[PATCH v7 00/12] clk: Improve clock range handling

[PATCH v7 00/12] clk: Improve clock range handling

[Maxime Ripard]

Hi,

This is a follow-up of the discussion here:
https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/

and here:
https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/

While the initial proposal implemented a new API to temporarily raise and lower
clock rates based on consumer workloads, Stephen suggested an
alternative approach implemented here.

The main issue that needed to be addressed in our case was that in a
situation where we would have multiple calls to clk_set_rate_range, we
would end up with a clock at the maximum of the minimums being set. This
would be expected, but the issue was that if one of the users was to
relax or drop its requirements, the rate would be left unchanged, even
though the ideal rate would have changed.

So something like

clk_set_rate(user1_clk, 1000);
clk_set_min_rate(user1_clk, 2000);
clk_set_min_rate(user2_clk, 3000);
clk_set_min_rate(user2_clk, 1000);

Would leave the clock running at 3000Hz, while the minimum would now be
2000Hz.

This was mostly due to the fact that the core only triggers a rate
change in clk_set_rate_range() if the current rate is outside of the
boundaries, but not if it's within the new boundaries.

That series changes that and will trigger a rate change on every call,
with the former rate being tried again. This way, providers have a
chance to follow whatever policy they see fit for a given clock each
time the boundaries change.

This series also implements some kunit tests, first to test a few rate
related functions in the CCF, and then extends it to make sure that
behaviour has some test coverage.

Let me know what you think
Maxime

Changes from v6:
  - Removed unused header
  - Used more fitting KUNIT macros
  - Enhanced some comments
  - Reworded a commit message

Changes from v5:
  - Changed clk_hw_create_clk for clk_hw_get_clk since the former isn't
    exported to modules.
  - Added fix for clk_hw_get_clk

Changes from v4:
  - Rename the test file
  - Move all the tests to the first patch, and fix them up as fixes are done
  - Improved the test conditions
  - Added more tests
  - Improved commit messages
  - Fixed a regression where two disjoints clock ranges would now be accepted

Changes from v3:
  - Renamed the test file and Kconfig option
  - Add option to .kunitconfig
  - Switch to kunit_kzalloc
  - Use KUNIT_EXPECT_* instead of KUNIT_ASSERT_* where relevant
  - Test directly relevant calls instead of going through a temporary variable
  - Switch to more precise KUNIT_ASSERT_* macros where relevant

Changes from v2:
  - Rebased on current next
  - Rewrote the whole thing according to Stephen reviews
  - Implemented some kunit tests

Changes from v1:
  - Return NULL in clk_request_start if clk pointer is NULL
  - Test for clk_req pointer in clk_request_done
  - Add another user in vc4
  - Rebased on top of v5.15-rc1

Maxime Ripard (12):
  clk: Fix clk_hw_get_clk() when dev is NULL
  clk: Introduce Kunit Tests for the framework
  clk: Enforce that disjoints limits are invalid
  clk: Always clamp the rounded rate
  clk: Use clamp instead of open-coding our own
  clk: Always set the rate on clk_set_range_rate
  clk: Add clk_drop_range
  clk: bcm: rpi: Add variant structure
  clk: bcm: rpi: Set a default minimum rate
  clk: bcm: rpi: Run some clocks at the minimum rate allowed
  drm/vc4: Add logging and comments
  drm/vc4: hdmi: Remove clock rate initialization

 drivers/clk/.kunitconfig          |   1 +
 drivers/clk/Kconfig               |   7 +
 drivers/clk/Makefile              |   1 +
 drivers/clk/bcm/clk-raspberrypi.c | 125 ++++-
 drivers/clk/clk.c                 |  76 ++-
 drivers/clk/clk_test.c            | 795 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/vc4/vc4_hdmi.c    |  13 -
 drivers/gpu/drm/vc4/vc4_kms.c     |  11 +
 include/linux/clk.h               |  11 +
 9 files changed, 985 insertions(+), 55 deletions(-)
 create mode 100644 drivers/clk/clk_test.c

-- 
2.35.1

[PATCH v7 00/12] clk: Improve clock range handling

[Maxime Ripard]

Hi,

This is a follow-up of the discussion here:
https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/

and here:
https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/

While the initial proposal implemented a new API to temporarily raise and lower
clock rates based on consumer workloads, Stephen suggested an
alternative approach implemented here.

The main issue that needed to be addressed in our case was that in a
situation where we would have multiple calls to clk_set_rate_range, we
would end up with a clock at the maximum of the minimums being set. This
would be expected, but the issue was that if one of the users was to
relax or drop its requirements, the rate would be left unchanged, even
though the ideal rate would have changed.

So something like

clk_set_rate(user1_clk, 1000);
clk_set_min_rate(user1_clk, 2000);
clk_set_min_rate(user2_clk, 3000);
clk_set_min_rate(user2_clk, 1000);

Would leave the clock running at 3000Hz, while the minimum would now be
2000Hz.

This was mostly due to the fact that the core only triggers a rate
change in clk_set_rate_range() if the current rate is outside of the
boundaries, but not if it's within the new boundaries.

That series changes that and will trigger a rate change on every call,
with the former rate being tried again. This way, providers have a
chance to follow whatever policy they see fit for a given clock each
time the boundaries change.

This series also implements some kunit tests, first to test a few rate
related functions in the CCF, and then extends it to make sure that
behaviour has some test coverage.

Let me know what you think
Maxime

Changes from v6:
  - Removed unused header
  - Used more fitting KUNIT macros
  - Enhanced some comments
  - Reworded a commit message

Changes from v5:
  - Changed clk_hw_create_clk for clk_hw_get_clk since the former isn't
    exported to modules.
  - Added fix for clk_hw_get_clk

Changes from v4:
  - Rename the test file
  - Move all the tests to the first patch, and fix them up as fixes are done
  - Improved the test conditions
  - Added more tests
  - Improved commit messages
  - Fixed a regression where two disjoints clock ranges would now be accepted

Changes from v3:
  - Renamed the test file and Kconfig option
  - Add option to .kunitconfig
  - Switch to kunit_kzalloc
  - Use KUNIT_EXPECT_* instead of KUNIT_ASSERT_* where relevant
  - Test directly relevant calls instead of going through a temporary variable
  - Switch to more precise KUNIT_ASSERT_* macros where relevant

Changes from v2:
  - Rebased on current next
  - Rewrote the whole thing according to Stephen reviews
  - Implemented some kunit tests

Changes from v1:
  - Return NULL in clk_request_start if clk pointer is NULL
  - Test for clk_req pointer in clk_request_done
  - Add another user in vc4
  - Rebased on top of v5.15-rc1

Maxime Ripard (12):
  clk: Fix clk_hw_get_clk() when dev is NULL
  clk: Introduce Kunit Tests for the framework
  clk: Enforce that disjoints limits are invalid
  clk: Always clamp the rounded rate
  clk: Use clamp instead of open-coding our own
  clk: Always set the rate on clk_set_range_rate
  clk: Add clk_drop_range
  clk: bcm: rpi: Add variant structure
  clk: bcm: rpi: Set a default minimum rate
  clk: bcm: rpi: Run some clocks at the minimum rate allowed
  drm/vc4: Add logging and comments
  drm/vc4: hdmi: Remove clock rate initialization

 drivers/clk/.kunitconfig          |   1 +
 drivers/clk/Kconfig               |   7 +
 drivers/clk/Makefile              |   1 +
 drivers/clk/bcm/clk-raspberrypi.c | 125 ++++-
 drivers/clk/clk.c                 |  76 ++-
 drivers/clk/clk_test.c            | 795 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/vc4/vc4_hdmi.c    |  13 -
 drivers/gpu/drm/vc4/vc4_kms.c     |  11 +
 include/linux/clk.h               |  11 +
 9 files changed, 985 insertions(+), 55 deletions(-)
 create mode 100644 drivers/clk/clk_test.c

-- 
2.35.1

[PATCH v7 01/12] clk: Fix clk_hw_get_clk() when dev is NULL

[Maxime Ripard]

Any registered clk_core structure can have a NULL pointer in its dev
field. While never actually documented, this is evidenced by the wide
usage of clk_register and clk_hw_register with a NULL device pointer,
and the fact that the core of_clk_hw_register() function also passes a
NULL device pointer.

A call to clk_hw_get_clk() on a clk_hw struct whose clk_core is in that
case will result in a NULL pointer derefence when it calls dev_name() on
that NULL device pointer.

Add a test for this case and use NULL as the dev_id if the device
pointer is NULL.

Fixes: 30d6f8c15d2c ("clk: add api to get clk consumer from clk_hw")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 8de6a22498e7..fff5edb89d6d 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -3773,8 +3773,9 @@ struct clk *clk_hw_create_clk(struct device *dev, struct clk_hw *hw,
 struct clk *clk_hw_get_clk(struct clk_hw *hw, const char *con_id)
 {
 	struct device *dev = hw->core->dev;
+	const char *name = dev ? dev_name(dev) : NULL;
 
-	return clk_hw_create_clk(dev, hw, dev_name(dev), con_id);
+	return clk_hw_create_clk(dev, hw, name, con_id);
 }
 EXPORT_SYMBOL(clk_hw_get_clk);
 
-- 
2.35.1

[PATCH v7 01/12] clk: Fix clk_hw_get_clk() when dev is NULL

[Maxime Ripard]

Any registered clk_core structure can have a NULL pointer in its dev
field. While never actually documented, this is evidenced by the wide
usage of clk_register and clk_hw_register with a NULL device pointer,
and the fact that the core of_clk_hw_register() function also passes a
NULL device pointer.

A call to clk_hw_get_clk() on a clk_hw struct whose clk_core is in that
case will result in a NULL pointer derefence when it calls dev_name() on
that NULL device pointer.

Add a test for this case and use NULL as the dev_id if the device
pointer is NULL.

Fixes: 30d6f8c15d2c ("clk: add api to get clk consumer from clk_hw")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 8de6a22498e7..fff5edb89d6d 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -3773,8 +3773,9 @@ struct clk *clk_hw_create_clk(struct device *dev, struct clk_hw *hw,
 struct clk *clk_hw_get_clk(struct clk_hw *hw, const char *con_id)
 {
 	struct device *dev = hw->core->dev;
+	const char *name = dev ? dev_name(dev) : NULL;
 
-	return clk_hw_create_clk(dev, hw, dev_name(dev), con_id);
+	return clk_hw_create_clk(dev, hw, name, con_id);
 }
 EXPORT_SYMBOL(clk_hw_get_clk);
 
-- 
2.35.1

[PATCH v7 02/12] clk: Introduce Kunit Tests for the framework

[Maxime Ripard]

Let's test various parts of the rate-related clock API with the kunit
testing framework.

Cc: kunit-dev@googlegroups.com
Tested-by: Daniel Latypov <dlatypov@google.com>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/.kunitconfig |   1 +
 drivers/clk/Kconfig      |   7 +
 drivers/clk/Makefile     |   1 +
 drivers/clk/clk_test.c   | 787 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 796 insertions(+)
 create mode 100644 drivers/clk/clk_test.c

diff --git a/drivers/clk/.kunitconfig b/drivers/clk/.kunitconfig
index 3754fdb9485a..cdbc7d7deba9 100644
--- a/drivers/clk/.kunitconfig
+++ b/drivers/clk/.kunitconfig
@@ -1,3 +1,4 @@
 CONFIG_KUNIT=y
 CONFIG_COMMON_CLK=y
+CONFIG_CLK_KUNIT_TEST=y
 CONFIG_CLK_GATE_KUNIT_TEST=y
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 3cdf33470a75..2ef6eca297ff 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -429,6 +429,13 @@ source "drivers/clk/xilinx/Kconfig"
 source "drivers/clk/zynqmp/Kconfig"
 
 # Kunit test cases
+config CLK_KUNIT_TEST
+	tristate "Basic Clock Framework Kunit Tests" if !KUNIT_ALL_TESTS
+	depends on KUNIT
+	default KUNIT_ALL_TESTS
+	help
+	  Kunit tests for the common clock framework.
+
 config CLK_GATE_KUNIT_TEST
 	tristate "Basic gate type Kunit test" if !KUNIT_ALL_TESTS
 	depends on KUNIT
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 6a98291350b6..8f9b1daba411 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -2,6 +2,7 @@
 # common clock types
 obj-$(CONFIG_HAVE_CLK)		+= clk-devres.o clk-bulk.o clkdev.o
 obj-$(CONFIG_COMMON_CLK)	+= clk.o
+obj-$(CONFIG_CLK_KUNIT_TEST)	+= clk_test.o
 obj-$(CONFIG_COMMON_CLK)	+= clk-divider.o
 obj-$(CONFIG_COMMON_CLK)	+= clk-fixed-factor.o
 obj-$(CONFIG_COMMON_CLK)	+= clk-fixed-rate.o
diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
new file mode 100644
index 000000000000..a8d7eba01de7
--- /dev/null
+++ b/drivers/clk/clk_test.c
@@ -0,0 +1,787 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Kunit test for clk rate management
+ */
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+
+/* Needed for clk_hw_get_clk() */
+#include "clk.h"
+
+#include <kunit/test.h>
+
+#define DUMMY_CLOCK_INIT_RATE	(42 * 1000 * 1000)
+#define DUMMY_CLOCK_RATE_1	(142 * 1000 * 1000)
+#define DUMMY_CLOCK_RATE_2	(242 * 1000 * 1000)
+
+struct clk_dummy_context {
+	struct clk_hw hw;
+	unsigned long rate;
+};
+
+static unsigned long clk_dummy_recalc_rate(struct clk_hw *hw,
+					   unsigned long parent_rate)
+{
+	struct clk_dummy_context *ctx =
+		container_of(hw, struct clk_dummy_context, hw);
+
+	return ctx->rate;
+}
+
+static int clk_dummy_determine_rate(struct clk_hw *hw,
+				    struct clk_rate_request *req)
+{
+	/* Just return the same rate without modifying it */
+	return 0;
+}
+
+static int clk_dummy_maximize_rate(struct clk_hw *hw,
+				   struct clk_rate_request *req)
+{
+	/*
+	 * If there's a maximum set, always run the clock at the maximum
+	 * allowed.
+	 */
+	if (req->max_rate < ULONG_MAX)
+		req->rate = req->max_rate;
+
+	return 0;
+}
+
+static int clk_dummy_minimize_rate(struct clk_hw *hw,
+				   struct clk_rate_request *req)
+{
+	/*
+	 * If there's a minimum set, always run the clock at the minimum
+	 * allowed.
+	 */
+	if (req->min_rate > 0)
+		req->rate = req->min_rate;
+
+	return 0;
+}
+
+static int clk_dummy_set_rate(struct clk_hw *hw,
+			      unsigned long rate,
+			      unsigned long parent_rate)
+{
+	struct clk_dummy_context *ctx =
+		container_of(hw, struct clk_dummy_context, hw);
+
+	ctx->rate = rate;
+	return 0;
+}
+
+static const struct clk_ops clk_dummy_rate_ops = {
+	.recalc_rate = clk_dummy_recalc_rate,
+	.determine_rate = clk_dummy_determine_rate,
+	.set_rate = clk_dummy_set_rate,
+};
+
+static const struct clk_ops clk_dummy_maximize_rate_ops = {
+	.recalc_rate = clk_dummy_recalc_rate,
+	.determine_rate = clk_dummy_maximize_rate,
+	.set_rate = clk_dummy_set_rate,
+};
+
+static const struct clk_ops clk_dummy_minimize_rate_ops = {
+	.recalc_rate = clk_dummy_recalc_rate,
+	.determine_rate = clk_dummy_minimize_rate,
+	.set_rate = clk_dummy_set_rate,
+};
+
+static int clk_test_init_with_ops(struct kunit *test, const struct clk_ops *ops)
+{
+	struct clk_dummy_context *ctx;
+	struct clk_init_data init = { };
+	int ret;
+
+	ctx = kunit_kzalloc(test, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+	ctx->rate = DUMMY_CLOCK_INIT_RATE;
+	test->priv = ctx;
+
+	init.name = "test_dummy_rate";
+	init.ops = ops;
+	ctx->hw.init = &init;
+
+	ret = clk_hw_register(NULL, &ctx->hw);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int clk_test_init(struct kunit *test)
+{
+	return clk_test_init_with_ops(test, &clk_dummy_rate_ops);
+}
+
+static int clk_maximize_test_init(struct kunit *test)
+{
+	return clk_test_init_with_ops(test, &clk_dummy_maximize_rate_ops);
+}
+
+static int clk_minimize_test_init(struct kunit *test)
+{
+	return clk_test_init_with_ops(test, &clk_dummy_minimize_rate_ops);
+}
+
+static void clk_test_exit(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+
+	clk_hw_unregister(&ctx->hw);
+}
+
+/*
+ * Test that the actual rate matches what is returned by clk_get_rate()
+ */
+static void clk_test_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, ctx->rate);
+}
+
+/*
+ * Test that, after a call to clk_set_rate(), the rate returned by
+ * clk_get_rate() matches.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_test_set_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+}
+
+/*
+ * Test that, after several calls to clk_set_rate(), the rate returned
+ * by clk_get_rate() matches the last one.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_test_set_set_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+}
+
+/*
+ * Test that clk_round_rate and clk_set_rate are consitent and will
+ * return the same frequency.
+ */
+static void clk_test_round_set_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rounded_rate, set_rate;
+
+	rounded_rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_1);
+	KUNIT_ASSERT_GT(test, rounded_rate, 0);
+	KUNIT_EXPECT_EQ(test, rounded_rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1),
+			0);
+
+	set_rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, set_rate, 0);
+	KUNIT_EXPECT_EQ(test, rounded_rate, set_rate);
+}
+
+static struct kunit_case clk_test_cases[] = {
+	KUNIT_CASE(clk_test_get_rate),
+	KUNIT_CASE(clk_test_set_get_rate),
+	KUNIT_CASE(clk_test_set_set_get_rate),
+	KUNIT_CASE(clk_test_round_set_get_rate),
+	{}
+};
+
+static struct kunit_suite clk_test_suite = {
+	.name = "clk-test",
+	.init = clk_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_test_cases,
+};
+
+/*
+ * Test that clk_set_rate_range won't return an error for a valid range
+ * and that it will make sure the rate of the clock is within the
+ * boundaries.
+ */
+static void clk_range_test_set_range(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
+}
+
+/*
+ * Test that calling clk_set_rate_range with a minimum rate higher than
+ * the maximum rate returns an error.
+ */
+static void clk_range_test_set_range_invalid(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1 + 1000,
+					   DUMMY_CLOCK_RATE_1),
+			0);
+}
+
+/*
+ * Test that users can't set multiple, disjoints, range that would be
+ * impossible to meet.
+ */
+static void clk_range_test_multiple_disjoints_range(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *user1, *user2;
+
+	user1 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user1);
+
+	user2 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user1, 1000, 2000),
+			0);
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate_range(user2, 3000, 4000),
+			0);
+
+	clk_put(user2);
+	clk_put(user1);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round a rate
+ * lower than the minimum, the returned rate won't be affected by the
+ * boundaries.
+ */
+static void clk_range_test_set_range_round_rate_lower(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 - 1000);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to set a rate
+ * lower than the minimum, we'll get an error.
+ */
+static void clk_range_test_set_range_set_rate_lower(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	KUNIT_ASSERT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round and
+ * set a rate lower than the minimum, the values won't be consistent
+ * between clk_round_rate() and clk_set_rate().
+ */
+static void clk_range_test_set_range_set_round_rate_consistent_lower(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rounded;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
+	KUNIT_ASSERT_GT(test, rounded, 0);
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+
+	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round a rate
+ * higher than the maximum, the returned rate won't be affected by the
+ * boundaries.
+ */
+static void clk_range_test_set_range_round_rate_higher(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 + 1000);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to set a rate
+ * lower than the maximum, we'll get an error.
+ */
+static void clk_range_test_set_range_set_rate_higher(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	KUNIT_ASSERT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round and
+ * set a rate higher than the maximum, the values won't be consistent
+ * between clk_round_rate() and clk_set_rate().
+ */
+static void clk_range_test_set_range_set_round_rate_consistent_higher(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rounded;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
+	KUNIT_ASSERT_GT(test, rounded, 0);
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+}
+
+/*
+ * Test that if our clock has a rate lower than the minimum set by a
+ * call to clk_set_rate_range(), the rate will be raised to match the
+ * new minimum.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_range_test_set_range_get_rate_raised(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+}
+
+/*
+ * Test that if our clock has a rate higher than the maximum set by a
+ * call to clk_set_rate_range(), the rate will be lowered to match the
+ * new maximum.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_range_test_set_range_get_rate_lowered(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+}
+
+static struct kunit_case clk_range_test_cases[] = {
+	KUNIT_CASE(clk_range_test_set_range),
+	KUNIT_CASE(clk_range_test_set_range_invalid),
+	KUNIT_CASE(clk_range_test_multiple_disjoints_range),
+	KUNIT_CASE(clk_range_test_set_range_round_rate_lower),
+	KUNIT_CASE(clk_range_test_set_range_set_rate_lower),
+	KUNIT_CASE(clk_range_test_set_range_set_round_rate_consistent_lower),
+	KUNIT_CASE(clk_range_test_set_range_round_rate_higher),
+	KUNIT_CASE(clk_range_test_set_range_set_rate_higher),
+	KUNIT_CASE(clk_range_test_set_range_set_round_rate_consistent_higher),
+	KUNIT_CASE(clk_range_test_set_range_get_rate_raised),
+	KUNIT_CASE(clk_range_test_set_range_get_rate_lowered),
+	{}
+};
+
+static struct kunit_suite clk_range_test_suite = {
+	.name = "clk-range-test",
+	.init = clk_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_range_test_cases,
+};
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range();
+ * - and we have a round_rate ops that always return the maximum
+ *   frequency allowed;
+ *
+ * The clock will run at the minimum of all maximum boundaries
+ * requested, even if those boundaries aren't there anymore.
+ */
+static void clk_range_test_set_range_rate_maximized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2 - 1000),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 - 1000);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 - 1000);
+}
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range(), across
+ *   multiple users;
+ * - and we have a round_rate ops that always return the maximum
+ *   frequency allowed;
+ *
+ * The clock will run at the minimum of all maximum boundaries
+ * requested, even if those boundaries aren't there anymore.
+ */
+static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	struct clk *user1, *user2;
+	unsigned long rate;
+
+	user1 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user1);
+
+	user2 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user1,
+					   0,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2,
+					   0,
+					   DUMMY_CLOCK_RATE_1),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2, 0, ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	clk_put(user2);
+	clk_put(user1);
+}
+
+static struct kunit_case clk_range_maximize_test_cases[] = {
+	KUNIT_CASE(clk_range_test_set_range_rate_maximized),
+	KUNIT_CASE(clk_range_test_multiple_set_range_rate_maximized),
+	{}
+};
+
+static struct kunit_suite clk_range_maximize_test_suite = {
+	.name = "clk-range-maximize-test",
+	.init = clk_maximize_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_range_maximize_test_cases,
+};
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range()
+ * - and we have a round_rate ops that always return the minimum
+ *   frequency allowed;
+ *
+ * The clock will run at the maximum of all minimum boundaries
+ * requested, even if those boundaries aren't there anymore.
+*/
+static void clk_range_test_set_range_rate_minimized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1 + 1000,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 + 1000);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 + 1000);
+}
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range(), across
+ *   multiple users;
+ * - and we have a round_rate ops that always return the minimum
+ *   frequency allowed;
+ *
+ * The clock will run at the maximum of all minimum boundaries
+ * requested, even if those boundaries aren't there anymore.
+*/
+static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	struct clk *user1, *user2;
+	unsigned long rate;
+
+	user1 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user1);
+
+	user2 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user1,
+					   DUMMY_CLOCK_RATE_1,
+					   ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2,
+					   DUMMY_CLOCK_RATE_2,
+					   ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2, 0, ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	clk_put(user2);
+	clk_put(user1);
+}
+
+static struct kunit_case clk_range_minimize_test_cases[] = {
+	KUNIT_CASE(clk_range_test_set_range_rate_minimized),
+	KUNIT_CASE(clk_range_test_multiple_set_range_rate_minimized),
+	{}
+};
+
+static struct kunit_suite clk_range_minimize_test_suite = {
+	.name = "clk-range-minimize-test",
+	.init = clk_minimize_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_range_minimize_test_cases,
+};
+
+kunit_test_suites(
+	&clk_test_suite,
+	&clk_range_test_suite,
+	&clk_range_maximize_test_suite,
+	&clk_range_minimize_test_suite
+);
+MODULE_LICENSE("GPL v2");
-- 
2.35.1

