* [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-07-24 6:52 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 6:52 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, icenowy, megous, clabbe, bage, devicetree
Cc: linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm, Frank Lee
This patch set adds initial support for allwinner a100 soc,
which is a 64-bit tablet chip.
v5:
-Drop redundant SOB for thermal series patch
-Trival a100 dtsi fix
v4:
-Drop "dt-bindings: pinctrl: sunxi: make gpio banks supplies required"
-Fix dcdc1 regulator name
-Get rid of underscore in dts node name
-Some trivial things in yaml files
v3:
-Add pmu and nmi support
-Add read data mask for calibration
-Code style
-Some trivial things in yaml files
v2:
-Some naming consistency
-Repair email address
-Fix mmc clock
-Don't export system clock
-Fix checkpatch warning
-Drop unneeded pin function, convert to jtag_gpu and i2s_x
Yangtao Li (16):
dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and
R-CCU
clk: sunxi-ng: add support for the Allwinner A100 CCU
dt-bindings: pinctrl: sunxi: Get rid of continual nesting
dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
pinctrl: sunxi: add support for the Allwinner A100 pin controller
dt-bindings: nvmem: SID: add binding for A100's SID controller
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in
sun50i_h6_ths_calibrate
thermal: sun8i: Add A100's THS controller support
mfd: axp20x: Allow the AXP803 to be probed by I2C
dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
arm64: allwinner: A100: add support for Allwinner Perf1 board
.../devicetree/bindings/arm/sunxi.yaml | 5 +
.../clock/allwinner,sun4i-a10-ccu.yaml | 7 +-
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 3 +
.../allwinner,sun7i-a20-sc-nmi.yaml | 5 +-
.../nvmem/allwinner,sun4i-a10-sid.yaml | 19 +-
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 139 +-
.../thermal/allwinner,sun8i-a83t-ths.yaml | 6 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-a100-allwinner-perf1.dts | 180 +++
.../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 364 +++++
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
drivers/mfd/axp20x-i2c.c | 2 +
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 ++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 +++++++++
drivers/thermal/sun8i_thermal.c | 16 +-
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
26 files changed, 3308 insertions(+), 68 deletions(-)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
--
2.24.0
^ permalink raw reply [flat|nested] 84+ messages in thread
* [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-07-24 6:52 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 6:52 UTC (permalink / raw)
To: robh+dt, mripard, wens, mturquette, sboyd, gregory.clement, tglx,
jason, maz, srinivas.kandagatla, linus.walleij, anarsoul,
tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria, lee.jones,
p.zabel, icenowy, megous, clabbe, bage, devicetree
Cc: linux-pm, linux-kernel, linux-gpio, linux-i2c, Frank Lee,
linux-clk, linux-arm-kernel
This patch set adds initial support for allwinner a100 soc,
which is a 64-bit tablet chip.
v5:
-Drop redundant SOB for thermal series patch
-Trival a100 dtsi fix
v4:
-Drop "dt-bindings: pinctrl: sunxi: make gpio banks supplies required"
-Fix dcdc1 regulator name
-Get rid of underscore in dts node name
-Some trivial things in yaml files
v3:
-Add pmu and nmi support
-Add read data mask for calibration
-Code style
-Some trivial things in yaml files
v2:
-Some naming consistency
-Repair email address
-Fix mmc clock
-Don't export system clock
-Fix checkpatch warning
-Drop unneeded pin function, convert to jtag_gpu and i2s_x
Yangtao Li (16):
dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and
R-CCU
clk: sunxi-ng: add support for the Allwinner A100 CCU
dt-bindings: pinctrl: sunxi: Get rid of continual nesting
dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
pinctrl: sunxi: add support for the Allwinner A100 pin controller
dt-bindings: nvmem: SID: add binding for A100's SID controller
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in
sun50i_h6_ths_calibrate
thermal: sun8i: Add A100's THS controller support
mfd: axp20x: Allow the AXP803 to be probed by I2C
dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
arm64: allwinner: A100: add support for Allwinner Perf1 board
.../devicetree/bindings/arm/sunxi.yaml | 5 +
.../clock/allwinner,sun4i-a10-ccu.yaml | 7 +-
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 3 +
.../allwinner,sun7i-a20-sc-nmi.yaml | 5 +-
.../nvmem/allwinner,sun4i-a10-sid.yaml | 19 +-
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 139 +-
.../thermal/allwinner,sun8i-a83t-ths.yaml | 6 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-a100-allwinner-perf1.dts | 180 +++
.../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 364 +++++
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
drivers/mfd/axp20x-i2c.c | 2 +
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 ++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 +++++++++
drivers/thermal/sun8i_thermal.c | 16 +-
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
26 files changed, 3308 insertions(+), 68 deletions(-)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* [PATCH v5 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 6:56 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 6:56 UTC (permalink / raw)
To: mturquette, sboyd, robh+dt, mripard, wens
Cc: linux-clk, devicetree, linux-arm-kernel, linux-kernel,
Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
This patch adds binding to a100's ccu clock and r-ccu clock.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 4d382128b711..3b45344ed758 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -36,6 +36,8 @@ properties:
- allwinner,sun9i-a80-ccu
- allwinner,sun50i-a64-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h5-ccu
- allwinner,sun50i-h6-ccu
- allwinner,sun50i-h6-r-ccu
@@ -78,6 +80,7 @@ if:
- allwinner,sun8i-a83t-r-ccu
- allwinner,sun8i-h3-r-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h6-r-ccu
then:
@@ -94,7 +97,9 @@ else:
if:
properties:
compatible:
- const: allwinner,sun50i-h6-ccu
+ enum:
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-h6-ccu
then:
properties:
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
@ 2020-07-24 6:56 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 6:56 UTC (permalink / raw)
To: mturquette, sboyd, robh+dt, mripard, wens
Cc: Rob Herring, devicetree, linux-kernel, Yangtao Li, linux-clk,
linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
This patch adds binding to a100's ccu clock and r-ccu clock.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 4d382128b711..3b45344ed758 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -36,6 +36,8 @@ properties:
- allwinner,sun9i-a80-ccu
- allwinner,sun50i-a64-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h5-ccu
- allwinner,sun50i-h6-ccu
- allwinner,sun50i-h6-r-ccu
@@ -78,6 +80,7 @@ if:
- allwinner,sun8i-a83t-r-ccu
- allwinner,sun8i-h3-r-ccu
- allwinner,sun50i-a64-r-ccu
+ - allwinner,sun50i-a100-r-ccu
- allwinner,sun50i-h6-r-ccu
then:
@@ -94,7 +97,9 @@ else:
if:
properties:
compatible:
- const: allwinner,sun50i-h6-ccu
+ enum:
+ - allwinner,sun50i-a100-ccu
+ - allwinner,sun50i-h6-ccu
then:
properties:
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 6:58 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 6:58 UTC (permalink / raw)
To: mturquette, sboyd, mripard, wens, robh+dt, p.zabel, linux-kernel,
linux-clk, linux-arm-kernel, devicetree
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
Add support for a100 in the sunxi-ng CCU framework.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
10 files changed, 1804 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index cdf333003c30..ce5f5847d5d3 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -17,6 +17,16 @@ config SUN50I_A64_CCU
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+config SUN50I_A100_CCU
+ bool "Support for the Allwinner A100 CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
+config SUN50I_A100_R_CCU
+ bool "Support for the Allwinner A100 PRCM CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
config SUN50I_H6_CCU
bool "Support for the Allwinner H6 CCU"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 4c7bee883f2f..3eb5cff40eac 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,6 +23,8 @@ obj-y += ccu_mp.o
# SoC support
obj-$(CONFIG_SUNIV_F1C100S_CCU) += ccu-suniv-f1c100s.o
obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
+obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o
+obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o
obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o
obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o
obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
new file mode 100644
index 000000000000..a56142b90993
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100-r.h"
+
+static const char * const cpus_r_apb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0" };
+static const struct ccu_mux_var_prediv cpus_r_apb2_predivs[] = {
+ { .index = 3, .shift = 0, .width = 5 },
+};
+
+static struct ccu_div r_cpus_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x000,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("cpus",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static CLK_FIXED_FACTOR_HW(r_ahb_clk, "r-ahb", &r_cpus_clk.common.hw, 1, 1, 0);
+
+static struct ccu_div r_apb1_clk = {
+ .div = _SUNXI_CCU_DIV(0, 2),
+
+ .common = {
+ .reg = 0x00c,
+ .hw.init = CLK_HW_INIT("r-apb1",
+ "r-ahb",
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct ccu_div r_apb2_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x010,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("r-apb2",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static const struct clk_parent_data clk_parent_r_apb1[] = {
+ { .hw = &r_apb1_clk.common.hw },
+};
+
+static const struct clk_parent_data clk_parent_r_apb2[] = {
+ { .hw = &r_apb2_clk.common.hw },
+};
+
+static SUNXI_CCU_GATE_DATA(r_apb1_timer_clk, "r-apb1-timer", clk_parent_r_apb1,
+ 0x11c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_twd_clk, "r-apb1-twd", clk_parent_r_apb1,
+ 0x12c, BIT(0), 0);
+
+static const char * const r_apb1_pwm_clk_parents[] = { "dcxo24M", "osc32k",
+ "iosc" };
+static SUNXI_CCU_MUX(r_apb1_pwm_clk, "r-apb1-pwm", r_apb1_pwm_clk_parents,
+ 0x130, 24, 2, 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_pwm_clk, "r-apb1-bus-pwm",
+ clk_parent_r_apb1, 0x13c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_ppu_clk, "r-apb1-ppu", clk_parent_r_apb1,
+ 0x17c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_uart_clk, "r-apb2-uart", clk_parent_r_apb2,
+ 0x18c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c0_clk, "r-apb2-i2c0", clk_parent_r_apb2,
+ 0x19c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c1_clk, "r-apb2-i2c1", clk_parent_r_apb2,
+ 0x19c, BIT(1), 0);
+
+static const char * const r_apb1_ir_rx_parents[] = { "osc32k", "dcxo24M" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(r_apb1_ir_rx_clk, "r-apb1-ir-rx",
+ r_apb1_ir_rx_parents, 0x1c0,
+ 0, 5, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_ir_rx_clk, "r-apb1-bus-ir-rx",
+ clk_parent_r_apb1, 0x1cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(r_ahb_bus_rtc_clk, "r-ahb-rtc", "r-ahb",
+ 0x20c, BIT(0), 0);
+
+static struct ccu_common *sun50i_a100_r_ccu_clks[] = {
+ &r_cpus_clk.common,
+ &r_apb1_clk.common,
+ &r_apb2_clk.common,
+ &r_apb1_timer_clk.common,
+ &r_apb1_twd_clk.common,
+ &r_apb1_pwm_clk.common,
+ &r_apb1_bus_pwm_clk.common,
+ &r_apb1_ppu_clk.common,
+ &r_apb2_uart_clk.common,
+ &r_apb2_i2c0_clk.common,
+ &r_apb2_i2c1_clk.common,
+ &r_apb1_ir_rx_clk.common,
+ &r_apb1_bus_ir_rx_clk.common,
+ &r_ahb_bus_rtc_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_r_hw_clks = {
+ .hws = {
+ [CLK_R_CPUS] = &r_cpus_clk.common.hw,
+ [CLK_R_AHB] = &r_ahb_clk.hw,
+ [CLK_R_APB1] = &r_apb1_clk.common.hw,
+ [CLK_R_APB2] = &r_apb2_clk.common.hw,
+ [CLK_R_APB1_TIMER] = &r_apb1_timer_clk.common.hw,
+ [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw,
+ [CLK_R_APB1_PWM] = &r_apb1_pwm_clk.common.hw,
+ [CLK_R_APB1_BUS_PWM] = &r_apb1_bus_pwm_clk.common.hw,
+ [CLK_R_APB1_PPU] = &r_apb1_ppu_clk.common.hw,
+ [CLK_R_APB2_UART] = &r_apb2_uart_clk.common.hw,
+ [CLK_R_APB2_I2C0] = &r_apb2_i2c0_clk.common.hw,
+ [CLK_R_APB2_I2C1] = &r_apb2_i2c1_clk.common.hw,
+ [CLK_R_APB1_IR] = &r_apb1_ir_rx_clk.common.hw,
+ [CLK_R_APB1_BUS_IR] = &r_apb1_bus_ir_rx_clk.common.hw,
+ [CLK_R_AHB_BUS_RTC] = &r_ahb_bus_rtc_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_r_ccu_resets[] = {
+ [RST_R_APB1_TIMER] = { 0x11c, BIT(16) },
+ [RST_R_APB1_BUS_PWM] = { 0x13c, BIT(16) },
+ [RST_R_APB1_PPU] = { 0x17c, BIT(16) },
+ [RST_R_APB2_UART] = { 0x18c, BIT(16) },
+ [RST_R_APB2_I2C0] = { 0x19c, BIT(16) },
+ [RST_R_APB2_I2C1] = { 0x19c, BIT(17) },
+ [RST_R_APB1_BUS_IR] = { 0x1cc, BIT(16) },
+ [RST_R_AHB_BUS_RTC] = { 0x20c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_r_ccu_desc = {
+ .ccu_clks = sun50i_a100_r_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_r_ccu_clks),
+
+ .hw_clks = &sun50i_a100_r_hw_clks,
+
+ .resets = sun50i_a100_r_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_r_ccu_resets),
+};
+
+static int sun50i_a100_r_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc);
+}
+
+static const struct of_device_id sun50i_a100_r_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-r-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_r_ccu_driver = {
+ .probe = sun50i_a100_r_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-r-ccu",
+ .of_match_table = sun50i_a100_r_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_r_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
new file mode 100644
index 000000000000..3a8f187a51b7
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_R_H
+#define _CCU_SUN50I_A100_R_H
+
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+#define CLK_R_CPUS 0
+#define CLK_R_AHB 1
+
+/* exported except APB1 for R_PIO */
+
+#define CLK_R_APB2 3
+
+#define CLK_NUMBER (CLK_R_AHB_BUS_RTC + 1)
+
+#endif /* _CCU_SUN50I_A100_R_H */
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
new file mode 100644
index 000000000000..81b48c73d389
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
@@ -0,0 +1,1276 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100.h"
+
+#define SUN50I_A100_PLL_SDM_ENABLE BIT(24)
+#define SUN50I_A100_PLL_OUTPUT_ENABLE BIT(27)
+#define SUN50I_A100_PLL_LOCK BIT(28)
+#define SUN50I_A100_PLL_LOCK_ENABLE BIT(29)
+#define SUN50I_A100_PLL_ENABLE BIT(31)
+
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0 0xd1303333
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_A100_PLL_CPUX_REG 0x000
+static struct ccu_mult pll_cpux_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-cpux", "dcxo24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_A100_PLL_DDR0_REG 0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x010,
+ .hw.init = CLK_HW_INIT("pll-ddr0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE |
+ CLK_IS_CRITICAL),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH0_REG 0x020
+static struct ccu_nkmp pll_periph0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x020,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH1_REG 0x028
+static struct ccu_nkmp pll_periph1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph1", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0_REG 0x128
+
+#define SUN50I_A100_PLL_GPU_REG 0x030
+static struct ccu_nkmp pll_gpu_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x030,
+ .hw.init = CLK_HW_INIT("pll-gpu", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_A100_PLL_VIDEO0_REG 0x040
+static struct ccu_nm pll_video0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x040,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video0", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO1_REG 0x048
+static struct ccu_nm pll_video1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x048,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video1", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO2_REG 0x050
+static struct ccu_nm pll_video2_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x050,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video2", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VE_REG 0x058
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x058,
+ .hw.init = CLK_HW_INIT("pll-ve", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The COM PLL has m0 dividers in addition to the usual N, M
+ * factors. Since we only need 1 frequencies from this PLL: 45.1584 MHz,
+ * ignore it for now.
+ */
+#define SUN50I_A100_PLL_COM_REG 0x060
+static struct ccu_sdm_setting pll_com_sdm_table[] = {
+ { .rate = 451584000, .pattern = 0xc0014396, .m = 2, .n = 37 },
+};
+
+static struct ccu_nm pll_com_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(0, 1),
+ .sdm = _SUNXI_CCU_SDM(pll_com_sdm_table, BIT(24),
+ 0x160, BIT(31)),
+ .common = {
+ .reg = 0x060,
+ .features = CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-com", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO3_REG 0x068
+static struct ccu_nm pll_video3_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x068,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video3", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The Audio PLL has m0, m1 dividers in addition to the usual N, M
+ * factors. Since we only need 4 frequencies from this PLL: 22.5792 MHz,
+ * 24.576 MHz, 90.3168MHz and 98.304MHz ignore them for now.
+ * Enforce the default for them, which is m0 = 1, m1 = 0.
