* [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 0:01 ` Vivek Unune
0 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 0:01 UTC (permalink / raw)
To: robh+dt, mark.rutland, heiko, ezequiel, jbx6244, akash
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel, Vivek Unune
- Add Hugsun X99 IR receiver and power led
- Remove pwm0 node as it interferes with pwer LED gpio
Also, it's not used in factory firmware
Tested with Libreelec kernel v5.6
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
---
.../boot/dts/rockchip/rk3399-hugsun-x99.dts | 37 +++++++++++++++++--
1 file changed, 33 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
index d69a613fb65a..df425e164a2e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
@@ -29,6 +29,26 @@
regulator-max-microvolt = <5000000>;
};
+ ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_rx>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_led_gpio>;
+
+ power-led {
+ label = "blue:power";
+ gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "none";
+ };
+ };
+
vcc_sys: vcc-sys {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
@@ -483,6 +503,18 @@
};
};
+ ir {
+ ir_rx: ir-rx {
+ rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ power_led_gpio: power-led-gpio {
+ rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
pmic {
pmic_int_l: pmic-int-l {
rockchip,pins =
@@ -539,10 +572,6 @@
};
};
-&pwm0 {
- status = "okay";
-};
-
&pwm2 {
status = "okay";
pinctrl-0 = <&pwm2_pin_pull_down>;
--
2.20.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 0:01 ` Vivek Unune
0 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 0:01 UTC (permalink / raw)
To: robh+dt, mark.rutland, heiko, ezequiel, jbx6244, akash
Cc: devicetree, Vivek Unune, linux-kernel, linux-arm-kernel, linux-rockchip
- Add Hugsun X99 IR receiver and power led
- Remove pwm0 node as it interferes with pwer LED gpio
Also, it's not used in factory firmware
Tested with Libreelec kernel v5.6
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
---
.../boot/dts/rockchip/rk3399-hugsun-x99.dts | 37 +++++++++++++++++--
1 file changed, 33 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
index d69a613fb65a..df425e164a2e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
@@ -29,6 +29,26 @@
regulator-max-microvolt = <5000000>;
};
+ ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_rx>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_led_gpio>;
+
+ power-led {
+ label = "blue:power";
+ gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "none";
+ };
+ };
+
vcc_sys: vcc-sys {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
@@ -483,6 +503,18 @@
};
};
+ ir {
+ ir_rx: ir-rx {
+ rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ power_led_gpio: power-led-gpio {
+ rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
pmic {
pmic_int_l: pmic-int-l {
rockchip,pins =
@@ -539,10 +572,6 @@
};
};
-&pwm0 {
- status = "okay";
-};
-
&pwm2 {
status = "okay";
pinctrl-0 = <&pwm2_pin_pull_down>;
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 8:32 ` Johan Jonker
0 siblings, 0 replies; 13+ messages in thread
From: Johan Jonker @ 2020-03-13 8:32 UTC (permalink / raw)
To: Vivek Unune, robh+dt, mark.rutland, heiko, ezequiel, akash
Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Hi Vivek,
The 'power-led' need some changes.
From leds-gpio.yaml:
patternProperties:
# The first form is preferred, but fall back to just 'led' anywhere in the
# node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
type: object
Test with:
make -k ARCH=arm64 dtbs_check
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
On 3/13/20 1:01 AM, Vivek Unune wrote:
> - Add Hugsun X99 IR receiver and power led
> - Remove pwm0 node as it interferes with pwer LED gpio
pwer => power
> Also, it's not used in factory firmware
>
> Tested with Libreelec kernel v5.6
Test with linux-next.
