdcd 100644
> --- a/drivers/cpufreq/Kconfig.x86
> +++ b/drivers/cpufreq/Kconfig.x86
> @@ -34,6 +34,19 @@ config X86_PCC_CPUFREQ
>  
>  	  If in doubt, say N.
>  
> +config X86_AMD_PSTATE
> +	tristate "AMD Processor P-State driver"
> +	depends on X86
> +	select ACPI_PROCESSOR if ACPI
> +	select ACPI_CPPC_LIB if X86_64 && ACPI && SCHED_MC_PRIO
> +	select CPU_FREQ_GOV_SCHEDUTIL if SMP
> +	help
> +	  This driver adds a CPUFreq driver which utilizes a fine grain
> +	  processor performance freqency control range instead of legacy
> +	  performance levels. This driver also supports newer AMD CPUs.

Go ahead and call out that this is a CPPC driver in the help message, that
is what the driver is.

The reference to "also supports newer AMD CPUs" seems vague, can you elaborate?

> +
> +	  If in doubt, say N.
> +
>  config X86_ACPI_CPUFREQ
>  	tristate "ACPI Processor P-States driver"
>  	depends on ACPI_PROCESSOR
> diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
> index 27d3bd7ea9d4..5c9a2a1ee8dc 100644
> --- a/drivers/cpufreq/Makefile
> +++ b/drivers/cpufreq/Makefile
> @@ -25,6 +25,7 @@ obj-$(CONFIG_CPUFREQ_DT_PLATDEV)	+= cpufreq-dt-platdev.o
>  # speedstep-* is preferred over p4-clockmod.
>  
>  obj-$(CONFIG_X86_ACPI_CPUFREQ)		+= acpi-cpufreq.o
> +obj-$(CONFIG_X86_AMD_PSTATE)		+= amd-pstate.o
>  obj-$(CONFIG_X86_POWERNOW_K8)		+= powernow-k8.o
>  obj-$(CONFIG_X86_PCC_CPUFREQ)		+= pcc-cpufreq.o
>  obj-$(CONFIG_X86_POWERNOW_K6)		+= powernow-k6.o
> diff --git a/drivers/cpufreq/amd-pstate.c b/drivers/cpufreq/amd-pstate.c
> new file mode 100644
> index 000000000000..693d796eae55
> --- /dev/null
> +++ b/drivers/cpufreq/amd-pstate.c
> @@ -0,0 +1,446 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * amd-pstate.c - AMD Processor P-state Frequency Driver
> + *
> + * Copyright (C) 2021 Advanced Micro Devices, Inc. All Rights Reserved.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
> + *

You've included the SPDX identifier, you shouldn't need to include the license
information text also.

> + * Author: Huang Rui <ray.huang@amd.com>
> + */
> +
> +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/smp.h>
> +#include <linux/sched.h>
> +#include <linux/cpufreq.h>
> +#include <linux/compiler.h>
> +#include <linux/dmi.h>
> +#include <linux/slab.h>
> +#include <linux/acpi.h>
> +#include <linux/io.h>
> +#include <linux/delay.h>
> +#include <linux/uaccess.h>
> +#include <linux/static_call.h>
> +
> +#include <acpi/processor.h>
> +#include <acpi/cppc_acpi.h>
> +
> +#include <asm/msr.h>
> +#include <asm/processor.h>
> +#include <asm/cpufeature.h>
> +#include <asm/cpu_device_id.h>
> +
> +#define AMD_PSTATE_TRANSITION_LATENCY	0x20000
> +#define AMD_PSTATE_TRANSITION_DELAY	500
> +
> +static struct cpufreq_driver amd_pstate_driver;
> +
> +struct amd_cpudata {
> +	int	cpu;
> +
> +	struct freq_qos_request req[2];
> +	struct cpufreq_policy *policy;

You include a pointer back to the policy, it's is set in amd_pstate_cpu_init()
but isn't used anywhere. This could be dropped from the struct.