+ */
+#define SUN50I_A100_PLL_AUDIO_REG 0x078
+static struct ccu_sdm_setting pll_audio_sdm_table[] = {
+ { .rate = 45158400, .pattern = 0xc001bcd3, .m = 18, .n = 33 },
+ { .rate = 49152000, .pattern = 0xc001eb85, .m = 20, .n = 40 },
+ { .rate = 180633600, .pattern = 0xc001288d, .m = 3, .n = 22 },
+ { .rate = 196608000, .pattern = 0xc001eb85, .m = 5, .n = 40 },
+};
+
+static struct ccu_nm pll_audio_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(16, 6),
+ .fixed_post_div = 2,
+ .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, BIT(24),
+ 0x178, BIT(31)),
+ .common = {
+ .reg = 0x078,
+ .features = CCU_FEATURE_FIXED_POSTDIV |
+ CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-audio", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+static const char * const cpux_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-cpux",
+ "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+ psi_ahb1_ahb2_parents, 0x510,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "dcxo24M", "osc32k",
+ "psi-ahb1-ahb2",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const mbus_parents[] = { "dcxo24M", "pll-ddr0",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+ 0, 3, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-com", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de0", de_parents, 0x600,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+ 0x60c, BIT(0), 0);
+
+static const char * const g2d_parents[] = { "pll-com", "pll-periph0-2x",
+ "pll-video0-2x", "pll-video1-2x",
+ "pll-video2-2x"};
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d",
+ g2d_parents,
+ 0x630,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+ 0x63c, BIT(0), 0);
+
+static const char * const gpu_parents[] = { "pll-gpu" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents, 0x670,
+ 0, 2, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+ 0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "dcxo24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+ 0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+ 0, 3, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+ 0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+ 0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "psi-ahb1-ahb2",
+ 0x71c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "psi-ahb1-ahb2",
+ 0x72c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+ 0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "dcxo24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+ 0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+ 0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+ 0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+ 0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+ 0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+ 0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_csi_clk, "mbus-csi", "mbus",
+ 0x804, BIT(8), 0);
+static SUNXI_CCU_GATE(mbus_isp_clk, "mbus-isp", "mbus",
+ 0x804, BIT(9), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+ 0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+ 0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "dcxo24M",
+ "pll-periph0",
+ "pll-periph1",
+ "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", nand_spi_parents, 0x948,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb3", 0x96c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+ BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb3", 0x97c, BIT(0), 0);
+
+static const char * const ir_parents[] = { "osc32k", "iosc",
+ "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_rx_clk, "ir-rx", ir_parents, 0x990,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_rx_clk, "bus-ir-rx", "ahb3", 0x99c, BIT(0), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_tx_clk, "ir-tx", ir_parents, 0x9c0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_tx_clk, "bus-ir-tx", "apb1", 0x9cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1", 0x9ec, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio", "pll-com-audio" };
+static struct ccu_div i2s0_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa10,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s0",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s1_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa14,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s1",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s2_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa18,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s2",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s3_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa1c,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s3",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1", 0xa20, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1", 0xa20, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1", 0xa20, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2s3_clk, "bus-i2s3", "apb1", 0xa20, BIT(3), 0);
+
+static struct ccu_div spdif_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa24,
+ .hw.init = CLK_HW_INIT_PARENTS("spdif",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa40,
+ .hw.init = CLK_HW_INIT_PARENTS("dmic",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_dac_clk, "audio-codec-dac",
+ audio_parents, 0xa50,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_adc_clk, "audio-codec-adc",
+ audio_parents, 0xa54,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+ audio_parents, 0xa58,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+ BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for 2 USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_A100_USB0_CLK_REG 0xa70
+#define SUN50I_A100_USB1_CLK_REG 0xa74
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "dcxo24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "dcxo24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_lradc_clk, "bus-lradc", "ahb3", 0xa9c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top0_clk, "bus-dpss-top0", "ahb3",
+ 0xabc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top1_clk, "bus-dpss-top1", "ahb3",
+ 0xacc, BIT(0), 0);
+
+static const char * const mipi_dsi_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph0" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi",
+ mipi_dsi_parents,
+ 0xb24,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb3",
+ 0xb4c, BIT(0), 0);
+
+static const char * const tcon_lcd_parents[] = { "pll-video0-4x",
+ "pll-video1-4x",
+ "pll-video2-4x",
+ "pll-video3-4x",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_lcd_clk, "tcon-lcd0",
+ tcon_lcd_parents, 0xb60,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_tcon_lcd_clk, "bus-tcon-lcd0", "ahb3",
+ 0xb7c, BIT(0), 0);
+
+static const char * const ledc_parents[] = { "dcxo24M",
+ "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ledc_clk, "ledc",
+ ledc_parents, 0xbf0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ledc_clk, "bus-ledc", "ahb3", 0xbfc, BIT(0), 0);
+
+static const char * const csi_top_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_top_clk, "csi-top",
+ csi_top_parents, 0xc04,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi0_mclk_parents[] = { "dcxo24M", "pll-video2",
+ "pll-video3", "pll-video0",
+ "pll-video1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk",
+ csi0_mclk_parents, 0xc08,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi1_mclk_parents[] = { "dcxo24M", "pll-video3",
+ "pll-video0", "pll-video1",
+ "pll-video2" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk",
+ csi1_mclk_parents, 0xc0c,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb3", 0xc1c, BIT(0), 0);
+
+static const char * const csi_isp_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_isp_clk, "csi-isp",
+ csi_isp_parents, 0xc20,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_com_audio_clk, "pll-com-audio",
+ &pll_com_clk.common.hw,
+ 5, 1, CLK_SET_RATE_PARENT);
+
+static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x",
+ &pll_periph0_clk.common.hw,
+ 1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x",
+ &pll_periph1_clk.common.hw,
+ 1, 2, 0);
+
+static const struct clk_hw *pll_video0_parents[] = {
+ &pll_video0_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video0_4x_clk, "pll-video0-4x",
+ pll_video0_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video0_2x_clk, "pll-video0-2x",
+ pll_video0_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video1_parents[] = {
+ &pll_video1_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video1_4x_clk, "pll-video1-4x",
+ pll_video1_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video1_2x_clk, "pll-video1-2x",
+ pll_video1_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video2_parents[] = {
+ &pll_video2_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video2_4x_clk, "pll-video2-4x",
+ pll_video2_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video2_2x_clk, "pll-video2-2x",
+ pll_video2_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video3_parents[] = {
+ &pll_video3_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video3_4x_clk, "pll-video3-4x",
+ pll_video3_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video3_2x_clk, "pll-video3-2x",
+ pll_video3_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_a100_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_gpu_clk.common,
+ &pll_video0_clk.common,
+ &pll_video1_clk.common,
+ &pll_video2_clk.common,
+ &pll_video3_clk.common,
+ &pll_ve_clk.common,
+ &pll_com_clk.common,
+ &pll_audio_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &cpux_apb_clk.common,
+ &psi_ahb1_ahb2_clk.common,
+ &ahb3_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &mbus_clk.common,
+ &de_clk.common,
+ &bus_de_clk.common,
+ &g2d_clk.common,
+ &bus_g2d_clk.common,
+ &gpu_clk.common,
+ &bus_gpu_clk.common,
+ &ce_clk.common,
+ &bus_ce_clk.common,
+ &ve_clk.common,
+ &bus_ve_clk.common,
+ &bus_dma_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_hstimer_clk.common,
+ &avs_clk.common,
+ &bus_dbg_clk.common,
+ &bus_psi_clk.common,
+ &bus_pwm_clk.common,
+ &bus_iommu_clk.common,
+ &mbus_dma_clk.common,
+ &mbus_ve_clk.common,
+ &mbus_ce_clk.common,
+ &mbus_nand_clk.common,
+ &mbus_csi_clk.common,
+ &mbus_isp_clk.common,
+ &mbus_g2d_clk.common,
+ &bus_dram_clk.common,
+ &nand0_clk.common,
+ &nand1_clk.common,
+ &bus_nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &spi2_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_spi2_clk.common,
+ &emac_25m_clk.common,
+ &bus_emac_clk.common,
+ &ir_rx_clk.common,
+ &bus_ir_rx_clk.common,
+ &ir_tx_clk.common,
+ &bus_ir_tx_clk.common,
+ &bus_gpadc_clk.common,
+ &bus_ths_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &i2s3_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2s3_clk.common,
+ &spdif_clk.common,
+ &bus_spdif_clk.common,
+ &dmic_clk.common,
+ &bus_dmic_clk.common,
+ &audio_codec_dac_clk.common,
+ &audio_codec_adc_clk.common,
+ &audio_codec_4x_clk.common,
+ &bus_audio_codec_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_phy0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_phy1_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_otg_clk.common,
+ &bus_lradc_clk.common,
+ &bus_dpss_top0_clk.common,
+ &bus_dpss_top1_clk.common,
+ &mipi_dsi_clk.common,
+ &bus_mipi_dsi_clk.common,
+ &tcon_lcd_clk.common,
+ &bus_tcon_lcd_clk.common,
+ &ledc_clk.common,
+ &bus_ledc_clk.common,
+ &csi_top_clk.common,
+ &csi0_mclk_clk.common,
+ &csi1_mclk_clk.common,
+ &bus_csi_clk.common,
+ &csi_isp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_hw_clks = {
+ .hws = {
+ [CLK_OSC12M] = &osc12M_clk.hw,
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw,
+ [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw,
+ [CLK_PLL_VIDEO2_2X] = &pll_video2_2x_clk.hw,
+ [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw,
+ [CLK_PLL_VIDEO3] = &pll_video3_clk.common.hw,
+ [CLK_PLL_VIDEO3_2X] = &pll_video3_2x_clk.hw,
+ [CLK_PLL_VIDEO3_4X] = &pll_video3_4x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_COM] = &pll_com_clk.common.hw,
+ [CLK_PLL_COM_AUDIO] = &pll_com_audio_clk.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_CPUX_APB] = &cpux_apb_clk.common.hw,
+ [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw,
+ [CLK_AHB3] = &ahb3_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_G2D] = &g2d_clk.common.hw,
+ [CLK_BUS_G2D] = &bus_g2d_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_BUS_PSI] = &bus_psi_clk.common.hw,
+ [CLK_BUS_PWM] = &bus_pwm_clk.common.hw,
+ [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw,
+ [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw,
+ [CLK_MBUS_VE] = &mbus_ve_clk.common.hw,
+ [CLK_MBUS_CE] = &mbus_ce_clk.common.hw,
+ [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw,
+ [CLK_MBUS_CSI] = &mbus_csi_clk.common.hw,
+ [CLK_MBUS_ISP] = &mbus_isp_clk.common.hw,
+ [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_NAND0] = &nand0_clk.common.hw,
+ [CLK_NAND1] = &nand1_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
+ [CLK_EMAC_25M] = &emac_25m_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_IR_RX] = &ir_rx_clk.common.hw,
+ [CLK_BUS_IR_RX] = &bus_ir_rx_clk.common.hw,
+ [CLK_IR_TX] = &ir_tx_clk.common.hw,
+ [CLK_BUS_IR_TX] = &bus_ir_tx_clk.common.hw,
+ [CLK_BUS_GPADC] = &bus_gpadc_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_I2S3] = &i2s3_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2S3] = &bus_i2s3_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_DMIC] = &dmic_clk.common.hw,
+ [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw,
+ [CLK_AUDIO_DAC] = &audio_codec_dac_clk.common.hw,
+ [CLK_AUDIO_ADC] = &audio_codec_adc_clk.common.hw,
+ [CLK_AUDIO_4X] = &audio_codec_4x_clk.common.hw,
+ [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_LRADC] = &bus_lradc_clk.common.hw,
+ [CLK_BUS_DPSS_TOP0] = &bus_dpss_top0_clk.common.hw,
+ [CLK_BUS_DPSS_TOP1] = &bus_dpss_top1_clk.common.hw,
+ [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
+ [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
+ [CLK_TCON_LCD] = &tcon_lcd_clk.common.hw,
+ [CLK_BUS_TCON_LCD] = &bus_tcon_lcd_clk.common.hw,
+ [CLK_LEDC] = &ledc_clk.common.hw,
+ [CLK_BUS_LEDC] = &bus_ledc_clk.common.hw,
+ [CLK_CSI_TOP] = &csi_top_clk.common.hw,
+ [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
+ [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_CSI_ISP] = &csi_isp_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_ccu_resets[] = {
+ [RST_MBUS] = { 0x540, BIT(30) },
+
+ [RST_BUS_DE] = { 0x60c, BIT(16) },
+ [RST_BUS_G2D] = { 0x63c, BIT(16) },
+ [RST_BUS_GPU] = { 0x67c, BIT(16) },
+ [RST_BUS_CE] = { 0x68c, BIT(16) },
+ [RST_BUS_VE] = { 0x69c, BIT(16) },
+ [RST_BUS_DMA] = { 0x70c, BIT(16) },
+ [RST_BUS_MSGBOX] = { 0x71c, BIT(16) },
+ [RST_BUS_SPINLOCK] = { 0x72c, BIT(16) },
+ [RST_BUS_HSTIMER] = { 0x73c, BIT(16) },
+ [RST_BUS_DBG] = { 0x78c, BIT(16) },
+ [RST_BUS_PSI] = { 0x79c, BIT(16) },
+ [RST_BUS_PWM] = { 0x7ac, BIT(16) },
+ [RST_BUS_DRAM] = { 0x80c, BIT(16) },
+ [RST_BUS_NAND] = { 0x82c, BIT(16) },
+ [RST_BUS_MMC0] = { 0x84c, BIT(16) },
+ [RST_BUS_MMC1] = { 0x84c, BIT(17) },
+ [RST_BUS_MMC2] = { 0x84c, BIT(18) },
+ [RST_BUS_UART0] = { 0x90c, BIT(16) },
+ [RST_BUS_UART1] = { 0x90c, BIT(17) },
+ [RST_BUS_UART2] = { 0x90c, BIT(18) },
+ [RST_BUS_UART3] = { 0x90c, BIT(19) },
+ [RST_BUS_UART4] = { 0x90c, BIT(20) },
+ [RST_BUS_I2C0] = { 0x91c, BIT(16) },
+ [RST_BUS_I2C1] = { 0x91c, BIT(17) },
+ [RST_BUS_I2C2] = { 0x91c, BIT(18) },
+ [RST_BUS_I2C3] = { 0x91c, BIT(19) },
+ [RST_BUS_SPI0] = { 0x96c, BIT(16) },
+ [RST_BUS_SPI1] = { 0x96c, BIT(17) },
+ [RST_BUS_SPI2] = { 0x96c, BIT(18) },
+ [RST_BUS_EMAC] = { 0x97c, BIT(16) },
+ [RST_BUS_IR_RX] = { 0x99c, BIT(16) },
+ [RST_BUS_IR_TX] = { 0x9cc, BIT(16) },
+ [RST_BUS_GPADC] = { 0x9ec, BIT(16) },
+ [RST_BUS_THS] = { 0x9fc, BIT(16) },
+ [RST_BUS_I2S0] = { 0xa20, BIT(16) },
+ [RST_BUS_I2S1] = { 0xa20, BIT(17) },
+ [RST_BUS_I2S2] = { 0xa20, BIT(18) },
+ [RST_BUS_I2S3] = { 0xa20, BIT(19) },
+ [RST_BUS_SPDIF] = { 0xa2c, BIT(16) },
+ [RST_BUS_DMIC] = { 0xa4c, BIT(16) },
+ [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) },
+
+ [RST_USB_PHY0] = { 0xa70, BIT(30) },
+ [RST_USB_PHY1] = { 0xa74, BIT(30) },
+
+ [RST_BUS_OHCI0] = { 0xa8c, BIT(16) },
+ [RST_BUS_OHCI1] = { 0xa8c, BIT(17) },
+ [RST_BUS_EHCI0] = { 0xa8c, BIT(20) },
+ [RST_BUS_EHCI1] = { 0xa8c, BIT(21) },
+ [RST_BUS_OTG] = { 0xa8c, BIT(24) },
+
+ [RST_BUS_LRADC] = { 0xa9c, BIT(16) },
+ [RST_BUS_DPSS_TOP0] = { 0xabc, BIT(16) },
+ [RST_BUS_DPSS_TOP1] = { 0xacc, BIT(16) },
+ [RST_BUS_MIPI_DSI] = { 0xb4c, BIT(16) },
+ [RST_BUS_TCON_LCD] = { 0xb7c, BIT(16) },
+ [RST_BUS_LVDS] = { 0xbac, BIT(16) },
+ [RST_BUS_LEDC] = { 0xbfc, BIT(16) },
+ [RST_BUS_CSI] = { 0xc1c, BIT(16) },
+ [RST_BUS_CSI_ISP] = { 0xc2c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_ccu_desc = {
+ .ccu_clks = sun50i_a100_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_ccu_clks),
+
+ .hw_clks = &sun50i_a100_hw_clks,
+
+ .resets = sun50i_a100_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_ccu_resets),
+};
+
+static const u32 sun50i_a100_pll_regs[] = {
+ SUN50I_A100_PLL_CPUX_REG,
+ SUN50I_A100_PLL_DDR0_REG,
+ SUN50I_A100_PLL_PERIPH0_REG,
+ SUN50I_A100_PLL_PERIPH1_REG,
+ SUN50I_A100_PLL_GPU_REG,
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+ SUN50I_A100_PLL_VE_REG,
+ SUN50I_A100_PLL_COM_REG,
+ SUN50I_A100_PLL_AUDIO_REG,
+};
+
+static const u32 sun50i_a100_pll_video_regs[] = {
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+};
+
+static const u32 sun50i_a100_usb2_clk_regs[] = {
+ SUN50I_A100_USB0_CLK_REG,
+ SUN50I_A100_USB1_CLK_REG,
+};
+
+static struct ccu_pll_nb sun50i_a100_pll_cpu_nb = {
+ .common = &pll_cpux_clk.common,
+ /* copy from pll_cpux_clk */
+ .enable = BIT(27),
+ .lock = BIT(28),
+};
+
+static struct ccu_mux_nb sun50i_a100_cpu_nb = {
+ .common = &cpux_clk.common,
+ .cm = &cpux_clk.mux,
+ .delay_us = 1,
+ .bypass_index = 4, /* index of pll periph0 */
+};
+
+static int sun50i_a100_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+ u32 val;
+ int i, ret;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ /*
+ * Enable lock and enable bits on all PLLs.
+ *
+ * Due to the current design, multiple PLLs share one power switch,
+ * so switching PLL is easy to cause stability problems.
+ * When initializing, we enable them by default. When disable,
+ * we only turn off the output of PLL.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_regs[i]);
+ val |= SUN50I_A100_PLL_LOCK_ENABLE | SUN50I_A100_PLL_ENABLE;
+ writel(val, reg + sun50i_a100_pll_regs[i]);
+ }
+
+ /*
+ * In order to pass the EMI certification, the SDM function of
+ * the peripheral 1 bus is enabled, and the frequency is still
+ * calculated using the previous division factor.
+ */
+ writel(SUN50I_A100_PLL_PERIPH1_PATTERN0,
+ reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG);
+
+ val = readl(reg + SUN50I_A100_PLL_PERIPH1_REG);
+ val |= SUN50I_A100_PLL_SDM_ENABLE;
+ writel(val, reg + SUN50I_A100_PLL_PERIPH1_REG);
+
+ /*
+ * Force the output divider of video PLLs to 0.
+ *
+ * See the comment before pll-video0 definition for the reason.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_video_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_video_regs[i]);
+ val &= ~BIT(0);
+ writel(val, reg + sun50i_a100_pll_video_regs[i]);
+ }
+
+ /*
+ * Enforce m1 = 0, m0 = 1 for Audio PLL
+ *
+ * See the comment before pll-audio definition for the reason.
+ */
+ val = readl(reg + SUN50I_A100_PLL_AUDIO_REG);
+ val &= ~BIT(1);
+ val |= BIT(0);
+ writel(val, reg + SUN50I_A100_PLL_AUDIO_REG);
+
+ /*
+ * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+ *
+ * This clock mux is still mysterious, and the code just enforces
+ * it to have a valid clock parent.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_usb2_clk_regs); i++) {
+ val = readl(reg + sun50i_a100_usb2_clk_regs[i]);
+ val &= ~GENMASK(25, 24);
+ writel(val, reg + sun50i_a100_usb2_clk_regs[i]);
+ }
+
+ ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc);
+ if (ret)
+ return ret;
+
+ /* Gate then ungate PLL CPU after any rate changes */
+ ccu_pll_notifier_register(&sun50i_a100_pll_cpu_nb);
+
+ /* Reparent CPU during PLL CPU rate changes */
+ ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
+ &sun50i_a100_cpu_nb);
+
+ return 0;
+}
+
+static const struct of_device_id sun50i_a100_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_ccu_driver = {
+ .probe = sun50i_a100_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-ccu",
+ .of_match_table = sun50i_a100_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
new file mode 100644
index 000000000000..21ce92bb1d5f
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_H_
+#define _CCU_SUN50I_A100_H_
+
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+
+#define CLK_OSC12M 0
+#define CLK_PLL_CPUX 1
+#define CLK_PLL_DDR0 2
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X 4
+#define CLK_PLL_PERIPH1 5
+#define CLK_PLL_PERIPH1_2X 6
+#define CLK_PLL_GPU 7
+#define CLK_PLL_VIDEO0 8
+#define CLK_PLL_VIDEO0_2X 9
+#define CLK_PLL_VIDEO0_4X 10
+#define CLK_PLL_VIDEO1 11
+#define CLK_PLL_VIDEO1_2X 12
+#define CLK_PLL_VIDEO1_4X 13
+#define CLK_PLL_VIDEO2 14
+#define CLK_PLL_VIDEO2_2X 15
+#define CLK_PLL_VIDEO2_4X 16
+#define CLK_PLL_VIDEO3 17
+#define CLK_PLL_VIDEO3_2X 18
+#define CLK_PLL_VIDEO3_4X 19
+#define CLK_PLL_VE 20
+#define CLK_PLL_COM 21
+#define CLK_PLL_COM_AUDIO 22
+#define CLK_PLL_AUDIO 23
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI 25
+#define CLK_CPUX_APB 26
+#define CLK_PSI_AHB1_AHB2 27
+#define CLK_AHB3 28
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2 30
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_BUS_DRAM 58
+
+#define CLK_NUMBER (CLK_CSI_ISP + 1)
+
+#endif /* _CCU_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-ccu.h b/include/dt-bindings/clock/sun50i-a100-ccu.h
new file mode 100644
index 000000000000..28dc36e1a232
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-ccu.h
@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_H_
+
+#define CLK_PLL_PERIPH0 3
+
+#define CLK_CPUX 24
+
+#define CLK_APB1 29
+
+#define CLK_MBUS 31
+#define CLK_DE 32
+#define CLK_BUS_DE 33
+#define CLK_G2D 34
+#define CLK_BUS_G2D 35
+#define CLK_GPU 36
+#define CLK_BUS_GPU 37
+#define CLK_CE 38
+#define CLK_BUS_CE 39
+#define CLK_VE 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_DMA 42
+#define CLK_BUS_MSGBOX 43
+#define CLK_BUS_SPINLOCK 44
+#define CLK_BUS_HSTIMER 45
+#define CLK_AVS 46
+#define CLK_BUS_DBG 47
+#define CLK_BUS_PSI 48
+#define CLK_BUS_PWM 49
+#define CLK_BUS_IOMMU 50
+#define CLK_MBUS_DMA 51
+#define CLK_MBUS_VE 52
+#define CLK_MBUS_CE 53
+#define CLK_MBUS_NAND 54
+#define CLK_MBUS_CSI 55
+#define CLK_MBUS_ISP 56
+#define CLK_MBUS_G2D 57
+
+#define CLK_NAND0 59
+#define CLK_NAND1 60
+#define CLK_BUS_NAND 61
+#define CLK_MMC0 62
+#define CLK_MMC1 63
+#define CLK_MMC2 64
+#define CLK_MMC3 65
+#define CLK_BUS_MMC0 66
+#define CLK_BUS_MMC1 67
+#define CLK_BUS_MMC2 68
+#define CLK_BUS_UART0 69
+#define CLK_BUS_UART1 70
+#define CLK_BUS_UART2 71
+#define CLK_BUS_UART3 72
+#define CLK_BUS_UART4 73
+#define CLK_BUS_I2C0 74
+#define CLK_BUS_I2C1 75
+#define CLK_BUS_I2C2 76
+#define CLK_BUS_I2C3 77
+#define CLK_SPI0 78
+#define CLK_SPI1 79
+#define CLK_SPI2 80
+#define CLK_BUS_SPI0 81
+#define CLK_BUS_SPI1 82
+#define CLK_BUS_SPI2 83
+#define CLK_EMAC_25M 84
+#define CLK_BUS_EMAC 85
+#define CLK_IR_RX 86
+#define CLK_BUS_IR_RX 87
+#define CLK_IR_TX 88
+#define CLK_BUS_IR_TX 89
+#define CLK_BUS_GPADC 90
+#define CLK_BUS_THS 91
+#define CLK_I2S0 92
+#define CLK_I2S1 93
+#define CLK_I2S2 94
+#define CLK_I2S3 95
+#define CLK_BUS_I2S0 96
+#define CLK_BUS_I2S1 97
+#define CLK_BUS_I2S2 98
+#define CLK_BUS_I2S3 99
+#define CLK_SPDIF 100
+#define CLK_BUS_SPDIF 101
+#define CLK_DMIC 102
+#define CLK_BUS_DMIC 103
+#define CLK_AUDIO_DAC 104
+#define CLK_AUDIO_ADC 105
+#define CLK_AUDIO_4X 106
+#define CLK_BUS_AUDIO_CODEC 107
+#define CLK_USB_OHCI0 108
+#define CLK_USB_PHY0 109
+#define CLK_USB_OHCI1 110
+#define CLK_USB_PHY1 111
+#define CLK_BUS_OHCI0 112
+#define CLK_BUS_OHCI1 113
+#define CLK_BUS_EHCI0 114
+#define CLK_BUS_EHCI1 115
+#define CLK_BUS_OTG 116
+#define CLK_BUS_LRADC 117
+#define CLK_BUS_DPSS_TOP0 118
+#define CLK_BUS_DPSS_TOP1 119
+#define CLK_MIPI_DSI 120
+#define CLK_BUS_MIPI_DSI 121
+#define CLK_TCON_LCD 122
+#define CLK_BUS_TCON_LCD 123
+#define CLK_LEDC 124
+#define CLK_BUS_LEDC 125
+#define CLK_CSI_TOP 126
+#define CLK_CSI0_MCLK 127
+#define CLK_CSI1_MCLK 128
+#define CLK_BUS_CSI 129
+#define CLK_CSI_ISP 130
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-r-ccu.h b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
new file mode 100644
index 000000000000..07312e7264fb
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+
+#define CLK_R_APB1 2
+
+#define CLK_R_APB1_TIMER 4
+#define CLK_R_APB1_TWD 5
+#define CLK_R_APB1_PWM 6
+#define CLK_R_APB1_BUS_PWM 7
+#define CLK_R_APB1_PPU 8
+#define CLK_R_APB2_UART 9
+#define CLK_R_APB2_I2C0 10
+#define CLK_R_APB2_I2C1 11
+#define CLK_R_APB1_IR 12
+#define CLK_R_APB1_BUS_IR 13
+#define CLK_R_AHB_BUS_RTC 14
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-ccu.h b/include/dt-bindings/reset/sun50i-a100-ccu.h
new file mode 100644
index 000000000000..55c0ada99885
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-ccu.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_A100_H_
+#define _DT_BINDINGS_RESET_SUN50I_A100_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_G2D 2
+#define RST_BUS_GPU 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MSGBOX 7
+#define RST_BUS_SPINLOCK 8
+#define RST_BUS_HSTIMER 9
+#define RST_BUS_DBG 10
+#define RST_BUS_PSI 11
+#define RST_BUS_PWM 12
+#define RST_BUS_DRAM 13
+#define RST_BUS_NAND 14
+#define RST_BUS_MMC0 15
+#define RST_BUS_MMC1 16
+#define RST_BUS_MMC2 17
+#define RST_BUS_UART0 18
+#define RST_BUS_UART1 19
+#define RST_BUS_UART2 20
+#define RST_BUS_UART3 21
+#define RST_BUS_UART4 22
+#define RST_BUS_I2C0 23
+#define RST_BUS_I2C1 24
+#define RST_BUS_I2C2 25
+#define RST_BUS_I2C3 26
+#define RST_BUS_SPI0 27
+#define RST_BUS_SPI1 28
+#define RST_BUS_SPI2 29
+#define RST_BUS_EMAC 30
+#define RST_BUS_IR_RX 31
+#define RST_BUS_IR_TX 32
+#define RST_BUS_GPADC 33
+#define RST_BUS_THS 34
+#define RST_BUS_I2S0 35
+#define RST_BUS_I2S1 36
+#define RST_BUS_I2S2 37
+#define RST_BUS_I2S3 38
+#define RST_BUS_SPDIF 39
+#define RST_BUS_DMIC 40
+#define RST_BUS_AUDIO_CODEC 41
+#define RST_USB_PHY0 42
+#define RST_USB_PHY1 43
+#define RST_BUS_OHCI0 44
+#define RST_BUS_OHCI1 45
+#define RST_BUS_EHCI0 46
+#define RST_BUS_EHCI1 47
+#define RST_BUS_OTG 48
+#define RST_BUS_LRADC 49
+#define RST_BUS_DPSS_TOP0 50
+#define RST_BUS_DPSS_TOP1 51
+#define RST_BUS_MIPI_DSI 52
+#define RST_BUS_TCON_LCD 53
+#define RST_BUS_LVDS 54
+#define RST_BUS_LEDC 55
+#define RST_BUS_CSI 56
+#define RST_BUS_CSI_ISP 57
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-r-ccu.h b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
new file mode 100644
index 000000000000..737bf6f66626
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+
+#define RST_R_APB1_TIMER 0
+#define RST_R_APB1_BUS_PWM 1
+#define RST_R_APB1_PPU 2
+#define RST_R_APB2_UART 3
+#define RST_R_APB2_I2C0 4
+#define RST_R_APB2_I2C1 5
+#define RST_R_APB1_BUS_IR 6
+#define RST_R_AHB_BUS_RTC 7
+
+#endif /* _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ */
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
@ 2020-07-24 6:58 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 6:58 UTC (permalink / raw)
To: mturquette, sboyd, mripard, wens, robh+dt, p.zabel, linux-kernel,
linux-clk, linux-arm-kernel, devicetree
Cc: tiny.windzz, liyong, huangshuosheng, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
Add support for a100 in the sunxi-ng CCU framework.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 2 +
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++
drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
10 files changed, 1804 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index cdf333003c30..ce5f5847d5d3 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -17,6 +17,16 @@ config SUN50I_A64_CCU
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+config SUN50I_A100_CCU
+ bool "Support for the Allwinner A100 CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
+config SUN50I_A100_R_CCU
+ bool "Support for the Allwinner A100 PRCM CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
config SUN50I_H6_CCU
bool "Support for the Allwinner H6 CCU"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 4c7bee883f2f..3eb5cff40eac 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -23,6 +23,8 @@ obj-y += ccu_mp.o
# SoC support
obj-$(CONFIG_SUNIV_F1C100S_CCU) += ccu-suniv-f1c100s.o
obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
+obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o
+obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o
obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o
obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o
obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
new file mode 100644
index 000000000000..a56142b90993
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100-r.h"
+
+static const char * const cpus_r_apb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0" };
+static const struct ccu_mux_var_prediv cpus_r_apb2_predivs[] = {
+ { .index = 3, .shift = 0, .width = 5 },
+};
+
+static struct ccu_div r_cpus_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x000,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("cpus",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static CLK_FIXED_FACTOR_HW(r_ahb_clk, "r-ahb", &r_cpus_clk.common.hw, 1, 1, 0);
+
+static struct ccu_div r_apb1_clk = {
+ .div = _SUNXI_CCU_DIV(0, 2),
+
+ .common = {
+ .reg = 0x00c,
+ .hw.init = CLK_HW_INIT("r-apb1",
+ "r-ahb",
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct ccu_div r_apb2_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .var_predivs = cpus_r_apb2_predivs,
+ .n_var_predivs = ARRAY_SIZE(cpus_r_apb2_predivs),
+ },
+
+ .common = {
+ .reg = 0x010,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("r-apb2",
+ cpus_r_apb2_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static const struct clk_parent_data clk_parent_r_apb1[] = {
+ { .hw = &r_apb1_clk.common.hw },
+};
+
+static const struct clk_parent_data clk_parent_r_apb2[] = {
+ { .hw = &r_apb2_clk.common.hw },
+};
+
+static SUNXI_CCU_GATE_DATA(r_apb1_timer_clk, "r-apb1-timer", clk_parent_r_apb1,
+ 0x11c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_twd_clk, "r-apb1-twd", clk_parent_r_apb1,
+ 0x12c, BIT(0), 0);
+
+static const char * const r_apb1_pwm_clk_parents[] = { "dcxo24M", "osc32k",
+ "iosc" };
+static SUNXI_CCU_MUX(r_apb1_pwm_clk, "r-apb1-pwm", r_apb1_pwm_clk_parents,
+ 0x130, 24, 2, 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_pwm_clk, "r-apb1-bus-pwm",
+ clk_parent_r_apb1, 0x13c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_ppu_clk, "r-apb1-ppu", clk_parent_r_apb1,
+ 0x17c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_uart_clk, "r-apb2-uart", clk_parent_r_apb2,
+ 0x18c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c0_clk, "r-apb2-i2c0", clk_parent_r_apb2,
+ 0x19c, BIT(0), 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb2_i2c1_clk, "r-apb2-i2c1", clk_parent_r_apb2,
+ 0x19c, BIT(1), 0);
+
+static const char * const r_apb1_ir_rx_parents[] = { "osc32k", "dcxo24M" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(r_apb1_ir_rx_clk, "r-apb1-ir-rx",
+ r_apb1_ir_rx_parents, 0x1c0,
+ 0, 5, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE_DATA(r_apb1_bus_ir_rx_clk, "r-apb1-bus-ir-rx",
+ clk_parent_r_apb1, 0x1cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(r_ahb_bus_rtc_clk, "r-ahb-rtc", "r-ahb",
+ 0x20c, BIT(0), 0);
+
+static struct ccu_common *sun50i_a100_r_ccu_clks[] = {
+ &r_cpus_clk.common,
+ &r_apb1_clk.common,
+ &r_apb2_clk.common,
+ &r_apb1_timer_clk.common,
+ &r_apb1_twd_clk.common,
+ &r_apb1_pwm_clk.common,
+ &r_apb1_bus_pwm_clk.common,
+ &r_apb1_ppu_clk.common,
+ &r_apb2_uart_clk.common,
+ &r_apb2_i2c0_clk.common,
+ &r_apb2_i2c1_clk.common,
+ &r_apb1_ir_rx_clk.common,
+ &r_apb1_bus_ir_rx_clk.common,
+ &r_ahb_bus_rtc_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_r_hw_clks = {
+ .hws = {
+ [CLK_R_CPUS] = &r_cpus_clk.common.hw,
+ [CLK_R_AHB] = &r_ahb_clk.hw,
+ [CLK_R_APB1] = &r_apb1_clk.common.hw,
+ [CLK_R_APB2] = &r_apb2_clk.common.hw,
+ [CLK_R_APB1_TIMER] = &r_apb1_timer_clk.common.hw,
+ [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw,
+ [CLK_R_APB1_PWM] = &r_apb1_pwm_clk.common.hw,
+ [CLK_R_APB1_BUS_PWM] = &r_apb1_bus_pwm_clk.common.hw,
+ [CLK_R_APB1_PPU] = &r_apb1_ppu_clk.common.hw,
+ [CLK_R_APB2_UART] = &r_apb2_uart_clk.common.hw,
+ [CLK_R_APB2_I2C0] = &r_apb2_i2c0_clk.common.hw,
+ [CLK_R_APB2_I2C1] = &r_apb2_i2c1_clk.common.hw,
+ [CLK_R_APB1_IR] = &r_apb1_ir_rx_clk.common.hw,
+ [CLK_R_APB1_BUS_IR] = &r_apb1_bus_ir_rx_clk.common.hw,
+ [CLK_R_AHB_BUS_RTC] = &r_ahb_bus_rtc_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_r_ccu_resets[] = {
+ [RST_R_APB1_TIMER] = { 0x11c, BIT(16) },
+ [RST_R_APB1_BUS_PWM] = { 0x13c, BIT(16) },
+ [RST_R_APB1_PPU] = { 0x17c, BIT(16) },
+ [RST_R_APB2_UART] = { 0x18c, BIT(16) },
+ [RST_R_APB2_I2C0] = { 0x19c, BIT(16) },
+ [RST_R_APB2_I2C1] = { 0x19c, BIT(17) },
+ [RST_R_APB1_BUS_IR] = { 0x1cc, BIT(16) },
+ [RST_R_AHB_BUS_RTC] = { 0x20c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_r_ccu_desc = {
+ .ccu_clks = sun50i_a100_r_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_r_ccu_clks),
+
+ .hw_clks = &sun50i_a100_r_hw_clks,
+
+ .resets = sun50i_a100_r_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_r_ccu_resets),
+};
+
+static int sun50i_a100_r_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ return sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_r_ccu_desc);
+}
+
+static const struct of_device_id sun50i_a100_r_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-r-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_r_ccu_driver = {
+ .probe = sun50i_a100_r_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-r-ccu",
+ .of_match_table = sun50i_a100_r_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_r_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
new file mode 100644
index 000000000000..3a8f187a51b7
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_R_H
+#define _CCU_SUN50I_A100_R_H
+
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+#define CLK_R_CPUS 0
+#define CLK_R_AHB 1
+
+/* exported except APB1 for R_PIO */
+
+#define CLK_R_APB2 3
+
+#define CLK_NUMBER (CLK_R_AHB_BUS_RTC + 1)
+
+#endif /* _CCU_SUN50I_A100_R_H */
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.c b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
new file mode 100644
index 000000000000..81b48c73d389
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.c
@@ -0,0 +1,1276 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-a100.h"
+
+#define SUN50I_A100_PLL_SDM_ENABLE BIT(24)
+#define SUN50I_A100_PLL_OUTPUT_ENABLE BIT(27)
+#define SUN50I_A100_PLL_LOCK BIT(28)
+#define SUN50I_A100_PLL_LOCK_ENABLE BIT(29)
+#define SUN50I_A100_PLL_ENABLE BIT(31)
+
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0 0xd1303333
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_A100_PLL_CPUX_REG 0x000
+static struct ccu_mult pll_cpux_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-cpux", "dcxo24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_A100_PLL_DDR0_REG 0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x010,
+ .hw.init = CLK_HW_INIT("pll-ddr0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE |
+ CLK_IS_CRITICAL),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH0_REG 0x020
+static struct ccu_nkmp pll_periph0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x020,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph0", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_PERIPH1_REG 0x028
+static struct ccu_nkmp pll_periph1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph1", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+#define SUN50I_A100_PLL_PERIPH1_PATTERN0_REG 0x128
+
+#define SUN50I_A100_PLL_GPU_REG 0x030
+static struct ccu_nkmp pll_gpu_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x030,
+ .hw.init = CLK_HW_INIT("pll-gpu", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_A100_PLL_VIDEO0_REG 0x040
+static struct ccu_nm pll_video0_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x040,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video0", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO1_REG 0x048
+static struct ccu_nm pll_video1_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x048,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video1", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO2_REG 0x050
+static struct ccu_nm pll_video2_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x050,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video2", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VE_REG 0x058
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x058,
+ .hw.init = CLK_HW_INIT("pll-ve", "dcxo24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The COM PLL has m0 dividers in addition to the usual N, M
+ * factors. Since we only need 1 frequencies from this PLL: 45.1584 MHz,
+ * ignore it for now.
+ */
+#define SUN50I_A100_PLL_COM_REG 0x060
+static struct ccu_sdm_setting pll_com_sdm_table[] = {
+ { .rate = 451584000, .pattern = 0xc0014396, .m = 2, .n = 37 },
+};
+
+static struct ccu_nm pll_com_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(0, 1),
+ .sdm = _SUNXI_CCU_SDM(pll_com_sdm_table, BIT(24),
+ 0x160, BIT(31)),
+ .common = {
+ .reg = 0x060,
+ .features = CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-com", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_A100_PLL_VIDEO3_REG 0x068
+static struct ccu_nm pll_video3_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .common = {
+ .reg = 0x068,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video3", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * The Audio PLL has m0, m1 dividers in addition to the usual N, M
+ * factors. Since we only need 4 frequencies from this PLL: 22.5792 MHz,
+ * 24.576 MHz, 90.3168MHz and 98.304MHz ignore them for now.
+ * Enforce the default for them, which is m0 = 1, m1 = 0.
+ */
+#define SUN50I_A100_PLL_AUDIO_REG 0x078
+static struct ccu_sdm_setting pll_audio_sdm_table[] = {
+ { .rate = 45158400, .pattern = 0xc001bcd3, .m = 18, .n = 33 },
+ { .rate = 49152000, .pattern = 0xc001eb85, .m = 20, .n = 40 },
+ { .rate = 180633600, .pattern = 0xc001288d, .m = 3, .n = 22 },
+ { .rate = 196608000, .pattern = 0xc001eb85, .m = 5, .n = 40 },
+};
+
+static struct ccu_nm pll_audio_clk = {
+ .enable = SUN50I_A100_PLL_OUTPUT_ENABLE,
+ .lock = SUN50I_A100_PLL_LOCK,
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(16, 6),
+ .fixed_post_div = 2,
+ .sdm = _SUNXI_CCU_SDM(pll_audio_sdm_table, BIT(24),
+ 0x178, BIT(31)),
+ .common = {
+ .reg = 0x078,
+ .features = CCU_FEATURE_FIXED_POSTDIV |
+ CCU_FEATURE_SIGMA_DELTA_MOD,
+ .hw.init = CLK_HW_INIT("pll-audio", "dcxo24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+static const char * const cpux_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-cpux",
+ "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "dcxo24M", "osc32k",
+ "iosc", "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+ psi_ahb1_ahb2_parents, 0x510,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "dcxo24M", "osc32k",
+ "psi-ahb1-ahb2",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ 0);
+
+static const char * const mbus_parents[] = { "dcxo24M", "pll-ddr0",
+ "pll-periph0",
+ "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+ 0, 3, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-com", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de0", de_parents, 0x600,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+ 0x60c, BIT(0), 0);
+
+static const char * const g2d_parents[] = { "pll-com", "pll-periph0-2x",
+ "pll-video0-2x", "pll-video1-2x",
+ "pll-video2-2x"};
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d",
+ g2d_parents,
+ 0x630,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+ 0x63c, BIT(0), 0);
+
+static const char * const gpu_parents[] = { "pll-gpu" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents, 0x670,
+ 0, 2, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+ 0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "dcxo24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+ 0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+ 0, 3, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+ 0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+ 0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_msgbox_clk, "bus-msgbox", "psi-ahb1-ahb2",
+ 0x71c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_spinlock_clk, "bus-spinlock", "psi-ahb1-ahb2",
+ 0x72c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+ 0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "dcxo24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+ 0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+ 0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+ 0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+ 0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+ 0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+ 0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_csi_clk, "mbus-csi", "mbus",
+ 0x804, BIT(8), 0);
+static SUNXI_CCU_GATE(mbus_isp_clk, "mbus-isp", "mbus",
+ 0x804, BIT(9), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+ 0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+ 0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "dcxo24M",
+ "pll-periph0",
+ "pll-periph1",
+ "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ CLK_SET_RATE_NO_REPARENT);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", nand_spi_parents, 0x948,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb3", 0x96c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+ BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb3", 0x97c, BIT(0), 0);
+
+static const char * const ir_parents[] = { "osc32k", "iosc",
+ "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_rx_clk, "ir-rx", ir_parents, 0x990,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_rx_clk, "bus-ir-rx", "ahb3", 0x99c, BIT(0), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_tx_clk, "ir-tx", ir_parents, 0x9c0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ir_tx_clk, "bus-ir-tx", "apb1", 0x9cc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1", 0x9ec, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio", "pll-com-audio" };
+static struct ccu_div i2s0_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa10,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s0",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s1_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa14,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s1",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s2_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa18,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s2",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static struct ccu_div i2s3_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa1c,
+ .hw.init = CLK_HW_INIT_PARENTS("i2s3",
+ audio_parents,
+ &ccu_div_ops,
+ CLK_SET_RATE_PARENT),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1", 0xa20, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1", 0xa20, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1", 0xa20, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2s3_clk, "bus-i2s3", "apb1", 0xa20, BIT(3), 0);
+
+static struct ccu_div spdif_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa24,
+ .hw.init = CLK_HW_INIT_PARENTS("spdif",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa40,
+ .hw.init = CLK_HW_INIT_PARENTS("dmic",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_dac_clk, "audio-codec-dac",
+ audio_parents, 0xa50,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_adc_clk, "audio-codec-adc",
+ audio_parents, 0xa54,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+ audio_parents, 0xa58,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+ BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for 2 USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_A100_USB0_CLK_REG 0xa70
+#define SUN50I_A100_USB1_CLK_REG 0xa74
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "dcxo24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "dcxo24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_lradc_clk, "bus-lradc", "ahb3", 0xa9c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top0_clk, "bus-dpss-top0", "ahb3",
+ 0xabc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dpss_top1_clk, "bus-dpss-top1", "ahb3",
+ 0xacc, BIT(0), 0);
+
+static const char * const mipi_dsi_parents[] = { "dcxo24M", "pll-periph0-2x",
+ "pll-periph0" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi",
+ mipi_dsi_parents,
+ 0xb24,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb3",
+ 0xb4c, BIT(0), 0);
+
+static const char * const tcon_lcd_parents[] = { "pll-video0-4x",
+ "pll-video1-4x",
+ "pll-video2-4x",
+ "pll-video3-4x",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_lcd_clk, "tcon-lcd0",
+ tcon_lcd_parents, 0xb60,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_tcon_lcd_clk, "bus-tcon-lcd0", "ahb3",
+ 0xb7c, BIT(0), 0);
+
+static const char * const ledc_parents[] = { "dcxo24M",
+ "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ledc_clk, "ledc",
+ ledc_parents, 0xbf0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ledc_clk, "bus-ledc", "ahb3", 0xbfc, BIT(0), 0);
+
+static const char * const csi_top_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_top_clk, "csi-top",
+ csi_top_parents, 0xc04,
+ 0, 4, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi0_mclk_parents[] = { "dcxo24M", "pll-video2",
+ "pll-video3", "pll-video0",
+ "pll-video1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk",
+ csi0_mclk_parents, 0xc08,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const csi1_mclk_parents[] = { "dcxo24M", "pll-video3",
+ "pll-video0", "pll-video1",
+ "pll-video2" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk",
+ csi1_mclk_parents, 0xc0c,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb3", 0xc1c, BIT(0), 0);
+
+static const char * const csi_isp_parents[] = { "pll-periph0-2x",
+ "pll-video0-2x",
+ "pll-video1-2x",
+ "pll-video2-2x",
+ "pll-video3-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_isp_clk, "csi-isp",
+ csi_isp_parents, 0xc20,
+ 0, 5, /* M */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_com_audio_clk, "pll-com-audio",
+ &pll_com_clk.common.hw,
+ 5, 1, CLK_SET_RATE_PARENT);
+
+static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x",
+ &pll_periph0_clk.common.hw,
+ 1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x",
+ &pll_periph1_clk.common.hw,
+ 1, 2, 0);
+
+static const struct clk_hw *pll_video0_parents[] = {
+ &pll_video0_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video0_4x_clk, "pll-video0-4x",
+ pll_video0_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video0_2x_clk, "pll-video0-2x",
+ pll_video0_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video1_parents[] = {
+ &pll_video1_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video1_4x_clk, "pll-video1-4x",
+ pll_video1_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video1_2x_clk, "pll-video1-2x",
+ pll_video1_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video2_parents[] = {
+ &pll_video2_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video2_4x_clk, "pll-video2-4x",
+ pll_video2_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video2_2x_clk, "pll-video2-2x",
+ pll_video2_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_video3_parents[] = {
+ &pll_video3_clk.common.hw
+};
+static CLK_FIXED_FACTOR_HWS(pll_video3_4x_clk, "pll-video3-4x",
+ pll_video3_parents,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_video3_2x_clk, "pll-video3-2x",
+ pll_video3_parents,
+ 1, 2, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_a100_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_gpu_clk.common,
+ &pll_video0_clk.common,
+ &pll_video1_clk.common,
+ &pll_video2_clk.common,
+ &pll_video3_clk.common,
+ &pll_ve_clk.common,
+ &pll_com_clk.common,
+ &pll_audio_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &cpux_apb_clk.common,
+ &psi_ahb1_ahb2_clk.common,
+ &ahb3_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &mbus_clk.common,
+ &de_clk.common,
+ &bus_de_clk.common,
+ &g2d_clk.common,
+ &bus_g2d_clk.common,
+ &gpu_clk.common,
+ &bus_gpu_clk.common,
+ &ce_clk.common,
+ &bus_ce_clk.common,
+ &ve_clk.common,
+ &bus_ve_clk.common,
+ &bus_dma_clk.common,
+ &bus_msgbox_clk.common,
+ &bus_spinlock_clk.common,
+ &bus_hstimer_clk.common,
+ &avs_clk.common,
+ &bus_dbg_clk.common,
+ &bus_psi_clk.common,
+ &bus_pwm_clk.common,
+ &bus_iommu_clk.common,
+ &mbus_dma_clk.common,
+ &mbus_ve_clk.common,
+ &mbus_ce_clk.common,
+ &mbus_nand_clk.common,
+ &mbus_csi_clk.common,
+ &mbus_isp_clk.common,
+ &mbus_g2d_clk.common,
+ &bus_dram_clk.common,
+ &nand0_clk.common,
+ &nand1_clk.common,
+ &bus_nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &spi2_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_spi2_clk.common,
+ &emac_25m_clk.common,
+ &bus_emac_clk.common,
+ &ir_rx_clk.common,
+ &bus_ir_rx_clk.common,
+ &ir_tx_clk.common,
+ &bus_ir_tx_clk.common,
+ &bus_gpadc_clk.common,
+ &bus_ths_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &i2s3_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2s3_clk.common,
+ &spdif_clk.common,
+ &bus_spdif_clk.common,
+ &dmic_clk.common,
+ &bus_dmic_clk.common,
+ &audio_codec_dac_clk.common,
+ &audio_codec_adc_clk.common,
+ &audio_codec_4x_clk.common,
+ &bus_audio_codec_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_phy0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_phy1_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_otg_clk.common,
+ &bus_lradc_clk.common,
+ &bus_dpss_top0_clk.common,
+ &bus_dpss_top1_clk.common,
+ &mipi_dsi_clk.common,
+ &bus_mipi_dsi_clk.common,
+ &tcon_lcd_clk.common,
+ &bus_tcon_lcd_clk.common,
+ &ledc_clk.common,
+ &bus_ledc_clk.common,
+ &csi_top_clk.common,
+ &csi0_mclk_clk.common,
+ &csi1_mclk_clk.common,
+ &bus_csi_clk.common,
+ &csi_isp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_a100_hw_clks = {
+ .hws = {
+ [CLK_OSC12M] = &osc12M_clk.hw,
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw,
+ [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw,
+ [CLK_PLL_VIDEO2_2X] = &pll_video2_2x_clk.hw,
+ [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw,
+ [CLK_PLL_VIDEO3] = &pll_video3_clk.common.hw,
+ [CLK_PLL_VIDEO3_2X] = &pll_video3_2x_clk.hw,
+ [CLK_PLL_VIDEO3_4X] = &pll_video3_4x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_COM] = &pll_com_clk.common.hw,
+ [CLK_PLL_COM_AUDIO] = &pll_com_audio_clk.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.common.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_CPUX_APB] = &cpux_apb_clk.common.hw,
+ [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw,
+ [CLK_AHB3] = &ahb3_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_G2D] = &g2d_clk.common.hw,
+ [CLK_BUS_G2D] = &bus_g2d_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MSGBOX] = &bus_msgbox_clk.common.hw,
+ [CLK_BUS_SPINLOCK] = &bus_spinlock_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_BUS_PSI] = &bus_psi_clk.common.hw,
+ [CLK_BUS_PWM] = &bus_pwm_clk.common.hw,
+ [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw,
+ [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw,
+ [CLK_MBUS_VE] = &mbus_ve_clk.common.hw,
+ [CLK_MBUS_CE] = &mbus_ce_clk.common.hw,
+ [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw,
+ [CLK_MBUS_CSI] = &mbus_csi_clk.common.hw,
+ [CLK_MBUS_ISP] = &mbus_isp_clk.common.hw,
+ [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_NAND0] = &nand0_clk.common.hw,
+ [CLK_NAND1] = &nand1_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
+ [CLK_EMAC_25M] = &emac_25m_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_IR_RX] = &ir_rx_clk.common.hw,
+ [CLK_BUS_IR_RX] = &bus_ir_rx_clk.common.hw,
+ [CLK_IR_TX] = &ir_tx_clk.common.hw,
+ [CLK_BUS_IR_TX] = &bus_ir_tx_clk.common.hw,
+ [CLK_BUS_GPADC] = &bus_gpadc_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_I2S3] = &i2s3_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2S3] = &bus_i2s3_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_DMIC] = &dmic_clk.common.hw,
+ [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw,
+ [CLK_AUDIO_DAC] = &audio_codec_dac_clk.common.hw,
+ [CLK_AUDIO_ADC] = &audio_codec_adc_clk.common.hw,
+ [CLK_AUDIO_4X] = &audio_codec_4x_clk.common.hw,
+ [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_LRADC] = &bus_lradc_clk.common.hw,
+ [CLK_BUS_DPSS_TOP0] = &bus_dpss_top0_clk.common.hw,
+ [CLK_BUS_DPSS_TOP1] = &bus_dpss_top1_clk.common.hw,
+ [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
+ [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
+ [CLK_TCON_LCD] = &tcon_lcd_clk.common.hw,
+ [CLK_BUS_TCON_LCD] = &bus_tcon_lcd_clk.common.hw,
+ [CLK_LEDC] = &ledc_clk.common.hw,
+ [CLK_BUS_LEDC] = &bus_ledc_clk.common.hw,
+ [CLK_CSI_TOP] = &csi_top_clk.common.hw,
+ [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
+ [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
+ [CLK_BUS_CSI] = &bus_csi_clk.common.hw,
+ [CLK_CSI_ISP] = &csi_isp_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_a100_ccu_resets[] = {
+ [RST_MBUS] = { 0x540, BIT(30) },
+
+ [RST_BUS_DE] = { 0x60c, BIT(16) },
+ [RST_BUS_G2D] = { 0x63c, BIT(16) },
+ [RST_BUS_GPU] = { 0x67c, BIT(16) },
+ [RST_BUS_CE] = { 0x68c, BIT(16) },
+ [RST_BUS_VE] = { 0x69c, BIT(16) },
+ [RST_BUS_DMA] = { 0x70c, BIT(16) },
+ [RST_BUS_MSGBOX] = { 0x71c, BIT(16) },
+ [RST_BUS_SPINLOCK] = { 0x72c, BIT(16) },
+ [RST_BUS_HSTIMER] = { 0x73c, BIT(16) },
+ [RST_BUS_DBG] = { 0x78c, BIT(16) },
+ [RST_BUS_PSI] = { 0x79c, BIT(16) },
+ [RST_BUS_PWM] = { 0x7ac, BIT(16) },
+ [RST_BUS_DRAM] = { 0x80c, BIT(16) },
+ [RST_BUS_NAND] = { 0x82c, BIT(16) },
+ [RST_BUS_MMC0] = { 0x84c, BIT(16) },
+ [RST_BUS_MMC1] = { 0x84c, BIT(17) },
+ [RST_BUS_MMC2] = { 0x84c, BIT(18) },
+ [RST_BUS_UART0] = { 0x90c, BIT(16) },
+ [RST_BUS_UART1] = { 0x90c, BIT(17) },
+ [RST_BUS_UART2] = { 0x90c, BIT(18) },
+ [RST_BUS_UART3] = { 0x90c, BIT(19) },
+ [RST_BUS_UART4] = { 0x90c, BIT(20) },
+ [RST_BUS_I2C0] = { 0x91c, BIT(16) },
+ [RST_BUS_I2C1] = { 0x91c, BIT(17) },
+ [RST_BUS_I2C2] = { 0x91c, BIT(18) },
+ [RST_BUS_I2C3] = { 0x91c, BIT(19) },
+ [RST_BUS_SPI0] = { 0x96c, BIT(16) },
+ [RST_BUS_SPI1] = { 0x96c, BIT(17) },
+ [RST_BUS_SPI2] = { 0x96c, BIT(18) },
+ [RST_BUS_EMAC] = { 0x97c, BIT(16) },
+ [RST_BUS_IR_RX] = { 0x99c, BIT(16) },
+ [RST_BUS_IR_TX] = { 0x9cc, BIT(16) },
+ [RST_BUS_GPADC] = { 0x9ec, BIT(16) },
+ [RST_BUS_THS] = { 0x9fc, BIT(16) },
+ [RST_BUS_I2S0] = { 0xa20, BIT(16) },
+ [RST_BUS_I2S1] = { 0xa20, BIT(17) },
+ [RST_BUS_I2S2] = { 0xa20, BIT(18) },
+ [RST_BUS_I2S3] = { 0xa20, BIT(19) },
+ [RST_BUS_SPDIF] = { 0xa2c, BIT(16) },
+ [RST_BUS_DMIC] = { 0xa4c, BIT(16) },
+ [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) },
+
+ [RST_USB_PHY0] = { 0xa70, BIT(30) },
+ [RST_USB_PHY1] = { 0xa74, BIT(30) },
+
+ [RST_BUS_OHCI0] = { 0xa8c, BIT(16) },
+ [RST_BUS_OHCI1] = { 0xa8c, BIT(17) },
+ [RST_BUS_EHCI0] = { 0xa8c, BIT(20) },
+ [RST_BUS_EHCI1] = { 0xa8c, BIT(21) },
+ [RST_BUS_OTG] = { 0xa8c, BIT(24) },
+
+ [RST_BUS_LRADC] = { 0xa9c, BIT(16) },
+ [RST_BUS_DPSS_TOP0] = { 0xabc, BIT(16) },
+ [RST_BUS_DPSS_TOP1] = { 0xacc, BIT(16) },
+ [RST_BUS_MIPI_DSI] = { 0xb4c, BIT(16) },
+ [RST_BUS_TCON_LCD] = { 0xb7c, BIT(16) },
+ [RST_BUS_LVDS] = { 0xbac, BIT(16) },
+ [RST_BUS_LEDC] = { 0xbfc, BIT(16) },
+ [RST_BUS_CSI] = { 0xc1c, BIT(16) },
+ [RST_BUS_CSI_ISP] = { 0xc2c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_a100_ccu_desc = {
+ .ccu_clks = sun50i_a100_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_a100_ccu_clks),
+
+ .hw_clks = &sun50i_a100_hw_clks,
+
+ .resets = sun50i_a100_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_a100_ccu_resets),
+};
+
+static const u32 sun50i_a100_pll_regs[] = {
+ SUN50I_A100_PLL_CPUX_REG,
+ SUN50I_A100_PLL_DDR0_REG,
+ SUN50I_A100_PLL_PERIPH0_REG,
+ SUN50I_A100_PLL_PERIPH1_REG,
+ SUN50I_A100_PLL_GPU_REG,
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+ SUN50I_A100_PLL_VE_REG,
+ SUN50I_A100_PLL_COM_REG,
+ SUN50I_A100_PLL_AUDIO_REG,
+};
+
+static const u32 sun50i_a100_pll_video_regs[] = {
+ SUN50I_A100_PLL_VIDEO0_REG,
+ SUN50I_A100_PLL_VIDEO1_REG,
+ SUN50I_A100_PLL_VIDEO2_REG,
+ SUN50I_A100_PLL_VIDEO3_REG,
+};
+
+static const u32 sun50i_a100_usb2_clk_regs[] = {
+ SUN50I_A100_USB0_CLK_REG,
+ SUN50I_A100_USB1_CLK_REG,
+};
+
+static struct ccu_pll_nb sun50i_a100_pll_cpu_nb = {
+ .common = &pll_cpux_clk.common,
+ /* copy from pll_cpux_clk */
+ .enable = BIT(27),
+ .lock = BIT(28),
+};
+
+static struct ccu_mux_nb sun50i_a100_cpu_nb = {
+ .common = &cpux_clk.common,
+ .cm = &cpux_clk.mux,
+ .delay_us = 1,
+ .bypass_index = 4, /* index of pll periph0 */
+};
+
+static int sun50i_a100_ccu_probe(struct platform_device *pdev)
+{
+ void __iomem *reg;
+ u32 val;
+ int i, ret;
+
+ reg = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ /*
+ * Enable lock and enable bits on all PLLs.