[PATCH v7 02/12] clk: Introduce Kunit Tests for the framework

[Maxime Ripard]

Let's test various parts of the rate-related clock API with the kunit
testing framework.

Cc: kunit-dev@googlegroups.com
Tested-by: Daniel Latypov <dlatypov@google.com>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/.kunitconfig |   1 +
 drivers/clk/Kconfig      |   7 +
 drivers/clk/Makefile     |   1 +
 drivers/clk/clk_test.c   | 787 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 796 insertions(+)
 create mode 100644 drivers/clk/clk_test.c

diff --git a/drivers/clk/.kunitconfig b/drivers/clk/.kunitconfig
index 3754fdb9485a..cdbc7d7deba9 100644
--- a/drivers/clk/.kunitconfig
+++ b/drivers/clk/.kunitconfig
@@ -1,3 +1,4 @@
 CONFIG_KUNIT=y
 CONFIG_COMMON_CLK=y
+CONFIG_CLK_KUNIT_TEST=y
 CONFIG_CLK_GATE_KUNIT_TEST=y
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 3cdf33470a75..2ef6eca297ff 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -429,6 +429,13 @@ source "drivers/clk/xilinx/Kconfig"
 source "drivers/clk/zynqmp/Kconfig"
 
 # Kunit test cases
+config CLK_KUNIT_TEST
+	tristate "Basic Clock Framework Kunit Tests" if !KUNIT_ALL_TESTS
+	depends on KUNIT
+	default KUNIT_ALL_TESTS
+	help
+	  Kunit tests for the common clock framework.
+
 config CLK_GATE_KUNIT_TEST
 	tristate "Basic gate type Kunit test" if !KUNIT_ALL_TESTS
 	depends on KUNIT
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 6a98291350b6..8f9b1daba411 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -2,6 +2,7 @@
 # common clock types
 obj-$(CONFIG_HAVE_CLK)		+= clk-devres.o clk-bulk.o clkdev.o
 obj-$(CONFIG_COMMON_CLK)	+= clk.o
+obj-$(CONFIG_CLK_KUNIT_TEST)	+= clk_test.o
 obj-$(CONFIG_COMMON_CLK)	+= clk-divider.o
 obj-$(CONFIG_COMMON_CLK)	+= clk-fixed-factor.o
 obj-$(CONFIG_COMMON_CLK)	+= clk-fixed-rate.o
diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
new file mode 100644
index 000000000000..a8d7eba01de7
--- /dev/null
+++ b/drivers/clk/clk_test.c
@@ -0,0 +1,787 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Kunit test for clk rate management
+ */
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+
+/* Needed for clk_hw_get_clk() */
+#include "clk.h"
+
+#include <kunit/test.h>
+
+#define DUMMY_CLOCK_INIT_RATE	(42 * 1000 * 1000)
+#define DUMMY_CLOCK_RATE_1	(142 * 1000 * 1000)
+#define DUMMY_CLOCK_RATE_2	(242 * 1000 * 1000)
+
+struct clk_dummy_context {
+	struct clk_hw hw;
+	unsigned long rate;
+};
+
+static unsigned long clk_dummy_recalc_rate(struct clk_hw *hw,
+					   unsigned long parent_rate)
+{
+	struct clk_dummy_context *ctx =
+		container_of(hw, struct clk_dummy_context, hw);
+
+	return ctx->rate;
+}
+
+static int clk_dummy_determine_rate(struct clk_hw *hw,
+				    struct clk_rate_request *req)
+{
+	/* Just return the same rate without modifying it */
+	return 0;
+}
+
+static int clk_dummy_maximize_rate(struct clk_hw *hw,
+				   struct clk_rate_request *req)
+{
+	/*
+	 * If there's a maximum set, always run the clock at the maximum
+	 * allowed.
+	 */
+	if (req->max_rate < ULONG_MAX)
+		req->rate = req->max_rate;
+
+	return 0;
+}
+
+static int clk_dummy_minimize_rate(struct clk_hw *hw,
+				   struct clk_rate_request *req)
+{
+	/*
+	 * If there's a minimum set, always run the clock at the minimum
+	 * allowed.
+	 */
+	if (req->min_rate > 0)
+		req->rate = req->min_rate;
+
+	return 0;
+}
+
+static int clk_dummy_set_rate(struct clk_hw *hw,
+			      unsigned long rate,
+			      unsigned long parent_rate)
+{
+	struct clk_dummy_context *ctx =
+		container_of(hw, struct clk_dummy_context, hw);
+
+	ctx->rate = rate;
+	return 0;
+}
+
+static const struct clk_ops clk_dummy_rate_ops = {
+	.recalc_rate = clk_dummy_recalc_rate,
+	.determine_rate = clk_dummy_determine_rate,
+	.set_rate = clk_dummy_set_rate,
+};
+
+static const struct clk_ops clk_dummy_maximize_rate_ops = {
+	.recalc_rate = clk_dummy_recalc_rate,
+	.determine_rate = clk_dummy_maximize_rate,
+	.set_rate = clk_dummy_set_rate,
+};
+
+static const struct clk_ops clk_dummy_minimize_rate_ops = {
+	.recalc_rate = clk_dummy_recalc_rate,
+	.determine_rate = clk_dummy_minimize_rate,
+	.set_rate = clk_dummy_set_rate,
+};
+
+static int clk_test_init_with_ops(struct kunit *test, const struct clk_ops *ops)
+{
+	struct clk_dummy_context *ctx;
+	struct clk_init_data init = { };
+	int ret;
+
+	ctx = kunit_kzalloc(test, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+	ctx->rate = DUMMY_CLOCK_INIT_RATE;
+	test->priv = ctx;
+
+	init.name = "test_dummy_rate";
+	init.ops = ops;
+	ctx->hw.init = &init;
+
+	ret = clk_hw_register(NULL, &ctx->hw);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int clk_test_init(struct kunit *test)
+{
+	return clk_test_init_with_ops(test, &clk_dummy_rate_ops);
+}
+
+static int clk_maximize_test_init(struct kunit *test)
+{
+	return clk_test_init_with_ops(test, &clk_dummy_maximize_rate_ops);
+}
+
+static int clk_minimize_test_init(struct kunit *test)
+{
+	return clk_test_init_with_ops(test, &clk_dummy_minimize_rate_ops);
+}
+
+static void clk_test_exit(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+
+	clk_hw_unregister(&ctx->hw);
+}
+
+/*
+ * Test that the actual rate matches what is returned by clk_get_rate()
+ */
+static void clk_test_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, ctx->rate);
+}
+
+/*
+ * Test that, after a call to clk_set_rate(), the rate returned by
+ * clk_get_rate() matches.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_test_set_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+}
+
+/*
+ * Test that, after several calls to clk_set_rate(), the rate returned
+ * by clk_get_rate() matches the last one.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_test_set_set_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+}
+
+/*
+ * Test that clk_round_rate and clk_set_rate are consitent and will
+ * return the same frequency.
+ */
+static void clk_test_round_set_get_rate(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rounded_rate, set_rate;
+
+	rounded_rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_1);
+	KUNIT_ASSERT_GT(test, rounded_rate, 0);
+	KUNIT_EXPECT_EQ(test, rounded_rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1),
+			0);
+
+	set_rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, set_rate, 0);
+	KUNIT_EXPECT_EQ(test, rounded_rate, set_rate);
+}
+
+static struct kunit_case clk_test_cases[] = {
+	KUNIT_CASE(clk_test_get_rate),
+	KUNIT_CASE(clk_test_set_get_rate),
+	KUNIT_CASE(clk_test_set_set_get_rate),
+	KUNIT_CASE(clk_test_round_set_get_rate),
+	{}
+};
+
+static struct kunit_suite clk_test_suite = {
+	.name = "clk-test",
+	.init = clk_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_test_cases,
+};
+
+/*
+ * Test that clk_set_rate_range won't return an error for a valid range
+ * and that it will make sure the rate of the clock is within the
+ * boundaries.
+ */
+static void clk_range_test_set_range(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
+}
+
+/*
+ * Test that calling clk_set_rate_range with a minimum rate higher than
+ * the maximum rate returns an error.
+ */
+static void clk_range_test_set_range_invalid(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1 + 1000,
+					   DUMMY_CLOCK_RATE_1),
+			0);
+}
+
+/*
+ * Test that users can't set multiple, disjoints, range that would be
+ * impossible to meet.
+ */
+static void clk_range_test_multiple_disjoints_range(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *user1, *user2;
+
+	user1 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user1);
+
+	user2 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user1, 1000, 2000),
+			0);
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate_range(user2, 3000, 4000),
+			0);
+
+	clk_put(user2);
+	clk_put(user1);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round a rate
+ * lower than the minimum, the returned rate won't be affected by the
+ * boundaries.
+ */
+static void clk_range_test_set_range_round_rate_lower(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 - 1000);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to set a rate
+ * lower than the minimum, we'll get an error.
+ */
+static void clk_range_test_set_range_set_rate_lower(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	KUNIT_ASSERT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round and
+ * set a rate lower than the minimum, the values won't be consistent
+ * between clk_round_rate() and clk_set_rate().
+ */
+static void clk_range_test_set_range_set_round_rate_consistent_lower(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rounded;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
+	KUNIT_ASSERT_GT(test, rounded, 0);
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+
+	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round a rate
+ * higher than the maximum, the returned rate won't be affected by the
+ * boundaries.
+ */
+static void clk_range_test_set_range_round_rate_higher(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 + 1000);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to set a rate
+ * lower than the maximum, we'll get an error.
+ */
+static void clk_range_test_set_range_set_rate_higher(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	KUNIT_ASSERT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+}
+
+/*
+ * Test that if our clock has some boundaries and we try to round and
+ * set a rate higher than the maximum, the values won't be consistent
+ * between clk_round_rate() and clk_set_rate().
+ */
+static void clk_range_test_set_range_set_round_rate_consistent_higher(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	long rounded;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
+	KUNIT_ASSERT_GT(test, rounded, 0);
+
+	KUNIT_EXPECT_LT(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+}
+
+/*
+ * Test that if our clock has a rate lower than the minimum set by a
+ * call to clk_set_rate_range(), the rate will be raised to match the
+ * new minimum.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_range_test_set_range_get_rate_raised(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+}
+
+/*
+ * Test that if our clock has a rate higher than the maximum set by a
+ * call to clk_set_rate_range(), the rate will be lowered to match the
+ * new maximum.
+ *
+ * This assumes that clk_ops.determine_rate or clk_ops.round_rate won't
+ * modify the requested rate, which is our case in clk_dummy_rate_ops.
+ */
+static void clk_range_test_set_range_get_rate_lowered(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+}
+
+static struct kunit_case clk_range_test_cases[] = {
+	KUNIT_CASE(clk_range_test_set_range),
+	KUNIT_CASE(clk_range_test_set_range_invalid),
+	KUNIT_CASE(clk_range_test_multiple_disjoints_range),
+	KUNIT_CASE(clk_range_test_set_range_round_rate_lower),
+	KUNIT_CASE(clk_range_test_set_range_set_rate_lower),
+	KUNIT_CASE(clk_range_test_set_range_set_round_rate_consistent_lower),
+	KUNIT_CASE(clk_range_test_set_range_round_rate_higher),
+	KUNIT_CASE(clk_range_test_set_range_set_rate_higher),
+	KUNIT_CASE(clk_range_test_set_range_set_round_rate_consistent_higher),
+	KUNIT_CASE(clk_range_test_set_range_get_rate_raised),
+	KUNIT_CASE(clk_range_test_set_range_get_rate_lowered),
+	{}
+};
+
+static struct kunit_suite clk_range_test_suite = {
+	.name = "clk-range-test",
+	.init = clk_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_range_test_cases,
+};
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range();
+ * - and we have a round_rate ops that always return the maximum
+ *   frequency allowed;
+ *
+ * The clock will run at the minimum of all maximum boundaries
+ * requested, even if those boundaries aren't there anymore.
+ */
+static void clk_range_test_set_range_rate_maximized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2 - 1000),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 - 1000);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 - 1000);
+}
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range(), across
+ *   multiple users;
+ * - and we have a round_rate ops that always return the maximum
+ *   frequency allowed;
+ *
+ * The clock will run at the minimum of all maximum boundaries
+ * requested, even if those boundaries aren't there anymore.
+ */
+static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	struct clk *user1, *user2;
+	unsigned long rate;
+
+	user1 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user1);
+
+	user2 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user1,
+					   0,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2,
+					   0,
+					   DUMMY_CLOCK_RATE_1),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2, 0, ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	clk_put(user2);
+	clk_put(user1);
+}
+
+static struct kunit_case clk_range_maximize_test_cases[] = {
+	KUNIT_CASE(clk_range_test_set_range_rate_maximized),
+	KUNIT_CASE(clk_range_test_multiple_set_range_rate_maximized),
+	{}
+};
+
+static struct kunit_suite clk_range_maximize_test_suite = {
+	.name = "clk-range-maximize-test",
+	.init = clk_maximize_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_range_maximize_test_cases,
+};
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range()
+ * - and we have a round_rate ops that always return the minimum
+ *   frequency allowed;
+ *
+ * The clock will run at the maximum of all minimum boundaries
+ * requested, even if those boundaries aren't there anymore.
+*/
+static void clk_range_test_set_range_rate_minimized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	unsigned long rate;
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
+			0);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1 + 1000,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 + 1000);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(clk,
+					   DUMMY_CLOCK_RATE_1,
+					   DUMMY_CLOCK_RATE_2),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 + 1000);
+}
+
+/*
+ * Test that if:
+ * - we have several subsequent calls to clk_set_rate_range(), across
+ *   multiple users;
+ * - and we have a round_rate ops that always return the minimum
+ *   frequency allowed;
+ *
+ * The clock will run at the maximum of all minimum boundaries
+ * requested, even if those boundaries aren't there anymore.
+*/
+static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
+{
+	struct clk_dummy_context *ctx = test->priv;
+	struct clk_hw *hw = &ctx->hw;
+	struct clk *clk = hw->clk;
+	struct clk *user1, *user2;
+	unsigned long rate;
+
+	user1 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user1);
+
+	user2 = clk_hw_get_clk(hw, NULL);
+	KUNIT_ASSERT_NOT_ERR_OR_NULL(test, user2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user1,
+					   DUMMY_CLOCK_RATE_1,
+					   ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2,
+					   DUMMY_CLOCK_RATE_2,
+					   ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	KUNIT_ASSERT_EQ(test,
+			clk_set_rate_range(user2, 0, ULONG_MAX),
+			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+
+	clk_put(user2);
+	clk_put(user1);
+}
+
+static struct kunit_case clk_range_minimize_test_cases[] = {
+	KUNIT_CASE(clk_range_test_set_range_rate_minimized),
+	KUNIT_CASE(clk_range_test_multiple_set_range_rate_minimized),
+	{}
+};
+
+static struct kunit_suite clk_range_minimize_test_suite = {
+	.name = "clk-range-minimize-test",
+	.init = clk_minimize_test_init,
+	.exit = clk_test_exit,
+	.test_cases = clk_range_minimize_test_cases,
+};
+
+kunit_test_suites(
+	&clk_test_suite,
+	&clk_range_test_suite,
+	&clk_range_maximize_test_suite,
+	&clk_range_minimize_test_suite
+);
+MODULE_LICENSE("GPL v2");
-- 
2.35.1

