From: Kalle Valo <kvalo@qca.qualcomm.com>
To: <ath10k@lists.infradead.org>
Cc: <linux-wireless@vger.kernel.org>
Subject: Re: [PATCH v2 0/8] ath10k: Add thermal mitigation support
Date: Tue, 23 Dec 2014 17:21:47 +0200 [thread overview]
Message-ID: <87k31ie6ic.fsf@kamboji.qca.qualcomm.com> (raw)
In-Reply-To: <20141217101755.15964.2625.stgit@potku.adurom.net> (Kalle Valo's message of "Wed, 17 Dec 2014 12:20:35 +0200")
Kalle Valo <kvalo@qca.qualcomm.com> writes:
> The following patches add thermal sensor and thermal cooling device
> support in ath10k. For sensor, hwmon interface is used. For controlling
> temperature cooling device interface is used. For thermal mitigation,
> tx throttling is done using hw MAC quiet time setting.
>
> v2:
>
> * use ATH10K_FW_IE_WMI_OP_VERSION instead of a feature flag
>
> * add separate wmi mappings for 10.2.4
>
> * bump up FW API to 4
>
> * new patch: ath10k: set max_num_vdevs based on wmi op version
>
> * new patch: ath10k: use wmi op version to check which iface
> combination to use
>
> * new patch: ath10k: print ath10k wmi op version
>
> ---
>
> Kalle Valo (3):
> ath10k: set max_num_vdevs based on wmi op version
> ath10k: use wmi op version to check which iface combination to use
> ath10k: print ath10k wmi op version
>
> Rajkumar Manoharan (5):
> ath10k: add 10.2.4 firmware support
> ath10k: add wmi support for pdev_set_quiet_mode
> ath10k: add thermal cooling device support
> ath10k: add wmi interface for pdev_get_temperature
> ath10k: add thermal sensor device support
All eight patches applied, thanks Rajkumar.
--
Kalle Valo
WARNING: multiple messages have this Message-ID (diff)
From: Kalle Valo <kvalo@qca.qualcomm.com>
To: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Subject: Re: [PATCH v2 0/8] ath10k: Add thermal mitigation support
Date: Tue, 23 Dec 2014 17:21:47 +0200 [thread overview]
Message-ID: <87k31ie6ic.fsf@kamboji.qca.qualcomm.com> (raw)
In-Reply-To: <20141217101755.15964.2625.stgit@potku.adurom.net> (Kalle Valo's message of "Wed, 17 Dec 2014 12:20:35 +0200")
Kalle Valo <kvalo@qca.qualcomm.com> writes:
> The following patches add thermal sensor and thermal cooling device
> support in ath10k. For sensor, hwmon interface is used. For controlling
> temperature cooling device interface is used. For thermal mitigation,
> tx throttling is done using hw MAC quiet time setting.
>
> v2:
>
> * use ATH10K_FW_IE_WMI_OP_VERSION instead of a feature flag
>
> * add separate wmi mappings for 10.2.4
>
> * bump up FW API to 4
>
> * new patch: ath10k: set max_num_vdevs based on wmi op version
>
> * new patch: ath10k: use wmi op version to check which iface
> combination to use
>
> * new patch: ath10k: print ath10k wmi op version
>
> ---
>
> Kalle Valo (3):
> ath10k: set max_num_vdevs based on wmi op version
> ath10k: use wmi op version to check which iface combination to use
> ath10k: print ath10k wmi op version
>
> Rajkumar Manoharan (5):
> ath10k: add 10.2.4 firmware support
> ath10k: add wmi support for pdev_set_quiet_mode
> ath10k: add thermal cooling device support
> ath10k: add wmi interface for pdev_get_temperature
> ath10k: add thermal sensor device support
All eight patches applied, thanks Rajkumar.
--
Kalle Valo
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next prev parent reply other threads:[~2014-12-23 15:21 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-12-17 10:20 [PATCH v2 0/8] ath10k: Add thermal mitigation support Kalle Valo
2014-12-17 10:20 ` Kalle Valo
2014-12-17 10:20 ` [PATCH v2 1/8] ath10k: set max_num_vdevs based on wmi op version Kalle Valo
2014-12-17 10:20 ` Kalle Valo
2014-12-17 10:20 ` [PATCH v2 2/8] ath10k: use wmi op version to check which iface combination to use Kalle Valo
2014-12-17 10:20 ` Kalle Valo
2014-12-17 10:21 ` [PATCH v2 3/8] ath10k: print ath10k wmi op version Kalle Valo
2014-12-17 10:21 ` Kalle Valo
2014-12-17 10:21 ` [PATCH v2 4/8] ath10k: add 10.2.4 firmware support Kalle Valo
2014-12-17 10:21 ` Kalle Valo
2014-12-17 10:21 ` [PATCH v2 5/8] ath10k: add wmi support for pdev_set_quiet_mode Kalle Valo
2014-12-17 10:21 ` Kalle Valo
2014-12-17 10:22 ` [PATCH v2 6/8] ath10k: add thermal cooling device support Kalle Valo
2014-12-17 10:22 ` Kalle Valo
2014-12-17 10:22 ` [PATCH v2 7/8] ath10k: add wmi interface for pdev_get_temperature Kalle Valo
2014-12-17 10:22 ` Kalle Valo
2014-12-17 10:22 ` [PATCH v2 8/8] ath10k: add thermal sensor device support Kalle Valo
2014-12-17 10:22 ` Kalle Valo
2014-12-17 18:56 ` Sebastian Gottschall
[not found] ` <5491D20F.2020202@dd-wrt.com>
2014-12-23 17:43 ` Kalle Valo
2014-12-23 17:43 ` Kalle Valo
2014-12-23 19:52 ` Sebastian Gottschall
2014-12-23 19:52 ` Sebastian Gottschall
2014-12-23 15:21 ` Kalle Valo [this message]
2014-12-23 15:21 ` [PATCH v2 0/8] ath10k: Add thermal mitigation support Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87k31ie6ic.fsf@kamboji.qca.qualcomm.com \
--to=kvalo@qca.qualcomm.com \
--cc=ath10k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.