+ *
+ * Due to the current design, multiple PLLs share one power switch,
+ * so switching PLL is easy to cause stability problems.
+ * When initializing, we enable them by default. When disable,
+ * we only turn off the output of PLL.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_regs[i]);
+ val |= SUN50I_A100_PLL_LOCK_ENABLE | SUN50I_A100_PLL_ENABLE;
+ writel(val, reg + sun50i_a100_pll_regs[i]);
+ }
+
+ /*
+ * In order to pass the EMI certification, the SDM function of
+ * the peripheral 1 bus is enabled, and the frequency is still
+ * calculated using the previous division factor.
+ */
+ writel(SUN50I_A100_PLL_PERIPH1_PATTERN0,
+ reg + SUN50I_A100_PLL_PERIPH1_PATTERN0_REG);
+
+ val = readl(reg + SUN50I_A100_PLL_PERIPH1_REG);
+ val |= SUN50I_A100_PLL_SDM_ENABLE;
+ writel(val, reg + SUN50I_A100_PLL_PERIPH1_REG);
+
+ /*
+ * Force the output divider of video PLLs to 0.
+ *
+ * See the comment before pll-video0 definition for the reason.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_pll_video_regs); i++) {
+ val = readl(reg + sun50i_a100_pll_video_regs[i]);
+ val &= ~BIT(0);
+ writel(val, reg + sun50i_a100_pll_video_regs[i]);
+ }
+
+ /*
+ * Enforce m1 = 0, m0 = 1 for Audio PLL
+ *
+ * See the comment before pll-audio definition for the reason.
+ */
+ val = readl(reg + SUN50I_A100_PLL_AUDIO_REG);
+ val &= ~BIT(1);
+ val |= BIT(0);
+ writel(val, reg + SUN50I_A100_PLL_AUDIO_REG);
+
+ /*
+ * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+ *
+ * This clock mux is still mysterious, and the code just enforces
+ * it to have a valid clock parent.
+ */
+ for (i = 0; i < ARRAY_SIZE(sun50i_a100_usb2_clk_regs); i++) {
+ val = readl(reg + sun50i_a100_usb2_clk_regs[i]);
+ val &= ~GENMASK(25, 24);
+ writel(val, reg + sun50i_a100_usb2_clk_regs[i]);
+ }
+
+ ret = sunxi_ccu_probe(pdev->dev.of_node, reg, &sun50i_a100_ccu_desc);
+ if (ret)
+ return ret;
+
+ /* Gate then ungate PLL CPU after any rate changes */
+ ccu_pll_notifier_register(&sun50i_a100_pll_cpu_nb);
+
+ /* Reparent CPU during PLL CPU rate changes */
+ ccu_mux_notifier_register(pll_cpux_clk.common.hw.clk,
+ &sun50i_a100_cpu_nb);
+
+ return 0;
+}
+
+static const struct of_device_id sun50i_a100_ccu_ids[] = {
+ { .compatible = "allwinner,sun50i-a100-ccu" },
+ { }
+};
+
+static struct platform_driver sun50i_a100_ccu_driver = {
+ .probe = sun50i_a100_ccu_probe,
+ .driver = {
+ .name = "sun50i-a100-ccu",
+ .of_match_table = sun50i_a100_ccu_ids,
+ },
+};
+module_platform_driver(sun50i_a100_ccu_driver);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-a100.h b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
new file mode 100644
index 000000000000..21ce92bb1d5f
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-a100.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _CCU_SUN50I_A100_H_
+#define _CCU_SUN50I_A100_H_
+
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+
+#define CLK_OSC12M 0
+#define CLK_PLL_CPUX 1
+#define CLK_PLL_DDR0 2
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X 4
+#define CLK_PLL_PERIPH1 5
+#define CLK_PLL_PERIPH1_2X 6
+#define CLK_PLL_GPU 7
+#define CLK_PLL_VIDEO0 8
+#define CLK_PLL_VIDEO0_2X 9
+#define CLK_PLL_VIDEO0_4X 10
+#define CLK_PLL_VIDEO1 11
+#define CLK_PLL_VIDEO1_2X 12
+#define CLK_PLL_VIDEO1_4X 13
+#define CLK_PLL_VIDEO2 14
+#define CLK_PLL_VIDEO2_2X 15
+#define CLK_PLL_VIDEO2_4X 16
+#define CLK_PLL_VIDEO3 17
+#define CLK_PLL_VIDEO3_2X 18
+#define CLK_PLL_VIDEO3_4X 19
+#define CLK_PLL_VE 20
+#define CLK_PLL_COM 21
+#define CLK_PLL_COM_AUDIO 22
+#define CLK_PLL_AUDIO 23
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI 25
+#define CLK_CPUX_APB 26
+#define CLK_PSI_AHB1_AHB2 27
+#define CLK_AHB3 28
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2 30
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_BUS_DRAM 58
+
+#define CLK_NUMBER (CLK_CSI_ISP + 1)
+
+#endif /* _CCU_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-ccu.h b/include/dt-bindings/clock/sun50i-a100-ccu.h
new file mode 100644
index 000000000000..28dc36e1a232
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-ccu.h
@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_H_
+
+#define CLK_PLL_PERIPH0 3
+
+#define CLK_CPUX 24
+
+#define CLK_APB1 29
+
+#define CLK_MBUS 31
+#define CLK_DE 32
+#define CLK_BUS_DE 33
+#define CLK_G2D 34
+#define CLK_BUS_G2D 35
+#define CLK_GPU 36
+#define CLK_BUS_GPU 37
+#define CLK_CE 38
+#define CLK_BUS_CE 39
+#define CLK_VE 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_DMA 42
+#define CLK_BUS_MSGBOX 43
+#define CLK_BUS_SPINLOCK 44
+#define CLK_BUS_HSTIMER 45
+#define CLK_AVS 46
+#define CLK_BUS_DBG 47
+#define CLK_BUS_PSI 48
+#define CLK_BUS_PWM 49
+#define CLK_BUS_IOMMU 50
+#define CLK_MBUS_DMA 51
+#define CLK_MBUS_VE 52
+#define CLK_MBUS_CE 53
+#define CLK_MBUS_NAND 54
+#define CLK_MBUS_CSI 55
+#define CLK_MBUS_ISP 56
+#define CLK_MBUS_G2D 57
+
+#define CLK_NAND0 59
+#define CLK_NAND1 60
+#define CLK_BUS_NAND 61
+#define CLK_MMC0 62
+#define CLK_MMC1 63
+#define CLK_MMC2 64
+#define CLK_MMC3 65
+#define CLK_BUS_MMC0 66
+#define CLK_BUS_MMC1 67
+#define CLK_BUS_MMC2 68
+#define CLK_BUS_UART0 69
+#define CLK_BUS_UART1 70
+#define CLK_BUS_UART2 71
+#define CLK_BUS_UART3 72
+#define CLK_BUS_UART4 73
+#define CLK_BUS_I2C0 74
+#define CLK_BUS_I2C1 75
+#define CLK_BUS_I2C2 76
+#define CLK_BUS_I2C3 77
+#define CLK_SPI0 78
+#define CLK_SPI1 79
+#define CLK_SPI2 80
+#define CLK_BUS_SPI0 81
+#define CLK_BUS_SPI1 82
+#define CLK_BUS_SPI2 83
+#define CLK_EMAC_25M 84
+#define CLK_BUS_EMAC 85
+#define CLK_IR_RX 86
+#define CLK_BUS_IR_RX 87
+#define CLK_IR_TX 88
+#define CLK_BUS_IR_TX 89
+#define CLK_BUS_GPADC 90
+#define CLK_BUS_THS 91
+#define CLK_I2S0 92
+#define CLK_I2S1 93
+#define CLK_I2S2 94
+#define CLK_I2S3 95
+#define CLK_BUS_I2S0 96
+#define CLK_BUS_I2S1 97
+#define CLK_BUS_I2S2 98
+#define CLK_BUS_I2S3 99
+#define CLK_SPDIF 100
+#define CLK_BUS_SPDIF 101
+#define CLK_DMIC 102
+#define CLK_BUS_DMIC 103
+#define CLK_AUDIO_DAC 104
+#define CLK_AUDIO_ADC 105
+#define CLK_AUDIO_4X 106
+#define CLK_BUS_AUDIO_CODEC 107
+#define CLK_USB_OHCI0 108
+#define CLK_USB_PHY0 109
+#define CLK_USB_OHCI1 110
+#define CLK_USB_PHY1 111
+#define CLK_BUS_OHCI0 112
+#define CLK_BUS_OHCI1 113
+#define CLK_BUS_EHCI0 114
+#define CLK_BUS_EHCI1 115
+#define CLK_BUS_OTG 116
+#define CLK_BUS_LRADC 117
+#define CLK_BUS_DPSS_TOP0 118
+#define CLK_BUS_DPSS_TOP1 119
+#define CLK_MIPI_DSI 120
+#define CLK_BUS_MIPI_DSI 121
+#define CLK_TCON_LCD 122
+#define CLK_BUS_TCON_LCD 123
+#define CLK_LEDC 124
+#define CLK_BUS_LEDC 125
+#define CLK_CSI_TOP 126
+#define CLK_CSI0_MCLK 127
+#define CLK_CSI1_MCLK 128
+#define CLK_BUS_CSI 129
+#define CLK_CSI_ISP 130
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/clock/sun50i-a100-r-ccu.h b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
new file mode 100644
index 000000000000..07312e7264fb
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-a100-r-ccu.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_
+
+#define CLK_R_APB1 2
+
+#define CLK_R_APB1_TIMER 4
+#define CLK_R_APB1_TWD 5
+#define CLK_R_APB1_PWM 6
+#define CLK_R_APB1_BUS_PWM 7
+#define CLK_R_APB1_PPU 8
+#define CLK_R_APB2_UART 9
+#define CLK_R_APB2_I2C0 10
+#define CLK_R_APB2_I2C1 11
+#define CLK_R_APB1_IR 12
+#define CLK_R_APB1_BUS_IR 13
+#define CLK_R_AHB_BUS_RTC 14
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_A100_R_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-ccu.h b/include/dt-bindings/reset/sun50i-a100-ccu.h
new file mode 100644
index 000000000000..55c0ada99885
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-ccu.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_A100_H_
+#define _DT_BINDINGS_RESET_SUN50I_A100_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_G2D 2
+#define RST_BUS_GPU 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MSGBOX 7
+#define RST_BUS_SPINLOCK 8
+#define RST_BUS_HSTIMER 9
+#define RST_BUS_DBG 10
+#define RST_BUS_PSI 11
+#define RST_BUS_PWM 12
+#define RST_BUS_DRAM 13
+#define RST_BUS_NAND 14
+#define RST_BUS_MMC0 15
+#define RST_BUS_MMC1 16
+#define RST_BUS_MMC2 17
+#define RST_BUS_UART0 18
+#define RST_BUS_UART1 19
+#define RST_BUS_UART2 20
+#define RST_BUS_UART3 21
+#define RST_BUS_UART4 22
+#define RST_BUS_I2C0 23
+#define RST_BUS_I2C1 24
+#define RST_BUS_I2C2 25
+#define RST_BUS_I2C3 26
+#define RST_BUS_SPI0 27
+#define RST_BUS_SPI1 28
+#define RST_BUS_SPI2 29
+#define RST_BUS_EMAC 30
+#define RST_BUS_IR_RX 31
+#define RST_BUS_IR_TX 32
+#define RST_BUS_GPADC 33
+#define RST_BUS_THS 34
+#define RST_BUS_I2S0 35
+#define RST_BUS_I2S1 36
+#define RST_BUS_I2S2 37
+#define RST_BUS_I2S3 38
+#define RST_BUS_SPDIF 39
+#define RST_BUS_DMIC 40
+#define RST_BUS_AUDIO_CODEC 41
+#define RST_USB_PHY0 42
+#define RST_USB_PHY1 43
+#define RST_BUS_OHCI0 44
+#define RST_BUS_OHCI1 45
+#define RST_BUS_EHCI0 46
+#define RST_BUS_EHCI1 47
+#define RST_BUS_OTG 48
+#define RST_BUS_LRADC 49
+#define RST_BUS_DPSS_TOP0 50
+#define RST_BUS_DPSS_TOP1 51
+#define RST_BUS_MIPI_DSI 52
+#define RST_BUS_TCON_LCD 53
+#define RST_BUS_LVDS 54
+#define RST_BUS_LEDC 55
+#define RST_BUS_CSI 56
+#define RST_BUS_CSI_ISP 57
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_A100_H_ */
diff --git a/include/dt-bindings/reset/sun50i-a100-r-ccu.h b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
new file mode 100644
index 000000000000..737bf6f66626
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-a100-r-ccu.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_
+
+#define RST_R_APB1_TIMER 0
+#define RST_R_APB1_BUS_PWM 1
+#define RST_R_APB1_PPU 2
+#define RST_R_APB2_UART 3
+#define RST_R_APB2_I2C0 4
+#define RST_R_APB2_I2C1 5
+#define RST_R_APB1_BUS_IR 6
+#define RST_R_AHB_BUS_RTC 7
+
+#endif /* _DT_BINDINGS_RST_SUN50I_A100_R_CCU_H_ */
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 03/16] dt-bindings: pinctrl: sunxi: Get rid of continual nesting
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:00 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:00 UTC (permalink / raw)
To: linus.walleij, robh+dt, mripard, wens
Cc: linux-gpio, devicetree, linux-arm-kernel, linux-kernel,
tiny.windzz, huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Rather than a continual nesting of 'else' clauses, just make
each 'if' a new entry under 'allOf' and get rid of the else.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 124 ++++++++++--------
1 file changed, 68 insertions(+), 56 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 7556be6e2754..35a26abb02e7 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -155,62 +155,74 @@ allOf:
minItems: 5
maxItems: 5
- else:
- if:
- properties:
- compatible:
- enum:
- - allwinner,sun6i-a31-pinctrl
- - allwinner,sun6i-a31s-pinctrl
- - allwinner,sun50i-h6-pinctrl
-
- then:
- properties:
- interrupts:
- minItems: 4
- maxItems: 4
-
- else:
- if:
- properties:
- compatible:
- enum:
- - allwinner,sun8i-a23-pinctrl
- - allwinner,sun8i-a83t-pinctrl
- - allwinner,sun50i-a64-pinctrl
- - allwinner,sun50i-h5-pinctrl
- - allwinner,suniv-f1c100s-pinctrl
-
- then:
- properties:
- interrupts:
- minItems: 3
- maxItems: 3
-
- else:
- if:
- properties:
- compatible:
- enum:
- - allwinner,sun6i-a31-r-pinctrl
- - allwinner,sun8i-a33-pinctrl
- - allwinner,sun8i-h3-pinctrl
- - allwinner,sun8i-v3-pinctrl
- - allwinner,sun8i-v3s-pinctrl
- - allwinner,sun9i-a80-r-pinctrl
- - allwinner,sun50i-h6-r-pinctrl
-
- then:
- properties:
- interrupts:
- minItems: 2
- maxItems: 2
-
- else:
- properties:
- interrupts:
- minItems: 1
- maxItems: 1
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun6i-a31-pinctrl
+ - allwinner,sun6i-a31s-pinctrl
+ - allwinner,sun50i-h6-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 4
+ maxItems: 4
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun8i-a23-pinctrl
+ - allwinner,sun8i-a83t-pinctrl
+ - allwinner,sun50i-a64-pinctrl
+ - allwinner,sun50i-h5-pinctrl
+ - allwinner,suniv-f1c100s-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 3
+ maxItems: 3
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun6i-a31-r-pinctrl
+ - allwinner,sun8i-a33-pinctrl
+ - allwinner,sun8i-h3-pinctrl
+ - allwinner,sun8i-v3-pinctrl
+ - allwinner,sun8i-v3s-pinctrl
+ - allwinner,sun9i-a80-r-pinctrl
+ - allwinner,sun50i-h6-r-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun4i-a10-pinctrl
+ - allwinner,sun5i-a10s-pinctrl
+ - allwinner,sun5i-a13-pinctrl
+ - allwinner,sun7i-a20-pinctrl
+ - allwinner,sun8i-a23-r-pinctrl
+ - allwinner,sun8i-a83t-r-pinctrl
+ - allwinner,sun8i-h3-r-pinctrl
+ - allwinner,sun8i-r40-pinctrl
+ - allwinner,sun50i-a64-r-pinctrl
+ - nextthing,gr8-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
additionalProperties: false
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 03/16] dt-bindings: pinctrl: sunxi: Get rid of continual nesting
@ 2020-07-24 7:00 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:00 UTC (permalink / raw)
To: linus.walleij, robh+dt, mripard, wens
Cc: devicetree, liyong, tiny.windzz, linux-kernel, linux-gpio,
huangshuosheng, Yangtao Li, Rob Herring, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Rather than a continual nesting of 'else' clauses, just make
each 'if' a new entry under 'allOf' and get rid of the else.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 124 ++++++++++--------
1 file changed, 68 insertions(+), 56 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 7556be6e2754..35a26abb02e7 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -155,62 +155,74 @@ allOf:
minItems: 5
maxItems: 5
- else:
- if:
- properties:
- compatible:
- enum:
- - allwinner,sun6i-a31-pinctrl
- - allwinner,sun6i-a31s-pinctrl
- - allwinner,sun50i-h6-pinctrl
-
- then:
- properties:
- interrupts:
- minItems: 4
- maxItems: 4
-
- else:
- if:
- properties:
- compatible:
- enum:
- - allwinner,sun8i-a23-pinctrl
- - allwinner,sun8i-a83t-pinctrl
- - allwinner,sun50i-a64-pinctrl
- - allwinner,sun50i-h5-pinctrl
- - allwinner,suniv-f1c100s-pinctrl
-
- then:
- properties:
- interrupts:
- minItems: 3
- maxItems: 3
-
- else:
- if:
- properties:
- compatible:
- enum:
- - allwinner,sun6i-a31-r-pinctrl
- - allwinner,sun8i-a33-pinctrl
- - allwinner,sun8i-h3-pinctrl
- - allwinner,sun8i-v3-pinctrl
- - allwinner,sun8i-v3s-pinctrl
- - allwinner,sun9i-a80-r-pinctrl
- - allwinner,sun50i-h6-r-pinctrl
-
- then:
- properties:
- interrupts:
- minItems: 2
- maxItems: 2
-
- else:
- properties:
- interrupts:
- minItems: 1
- maxItems: 1
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun6i-a31-pinctrl
+ - allwinner,sun6i-a31s-pinctrl
+ - allwinner,sun50i-h6-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 4
+ maxItems: 4
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun8i-a23-pinctrl
+ - allwinner,sun8i-a83t-pinctrl
+ - allwinner,sun50i-a64-pinctrl
+ - allwinner,sun50i-h5-pinctrl
+ - allwinner,suniv-f1c100s-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 3
+ maxItems: 3
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun6i-a31-r-pinctrl
+ - allwinner,sun8i-a33-pinctrl
+ - allwinner,sun8i-h3-pinctrl
+ - allwinner,sun8i-v3-pinctrl
+ - allwinner,sun8i-v3s-pinctrl
+ - allwinner,sun9i-a80-r-pinctrl
+ - allwinner,sun50i-h6-r-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun4i-a10-pinctrl
+ - allwinner,sun5i-a10s-pinctrl
+ - allwinner,sun5i-a13-pinctrl
+ - allwinner,sun7i-a20-pinctrl
+ - allwinner,sun8i-a23-r-pinctrl
+ - allwinner,sun8i-a83t-r-pinctrl
+ - allwinner,sun8i-h3-r-pinctrl
+ - allwinner,sun8i-r40-pinctrl
+ - allwinner,sun50i-a64-r-pinctrl
+ - nextthing,gr8-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
additionalProperties: false
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 04/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:02 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:02 UTC (permalink / raw)
To: linus.walleij, robh+dt, mripard, wens
Cc: linux-gpio, devicetree, linux-arm-kernel, linux-kernel,
tiny.windzz, huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Add device tree binding Documentation details for A100 pinctrl driver,
which has a r pin controller and a pin controller with more irq lines.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 35a26abb02e7..34a17d5c6135 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -48,6 +48,8 @@ properties:
- allwinner,sun9i-a80-r-pinctrl
- allwinner,sun50i-a64-pinctrl
- allwinner,sun50i-a64-r-pinctrl
+ - allwinner,sun50i-a100-pinctrl
+ - allwinner,sun50i-a100-r-pinctrl
- allwinner,sun50i-h5-pinctrl
- allwinner,sun50i-h6-pinctrl
- allwinner,sun50i-h6-r-pinctrl
@@ -143,6 +145,18 @@ allOf:
# boards are defining it at the moment so it would generate a lot of
# warnings.
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun50i-a100-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 7
+ maxItems: 7
+
- if:
properties:
compatible:
@@ -216,6 +230,7 @@ allOf:
- allwinner,sun8i-h3-r-pinctrl
- allwinner,sun8i-r40-pinctrl
- allwinner,sun50i-a64-r-pinctrl
+ - allwinner,sun50i-a100-r-pinctrl
- nextthing,gr8-pinctrl
then:
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 04/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
@ 2020-07-24 7:02 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:02 UTC (permalink / raw)
To: linus.walleij, robh+dt, mripard, wens
Cc: devicetree, liyong, tiny.windzz, linux-kernel, linux-gpio,
huangshuosheng, Yangtao Li, Rob Herring, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Add device tree binding Documentation details for A100 pinctrl driver,
which has a r pin controller and a pin controller with more irq lines.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 35a26abb02e7..34a17d5c6135 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -48,6 +48,8 @@ properties:
- allwinner,sun9i-a80-r-pinctrl
- allwinner,sun50i-a64-pinctrl
- allwinner,sun50i-a64-r-pinctrl
+ - allwinner,sun50i-a100-pinctrl
+ - allwinner,sun50i-a100-r-pinctrl
- allwinner,sun50i-h5-pinctrl
- allwinner,sun50i-h6-pinctrl
- allwinner,sun50i-h6-r-pinctrl
@@ -143,6 +145,18 @@ allOf:
# boards are defining it at the moment so it would generate a lot of
# warnings.
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun50i-a100-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 7
+ maxItems: 7
+
- if:
properties:
compatible:
@@ -216,6 +230,7 @@ allOf:
- allwinner,sun8i-h3-r-pinctrl
- allwinner,sun8i-r40-pinctrl
- allwinner,sun50i-a64-r-pinctrl
+ - allwinner,sun50i-a100-r-pinctrl
- nextthing,gr8-pinctrl
then:
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:05 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:05 UTC (permalink / raw)
To: linus.walleij, mripard, wens
Cc: linux-kernel, linux-gpio, linux-arm-kernel, tiny.windzz,
huangshuosheng, liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
This commit introduces support for the pin controller on A100.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 +++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 ++++++++++++++++++
4 files changed, 825 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index f7aae200ee15..593293584ecc 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -94,6 +94,16 @@ config PINCTRL_SUN50I_A64_R
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_A100
+ bool "Support for the Allwinner A100 PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
+config PINCTRL_SUN50I_A100_R
+ bool "Support for the Allwinner A100 R-PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
config PINCTRL_SUN50I_H5
bool "Support for the Allwinner H5 PIO"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index fafcdae8134f..8b7ff0dc3bdf 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,6 +13,8 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN50I_A64) += pinctrl-sun50i-a64.o
obj-$(CONFIG_PINCTRL_SUN50I_A64_R) += pinctrl-sun50i-a64-r.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100) += pinctrl-sun50i-a100.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100_R) += pinctrl-sun50i-a100-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T_R) += pinctrl-sun8i-a83t-r.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
new file mode 100644
index 000000000000..21054fcacd34
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_r_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_pwm"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_cir"), /* IN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),
+};
+
+static const struct sunxi_pinctrl_desc a100_r_pinctrl_data = {
+ .pins = a100_r_pins,
+ .npins = ARRAY_SIZE(a100_r_pins),
+ .pin_base = PL_BASE,
+ .irq_banks = 1,
+};
+
+static int a100_r_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_r_pinctrl_data);
+}
+
+static const struct of_device_id a100_r_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-r-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_r_pinctrl_match);
+
+static struct platform_driver a100_r_pinctrl_driver = {
+ .probe = a100_r_pinctrl_probe,
+ .driver = {
+ .name = "sun50iw10p1-r-pinctrl",
+ .of_match_table = a100_r_pinctrl_match,
+ },
+};
+module_platform_driver(a100_r_pinctrl_driver);
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
new file mode 100644
index 000000000000..19cfd1e76ee2
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
@@ -0,0 +1,708 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* BCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s0"), /* LRCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DIN */
+ SUNXI_FUNCTION(0x3, "i2s0_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s0_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "i2s0_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s0_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* DS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* WP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKM */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKP */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKN */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */
+ SUNXI_FUNCTION(0x4, "uart4"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* DE */
+ SUNXI_FUNCTION(0x4, "uart4"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 19)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "pwm2"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 20)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "pwm3"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 21)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm1"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 22)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm0"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 23)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "pll"), /* LOCK_DBG */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "ledc"), /* LEDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT0 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SM_VS */
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT1 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "tcon0"), /* TRIG */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT2 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT3 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 9)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION(0x3, "i2s1"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* LRCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s1_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s1_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* CLKIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x4, "ledc"),
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x4, "spdif"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* CLK */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "i2s2_din2"), /* DIN2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA2 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "i2s2_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x5, "i2s2_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA3 */
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s2_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "i2s2_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s3_din1"), /* DIN1 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION(0x4, "i2s3_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x3, "i2s3_dout2"), /* DOUT2 */
+ SUNXI_FUNCTION(0x4, "i2s3_din2"), /* DIN2 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* IN */
+ SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */
+ SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */
+ SUNXI_FUNCTION(0x5, "ledc"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)),
+};
+
+static const unsigned int a100_irq_bank_map[] = { 0, 1, 2, 3, 4, 5, 6};
+
+static const struct sunxi_pinctrl_desc a100_pinctrl_data = {
+ .pins = a100_pins,
+ .npins = ARRAY_SIZE(a100_pins),
+ .irq_banks = 7,
+ .irq_bank_map = a100_irq_bank_map,
+ .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
+};
+
+static int a100_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_pinctrl_data);
+}
+
+static const struct of_device_id a100_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_pinctrl_match);
+
+static struct platform_driver a100_pinctrl_driver = {
+ .probe = a100_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-a100-pinctrl",
+ .of_match_table = a100_pinctrl_match,
+ },
+};
+module_platform_driver(a100_pinctrl_driver);
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller
@ 2020-07-24 7:05 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:05 UTC (permalink / raw)
To: linus.walleij, mripard, wens
Cc: liyong, tiny.windzz, linux-kernel, linux-gpio, huangshuosheng,
Yangtao Li, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
This commit introduces support for the pin controller on A100.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c | 105 +++
drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c | 708 ++++++++++++++++++
4 files changed, 825 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index f7aae200ee15..593293584ecc 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -94,6 +94,16 @@ config PINCTRL_SUN50I_A64_R
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_A100
+ bool "Support for the Allwinner A100 PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
+config PINCTRL_SUN50I_A100_R
+ bool "Support for the Allwinner A100 R-PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
config PINCTRL_SUN50I_H5
bool "Support for the Allwinner H5 PIO"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index fafcdae8134f..8b7ff0dc3bdf 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,6 +13,8 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN50I_A64) += pinctrl-sun50i-a64.o
obj-$(CONFIG_PINCTRL_SUN50I_A64_R) += pinctrl-sun50i-a64-r.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100) += pinctrl-sun50i-a100.o
+obj-$(CONFIG_PINCTRL_SUN50I_A100_R) += pinctrl-sun50i-a100-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T_R) += pinctrl-sun8i-a83t-r.o
obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
new file mode 100644
index 000000000000..21054fcacd34
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100-r.c
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_r_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "s_pwm"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_cir"), /* IN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)),
+};
+
+static const struct sunxi_pinctrl_desc a100_r_pinctrl_data = {
+ .pins = a100_r_pins,
+ .npins = ARRAY_SIZE(a100_r_pins),
+ .pin_base = PL_BASE,
+ .irq_banks = 1,
+};
+
+static int a100_r_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_r_pinctrl_data);
+}
+
+static const struct of_device_id a100_r_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-r-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_r_pinctrl_match);
+
+static struct platform_driver a100_r_pinctrl_driver = {
+ .probe = a100_r_pinctrl_probe,
+ .driver = {
+ .name = "sun50iw10p1-r-pinctrl",
+ .of_match_table = a100_r_pinctrl_match,
+ },
+};
+module_platform_driver(a100_r_pinctrl_driver);
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
new file mode 100644
index 000000000000..19cfd1e76ee2
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a100.c
@@ -0,0 +1,708 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ *
+ * Based on:
+ * huangshuosheng <huangshuosheng@allwinnertech.com>
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a100_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2s0"), /* BCLK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s0"), /* LRCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DIN */
+ SUNXI_FUNCTION(0x3, "i2s0_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s0_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "i2s0_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s0_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* DS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* WP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D0N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D1N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2P */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* D2N */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* CKM */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKP */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */
+ SUNXI_FUNCTION(0x3, "lvds0"), /* CKN */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DP3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */
+ SUNXI_FUNCTION(0x4, "dsi0"), /* DM3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */
+ SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */
+ SUNXI_FUNCTION(0x4, "uart4"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* DE */
+ SUNXI_FUNCTION(0x4, "uart4"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 19)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "pwm2"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 20)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "pwm3"),
+ SUNXI_FUNCTION(0x4, "uart4"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 21)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm1"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 22)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "pwm0"),
+ SUNXI_FUNCTION(0x4, "i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 23)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "pll"), /* LOCK_DBG */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "ledc"), /* LEDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT0 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SM_VS */
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT1 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "tcon0"), /* TRIG */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT2 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DOUT0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "bist0"), /* RESULT3 */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* DIN0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 3, 9)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* MS_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI1 */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DI_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* DO_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION(0x4, "jtag_gpu"), /* CK_GPU */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION(0x3, "i2s1"), /* MCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1"), /* LRCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s1_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s1_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x4, "i2s1_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)),
+ /* HOLE */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c1"), /* SDA */
+ SUNXI_FUNCTION(0x3, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* CLKIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* TX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RX */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x4, "ledc"),
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* RTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart3"), /* CTS */
+ SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x4, "spdif"), /* OUT */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXCTL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* CLK */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CS */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "i2s2_din2"), /* DIN2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA0 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* CLK */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA1 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MOSI */
+ SUNXI_FUNCTION(0x4, "i2s2"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* MDIO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA2 */
+ SUNXI_FUNCTION(0x3, "spi2"), /* MISO */
+ SUNXI_FUNCTION(0x4, "i2s2_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x5, "i2s2_din1"), /* DIN1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 11)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "dmic"), /* DATA3 */
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s2_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "i2s2_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 12)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2c3"), /* SCK */
+ SUNXI_FUNCTION(0x4, "i2s3"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* EPHY */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 13)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 14)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "i2s3"), /* LRCK */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 15)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout0"), /* DOUT0 */
+ SUNXI_FUNCTION(0x4, "i2s3_din1"), /* DIN1 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* RXCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 16)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "i2s3_dout1"), /* DOUT1 */
+ SUNXI_FUNCTION(0x4, "i2s3_din0"), /* DIN0 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 17)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* OUT */
+ SUNXI_FUNCTION(0x3, "i2s3_dout2"), /* DOUT2 */
+ SUNXI_FUNCTION(0x4, "i2s3_din2"), /* DIN2 */
+ SUNXI_FUNCTION(0x5, "emac0"), /* TXD2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 18)),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "cir0"), /* IN */
+ SUNXI_FUNCTION(0x3, "i2s3_dout3"), /* DOUT3 */
+ SUNXI_FUNCTION(0x4, "i2s3_din3"), /* DIN3 */
+ SUNXI_FUNCTION(0x5, "ledc"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 19)),
+};
+
+static const unsigned int a100_irq_bank_map[] = { 0, 1, 2, 3, 4, 5, 6};
+
+static const struct sunxi_pinctrl_desc a100_pinctrl_data = {
+ .pins = a100_pins,
+ .npins = ARRAY_SIZE(a100_pins),
+ .irq_banks = 7,
+ .irq_bank_map = a100_irq_bank_map,
+ .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
+};
+
+static int a100_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &a100_pinctrl_data);
+}
+
+static const struct of_device_id a100_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-a100-pinctrl", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a100_pinctrl_match);
+
+static struct platform_driver a100_pinctrl_driver = {
+ .probe = a100_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-a100-pinctrl",
+ .of_match_table = a100_pinctrl_match,
+ },
+};
+module_platform_driver(a100_pinctrl_driver);
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:09 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:09 UTC (permalink / raw)
To: srinivas.kandagatla, robh+dt, mripard, wens
Cc: devicetree, linux-arm-kernel, linux-kernel, tiny.windzz,
huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's SID controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../nvmem/allwinner,sun4i-a10-sid.yaml | 19 +++++++++++--------
1 file changed, 11 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
index daf1321d76ad..6687ab720304 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
@@ -15,14 +15,17 @@ allOf:
properties:
compatible:
- enum:
- - allwinner,sun4i-a10-sid
- - allwinner,sun7i-a20-sid
- - allwinner,sun8i-a83t-sid
- - allwinner,sun8i-h3-sid
- - allwinner,sun50i-a64-sid
- - allwinner,sun50i-h5-sid
- - allwinner,sun50i-h6-sid
+ oneOf:
+ - const: allwinner,sun4i-a10-sid
+ - const: allwinner,sun7i-a20-sid
+ - const: allwinner,sun8i-a83t-sid
+ - const: allwinner,sun8i-h3-sid
+ - const: allwinner,sun50i-a64-sid
+ - items:
+ - const: allwinner,sun50i-a100-sid
+ - const: allwinner,sun50i-a64-sid
+ - const: allwinner,sun50i-h5-sid
+ - const: allwinner,sun50i-h6-sid
reg:
maxItems: 1
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller
@ 2020-07-24 7:09 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:09 UTC (permalink / raw)
To: srinivas.kandagatla, robh+dt, mripard, wens
Cc: devicetree, liyong, tiny.windzz, linux-kernel, huangshuosheng,
Yangtao Li, Rob Herring, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's SID controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../nvmem/allwinner,sun4i-a10-sid.yaml | 19 +++++++++++--------
1 file changed, 11 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
index daf1321d76ad..6687ab720304 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
@@ -15,14 +15,17 @@ allOf:
properties:
compatible:
- enum:
- - allwinner,sun4i-a10-sid
- - allwinner,sun7i-a20-sid
- - allwinner,sun8i-a83t-sid
- - allwinner,sun8i-h3-sid
- - allwinner,sun50i-a64-sid
- - allwinner,sun50i-h5-sid
- - allwinner,sun50i-h6-sid
+ oneOf:
+ - const: allwinner,sun4i-a10-sid
+ - const: allwinner,sun7i-a20-sid
+ - const: allwinner,sun8i-a83t-sid
+ - const: allwinner,sun8i-h3-sid
+ - const: allwinner,sun50i-a64-sid
+ - items:
+ - const: allwinner,sun50i-a100-sid
+ - const: allwinner,sun50i-a64-sid
+ - const: allwinner,sun50i-h5-sid
+ - const: allwinner,sun50i-h6-sid
reg:
maxItems: 1
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:10 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:10 UTC (permalink / raw)
To: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, mripard, wens, linux-pm
Cc: devicetree, linux-arm-kernel, linux-kernel, huangshuosheng,
liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's ths controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
index 87369264feb9..9d40fc7ff6fd 100644
--- a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
+++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
@@ -17,6 +17,7 @@ properties:
- allwinner,sun8i-h3-ths
- allwinner,sun8i-r40-ths
- allwinner,sun50i-a64-ths
+ - allwinner,sun50i-a100-ths
- allwinner,sun50i-h5-ths
- allwinner,sun50i-h6-ths
@@ -61,7 +62,9 @@ allOf:
properties:
compatible:
contains:
- const: allwinner,sun50i-h6-ths
+ enum:
+ - allwinner,sun50i-a100-ths
+ - allwinner,sun50i-h6-ths
then:
properties:
@@ -103,6 +106,7 @@ allOf:
- const: allwinner,sun8i-h3-ths
- const: allwinner,sun8i-r40-ths
- const: allwinner,sun50i-a64-ths
+ - const: allwinner,sun50i-a100-ths
- const: allwinner,sun50i-h5-ths
- const: allwinner,sun50i-h6-ths
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
@ 2020-07-24 7:10 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:10 UTC (permalink / raw)
To: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, mripard, wens, linux-pm
Cc: devicetree, liyong, linux-kernel, huangshuosheng, Yangtao Li,
Rob Herring, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's ths controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/thermal/allwinner,sun8i-a83t-ths.yaml | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
index 87369264feb9..9d40fc7ff6fd 100644
--- a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
+++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
@@ -17,6 +17,7 @@ properties:
- allwinner,sun8i-h3-ths
- allwinner,sun8i-r40-ths
- allwinner,sun50i-a64-ths
+ - allwinner,sun50i-a100-ths
- allwinner,sun50i-h5-ths
- allwinner,sun50i-h6-ths
@@ -61,7 +62,9 @@ allOf:
properties:
compatible:
contains:
- const: allwinner,sun50i-h6-ths
+ enum:
+ - allwinner,sun50i-a100-ths
+ - allwinner,sun50i-h6-ths
then:
properties:
@@ -103,6 +106,7 @@ allOf:
- const: allwinner,sun8i-h3-ths
- const: allwinner,sun8i-r40-ths
- const: allwinner,sun50i-a64-ths
+ - const: allwinner,sun50i-a100-ths
- const: allwinner,sun50i-h5-ths
- const: allwinner,sun50i-h6-ths
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:11 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:11 UTC (permalink / raw)
To: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, mripard, wens, linux-pm
Cc: devicetree, linux-arm-kernel, linux-kernel, huangshuosheng,
liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/thermal/sun8i_thermal.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 74d73be16496..f423d44b9290 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -244,7 +244,7 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
ft_temp = (caldata[0] & FT_TEMP_MASK) * 100;
for (i = 0; i < tmdev->chip->sensor_num; i++) {
- int sensor_reg = caldata[i + 1];
+ int sensor_reg = caldata[i + 1] & TEMP_CALIB_MASK;
int cdata, offset;
int sensor_temp = tmdev->chip->calc_temp(tmdev, i, sensor_reg);
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
@ 2020-07-24 7:11 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:11 UTC (permalink / raw)
To: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, mripard, wens, linux-pm
Cc: devicetree, liyong, linux-kernel, huangshuosheng, Yangtao Li,
linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/thermal/sun8i_thermal.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 74d73be16496..f423d44b9290 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -244,7 +244,7 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
ft_temp = (caldata[0] & FT_TEMP_MASK) * 100;
for (i = 0; i < tmdev->chip->sensor_num; i++) {
- int sensor_reg = caldata[i + 1];
+ int sensor_reg = caldata[i + 1] & TEMP_CALIB_MASK;
int cdata, offset;
int sensor_temp = tmdev->chip->calc_temp(tmdev, i, sensor_reg);
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 09/16] thermal: sun8i: Add A100's THS controller support
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:11 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:11 UTC (permalink / raw)
To: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, mripard, wens, linux-pm
Cc: devicetree, linux-arm-kernel, linux-kernel, huangshuosheng,
liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
This patch add thermal sensor controller support for A100,
which is similar to the previous ones.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/thermal/sun8i_thermal.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index f423d44b9290..f8b13071a6f4 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -590,6 +590,19 @@ static const struct ths_thermal_chip sun50i_a64_ths = {
.calc_temp = sun8i_ths_calc_temp,
};
+static const struct ths_thermal_chip sun50i_a100_ths = {
+ .sensor_num = 3,
+ .has_bus_clk_reset = true,
+ .ft_deviation = 8000,
+ .offset = 187744,
+ .scale = 672,
+ .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+ .calibrate = sun50i_h6_ths_calibrate,
+ .init = sun50i_h6_thermal_init,
+ .irq_ack = sun50i_h6_irq_ack,
+ .calc_temp = sun8i_ths_calc_temp,
+};
+
static const struct ths_thermal_chip sun50i_h5_ths = {
.sensor_num = 2,
.has_mod_clk = true,
@@ -619,6 +632,7 @@ static const struct of_device_id of_ths_match[] = {
{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
{ .compatible = "allwinner,sun8i-r40-ths", .data = &sun8i_r40_ths },
{ .compatible = "allwinner,sun50i-a64-ths", .data = &sun50i_a64_ths },
+ { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths },
{ .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
{ /* sentinel */ },
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 09/16] thermal: sun8i: Add A100's THS controller support
@ 2020-07-24 7:11 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:11 UTC (permalink / raw)
To: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, mripard, wens, linux-pm
Cc: devicetree, liyong, linux-kernel, huangshuosheng, Yangtao Li,
linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
This patch add thermal sensor controller support for A100,
which is similar to the previous ones.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
drivers/thermal/sun8i_thermal.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index f423d44b9290..f8b13071a6f4 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -590,6 +590,19 @@ static const struct ths_thermal_chip sun50i_a64_ths = {
.calc_temp = sun8i_ths_calc_temp,
};
+static const struct ths_thermal_chip sun50i_a100_ths = {
+ .sensor_num = 3,
+ .has_bus_clk_reset = true,
+ .ft_deviation = 8000,
+ .offset = 187744,
+ .scale = 672,
+ .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+ .calibrate = sun50i_h6_ths_calibrate,
+ .init = sun50i_h6_thermal_init,
+ .irq_ack = sun50i_h6_irq_ack,
+ .calc_temp = sun8i_ths_calc_temp,
+};
+
static const struct ths_thermal_chip sun50i_h5_ths = {
.sensor_num = 2,
.has_mod_clk = true,
@@ -619,6 +632,7 @@ static const struct of_device_id of_ths_match[] = {
{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
{ .compatible = "allwinner,sun8i-r40-ths", .data = &sun8i_r40_ths },
{ .compatible = "allwinner,sun50i-a64-ths", .data = &sun50i_a64_ths },
+ { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths },
{ .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
{ /* sentinel */ },
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C
2020-07-24 6:52 ` Frank Lee
` (9 preceding siblings ...)