> +
> +	u64	cppc_req_cached;
> +
> +	u32	highest_perf;
> +	u32	nominal_perf;
> +	u32	lowest_nonlinear_perf;
> +	u32	lowest_perf;

The lowest_perf value is saved but never referenced, should this be dropped?

It looks like it is used in a later patch to report the lowest_perf value in
sysfs. Do we need to cache it for that? Could just read the value when requested.

> +
> +	u32	max_freq;
> +	u32	min_freq;
> +	u32	nominal_freq;

You're saving the nominal freq value here but I don't see that it is used
anywhere. It looks like you grab the current nominal freq value via
cppc_get_perf_caps() instead. This could be dropped from the struct.

> +	u32	lowest_nonlinear_freq;

The same goes for lowest_nonlinear_freq.

> +};
> +
> +static inline int pstate_enable(bool enable)
> +{
> +	return wrmsrl_safe(MSR_AMD_CPPC_ENABLE, enable ? 1 : 0);
> +}
> +
> +DEFINE_STATIC_CALL(amd_pstate_enable, pstate_enable);
> +
> +static inline int amd_pstate_enable(bool enable)
> +{
> +	return static_call(amd_pstate_enable)(enable);
> +}
> +
> +static int pstate_init_perf(struct amd_cpudata *cpudata)
> +{
> +	u64 cap1;
> +
> +	int ret = rdmsrl_safe_on_cpu(cpudata->cpu, MSR_AMD_CPPC_CAP1,
> +				     &cap1);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * TODO: Introduce AMD specific power feature.
> +	 *
> +	 * CPPC entry doesn't indicate the highest performance in some ASICs.
> +	 */
> +	WRITE_ONCE(cpudata->highest_perf, amd_get_highest_perf());
> +
> +	WRITE_ONCE(cpudata->nominal_perf, CAP1_NOMINAL_PERF(cap1));
> +	WRITE_ONCE(cpudata->lowest_nonlinear_perf, CAP1_LOWNONLIN_PERF(cap1));
> +	WRITE_ONCE(cpudata->lowest_perf, CAP1_LOWEST_PERF(cap1));
> +
> +	return 0;
> +}
> +
> +DEFINE_STATIC_CALL(amd_pstate_init_perf, pstate_init_perf);
> +
> +static inline int amd_pstate_init_perf(struct amd_cpudata *cpudata)
> +{
> +	return static_call(amd_pstate_init_perf)(cpudata);
> +}
> +
> +static void pstate_update_perf(struct amd_cpudata *cpudata, u32 min_perf,
> +			       u32 des_perf, u32 max_perf,
> +			       bool fast_switch)
> +{
> +	if (fast_switch)
> +		wrmsrl(MSR_AMD_CPPC_REQ, READ_ONCE(cpudata->cppc_req_cached));
> +	else
> +		wrmsrl_on_cpu(cpudata->cpu, MSR_AMD_CPPC_REQ,
> +			      READ_ONCE(cpudata->cppc_req_cached));
> +}
> +
> +DEFINE_STATIC_CALL(amd_pstate_update_perf, pstate_update_perf);
> +
> +static inline void
> +amd_pstate_update_perf(struct amd_cpudata *cpudata, u32 min_perf,

Please be consistant on function definition, this should all be on
one line (here and elsewhere);

