From: Marek Vasut <marex@denx.de>
To: linux-arm-kernel@lists.infradead.org
Cc: Shawn Guo <shawnguo@kernel.org>
Subject: Re: [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board
Date: Mon, 18 Feb 2019 13:04:36 +0100 [thread overview]
Message-ID: <623d8c58-ff65-2a9c-ec56-2a81382b8391@denx.de> (raw)
In-Reply-To: <20181004224227.16836-2-marex@denx.de>
On 10/5/18 12:42 AM, Marek Vasut wrote:
> Add device tree for the Menlosystems board based on i.MX53 M53 SoM.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
Shawn, bump ?
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx53-m53menlo.dts | 327 +++++++++++++++++++++++++++
> 2 files changed, 328 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx53-m53menlo.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b0e966d625b9..731fc7de76b3 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -376,6 +376,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
> imx53-kp-ddc.dtb \
> imx53-kp-hsc.dtb \
> imx53-m53evk.dtb \
> + imx53-m53menlo.dtb \
> imx53-mba53.dtb \
> imx53-ppd.dtb \
> imx53-qsb.dtb \
> diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
> new file mode 100644
> index 000000000000..405a57ad01a7
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx53-m53menlo.dts
> @@ -0,0 +1,327 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2017 Marek Vasut <marex@denx.de>
> + */
> +
> +/dts-v1/;
> +#include "imx53-m53.dtsi"
> +
> +/ {
> + model = "MENLO M53 EMBEDDED DEVICE";
> + compatible = "fsl,imx53";
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pin_gpio>;
> +
> + user1 {
> + label = "TestLed601";
> + gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc0";
> + };
> +
> + user2 {
> + label = "TestLed602";
> + gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + eth {
> + label = "EthLedYe";
> + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "none";
> + };
> + };
> +
> + panel {
> + compatible = "edt,etm070080dh6";
> + enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_usbh1_vbus: regulator@3 {
> + compatible = "regulator-fixed";
> + reg = <3>;
> + regulator-name = "vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 2 0>;
> + };
> + };
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can1>;
> + status = "okay";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_can2>;
> + status = "okay";
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX5_CLK_CKO1_SEL>,
> + <&clks IMX5_CLK_CKO1_PODF>,
> + <&clks IMX5_CLK_CKO1>;
> + assigned-clock-parents = <&clks IMX5_CLK_AHB>;
> + assigned-clock-rates = <133333334>, <33333334>, <33333334>;
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "rmii";
> + status = "okay";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + edt-ft5x06@38 {
> + compatible = "edt,edt-ft5x06";
> + reg = <0x38>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_edt_ft5x06>;
> + interrupt-parent = <&gpio6>;
> + interrupts = <5 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
> + };
> +
> + eeprom@50 {
> + compatible = "atmel,24c64";
> + reg = <0x50>;
> + pagesize = <32>;
> + };
> +
> + dac@60 {
> + compatible = "microchip,mcp4725";
> + reg = <0x60>;
> + };
> +};
> +
> +&i2c2 {
> + stmpe610@41 {
> + status = "disabled";
> + };
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx53-m53evk {
> + hoggrp {
> + fsl,pins = <
> + MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000
> + MX53_PAD_EIM_EB3__GPIO2_31 0x80000000
> + MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000
> + MX53_PAD_GPIO_19__CCM_CLKO 0x1d5
> + MX53_PAD_CSI0_MCLK__CCM_CSI0_MCLK 0x1d5
> + MX53_PAD_CSI0_DAT4__GPIO5_22 0x1d5
> + MX53_PAD_CSI0_DAT5__GPIO5_23 0x1d5
> + MX53_PAD_CSI0_DAT6__GPIO5_24 0x1d5
> + MX53_PAD_CSI0_DAT7__GPIO5_25 0x1d5
> + MX53_PAD_CSI0_DAT8__GPIO5_26 0x1d5
> + MX53_PAD_CSI0_DAT9__GPIO5_27 0x1d5
> + MX53_PAD_CSI0_DAT10__GPIO5_28 0x1d5
> + MX53_PAD_CSI0_DAT11__GPIO5_29 0x1d5
> + MX53_PAD_CSI0_DAT14__GPIO6_0 0x1d5
> + >;
> + };
> +
> + led_pin_gpio: led_gpio@0 {
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT15__GPIO6_1 0x1d5
> + MX53_PAD_CSI0_DAT16__GPIO6_2 0x1d5
> + >;
> + };
> +
> + pinctrl_can1: can1grp {
> + fsl,pins = <
> + MX53_PAD_GPIO_7__CAN1_TXCAN 0x80000000
> + MX53_PAD_GPIO_8__CAN1_RXCAN 0x80000000
> + >;
> + };
> +
> + pinctrl_can2: can2grp {
> + fsl,pins = <
> + MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000
> + MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000
> + >;
> + };
> +
> + pinctrl_display_gpio: display-gpiogrp {
> + fsl,pins = <
> + MX53_PAD_CSI0_DAT12__GPIO5_30 0x1d5 /* Reset */
> + MX53_PAD_CSI0_DAT13__GPIO5_31 0x1d5 /* Interrupt */
> + >;
> + };
> +
> + pinctrl_edt_ft5x06: edt-ft5x06grp {
> + fsl,pins = <
> + MX53_PAD_PATA_DATA9__GPIO2_9 0x1d5 /* Reset */
> + MX53_PAD_CSI0_DAT19__GPIO6_5 0x1d5 /* Interrupt */
> + MX53_PAD_PATA_DATA10__GPIO2_10 0x1d5 /* Wake */
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
> + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
> + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
> + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
> + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
> + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000
> + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000
> + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000
> + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000
> + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000
> + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000
> + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000
> + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000
> + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000
> + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000
> + MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000
> + MX53_PAD_GPIO_5__I2C3_SCL 0xc0000000
> + >;
> + };
> +
> + pinctrl_lvds0: lvds0grp {
> + fsl,pins = <
> + MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000
> + MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000
> + MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000
> + MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000
> + MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000
> + >;
> + };
> +
> + pinctrl_power_button_gpio: powerbutgrp {
> + fsl,pins = <
> + MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD 0x1d5
> + >;
> + };
> +
> + pinctrl_power_out_gpio: poweroutgrp {
> + fsl,pins = <
> + MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD 0x1d5
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4
> + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4
> + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4
> + >;
> + };
> +
> + pinctrl_usb: usbgrp {
> + fsl,pins = <
> + MX53_PAD_GPIO_2__GPIO1_2 0x80000000
> + MX53_PAD_GPIO_3__USBOH3_USBH1_OC 0x80000000
> + >;
> + };
> + };
> +};
> +
> +&ldb {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lvds0>;
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <18>;
> + status = "okay";
> +
> + port@2 {
> + reg = <2>;
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb>;
> + vbus-supply = <®_usbh1_vbus>;
> + phy_type = "utmi";
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&usbotg {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-02-18 12:04 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-04 22:42 [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Marek Vasut
2018-10-04 22:42 ` Marek Vasut
2018-10-04 22:42 ` [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board Marek Vasut
2019-02-18 12:04 ` Marek Vasut [this message]
2019-02-28 14:37 ` Shawn Guo
2019-03-02 14:52 ` Marek Vasut
2018-10-16 22:32 ` [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Rob Herring
2018-10-16 22:32 ` Rob Herring
2019-02-19 14:06 ` Marek Vasut
2019-02-19 14:06 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=623d8c58-ff65-2a9c-ec56-2a81382b8391@denx.de \
--to=marex@denx.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.