(?)
@ 2020-07-24 7:13 ` Frank Lee
2020-07-27 15:36 ` Lee Jones
-1 siblings, 1 reply; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:13 UTC (permalink / raw)
To: lee.jones, wens, linux-kernel
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
The AXP803 can be used both using the RSB proprietary bus, or a more
traditional I2C bus.
Let's add that possibility.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
---
drivers/mfd/axp20x-i2c.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
index 14f9df74f855..446a7d0bbb47 100644
--- a/drivers/mfd/axp20x-i2c.c
+++ b/drivers/mfd/axp20x-i2c.c
@@ -63,6 +63,7 @@ static const struct of_device_id axp20x_i2c_of_match[] = {
{ .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
{ .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
{ },
};
@@ -74,6 +75,7 @@ static const struct i2c_device_id axp20x_i2c_id[] = {
{ "axp209", 0 },
{ "axp221", 0 },
{ "axp223", 0 },
+ { "axp803", 0 },
{ "axp806", 0 },
{ },
};
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 11/16] dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:14 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:14 UTC (permalink / raw)
To: tglx, jason, maz, robh+dt, mripard, wens, linux-kernel,
devicetree, linux-arm-kernel
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
There is no one use "allwinner,sun9i-a80-sc-nmi". The A80 uses
"allwinner,sun9i-a80-nmi".
Let's fix it.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
index 7cd6b8bacfa0..d8fe2d9a307b 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
@@ -29,7 +29,7 @@ properties:
- items:
- const: allwinner,sun8i-a83t-r-intc
- const: allwinner,sun6i-a31-r-intc
- - const: allwinner,sun9i-a80-sc-nmi
+ - const: allwinner,sun9i-a80-nmi
- items:
- const: allwinner,sun50i-a64-r-intc
- const: allwinner,sun6i-a31-r-intc
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 11/16] dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
@ 2020-07-24 7:14 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:14 UTC (permalink / raw)
To: tglx, jason, maz, robh+dt, mripard, wens, linux-kernel,
devicetree, linux-arm-kernel
Cc: tiny.windzz, liyong, huangshuosheng, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
There is no one use "allwinner,sun9i-a80-sc-nmi". The A80 uses
"allwinner,sun9i-a80-nmi".
Let's fix it.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
index 7cd6b8bacfa0..d8fe2d9a307b 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
@@ -29,7 +29,7 @@ properties:
- items:
- const: allwinner,sun8i-a83t-r-intc
- const: allwinner,sun6i-a31-r-intc
- - const: allwinner,sun9i-a80-sc-nmi
+ - const: allwinner,sun9i-a80-nmi
- items:
- const: allwinner,sun50i-a64-r-intc
- const: allwinner,sun6i-a31-r-intc
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 12/16] dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:15 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:15 UTC (permalink / raw)
To: tglx, jason, maz, robh+dt, mripard, wens, linux-kernel,
devicetree, linux-arm-kernel
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's nmi controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
index d8fe2d9a307b..8acca0ae3129 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
@@ -33,6 +33,9 @@ properties:
- items:
- const: allwinner,sun50i-a64-r-intc
- const: allwinner,sun6i-a31-r-intc
+ - items:
+ - const: allwinner,sun50i-a100-nmi
+ - const: allwinner,sun9i-a80-nmi
- items:
- const: allwinner,sun50i-h6-r-intc
- const: allwinner,sun6i-a31-r-intc
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 12/16] dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
@ 2020-07-24 7:15 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:15 UTC (permalink / raw)
To: tglx, jason, maz, robh+dt, mripard, wens, linux-kernel,
devicetree, linux-arm-kernel
Cc: tiny.windzz, liyong, huangshuosheng, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's nmi controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
index d8fe2d9a307b..8acca0ae3129 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
@@ -33,6 +33,9 @@ properties:
- items:
- const: allwinner,sun50i-a64-r-intc
- const: allwinner,sun6i-a31-r-intc
+ - items:
+ - const: allwinner,sun50i-a100-nmi
+ - const: allwinner,sun9i-a80-nmi
- items:
- const: allwinner,sun50i-h6-r-intc
- const: allwinner,sun6i-a31-r-intc
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 13/16] dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
2020-07-24 6:52 ` Frank Lee
` (12 preceding siblings ...)
(?)
@ 2020-07-24 7:17 ` Frank Lee
2020-08-25 8:02 ` Wolfram Sang
-1 siblings, 1 reply; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:17 UTC (permalink / raw)
To: gregory.clement, robh+dt, linux-i2c, devicetree, linux-kernel
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Allwinner A100 have a mv64xxx i2c interface available to be used.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
index 2ceb05ba2df5..5b5ae402f97a 100644
--- a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
@@ -26,6 +26,9 @@ properties:
- items:
- const: allwinner,sun50i-a64-i2c
- const: allwinner,sun6i-a31-i2c
+ - items:
+ - const: allwinner,sun50i-a100-i2c
+ - const: allwinner,sun6i-a31-i2c
- items:
- const: allwinner,sun50i-h6-i2c
- const: allwinner,sun6i-a31-i2c
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:18 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:18 UTC (permalink / raw)
To: robh+dt, mripard, wens
Cc: devicetree, linux-arm-kernel, linux-kernel, tiny.windzz,
huangshuosheng, liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
Allwinner A100 is a new SoC with Cortex-A53 cores, this commit adds
the basical DTSI file of it, including the clock, i2c, pins, sid, ths,
nmi, and UART support.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
.../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 364 ++++++++++++++++++
1 file changed, 364 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
new file mode 100644
index 000000000000..cc321c04f121
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ dcxo24M: dcxo24M-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "dcxo24M";
+ #clock-cells = <0>;
+ };
+
+ iosc: internal-osc-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <16000000>;
+ clock-accuracy = <300000000>;
+ clock-output-names = "iosc";
+ #clock-cells = <0>;
+ };
+
+ osc32k: osc32k-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ #clock-cells = <0>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0x3fffffff>;
+
+ ccu: clock@3001000 {
+ compatible = "allwinner,sun50i-a100-ccu";
+ reg = <0x03001000 0x1000>;
+ clocks = <&dcxo24M>, <&osc32k>, <&iosc>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ gic: interrupt-controller@3021000 {
+ compatible = "arm,gic-400";
+ reg = <0x03021000 0x1000>, <0x03022000 0x2000>,
+ <0x03024000 0x2000>, <0x03026000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ efuse@3006000 {
+ compatible = "allwinner,sun50i-a100-sid",
+ "allwinner,sun50i-a64-sid";
+ reg = <0x03006000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ths_calibration: calib@14 {
+ reg = <0x14 8>;
+ };
+ };
+
+ pio: pinctrl@300b000 {
+ compatible = "allwinner,sun50i-a100-pinctrl";
+ reg = <0x0300b000 0x400>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB1>, <&dcxo24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB9", "PB10";
+ function = "uart0";
+ };
+ };
+
+ uart0: serial@5000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@5000400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@5000800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@5000c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@5001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05001000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@5002000 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@5002400 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@5002800 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002800 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@5002c00 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002c00 0x400>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ths: thermal-sensor@5070400 {
+ compatible = "allwinner,sun50i-a100-ths";
+ reg = <0x05070400 0x100>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_THS>;
+ clock-names = "bus";
+ resets = <&ccu RST_BUS_THS>;
+ nvmem-cells = <&ths_calibration>;
+ nvmem-cell-names = "calibration";
+ #thermal-sensor-cells = <1>;
+ };
+
+ r_ccu: clock@7010000 {
+ compatible = "allwinner,sun50i-a100-r-ccu";
+ reg = <0x07010000 0x300>;
+ clocks = <&dcxo24M>, <&osc32k>, <&iosc>,
+ <&ccu CLK_PLL_PERIPH0>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ r_intc: interrupt-controller@7010320 {
+ compatible = "allwinner,sun50i-a100-nmi",
+ "allwinner,sun9i-a80-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x07010320 0xc>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ r_pio: pinctrl@7022000 {
+ compatible = "allwinner,sun50i-a100-r-pinctrl";
+ reg = <0x07022000 0x400>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1>, <&dcxo24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ r_i2c0_pins: r-i2c0-pins {
+ pins = "PL0", "PL1";
+ function = "s_i2c0";
+ };
+
+ r_i2c1_pins: r-i2c1-pins {
+ pins = "PL8", "PL9";
+ function = "s_i2c1";
+ };
+ };
+
+ r_uart: serial@7080000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07080000 0x400>;
+ interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&r_ccu CLK_R_APB2_UART>;
+ resets = <&r_ccu RST_R_APB2_UART>;
+ status = "disabled";
+ };
+
+ r_i2c0: i2c@7081400 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x07081400 0x400>;
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB2_I2C0>;
+ resets = <&r_ccu RST_R_APB2_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ r_i2c1: i2c@7081800 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x07081800 0x400>;
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB2_I2C1>;
+ resets = <&r_ccu RST_R_APB2_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ thermal-zones {
+ cpu-thermal-zone {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 0>;
+ };
+
+ ddr-thermal-zone {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 2>;
+ };
+
+ gpu-thermal-zone {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 1>;
+ };
+ };
+};
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
@ 2020-07-24 7:18 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:18 UTC (permalink / raw)
To: robh+dt, mripard, wens
Cc: devicetree, liyong, tiny.windzz, linux-kernel, huangshuosheng,
Yangtao Li, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Allwinner A100 is a new SoC with Cortex-A53 cores, this commit adds
the basical DTSI file of it, including the clock, i2c, pins, sid, ths,
nmi, and UART support.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
.../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 364 ++++++++++++++++++
1 file changed, 364 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
new file mode 100644
index 000000000000..cc321c04f121
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-a100-ccu.h>
+#include <dt-bindings/clock/sun50i-a100-r-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-ccu.h>
+#include <dt-bindings/reset/sun50i-a100-r-ccu.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x0>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x1>;
+ enable-method = "psci";
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x2>;
+ enable-method = "psci";
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ dcxo24M: dcxo24M-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "dcxo24M";
+ #clock-cells = <0>;
+ };
+
+ iosc: internal-osc-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <16000000>;
+ clock-accuracy = <300000000>;
+ clock-output-names = "iosc";
+ #clock-cells = <0>;
+ };
+
+ osc32k: osc32k-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ #clock-cells = <0>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0x3fffffff>;
+
+ ccu: clock@3001000 {
+ compatible = "allwinner,sun50i-a100-ccu";
+ reg = <0x03001000 0x1000>;
+ clocks = <&dcxo24M>, <&osc32k>, <&iosc>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ gic: interrupt-controller@3021000 {
+ compatible = "arm,gic-400";
+ reg = <0x03021000 0x1000>, <0x03022000 0x2000>,
+ <0x03024000 0x2000>, <0x03026000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ efuse@3006000 {
+ compatible = "allwinner,sun50i-a100-sid",
+ "allwinner,sun50i-a64-sid";
+ reg = <0x03006000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ths_calibration: calib@14 {
+ reg = <0x14 8>;
+ };
+ };
+
+ pio: pinctrl@300b000 {
+ compatible = "allwinner,sun50i-a100-pinctrl";
+ reg = <0x0300b000 0x400>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB1>, <&dcxo24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB9", "PB10";
+ function = "uart0";
+ };
+ };
+
+ uart0: serial@5000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@5000400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@5000800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@5000c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@5001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05001000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@5002000 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@5002400 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@5002800 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002800 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@5002c00 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002c00 0x400>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ths: thermal-sensor@5070400 {
+ compatible = "allwinner,sun50i-a100-ths";
+ reg = <0x05070400 0x100>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_THS>;
+ clock-names = "bus";
+ resets = <&ccu RST_BUS_THS>;
+ nvmem-cells = <&ths_calibration>;
+ nvmem-cell-names = "calibration";
+ #thermal-sensor-cells = <1>;
+ };
+
+ r_ccu: clock@7010000 {
+ compatible = "allwinner,sun50i-a100-r-ccu";
+ reg = <0x07010000 0x300>;
+ clocks = <&dcxo24M>, <&osc32k>, <&iosc>,
+ <&ccu CLK_PLL_PERIPH0>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ r_intc: interrupt-controller@7010320 {
+ compatible = "allwinner,sun50i-a100-nmi",
+ "allwinner,sun9i-a80-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x07010320 0xc>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ r_pio: pinctrl@7022000 {
+ compatible = "allwinner,sun50i-a100-r-pinctrl";
+ reg = <0x07022000 0x400>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1>, <&dcxo24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ r_i2c0_pins: r-i2c0-pins {
+ pins = "PL0", "PL1";
+ function = "s_i2c0";
+ };
+
+ r_i2c1_pins: r-i2c1-pins {
+ pins = "PL8", "PL9";
+ function = "s_i2c1";
+ };
+ };
+
+ r_uart: serial@7080000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x07080000 0x400>;
+ interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&r_ccu CLK_R_APB2_UART>;
+ resets = <&r_ccu RST_R_APB2_UART>;
+ status = "disabled";
+ };
+
+ r_i2c0: i2c@7081400 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x07081400 0x400>;
+ interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB2_I2C0>;
+ resets = <&r_ccu RST_R_APB2_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ r_i2c1: i2c@7081800 {
+ compatible = "allwinner,sun50i-a100-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x07081800 0x400>;
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB2_I2C1>;
+ resets = <&r_ccu RST_R_APB2_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ thermal-zones {
+ cpu-thermal-zone {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 0>;
+ };
+
+ ddr-thermal-zone {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 2>;
+ };
+
+ gpu-thermal-zone {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&ths 1>;
+ };
+ };
+};
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 15/16] dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:20 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:20 UTC (permalink / raw)
To: robh+dt, mripard, wens, icenowy, megous, clabbe, karlp, bage,
devicetree, linux-arm-kernel, linux-kernel
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Document board compatible names for Allwinner A100 Perf1 Board.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 87817ff0cd35..dbec66c1377a 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -16,6 +16,11 @@ properties:
compatible:
oneOf:
+ - description: Allwinner A100 Perf1 Board
+ items:
+ - const: allwinner,a100-perf1
+ - const: allwinner,sun50i-a100
+
- description: Allwinner A23 Evaluation Board
items:
- const: allwinner,sun8i-a23-evb
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 15/16] dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
@ 2020-07-24 7:20 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:20 UTC (permalink / raw)
To: robh+dt, mripard, wens, icenowy, megous, clabbe, karlp, bage,
devicetree, linux-arm-kernel, linux-kernel
Cc: tiny.windzz, liyong, huangshuosheng, Yangtao Li, Rob Herring
From: Yangtao Li <frank@allwinnertech.com>
Document board compatible names for Allwinner A100 Perf1 Board.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 87817ff0cd35..dbec66c1377a 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -16,6 +16,11 @@ properties:
compatible:
oneOf:
+ - description: Allwinner A100 Perf1 Board
+ items:
+ - const: allwinner,a100-perf1
+ - const: allwinner,sun50i-a100
+
- description: Allwinner A23 Evaluation Board
items:
- const: allwinner,sun8i-a23-evb
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 16/16] arm64: allwinner: A100: add support for Allwinner Perf1 board
2020-07-24 6:52 ` Frank Lee
@ 2020-07-24 7:21 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:21 UTC (permalink / raw)
To: mripard, wens, robh+dt, linux-arm-kernel, devicetree, linux-kernel
Cc: tiny.windzz, huangshuosheng, liyong, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
A100 perf1 is an Allwinner A100-based SBC, with the following features:
- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- on-board Nand flash
- ···
Adds initial support for it, including UART and PMU.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-a100-allwinner-perf1.dts | 180 ++++++++++++++++++
2 files changed, 181 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index e4d3cd0ac5bb..ab780dbdd17b 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -14,6 +14,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-emlid-neutis-n5-devboard.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
new file mode 100644
index 000000000000..d34c2bb1079f
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-a100.dtsi"
+
+/{
+ model = "Allwinner A100 Perf1";
+ compatible = "allwinner,a100-perf1", "allwinner,sun50i-a100";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&pio {
+ vcc-pb-supply = <®_dcdc1>;
+ vcc-pc-supply = <®_eldo1>;
+ vcc-pd-supply = <®_dcdc1>;
+ vcc-pe-supply = <®_dldo2>;
+ vcc-pf-supply = <®_dcdc1>;
+ vcc-pg-supply = <®_dldo1>;
+ vcc-ph-supply = <®_dcdc1>;
+};
+
+&r_pio {
+ /*
+ * FIXME: We can't add that supply for now since it would
+ * create a circular dependency between pinctrl, the regulator
+ * and the RSB Bus.
+ *
+ * vcc-pl-supply = <®_aldo3>;
+ */
+};
+
+&r_i2c0 {
+ status = "okay";
+
+ axp803: pmic@34 {
+ compatible = "x-powers,axp803";
+ reg = <0x34>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+ };
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dram-1";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-pl";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-io-usb-pd-emmc-nand-card";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ /*
+ * FIXME: update min and max before support dvfs.
+ */
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+ regulator-name = "vdd-sys-usb-dram";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram-2";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pg-dcxo-wifi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-pe-csi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ldo-avdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avcc-csi";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pc-lvds-csi-efuse-emmc-nand";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-mipi-lcd";
+};
+
+®_fldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-cpus-usb";
+};
+
+®_ldo_io0 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ctp";
+ status = "okay";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
--
2.24.0
^ permalink raw reply related [flat|nested] 84+ messages in thread
* [PATCH v5 16/16] arm64: allwinner: A100: add support for Allwinner Perf1 board
@ 2020-07-24 7:21 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-24 7:21 UTC (permalink / raw)
To: mripard, wens, robh+dt, linux-arm-kernel, devicetree, linux-kernel
Cc: tiny.windzz, liyong, huangshuosheng, Yangtao Li
From: Yangtao Li <frank@allwinnertech.com>
A100 perf1 is an Allwinner A100-based SBC, with the following features:
- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- on-board Nand flash
- ···
Adds initial support for it, including UART and PMU.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-a100-allwinner-perf1.dts | 180 ++++++++++++++++++
2 files changed, 181 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index e4d3cd0ac5bb..ab780dbdd17b 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -14,6 +14,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-emlid-neutis-n5-devboard.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
new file mode 100644
index 000000000000..d34c2bb1079f
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100-allwinner-perf1.dts
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (c) 2020 Yangtao Li <frank@allwinnertech.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-a100.dtsi"
+
+/{
+ model = "Allwinner A100 Perf1";
+ compatible = "allwinner,a100-perf1", "allwinner,sun50i-a100";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&pio {
+ vcc-pb-supply = <®_dcdc1>;
+ vcc-pc-supply = <®_eldo1>;
+ vcc-pd-supply = <®_dcdc1>;
+ vcc-pe-supply = <®_dldo2>;
+ vcc-pf-supply = <®_dcdc1>;
+ vcc-pg-supply = <®_dldo1>;
+ vcc-ph-supply = <®_dcdc1>;
+};
+
+&r_pio {
+ /*
+ * FIXME: We can't add that supply for now since it would
+ * create a circular dependency between pinctrl, the regulator
+ * and the RSB Bus.
+ *
+ * vcc-pl-supply = <®_aldo3>;
+ */
+};
+
+&r_i2c0 {
+ status = "okay";
+
+ axp803: pmic@34 {
+ compatible = "x-powers,axp803";
+ reg = <0x34>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+ };
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dram-1";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-pl";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-io-usb-pd-emmc-nand-card";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ /*
+ * FIXME: update min and max before support dvfs.
+ */
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+ regulator-name = "vdd-sys-usb-dram";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram-2";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pg-dcxo-wifi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-pe-csi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ldo-avdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avcc-csi";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pc-lvds-csi-efuse-emmc-nand";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-mipi-lcd";
+};
+
+®_fldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd-cpus-usb";
+};
+
+®_ldo_io0 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ctp";
+ status = "okay";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
--
2.24.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 84+ messages in thread
* Re: [PATCH v5 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C
2020-07-24 7:13 ` [PATCH v5 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
@ 2020-07-27 15:36 ` Lee Jones
0 siblings, 0 replies; 84+ messages in thread
From: Lee Jones @ 2020-07-27 15:36 UTC (permalink / raw)
To: Frank Lee; +Cc: wens, linux-kernel, tiny.windzz, huangshuosheng, liyong
On Fri, 24 Jul 2020, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> The AXP803 can be used both using the RSB proprietary bus, or a more
> traditional I2C bus.
>
> Let's add that possibility.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Chen-Yu Tsai <wens@csie.org>
> ---
> drivers/mfd/axp20x-i2c.c | 2 ++
> 1 file changed, 2 insertions(+)
Why do you keep sending this?
It was applied in v3 [0].
