[PATCH v4 04/16] dt_bindings: regulator: Add ROHM BD71815 PMIC regulators

[Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>]

Add binding documentation for regulators on ROHM BD71815 PMIC.
5 bucks, 7 LDOs and a boost for LED.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
No Changes since v3
 .../regulator/rohm,bd71815-regulator.yaml     | 116 ++++++++++++++++++
 1 file changed, 116 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml

diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml
new file mode 100644
index 000000000000..7d0adb74a396
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/rohm,bd71815-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71815 Power Management Integrated Circuit regulators
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  This module is part of the ROHM BD718215 MFD device. For more details
+  see Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml.
+
+  The regulator controller is represented as a sub-node of the PMIC node
+  on the device tree.
+
+  The valid names for BD71815 regulator nodes are
+  buck1, buck2, buck3, buck4, buck5,
+  ldo1, ldo2, ldo3, ldo4, ldo5,
+  ldodvref, ldolpsr, wled
+
+properties:
+  wled:
+    type: object
+    description:
+      properties for wled regulator
+    $ref: regulator.yaml#
+
+    properties:
+      regulator-name:
+        const: wled
+
+patternProperties:
+  "^((ldo|buck)[1-5]|ldolpsr|ldodvref)$":
+    type: object
+    description:
+      Properties for single LDO/BUCK regulator.
+    $ref: regulator.yaml#
+
+    properties:
+      regulator-name:
+        pattern: "^((ldo|buck)[1-5]|ldolpsr|ldodvref)$"
+        description:
+          should be "ldo1", ..., "ldo5", "buck1", ..., "buck5" and "ldolpsr"
+          for ldolpsr regulator, "ldodvref" for ldodvref reglator.
+
+      rohm,vsel-gpios:
+        description:
+          GPIO used to control ldo4 state (when ldo4 is controlled by GPIO).
+
+      rohm,dvs-run-voltage:
+        description:
+          PMIC "RUN" state voltage in uV when PMIC HW states are used. See
+          comments below for bucks/LDOs which support this. 0 means
+          regulator should be disabled at RUN state.
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-snvs-voltage:
+        description:
+          Whether to keep regulator enabled at "SNVS" state or not.
+          0 means regulator should be disabled at SNVS state, non zero voltage
+          keeps regulator enabled. BD71815 does not change voltage level
+          when PMIC transitions to SNVS.SNVS voltage depends on the previous
+          state (from which the PMIC transitioned to SNVS).
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-suspend-voltage:
+        description:
+          PMIC "SUSPEND" state voltage in uV when PMIC HW states are used. See
+          comments below for bucks/LDOs which support this. 0 means
+          regulator should be disabled at SUSPEND state.
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 3300000
+
+      rohm,dvs-lpsr-voltage:
+        description:
+          PMIC "LPSR" state voltage in uV when PMIC HW states are used. See
+          comments below for bucks/LDOs which support this. 0 means
+          regulator should be disabled at LPSR state.
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 3300000
+
+        # Bucks 1 and 2 support giving separate voltages for operational states
+        # (RUN /CLEAN according to data-sheet) and non operational states
+        # (LPSR/SUSPEND). The voltage is automatically changed when HW
+        # state changes. Omitting these properties from bucks 1 and 2 leave
+        # buck voltages to not be toggled by HW state. Enable status may still
+        # be toggled by state changes depending on HW default settings.
+        #
+        # Bucks 3-5 and ldos 1-5 support setting the RUN state voltage here.
+        # Given RUN voltage is used at all states if regulator is enabled at
+        # given state.
+        # Values given for other states are regarded as enable/disable at
+        # given state (see below).
+        #
+        # All regulators except WLED support specifying enable/disable status
+        # for each of the HW states (RUN/SNVS/SUSPEND/LPSR). HW defaults can
+        # be overridden by setting voltage to 0 (regulator disabled at given
+        # state) or non-zero (regulator enabled at given state). Please note
+        # that setting non zero voltages for bucks 1/2 will also enable voltage
+        # changes according to state change.
+
+    required:
+      - regulator-name
+
+    unevaluatedProperties: false
+
+additionalProperties: false
-- 
2.25.4


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]