[PATCH v7 03/12] clk: Enforce that disjoints limits are invalid

[Maxime Ripard]

If we were to have two users of the same clock, doing something like:

clk_set_rate_range(user1, 1000, 2000);
clk_set_rate_range(user2, 3000, 4000);

The second call would fail with -EINVAL, preventing from getting in a
situation where we end up with impossible limits.

However, this is never explicitly checked against and enforced, and
works by relying on an undocumented behaviour of clk_set_rate().

Indeed, on the first clk_set_rate_range will make sure the current clock
rate is within the new range, so it will be between 1000 and 2000Hz. On
the second clk_set_rate_range(), it will consider (rightfully), that our
current clock is outside of the 3000-4000Hz range, and will call
clk_core_set_rate_nolock() to set it to 3000Hz.

clk_core_set_rate_nolock() will then call clk_calc_new_rates() that will
eventually check that our rate 3000Hz rate is outside the min 3000Hz max
2000Hz range, will bail out, the error will propagate and we'll
eventually return -EINVAL.

This solely relies on the fact that clk_calc_new_rates(), and in
particular clk_core_determine_round_nolock(), won't modify the new rate
allowing the error to be reported. That assumption won't be true for all
drivers, and most importantly we'll break that assumption in a later
patch.

It can also be argued that we shouldn't even reach the point where we're
calling clk_core_set_rate_nolock().

Let's make an explicit check for disjoints range before we're doing
anything.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index fff5edb89d6d..112911138a7b 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -632,6 +632,24 @@ static void clk_core_get_boundaries(struct clk_core *core,
 		*max_rate = min(*max_rate, clk_user->max_rate);
 }
 
+static bool clk_core_check_boundaries(struct clk_core *core,
+				      unsigned long min_rate,
+				      unsigned long max_rate)
+{
+	struct clk *user;
+
+	lockdep_assert_held(&prepare_lock);
+
+	if (min_rate > core->max_rate || max_rate < core->min_rate)
+		return false;
+
+	hlist_for_each_entry(user, &core->clks, clks_node)
+		if (min_rate > user->max_rate || max_rate < user->min_rate)
+			return false;
+
+	return true;
+}
+
 void clk_hw_set_rate_range(struct clk_hw *hw, unsigned long min_rate,
 			   unsigned long max_rate)
 {
@@ -2348,6 +2366,11 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 	clk->min_rate = min;
 	clk->max_rate = max;
 
+	if (!clk_core_check_boundaries(clk->core, min, max)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	rate = clk_core_get_rate_nolock(clk->core);
 	if (rate < min || rate > max) {
 		/*
@@ -2376,6 +2399,7 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 		}
 	}
 
+out:
 	if (clk->exclusive_count)
 		clk_core_rate_protect(clk->core);
 
-- 
2.35.1

[PATCH v7 03/12] clk: Enforce that disjoints limits are invalid

[Maxime Ripard]

If we were to have two users of the same clock, doing something like:

clk_set_rate_range(user1, 1000, 2000);
clk_set_rate_range(user2, 3000, 4000);

The second call would fail with -EINVAL, preventing from getting in a
situation where we end up with impossible limits.

However, this is never explicitly checked against and enforced, and
works by relying on an undocumented behaviour of clk_set_rate().

Indeed, on the first clk_set_rate_range will make sure the current clock
rate is within the new range, so it will be between 1000 and 2000Hz. On
the second clk_set_rate_range(), it will consider (rightfully), that our
current clock is outside of the 3000-4000Hz range, and will call
clk_core_set_rate_nolock() to set it to 3000Hz.

clk_core_set_rate_nolock() will then call clk_calc_new_rates() that will
eventually check that our rate 3000Hz rate is outside the min 3000Hz max
2000Hz range, will bail out, the error will propagate and we'll
eventually return -EINVAL.

This solely relies on the fact that clk_calc_new_rates(), and in
particular clk_core_determine_round_nolock(), won't modify the new rate
allowing the error to be reported. That assumption won't be true for all
drivers, and most importantly we'll break that assumption in a later
patch.

It can also be argued that we shouldn't even reach the point where we're
calling clk_core_set_rate_nolock().

Let's make an explicit check for disjoints range before we're doing
anything.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c | 24 ++++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index fff5edb89d6d..112911138a7b 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -632,6 +632,24 @@ static void clk_core_get_boundaries(struct clk_core *core,
 		*max_rate = min(*max_rate, clk_user->max_rate);
 }
 
+static bool clk_core_check_boundaries(struct clk_core *core,
+				      unsigned long min_rate,
+				      unsigned long max_rate)
+{
+	struct clk *user;
+
+	lockdep_assert_held(&prepare_lock);
+
+	if (min_rate > core->max_rate || max_rate < core->min_rate)
+		return false;
+
+	hlist_for_each_entry(user, &core->clks, clks_node)
+		if (min_rate > user->max_rate || max_rate < user->min_rate)
+			return false;
+
+	return true;
+}
+
 void clk_hw_set_rate_range(struct clk_hw *hw, unsigned long min_rate,
 			   unsigned long max_rate)
 {
@@ -2348,6 +2366,11 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 	clk->min_rate = min;
 	clk->max_rate = max;
 
+	if (!clk_core_check_boundaries(clk->core, min, max)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	rate = clk_core_get_rate_nolock(clk->core);
 	if (rate < min || rate > max) {
 		/*
@@ -2376,6 +2399,7 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 		}
 	}
 
+out:
 	if (clk->exclusive_count)
 		clk_core_rate_protect(clk->core);
 
-- 
2.35.1

[PATCH v7 04/12] clk: Always clamp the rounded rate

[Maxime Ripard]

The current core while setting the min and max rate properly in the
clk_request structure will not make sure that the requested rate is
within these boundaries, leaving it to each and every driver to make
sure it is.

It's not clear if this was on purpose or not, but this introduces some
inconsistencies within the API.

For example, a user setting a range and then calling clk_round_rate()
with a value outside of that range will get the same value back
(ignoring any driver adjustements), effectively ignoring the range that
was just set.

Another one, arguably worse, is that it also makes clk_round_rate() and
clk_set_rate() behave differently if there's a range and the rate being
used for both is outside that range. As we have seen, the rate will be
returned unchanged by clk_round_rate(), but clk_set_rate() will error
out returning -EINVAL.

Let's make sure the framework will always clamp the rate to the current
range found on the clock, which will fix both these inconsistencies.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c      |  2 ++
 drivers/clk/clk_test.c | 50 +++++++++++++++++++++++++++---------------
 2 files changed, 34 insertions(+), 18 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 112911138a7b..6c4e10209568 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -1348,6 +1348,8 @@ static int clk_core_determine_round_nolock(struct clk_core *core,
 	if (!core)
 		return 0;
 
+	req->rate = clamp(req->rate, req->min_rate, req->max_rate);
+
 	/*
 	 * At this point, core protection will be disabled
 	 * - if the provider is not protected at all
diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
index a8d7eba01de7..2279be699001 100644
--- a/drivers/clk/clk_test.c
+++ b/drivers/clk/clk_test.c
@@ -310,8 +310,7 @@ static void clk_range_test_multiple_disjoints_range(struct kunit *test)
 
 /*
  * Test that if our clock has some boundaries and we try to round a rate
- * lower than the minimum, the returned rate won't be affected by the
- * boundaries.
+ * lower than the minimum, the returned rate will be within range.
  */
 static void clk_range_test_set_range_round_rate_lower(struct kunit *test)
 {
@@ -328,18 +327,20 @@ static void clk_range_test_set_range_round_rate_lower(struct kunit *test)
 
 	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 - 1000);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to set a rate
- * lower than the minimum, we'll get an error.
+ * higher than the maximum, the new rate will be within range.
  */
 static void clk_range_test_set_range_set_rate_lower(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
 	struct clk_hw *hw = &ctx->hw;
 	struct clk *clk = hw->clk;
+	unsigned long rate;
 
 	KUNIT_ASSERT_EQ(test,
 			clk_set_rate_range(clk,
@@ -347,15 +348,21 @@ static void clk_range_test_set_range_set_rate_lower(struct kunit *test)
 					   DUMMY_CLOCK_RATE_2),
 			0);
 
-	KUNIT_ASSERT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
 			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to round and
- * set a rate lower than the minimum, the values won't be consistent
- * between clk_round_rate() and clk_set_rate().
+ * set a rate lower than the minimum, the rate returned by
+ * clk_round_rate() will be consistent with the new rate set by
+ * clk_set_rate().
  */
 static void clk_range_test_set_range_set_round_rate_consistent_lower(struct kunit *test)
 {
@@ -373,17 +380,16 @@ static void clk_range_test_set_range_set_round_rate_consistent_lower(struct kuni
 	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
 	KUNIT_ASSERT_GT(test, rounded, 0);
 
-	KUNIT_EXPECT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
 			0);
 
-	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+	KUNIT_EXPECT_EQ(test, rounded, clk_get_rate(clk));
 }
 
 /*
  * Test that if our clock has some boundaries and we try to round a rate
- * higher than the maximum, the returned rate won't be affected by the
- * boundaries.
+ * higher than the maximum, the returned rate will be within range.
  */
 static void clk_range_test_set_range_round_rate_higher(struct kunit *test)
 {
@@ -400,18 +406,20 @@ static void clk_range_test_set_range_round_rate_higher(struct kunit *test)
 
 	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 + 1000);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to set a rate
- * lower than the maximum, we'll get an error.
+ * higher than the maximum, the new rate will be within range.
  */
 static void clk_range_test_set_range_set_rate_higher(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
 	struct clk_hw *hw = &ctx->hw;
 	struct clk *clk = hw->clk;
+	unsigned long rate;
 
 	KUNIT_ASSERT_EQ(test,
 			clk_set_rate_range(clk,
@@ -419,15 +427,21 @@ static void clk_range_test_set_range_set_rate_higher(struct kunit *test)
 					   DUMMY_CLOCK_RATE_2),
 			0);
 
-	KUNIT_ASSERT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
 			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to round and
- * set a rate higher than the maximum, the values won't be consistent
- * between clk_round_rate() and clk_set_rate().
+ * set a rate higher than the maximum, the rate returned by
+ * clk_round_rate() will be consistent with the new rate set by
+ * clk_set_rate().
  */
 static void clk_range_test_set_range_set_round_rate_consistent_higher(struct kunit *test)
 {
@@ -445,11 +459,11 @@ static void clk_range_test_set_range_set_round_rate_consistent_higher(struct kun
 	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
 	KUNIT_ASSERT_GT(test, rounded, 0);
 
-	KUNIT_EXPECT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
 			0);
 
-	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+	KUNIT_EXPECT_EQ(test, rounded, clk_get_rate(clk));
 }
 
 /*
-- 
2.35.1

[PATCH v7 04/12] clk: Always clamp the rounded rate

[Maxime Ripard]

The current core while setting the min and max rate properly in the
clk_request structure will not make sure that the requested rate is
within these boundaries, leaving it to each and every driver to make
sure it is.

It's not clear if this was on purpose or not, but this introduces some
inconsistencies within the API.

For example, a user setting a range and then calling clk_round_rate()
with a value outside of that range will get the same value back
(ignoring any driver adjustements), effectively ignoring the range that
was just set.

Another one, arguably worse, is that it also makes clk_round_rate() and
clk_set_rate() behave differently if there's a range and the rate being
used for both is outside that range. As we have seen, the rate will be
returned unchanged by clk_round_rate(), but clk_set_rate() will error
out returning -EINVAL.

Let's make sure the framework will always clamp the rate to the current
range found on the clock, which will fix both these inconsistencies.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c      |  2 ++
 drivers/clk/clk_test.c | 50 +++++++++++++++++++++++++++---------------
 2 files changed, 34 insertions(+), 18 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 112911138a7b..6c4e10209568 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -1348,6 +1348,8 @@ static int clk_core_determine_round_nolock(struct clk_core *core,
 	if (!core)
 		return 0;
 
+	req->rate = clamp(req->rate, req->min_rate, req->max_rate);
+
 	/*
 	 * At this point, core protection will be disabled
 	 * - if the provider is not protected at all
diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
index a8d7eba01de7..2279be699001 100644
--- a/drivers/clk/clk_test.c
+++ b/drivers/clk/clk_test.c
@@ -310,8 +310,7 @@ static void clk_range_test_multiple_disjoints_range(struct kunit *test)
 
 /*
  * Test that if our clock has some boundaries and we try to round a rate
- * lower than the minimum, the returned rate won't be affected by the
- * boundaries.
+ * lower than the minimum, the returned rate will be within range.
  */
 static void clk_range_test_set_range_round_rate_lower(struct kunit *test)
 {
@@ -328,18 +327,20 @@ static void clk_range_test_set_range_round_rate_lower(struct kunit *test)
 
 	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 - 1000);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to set a rate
- * lower than the minimum, we'll get an error.
+ * higher than the maximum, the new rate will be within range.
  */
 static void clk_range_test_set_range_set_rate_lower(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
 	struct clk_hw *hw = &ctx->hw;
 	struct clk *clk = hw->clk;
+	unsigned long rate;
 
 	KUNIT_ASSERT_EQ(test,
 			clk_set_rate_range(clk,
@@ -347,15 +348,21 @@ static void clk_range_test_set_range_set_rate_lower(struct kunit *test)
 					   DUMMY_CLOCK_RATE_2),
 			0);
 
-	KUNIT_ASSERT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
 			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to round and
- * set a rate lower than the minimum, the values won't be consistent
- * between clk_round_rate() and clk_set_rate().
+ * set a rate lower than the minimum, the rate returned by
+ * clk_round_rate() will be consistent with the new rate set by
+ * clk_set_rate().
  */
 static void clk_range_test_set_range_set_round_rate_consistent_lower(struct kunit *test)
 {
@@ -373,17 +380,16 @@ static void clk_range_test_set_range_set_round_rate_consistent_lower(struct kuni
 	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_1 - 1000);
 	KUNIT_ASSERT_GT(test, rounded, 0);
 
-	KUNIT_EXPECT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_1 - 1000),
 			0);
 
-	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+	KUNIT_EXPECT_EQ(test, rounded, clk_get_rate(clk));
 }
 
 /*
  * Test that if our clock has some boundaries and we try to round a rate
- * higher than the maximum, the returned rate won't be affected by the
- * boundaries.
+ * higher than the maximum, the returned rate will be within range.
  */
 static void clk_range_test_set_range_round_rate_higher(struct kunit *test)
 {
@@ -400,18 +406,20 @@ static void clk_range_test_set_range_round_rate_higher(struct kunit *test)
 
 	rate = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 + 1000);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to set a rate
- * lower than the maximum, we'll get an error.
+ * higher than the maximum, the new rate will be within range.
  */
 static void clk_range_test_set_range_set_rate_higher(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
 	struct clk_hw *hw = &ctx->hw;
 	struct clk *clk = hw->clk;
+	unsigned long rate;
 
 	KUNIT_ASSERT_EQ(test,
 			clk_set_rate_range(clk,
@@ -419,15 +427,21 @@ static void clk_range_test_set_range_set_rate_higher(struct kunit *test)
 					   DUMMY_CLOCK_RATE_2),
 			0);
 
-	KUNIT_ASSERT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
 			0);
+
+	rate = clk_get_rate(clk);
+	KUNIT_ASSERT_GT(test, rate, 0);
+	KUNIT_EXPECT_GE(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_LE(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
  * Test that if our clock has some boundaries and we try to round and
- * set a rate higher than the maximum, the values won't be consistent
- * between clk_round_rate() and clk_set_rate().
+ * set a rate higher than the maximum, the rate returned by
+ * clk_round_rate() will be consistent with the new rate set by
+ * clk_set_rate().
  */
 static void clk_range_test_set_range_set_round_rate_consistent_higher(struct kunit *test)
 {
@@ -445,11 +459,11 @@ static void clk_range_test_set_range_set_round_rate_consistent_higher(struct kun
 	rounded = clk_round_rate(clk, DUMMY_CLOCK_RATE_2 + 1000);
 	KUNIT_ASSERT_GT(test, rounded, 0);
 
-	KUNIT_EXPECT_LT(test,
+	KUNIT_ASSERT_EQ(test,
 			clk_set_rate(clk, DUMMY_CLOCK_RATE_2 + 1000),
 			0);
 
-	KUNIT_EXPECT_NE(test, rounded, clk_get_rate(clk));
+	KUNIT_EXPECT_EQ(test, rounded, clk_get_rate(clk));
 }
 
 /*
-- 
2.35.1

[PATCH v7 05/12] clk: Use clamp instead of open-coding our own

[Maxime Ripard]

The code in clk_set_rate_range() will, if the current rate is outside of
the new range, force it to the minimum or maximum.

