From: Marek Vasut <marex@denx.de>
To: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>,
"linux-usb@vger.kernel.org" <linux-usb@vger.kernel.org>
Cc: Amelie Delaunay <amelie.delaunay@st.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: Re: [PATCH] [RFC] usb: dwc2: Run the core connect in dwc2_hcd_init()
Date: Thu, 16 Apr 2020 11:46:35 +0200 [thread overview]
Message-ID: <6ea2270d-19a4-7e8b-42fb-37a4a9d81e1f@denx.de> (raw)
In-Reply-To: <4b4478aa-85bd-c05c-b5d0-e11dc35eb623@synopsys.com>
On 4/15/20 5:10 PM, Minas Harutyunyan wrote:
> Hi,
Hi,
> On 4/15/2020 6:55 PM, Marek Vasut wrote:
>> On 4/15/20 10:37 AM, Minas Harutyunyan wrote:
>>> Hi,
>>>
>>> On 4/14/2020 4:18 PM, Marek Vasut wrote:
>>>> On 4/14/20 9:14 AM, Minas Harutyunyan wrote:
>>>
>>>>
>>>>> 2. debug log
>>>>
>>>> What kind of debug log ?
>>>>
>>> Drivers debug log starting from dwc2 loading and connector connecting to
>>> device, where issue seen.
>>
>> How do I enable the one you need ?
>>
> To enable debug prints from dwc2 use 'make menuconfig':
>
> Symbol: USB_DWC2_DEBUG [=y]
Oh, this one, OK. There you go.
Note that there is no further output when I plug in the USB microB cable
from a PC.
dwc2 49000000.usb-otg: supply vusb_d not found, using dummy regulator
dwc2 49000000.usb-otg: supply vusb_a not found, using dummy regulator
dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
dwc2 49000000.usb-otg: bound driver zero
dwc2 49000000.usb-otg: DCFG=0x08100000, DCTL=0x00000002, DIEPMSK=00000000
dwc2 49000000.usb-otg: GAHBCFG=0x00000000, GHWCFG1=0x00000000
dwc2 49000000.usb-otg: GRXFSIZ=0x00000400, GNPTXFSIZ=0x04000400
dwc2 49000000.usb-otg: DPTx[1] FSize=1024, StAddr=0x00000800
dwc2 49000000.usb-otg: DPTx[2] FSize=1024, StAddr=0x00000c00
dwc2 49000000.usb-otg: DPTx[3] FSize=1024, StAddr=0x00001000
dwc2 49000000.usb-otg: DPTx[4] FSize=1024, StAddr=0x00001400
dwc2 49000000.usb-otg: DPTx[5] FSize=1024, StAddr=0x00001800
dwc2 49000000.usb-otg: DPTx[6] FSize=1024, StAddr=0x00001c00
dwc2 49000000.usb-otg: DPTx[7] FSize=1024, StAddr=0x00002000
dwc2 49000000.usb-otg: DPTx[8] FSize=1024, StAddr=0x00002400
dwc2 49000000.usb-otg: ep0-in: EPCTL=0x00008800, SIZ=0x00000000,
DMA=0x79daaf9c
dwc2 49000000.usb-otg: ep0-out: EPCTL=0x00008000, SIZ=0x00000000,
DMA=0xa167db6c
dwc2 49000000.usb-otg: ep1-in: EPCTL=0x00001000, SIZ=0x00000000,
DMA=0x88ad1397
dwc2 49000000.usb-otg: ep1-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0x6c5b357c
dwc2 49000000.usb-otg: ep2-in: EPCTL=0x00001800, SIZ=0x00000000,
DMA=0xb4639367
dwc2 49000000.usb-otg: ep2-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0x503148e2
dwc2 49000000.usb-otg: ep3-in: EPCTL=0x00002000, SIZ=0x00000000,
DMA=0x7e275f85
dwc2 49000000.usb-otg: ep3-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0x9474575a
dwc2 49000000.usb-otg: ep4-in: EPCTL=0x00002800, SIZ=0x00000000,
DMA=0xbe22b68d
dwc2 49000000.usb-otg: ep4-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0xb89ae0de
dwc2 49000000.usb-otg: ep5-in: EPCTL=0x00003000, SIZ=0x00000000,
DMA=0xa607065a
dwc2 49000000.usb-otg: ep5-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0xa8bc774f
dwc2 49000000.usb-otg: ep6-in: EPCTL=0x00003800, SIZ=0x00000000,
DMA=0xbabafaf5
dwc2 49000000.usb-otg: ep6-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0x58ddeb04
dwc2 49000000.usb-otg: ep7-in: EPCTL=0x00004000, SIZ=0x00000000,
DMA=0x8b6b00f3
dwc2 49000000.usb-otg: ep7-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0x87baf0d9
dwc2 49000000.usb-otg: ep8-in: EPCTL=0x00004800, SIZ=0x00000000,
DMA=0xa2c3caca
dwc2 49000000.usb-otg: ep8-out: EPCTL=0x00000000, SIZ=0x00000000,
DMA=0x67b6afe2
dwc2 49000000.usb-otg: DVBUSDIS=0x000017d7, DVBUSPULSE=000005b8
dwc2 49000000.usb-otg: DWC OTG Controller
dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 1
dwc2 49000000.usb-otg: irq 45, io mem 0x49000000
dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Device mode
next prev parent reply other threads:[~2020-04-16 10:19 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-04-13 14:31 [PATCH] [RFC] usb: dwc2: Run the core connect in dwc2_hcd_init() Marek Vasut
2020-04-13 14:45 ` Minas Harutyunyan
2020-04-13 14:54 ` Marek Vasut
2020-04-13 15:27 ` Minas Harutyunyan
2020-04-13 17:00 ` Marek Vasut
2020-04-14 7:14 ` Minas Harutyunyan
2020-04-14 12:18 ` Marek Vasut
2020-04-15 8:37 ` Minas Harutyunyan
2020-04-15 14:55 ` Marek Vasut
2020-04-15 15:10 ` Minas Harutyunyan
2020-04-16 9:46 ` Marek Vasut [this message]
2020-04-16 13:37 ` Minas Harutyunyan
2020-04-16 14:31 ` Marek Vasut
2020-04-17 9:00 ` Minas Harutyunyan
2020-04-20 12:09 ` Marek Vasut
2020-04-22 13:45 ` Minas Harutyunyan
2020-04-22 14:21 ` Marek Vasut
2020-05-14 0:10 ` Marek Vasut
2020-05-15 7:41 ` Minas Harutyunyan
2020-05-27 6:17 ` Minas Harutyunyan
2020-05-28 22:35 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6ea2270d-19a4-7e8b-42fb-37a4a9d81e1f@denx.de \
--to=marex@denx.de \
--cc=Minas.Harutyunyan@synopsys.com \
--cc=amelie.delaunay@st.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-usb@vger.kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.