> +		       u32 des_perf, u32 max_perf, bool fast_switch)
> +{
> +	static_call(amd_pstate_update_perf)(cpudata, min_perf, des_perf,
> +					    max_perf, fast_switch);
> +}
> +
> +static void
> +amd_pstate_update(struct amd_cpudata *cpudata, u32 min_perf,
> +		  u32 des_perf, u32 max_perf, bool fast_switch)
> +{
> +	u64 prev = READ_ONCE(cpudata->cppc_req_cached);
> +	u64 value = prev;
> +
> +	value &= ~REQ_MIN_PERF(~0L);
> +	value |= REQ_MIN_PERF(min_perf);
> +
> +	value &= ~REQ_DES_PERF(~0L);
> +	value |= REQ_DES_PERF(des_perf);
> +
> +	value &= ~REQ_MAX_PERF(~0L);
> +	value |= REQ_MAX_PERF(max_perf);
> +
> +	if (value == prev)
> +		return;
> +
> +	WRITE_ONCE(cpudata->cppc_req_cached, value);
> +
> +	amd_pstate_update_perf(cpudata, min_perf, des_perf,
> +			       max_perf, fast_switch);
> +}
> +
> +static int amd_pstate_verify(struct cpufreq_policy_data *policy)
> +{
> +	cpufreq_verify_within_cpu_limits(policy);
> +
> +	return 0;
> +}
> +
> +static int amd_pstate_target(struct cpufreq_policy *policy,
> +			     unsigned int target_freq,
> +			     unsigned int relation)
> +{
> +	struct cpufreq_freqs freqs;
> +	struct amd_cpudata *cpudata = policy->driver_data;
> +	unsigned long amd_max_perf, amd_min_perf, amd_des_perf,
> +		      amd_cap_perf;
> +
> +	if (!cpudata->max_freq)
> +		return -ENODEV;
> +
> +	amd_cap_perf = READ_ONCE(cpudata->highest_perf);
> +	amd_min_perf = READ_ONCE(cpudata->lowest_nonlinear_perf);

can you help me understand why you use the cached value for lowest
nonlinear perf here but use the value returned from cppc_get_perf_caps()
in amd_get_lowest_nonlinear_freq()?

Should we be using the value from cppc_get_perf_caps() in both cases?

> +	amd_max_perf = amd_cap_perf;
> +
> +	freqs.old = policy->cur;
> +	freqs.new = target_freq;
> +
> +	amd_des_perf = DIV_ROUND_CLOSEST(target_freq * amd_cap_perf,
> +					 cpudata->max_freq);
> +
> +	cpufreq_freq_transition_begin(policy, &freqs);
> +	amd_pstate_update(cpudata, amd_min_perf, amd_des_perf,
> +			  amd_max_perf, false);
> +	cpufreq_freq_transition_end(policy, &freqs, false);
> +
> +	return 0;
> +}
> +
> +static int amd_get_min_freq(struct amd_cpudata *cpudata)
> +{
> +	struct cppc_perf_caps cppc_perf;
> +
> +	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
> +	if (ret)
> +		return ret;
> +
> +	/* Switch to khz */
> +	return cppc_perf.lowest_freq * 1000;
> +}
> +
> +static int amd_get_max_freq(struct amd_cpudata *cpudata)
> +{
> +	struct cppc_perf_caps cppc_perf;
> +	u32 max_perf, max_freq, nominal_freq, nominal_perf;
> +	u64 boost_ratio;
> +
> +	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
> +	if (ret)
> +		return ret;
> +
> +	nominal_freq = cppc_perf.nominal_freq;
> +	nominal_perf = READ_ONCE(cpudata->nominal_perf);
> +	max_perf = READ_ONCE(cpudata->highest_perf);
> +
> +	boost_ratio = div_u64(max_perf << SCHED_CAPACITY_SHIFT,
> +			      nominal_perf);
> +
> +	max_freq = nominal_freq * boost_ratio >> SCHED_CAPACITY_SHIFT;
> +
> +	/* Switch to khz */
> +	return max_freq * 1000;
> +}
> +
> +static int amd_get_nominal_freq(struct amd_cpudata *cpudata)
> +{
> +	struct cppc_perf_caps cppc_perf;
> +	u32 nominal_freq;
> +
> +	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
> +	if (ret)
> +		return ret;
> +
> +	nominal_freq = cppc_perf.nominal_freq;
> +
> +	/* Switch to khz */
> +	return nominal_freq * 1000;
> +}
> +
> +static int amd_get_lowest_nonlinear_freq(struct amd_cpudata *cpudata)
> +{
> +	struct cppc_perf_caps cppc_perf;
> +	u32 lowest_nonlinear_freq, lowest_nonlinear_perf,
> +	    nominal_freq, nominal_perf;
> +	u64 lowest_nonlinear_ratio;
> +
> +	int ret = cppc_get_perf_caps(cpudata->cpu, &cppc_perf);
> +	if (ret)
> +		return ret;
> +
> +	nominal_freq = cppc_perf.nominal_freq;
> +	nominal_perf = READ_ONCE(cpudata->nominal_perf);
> +
> +	lowest_nonlinear_perf = cppc_perf.lowest_nonlinear_perf;
> +
> +	lowest_nonlinear_ratio = div_u64(lowest_nonlinear_perf <<
> +					 SCHED_CAPACITY_SHIFT, nominal_perf);
> +
> +	lowest_nonlinear_freq = nominal_freq * lowest_nonlinear_ratio >> SCHED_CAPACITY_SHIFT;
> +
> +	/* Switch to khz */
> +	return lowest_nonlinear_freq * 1000;
> +}
> +
> +static int amd_pstate_init_freqs_in_cpudata(struct amd_cpudata *cpudata,
> +					    u32 max_freq, u32 min_freq,
> +					    u32 nominal_freq,
> +					    u32 lowest_nonlinear_freq)