git clone -- depth 1
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
>
> Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
> ---
> .../boot/dts/rockchip/rk3399-hugsun-x99.dts | 37 +++++++++++++++++--
> 1 file changed, 33 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> index d69a613fb65a..df425e164a2e 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> @@ -29,6 +29,26 @@
> regulator-max-microvolt = <5000000>;
> };
>
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir_rx>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&power_led_gpio>;
> +
> + power-led {
> + label = "blue:power";
> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "none";
> + };
> + };
> +
> vcc_sys: vcc-sys {
> compatible = "regulator-fixed";
> regulator-name = "vcc_sys";
> @@ -483,6 +503,18 @@
> };
> };
>
> + ir {
> + ir_rx: ir-rx {
> + rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + power_led_gpio: power-led-gpio {
> + rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> pmic {
> pmic_int_l: pmic-int-l {
> rockchip,pins =
> @@ -539,10 +572,6 @@
> };
> };
>
> -&pwm0 {
> - status = "okay";
> -};
> -
> &pwm2 {
> status = "okay";
> pinctrl-0 = <&pwm2_pin_pull_down>;
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 8:32 ` Johan Jonker
0 siblings, 0 replies; 13+ messages in thread
From: Johan Jonker @ 2020-03-13 8:32 UTC (permalink / raw)
To: Vivek Unune, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, heiko-4mtYJXux2i+zQB+pC5nmwQ,
ezequiel-ZGY8ohtN/8qB+jHODAdFcQ, akash-oRp2ZoJdM/RWk0Htik3J/w
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Hi Vivek,
The 'power-led' need some changes.
From leds-gpio.yaml:
patternProperties:
# The first form is preferred, but fall back to just 'led' anywhere in the
# node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
type: object
Test with:
make -k ARCH=arm64 dtbs_check
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
On 3/13/20 1:01 AM, Vivek Unune wrote:
> - Add Hugsun X99 IR receiver and power led
> - Remove pwm0 node as it interferes with pwer LED gpio
pwer => power
> Also, it's not used in factory firmware
>
> Tested with Libreelec kernel v5.6
Test with linux-next.
git clone -- depth 1
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
>
> Signed-off-by: Vivek Unune <npcomplete13-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> .../boot/dts/rockchip/rk3399-hugsun-x99.dts | 37 +++++++++++++++++--
> 1 file changed, 33 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> index d69a613fb65a..df425e164a2e 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> @@ -29,6 +29,26 @@
> regulator-max-microvolt = <5000000>;
> };
>
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir_rx>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&power_led_gpio>;
> +
> + power-led {
> + label = "blue:power";
> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "none";
> + };
> + };
> +
> vcc_sys: vcc-sys {
> compatible = "regulator-fixed";
> regulator-name = "vcc_sys";
> @@ -483,6 +503,18 @@
> };
> };
>
> + ir {
> + ir_rx: ir-rx {
> + rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + power_led_gpio: power-led-gpio {
> + rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> pmic {
> pmic_int_l: pmic-int-l {
> rockchip,pins =
> @@ -539,10 +572,6 @@
> };
> };
>
> -&pwm0 {
> - status = "okay";
> -};
> -
> &pwm2 {
> status = "okay";
> pinctrl-0 = <&pwm2_pin_pull_down>;
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 8:32 ` Johan Jonker
0 siblings, 0 replies; 13+ messages in thread
From: Johan Jonker @ 2020-03-13 8:32 UTC (permalink / raw)
To: Vivek Unune, robh+dt, mark.rutland, heiko, ezequiel, akash
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-rockchip
Hi Vivek,
The 'power-led' need some changes.
From leds-gpio.yaml:
patternProperties:
# The first form is preferred, but fall back to just 'led' anywhere in the
# node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
type: object
Test with:
make -k ARCH=arm64 dtbs_check
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
On 3/13/20 1:01 AM, Vivek Unune wrote:
> - Add Hugsun X99 IR receiver and power led
> - Remove pwm0 node as it interferes with pwer LED gpio
pwer => power
> Also, it's not used in factory firmware
>
> Tested with Libreelec kernel v5.6
Test with linux-next.
git clone -- depth 1
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
>
> Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
> ---
> .../boot/dts/rockchip/rk3399-hugsun-x99.dts | 37 +++++++++++++++++--
> 1 file changed, 33 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> index d69a613fb65a..df425e164a2e 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> @@ -29,6 +29,26 @@
> regulator-max-microvolt = <5000000>;
> };
>
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir_rx>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&power_led_gpio>;
> +
> + power-led {
> + label = "blue:power";
> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + linux,default-trigger = "none";
> + };
> + };
> +
> vcc_sys: vcc-sys {
> compatible = "regulator-fixed";
> regulator-name = "vcc_sys";
> @@ -483,6 +503,18 @@
> };
> };
>
> + ir {
> + ir_rx: ir-rx {
> + rockchip,pins = <0 RK_PA6 1 &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + power_led_gpio: power-led-gpio {
> + rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> pmic {
> pmic_int_l: pmic-int-l {
> rockchip,pins =
> @@ -539,10 +572,6 @@
> };
> };
>
> -&pwm0 {
> - status = "okay";
> -};
> -
> &pwm2 {
> status = "okay";
> pinctrl-0 = <&pwm2_pin_pull_down>;
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 14:20 ` Vivek Unune
0 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 14:20 UTC (permalink / raw)
To: Johan Jonker
Cc: robh+dt, mark.rutland, heiko, ezequiel, akash, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
> Hi Vivek,
>
> The 'power-led' need some changes.
