Re: [PATCH v3 03/14] remoteproc: Add new operation and flags for synchronistation

[Arnaud POULIQUEN <arnaud.pouliquen@st.com>]

On 4/24/20 10:01 PM, Mathieu Poirier wrote:
> Add a new sync_ops to support use cases where the remoteproc
> core is synchronising with the remote processor.  Exactly when to use
> the synchronisation operations is directed by the flags in structure
> rproc_sync_flags.
> 
> Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
> ---
>  include/linux/remoteproc.h | 24 ++++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
> 
> diff --git a/include/linux/remoteproc.h b/include/linux/remoteproc.h
> index ac4082f12e8b..ceb3b2bba824 100644
> --- a/include/linux/remoteproc.h
> +++ b/include/linux/remoteproc.h
> @@ -353,6 +353,23 @@ enum rsc_handling_status {
>  	RSC_IGNORED	= 1,
>  };
>  
> +/**
> + * struct rproc_sync_flags - platform specific flags indicating which
> + *			      rproc_ops to use at specific times during
> + *			      the rproc lifecycle.
> + * @on_init: true if synchronising with the remote processor at
> + *	     initialisation time
> + * @after_stop: true if synchronising with the remote processor after it was
> + *		stopped from the cmmand line
typo command
> + * @after_crash: true if synchronising with the remote processor after
> + *		 it has crashed
> + */
> +struct rproc_sync_flags {
> +	bool on_init;
> +	bool after_stop;
> +	bool after_crash;
> +};
> +
how about a bit field instead (just a proposition)?
Platform driver would set the sync flag and rproc_set_sync_flag could be a 
simple mask instead of a switch case.

Is it possible to split this patch in a different ways because difficult to understand as
rproc_sync_flags seems not used before 
[PATCH v3 09/14] remoteproc: Deal with synchronisation when crashing

Thanks
Arnaud  

>  /**
>   * struct rproc_ops - platform-specific device handlers
>   * @start:	power on the device and boot it
> @@ -459,6 +476,9 @@ struct rproc_dump_segment {
>   * @firmware: name of firmware file to be loaded
>   * @priv: private data which belongs to the platform-specific rproc module
>   * @ops: platform-specific start/stop rproc handlers
> + * @sync_ops: platform-specific start/stop rproc handlers when
> + *	      synchronising with a remote processor.
> + * @sync_flags: Determine the rproc_ops to choose in specific states.
>   * @dev: virtual device for refcounting and common remoteproc behavior
>   * @power: refcount of users who need this rproc powered up
>   * @state: state of the device
> @@ -482,6 +502,7 @@ struct rproc_dump_segment {
>   * @table_sz: size of @cached_table
>   * @has_iommu: flag to indicate if remote processor is behind an MMU
>   * @auto_boot: flag to indicate if remote processor should be auto-started
> + * @sync_with_rproc: true if currently synchronising with the rproc
>   * @dump_segments: list of segments in the firmware
>   * @nb_vdev: number of vdev currently handled by rproc
>   */
> @@ -492,6 +513,8 @@ struct rproc {
>  	const char *firmware;
>  	void *priv;
>  	struct rproc_ops *ops;
> +	struct rproc_ops *sync_ops;
> +	struct rproc_sync_flags sync_flags;
>  	struct device dev;
>  	atomic_t power;
>  	unsigned int state;
> @@ -515,6 +538,7 @@ struct rproc {
>  	size_t table_sz;
>  	bool has_iommu;
>  	bool auto_boot;
> +	bool sync_with_rproc;
>  	struct list_head dump_segments;
>  	int nb_vdev;
>  	u8 elf_class;
>