Since it's running under the condition that the rate is either lower
than the minimum, or higher than the maximum, this is equivalent to
using clamp, while being less readable. Let's switch to using clamp
instead.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 6c4e10209568..c15ee5070f52 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -2388,11 +2388,7 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 		 *   this corner case when determining the rate
 		 */
 
-		if (rate < min)
-			rate = min;
-		else
-			rate = max;
-
+		rate = clamp(clk->core->req_rate, min, max);
 		ret = clk_core_set_rate_nolock(clk->core, rate);
 		if (ret) {
 			/* rollback the changes */
-- 
2.35.1

[PATCH v7 05/12] clk: Use clamp instead of open-coding our own

[Maxime Ripard]

The code in clk_set_rate_range() will, if the current rate is outside of
the new range, force it to the minimum or maximum.

Since it's running under the condition that the rate is either lower
than the minimum, or higher than the maximum, this is equivalent to
using clamp, while being less readable. Let's switch to using clamp
instead.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c | 6 +-----
 1 file changed, 1 insertion(+), 5 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 6c4e10209568..c15ee5070f52 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -2388,11 +2388,7 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 		 *   this corner case when determining the rate
 		 */
 
-		if (rate < min)
-			rate = min;
-		else
-			rate = max;
-
+		rate = clamp(clk->core->req_rate, min, max);
 		ret = clk_core_set_rate_nolock(clk->core, rate);
 		if (ret) {
 			/* rollback the changes */
-- 
2.35.1

[PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Maxime Ripard]

When we change a clock minimum or maximum using clk_set_rate_range(),
clk_set_min_rate() or clk_set_max_rate(), the current code will only
trigger a new rate change if the rate is outside of the new boundaries.

However, a clock driver might want to always keep the clock rate to
one of its boundary, for example the minimum to keep the power
consumption as low as possible.

Since they don't always get called though, clock providers don't have the
opportunity to implement this behaviour.

Let's trigger a clk_set_rate() on the previous requested rate every time
clk_set_rate_range() is called. That way, providers that care about the
new boundaries have a chance to adjust the rate, while providers that
don't care about those new boundaries will return the same rate than
before, which will be ignored by clk_set_rate() and won't result in a
new rate change.

Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c      | 45 ++++++++++++++++----------------
 drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
 2 files changed, 49 insertions(+), 54 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index c15ee5070f52..9bc8bf434b94 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 		goto out;
 	}
 
-	rate = clk_core_get_rate_nolock(clk->core);
-	if (rate < min || rate > max) {
-		/*
-		 * FIXME:
-		 * We are in bit of trouble here, current rate is outside the
-		 * the requested range. We are going try to request appropriate
-		 * range boundary but there is a catch. It may fail for the
-		 * usual reason (clock broken, clock protected, etc) but also
-		 * because:
-		 * - round_rate() was not favorable and fell on the wrong
-		 *   side of the boundary
-		 * - the determine_rate() callback does not really check for
-		 *   this corner case when determining the rate
-		 */
-
-		rate = clamp(clk->core->req_rate, min, max);
-		ret = clk_core_set_rate_nolock(clk->core, rate);
-		if (ret) {
-			/* rollback the changes */
-			clk->min_rate = old_min;
-			clk->max_rate = old_max;
-		}
+	/*
+	 * Since the boundaries have been changed, let's give the
+	 * opportunity to the provider to adjust the clock rate based on
+	 * the new boundaries.
+	 *
+	 * We also need to handle the case where the clock is currently
+	 * outside of the boundaries. Clamping the last requested rate
+	 * to the current minimum and maximum will also handle this.
+	 *
+	 * FIXME:
+	 * There is a catch. It may fail for the usual reason (clock
+	 * broken, clock protected, etc) but also because:
+	 * - round_rate() was not favorable and fell on the wrong
+	 *   side of the boundary
+	 * - the determine_rate() callback does not really check for
+	 *   this corner case when determining the rate
+	 */
+	rate = clamp(clk->core->req_rate, min, max);
+	ret = clk_core_set_rate_nolock(clk->core, rate);
+	if (ret) {
+		/* rollback the changes */
+		clk->min_rate = old_min;
+		clk->max_rate = old_max;
 	}
 
 out:
diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
index 2279be699001..2c5d30a9372e 100644
--- a/drivers/clk/clk_test.c
+++ b/drivers/clk/clk_test.c
@@ -549,13 +549,12 @@ static struct kunit_suite clk_range_test_suite = {
 };
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range();
- * - and we have a round_rate ops that always return the maximum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), the core will reevaluate whether a new rate is
+ * needed each and every time.
  *
- * The clock will run at the minimum of all maximum boundaries
- * requested, even if those boundaries aren't there anymore.
+ * With clk_dummy_maximize_rate_ops, this means that the the rate will
+ * trail along the maximum as it evolves.
  */
 static void clk_range_test_set_range_rate_maximized(struct kunit *test)
 {
@@ -596,18 +595,16 @@ static void clk_range_test_set_range_rate_maximized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 - 1000);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range(), across
- *   multiple users;
- * - and we have a round_rate ops that always return the maximum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), across multiple users, the core will reevaluate
+ * whether a new rate is needed each and every time.
  *
- * The clock will run at the minimum of all maximum boundaries
- * requested, even if those boundaries aren't there anymore.
+ * With clk_dummy_maximize_rate_ops, this means that the the rate will
+ * trail along the maximum as it evolves.
  */
 static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
 {
@@ -653,7 +650,7 @@ static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
 
 	clk_put(user2);
 	clk_put(user1);
@@ -673,14 +670,13 @@ static struct kunit_suite clk_range_maximize_test_suite = {
 };
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range()
- * - and we have a round_rate ops that always return the minimum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), the core will reevaluate whether a new rate is
+ * needed each and every time.
  *
- * The clock will run at the maximum of all minimum boundaries
- * requested, even if those boundaries aren't there anymore.
-*/
+ * With clk_dummy_minimize_rate_ops, this means that the the rate will
+ * trail along the minimum as it evolves.
+ */
 static void clk_range_test_set_range_rate_minimized(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
@@ -720,19 +716,17 @@ static void clk_range_test_set_range_rate_minimized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 + 1000);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
 }
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range(), across
- *   multiple users;
- * - and we have a round_rate ops that always return the minimum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), across multiple users, the core will reevaluate
+ * whether a new rate is needed each and every time.
  *
- * The clock will run at the maximum of all minimum boundaries
- * requested, even if those boundaries aren't there anymore.
-*/
+ * With clk_dummy_minimize_rate_ops, this means that the the rate will
+ * trail along the minimum as it evolves.
+ */
 static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
@@ -773,7 +767,7 @@ static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
 
 	clk_put(user2);
 	clk_put(user1);
-- 
2.35.1

[PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Maxime Ripard]

When we change a clock minimum or maximum using clk_set_rate_range(),
clk_set_min_rate() or clk_set_max_rate(), the current code will only
trigger a new rate change if the rate is outside of the new boundaries.

However, a clock driver might want to always keep the clock rate to
one of its boundary, for example the minimum to keep the power
consumption as low as possible.

Since they don't always get called though, clock providers don't have the
opportunity to implement this behaviour.

Let's trigger a clk_set_rate() on the previous requested rate every time
clk_set_rate_range() is called. That way, providers that care about the
new boundaries have a chance to adjust the rate, while providers that
don't care about those new boundaries will return the same rate than
before, which will be ignored by clk_set_rate() and won't result in a
new rate change.

Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk.c      | 45 ++++++++++++++++----------------
 drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
 2 files changed, 49 insertions(+), 54 deletions(-)

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index c15ee5070f52..9bc8bf434b94 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
 		goto out;
 	}
 
-	rate = clk_core_get_rate_nolock(clk->core);
-	if (rate < min || rate > max) {
-		/*
-		 * FIXME:
-		 * We are in bit of trouble here, current rate is outside the
-		 * the requested range. We are going try to request appropriate
-		 * range boundary but there is a catch. It may fail for the
-		 * usual reason (clock broken, clock protected, etc) but also
-		 * because:
-		 * - round_rate() was not favorable and fell on the wrong
-		 *   side of the boundary
-		 * - the determine_rate() callback does not really check for
-		 *   this corner case when determining the rate
-		 */
-
-		rate = clamp(clk->core->req_rate, min, max);
-		ret = clk_core_set_rate_nolock(clk->core, rate);
-		if (ret) {
-			/* rollback the changes */
-			clk->min_rate = old_min;
-			clk->max_rate = old_max;
-		}
+	/*
+	 * Since the boundaries have been changed, let's give the
+	 * opportunity to the provider to adjust the clock rate based on
+	 * the new boundaries.
+	 *
+	 * We also need to handle the case where the clock is currently
+	 * outside of the boundaries. Clamping the last requested rate
+	 * to the current minimum and maximum will also handle this.
+	 *
+	 * FIXME:
+	 * There is a catch. It may fail for the usual reason (clock
+	 * broken, clock protected, etc) but also because:
+	 * - round_rate() was not favorable and fell on the wrong
+	 *   side of the boundary
+	 * - the determine_rate() callback does not really check for
+	 *   this corner case when determining the rate
+	 */
+	rate = clamp(clk->core->req_rate, min, max);
+	ret = clk_core_set_rate_nolock(clk->core, rate);
+	if (ret) {
+		/* rollback the changes */
+		clk->min_rate = old_min;
+		clk->max_rate = old_max;
 	}
 
 out:
diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
index 2279be699001..2c5d30a9372e 100644
--- a/drivers/clk/clk_test.c
+++ b/drivers/clk/clk_test.c
@@ -549,13 +549,12 @@ static struct kunit_suite clk_range_test_suite = {
 };
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range();
- * - and we have a round_rate ops that always return the maximum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), the core will reevaluate whether a new rate is
+ * needed each and every time.
  *
- * The clock will run at the minimum of all maximum boundaries
- * requested, even if those boundaries aren't there anymore.
+ * With clk_dummy_maximize_rate_ops, this means that the the rate will
+ * trail along the maximum as it evolves.
  */
 static void clk_range_test_set_range_rate_maximized(struct kunit *test)
 {
@@ -596,18 +595,16 @@ static void clk_range_test_set_range_rate_maximized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2 - 1000);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
 }
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range(), across
- *   multiple users;
- * - and we have a round_rate ops that always return the maximum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), across multiple users, the core will reevaluate
+ * whether a new rate is needed each and every time.
  *
- * The clock will run at the minimum of all maximum boundaries
- * requested, even if those boundaries aren't there anymore.
+ * With clk_dummy_maximize_rate_ops, this means that the the rate will
+ * trail along the maximum as it evolves.
  */
 static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
 {
@@ -653,7 +650,7 @@ static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
 
 	clk_put(user2);
 	clk_put(user1);
@@ -673,14 +670,13 @@ static struct kunit_suite clk_range_maximize_test_suite = {
 };
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range()
- * - and we have a round_rate ops that always return the minimum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), the core will reevaluate whether a new rate is
+ * needed each and every time.
  *
- * The clock will run at the maximum of all minimum boundaries
- * requested, even if those boundaries aren't there anymore.
-*/
+ * With clk_dummy_minimize_rate_ops, this means that the the rate will
+ * trail along the minimum as it evolves.
+ */
 static void clk_range_test_set_range_rate_minimized(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
@@ -720,19 +716,17 @@ static void clk_range_test_set_range_rate_minimized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1 + 1000);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
 }
 
 /*
- * Test that if:
- * - we have several subsequent calls to clk_set_rate_range(), across
- *   multiple users;
- * - and we have a round_rate ops that always return the minimum
- *   frequency allowed;
+ * Test that if we have several subsequent calls to
+ * clk_set_rate_range(), across multiple users, the core will reevaluate
+ * whether a new rate is needed each and every time.
  *
- * The clock will run at the maximum of all minimum boundaries
- * requested, even if those boundaries aren't there anymore.
-*/
+ * With clk_dummy_minimize_rate_ops, this means that the the rate will
+ * trail along the minimum as it evolves.
+ */
 static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
 {
 	struct clk_dummy_context *ctx = test->priv;
@@ -773,7 +767,7 @@ static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
 
 	rate = clk_get_rate(clk);
 	KUNIT_ASSERT_GT(test, rate, 0);
-	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
+	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
 
 	clk_put(user2);
 	clk_put(user1);
-- 
2.35.1

[PATCH v7 07/12] clk: Add clk_drop_range

[Maxime Ripard]

In order to reset the range on a clock, we need to call
clk_set_rate_range with a minimum of 0 and a maximum of ULONG_MAX. Since
it's fairly inconvenient, let's introduce a clk_drop_range() function
that will do just this.

Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk_test.c |  4 ++--
 include/linux/clk.h    | 11 +++++++++++
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
index 2c5d30a9372e..a92600311506 100644
--- a/drivers/clk/clk_test.c
+++ b/drivers/clk/clk_test.c
@@ -645,7 +645,7 @@ static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
 	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
 
 	KUNIT_ASSERT_EQ(test,
-			clk_set_rate_range(user2, 0, ULONG_MAX),
+			clk_drop_range(user2),
 			0);
 
 	rate = clk_get_rate(clk);
@@ -762,7 +762,7 @@ static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
 	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
 
 	KUNIT_ASSERT_EQ(test,
-			clk_set_rate_range(user2, 0, ULONG_MAX),
+			clk_drop_range(user2),
 			0);
 
 	rate = clk_get_rate(clk);
diff --git a/include/linux/clk.h b/include/linux/clk.h
index 266e8de3cb51..39faa54efe88 100644
--- a/include/linux/clk.h
+++ b/include/linux/clk.h
@@ -986,6 +986,17 @@ static inline void clk_bulk_disable_unprepare(int num_clks,
 	clk_bulk_unprepare(num_clks, clks);
 }
 
+/**
+ * clk_drop_range - Reset any range set on that clock
+ * @clk: clock source
+ *
+ * Returns success (0) or negative errno.
+ */
+static inline int clk_drop_range(struct clk *clk)
+{
+	return clk_set_rate_range(clk, 0, ULONG_MAX);
+}
+
 /**
  * clk_get_optional - lookup and obtain a reference to an optional clock
  *		      producer.
-- 
2.35.1

[PATCH v7 07/12] clk: Add clk_drop_range

[Maxime Ripard]

In order to reset the range on a clock, we need to call
clk_set_rate_range with a minimum of 0 and a maximum of ULONG_MAX. Since
it's fairly inconvenient, let's introduce a clk_drop_range() function
that will do just this.

Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/clk_test.c |  4 ++--
 include/linux/clk.h    | 11 +++++++++++
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/clk_test.c b/drivers/clk/clk_test.c
index 2c5d30a9372e..a92600311506 100644
--- a/drivers/clk/clk_test.c
+++ b/drivers/clk/clk_test.c
@@ -645,7 +645,7 @@ static void clk_range_test_multiple_set_range_rate_maximized(struct kunit *test)
 	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_1);
 
 	KUNIT_ASSERT_EQ(test,
-			clk_set_rate_range(user2, 0, ULONG_MAX),
+			clk_drop_range(user2),
 			0);
 
 	rate = clk_get_rate(clk);
@@ -762,7 +762,7 @@ static void clk_range_test_multiple_set_range_rate_minimized(struct kunit *test)
 	KUNIT_EXPECT_EQ(test, rate, DUMMY_CLOCK_RATE_2);
 
 	KUNIT_ASSERT_EQ(test,
-			clk_set_rate_range(user2, 0, ULONG_MAX),
+			clk_drop_range(user2),
 			0);
 
 	rate = clk_get_rate(clk);
diff --git a/include/linux/clk.h b/include/linux/clk.h
index 266e8de3cb51..39faa54efe88 100644
--- a/include/linux/clk.h
+++ b/include/linux/clk.h
@@ -986,6 +986,17 @@ static inline void clk_bulk_disable_unprepare(int num_clks,
 	clk_bulk_unprepare(num_clks, clks);
 }
 
+/**
+ * clk_drop_range - Reset any range set on that clock
+ * @clk: clock source
+ *
+ * Returns success (0) or negative errno.
+ */
+static inline int clk_drop_range(struct clk *clk)
+{
+	return clk_set_rate_range(clk, 0, ULONG_MAX);
+}
+
 /**
  * clk_get_optional - lookup and obtain a reference to an optional clock
  *		      producer.
-- 
2.35.1

[PATCH v7 08/12] clk: bcm: rpi: Add variant structure

[Maxime Ripard]

We only export a bunch of firmware clocks, and some of them require
special treatment.

This has been do so far using some tests on the clock id in various
places, but this is fairly hard to extend and doesn't scale very well.

Since we'll need some more cases in the next patches, let's switch to a
variant structure that defines the behaviour we need to have for a given
clock.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/bcm/clk-raspberrypi.c | 62 +++++++++++++++++++++++--------
 1 file changed, 46 insertions(+), 16 deletions(-)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index dd3b71eafabf..f7185d421085 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -56,6 +56,8 @@ static char *rpi_firmware_clk_names[] = {
 #define RPI_FIRMWARE_STATE_ENABLE_BIT	BIT(0)
 #define RPI_FIRMWARE_STATE_WAIT_BIT	BIT(1)
 
+struct raspberrypi_clk_variant;
+
 struct raspberrypi_clk {
 	struct device *dev;
 	struct rpi_firmware *firmware;
@@ -66,10 +68,36 @@ struct raspberrypi_clk_data {
 	struct clk_hw hw;
 
 	unsigned int id;
+	struct raspberrypi_clk_variant *variant;
 
 	struct raspberrypi_clk *rpi;
 };
 
+struct raspberrypi_clk_variant {
+	bool		export;
+	char		*clkdev;
+};
+
+static struct raspberrypi_clk_variant
+raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
+	[RPI_FIRMWARE_ARM_CLK_ID] = {
+		.export = true,
+		.clkdev = "cpu0",
+	},
+	[RPI_FIRMWARE_CORE_CLK_ID] = {
+		.export = true,
+	},
+	[RPI_FIRMWARE_M2MC_CLK_ID] = {
+		.export = true,
+	},
+	[RPI_FIRMWARE_V3D_CLK_ID] = {
+		.export = true,
+	},
+	[RPI_FIRMWARE_PIXEL_BVB_CLK_ID] = {
+		.export = true,
+	},
+};
+
 /*
  * Structure of the message passed to Raspberry Pi's firmware in order to
  * change clock rates. The 'disable_turbo' option is only available to the ARM
@@ -183,7 +211,8 @@ static const struct clk_ops raspberrypi_firmware_clk_ops = {
 
 static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 					       unsigned int parent,
-					       unsigned int id)
+					       unsigned int id,
+					       struct raspberrypi_clk_variant *variant)
 {
 	struct raspberrypi_clk_data *data;
 	struct clk_init_data init = {};
@@ -195,6 +224,7 @@ static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 		return ERR_PTR(-ENOMEM);
 	data->rpi = rpi;
 	data->id = id;
+	data->variant = variant;
 
 	init.name = devm_kasprintf(rpi->dev, GFP_KERNEL,
 				   "fw-clk-%s",
@@ -228,9 +258,9 @@ static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 
 	clk_hw_set_rate_range(&data->hw, min_rate, max_rate);
 
-	if (id == RPI_FIRMWARE_ARM_CLK_ID) {
+	if (variant->clkdev) {
 		ret = devm_clk_hw_register_clkdev(rpi->dev, &data->hw,
-						  NULL, "cpu0");
+						  NULL, variant->clkdev);
 		if (ret) {
 			dev_err(rpi->dev, "Failed to initialize clkdev\n");
 			return ERR_PTR(ret);
@@ -264,27 +294,27 @@ static int raspberrypi_discover_clocks(struct raspberrypi_clk *rpi,
 		return ret;
 
 	while (clks->id) {
-		struct clk_hw *hw;
+		struct raspberrypi_clk_variant *variant;
+
+		if (clks->id > RPI_FIRMWARE_NUM_CLK_ID) {
+			dev_err(rpi->dev, "Unknown clock id: %u", clks->id);
+			return -EINVAL;
+		}
+
+		variant = &raspberrypi_clk_variants[clks->id];
+		if (variant->export) {
+			struct clk_hw *hw;
 
-		switch (clks->id) {
-		case RPI_FIRMWARE_ARM_CLK_ID:
-		case RPI_FIRMWARE_CORE_CLK_ID:
-		case RPI_FIRMWARE_M2MC_CLK_ID:
-		case RPI_FIRMWARE_V3D_CLK_ID:
-		case RPI_FIRMWARE_PIXEL_BVB_CLK_ID:
 			hw = raspberrypi_clk_register(rpi, clks->parent,
-						      clks->id);
+						      clks->id, variant);
 			if (IS_ERR(hw))
 				return PTR_ERR(hw);
 
 			data->hws[clks->id] = hw;
 			data->num = clks->id + 1;
-			fallthrough;
-
-		default:
-			clks++;
-			break;
 		}
+
+		clks++;
 	}
 
 	return 0;
-- 
2.35.1

[PATCH v7 08/12] clk: bcm: rpi: Add variant structure

[Maxime Ripard]

We only export a bunch of firmware clocks, and some of them require
special treatment.

This has been do so far using some tests on the clock id in various
places, but this is fairly hard to extend and doesn't scale very well.

Since we'll need some more cases in the next patches, let's switch to a
variant structure that defines the behaviour we need to have for a given
clock.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/bcm/clk-raspberrypi.c | 62 +++++++++++++++++++++++--------
 1 file changed, 46 insertions(+), 16 deletions(-)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index dd3b71eafabf..f7185d421085 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -56,6 +56,8 @@ static char *rpi_firmware_clk_names[] = {
 #define RPI_FIRMWARE_STATE_ENABLE_BIT	BIT(0)
 #define RPI_FIRMWARE_STATE_WAIT_BIT	BIT(1)
 
+struct raspberrypi_clk_variant;
+
 struct raspberrypi_clk {
 	struct device *dev;
 	struct rpi_firmware *firmware;
@@ -66,10 +68,36 @@ struct raspberrypi_clk_data {
 	struct clk_hw hw;
 
 	unsigned int id;
+	struct raspberrypi_clk_variant *variant;
 
 	struct raspberrypi_clk *rpi;
 };
 
+struct raspberrypi_clk_variant {
+	bool		export;
+	char		*clkdev;
+};
+
+static struct raspberrypi_clk_variant
+raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
+	[RPI_FIRMWARE_ARM_CLK_ID] = {
+		.export = true,
+		.clkdev = "cpu0",
+	},
+	[RPI_FIRMWARE_CORE_CLK_ID] = {
+		.export = true,
+	},
+	[RPI_FIRMWARE_M2MC_CLK_ID] = {
+		.export = true,
+	},
+	[RPI_FIRMWARE_V3D_CLK_ID] = {
+		.export = true,
+	},
+	[RPI_FIRMWARE_PIXEL_BVB_CLK_ID] = {
+		.export = true,
+	},
+};
+
 /*
  * Structure of the message passed to Raspberry Pi's firmware in order to
  * change clock rates. The 'disable_turbo' option is only available to the ARM
@@ -183,7 +211,8 @@ static const struct clk_ops raspberrypi_firmware_clk_ops = {
 
 static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 					       unsigned int parent,
-					       unsigned int id)
+					       unsigned int id,
+					       struct raspberrypi_clk_variant *variant)
 {
 	struct raspberrypi_clk_data *data;
 	struct clk_init_data init = {};
@@ -195,6 +224,7 @@ static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 		return ERR_PTR(-ENOMEM);
 	data->rpi = rpi;
 	data->id = id;
+	data->variant = variant;
 
 	init.name = devm_kasprintf(rpi->dev, GFP_KERNEL,
 				   "fw-clk-%s",
@@ -228,9 +258,9 @@ static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 
 	clk_hw_set_rate_range(&data->hw, min_rate, max_rate);
 
-	if (id == RPI_FIRMWARE_ARM_CLK_ID) {
+	if (variant->clkdev) {
 		ret = devm_clk_hw_register_clkdev(rpi->dev, &data->hw,
-						  NULL, "cpu0");
+						  NULL, variant->clkdev);
 		if (ret) {
 			dev_err(rpi->dev, "Failed to initialize clkdev\n");
 			return ERR_PTR(ret);
@@ -264,27 +294,27 @@ static int raspberrypi_discover_clocks(struct raspberrypi_clk *rpi,
 		return ret;
 
 	while (clks->id) {
-		struct clk_hw *hw;
+		struct raspberrypi_clk_variant *variant;
+
+		if (clks->id > RPI_FIRMWARE_NUM_CLK_ID) {
+			dev_err(rpi->dev, "Unknown clock id: %u", clks->id);
+			return -EINVAL;
+		}
+
+		variant = &raspberrypi_clk_variants[clks->id];
+		if (variant->export) {
+			struct clk_hw *hw;
 
-		switch (clks->id) {
-		case RPI_FIRMWARE_ARM_CLK_ID:
-		case RPI_FIRMWARE_CORE_CLK_ID:
-		case RPI_FIRMWARE_M2MC_CLK_ID:
-		case RPI_FIRMWARE_V3D_CLK_ID:
-		case RPI_FIRMWARE_PIXEL_BVB_CLK_ID:
 			hw = raspberrypi_clk_register(rpi, clks->parent,
-						      clks->id);
+						      clks->id, variant);
 			if (IS_ERR(hw))
 				return PTR_ERR(hw);
 
 			data->hws[clks->id] = hw;
 			data->num = clks->id + 1;
-			fallthrough;
-
-		default:
-			clks++;
-			break;
 		}
+
+		clks++;
 	}
 
 	return 0;
-- 
2.35.1

[PATCH v7 09/12] clk: bcm: rpi: Set a default minimum rate

[Maxime Ripard]

The M2MC clock provides the state machine clock for both HDMI
controllers.

However, if no HDMI monitor is plugged in at boot, its clock rate will
be left at 0 by the firmware and will make any register access end up in
a CPU stall, even though the clock was enabled.

We had some code in the HDMI controller to deal with this before, but it
makes more sense to have it in the clock driver. Move it there.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/bcm/clk-raspberrypi.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index f7185d421085..c879f2e9a4a7 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -76,6 +76,7 @@ struct raspberrypi_clk_data {
 struct raspberrypi_clk_variant {
 	bool		export;
 	char		*clkdev;
+	unsigned long	min_rate;
 };
 
 static struct raspberrypi_clk_variant
@@ -89,6 +90,18 @@ raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
 	},
 	[RPI_FIRMWARE_M2MC_CLK_ID] = {
 		.export = true,
+
+		/*
+		 * If we boot without any cable connected to any of the
+		 * HDMI connector, the firmware will skip the HSM
+		 * initialization and leave it with a rate of 0,
+		 * resulting in a bus lockup when we're accessing the
+		 * registers even if it's enabled.
+		 *
+		 * Let's put a sensible default so that we don't end up
+		 * in this situation.
+		 */
+		.min_rate = 120000000,
 	},
 	[RPI_FIRMWARE_V3D_CLK_ID] = {
 		.export = true,
@@ -267,6 +280,19 @@ static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 		}
 	}
 
+	if (variant->min_rate) {
+		unsigned long rate;
+
+		clk_hw_set_rate_range(&data->hw, variant->min_rate, max_rate);
+
+		rate = raspberrypi_fw_get_rate(&data->hw, 0);
+		if (rate < variant->min_rate) {
+			ret = raspberrypi_fw_set_rate(&data->hw, variant->min_rate, 0);
+			if (ret)
+				return ERR_PTR(ret);
+		}
+	}
+
 	return &data->hw;
 }
 
-- 
2.35.1

[PATCH v7 09/12] clk: bcm: rpi: Set a default minimum rate

[Maxime Ripard]

The M2MC clock provides the state machine clock for both HDMI
controllers.

However, if no HDMI monitor is plugged in at boot, its clock rate will
be left at 0 by the firmware and will make any register access end up in
a CPU stall, even though the clock was enabled.

We had some code in the HDMI controller to deal with this before, but it
makes more sense to have it in the clock driver. Move it there.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/bcm/clk-raspberrypi.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index f7185d421085..c879f2e9a4a7 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -76,6 +76,7 @@ struct raspberrypi_clk_data {
 struct raspberrypi_clk_variant {
 	bool		export;
 	char		*clkdev;
+	unsigned long	min_rate;
 };
 
 static struct raspberrypi_clk_variant
@@ -89,6 +90,18 @@ raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
 	},
 	[RPI_FIRMWARE_M2MC_CLK_ID] = {
 		.export = true,
+
+		/*
+		 * If we boot without any cable connected to any of the
+		 * HDMI connector, the firmware will skip the HSM
+		 * initialization and leave it with a rate of 0,
+		 * resulting in a bus lockup when we're accessing the
+		 * registers even if it's enabled.
+		 *
+		 * Let's put a sensible default so that we don't end up
+		 * in this situation.
+		 */
+		.min_rate = 120000000,
 	},
 	[RPI_FIRMWARE_V3D_CLK_ID] = {
 		.export = true,
@@ -267,6 +280,19 @@ static struct clk_hw *raspberrypi_clk_register(struct raspberrypi_clk *rpi,
 		}
 	}
 
+	if (variant->min_rate) {
+		unsigned long rate;
+
+		clk_hw_set_rate_range(&data->hw, variant->min_rate, max_rate);
+
+		rate = raspberrypi_fw_get_rate(&data->hw, 0);
+		if (rate < variant->min_rate) {
+			ret = raspberrypi_fw_set_rate(&data->hw, variant->min_rate, 0);
+			if (ret)
+				return ERR_PTR(ret);
+		}
+	}
+
 	return &data->hw;
 }
 
-- 
2.35.1

[PATCH v7 10/12] clk: bcm: rpi: Run some clocks at the minimum rate allowed

[Maxime Ripard]

The core clock and M2MC clocks are shared between some devices (Unicam
controllers and the HVS, and the HDMI controllers, respectively) that
will have various, varying, requirements depending on their current work
load.

Since those loads can require a fairly high clock rate in extreme
conditions (up to ~600MHz), we can end up running those clocks at their
maximum frequency even though we no longer require such a high rate.

Fortunately, those devices don't require an exact rate but a minimum
rate, and all the drivers are using clk_set_min_rate. Thus, we can just
rely on the fact that the clk_request minimum (which is the aggregated
minimum of all the clock users) is what we want at all times.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/bcm/clk-raspberrypi.c | 37 +++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index c879f2e9a4a7..9d09621549b9 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -77,6 +77,7 @@ struct raspberrypi_clk_variant {
 	bool		export;
 	char		*clkdev;
 	unsigned long	min_rate;
+	bool		minimize;
 };
 
 static struct raspberrypi_clk_variant
@@ -87,6 +88,18 @@ raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
 	},
 	[RPI_FIRMWARE_CORE_CLK_ID] = {
 		.export = true,
+
+		/*
+		 * The clock is shared between the HVS and the CSI
+		 * controllers, on the BCM2711 and will change depending
+		 * on the pixels composited on the HVS and the capture
+		 * resolution on Unicam.
+		 *
+		 * Since the rate can get quite large, and we need to
+		 * coordinate between both driver instances, let's
+		 * always use the minimum the drivers will let us.
+		 */
+		.minimize = true,
 	},
 	[RPI_FIRMWARE_M2MC_CLK_ID] = {
 		.export = true,
@@ -102,6 +115,16 @@ raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
 		 * in this situation.
 		 */
 		.min_rate = 120000000,
+
+		/*
+		 * The clock is shared between the two HDMI controllers
+		 * on the BCM2711 and will change depending on the
+		 * resolution output on each. Since the rate can get
+		 * quite large, and we need to coordinate between both
+		 * driver instances, let's always use the minimum the
+		 * drivers will let us.
+		 */
+		.minimize = true,
 	},
 	[RPI_FIRMWARE_V3D_CLK_ID] = {
 		.export = true,
@@ -206,12 +229,26 @@ static int raspberrypi_fw_set_rate(struct clk_hw *hw, unsigned long rate,
 static int raspberrypi_fw_dumb_determine_rate(struct clk_hw *hw,
 					      struct clk_rate_request *req)
 {
+	struct raspberrypi_clk_data *data =
+		container_of(hw, struct raspberrypi_clk_data, hw);
+	struct raspberrypi_clk_variant *variant = data->variant;
+
 	/*
 	 * The firmware will do the rounding but that isn't part of
 	 * the interface with the firmware, so we just do our best
 	 * here.
 	 */
+
 	req->rate = clamp(req->rate, req->min_rate, req->max_rate);
+
+	/*
+	 * We want to aggressively reduce the clock rate here, so let's
+	 * just ignore the requested rate and return the bare minimum
+	 * rate we can get away with.
+	 */
+	if (variant->minimize && req->min_rate > 0)
+		req->rate = req->min_rate;
+
 	return 0;
 }
 
-- 
2.35.1

[PATCH v7 10/12] clk: bcm: rpi: Run some clocks at the minimum rate allowed

[Maxime Ripard]

The core clock and M2MC clocks are shared between some devices (Unicam
controllers and the HVS, and the HDMI controllers, respectively) that
will have various, varying, requirements depending on their current work
load.

Since those loads can require a fairly high clock rate in extreme
conditions (up to ~600MHz), we can end up running those clocks at their
maximum frequency even though we no longer require such a high rate.

Fortunately, those devices don't require an exact rate but a minimum
rate, and all the drivers are using clk_set_min_rate. Thus, we can just
rely on the fact that the clk_request minimum (which is the aggregated
minimum of all the clock users) is what we want at all times.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/clk/bcm/clk-raspberrypi.c | 37 +++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/drivers/clk/bcm/clk-raspberrypi.c b/drivers/clk/bcm/clk-raspberrypi.c
index c879f2e9a4a7..9d09621549b9 100644
--- a/drivers/clk/bcm/clk-raspberrypi.c
+++ b/drivers/clk/bcm/clk-raspberrypi.c
@@ -77,6 +77,7 @@ struct raspberrypi_clk_variant {
 	bool		export;
 	char		*clkdev;
 	unsigned long	min_rate;
+	bool		minimize;
 };
 
 static struct raspberrypi_clk_variant
@@ -87,6 +88,18 @@ raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
 	},
 	[RPI_FIRMWARE_CORE_CLK_ID] = {
 		.export = true,
+
+		/*
+		 * The clock is shared between the HVS and the CSI
+		 * controllers, on the BCM2711 and will change depending
+		 * on the pixels composited on the HVS and the capture
+		 * resolution on Unicam.
+		 *
+		 * Since the rate can get quite large, and we need to
+		 * coordinate between both driver instances, let's
+		 * always use the minimum the drivers will let us.
+		 */
+		.minimize = true,
 	},
 	[RPI_FIRMWARE_M2MC_CLK_ID] = {
 		.export = true,
@@ -102,6 +115,16 @@ raspberrypi_clk_variants[RPI_FIRMWARE_NUM_CLK_ID] = {
 		 * in this situation.
 		 */
 		.min_rate = 120000000,
+
+		/*
+		 * The clock is shared between the two HDMI controllers
+		 * on the BCM2711 and will change depending on the
+		 * resolution output on each. Since the rate can get
+		 * quite large, and we need to coordinate between both
+		 * driver instances, let's always use the minimum the
+		 * drivers will let us.
+		 */
+		.minimize = true,
 	},
 	[RPI_FIRMWARE_V3D_CLK_ID] = {
 		.export = true,
@@ -206,12 +229,26 @@ static int raspberrypi_fw_set_rate(struct clk_hw *hw, unsigned long rate,
 static int raspberrypi_fw_dumb_determine_rate(struct clk_hw *hw,
 					      struct clk_rate_request *req)
 {
+	struct raspberrypi_clk_data *data =
+		container_of(hw, struct raspberrypi_clk_data, hw);
+	struct raspberrypi_clk_variant *variant = data->variant;
+
 	/*
 	 * The firmware will do the rounding but that isn't part of
 	 * the interface with the firmware, so we just do our best
 	 * here.
 	 */
+
 	req->rate = clamp(req->rate, req->min_rate, req->max_rate);
+
+	/*
+	 * We want to aggressively reduce the clock rate here, so let's
+	 * just ignore the requested rate and return the bare minimum
+	 * rate we can get away with.
+	 */
+	if (variant->minimize && req->min_rate > 0)
+		req->rate = req->min_rate;
+
 	return 0;
 }
 
-- 
2.35.1

[PATCH v7 11/12] drm/vc4: Add logging and comments

[Maxime Ripard]

The HVS core clock isn't really obvious, so let's add a bunch more
comments and some logging for easier debugging.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/gpu/drm/vc4/vc4_kms.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 24de29bc1cda..6fe03fc17d73 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -389,8 +389,15 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 						500000000,
 						new_hvs_state->core_clock_rate);
 
+		drm_dbg(dev, "Raising the core clock at %lu Hz\n", core_rate);
+
+		/*
+		 * Do a temporary request on the core clock during the
+		 * modeset.
+		 */
 		clk_set_min_rate(hvs->core_clk, core_rate);
 	}
+
 	drm_atomic_helper_commit_modeset_disables(dev, state);
 
 	vc4_ctm_commit(vc4, state);
@@ -416,6 +423,10 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 		drm_dbg(dev, "Running the core clock at %lu Hz\n",
 			new_hvs_state->core_clock_rate);
 
+		/*
+		 * Request a clock rate based on the current HVS
+		 * requirements.
+		 */
 		clk_set_min_rate(hvs->core_clk, new_hvs_state->core_clock_rate);
 	}
 }
-- 
2.35.1

[PATCH v7 11/12] drm/vc4: Add logging and comments

[Maxime Ripard]

The HVS core clock isn't really obvious, so let's add a bunch more
comments and some logging for easier debugging.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/gpu/drm/vc4/vc4_kms.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index 24de29bc1cda..6fe03fc17d73 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -389,8 +389,15 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 						500000000,
 						new_hvs_state->core_clock_rate);
 
+		drm_dbg(dev, "Raising the core clock at %lu Hz\n", core_rate);
+
+		/*
+		 * Do a temporary request on the core clock during the
+		 * modeset.
+		 */
 		clk_set_min_rate(hvs->core_clk, core_rate);
 	}
+
 	drm_atomic_helper_commit_modeset_disables(dev, state);
 
 	vc4_ctm_commit(vc4, state);
@@ -416,6 +423,10 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 		drm_dbg(dev, "Running the core clock at %lu Hz\n",
 			new_hvs_state->core_clock_rate);
 
+		/*
+		 * Request a clock rate based on the current HVS
+		 * requirements.
+		 */
 		clk_set_min_rate(hvs->core_clk, new_hvs_state->core_clock_rate);
 	}
 }
-- 
2.35.1

[PATCH v7 12/12] drm/vc4: hdmi: Remove clock rate initialization

[Maxime Ripard]

Now that the clock driver makes sure we never end up with a rate of 0,
the HDMI driver doesn't need to care anymore.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/gpu/drm/vc4/vc4_hdmi.c | 13 -------------
 1 file changed, 13 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 92b1530aa17b..21aff3ad96cf 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -2576,19 +2576,6 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
 			vc4_hdmi->disable_4kp60 = true;
 	}
 
-	/*
-	 * If we boot without any cable connected to the HDMI connector,
-	 * the firmware will skip the HSM initialization and leave it
-	 * with a rate of 0, resulting in a bus lockup when we're
-	 * accessing the registers even if it's enabled.
-	 *
-	 * Let's put a sensible default at runtime_resume so that we
-	 * don't end up in this situation.
-	 */
-	ret = clk_set_min_rate(vc4_hdmi->hsm_clock, HSM_MIN_CLOCK_FREQ);
-	if (ret)
-		goto err_put_ddc;
-
 	/*
 	 * We need to have the device powered up at this point to call
 	 * our reset hook and for the CEC init.
-- 
2.35.1

[PATCH v7 12/12] drm/vc4: hdmi: Remove clock rate initialization

[Maxime Ripard]

Now that the clock driver makes sure we never end up with a rate of 0,
the HDMI driver doesn't need to care anymore.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 drivers/gpu/drm/vc4/vc4_hdmi.c | 13 -------------
 1 file changed, 13 deletions(-)

diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
index 92b1530aa17b..21aff3ad96cf 100644
--- a/drivers/gpu/drm/vc4/vc4_hdmi.c
+++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
@@ -2576,19 +2576,6 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
 			vc4_hdmi->disable_4kp60 = true;
 	}
 
-	/*
-	 * If we boot without any cable connected to the HDMI connector,
-	 * the firmware will skip the HSM initialization and leave it
-	 * with a rate of 0, resulting in a bus lockup when we're
-	 * accessing the registers even if it's enabled.
-	 *
-	 * Let's put a sensible default at runtime_resume so that we
-	 * don't end up in this situation.
-	 */
-	ret = clk_set_min_rate(vc4_hdmi->hsm_clock, HSM_MIN_CLOCK_FREQ);
-	if (ret)
-		goto err_put_ddc;
-
 	/*
 	 * We need to have the device powered up at this point to call
 	 * our reset hook and for the CEC init.
-- 
2.35.1

Re: [PATCH v7 00/12] clk: Improve clock range handling

[Stephen Boyd]

Quoting Maxime Ripard (2022-02-25 06:35:22)
> Hi,
> 
> This is a follow-up of the discussion here:
> https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/
> 
> and here:
> https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/
> 
> While the initial proposal implemented a new API to temporarily raise and lower
> clock rates based on consumer workloads, Stephen suggested an
> alternative approach implemented here.
> 
> The main issue that needed to be addressed in our case was that in a
> situation where we would have multiple calls to clk_set_rate_range, we
> would end up with a clock at the maximum of the minimums being set. This
> would be expected, but the issue was that if one of the users was to
> relax or drop its requirements, the rate would be left unchanged, even
> though the ideal rate would have changed.
> 
> So something like
> 
> clk_set_rate(user1_clk, 1000);
> clk_set_min_rate(user1_clk, 2000);
> clk_set_min_rate(user2_clk, 3000);
> clk_set_min_rate(user2_clk, 1000);
> 
> Would leave the clock running at 3000Hz, while the minimum would now be
> 2000Hz.
> 
> This was mostly due to the fact that the core only triggers a rate
> change in clk_set_rate_range() if the current rate is outside of the
> boundaries, but not if it's within the new boundaries.
> 
> That series changes that and will trigger a rate change on every call,
> with the former rate being tried again. This way, providers have a
> chance to follow whatever policy they see fit for a given clock each
> time the boundaries change.
> 
> This series also implements some kunit tests, first to test a few rate
> related functions in the CCF, and then extends it to make sure that
> behaviour has some test coverage.
> 
> Let me know what you think

Thanks. I'm going to apply this to clk-next but not the last two drm
patches. That is OK?

Re: [PATCH v7 00/12] clk: Improve clock range handling

[Stephen Boyd]

Quoting Maxime Ripard (2022-02-25 06:35:22)
> Hi,
> 
> This is a follow-up of the discussion here:
> https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/
> 
> and here:
> https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/
> 
> While the initial proposal implemented a new API to temporarily raise and lower
> clock rates based on consumer workloads, Stephen suggested an
> alternative approach implemented here.
> 
> The main issue that needed to be addressed in our case was that in a
> situation where we would have multiple calls to clk_set_rate_range, we
> would end up with a clock at the maximum of the minimums being set. This
> would be expected, but the issue was that if one of the users was to
> relax or drop its requirements, the rate would be left unchanged, even
> though the ideal rate would have changed.
> 
> So something like
> 
> clk_set_rate(user1_clk, 1000);
> clk_set_min_rate(user1_clk, 2000);
> clk_set_min_rate(user2_clk, 3000);
> clk_set_min_rate(user2_clk, 1000);
> 
> Would leave the clock running at 3000Hz, while the minimum would now be
> 2000Hz.
> 
> This was mostly due to the fact that the core only triggers a rate
> change in clk_set_rate_range() if the current rate is outside of the
> boundaries, but not if it's within the new boundaries.
> 
> That series changes that and will trigger a rate change on every call,
> with the former rate being tried again. This way, providers have a
> chance to follow whatever policy they see fit for a given clock each
> time the boundaries change.
> 
> This series also implements some kunit tests, first to test a few rate
> related functions in the CCF, and then extends it to make sure that
> behaviour has some test coverage.
> 
> Let me know what you think

Thanks. I'm going to apply this to clk-next but not the last two drm
patches. That is OK?

Re: [PATCH v7 00/12] clk: Improve clock range handling

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2129 bytes --]

Hi,

On Fri, Mar 11, 2022 at 07:08:39PM -0800, Stephen Boyd wrote:
> Quoting Maxime Ripard (2022-02-25 06:35:22)
> > Hi,
> > 
> > This is a follow-up of the discussion here:
> > https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/
> > 
> > and here:
> > https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/
> > 
> > While the initial proposal implemented a new API to temporarily raise and lower
> > clock rates based on consumer workloads, Stephen suggested an
> > alternative approach implemented here.
> > 
> > The main issue that needed to be addressed in our case was that in a
> > situation where we would have multiple calls to clk_set_rate_range, we
> > would end up with a clock at the maximum of the minimums being set. This
> > would be expected, but the issue was that if one of the users was to
> > relax or drop its requirements, the rate would be left unchanged, even
> > though the ideal rate would have changed.
> > 
> > So something like
> > 
> > clk_set_rate(user1_clk, 1000);
> > clk_set_min_rate(user1_clk, 2000);
> > clk_set_min_rate(user2_clk, 3000);
> > clk_set_min_rate(user2_clk, 1000);
> > 
> > Would leave the clock running at 3000Hz, while the minimum would now be
> > 2000Hz.
> > 
> > This was mostly due to the fact that the core only triggers a rate
> > change in clk_set_rate_range() if the current rate is outside of the
> > boundaries, but not if it's within the new boundaries.
> > 
> > That series changes that and will trigger a rate change on every call,
> > with the former rate being tried again. This way, providers have a
> > chance to follow whatever policy they see fit for a given clock each
> > time the boundaries change.
> > 
> > This series also implements some kunit tests, first to test a few rate
> > related functions in the CCF, and then extends it to make sure that
> > behaviour has some test coverage.
> > 
> > Let me know what you think
> 
> Thanks. I'm going to apply this to clk-next but not the last two drm
> patches. That is OK?

Yes, that will be perfect, thanks!
Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v7 00/12] clk: Improve clock range handling

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2129 bytes --]

Hi,

On Fri, Mar 11, 2022 at 07:08:39PM -0800, Stephen Boyd wrote:
> Quoting Maxime Ripard (2022-02-25 06:35:22)
> > Hi,
> > 
> > This is a follow-up of the discussion here:
> > https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/
> > 
> > and here:
> > https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/
> > 
> > While the initial proposal implemented a new API to temporarily raise and lower
> > clock rates based on consumer workloads, Stephen suggested an
> > alternative approach implemented here.
> > 
> > The main issue that needed to be addressed in our case was that in a
> > situation where we would have multiple calls to clk_set_rate_range, we
> > would end up with a clock at the maximum of the minimums being set. This
> > would be expected, but the issue was that if one of the users was to
> > relax or drop its requirements, the rate would be left unchanged, even
> > though the ideal rate would have changed.
> > 
> > So something like
> > 
> > clk_set_rate(user1_clk, 1000);
> > clk_set_min_rate(user1_clk, 2000);
> > clk_set_min_rate(user2_clk, 3000);
> > clk_set_min_rate(user2_clk, 1000);
> > 
> > Would leave the clock running at 3000Hz, while the minimum would now be
> > 2000Hz.
> > 
> > This was mostly due to the fact that the core only triggers a rate
> > change in clk_set_rate_range() if the current rate is outside of the
> > boundaries, but not if it's within the new boundaries.
> > 
> > That series changes that and will trigger a rate change on every call,
> > with the former rate being tried again. This way, providers have a
> > chance to follow whatever policy they see fit for a given clock each
> > time the boundaries change.
> > 
> > This series also implements some kunit tests, first to test a few rate
> > related functions in the CCF, and then extends it to make sure that
> > behaviour has some test coverage.
> > 
> > Let me know what you think
> 
> Thanks. I'm going to apply this to clk-next but not the last two drm
> patches. That is OK?

Yes, that will be perfect, thanks!
Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Dmitry Osipenko]

On 2/25/22 17:35, Maxime Ripard wrote:
> When we change a clock minimum or maximum using clk_set_rate_range(),
> clk_set_min_rate() or clk_set_max_rate(), the current code will only
> trigger a new rate change if the rate is outside of the new boundaries.
> 
> However, a clock driver might want to always keep the clock rate to
> one of its boundary, for example the minimum to keep the power
> consumption as low as possible.
> 
> Since they don't always get called though, clock providers don't have the
> opportunity to implement this behaviour.
> 
> Let's trigger a clk_set_rate() on the previous requested rate every time
> clk_set_rate_range() is called. That way, providers that care about the
> new boundaries have a chance to adjust the rate, while providers that
> don't care about those new boundaries will return the same rate than
> before, which will be ignored by clk_set_rate() and won't result in a
> new rate change.
> 
> Suggested-by: Stephen Boyd <sboyd@kernel.org>
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> ---
>  drivers/clk/clk.c      | 45 ++++++++++++++++----------------
>  drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
>  2 files changed, 49 insertions(+), 54 deletions(-)
> 
> diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
> index c15ee5070f52..9bc8bf434b94 100644
> --- a/drivers/clk/clk.c
> +++ b/drivers/clk/clk.c
> @@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
>  		goto out;
>  	}
>  
> -	rate = clk_core_get_rate_nolock(clk->core);
> -	if (rate < min || rate > max) {
> -		/*
> -		 * FIXME:
> -		 * We are in bit of trouble here, current rate is outside the
> -		 * the requested range. We are going try to request appropriate
> -		 * range boundary but there is a catch. It may fail for the
> -		 * usual reason (clock broken, clock protected, etc) but also
> -		 * because:
> -		 * - round_rate() was not favorable and fell on the wrong
> -		 *   side of the boundary
> -		 * - the determine_rate() callback does not really check for
> -		 *   this corner case when determining the rate
> -		 */
> -
> -		rate = clamp(clk->core->req_rate, min, max);
> -		ret = clk_core_set_rate_nolock(clk->core, rate);
> -		if (ret) {
> -			/* rollback the changes */
> -			clk->min_rate = old_min;
> -			clk->max_rate = old_max;
> -		}
> +	/*
> +	 * Since the boundaries have been changed, let's give the
> +	 * opportunity to the provider to adjust the clock rate based on
> +	 * the new boundaries.
> +	 *
> +	 * We also need to handle the case where the clock is currently
> +	 * outside of the boundaries. Clamping the last requested rate
> +	 * to the current minimum and maximum will also handle this.
> +	 *
> +	 * FIXME:
> +	 * There is a catch. It may fail for the usual reason (clock
> +	 * broken, clock protected, etc) but also because:
> +	 * - round_rate() was not favorable and fell on the wrong
> +	 *   side of the boundary
> +	 * - the determine_rate() callback does not really check for
> +	 *   this corner case when determining the rate
> +	 */
> +	rate = clamp(clk->core->req_rate, min, max);
> +	ret = clk_core_set_rate_nolock(clk->core, rate);
> +	if (ret) {
> +		/* rollback the changes */
> +		clk->min_rate = old_min;
> +		clk->max_rate = old_max;
>  	}
>  
>  out:

Hi,

NVIDIA Tegra30 no longer boots with this change.

You can't assume that rate was requested by clk_set_rate() before
clk_set_rate_range() is called, see what [1] does. T30 memory rate now
drops to min on boot when clk debug range is inited innocuously and CPU
no longer can make any progress because display controller takes out
whole memory bandwidth.

[1]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/memory/tegra/tegra30-emc.c#n1437

If clk_set_rate() wasn't ever invoked and req_rate=0, then you must not
change the clk rate if it's within the new range. Please revert this
patch, thanks.

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Dmitry Osipenko]

On 2/25/22 17:35, Maxime Ripard wrote:
> When we change a clock minimum or maximum using clk_set_rate_range(),
> clk_set_min_rate() or clk_set_max_rate(), the current code will only
> trigger a new rate change if the rate is outside of the new boundaries.
> 
> However, a clock driver might want to always keep the clock rate to
> one of its boundary, for example the minimum to keep the power
> consumption as low as possible.
> 
> Since they don't always get called though, clock providers don't have the
> opportunity to implement this behaviour.
> 
> Let's trigger a clk_set_rate() on the previous requested rate every time
> clk_set_rate_range() is called. That way, providers that care about the
> new boundaries have a chance to adjust the rate, while providers that
> don't care about those new boundaries will return the same rate than
> before, which will be ignored by clk_set_rate() and won't result in a
> new rate change.
> 
> Suggested-by: Stephen Boyd <sboyd@kernel.org>
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> ---
>  drivers/clk/clk.c      | 45 ++++++++++++++++----------------
>  drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
>  2 files changed, 49 insertions(+), 54 deletions(-)
> 
> diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
> index c15ee5070f52..9bc8bf434b94 100644
> --- a/drivers/clk/clk.c
> +++ b/drivers/clk/clk.c
> @@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
>  		goto out;
>  	}
>  
> -	rate = clk_core_get_rate_nolock(clk->core);
> -	if (rate < min || rate > max) {
> -		/*
> -		 * FIXME:
> -		 * We are in bit of trouble here, current rate is outside the
> -		 * the requested range. We are going try to request appropriate
> -		 * range boundary but there is a catch. It may fail for the
> -		 * usual reason (clock broken, clock protected, etc) but also
> -		 * because:
> -		 * - round_rate() was not favorable and fell on the wrong
> -		 *   side of the boundary
> -		 * - the determine_rate() callback does not really check for
> -		 *   this corner case when determining the rate
> -		 */
> -
> -		rate = clamp(clk->core->req_rate, min, max);
> -		ret = clk_core_set_rate_nolock(clk->core, rate);
> -		if (ret) {
> -			/* rollback the changes */
> -			clk->min_rate = old_min;
> -			clk->max_rate = old_max;
> -		}
> +	/*
> +	 * Since the boundaries have been changed, let's give the
> +	 * opportunity to the provider to adjust the clock rate based on
> +	 * the new boundaries.
> +	 *
> +	 * We also need to handle the case where the clock is currently
> +	 * outside of the boundaries. Clamping the last requested rate
> +	 * to the current minimum and maximum will also handle this.
> +	 *
> +	 * FIXME:
> +	 * There is a catch. It may fail for the usual reason (clock
> +	 * broken, clock protected, etc) but also because:
> +	 * - round_rate() was not favorable and fell on the wrong
> +	 *   side of the boundary
> +	 * - the determine_rate() callback does not really check for
> +	 *   this corner case when determining the rate
> +	 */
> +	rate = clamp(clk->core->req_rate, min, max);
> +	ret = clk_core_set_rate_nolock(clk->core, rate);
> +	if (ret) {
> +		/* rollback the changes */
> +		clk->min_rate = old_min;
> +		clk->max_rate = old_max;
>  	}
>  
>  out:

Hi,

NVIDIA Tegra30 no longer boots with this change.

