All of lore.kernel.org
 help / color / mirror / Atom feed
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
To: linux-sh@vger.kernel.org
Subject: [PATCH 5/6] ARM: mach-shmobile: kzm9g: add LCDC support
Date: Wed, 11 Apr 2012 03:58:33 +0000	[thread overview]
Message-ID: <877gxm3onu.wl%kuninori.morimoto.gx@renesas.com> (raw)

AS3711 chip initalization is required for enabling LCDC backlight,
but there is no driver for this chip.
So, this patch sends its settings when boot.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
 arch/arm/mach-shmobile/board-kzm9g.c |  143 ++++++++++++++++++++++++++++++++++
 1 files changed, 143 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-shmobile/board-kzm9g.c b/arch/arm/mach-shmobile/board-kzm9g.c
index f48db23..145341d 100644
--- a/arch/arm/mach-shmobile/board-kzm9g.c
+++ b/arch/arm/mach-shmobile/board-kzm9g.c
@@ -16,12 +16,15 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
+
+#include <linux/delay.h>
 #include <linux/gpio.h>
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/platform_device.h>
 #include <linux/smsc911x.h>
 #include <linux/usb/r8a66597.h>
+#include <linux/videodev2.h>
 #include <mach/irqs.h>
 #include <mach/sh73a0.h>
 #include <mach/common.h>
@@ -29,6 +32,7 @@
 #include <asm/hardware/gic.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
+#include <video/sh_mobile_lcdc.h>
 
 /* SMSC 9221 */
 static struct resource smsc9221_resources[] = {
@@ -88,11 +92,119 @@ static struct platform_device usb_host_device = {
 	.resource	= usb_resources,
 };
 
+/* LCDC */
+static struct fb_videomode kzm_lcdc_mode = {
+	.name		= "WVGA Panel",
+	.xres		= 800,
+	.yres		= 480,
+	.left_margin	= 220,
+	.right_margin	= 110,
+	.hsync_len	= 70,
+	.upper_margin	= 20,
+	.lower_margin	= 5,
+	.vsync_len	= 5,
+	.sync		= 0,
+};
+
+static struct sh_mobile_lcdc_info lcdc_info = {
+	.clock_source = LCDC_CLK_BUS,
+	.ch[0] = {
+		.chan		= LCDC_CHAN_MAINLCD,
+		.fourcc		= V4L2_PIX_FMT_RGB565,
+		.interface_type	= RGB24,
+		.lcd_modes	= &kzm_lcdc_mode,
+		.num_modes	= 1,
+		.clock_divider	= 5,
+		.flags		= 0,
+		.panel_cfg = {
+			.width	= 152,
+			.height	= 91,
+		},
+	}
+};
+
+static struct resource lcdc_resources[] = {
+	[0] = {
+		.name	= "LCDC",
+		.start	= 0xfe940000,
+		.end	= 0xfe943fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= intcs_evt2irq(0x580),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device lcdc_device = {
+	.name		= "sh_mobile_lcdc_fb",
+	.num_resources	= ARRAY_SIZE(lcdc_resources),
+	.resource	= lcdc_resources,
+	.dev	= {
+		.platform_data	= &lcdc_info,
+		.coherent_dma_mask = ~0,
+	},
+};
+
 static struct platform_device *kzm_devices[] __initdata = {
 	&smsc_device,
 	&usb_host_device,
+	&lcdc_device,
 };
 
+/*
+ * FIXME
+ *
+ * This is quick hack for enabling LCDC backlight
+ */
+static int __init as3711_enable_lcdc_backlight(void)
+{
+	struct i2c_adapter *a = i2c_get_adapter(0);
+	struct i2c_msg msg;
+	int i, ret;
+	__u8 magic[] = {
+		0x40, 0x2a,
+		0x43, 0x3c,
+		0x44, 0x3c,
+		0x45, 0x3c,
+		0x54, 0x03,
+		0x51, 0x00,
+		0x51, 0x01,
+		0xff, 0x00, /* wait */
+		0x43, 0xf0,
+		0x44, 0xf0,
+		0x45, 0xf0,
+	};
+
+	if (!machine_is_kzm9g())
+		return 0;
+
+	if (!a)
+		return 0;
+
+	msg.addr	= 0x40;
+	msg.len		= 2;
+	msg.flags	= 0;
+
+	for (i = 0; i < ARRAY_SIZE(magic); i += 2) {
+		msg.buf = magic + i;
+
+		if (0xff = msg.buf[0]) {
+			udelay(500);
+			continue;
+		}
+
+		ret = i2c_transfer(a, &msg, 1);
+		if (ret < 0) {
+			pr_err("i2c transfer fail\n");
+			break;
+		}
+	}
+
+	return 0;
+}
+device_initcall(as3711_enable_lcdc_backlight);
+
 static void __init kzm_init(void)
 {
 	sh73a0_pinmux_init();
@@ -110,6 +222,37 @@ static void __init kzm_init(void)
 	gpio_request(GPIO_PORT224, NULL); /* IRQ3 */
 	gpio_direction_input(GPIO_PORT224);
 
+	/* LCDC */
+	gpio_request(GPIO_FN_LCDD23,	NULL);
+	gpio_request(GPIO_FN_LCDD22,	NULL);
+	gpio_request(GPIO_FN_LCDD21,	NULL);
+	gpio_request(GPIO_FN_LCDD20,	NULL);
+	gpio_request(GPIO_FN_LCDD19,	NULL);
+	gpio_request(GPIO_FN_LCDD18,	NULL);
+	gpio_request(GPIO_FN_LCDD17,	NULL);
+	gpio_request(GPIO_FN_LCDD16,	NULL);
+	gpio_request(GPIO_FN_LCDD15,	NULL);
+	gpio_request(GPIO_FN_LCDD14,	NULL);
+	gpio_request(GPIO_FN_LCDD13,	NULL);
+	gpio_request(GPIO_FN_LCDD12,	NULL);
+	gpio_request(GPIO_FN_LCDD11,	NULL);
+	gpio_request(GPIO_FN_LCDD10,	NULL);
+	gpio_request(GPIO_FN_LCDD9,	NULL);
+	gpio_request(GPIO_FN_LCDD8,	NULL);
+	gpio_request(GPIO_FN_LCDD7,	NULL);
+	gpio_request(GPIO_FN_LCDD6,	NULL);
+	gpio_request(GPIO_FN_LCDD5,	NULL);
+	gpio_request(GPIO_FN_LCDD4,	NULL);
+	gpio_request(GPIO_FN_LCDD3,	NULL);
+	gpio_request(GPIO_FN_LCDD2,	NULL);
+	gpio_request(GPIO_FN_LCDD1,	NULL);
+	gpio_request(GPIO_FN_LCDD0,	NULL);
+	gpio_request(GPIO_FN_LCDDISP,	NULL);
+	gpio_request(GPIO_FN_LCDDCK,	NULL);
+
+	gpio_request(GPIO_PORT222,	NULL);
+	gpio_direction_output(GPIO_PORT222, 1);
+
 #ifdef CONFIG_CACHE_L2X0
 	/* Early BRESP enable, Shared attribute override enable, 64K*8way */
 	l2x0_init(IOMEM(0xf0100000), 0x40460000, 0x82000fff);
-- 
1.7.5.4


             reply	other threads:[~2012-04-11  3:58 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-04-11  3:58 Kuninori Morimoto [this message]
2012-04-23  6:53 ` [PATCH 5/6] ARM: mach-shmobile: kzm9g: add SDHI support Kuninori Morimoto

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=877gxm3onu.wl%kuninori.morimoto.gx@renesas.com \
    --to=kuninori.morimoto.gx@renesas.com \
    --cc=linux-sh@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.