>
> From leds-gpio.yaml:
>
> patternProperties:
> # The first form is preferred, but fall back to just 'led' anywhere in the
> # node name to at least catch some child nodes.
> "(^led-[0-9a-f]$|led)":
> type: object
>
> Test with:
> make -k ARCH=arm64 dtbs_check
>
> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
>
> On 3/13/20 1:01 AM, Vivek Unune wrote:
> > - Add Hugsun X99 IR receiver and power led
> > - Remove pwm0 node as it interferes with pwer LED gpio
>
> pwer => power
>
Hi Johan,
I'll fix those in my next version. Here's what I intended to to:
1. Rename 'power-led' node to 'led-power'
2. Remove 'linux,default-trigger' entirely since this led is always on
Thanks,
Vivek
> > index d69a613fb65a..df425e164a2e 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> > @@ -29,6 +29,26 @@
> > regulator-max-microvolt = <5000000>;
> > };
> >
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&power_led_gpio>;
> > +
> > + power-led {
> > + label = "blue:power";
> > + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> > + default-state = "on";
> > + linux,default-trigger = "none";
> > + };
> > + };
> > +
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 14:20 ` Vivek Unune
0 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 14:20 UTC (permalink / raw)
To: Johan Jonker
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
heiko-4mtYJXux2i+zQB+pC5nmwQ, ezequiel-ZGY8ohtN/8qB+jHODAdFcQ,
akash-oRp2ZoJdM/RWk0Htik3J/w, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
> Hi Vivek,
>
> The 'power-led' need some changes.
>
> From leds-gpio.yaml:
>
> patternProperties:
> # The first form is preferred, but fall back to just 'led' anywhere in the
> # node name to at least catch some child nodes.
> "(^led-[0-9a-f]$|led)":
> type: object
>
> Test with:
> make -k ARCH=arm64 dtbs_check
>
> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
>
> On 3/13/20 1:01 AM, Vivek Unune wrote:
> > - Add Hugsun X99 IR receiver and power led
> > - Remove pwm0 node as it interferes with pwer LED gpio
>
> pwer => power
>
Hi Johan,
I'll fix those in my next version. Here's what I intended to to:
1. Rename 'power-led' node to 'led-power'
2. Remove 'linux,default-trigger' entirely since this led is always on
Thanks,
Vivek
> > index d69a613fb65a..df425e164a2e 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> > @@ -29,6 +29,26 @@
> > regulator-max-microvolt = <5000000>;
> > };
> >
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&power_led_gpio>;
> > +
> > + power-led {
> > + label = "blue:power";
> > + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> > + default-state = "on";
> > + linux,default-trigger = "none";
> > + };
> > + };
> > +
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 14:20 ` Vivek Unune
0 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 14:20 UTC (permalink / raw)
To: Johan Jonker
Cc: mark.rutland, devicetree, heiko, linux-kernel, linux-rockchip,
robh+dt, akash, ezequiel, linux-arm-kernel
On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
> Hi Vivek,
>
> The 'power-led' need some changes.
>
> From leds-gpio.yaml:
>
> patternProperties:
> # The first form is preferred, but fall back to just 'led' anywhere in the
> # node name to at least catch some child nodes.