This is only called from one place (below in amd_pstate_cpu_init()),
this could just be inline below

-Nathan

> +{
> +	if (!cpudata)
> +		return -EINVAL;
> +
> +	/* Initial processor data capability frequencies */
> +	cpudata->max_freq = max_freq;
> +	cpudata->min_freq = min_freq;
> +	cpudata->nominal_freq = nominal_freq;
> +	cpudata->lowest_nonlinear_freq = lowest_nonlinear_freq;
> +
> +	return 0;
> +}
> +
> +static int amd_pstate_cpu_init(struct cpufreq_policy *policy)
> +{
> +	int min_freq, max_freq, nominal_freq, lowest_nonlinear_freq, ret;
> +	unsigned int cpu = policy->cpu;
> +	struct device *dev;
> +	struct amd_cpudata *cpudata;
> +
> +	dev = get_cpu_device(policy->cpu);
> +	if (!dev)
> +		return -ENODEV;
> +
> +	cpudata = kzalloc(sizeof(*cpudata), GFP_KERNEL);
> +	if (!cpudata)
> +		return -ENOMEM;
> +
> +	cpudata->cpu = cpu;
> +	cpudata->policy = policy;
> +
> +	ret = amd_pstate_init_perf(cpudata);
> +	if (ret)
> +		goto free_cpudata1;
> +
> +	min_freq = amd_get_min_freq(cpudata);
> +	max_freq = amd_get_max_freq(cpudata);
> +	nominal_freq = amd_get_nominal_freq(cpudata);
> +	lowest_nonlinear_freq = amd_get_lowest_nonlinear_freq(cpudata);
> +
> +	if (min_freq < 0 || max_freq < 0 || min_freq > max_freq) {
> +		dev_err(dev, "min_freq(%d) or max_freq(%d) value is incorrect\n",
> +			min_freq, max_freq);
> +		ret = -EINVAL;
> +		goto free_cpudata1;
> +	}
> +
> +	policy->cpuinfo.transition_latency = AMD_PSTATE_TRANSITION_LATENCY;
> +	policy->transition_delay_us = AMD_PSTATE_TRANSITION_DELAY;
> +
> +	policy->min = min_freq;
> +	policy->max = max_freq;
> +
> +	policy->cpuinfo.min_freq = min_freq;
> +	policy->cpuinfo.max_freq = max_freq;
> +
> +	/* It will be updated by governor */
> +	policy->cur = policy->cpuinfo.min_freq;
> +
> +	ret = freq_qos_add_request(&policy->constraints, &cpudata->req[0],
> +				   FREQ_QOS_MIN, policy->cpuinfo.min_freq);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to add min-freq constraint (%d)\n", ret);
> +		goto free_cpudata1;
> +	}
> +
> +	ret = freq_qos_add_request(&policy->constraints, &cpudata->req[1],
> +				   FREQ_QOS_MAX, policy->cpuinfo.max_freq);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to add max-freq constraint (%d)\n", ret);
> +		goto free_cpudata2;
> +	}
> +
> +	ret = amd_pstate_init_freqs_in_cpudata(cpudata, max_freq, min_freq,