You can't assume that rate was requested by clk_set_rate() before
clk_set_rate_range() is called, see what [1] does. T30 memory rate now
drops to min on boot when clk debug range is inited innocuously and CPU
no longer can make any progress because display controller takes out
whole memory bandwidth.

[1]
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/memory/tegra/tegra30-emc.c#n1437

If clk_set_rate() wasn't ever invoked and req_rate=0, then you must not
change the clk rate if it's within the new range. Please revert this
patch, thanks.

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 6199 bytes --]

Hi,

On Tue, Mar 22, 2022 at 10:05:56PM +0300, Dmitry Osipenko wrote:
> On 2/25/22 17:35, Maxime Ripard wrote:
> > When we change a clock minimum or maximum using clk_set_rate_range(),
> > clk_set_min_rate() or clk_set_max_rate(), the current code will only
> > trigger a new rate change if the rate is outside of the new boundaries.
> > 
> > However, a clock driver might want to always keep the clock rate to
> > one of its boundary, for example the minimum to keep the power
> > consumption as low as possible.
> > 
> > Since they don't always get called though, clock providers don't have the
> > opportunity to implement this behaviour.
> > 
> > Let's trigger a clk_set_rate() on the previous requested rate every time
> > clk_set_rate_range() is called. That way, providers that care about the
> > new boundaries have a chance to adjust the rate, while providers that
> > don't care about those new boundaries will return the same rate than
> > before, which will be ignored by clk_set_rate() and won't result in a
> > new rate change.
> > 
> > Suggested-by: Stephen Boyd <sboyd@kernel.org>
> > Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> > ---
> >  drivers/clk/clk.c      | 45 ++++++++++++++++----------------
> >  drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
> >  2 files changed, 49 insertions(+), 54 deletions(-)
> > 
> > diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
> > index c15ee5070f52..9bc8bf434b94 100644
> > --- a/drivers/clk/clk.c
> > +++ b/drivers/clk/clk.c
> > @@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
> >  		goto out;
> >  	}
> >  
> > -	rate = clk_core_get_rate_nolock(clk->core);
> > -	if (rate < min || rate > max) {
> > -		/*
> > -		 * FIXME:
> > -		 * We are in bit of trouble here, current rate is outside the
> > -		 * the requested range. We are going try to request appropriate
> > -		 * range boundary but there is a catch. It may fail for the
> > -		 * usual reason (clock broken, clock protected, etc) but also
> > -		 * because:
> > -		 * - round_rate() was not favorable and fell on the wrong
> > -		 *   side of the boundary
> > -		 * - the determine_rate() callback does not really check for
> > -		 *   this corner case when determining the rate
> > -		 */
> > -
> > -		rate = clamp(clk->core->req_rate, min, max);
> > -		ret = clk_core_set_rate_nolock(clk->core, rate);
> > -		if (ret) {
> > -			/* rollback the changes */
> > -			clk->min_rate = old_min;
> > -			clk->max_rate = old_max;
> > -		}
> > +	/*
> > +	 * Since the boundaries have been changed, let's give the
> > +	 * opportunity to the provider to adjust the clock rate based on
> > +	 * the new boundaries.
> > +	 *
> > +	 * We also need to handle the case where the clock is currently
> > +	 * outside of the boundaries. Clamping the last requested rate
> > +	 * to the current minimum and maximum will also handle this.
> > +	 *
> > +	 * FIXME:
> > +	 * There is a catch. It may fail for the usual reason (clock
> > +	 * broken, clock protected, etc) but also because:
> > +	 * - round_rate() was not favorable and fell on the wrong
> > +	 *   side of the boundary
> > +	 * - the determine_rate() callback does not really check for
> > +	 *   this corner case when determining the rate
> > +	 */
> > +	rate = clamp(clk->core->req_rate, min, max);
> > +	ret = clk_core_set_rate_nolock(clk->core, rate);
> > +	if (ret) {
> > +		/* rollback the changes */
> > +		clk->min_rate = old_min;
> > +		clk->max_rate = old_max;
> >  	}
> >  
> >  out:
>
> NVIDIA Tegra30 no longer boots with this change.
> 
> You can't assume that rate was requested by clk_set_rate() before
> clk_set_rate_range() is called, see what [1] does.

We don't, and it would be bad indeed.

We even have (multiple) tests to cover that case:
https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git/tree/drivers/clk/clk_test.c?h=clk-range&id=a9b269310ad9abb2f206fe814fd3afcadddce3aa#n242

> T30 memory rate now drops to min on boot when clk debug range is
> inited innocuously and CPU no longer can make any progress because
> display controller takes out whole memory bandwidth.
> 
> [1]
> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/memory/tegra/tegra30-emc.c#n1437
> 
> If clk_set_rate() wasn't ever invoked and req_rate=0, then you must not
> change the clk rate if it's within the new range. Please revert this
> patch, thanks.

The whole point of this patch is to give an opportunity to every driver
to change the rate whenever the boundaries have changed, so we very much
want to have the option to change it if clk_set_rate() has never been
called.

However, I think the issue is why req_rate would be 0 in the first
place?

req_rate is initialized to what recalc_rate returns:
https://elixir.bootlin.com/linux/latest/source/drivers/clk/clk.c#L3607

So the case where req_rate is 0 shouldn't occur unless you had an
explicit clk_set_rate to 0, or if your clock was orphaned at some point.

Judging from the code, it seems like the latter is the most plausible.
Indeed, __clk_core_init() will set req_rate to 0 if the clock is
orphaned (just like rate and accuracy), and
clk_core_reparent_orphans_nolock will be in charge of updating them when
the clock is no longer an orphan.

However, clk_core_reparent_orphans_nolock() will update rate by calling
__clk_recalc_rate and accuracy by calling __clk_recalc_accuracies, but
it never sets req_rate.

I'm not sure if this is the right patch, Stephen will tell, but could
you test:

------------------------ >8 ------------------------

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 9bc8bf434b94..c43340afedee 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -3479,6 +3479,7 @@ static void clk_core_reparent_orphans_nolock(void)
 			__clk_set_parent_after(orphan, parent, NULL);
 			__clk_recalc_accuracies(orphan);
 			__clk_recalc_rates(orphan, 0);
+			orphan->req_rate = orphan->rate;
 		}
 	}
 }

------------------------ >8 ------------------------

Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 6199 bytes --]

Hi,

On Tue, Mar 22, 2022 at 10:05:56PM +0300, Dmitry Osipenko wrote:
> On 2/25/22 17:35, Maxime Ripard wrote:
> > When we change a clock minimum or maximum using clk_set_rate_range(),
> > clk_set_min_rate() or clk_set_max_rate(), the current code will only
> > trigger a new rate change if the rate is outside of the new boundaries.
> > 
> > However, a clock driver might want to always keep the clock rate to
> > one of its boundary, for example the minimum to keep the power
> > consumption as low as possible.
> > 
> > Since they don't always get called though, clock providers don't have the
> > opportunity to implement this behaviour.
> > 
> > Let's trigger a clk_set_rate() on the previous requested rate every time
> > clk_set_rate_range() is called. That way, providers that care about the
> > new boundaries have a chance to adjust the rate, while providers that
> > don't care about those new boundaries will return the same rate than
> > before, which will be ignored by clk_set_rate() and won't result in a
> > new rate change.
> > 
> > Suggested-by: Stephen Boyd <sboyd@kernel.org>
> > Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> > ---
> >  drivers/clk/clk.c      | 45 ++++++++++++++++----------------
> >  drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
> >  2 files changed, 49 insertions(+), 54 deletions(-)
> > 
> > diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
> > index c15ee5070f52..9bc8bf434b94 100644
> > --- a/drivers/clk/clk.c
> > +++ b/drivers/clk/clk.c
> > @@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
> >  		goto out;
> >  	}
> >  
> > -	rate = clk_core_get_rate_nolock(clk->core);
> > -	if (rate < min || rate > max) {
> > -		/*
> > -		 * FIXME:
> > -		 * We are in bit of trouble here, current rate is outside the
> > -		 * the requested range. We are going try to request appropriate
> > -		 * range boundary but there is a catch. It may fail for the
> > -		 * usual reason (clock broken, clock protected, etc) but also
> > -		 * because:
> > -		 * - round_rate() was not favorable and fell on the wrong
> > -		 *   side of the boundary
> > -		 * - the determine_rate() callback does not really check for
> > -		 *   this corner case when determining the rate
> > -		 */
> > -
> > -		rate = clamp(clk->core->req_rate, min, max);
> > -		ret = clk_core_set_rate_nolock(clk->core, rate);
> > -		if (ret) {
> > -			/* rollback the changes */
> > -			clk->min_rate = old_min;
> > -			clk->max_rate = old_max;
> > -		}
> > +	/*
> > +	 * Since the boundaries have been changed, let's give the
> > +	 * opportunity to the provider to adjust the clock rate based on
> > +	 * the new boundaries.
> > +	 *
> > +	 * We also need to handle the case where the clock is currently
> > +	 * outside of the boundaries. Clamping the last requested rate
> > +	 * to the current minimum and maximum will also handle this.
> > +	 *
> > +	 * FIXME:
> > +	 * There is a catch. It may fail for the usual reason (clock
> > +	 * broken, clock protected, etc) but also because:
> > +	 * - round_rate() was not favorable and fell on the wrong
> > +	 *   side of the boundary
> > +	 * - the determine_rate() callback does not really check for
> > +	 *   this corner case when determining the rate
> > +	 */
> > +	rate = clamp(clk->core->req_rate, min, max);
> > +	ret = clk_core_set_rate_nolock(clk->core, rate);
> > +	if (ret) {
> > +		/* rollback the changes */
> > +		clk->min_rate = old_min;
> > +		clk->max_rate = old_max;
> >  	}
> >  
> >  out:
>
> NVIDIA Tegra30 no longer boots with this change.
> 
> You can't assume that rate was requested by clk_set_rate() before
> clk_set_rate_range() is called, see what [1] does.

We don't, and it would be bad indeed.

We even have (multiple) tests to cover that case:
https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git/tree/drivers/clk/clk_test.c?h=clk-range&id=a9b269310ad9abb2f206fe814fd3afcadddce3aa#n242

> T30 memory rate now drops to min on boot when clk debug range is
> inited innocuously and CPU no longer can make any progress because
> display controller takes out whole memory bandwidth.
> 
> [1]
> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/memory/tegra/tegra30-emc.c#n1437
> 
> If clk_set_rate() wasn't ever invoked and req_rate=0, then you must not
> change the clk rate if it's within the new range. Please revert this
> patch, thanks.

The whole point of this patch is to give an opportunity to every driver
to change the rate whenever the boundaries have changed, so we very much
want to have the option to change it if clk_set_rate() has never been
called.

However, I think the issue is why req_rate would be 0 in the first
place?

req_rate is initialized to what recalc_rate returns:
https://elixir.bootlin.com/linux/latest/source/drivers/clk/clk.c#L3607

So the case where req_rate is 0 shouldn't occur unless you had an
explicit clk_set_rate to 0, or if your clock was orphaned at some point.

Judging from the code, it seems like the latter is the most plausible.
Indeed, __clk_core_init() will set req_rate to 0 if the clock is
orphaned (just like rate and accuracy), and
clk_core_reparent_orphans_nolock will be in charge of updating them when
the clock is no longer an orphan.

However, clk_core_reparent_orphans_nolock() will update rate by calling
__clk_recalc_rate and accuracy by calling __clk_recalc_accuracies, but
it never sets req_rate.

I'm not sure if this is the right patch, Stephen will tell, but could
you test:

------------------------ >8 ------------------------

diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index 9bc8bf434b94..c43340afedee 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -3479,6 +3479,7 @@ static void clk_core_reparent_orphans_nolock(void)
 			__clk_set_parent_after(orphan, parent, NULL);
 			__clk_recalc_accuracies(orphan);
 			__clk_recalc_rates(orphan, 0);
+			orphan->req_rate = orphan->rate;
 		}
 	}
 }

------------------------ >8 ------------------------

Maxime

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Stephen Boyd]

Quoting Maxime Ripard (2022-03-23 01:51:40)
> Hi,
> 
> 
> The whole point of this patch is to give an opportunity to every driver
> to change the rate whenever the boundaries have changed, so we very much
> want to have the option to change it if clk_set_rate() has never been
> called.
> 
> However, I think the issue is why req_rate would be 0 in the first
> place?
> 
> req_rate is initialized to what recalc_rate returns:
> https://elixir.bootlin.com/linux/latest/source/drivers/clk/clk.c#L3607
> 
> So the case where req_rate is 0 shouldn't occur unless you had an
> explicit clk_set_rate to 0, or if your clock was orphaned at some point.
> 
> Judging from the code, it seems like the latter is the most plausible.
> Indeed, __clk_core_init() will set req_rate to 0 if the clock is
> orphaned (just like rate and accuracy), and
> clk_core_reparent_orphans_nolock will be in charge of updating them when
> the clock is no longer an orphan.
> 
> However, clk_core_reparent_orphans_nolock() will update rate by calling
> __clk_recalc_rate and accuracy by calling __clk_recalc_accuracies, but
> it never sets req_rate.
> 
> I'm not sure if this is the right patch, Stephen will tell, but could
> you test:

It looks correct to me. Would be helpful to have some comment of course
that we're setting a default req_rate because we want a
clk_set_rate_range() before clk_set_rate() to work properly when this
clk is initially an orphan. We should be able to code up a test case for
that too by registering an orphan and then registering the parent and
then calling clk_set_rate_range().

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Stephen Boyd]

Quoting Maxime Ripard (2022-03-23 01:51:40)
> Hi,
> 
> 
> The whole point of this patch is to give an opportunity to every driver
> to change the rate whenever the boundaries have changed, so we very much
> want to have the option to change it if clk_set_rate() has never been
> called.
> 
> However, I think the issue is why req_rate would be 0 in the first
> place?
> 
> req_rate is initialized to what recalc_rate returns:
> https://elixir.bootlin.com/linux/latest/source/drivers/clk/clk.c#L3607
> 
> So the case where req_rate is 0 shouldn't occur unless you had an
> explicit clk_set_rate to 0, or if your clock was orphaned at some point.
> 
> Judging from the code, it seems like the latter is the most plausible.
> Indeed, __clk_core_init() will set req_rate to 0 if the clock is
> orphaned (just like rate and accuracy), and
> clk_core_reparent_orphans_nolock will be in charge of updating them when
> the clock is no longer an orphan.
> 
> However, clk_core_reparent_orphans_nolock() will update rate by calling
> __clk_recalc_rate and accuracy by calling __clk_recalc_accuracies, but
> it never sets req_rate.
> 
> I'm not sure if this is the right patch, Stephen will tell, but could
> you test:

It looks correct to me. Would be helpful to have some comment of course
that we're setting a default req_rate because we want a
clk_set_rate_range() before clk_set_rate() to work properly when this
clk is initially an orphan. We should be able to code up a test case for
that too by registering an orphan and then registering the parent and
then calling clk_set_rate_range().