> "(^led-[0-9a-f]$|led)":
> type: object
>
> Test with:
> make -k ARCH=arm64 dtbs_check
>
> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
>
> On 3/13/20 1:01 AM, Vivek Unune wrote:
> > - Add Hugsun X99 IR receiver and power led
> > - Remove pwm0 node as it interferes with pwer LED gpio
>
> pwer => power
>
Hi Johan,
I'll fix those in my next version. Here's what I intended to to:
1. Rename 'power-led' node to 'led-power'
2. Remove 'linux,default-trigger' entirely since this led is always on
Thanks,
Vivek
> > index d69a613fb65a..df425e164a2e 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> > +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
> > @@ -29,6 +29,26 @@
> > regulator-max-microvolt = <5000000>;
> > };
> >
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&power_led_gpio>;
> > +
> > + power-led {
> > + label = "blue:power";
> > + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> > + default-state = "on";
> > + linux,default-trigger = "none";
> > + };
> > + };
> > +
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
2020-03-13 14:20 ` Vivek Unune
(?)
@ 2020-03-13 14:29 ` Johan Jonker
-1 siblings, 0 replies; 13+ messages in thread
From: Johan Jonker @ 2020-03-13 14:29 UTC (permalink / raw)
To: Vivek Unune
Cc: robh+dt, mark.rutland, heiko, ezequiel, akash, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
Hi Vivek,
On 3/13/20 3:20 PM, Vivek Unune wrote:
> On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
>> Hi Vivek,
>>
>> The 'power-led' need some changes.
>>
>> From leds-gpio.yaml:
>>
>> patternProperties:
>> # The first form is preferred, but fall back to just 'led' anywhere in the
>> # node name to at least catch some child nodes.
>> "(^led-[0-9a-f]$|led)":
>> type: object
>>
>> Test with:
>> make -k ARCH=arm64 dtbs_check
>>
>> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
>> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
>> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
>>
>> On 3/13/20 1:01 AM, Vivek Unune wrote:
>>> - Add Hugsun X99 IR receiver and power led
>>> - Remove pwm0 node as it interferes with pwer LED gpio
>>
>> pwer => power
>>
>
> Hi Johan,
>
> I'll fix those in my next version. Here's what I intended to to:
>
> 1. Rename 'power-led' node to 'led-power'
The first form is preferred.
Put 'led-power' in a regex tester with ^led-[0-9a-f]$
https://regex101.com/
Your regular expression does not match the subject string.
Test 'led-0'
Full match
> 2. Remove 'linux,default-trigger' entirely since this led is always on
>
> Thanks,
>
> Vivek
>
>>> index d69a613fb65a..df425e164a2e 100644
>>> --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
>>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
>>> @@ -29,6 +29,26 @@
>>> regulator-max-microvolt = <5000000>;
>>> };
>>>
>>> + leds {
>>> + compatible = "gpio-leds";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&power_led_gpio>;
>>> +
>>> + power-led {
>>> + label = "blue:power";
>>> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
>>> + default-state = "on";
>>> + linux,default-trigger = "none";
>>> + };
>>> + };
>>> +
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 14:29 ` Johan Jonker
0 siblings, 0 replies; 13+ messages in thread
From: Johan Jonker @ 2020-03-13 14:29 UTC (permalink / raw)
To: Vivek Unune
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
heiko-4mtYJXux2i+zQB+pC5nmwQ, ezequiel-ZGY8ohtN/8qB+jHODAdFcQ,
akash-oRp2ZoJdM/RWk0Htik3J/w, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Hi Vivek,
On 3/13/20 3:20 PM, Vivek Unune wrote:
> On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
>> Hi Vivek,
>>
>> The 'power-led' need some changes.
>>
>> From leds-gpio.yaml:
>>
>> patternProperties:
>> # The first form is preferred, but fall back to just 'led' anywhere in the
>> # node name to at least catch some child nodes.
>> "(^led-[0-9a-f]$|led)":
>> type: object
>>
>> Test with:
>> make -k ARCH=arm64 dtbs_check
>>
>> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
>> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
>> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
>>
>> On 3/13/20 1:01 AM, Vivek Unune wrote:
>>> - Add Hugsun X99 IR receiver and power led
>>> - Remove pwm0 node as it interferes with pwer LED gpio
>>
>> pwer => power
>>
>
> Hi Johan,
>
> I'll fix those in my next version. Here's what I intended to to:
>
> 1. Rename 'power-led' node to 'led-power'
The first form is preferred.
Put 'led-power' in a regex tester with ^led-[0-9a-f]$
https://regex101.com/
Your regular expression does not match the subject string.