[0] https://lkml.org/lkml/2020/7/16/745
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
2020-07-24 6:58 ` Frank Lee
@ 2020-07-27 19:57 ` Rob Herring
-1 siblings, 0 replies; 84+ messages in thread
From: Rob Herring @ 2020-07-27 19:57 UTC (permalink / raw)
To: Frank Lee
Cc: linux-arm-kernel, sboyd, mturquette, robh+dt, wens, liyong,
mripard, linux-kernel, devicetree, p.zabel, linux-clk,
huangshuosheng, tiny.windzz
On Fri, 24 Jul 2020 14:58:43 +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add support for a100 in the sunxi-ng CCU framework.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> ---
> drivers/clk/sunxi-ng/Kconfig | 10 +
> drivers/clk/sunxi-ng/Makefile | 2 +
> drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++
> drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
> drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++
> drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
> include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
> include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
> include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
> include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
> 10 files changed, 1804 insertions(+)
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
> create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
> create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
> create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
> create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
@ 2020-07-27 19:57 ` Rob Herring
0 siblings, 0 replies; 84+ messages in thread
From: Rob Herring @ 2020-07-27 19:57 UTC (permalink / raw)
To: Frank Lee
Cc: liyong, devicetree, sboyd, mturquette, linux-kernel, mripard,
tiny.windzz, wens, robh+dt, huangshuosheng, p.zabel, linux-clk,
linux-arm-kernel
On Fri, 24 Jul 2020 14:58:43 +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add support for a100 in the sunxi-ng CCU framework.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> ---
> drivers/clk/sunxi-ng/Kconfig | 10 +
> drivers/clk/sunxi-ng/Makefile | 2 +
> drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c | 214 +++
> drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h | 21 +
> drivers/clk/sunxi-ng/ccu-sun50i-a100.c | 1276 +++++++++++++++++
> drivers/clk/sunxi-ng/ccu-sun50i-a100.h | 56 +
> include/dt-bindings/clock/sun50i-a100-ccu.h | 116 ++
> include/dt-bindings/clock/sun50i-a100-r-ccu.h | 23 +
> include/dt-bindings/reset/sun50i-a100-ccu.h | 68 +
> include/dt-bindings/reset/sun50i-a100-r-ccu.h | 18 +
> 10 files changed, 1804 insertions(+)
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100-r.h
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-a100.h
> create mode 100644 include/dt-bindings/clock/sun50i-a100-ccu.h
> create mode 100644 include/dt-bindings/clock/sun50i-a100-r-ccu.h
> create mode 100644 include/dt-bindings/reset/sun50i-a100-ccu.h
> create mode 100644 include/dt-bindings/reset/sun50i-a100-r-ccu.h
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-07-24 6:52 ` Frank Lee
@ 2020-07-30 1:20 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-30 1:20 UTC (permalink / raw)
To: Frank Lee
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Michael Turquette,
Stephen Boyd, gregory.clement, Thomas Gleixner, jason,
Marc Zyngier, Srini Kandagatla, Linus Walleij, Vasily Khoruzhick,
Zhang Rui, Daniel Lezcano, Amit Kucheria, Lee Jones, p.zabel,
Icenowy Zheng, Ondřej Jirman, clabbe, bage, devicetree,
Linux ARM, Linux Kernel Mailing List, linux-clk, linux-i2c,
linux-gpio, Linux PM
HI Maxime,
Any comments on thermal and other patches?
I hope these patches can be integrated into the mainline as soon as possible.
Thx,
Yangtao
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-07-30 1:20 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-07-30 1:20 UTC (permalink / raw)
To: Frank Lee
Cc: Ondřej Jirman, Linus Walleij, Srini Kandagatla, linux-i2c,
Lee Jones, linux-clk, Amit Kucheria, Marc Zyngier,
gregory.clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
clabbe, Zhang Rui, Michael Turquette, Icenowy Zheng, devicetree,
jason, bage, Linux PM, Maxime Ripard, linux-gpio, Rob Herring,
Thomas Gleixner, Linux ARM, Stephen Boyd,
Linux Kernel Mailing List, p.zabel
HI Maxime,
Any comments on thermal and other patches?
I hope these patches can be integrated into the mainline as soon as possible.
Thx,
Yangtao
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-07-30 1:20 ` Frank Lee
@ 2020-08-24 7:44 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-08-24 7:44 UTC (permalink / raw)
To: Frank Lee
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Michael Turquette,
Stephen Boyd, gregory.clement, Thomas Gleixner, jason,
Marc Zyngier, Srini Kandagatla, Linus Walleij, Vasily Khoruzhick,
Zhang Rui, Daniel Lezcano, Amit Kucheria, Lee Jones, p.zabel,
Icenowy Zheng, Ondřej Jirman, clabbe, bage, devicetree,
Linux ARM, Linux Kernel Mailing List, linux-clk, linux-i2c,
linux-gpio, Linux PM
ping......
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-24 7:44 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-08-24 7:44 UTC (permalink / raw)
To: Frank Lee
Cc: Ondřej Jirman, Linus Walleij, Srini Kandagatla, linux-i2c,
Lee Jones, linux-clk, Amit Kucheria, Marc Zyngier,
gregory.clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
clabbe, Zhang Rui, Michael Turquette, Icenowy Zheng, devicetree,
jason, bage, Linux PM, Maxime Ripard, linux-gpio, Rob Herring,
Thomas Gleixner, Linux ARM, Stephen Boyd,
Linux Kernel Mailing List, p.zabel
ping......
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-08-24 7:44 ` Frank Lee
@ 2020-08-24 8:03 ` Lee Jones
-1 siblings, 0 replies; 84+ messages in thread
From: Lee Jones @ 2020-08-24 8:03 UTC (permalink / raw)
To: Frank Lee
Cc: Frank Lee, Rob Herring, Maxime Ripard, Chen-Yu Tsai,
Michael Turquette, Stephen Boyd, gregory.clement,
Thomas Gleixner, jason, Marc Zyngier, Srini Kandagatla,
Linus Walleij, Vasily Khoruzhick, Zhang Rui, Daniel Lezcano,
Amit Kucheria, p.zabel, Icenowy Zheng, Ondřej Jirman,
clabbe, bage, devicetree, Linux ARM, Linux Kernel Mailing List,
linux-clk, linux-i2c, linux-gpio, Linux PM
On Mon, 24 Aug 2020, Frank Lee wrote:
> ping......
"Please don't send content free pings and please allow a reasonable
time for review. People get busy, go on holiday, attend conferences
and so on so unless there is some reason for urgency (like critical
bug fixes) please allow at least a couple of weeks for review. If
there have been review comments then people may be waiting for those
to be addressed. Sending content free pings just adds to the mail
volume (if they are seen at all) and if something has gone wrong
you'll have to resend the patches anyway so [RESEND]ing with any
comments addressed is generally a much better approach."
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-24 8:03 ` Lee Jones
0 siblings, 0 replies; 84+ messages in thread
From: Lee Jones @ 2020-08-24 8:03 UTC (permalink / raw)
To: Frank Lee
Cc: Ondřej Jirman, Linus Walleij, Srini Kandagatla, linux-i2c,
Frank Lee, linux-clk, Amit Kucheria, Marc Zyngier,
gregory.clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
clabbe, Zhang Rui, Michael Turquette, Icenowy Zheng, devicetree,
jason, bage, Linux PM, Maxime Ripard, linux-gpio, Rob Herring,
Thomas Gleixner, Linux ARM, Stephen Boyd,
Linux Kernel Mailing List, p.zabel
On Mon, 24 Aug 2020, Frank Lee wrote:
> ping......
"Please don't send content free pings and please allow a reasonable
time for review. People get busy, go on holiday, attend conferences
and so on so unless there is some reason for urgency (like critical
bug fixes) please allow at least a couple of weeks for review. If
there have been review comments then people may be waiting for those
to be addressed. Sending content free pings just adds to the mail
volume (if they are seen at all) and if something has gone wrong
you'll have to resend the patches anyway so [RESEND]ing with any
comments addressed is generally a much better approach."
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 13/16] dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node.
2020-07-24 7:17 ` [PATCH v5 13/16] dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node Frank Lee
@ 2020-08-25 8:02 ` Wolfram Sang
0 siblings, 0 replies; 84+ messages in thread
From: Wolfram Sang @ 2020-08-25 8:02 UTC (permalink / raw)
To: Frank Lee
Cc: gregory.clement, robh+dt, linux-i2c, devicetree, linux-kernel,
tiny.windzz, huangshuosheng, liyong, Rob Herring
[-- Attachment #1: Type: text/plain, Size: 429 bytes --]
On Fri, Jul 24, 2020 at 03:17:01PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Allwinner A100 have a mv64xxx i2c interface available to be used.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
For the record, this got upstream during the 5.9 merge window. I seem to
have forgotten to send a mail that this patch got applied. Sorry!
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 03/16] dt-bindings: pinctrl: sunxi: Get rid of continual nesting
2020-07-24 7:00 ` Frank Lee
@ 2020-08-25 8:44 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:44 UTC (permalink / raw)
To: Frank Lee
Cc: linus.walleij, robh+dt, wens, linux-gpio, devicetree,
linux-arm-kernel, linux-kernel, tiny.windzz, huangshuosheng,
liyong, Rob Herring
[-- Attachment #1: Type: text/plain, Size: 410 bytes --]
On Fri, Jul 24, 2020 at 03:00:31PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Rather than a continual nesting of 'else' clauses, just make
> each 'if' a new entry under 'allOf' and get rid of the else.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 03/16] dt-bindings: pinctrl: sunxi: Get rid of continual nesting
@ 2020-08-25 8:44 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:44 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, liyong, tiny.windzz, linus.walleij, linux-kernel,
linux-gpio, wens, robh+dt, huangshuosheng, Rob Herring,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 410 bytes --]
On Fri, Jul 24, 2020 at 03:00:31PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Rather than a continual nesting of 'else' clauses, just make
> each 'if' a new entry under 'allOf' and get rid of the else.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 04/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
2020-07-24 7:02 ` Frank Lee
@ 2020-08-25 8:44 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:44 UTC (permalink / raw)
To: Frank Lee
Cc: linus.walleij, robh+dt, wens, linux-gpio, devicetree,
linux-arm-kernel, linux-kernel, tiny.windzz, huangshuosheng,
liyong, Rob Herring
[-- Attachment #1: Type: text/plain, Size: 430 bytes --]
On Fri, Jul 24, 2020 at 03:02:42PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add device tree binding Documentation details for A100 pinctrl driver,
> which has a r pin controller and a pin controller with more irq lines.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 04/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
@ 2020-08-25 8:44 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:44 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, liyong, tiny.windzz, linus.walleij, linux-kernel,
linux-gpio, wens, robh+dt, huangshuosheng, Rob Herring,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 430 bytes --]
On Fri, Jul 24, 2020 at 03:02:42PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add device tree binding Documentation details for A100 pinctrl driver,
> which has a r pin controller and a pin controller with more irq lines.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller
2020-07-24 7:05 ` Frank Lee
@ 2020-08-25 8:45 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:45 UTC (permalink / raw)
To: Frank Lee
Cc: linus.walleij, wens, linux-kernel, linux-gpio, linux-arm-kernel,
tiny.windzz, huangshuosheng, liyong
[-- Attachment #1: Type: text/plain, Size: 302 bytes --]
On Fri, Jul 24, 2020 at 03:05:49PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> This commit introduces support for the pin controller on A100.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller
@ 2020-08-25 8:45 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:45 UTC (permalink / raw)
To: Frank Lee
Cc: liyong, tiny.windzz, linus.walleij, linux-kernel, linux-gpio,
wens, huangshuosheng, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 302 bytes --]
On Fri, Jul 24, 2020 at 03:05:49PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> This commit introduces support for the pin controller on A100.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
2020-07-24 7:10 ` Frank Lee
@ 2020-08-25 8:45 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:45 UTC (permalink / raw)
To: Frank Lee
Cc: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, wens, linux-pm, devicetree, linux-arm-kernel,
linux-kernel, huangshuosheng, liyong, Rob Herring
[-- Attachment #1: Type: text/plain, Size: 326 bytes --]
On Fri, Jul 24, 2020 at 03:10:57PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add a binding for A100's ths controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller
@ 2020-08-25 8:45 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:45 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, amit.kucheria, linux-pm, tiny.windzz, daniel.lezcano,
liyong, linux-kernel, anarsoul, wens, robh+dt, huangshuosheng,
rui.zhang, Rob Herring, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 326 bytes --]
On Fri, Jul 24, 2020 at 03:10:57PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add a binding for A100's ths controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
2020-07-24 7:11 ` Frank Lee
@ 2020-08-25 8:46 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:46 UTC (permalink / raw)
To: Frank Lee
Cc: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, wens, linux-pm, devicetree, linux-arm-kernel,
linux-kernel, huangshuosheng, liyong
[-- Attachment #1: Type: text/plain, Size: 481 bytes --]
On Fri, Jul 24, 2020 at 03:11:42PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
> calculation. On the other hand, the newer SOC may store other data in
> the space other than 12bit sensor data. Add mask operation to read data
> to avoid conversion error.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
@ 2020-08-25 8:46 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:46 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, amit.kucheria, linux-pm, tiny.windzz, daniel.lezcano,
liyong, linux-kernel, anarsoul, wens, robh+dt, huangshuosheng,
rui.zhang, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 481 bytes --]
On Fri, Jul 24, 2020 at 03:11:42PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
> calculation. On the other hand, the newer SOC may store other data in
> the space other than 12bit sensor data. Add mask operation to read data
> to avoid conversion error.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 09/16] thermal: sun8i: Add A100's THS controller support
2020-07-24 7:11 ` Frank Lee
@ 2020-08-25 8:46 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:46 UTC (permalink / raw)
To: Frank Lee
Cc: anarsoul, tiny.windzz, rui.zhang, daniel.lezcano, amit.kucheria,
robh+dt, wens, linux-pm, devicetree, linux-arm-kernel,
linux-kernel, huangshuosheng, liyong
[-- Attachment #1: Type: text/plain, Size: 340 bytes --]
On Fri, Jul 24, 2020 at 03:11:43PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> This patch add thermal sensor controller support for A100,
> which is similar to the previous ones.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 09/16] thermal: sun8i: Add A100's THS controller support
@ 2020-08-25 8:46 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:46 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, amit.kucheria, linux-pm, tiny.windzz, daniel.lezcano,
liyong, linux-kernel, anarsoul, wens, robh+dt, huangshuosheng,
rui.zhang, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 340 bytes --]
On Fri, Jul 24, 2020 at 03:11:43PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> This patch add thermal sensor controller support for A100,
> which is similar to the previous ones.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 11/16] dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
2020-07-24 7:14 ` Frank Lee
@ 2020-08-25 8:49 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:49 UTC (permalink / raw)
To: Frank Lee
Cc: tglx, jason, maz, robh+dt, wens, linux-kernel, devicetree,
linux-arm-kernel, tiny.windzz, huangshuosheng, liyong,
Rob Herring
[-- Attachment #1: Type: text/plain, Size: 357 bytes --]
On Fri, Jul 24, 2020 at 03:14:48PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> There is no one use "allwinner,sun9i-a80-sc-nmi". The A80 uses
> "allwinner,sun9i-a80-nmi".
>
> Let's fix it.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 11/16] dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi
@ 2020-08-25 8:49 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:49 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, jason, liyong, tiny.windzz, maz, linux-kernel, wens,
robh+dt, huangshuosheng, tglx, Rob Herring, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 357 bytes --]
On Fri, Jul 24, 2020 at 03:14:48PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> There is no one use "allwinner,sun9i-a80-sc-nmi". The A80 uses
> "allwinner,sun9i-a80-nmi".
>
> Let's fix it.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 12/16] dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
2020-07-24 7:15 ` Frank Lee
@ 2020-08-25 8:49 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:49 UTC (permalink / raw)
To: Frank Lee
Cc: tglx, jason, maz, robh+dt, wens, linux-kernel, devicetree,
linux-arm-kernel, tiny.windzz, huangshuosheng, liyong,
Rob Herring
[-- Attachment #1: Type: text/plain, Size: 284 bytes --]
On Fri, Jul 24, 2020 at 03:15:53PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add a binding for A100's nmi controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 12/16] dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller
@ 2020-08-25 8:49 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:49 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, jason, liyong, tiny.windzz, maz, linux-kernel, wens,
robh+dt, huangshuosheng, tglx, Rob Herring, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 284 bytes --]
On Fri, Jul 24, 2020 at 03:15:53PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add a binding for A100's nmi controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
2020-07-24 7:18 ` Frank Lee
@ 2020-08-25 8:50 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:50 UTC (permalink / raw)
To: Frank Lee
Cc: robh+dt, wens, devicetree, linux-arm-kernel, linux-kernel,
tiny.windzz, huangshuosheng, liyong
[-- Attachment #1: Type: text/plain, Size: 368 bytes --]
On Fri, Jul 24, 2020 at 03:18:24PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Allwinner A100 is a new SoC with Cortex-A53 cores, this commit adds
> the basical DTSI file of it, including the clock, i2c, pins, sid, ths,
> nmi, and UART support.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Applied, thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file
@ 2020-08-25 8:50 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:50 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, liyong, tiny.windzz, linux-kernel, wens, robh+dt,
huangshuosheng, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 368 bytes --]
On Fri, Jul 24, 2020 at 03:18:24PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Allwinner A100 is a new SoC with Cortex-A53 cores, this commit adds
> the basical DTSI file of it, including the clock, i2c, pins, sid, ths,
> nmi, and UART support.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Applied, thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 15/16] dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
2020-07-24 7:20 ` Frank Lee
@ 2020-08-25 8:50 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:50 UTC (permalink / raw)
To: Frank Lee
Cc: robh+dt, wens, icenowy, megous, clabbe, karlp, bage, devicetree,
linux-arm-kernel, linux-kernel, tiny.windzz, huangshuosheng,
liyong, Rob Herring
[-- Attachment #1: Type: text/plain, Size: 310 bytes --]
On Fri, Jul 24, 2020 at 03:20:12PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Document board compatible names for Allwinner A100 Perf1 Board.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 15/16] dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings
@ 2020-08-25 8:50 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:50 UTC (permalink / raw)
To: Frank Lee
Cc: megous, devicetree, bage, liyong, tiny.windzz, linux-kernel,
wens, robh+dt, huangshuosheng, clabbe, Rob Herring, karlp,
linux-arm-kernel, icenowy
[-- Attachment #1.1: Type: text/plain, Size: 310 bytes --]
On Fri, Jul 24, 2020 at 03:20:12PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Document board compatible names for Allwinner A100 Perf1 Board.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 16/16] arm64: allwinner: A100: add support for Allwinner Perf1 board
2020-07-24 7:21 ` Frank Lee
@ 2020-08-25 8:51 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:51 UTC (permalink / raw)
To: Frank Lee
Cc: wens, robh+dt, linux-arm-kernel, devicetree, linux-kernel,
tiny.windzz, huangshuosheng, liyong
[-- Attachment #1: Type: text/plain, Size: 470 bytes --]
On Fri, Jul 24, 2020 at 03:21:05PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> A100 perf1 is an Allwinner A100-based SBC, with the following features:
>
> - 1GiB DDR3 DRAM
> - AXP803 PMIC
> - 2 USB 2.0 ports
> - MicroSD slot and on-board eMMC module
> - on-board Nand flash
> - ···
>
> Adds initial support for it, including UART and PMU.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Applied thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 16/16] arm64: allwinner: A100: add support for Allwinner Perf1 board
@ 2020-08-25 8:51 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:51 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, liyong, tiny.windzz, linux-kernel, wens, robh+dt,
huangshuosheng, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 470 bytes --]
On Fri, Jul 24, 2020 at 03:21:05PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> A100 perf1 is an Allwinner A100-based SBC, with the following features:
>
> - 1GiB DDR3 DRAM
> - AXP803 PMIC
> - 2 USB 2.0 ports
> - MicroSD slot and on-board eMMC module
> - on-board Nand flash
> - ···
>
> Adds initial support for it, including UART and PMU.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Applied thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
2020-07-24 6:56 ` Frank Lee
@ 2020-08-25 8:52 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:52 UTC (permalink / raw)
To: Frank Lee
Cc: mturquette, sboyd, robh+dt, wens, linux-clk, devicetree,
linux-arm-kernel, linux-kernel, Rob Herring
[-- Attachment #1: Type: text/plain, Size: 307 bytes --]
On Fri, Jul 24, 2020 at 02:56:08PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> This patch adds binding to a100's ccu clock and r-ccu clock.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU
@ 2020-08-25 8:52 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:52 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, Rob Herring, sboyd, mturquette, linux-kernel, wens,
robh+dt, linux-clk, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 307 bytes --]
On Fri, Jul 24, 2020 at 02:56:08PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> This patch adds binding to a100's ccu clock and r-ccu clock.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Applied, thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
2020-07-24 6:58 ` Frank Lee
@ 2020-08-25 8:53 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:53 UTC (permalink / raw)
To: Frank Lee
Cc: mturquette, sboyd, wens, robh+dt, p.zabel, linux-kernel,
linux-clk, linux-arm-kernel, devicetree, tiny.windzz,
huangshuosheng, liyong
[-- Attachment #1: Type: text/plain, Size: 252 bytes --]
On Fri, Jul 24, 2020 at 02:58:43PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add support for a100 in the sunxi-ng CCU framework.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Applied, thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU
@ 2020-08-25 8:53 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:53 UTC (permalink / raw)
To: Frank Lee
Cc: devicetree, liyong, sboyd, mturquette, linux-kernel, tiny.windzz,
wens, robh+dt, huangshuosheng, p.zabel, linux-clk,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 252 bytes --]
On Fri, Jul 24, 2020 at 02:58:43PM +0800, Frank Lee wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add support for a100 in the sunxi-ng CCU framework.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Applied, thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-08-24 8:03 ` Lee Jones
@ 2020-08-25 8:55 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:55 UTC (permalink / raw)
To: Lee Jones
Cc: Frank Lee, Frank Lee, Rob Herring, Chen-Yu Tsai,
Michael Turquette, Stephen Boyd, gregory.clement,
Thomas Gleixner, jason, Marc Zyngier, Srini Kandagatla,
Linus Walleij, Vasily Khoruzhick, Zhang Rui, Daniel Lezcano,
Amit Kucheria, p.zabel, Icenowy Zheng, Ondřej Jirman,
clabbe, bage, devicetree, Linux ARM, Linux Kernel Mailing List,
linux-clk, linux-i2c, linux-gpio, Linux PM
[-- Attachment #1: Type: text/plain, Size: 858 bytes --]
On Mon, Aug 24, 2020 at 09:03:27AM +0100, Lee Jones wrote:
> On Mon, 24 Aug 2020, Frank Lee wrote:
>
> > ping......
>
> "Please don't send content free pings and please allow a reasonable
> time for review. People get busy, go on holiday, attend conferences
> and so on so unless there is some reason for urgency (like critical
> bug fixes) please allow at least a couple of weeks for review. If
> there have been review comments then people may be waiting for those
> to be addressed. Sending content free pings just adds to the mail
> volume (if they are seen at all) and if something has gone wrong
> you'll have to resend the patches anyway so [RESEND]ing with any
> comments addressed is generally a much better approach."
This is true to some extent, but pinging after a month doesn't seem
unreasonable either.
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-25 8:55 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-08-25 8:55 UTC (permalink / raw)
To: Lee Jones
Cc: Ondřej Jirman, Frank Lee, Linus Walleij, Srini Kandagatla,
linux-i2c, Frank Lee, linux-clk, Amit Kucheria, Marc Zyngier,
gregory.clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
clabbe, Zhang Rui, Michael Turquette, Icenowy Zheng, devicetree,
jason, bage, Linux PM, linux-gpio, Rob Herring, Thomas Gleixner,
Linux ARM, Stephen Boyd, Linux Kernel Mailing List, p.zabel
[-- Attachment #1.1: Type: text/plain, Size: 858 bytes --]
On Mon, Aug 24, 2020 at 09:03:27AM +0100, Lee Jones wrote:
> On Mon, 24 Aug 2020, Frank Lee wrote:
>
> > ping......
>
> "Please don't send content free pings and please allow a reasonable
> time for review. People get busy, go on holiday, attend conferences
> and so on so unless there is some reason for urgency (like critical
> bug fixes) please allow at least a couple of weeks for review. If
> there have been review comments then people may be waiting for those
> to be addressed. Sending content free pings just adds to the mail
> volume (if they are seen at all) and if something has gone wrong
> you'll have to resend the patches anyway so [RESEND]ing with any
> comments addressed is generally a much better approach."
This is true to some extent, but pinging after a month doesn't seem
unreasonable either.