> +					       nominal_freq,
> +					       lowest_nonlinear_freq);
> +	if (ret) {
> +		dev_err(dev, "Failed to init cpudata (%d)\n", ret);
> +		goto free_cpudata3;
> +	}
> +
> +	policy->driver_data = cpudata;
> +
> +	return 0;
> +
> +free_cpudata3:
> +	freq_qos_remove_request(&cpudata->req[1]);
> +free_cpudata2:
> +	freq_qos_remove_request(&cpudata->req[0]);
> +free_cpudata1:
> +	kfree(cpudata);
> +	return ret;
> +}
> +
> +static int amd_pstate_cpu_exit(struct cpufreq_policy *policy)
> +{
> +	struct amd_cpudata *cpudata;
> +
> +	cpudata = policy->driver_data;
> +
> +	freq_qos_remove_request(&cpudata->req[1]);
> +	freq_qos_remove_request(&cpudata->req[0]);
> +	kfree(cpudata);
> +
> +	return 0;
> +}
> +
> +static struct cpufreq_driver amd_pstate_driver = {
> +	.flags		= CPUFREQ_CONST_LOOPS | CPUFREQ_NEED_UPDATE_LIMITS,
> +	.verify		= amd_pstate_verify,
> +	.target		= amd_pstate_target,
> +	.init		= amd_pstate_cpu_init,
> +	.exit		= amd_pstate_cpu_exit,
> +	.name		= "amd-pstate",
> +};
> +
> +static int __init amd_pstate_init(void)
> +{
> +	int ret;
> +
> +	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
> +		return -ENODEV;
> +
> +	if (!acpi_cpc_valid()) {
> +		pr_debug("%s, the _CPC object is not present in SBIOS\n",
> +			 __func__);
> +		return -ENODEV;
> +	}
> +
> +	/* don't keep reloading if cpufreq_driver exists */
> +	if (cpufreq_get_current_driver())
> +		return -EEXIST;
> +
> +	/* capability check */
> +	if (!boot_cpu_has(X86_FEATURE_AMD_CPPC)) {
> +		pr_debug("%s, AMD CPPC MSR based functionality is not supported\n",
> +			 __func__);
> +		return -ENODEV;
> +	}
> +
> +	/* enable amd pstate feature */
> +	ret = amd_pstate_enable(true);
> +	if (ret) {
> +		pr_err("%s, failed to enable amd-pstate with return %d\n",
> +		       __func__, ret);
> +		return ret;
> +	}
> +
> +	ret = cpufreq_register_driver(&amd_pstate_driver);
> +	if (ret) {
> +		pr_err("%s, return %d\n", __func__, ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static void __exit amd_pstate_exit(void)
> +{
> +	cpufreq_unregister_driver(&amd_pstate_driver);
> +
> +	amd_pstate_enable(false);
> +}
> +
> +module_init(amd_pstate_init);
> +module_exit(amd_pstate_exit);
> +
> +MODULE_AUTHOR("Huang Rui <ray.huang@amd.com>");
> +MODULE_DESCRIPTION("AMD Processor P-state Frequency Driver");
> +MODULE_LICENSE("GPL");
> -- 
> 2.25.1
>