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Dmitry Osipenko]

On 3/23/22 11:51, Maxime Ripard wrote:
> Hi,
> 
> On Tue, Mar 22, 2022 at 10:05:56PM +0300, Dmitry Osipenko wrote:
>> On 2/25/22 17:35, Maxime Ripard wrote:
>>> When we change a clock minimum or maximum using clk_set_rate_range(),
>>> clk_set_min_rate() or clk_set_max_rate(), the current code will only
>>> trigger a new rate change if the rate is outside of the new boundaries.
>>>
>>> However, a clock driver might want to always keep the clock rate to
>>> one of its boundary, for example the minimum to keep the power
>>> consumption as low as possible.
>>>
>>> Since they don't always get called though, clock providers don't have the
>>> opportunity to implement this behaviour.
>>>
>>> Let's trigger a clk_set_rate() on the previous requested rate every time
>>> clk_set_rate_range() is called. That way, providers that care about the
>>> new boundaries have a chance to adjust the rate, while providers that
>>> don't care about those new boundaries will return the same rate than
>>> before, which will be ignored by clk_set_rate() and won't result in a
>>> new rate change.
>>>
>>> Suggested-by: Stephen Boyd <sboyd@kernel.org>
>>> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
>>> ---
>>>  drivers/clk/clk.c      | 45 ++++++++++++++++----------------
>>>  drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
>>>  2 files changed, 49 insertions(+), 54 deletions(-)
>>>
>>> diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
>>> index c15ee5070f52..9bc8bf434b94 100644
>>> --- a/drivers/clk/clk.c
>>> +++ b/drivers/clk/clk.c
>>> @@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
>>>  		goto out;
>>>  	}
>>>  
>>> -	rate = clk_core_get_rate_nolock(clk->core);
>>> -	if (rate < min || rate > max) {
>>> -		/*
>>> -		 * FIXME:
>>> -		 * We are in bit of trouble here, current rate is outside the
>>> -		 * the requested range. We are going try to request appropriate
>>> -		 * range boundary but there is a catch. It may fail for the
>>> -		 * usual reason (clock broken, clock protected, etc) but also
>>> -		 * because:
>>> -		 * - round_rate() was not favorable and fell on the wrong
>>> -		 *   side of the boundary
>>> -		 * - the determine_rate() callback does not really check for
>>> -		 *   this corner case when determining the rate
>>> -		 */
>>> -
>>> -		rate = clamp(clk->core->req_rate, min, max);
>>> -		ret = clk_core_set_rate_nolock(clk->core, rate);
>>> -		if (ret) {
>>> -			/* rollback the changes */
>>> -			clk->min_rate = old_min;
>>> -			clk->max_rate = old_max;
>>> -		}
>>> +	/*
>>> +	 * Since the boundaries have been changed, let's give the
>>> +	 * opportunity to the provider to adjust the clock rate based on
>>> +	 * the new boundaries.
>>> +	 *
>>> +	 * We also need to handle the case where the clock is currently
>>> +	 * outside of the boundaries. Clamping the last requested rate
>>> +	 * to the current minimum and maximum will also handle this.
>>> +	 *
>>> +	 * FIXME:
>>> +	 * There is a catch. It may fail for the usual reason (clock
>>> +	 * broken, clock protected, etc) but also because:
>>> +	 * - round_rate() was not favorable and fell on the wrong
>>> +	 *   side of the boundary
>>> +	 * - the determine_rate() callback does not really check for
>>> +	 *   this corner case when determining the rate
>>> +	 */
>>> +	rate = clamp(clk->core->req_rate, min, max);
>>> +	ret = clk_core_set_rate_nolock(clk->core, rate);
>>> +	if (ret) {
>>> +		/* rollback the changes */
>>> +		clk->min_rate = old_min;
>>> +		clk->max_rate = old_max;
>>>  	}
>>>  
>>>  out:
>>
>> NVIDIA Tegra30 no longer boots with this change.
>>
>> You can't assume that rate was requested by clk_set_rate() before
>> clk_set_rate_range() is called, see what [1] does.
> 
> We don't, and it would be bad indeed.
> 
> We even have (multiple) tests to cover that case:
> https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git/tree/drivers/clk/clk_test.c?h=clk-range&id=a9b269310ad9abb2f206fe814fd3afcadddce3aa#n242
> 
>> T30 memory rate now drops to min on boot when clk debug range is
>> inited innocuously and CPU no longer can make any progress because
>> display controller takes out whole memory bandwidth.
>>
>> [1]
>> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/memory/tegra/tegra30-emc.c#n1437
>>
>> If clk_set_rate() wasn't ever invoked and req_rate=0, then you must not
>> change the clk rate if it's within the new range. Please revert this
>> patch, thanks.
> 
> The whole point of this patch is to give an opportunity to every driver
> to change the rate whenever the boundaries have changed, so we very much
> want to have the option to change it if clk_set_rate() has never been
> called.
> 
> However, I think the issue is why req_rate would be 0 in the first
> place?
> 
> req_rate is initialized to what recalc_rate returns:
> https://elixir.bootlin.com/linux/latest/source/drivers/clk/clk.c#L3607
> 
> So the case where req_rate is 0 shouldn't occur unless you had an
> explicit clk_set_rate to 0, or if your clock was orphaned at some point.
> 
> Judging from the code, it seems like the latter is the most plausible.
> Indeed, __clk_core_init() will set req_rate to 0 if the clock is
> orphaned (just like rate and accuracy), and
> clk_core_reparent_orphans_nolock will be in charge of updating them when
> the clock is no longer an orphan.
> 
> However, clk_core_reparent_orphans_nolock() will update rate by calling
> __clk_recalc_rate and accuracy by calling __clk_recalc_accuracies, but
> it never sets req_rate.
> 
> I'm not sure if this is the right patch, Stephen will tell, but could
> you test:
> 
> ------------------------ >8 ------------------------
> 
> diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
> index 9bc8bf434b94..c43340afedee 100644
> --- a/drivers/clk/clk.c
> +++ b/drivers/clk/clk.c
> @@ -3479,6 +3479,7 @@ static void clk_core_reparent_orphans_nolock(void)
>  			__clk_set_parent_after(orphan, parent, NULL);
>  			__clk_recalc_accuracies(orphan);
>  			__clk_recalc_rates(orphan, 0);
> +			orphan->req_rate = orphan->rate;
>  		}
>  	}
>  }
> 
> ------------------------ >8 ------------------------

It works, thank you!

Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> # T30 Nexus7

Re: [PATCH v7 06/12] clk: Always set the rate on clk_set_range_rate

[Dmitry Osipenko]

On 3/23/22 11:51, Maxime Ripard wrote:
> Hi,
> 
> On Tue, Mar 22, 2022 at 10:05:56PM +0300, Dmitry Osipenko wrote:
>> On 2/25/22 17:35, Maxime Ripard wrote:
>>> When we change a clock minimum or maximum using clk_set_rate_range(),
>>> clk_set_min_rate() or clk_set_max_rate(), the current code will only
>>> trigger a new rate change if the rate is outside of the new boundaries.
>>>
>>> However, a clock driver might want to always keep the clock rate to
>>> one of its boundary, for example the minimum to keep the power
>>> consumption as low as possible.
>>>
>>> Since they don't always get called though, clock providers don't have the
>>> opportunity to implement this behaviour.
>>>
>>> Let's trigger a clk_set_rate() on the previous requested rate every time
>>> clk_set_rate_range() is called. That way, providers that care about the
>>> new boundaries have a chance to adjust the rate, while providers that
>>> don't care about those new boundaries will return the same rate than
>>> before, which will be ignored by clk_set_rate() and won't result in a
>>> new rate change.
>>>
>>> Suggested-by: Stephen Boyd <sboyd@kernel.org>
>>> Signed-off-by: Maxime Ripard <maxime@cerno.tech>
>>> ---
>>>  drivers/clk/clk.c      | 45 ++++++++++++++++----------------
>>>  drivers/clk/clk_test.c | 58 +++++++++++++++++++-----------------------
>>>  2 files changed, 49 insertions(+), 54 deletions(-)
>>>
>>> diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
>>> index c15ee5070f52..9bc8bf434b94 100644
>>> --- a/drivers/clk/clk.c
>>> +++ b/drivers/clk/clk.c
>>> @@ -2373,28 +2373,29 @@ int clk_set_rate_range(struct clk *clk, unsigned long min, unsigned long max)
>>>  		goto out;
>>>  	}
>>>  
>>> -	rate = clk_core_get_rate_nolock(clk->core);
>>> -	if (rate < min || rate > max) {
>>> -		/*
>>> -		 * FIXME:
>>> -		 * We are in bit of trouble here, current rate is outside the
>>> -		 * the requested range. We are going try to request appropriate
>>> -		 * range boundary but there is a catch. It may fail for the
>>> -		 * usual reason (clock broken, clock protected, etc) but also
>>> -		 * because:
>>> -		 * - round_rate() was not favorable and fell on the wrong
>>> -		 *   side of the boundary
>>> -		 * - the determine_rate() callback does not really check for
>>> -		 *   this corner case when determining the rate
>>> -		 */
>>> -
>>> -		rate = clamp(clk->core->req_rate, min, max);
>>> -		ret = clk_core_set_rate_nolock(clk->core, rate);
>>> -		if (ret) {
>>> -			/* rollback the changes */
>>> -			clk->min_rate = old_min;
>>> -			clk->max_rate = old_max;
>>> -		}
>>> +	/*
>>> +	 * Since the boundaries have been changed, let's give the
>>> +	 * opportunity to the provider to adjust the clock rate based on
>>> +	 * the new boundaries.
>>> +	 *
>>> +	 * We also need to handle the case where the clock is currently
>>> +	 * outside of the boundaries. Clamping the last requested rate
>>> +	 * to the current minimum and maximum will also handle this.
>>> +	 *
>>> +	 * FIXME:
>>> +	 * There is a catch. It may fail for the usual reason (clock
>>> +	 * broken, clock protected, etc) but also because:
>>> +	 * - round_rate() was not favorable and fell on the wrong
>>> +	 *   side of the boundary
>>> +	 * - the determine_rate() callback does not really check for
>>> +	 *   this corner case when determining the rate
>>> +	 */
>>> +	rate = clamp(clk->core->req_rate, min, max);
>>> +	ret = clk_core_set_rate_nolock(clk->core, rate);
>>> +	if (ret) {
>>> +		/* rollback the changes */
>>> +		clk->min_rate = old_min;
>>> +		clk->max_rate = old_max;
>>>  	}
>>>  
>>>  out:
>>
>> NVIDIA Tegra30 no longer boots with this change.
>>
>> You can't assume that rate was requested by clk_set_rate() before
>> clk_set_rate_range() is called, see what [1] does.
> 
> We don't, and it would be bad indeed.
> 
> We even have (multiple) tests to cover that case:
> https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git/tree/drivers/clk/clk_test.c?h=clk-range&id=a9b269310ad9abb2f206fe814fd3afcadddce3aa#n242
> 
>> T30 memory rate now drops to min on boot when clk debug range is
>> inited innocuously and CPU no longer can make any progress because
>> display controller takes out whole memory bandwidth.
>>
>> [1]
>> https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/memory/tegra/tegra30-emc.c#n1437
>>
>> If clk_set_rate() wasn't ever invoked and req_rate=0, then you must not
>> change the clk rate if it's within the new range. Please revert this
>> patch, thanks.
> 
> The whole point of this patch is to give an opportunity to every driver
> to change the rate whenever the boundaries have changed, so we very much
> want to have the option to change it if clk_set_rate() has never been
> called.
> 
> However, I think the issue is why req_rate would be 0 in the first
> place?
> 
> req_rate is initialized to what recalc_rate returns:
> https://elixir.bootlin.com/linux/latest/source/drivers/clk/clk.c#L3607
> 
> So the case where req_rate is 0 shouldn't occur unless you had an
> explicit clk_set_rate to 0, or if your clock was orphaned at some point.
> 
> Judging from the code, it seems like the latter is the most plausible.
> Indeed, __clk_core_init() will set req_rate to 0 if the clock is
> orphaned (just like rate and accuracy), and
> clk_core_reparent_orphans_nolock will be in charge of updating them when
> the clock is no longer an orphan.
> 
> However, clk_core_reparent_orphans_nolock() will update rate by calling
> __clk_recalc_rate and accuracy by calling __clk_recalc_accuracies, but
> it never sets req_rate.
> 
> I'm not sure if this is the right patch, Stephen will tell, but could
> you test:
> 
> ------------------------ >8 ------------------------
> 
> diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
> index 9bc8bf434b94..c43340afedee 100644
> --- a/drivers/clk/clk.c
> +++ b/drivers/clk/clk.c
> @@ -3479,6 +3479,7 @@ static void clk_core_reparent_orphans_nolock(void)
>  			__clk_set_parent_after(orphan, parent, NULL);
>  			__clk_recalc_accuracies(orphan);
>  			__clk_recalc_rates(orphan, 0);
> +			orphan->req_rate = orphan->rate;
>  		}
>  	}
>  }
> 
> ------------------------ >8 ------------------------

It works, thank you!

Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> # T30 Nexus7

Re: [PATCH v7 11/12] drm/vc4: Add logging and comments

[Thomas Zimmermann]

[-- Attachment #1.1: Type: text/plain, Size: 1650 bytes --]



Am 25.02.22 um 15:35 schrieb Maxime Ripard:
> The HVS core clock isn't really obvious, so let's add a bunch more
> comments and some logging for easier debugging.
> 
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>

> ---
>   drivers/gpu/drm/vc4/vc4_kms.c | 11 +++++++++++
>   1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
> index 24de29bc1cda..6fe03fc17d73 100644
> --- a/drivers/gpu/drm/vc4/vc4_kms.c
> +++ b/drivers/gpu/drm/vc4/vc4_kms.c
> @@ -389,8 +389,15 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
>   						500000000,
>   						new_hvs_state->core_clock_rate);
>   
> +		drm_dbg(dev, "Raising the core clock at %lu Hz\n", core_rate);
> +
> +		/*
> +		 * Do a temporary request on the core clock during the
> +		 * modeset.
> +		 */
>   		clk_set_min_rate(hvs->core_clk, core_rate);
>   	}
> +
>   	drm_atomic_helper_commit_modeset_disables(dev, state);
>   
>   	vc4_ctm_commit(vc4, state);
> @@ -416,6 +423,10 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
>   		drm_dbg(dev, "Running the core clock at %lu Hz\n",
>   			new_hvs_state->core_clock_rate);
>   
> +		/*
> +		 * Request a clock rate based on the current HVS
> +		 * requirements.
> +		 */
>   		clk_set_min_rate(hvs->core_clk, new_hvs_state->core_clock_rate);
>   	}
>   }

-- 
Thomas Zimmermann
Graphics Driver Developer
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
(HRB 36809, AG Nürnberg)
Geschäftsführer: Ivo Totev

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 840 bytes --]

Re: [PATCH v7 11/12] drm/vc4: Add logging and comments

[Thomas Zimmermann]

[-- Attachment #1.1: Type: text/plain, Size: 1650 bytes --]



Am 25.02.22 um 15:35 schrieb Maxime Ripard:
> The HVS core clock isn't really obvious, so let's add a bunch more
> comments and some logging for easier debugging.
> 
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>

> ---
>   drivers/gpu/drm/vc4/vc4_kms.c | 11 +++++++++++
>   1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
> index 24de29bc1cda..6fe03fc17d73 100644
> --- a/drivers/gpu/drm/vc4/vc4_kms.c
> +++ b/drivers/gpu/drm/vc4/vc4_kms.c
> @@ -389,8 +389,15 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
>   						500000000,
>   						new_hvs_state->core_clock_rate);
>   
> +		drm_dbg(dev, "Raising the core clock at %lu Hz\n", core_rate);
> +
> +		/*
> +		 * Do a temporary request on the core clock during the
> +		 * modeset.
> +		 */
>   		clk_set_min_rate(hvs->core_clk, core_rate);
>   	}
> +
>   	drm_atomic_helper_commit_modeset_disables(dev, state);
>   
>   	vc4_ctm_commit(vc4, state);
> @@ -416,6 +423,10 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
>   		drm_dbg(dev, "Running the core clock at %lu Hz\n",
>   			new_hvs_state->core_clock_rate);
>   
> +		/*
> +		 * Request a clock rate based on the current HVS
> +		 * requirements.
> +		 */
>   		clk_set_min_rate(hvs->core_clk, new_hvs_state->core_clock_rate);
>   	}
>   }

-- 
Thomas Zimmermann
Graphics Driver Developer
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
(HRB 36809, AG Nürnberg)
Geschäftsführer: Ivo Totev

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 840 bytes --]

Re: [PATCH v7 12/12] drm/vc4: hdmi: Remove clock rate initialization

[Thomas Zimmermann]

[-- Attachment #1.1: Type: text/plain, Size: 1560 bytes --]



Am 25.02.22 um 15:35 schrieb Maxime Ripard:
> Now that the clock driver makes sure we never end up with a rate of 0,
> the HDMI driver doesn't need to care anymore.
> 
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>

> ---
>   drivers/gpu/drm/vc4/vc4_hdmi.c | 13 -------------
>   1 file changed, 13 deletions(-)
> 
> diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
> index 92b1530aa17b..21aff3ad96cf 100644
> --- a/drivers/gpu/drm/vc4/vc4_hdmi.c
> +++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
> @@ -2576,19 +2576,6 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
>   			vc4_hdmi->disable_4kp60 = true;
>   	}
>   
> -	/*
> -	 * If we boot without any cable connected to the HDMI connector,
> -	 * the firmware will skip the HSM initialization and leave it
> -	 * with a rate of 0, resulting in a bus lockup when we're
> -	 * accessing the registers even if it's enabled.
> -	 *
> -	 * Let's put a sensible default at runtime_resume so that we
> -	 * don't end up in this situation.
> -	 */
> -	ret = clk_set_min_rate(vc4_hdmi->hsm_clock, HSM_MIN_CLOCK_FREQ);
> -	if (ret)
> -		goto err_put_ddc;
> -
>   	/*
>   	 * We need to have the device powered up at this point to call
>   	 * our reset hook and for the CEC init.

-- 
Thomas Zimmermann
Graphics Driver Developer
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
(HRB 36809, AG Nürnberg)
Geschäftsführer: Ivo Totev

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 840 bytes --]

Re: [PATCH v7 12/12] drm/vc4: hdmi: Remove clock rate initialization

[Thomas Zimmermann]

[-- Attachment #1.1: Type: text/plain, Size: 1560 bytes --]



Am 25.02.22 um 15:35 schrieb Maxime Ripard:
> Now that the clock driver makes sure we never end up with a rate of 0,
> the HDMI driver doesn't need to care anymore.
> 
> Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>

> ---
>   drivers/gpu/drm/vc4/vc4_hdmi.c | 13 -------------
>   1 file changed, 13 deletions(-)
> 
> diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
> index 92b1530aa17b..21aff3ad96cf 100644
> --- a/drivers/gpu/drm/vc4/vc4_hdmi.c
> +++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
> @@ -2576,19 +2576,6 @@ static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
>   			vc4_hdmi->disable_4kp60 = true;
>   	}
>   
> -	/*
> -	 * If we boot without any cable connected to the HDMI connector,
> -	 * the firmware will skip the HSM initialization and leave it
> -	 * with a rate of 0, resulting in a bus lockup when we're
> -	 * accessing the registers even if it's enabled.
> -	 *
> -	 * Let's put a sensible default at runtime_resume so that we
> -	 * don't end up in this situation.
> -	 */
> -	ret = clk_set_min_rate(vc4_hdmi->hsm_clock, HSM_MIN_CLOCK_FREQ);
> -	if (ret)
> -		goto err_put_ddc;
> -
>   	/*
>   	 * We need to have the device powered up at this point to call
>   	 * our reset hook and for the CEC init.

-- 
Thomas Zimmermann
Graphics Driver Developer
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
(HRB 36809, AG Nürnberg)
Geschäftsführer: Ivo Totev

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 840 bytes --]

Re: [PATCH v7 00/12] clk: Improve clock range handling

[Maxime Ripard]

On Fri, 25 Feb 2022 15:35:22 +0100, Maxime Ripard wrote:
> This is a follow-up of the discussion here:
> https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/
> 
> and here:
> https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/
> 
> While the initial proposal implemented a new API to temporarily raise and lower
> clock rates based on consumer workloads, Stephen suggested an
> alternative approach implemented here.
> 
> [...]

Applied to drm/drm-misc (drm-misc-next).

Thanks!
Maxime

Re: [PATCH v7 00/12] clk: Improve clock range handling

[Maxime Ripard]

On Fri, 25 Feb 2022 15:35:22 +0100, Maxime Ripard wrote:
> This is a follow-up of the discussion here:
> https://lore.kernel.org/linux-clk/20210319150355.xzw7ikwdaga2dwhv@gilmour/
> 
> and here:
> https://lore.kernel.org/all/20210914093515.260031-1-maxime@cerno.tech/
> 
> While the initial proposal implemented a new API to temporarily raise and lower
> clock rates based on consumer workloads, Stephen suggested an
> alternative approach implemented here.
> 
> [...]

Applied to drm/drm-misc (drm-misc-next).

Thanks!
Maxime