Re: [BUG] bcm2711: bad_chained_irq in brcmstb_l2_intc_irq_handle

[Stefan Wahren <stefan.wahren@i2se.com>]

Hi Maxime,

Am 20.01.22 um 16:39 schrieb Maxime Ripard:
> Hi Stefan,
>
> On Sun, Jan 16, 2022 at 06:26:58PM +0100, Stefan Wahren wrote:
>> recently i saw a report [1] about bad chained IRQ with Linux 5.15.13
>> Aarch64 with Arch Linux. I'm able to reproduce this issue on my
>> Raspberry Pi 4 B (8 GB RAM, Firmware: 2022-01-06T15:39:30) by turning
>> the connected HDMI monitor off and on again.
> By turning the monitor on and off, you mean that you used the power
> button on it?
yes, correct
>  Not something like disabling the output in sysfs, right?
>
>> Kernel output is the following:
>>
>> [15053.285438] irq 10, desc: 00000000acc41fca, depth: 0, count: 0,
>> unhandled: 0
>> [15053.295440] ->handle_irq():  00000000b28cf1d1,
>> brcmstb_l2_intc_irq_handle+0x0/0x1e0
>> [15053.306049] ->irq_data.chip(): 000000005f172760, gic_data+0x0/0x768
>> [15053.315233] ->action(): 00000000236e815e
>> [15053.322022] ->action->handler(): 0000000013023289,
>> bad_chained_irq+0x0/0x50
>> [15053.331909]      IRQ_LEVEL set
>> [15053.337822]    IRQ_NOPROBE set
>> [15053.343715]  IRQ_NOREQUEST set
>> [15053.349585]   IRQ_NOTHREAD set
> IRQ10 is the interrupt that a monitor has been connected on HDMI1, which
> makes sense if you were using HDMI1.

The irq number in this output is always 10 regardless of the used HDMI
connector (0 or 1). So maybe it's the hardware interrupt? Also in the
interrupts list there is a interrupt with number 10 in the first column,
which has the name (null) and it's count is identical to the occured
warnings.

[    0.000000] irq_brcmstb_l2: registered L2 intc
(/soc/interrupt-controller@7ef00100, parent irq: 10)

>  Usually, when a display is turned
> on, it will issue a pulse on the HPD line so we would have a
> disconnection interrupt followed by a connection interrupt.
>
> This is weird though, since we have an interrupt handler on that
> interrupt (hpd-connected in the DT binding):
> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/vc4/vc4_hdmi.c#L1578

I played a little bit with turn on/off and it seems the connect
interrupts get lost sometimes (see below). I mean the warning doesn't
occur always, it happens most of the time.

reduced /proc/interrupts for HDMI 0 case:

 10:          5          0          0          0     GICv2 128 Level    
(null)
 ...

 43:          1          0          0          0 
interrupt-controller@7ef00100   0 Edge      vc4 hdmi cec tx
 44:          0          0          0          0 
interrupt-controller@7ef00100   1 Edge      vc4 hdmi cec rx
 47:          4          0          0          0 
interrupt-controller@7ef00100   4 Edge      vc4 hdmi hpd connected
 48:          7          0          0          0 
interrupt-controller@7ef00100   5 Edge      vc4 hdmi hpd disconnected
 49:          0          0          0          0 
interrupt-controller@7ef00100   8 Edge      vc4 hdmi cec tx
 50:          0          0          0          0 
interrupt-controller@7ef00100   7 Edge      vc4 hdmi cec rx
 53:          0          0          0          0 
interrupt-controller@7ef00100  10 Edge      vc4 hdmi hpd connected
 54:          0          0          0          0 
interrupt-controller@7ef00100  11 Edge      vc4 hdmi hpd disconnected

...

Err:          5

/proc/interrupts for HDMI 1 case:

 10:          6          0          0          0     GICv2 128 Level    
(null)
...
 43:          0          0          0          0 
interrupt-controller@7ef00100   0 Edge      vc4 hdmi cec tx
 44:          0          0          0          0 
interrupt-controller@7ef00100   1 Edge      vc4 hdmi cec rx
 47:          0          0          0          0 
interrupt-controller@7ef00100   4 Edge      vc4 hdmi hpd connected
 48:          0          0          0          0 
interrupt-controller@7ef00100   5 Edge      vc4 hdmi hpd disconnected
 49:          0          0          0          0 
interrupt-controller@7ef00100   8 Edge      vc4 hdmi cec tx
 50:          0          0          0          0 
interrupt-controller@7ef00100   7 Edge      vc4 hdmi cec rx
 53:          3          0          0          0 
interrupt-controller@7ef00100  10 Edge      vc4 hdmi hpd connected
 54:          7          0          0          0 
interrupt-controller@7ef00100  11 Edge      vc4 hdmi hpd disconnected

...

Err:          6

I could send a diff of the config against arm64/defconfig? Contrary to
the Raspberry Pi OS, Arch Linux uses U-Boot not sure this is related.

Regards


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel