From: Michal Simek <michal.simek@xilinx.com>
To: u-boot@lists.denx.de
Subject: [PATCH] spl: Kconfig: Use tabs instead of space for alignment
Date: Thu, 20 May 2021 13:08:44 +0200 [thread overview]
Message-ID: <73d735bdd118e8c6a7bdf6b77df0e96cb4e38979.1621508923.git.michal.simek@xilinx.com> (raw)
A lot of entries were using spaces instead of tab for alignment that's why
it is good to fix it to use the same style everywhere.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
common/spl/Kconfig | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index df5468f1ac29..b709a05a7b79 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -165,7 +165,7 @@ config SPL_BOARD_INIT
provided by the board.
config SPL_BOOTROM_SUPPORT
- bool "Support returning to the BOOTROM"
+ bool "Support returning to the BOOTROM"
help
Some platforms (e.g. the Rockchip RK3368) provide support in their
ROM for loading the next boot-stage after performing basic setup
@@ -707,7 +707,7 @@ config SYS_MMCSD_FS_BOOT_PARTITION
default 1
help
Partition on the MMC to load U-Boot from when the MMC is being
- used in fs mode
+ used in fs mode
config SPL_MMC_TINY
bool "Tiny MMC framework in SPL"
@@ -784,8 +784,8 @@ config SPL_NAND_SIMPLE
config SPL_NAND_BASE
depends on SPL_NAND_DRIVERS
bool "Use Base NAND Driver"
- help
- Include nand_base.c in the SPL.
+ help
+ Include nand_base.c in the SPL.
config SPL_NAND_IDENT
depends on SPL_NAND_BASE
@@ -1301,7 +1301,7 @@ config SPL_ATF_LOAD_IMAGE_V2
method, say Y.
config SPL_ATF_NO_PLATFORM_PARAM
- bool "Pass no platform parameter"
+ bool "Pass no platform parameter"
depends on SPL_ATF
help
While we expect to call a pointer to a valid FDT (or NULL)
@@ -1395,7 +1395,7 @@ config TPL_BOOTCOUNT_LIMIT
For example, it may be useful to choose the device to boot.
config TPL_LDSCRIPT
- string "Linker script for the TPL stage"
+ string "Linker script for the TPL stage"
depends on TPL
default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
default "arch/\$(ARCH)/cpu/u-boot-spl.lds"
@@ -1409,7 +1409,7 @@ config TPL_LDSCRIPT
fall back to the linker-script used for the SPL stage.
config TPL_NEEDS_SEPARATE_TEXT_BASE
- bool "TPL needs a separate text-base"
+ bool "TPL needs a separate text-base"
default n
depends on TPL
help
@@ -1418,7 +1418,7 @@ config TPL_NEEDS_SEPARATE_TEXT_BASE
.text sections of the TPL stage has to be set below.
config TPL_NEEDS_SEPARATE_STACK
- bool "TPL needs a separate initial stack-pointer"
+ bool "TPL needs a separate initial stack-pointer"
default n
depends on TPL
help
@@ -1426,20 +1426,20 @@ config TPL_NEEDS_SEPARATE_STACK
stack-pointer from the settings for the SPL stage.
config TPL_TEXT_BASE
- hex "Base address for the .text section of the TPL stage"
+ hex "Base address for the .text section of the TPL stage"
depends on TPL_NEEDS_SEPARATE_TEXT_BASE
help
The base address for the .text section of the TPL stage.
config TPL_MAX_SIZE
- int "Maximum size (in bytes) for the TPL stage"
+ int "Maximum size (in bytes) for the TPL stage"
default 0
depends on TPL
help
The maximum size (in bytes) of the TPL stage.
config TPL_STACK
- hex "Address of the initial stack-pointer for the TPL stage"
+ hex "Address of the initial stack-pointer for the TPL stage"
depends on TPL_NEEDS_SEPARATE_STACK
help
The address of the initial stack-pointer for the TPL stage.
@@ -1457,7 +1457,7 @@ config TPL_READ_ONLY
device-private data.
config TPL_BOOTROM_SUPPORT
- bool "Support returning to the BOOTROM (from TPL)"
+ bool "Support returning to the BOOTROM (from TPL)"
help
Some platforms (e.g. the Rockchip RK3368) provide support in their
ROM for loading the next boot-stage after performing basic setup
--
2.31.1
next reply other threads:[~2021-05-20 11:08 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-20 11:08 Michal Simek [this message]
2021-05-20 17:51 ` [PATCH] spl: Kconfig: Use tabs instead of space for alignment Simon Glass
2021-05-27 11:42 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=73d735bdd118e8c6a7bdf6b77df0e96cb4e38979.1621508923.git.michal.simek@xilinx.com \
--to=michal.simek@xilinx.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.