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-08-25 8:55 ` Maxime Ripard
@ 2020-08-25 13:51 ` Wolfram Sang
-1 siblings, 0 replies; 84+ messages in thread
From: Wolfram Sang @ 2020-08-25 13:51 UTC (permalink / raw)
To: Maxime Ripard
Cc: Lee Jones, Frank Lee, Frank Lee, Rob Herring, Chen-Yu Tsai,
Michael Turquette, Stephen Boyd, gregory.clement,
Thomas Gleixner, jason, Marc Zyngier, Srini Kandagatla,
Linus Walleij, Vasily Khoruzhick, Zhang Rui, Daniel Lezcano,
Amit Kucheria, p.zabel, Icenowy Zheng, Ondřej Jirman,
clabbe, bage, devicetree, Linux ARM, Linux Kernel Mailing List,
linux-clk, linux-i2c, linux-gpio, Linux PM
[-- Attachment #1: Type: text/plain, Size: 1015 bytes --]
On Tue, Aug 25, 2020 at 10:55:32AM +0200, Maxime Ripard wrote:
> On Mon, Aug 24, 2020 at 09:03:27AM +0100, Lee Jones wrote:
> > On Mon, 24 Aug 2020, Frank Lee wrote:
> >
> > > ping......
> >
> > "Please don't send content free pings and please allow a reasonable
> > time for review. People get busy, go on holiday, attend conferences
> > and so on so unless there is some reason for urgency (like critical
> > bug fixes) please allow at least a couple of weeks for review. If
> > there have been review comments then people may be waiting for those
> > to be addressed. Sending content free pings just adds to the mail
> > volume (if they are seen at all) and if something has gone wrong
> > you'll have to resend the patches anyway so [RESEND]ing with any
> > comments addressed is generally a much better approach."
>
> This is true to some extent, but pinging after a month doesn't seem
> unreasonable either.
Especially if resending would mean up to 16 patches sent again.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-25 13:51 ` Wolfram Sang
0 siblings, 0 replies; 84+ messages in thread
From: Wolfram Sang @ 2020-08-25 13:51 UTC (permalink / raw)
To: Maxime Ripard
Cc: Ondřej Jirman, Frank Lee, Linus Walleij, Srini Kandagatla,
linux-i2c, Frank Lee, Lee Jones, linux-clk, Amit Kucheria,
Marc Zyngier, gregory.clement, Daniel Lezcano, Vasily Khoruzhick,
Chen-Yu Tsai, clabbe, Zhang Rui, Michael Turquette,
Icenowy Zheng, devicetree, jason, bage, Linux PM, linux-gpio,
Rob Herring, Thomas Gleixner, Linux ARM, Stephen Boyd,
Linux Kernel Mailing List, p.zabel
[-- Attachment #1.1: Type: text/plain, Size: 1015 bytes --]
On Tue, Aug 25, 2020 at 10:55:32AM +0200, Maxime Ripard wrote:
> On Mon, Aug 24, 2020 at 09:03:27AM +0100, Lee Jones wrote:
> > On Mon, 24 Aug 2020, Frank Lee wrote:
> >
> > > ping......
> >
> > "Please don't send content free pings and please allow a reasonable
> > time for review. People get busy, go on holiday, attend conferences
> > and so on so unless there is some reason for urgency (like critical
> > bug fixes) please allow at least a couple of weeks for review. If
> > there have been review comments then people may be waiting for those
> > to be addressed. Sending content free pings just adds to the mail
> > volume (if they are seen at all) and if something has gone wrong
> > you'll have to resend the patches anyway so [RESEND]ing with any
> > comments addressed is generally a much better approach."
>
> This is true to some extent, but pinging after a month doesn't seem
> unreasonable either.
Especially if resending would mean up to 16 patches sent again.
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-08-25 8:55 ` Maxime Ripard
@ 2020-08-25 13:53 ` Lee Jones
-1 siblings, 0 replies; 84+ messages in thread
From: Lee Jones @ 2020-08-25 13:53 UTC (permalink / raw)
To: Maxime Ripard
Cc: Frank Lee, Frank Lee, Rob Herring, Chen-Yu Tsai,
Michael Turquette, Stephen Boyd, gregory.clement,
Thomas Gleixner, jason, Marc Zyngier, Srini Kandagatla,
Linus Walleij, Vasily Khoruzhick, Zhang Rui, Daniel Lezcano,
Amit Kucheria, p.zabel, Icenowy Zheng, Ondřej Jirman,
clabbe, bage, devicetree, Linux ARM, Linux Kernel Mailing List,
linux-clk, linux-i2c, linux-gpio, Linux PM
On Tue, 25 Aug 2020, Maxime Ripard wrote:
> On Mon, Aug 24, 2020 at 09:03:27AM +0100, Lee Jones wrote:
> > On Mon, 24 Aug 2020, Frank Lee wrote:
> >
> > > ping......
> >
> > "Please don't send content free pings and please allow a reasonable
> > time for review. People get busy, go on holiday, attend conferences
> > and so on so unless there is some reason for urgency (like critical
> > bug fixes) please allow at least a couple of weeks for review. If
> > there have been review comments then people may be waiting for those
> > to be addressed. Sending content free pings just adds to the mail
> > volume (if they are seen at all) and if something has gone wrong
> > you'll have to resend the patches anyway so [RESEND]ing with any
> > comments addressed is generally a much better approach."
>
> This is true to some extent, but pinging after a month doesn't seem
> unreasonable either.
Pinging is mostly a fruitless exercise.
After a month, many Maintainers would have purged any un-serviced
mails anyway. If a patch-set is left hanging, still requiring
attention before the next version, submitting a [RESEND] is generally
a better option.
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-25 13:53 ` Lee Jones
0 siblings, 0 replies; 84+ messages in thread
From: Lee Jones @ 2020-08-25 13:53 UTC (permalink / raw)
To: Maxime Ripard
Cc: Ondřej Jirman, Frank Lee, Linus Walleij, Srini Kandagatla,
linux-i2c, Frank Lee, linux-clk, Amit Kucheria, Marc Zyngier,
gregory.clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
clabbe, Zhang Rui, Michael Turquette, Icenowy Zheng, devicetree,
jason, bage, Linux PM, linux-gpio, Rob Herring, Thomas Gleixner,
Linux ARM, Stephen Boyd, Linux Kernel Mailing List, p.zabel
On Tue, 25 Aug 2020, Maxime Ripard wrote:
> On Mon, Aug 24, 2020 at 09:03:27AM +0100, Lee Jones wrote:
> > On Mon, 24 Aug 2020, Frank Lee wrote:
> >
> > > ping......
> >
> > "Please don't send content free pings and please allow a reasonable
> > time for review. People get busy, go on holiday, attend conferences
> > and so on so unless there is some reason for urgency (like critical
> > bug fixes) please allow at least a couple of weeks for review. If
> > there have been review comments then people may be waiting for those
> > to be addressed. Sending content free pings just adds to the mail
> > volume (if they are seen at all) and if something has gone wrong
> > you'll have to resend the patches anyway so [RESEND]ing with any
> > comments addressed is generally a much better approach."
>
> This is true to some extent, but pinging after a month doesn't seem
> unreasonable either.
Pinging is mostly a fruitless exercise.
After a month, many Maintainers would have purged any un-serviced
mails anyway. If a patch-set is left hanging, still requiring
attention before the next version, submitting a [RESEND] is generally
a better option.
--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-07-24 6:52 ` Frank Lee
@ 2020-08-28 10:02 ` Linus Walleij
-1 siblings, 0 replies; 84+ messages in thread
From: Linus Walleij @ 2020-08-28 10:02 UTC (permalink / raw)
To: Frank Lee
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Michael Turquette,
Stephen Boyd, Gregory Clement, Thomas Gleixner, Jason Cooper,
Marc Zyngier, Srini Kandagatla, Vasily Khoruzhick, Frank Lee,
Zhang Rui, Daniel Lezcano, Amit Kucheria, Lee Jones,
Philipp Zabel, Icenowy Zheng, Ondrej Jirman, Corentin Labbe,
bage, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux ARM, linux-kernel, linux-clk, linux-i2c,
open list:GPIO SUBSYSTEM, Linux PM list
On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
Shall I commit the pinctrl patches (if Maxime ACKed) separately
or not? Once Maxime is happy, I am usually happy too.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-28 10:02 ` Linus Walleij
0 siblings, 0 replies; 84+ messages in thread
From: Linus Walleij @ 2020-08-28 10:02 UTC (permalink / raw)
To: Frank Lee
Cc: Ondrej Jirman, Frank Lee, Michael Turquette, Srini Kandagatla,
linux-i2c, Lee Jones, linux-clk, Amit Kucheria, Marc Zyngier,
Gregory Clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
Corentin Labbe, Zhang Rui, Icenowy Zheng,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Jason Cooper, bage, Linux PM list, Maxime Ripard,
open list:GPIO SUBSYSTEM, Rob Herring, Thomas Gleixner,
Linux ARM, Stephen Boyd, linux-kernel, Philipp Zabel
On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
Shall I commit the pinctrl patches (if Maxime ACKed) separately
or not? Once Maxime is happy, I am usually happy too.
Yours,
Linus Walleij
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-08-28 10:02 ` Linus Walleij
@ 2020-08-28 11:20 ` Frank Lee
-1 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-08-28 11:20 UTC (permalink / raw)
To: Linus Walleij
Cc: Frank Lee, Rob Herring, Maxime Ripard, Chen-Yu Tsai,
Michael Turquette, Stephen Boyd, Gregory Clement,
Thomas Gleixner, Jason Cooper, Marc Zyngier, Srini Kandagatla,
Vasily Khoruzhick, Zhang Rui, Daniel Lezcano, Amit Kucheria,
Lee Jones, Philipp Zabel, Icenowy Zheng, Ondrej Jirman,
Corentin Labbe, bage,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux ARM, linux-kernel, linux-clk, linux-i2c,
open list:GPIO SUBSYSTEM, Linux PM list
HI Linus,
On Fri, Aug 28, 2020 at 6:02 PM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
>
> > This patch set adds initial support for allwinner a100 soc,
> > which is a 64-bit tablet chip.
>
> Shall I commit the pinctrl patches (if Maxime ACKed) separately
> or not? Once Maxime is happy, I am usually happy too.
Maxime told me he wanted you to commit the pinctrl patches.
Thx,
Yangtao
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-08-28 11:20 ` Frank Lee
0 siblings, 0 replies; 84+ messages in thread
From: Frank Lee @ 2020-08-28 11:20 UTC (permalink / raw)
To: Linus Walleij
Cc: Ondrej Jirman, Michael Turquette, Srini Kandagatla, linux-i2c,
Frank Lee, Lee Jones, linux-clk, Amit Kucheria, Marc Zyngier,
Gregory Clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
Corentin Labbe, Zhang Rui, Icenowy Zheng,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Jason Cooper, bage, Linux PM list, Maxime Ripard,
open list:GPIO SUBSYSTEM, Rob Herring, Thomas Gleixner,
Linux ARM, Stephen Boyd, linux-kernel, Philipp Zabel
HI Linus,
On Fri, Aug 28, 2020 at 6:02 PM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
>
> > This patch set adds initial support for allwinner a100 soc,
> > which is a 64-bit tablet chip.
>
> Shall I commit the pinctrl patches (if Maxime ACKed) separately
> or not? Once Maxime is happy, I am usually happy too.
Maxime told me he wanted you to commit the pinctrl patches.
Thx,
Yangtao
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-08-28 10:02 ` Linus Walleij
@ 2020-09-01 9:35 ` Maxime Ripard
-1 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-09-01 9:35 UTC (permalink / raw)
To: Linus Walleij
Cc: Frank Lee, Rob Herring, Chen-Yu Tsai, Michael Turquette,
Stephen Boyd, Gregory Clement, Thomas Gleixner, Jason Cooper,
Marc Zyngier, Srini Kandagatla, Vasily Khoruzhick, Frank Lee,
Zhang Rui, Daniel Lezcano, Amit Kucheria, Lee Jones,
Philipp Zabel, Icenowy Zheng, Ondrej Jirman, Corentin Labbe,
bage, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux ARM, linux-kernel, linux-clk, linux-i2c,
open list:GPIO SUBSYSTEM, Linux PM list
[-- Attachment #1: Type: text/plain, Size: 445 bytes --]
Hi Linus
On Fri, Aug 28, 2020 at 12:02:29PM +0200, Linus Walleij wrote:
> On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
>
> > This patch set adds initial support for allwinner a100 soc,
> > which is a 64-bit tablet chip.
>
> Shall I commit the pinctrl patches (if Maxime ACKed) separately
> or not? Once Maxime is happy, I am usually happy too.
Yeah, you can apply it to your tree
Thanks!
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-09-01 9:35 ` Maxime Ripard
0 siblings, 0 replies; 84+ messages in thread
From: Maxime Ripard @ 2020-09-01 9:35 UTC (permalink / raw)
To: Linus Walleij
Cc: Ondrej Jirman, Frank Lee, Michael Turquette, Srini Kandagatla,
linux-i2c, Frank Lee, Lee Jones, linux-clk, Amit Kucheria,
Marc Zyngier, Gregory Clement, Daniel Lezcano, Vasily Khoruzhick,
Chen-Yu Tsai, Corentin Labbe, Zhang Rui, Icenowy Zheng,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Jason Cooper, bage, Linux PM list, open list:GPIO SUBSYSTEM,
Rob Herring, Thomas Gleixner, Linux ARM, Stephen Boyd,
linux-kernel, Philipp Zabel
[-- Attachment #1.1: Type: text/plain, Size: 445 bytes --]
Hi Linus
On Fri, Aug 28, 2020 at 12:02:29PM +0200, Linus Walleij wrote:
> On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
>
> > This patch set adds initial support for allwinner a100 soc,
> > which is a 64-bit tablet chip.
>
> Shall I commit the pinctrl patches (if Maxime ACKed) separately
> or not? Once Maxime is happy, I am usually happy too.
Yeah, you can apply it to your tree
Thanks!
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-07-24 6:52 ` Frank Lee
@ 2020-09-12 10:36 ` Linus Walleij
-1 siblings, 0 replies; 84+ messages in thread
From: Linus Walleij @ 2020-09-12 10:36 UTC (permalink / raw)
To: Frank Lee
Cc: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Michael Turquette,
Stephen Boyd, Gregory Clement, Thomas Gleixner, Jason Cooper,
Marc Zyngier, Srini Kandagatla, Vasily Khoruzhick, Frank Lee,
Zhang Rui, Daniel Lezcano, Amit Kucheria, Lee Jones,
Philipp Zabel, Icenowy Zheng, Ondrej Jirman, Corentin Labbe,
bage, open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux ARM, linux-kernel, linux-clk, linux-i2c,
open list:GPIO SUBSYSTEM, Linux PM list
On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
> dt-bindings: pinctrl: sunxi: Get rid of continual nesting
> dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
> pinctrl: sunxi: add support for the Allwinner A100 pin controller
These three patches (3,4,5) are now applied to the pinctrl tree.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-09-12 10:36 ` Linus Walleij
0 siblings, 0 replies; 84+ messages in thread
From: Linus Walleij @ 2020-09-12 10:36 UTC (permalink / raw)
To: Frank Lee
Cc: Ondrej Jirman, Frank Lee, Michael Turquette, Srini Kandagatla,
linux-i2c, Lee Jones, linux-clk, Amit Kucheria, Marc Zyngier,
Gregory Clement, Daniel Lezcano, Vasily Khoruzhick, Chen-Yu Tsai,
Corentin Labbe, Zhang Rui, Icenowy Zheng,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Jason Cooper, bage, Linux PM list, Maxime Ripard,
open list:GPIO SUBSYSTEM, Rob Herring, Thomas Gleixner,
Linux ARM, Stephen Boyd, linux-kernel, Philipp Zabel
On Fri, Jul 24, 2020 at 8:53 AM Frank Lee <frank@allwinnertech.com> wrote:
> dt-bindings: pinctrl: sunxi: Get rid of continual nesting
> dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings
> pinctrl: sunxi: add support for the Allwinner A100 pin controller
These three patches (3,4,5) are now applied to the pinctrl tree.
Yours,
Linus Walleij
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
2020-07-24 6:52 ` Frank Lee
@ 2020-09-22 15:37 ` Daniel Lezcano
-1 siblings, 0 replies; 84+ messages in thread
From: Daniel Lezcano @ 2020-09-22 15:37 UTC (permalink / raw)
To: Frank Lee, robh+dt, mripard, wens, mturquette, sboyd,
gregory.clement, tglx, jason, maz, srinivas.kandagatla,
linus.walleij, anarsoul, tiny.windzz, rui.zhang, amit.kucheria,
lee.jones, p.zabel, icenowy, megous, clabbe, bage, devicetree
Cc: linux-arm-kernel, linux-kernel, linux-clk, linux-i2c, linux-gpio,
linux-pm
On 24/07/2020 08:52, Frank Lee wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
Applied patches 7,8,9
Thanks
-- Daniel
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 84+ messages in thread
* Re: [PATCH v5 00/16] Allwinner A100 Initial support
@ 2020-09-22 15:37 ` Daniel Lezcano
0 siblings, 0 replies; 84+ messages in thread
From: Daniel Lezcano @ 2020-09-22 15:37 UTC (permalink / raw)
To: Frank Lee, robh+dt, mripard, wens, mturquette, sboyd,
gregory.clement, tglx, jason, maz, srinivas.kandagatla,
linus.walleij, anarsoul, tiny.windzz, rui.zhang, amit.kucheria,
lee.jones, p.zabel, icenowy, megous, clabbe, bage, devicetree
Cc: linux-pm, linux-kernel, linux-gpio, linux-i2c, linux-clk,
linux-arm-kernel
On 24/07/2020 08:52, Frank Lee wrote:
> This patch set adds initial support for allwinner a100 soc,
> which is a 64-bit tablet chip.
Applied patches 7,8,9
Thanks
-- Daniel
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 84+ messages in thread
end of thread, other threads:[~2020-09-22 15:38 UTC | newest]
Thread overview: 84+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-24 6:52 [PATCH v5 00/16] Allwinner A100 Initial support Frank Lee
2020-07-24 6:52 ` Frank Lee
2020-07-24 6:56 ` [PATCH v5 01/16] dt-bindings: clk: sunxi-ccu: add compatible string for A100 CCU and R-CCU Frank Lee
2020-07-24 6:56 ` Frank Lee
2020-08-25 8:52 ` Maxime Ripard
2020-08-25 8:52 ` Maxime Ripard
2020-07-24 6:58 ` [PATCH v5 02/16] clk: sunxi-ng: add support for the Allwinner A100 CCU Frank Lee
2020-07-24 6:58 ` Frank Lee
2020-07-27 19:57 ` Rob Herring
2020-07-27 19:57 ` Rob Herring
2020-08-25 8:53 ` Maxime Ripard
2020-08-25 8:53 ` Maxime Ripard
2020-07-24 7:00 ` [PATCH v5 03/16] dt-bindings: pinctrl: sunxi: Get rid of continual nesting Frank Lee
2020-07-24 7:00 ` Frank Lee
2020-08-25 8:44 ` Maxime Ripard
2020-08-25 8:44 ` Maxime Ripard
2020-07-24 7:02 ` [PATCH v5 04/16] dt-bindings: pinctrl: sunxi: Add A100 pinctrl bindings Frank Lee
2020-07-24 7:02 ` Frank Lee
2020-08-25 8:44 ` Maxime Ripard
2020-08-25 8:44 ` Maxime Ripard
2020-07-24 7:05 ` [PATCH v5 05/16] pinctrl: sunxi: add support for the Allwinner A100 pin controller Frank Lee
2020-07-24 7:05 ` Frank Lee
2020-08-25 8:45 ` Maxime Ripard
2020-08-25 8:45 ` Maxime Ripard
2020-07-24 7:09 ` [PATCH v5 06/16] dt-bindings: nvmem: SID: add binding for A100's SID controller Frank Lee
2020-07-24 7:09 ` Frank Lee
2020-07-24 7:10 ` [PATCH v5 07/16] dt-bindings: thermal: sun8i: Add binding for A100's THS controller Frank Lee
2020-07-24 7:10 ` Frank Lee
2020-08-25 8:45 ` Maxime Ripard
2020-08-25 8:45 ` Maxime Ripard
2020-07-24 7:11 ` [PATCH v5 08/16] thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate Frank Lee
2020-07-24 7:11 ` Frank Lee
2020-08-25 8:46 ` Maxime Ripard
2020-08-25 8:46 ` Maxime Ripard
2020-07-24 7:11 ` [PATCH v5 09/16] thermal: sun8i: Add A100's THS controller support Frank Lee
2020-07-24 7:11 ` Frank Lee
2020-08-25 8:46 ` Maxime Ripard
2020-08-25 8:46 ` Maxime Ripard
2020-07-24 7:13 ` [PATCH v5 10/16] mfd: axp20x: Allow the AXP803 to be probed by I2C Frank Lee
2020-07-27 15:36 ` Lee Jones
2020-07-24 7:14 ` [PATCH v5 11/16] dt-bindings: irq: sun7i-nmi: fix dt-binding for a80 nmi Frank Lee
2020-07-24 7:14 ` Frank Lee
2020-08-25 8:49 ` Maxime Ripard
2020-08-25 8:49 ` Maxime Ripard
2020-07-24 7:15 ` [PATCH v5 12/16] dt-bindings: irq: sun7i-nmi: Add binding for A100's NMI controller Frank Lee
2020-07-24 7:15 ` Frank Lee
2020-08-25 8:49 ` Maxime Ripard
2020-08-25 8:49 ` Maxime Ripard
2020-07-24 7:17 ` [PATCH v5 13/16] dt-bindings: i2c: mv64xxx: Add compatible for the A100 i2c node Frank Lee
2020-08-25 8:02 ` Wolfram Sang
2020-07-24 7:18 ` [PATCH v5 14/16] arm64: allwinner: A100: add the basical Allwinner A100 DTSI file Frank Lee
2020-07-24 7:18 ` Frank Lee
2020-08-25 8:50 ` Maxime Ripard
2020-08-25 8:50 ` Maxime Ripard
2020-07-24 7:20 ` [PATCH v5 15/16] dt-bindings: arm: sunxi: Add Allwinner A100 Perf1 Board bindings Frank Lee
2020-07-24 7:20 ` Frank Lee
2020-08-25 8:50 ` Maxime Ripard
2020-08-25 8:50 ` Maxime Ripard
2020-07-24 7:21 ` [PATCH v5 16/16] arm64: allwinner: A100: add support for Allwinner Perf1 board Frank Lee
2020-07-24 7:21 ` Frank Lee
2020-08-25 8:51 ` Maxime Ripard
2020-08-25 8:51 ` Maxime Ripard
2020-07-30 1:20 ` [PATCH v5 00/16] Allwinner A100 Initial support Frank Lee
2020-07-30 1:20 ` Frank Lee
2020-08-24 7:44 ` Frank Lee
2020-08-24 7:44 ` Frank Lee
2020-08-24 8:03 ` Lee Jones
2020-08-24 8:03 ` Lee Jones
2020-08-25 8:55 ` Maxime Ripard
2020-08-25 8:55 ` Maxime Ripard
2020-08-25 13:51 ` Wolfram Sang
2020-08-25 13:51 ` Wolfram Sang
2020-08-25 13:53 ` Lee Jones
2020-08-25 13:53 ` Lee Jones
2020-08-28 10:02 ` Linus Walleij
2020-08-28 10:02 ` Linus Walleij
2020-08-28 11:20 ` Frank Lee
2020-08-28 11:20 ` Frank Lee
2020-09-01 9:35 ` Maxime Ripard
2020-09-01 9:35 ` Maxime Ripard
2020-09-12 10:36 ` Linus Walleij
2020-09-12 10:36 ` Linus Walleij
2020-09-22 15:37 ` Daniel Lezcano
2020-09-22 15:37 ` Daniel Lezcano
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.