Test 'led-0'
Full match
> 2. Remove 'linux,default-trigger' entirely since this led is always on
>
> Thanks,
>
> Vivek
>
>>> index d69a613fb65a..df425e164a2e 100644
>>> --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
>>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
>>> @@ -29,6 +29,26 @@
>>> regulator-max-microvolt = <5000000>;
>>> };
>>>
>>> + leds {
>>> + compatible = "gpio-leds";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&power_led_gpio>;
>>> +
>>> + power-led {
>>> + label = "blue:power";
>>> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
>>> + default-state = "on";
>>> + linux,default-trigger = "none";
>>> + };
>>> + };
>>> +
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 14:29 ` Johan Jonker
0 siblings, 0 replies; 13+ messages in thread
From: Johan Jonker @ 2020-03-13 14:29 UTC (permalink / raw)
To: Vivek Unune
Cc: mark.rutland, devicetree, heiko, linux-kernel, linux-rockchip,
robh+dt, akash, ezequiel, linux-arm-kernel
Hi Vivek,
On 3/13/20 3:20 PM, Vivek Unune wrote:
> On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
>> Hi Vivek,
>>
>> The 'power-led' need some changes.
>>
>> From leds-gpio.yaml:
>>
>> patternProperties:
>> # The first form is preferred, but fall back to just 'led' anywhere in the
>> # node name to at least catch some child nodes.
>> "(^led-[0-9a-f]$|led)":
>> type: object
>>
>> Test with:
>> make -k ARCH=arm64 dtbs_check
>>
>> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
>> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
>> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
>>
>> On 3/13/20 1:01 AM, Vivek Unune wrote:
>>> - Add Hugsun X99 IR receiver and power led
>>> - Remove pwm0 node as it interferes with pwer LED gpio
>>
>> pwer => power
>>
>
> Hi Johan,
>
> I'll fix those in my next version. Here's what I intended to to:
>
> 1. Rename 'power-led' node to 'led-power'
The first form is preferred.
Put 'led-power' in a regex tester with ^led-[0-9a-f]$
https://regex101.com/
Your regular expression does not match the subject string.
Test 'led-0'
Full match
> 2. Remove 'linux,default-trigger' entirely since this led is always on
>
> Thanks,
>
> Vivek
>
>>> index d69a613fb65a..df425e164a2e 100644
>>> --- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
>>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
>>> @@ -29,6 +29,26 @@
>>> regulator-max-microvolt = <5000000>;
>>> };
>>>
>>> + leds {
>>> + compatible = "gpio-leds";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&power_led_gpio>;
>>> +
>>> + power-led {
>>> + label = "blue:power";
>>> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
>>> + default-state = "on";
>>> + linux,default-trigger = "none";
>>> + };
>>> + };
>>> +
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
2020-03-13 14:29 ` Johan Jonker
@ 2020-03-13 14:37 ` Vivek Unune
-1 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 14:37 UTC (permalink / raw)
To: Johan Jonker
Cc: robh+dt, mark.rutland, heiko, ezequiel, akash, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
On Fri, Mar 13, 2020 at 03:29:59PM +0100, Johan Jonker wrote:
> Hi Vivek,
>
> On 3/13/20 3:20 PM, Vivek Unune wrote:
> > On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
> >> Hi Vivek,
> >>
> >> The 'power-led' need some changes.
> >>
> >> From leds-gpio.yaml:
> >>
> >> patternProperties:
> >> # The first form is preferred, but fall back to just 'led' anywhere in the
> >> # node name to at least catch some child nodes.
> >> "(^led-[0-9a-f]$|led)":
> >> type: object
> >>
> >> Test with:
> >> make -k ARCH=arm64 dtbs_check
> >>
> >> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
> >> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
> >> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
> >>
> >> On 3/13/20 1:01 AM, Vivek Unune wrote:
> >>> - Add Hugsun X99 IR receiver and power led
> >>> - Remove pwm0 node as it interferes with pwer LED gpio
> >>
> >> pwer => power
> >>
> >
> > Hi Johan,
> >
> > I'll fix those in my next version. Here's what I intended to to:
> >
>
> > 1. Rename 'power-led' node to 'led-power'
>
> The first form is preferred.
> Put 'led-power' in a regex tester with ^led-[0-9a-f]$
> https://regex101.com/
> Your regular expression does not match the subject string.
>
> Test 'led-0'
> Full match
>
Hi Johan,
Thanks for quick reply.
Indeed led-power won't work. Although I'm trying to figure out the dtbs_check
Currently, make compains that it's missing.
I'll verify this properly without having you to verify it next time.
Thanks,
Vivek
> >>> regulator-max-microvolt = <5000000>;
> >>> };
> >>>
> >>> + leds {
> >>> + compatible = "gpio-leds";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&power_led_gpio>;
> >>> +
> >>> + power-led {
> >>> + label = "blue:power";
> >>> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> >>> + default-state = "on";
> >>> + linux,default-trigger = "none";
> >>> + };
> >>> + };
> >>> +
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led
@ 2020-03-13 14:37 ` Vivek Unune
0 siblings, 0 replies; 13+ messages in thread
From: Vivek Unune @ 2020-03-13 14:37 UTC (permalink / raw)
To: Johan Jonker
Cc: mark.rutland, devicetree, heiko, linux-kernel, linux-rockchip,
robh+dt, akash, ezequiel, linux-arm-kernel
On Fri, Mar 13, 2020 at 03:29:59PM +0100, Johan Jonker wrote:
> Hi Vivek,
>
> On 3/13/20 3:20 PM, Vivek Unune wrote:
> > On Fri, Mar 13, 2020 at 09:32:27AM +0100, Johan Jonker wrote:
> >> Hi Vivek,
> >>
> >> The 'power-led' need some changes.
> >>
> >> From leds-gpio.yaml:
> >>
> >> patternProperties:
> >> # The first form is preferred, but fall back to just 'led' anywhere in the
> >> # node name to at least catch some child nodes.
> >> "(^led-[0-9a-f]$|led)":
> >> type: object
> >>
> >> Test with:
> >> make -k ARCH=arm64 dtbs_check
> >>
> >> arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: leds:
> >> power-led:linux,default-trigger:0: 'none' is not one of ['backlight',
> >> 'default-on', 'heartbeat', 'disk-activity', 'ide-disk', 'timer', 'pattern']
> >>
> >> On 3/13/20 1:01 AM, Vivek Unune wrote:
> >>> - Add Hugsun X99 IR receiver and power led
> >>> - Remove pwm0 node as it interferes with pwer LED gpio
> >>
> >> pwer => power
> >>
> >
> > Hi Johan,
> >
> > I'll fix those in my next version. Here's what I intended to to:
> >
>
> > 1. Rename 'power-led' node to 'led-power'
>
> The first form is preferred.
> Put 'led-power' in a regex tester with ^led-[0-9a-f]$
> https://regex101.com/
> Your regular expression does not match the subject string.
>
> Test 'led-0'
> Full match
>
Hi Johan,
Thanks for quick reply.
Indeed led-power won't work. Although I'm trying to figure out the dtbs_check
Currently, make compains that it's missing.
I'll verify this properly without having you to verify it next time.
Thanks,
Vivek
> >>> regulator-max-microvolt = <5000000>;
> >>> };
> >>>
> >>> + leds {
> >>> + compatible = "gpio-leds";
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&power_led_gpio>;
> >>> +
> >>> + power-led {
> >>> + label = "blue:power";
> >>> + gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
> >>> + default-state = "on";
> >>> + linux,default-trigger = "none";
> >>> + };
> >>> + };
> >>> +
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2020-03-13 14:37 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-13 0:01 [PATCH] arm64: dts: rockchip: Add Hugsun X99 IR receiver and power led Vivek Unune
2020-03-13 0:01 ` Vivek Unune
2020-03-13 8:32 ` Johan Jonker
2020-03-13 8:32 ` Johan Jonker
2020-03-13 8:32 ` Johan Jonker
2020-03-13 14:20 ` Vivek Unune
2020-03-13 14:20 ` Vivek Unune
2020-03-13 14:20 ` Vivek Unune
2020-03-13 14:29 ` Johan Jonker
2020-03-13 14:29 ` Johan Jonker
2020-03-13 14:29 ` Johan Jonker
2020-03-13 14:37 ` Vivek Unune
2020-03-13 14:37 ` Vivek Unune
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.