[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[andrej at inversepath.com]

From: Andrej Rosano <andrej@inversepath.com>

Hello,

this series adds support for USB armory board. The patches are
prepared against imx tree as it uses the new arch/board approach.

The first patch add introduces the arch/board approach for mx5,
as already done for mx6.

The second patch adds basic support for USB armory board and
is an updated version (v4) with the modifications described bellow.

Best Regards,
Andrej

Changes for v4:
 - Remove ifdef for CONFIG_FSL_ESDHC as it must always be present
 - Remove explicit GPIO input setup (all GPIO are input after reset)
 - Remove dummy board_late_init() and CONFIG_BOARD_LATE_INIT
 - Remove CONFIG_BOOTARGS
 - Fix compiling errors due to config_distro_bootcmd.h inclusion position

Changes for v3:
 - Add config_distro support

Changes for v2:
 - Fix double print_cpuinfo() call
 - Fix CONFIG_BOOTCOMMAND typo
 - Fix CONFIG_SYS_FSL_ESDHC_NUM to 1

Andrej Rosano (2):
  ARM: mx5: move to a standard arch/board approach
  ARM: mx5: add support for USB armory board


Andrej Rosano (2):
  ARM: mx5: move to a standard arch/board approach
  ARM: mx5: add support for USB armory board

 arch/arm/Kconfig                         |    6 +
 arch/arm/cpu/armv7/mx5/Kconfig           |   27 ++
 board/inversepath/usbarmory/Kconfig      |   15 ++
 board/inversepath/usbarmory/MAINTAINERS  |    6 +
 board/inversepath/usbarmory/Makefile     |   10 +
 board/inversepath/usbarmory/imximage.cfg |   82 ++++++
 board/inversepath/usbarmory/usbarmory.c  |  419 ++++++++++++++++++++++++++++++
 configs/usbarmory_defconfig              |    3 +
 include/configs/usbarmory.h              |  126 +++++++++
 9 files changed, 694 insertions(+)
 create mode 100644 arch/arm/cpu/armv7/mx5/Kconfig
 create mode 100644 board/inversepath/usbarmory/Kconfig
 create mode 100644 board/inversepath/usbarmory/MAINTAINERS
 create mode 100644 board/inversepath/usbarmory/Makefile
 create mode 100644 board/inversepath/usbarmory/imximage.cfg
 create mode 100644 board/inversepath/usbarmory/usbarmory.c
 create mode 100644 configs/usbarmory_defconfig
 create mode 100644 include/configs/usbarmory.h

-- 
1.7.10.4

[U-Boot] [PATCH v4 1/2] ARM: mx5: move to a standard arch/board approach

[andrej at inversepath.com]

From: Andrej Rosano <andrej@inversepath.com>

Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the
commit: 89ebc82137bebb11a8191f8b9cbf08f2533ae8bc

Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
---
 arch/arm/Kconfig               |    6 ++++++
 arch/arm/cpu/armv7/mx5/Kconfig |   16 ++++++++++++++++
 2 files changed, 22 insertions(+)
 create mode 100644 arch/arm/cpu/armv7/mx5/Kconfig

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c0a0fd8..06b8e58 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -437,6 +437,10 @@ config ARCH_MX6
 	bool "Freescale MX6"
 	select CPU_V7
 
+config ARCH_MX5
+	bool "Freescale MX5"
+	select CPU_V7
+
 config TARGET_M53EVK
 	bool "Support m53evk"
 	select CPU_V7
@@ -741,6 +745,8 @@ source "arch/arm/mach-kirkwood/Kconfig"
 
 source "arch/arm/cpu/armv7/mx6/Kconfig"
 
+source "arch/arm/cpu/armv7/mx5/Kconfig"
+
 source "arch/arm/mach-nomadik/Kconfig"
 
 source "arch/arm/cpu/armv7/omap3/Kconfig"
diff --git a/arch/arm/cpu/armv7/mx5/Kconfig b/arch/arm/cpu/armv7/mx5/Kconfig
new file mode 100644
index 0000000..960a718
--- /dev/null
+++ b/arch/arm/cpu/armv7/mx5/Kconfig
@@ -0,0 +1,16 @@
+if ARCH_MX5
+
+config MX5
+	bool
+	default y
+
+config MX51
+	bool
+
+config MX53
+	bool
+
+config SYS_SOC
+	default "mx5"
+
+endif
-- 
1.7.10.4

[U-Boot] [PATCH v4 2/2] ARM: mx5: add support for USB armory board

[andrej at inversepath.com]

From: Andrej Rosano <andrej@inversepath.com>

Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on Freescale i.MX53 SoC.

http://inversepath.com/usbarmory

Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
---
 arch/arm/cpu/armv7/mx5/Kconfig           |   11 +
 board/inversepath/usbarmory/Kconfig      |   15 ++
 board/inversepath/usbarmory/MAINTAINERS  |    6 +
 board/inversepath/usbarmory/Makefile     |   10 +
 board/inversepath/usbarmory/imximage.cfg |   82 ++++++
 board/inversepath/usbarmory/usbarmory.c  |  419 ++++++++++++++++++++++++++++++
 configs/usbarmory_defconfig              |    3 +
 include/configs/usbarmory.h              |  126 +++++++++
 8 files changed, 672 insertions(+)
 create mode 100644 board/inversepath/usbarmory/Kconfig
 create mode 100644 board/inversepath/usbarmory/MAINTAINERS
 create mode 100644 board/inversepath/usbarmory/Makefile
 create mode 100644 board/inversepath/usbarmory/imximage.cfg
 create mode 100644 board/inversepath/usbarmory/usbarmory.c
 create mode 100644 configs/usbarmory_defconfig
 create mode 100644 include/configs/usbarmory.h

diff --git a/arch/arm/cpu/armv7/mx5/Kconfig b/arch/arm/cpu/armv7/mx5/Kconfig
index 960a718..2d6c0ce 100644
--- a/arch/arm/cpu/armv7/mx5/Kconfig
+++ b/arch/arm/cpu/armv7/mx5/Kconfig
@@ -10,7 +10,18 @@ config MX51
 config MX53
 	bool
 
+choice
+	prompt "MX5 board select"
+
+config TARGET_USBARMORY
+	bool "Support USB armory"
+	select CPU_V7
+
+endchoice
+
 config SYS_SOC
 	default "mx5"
 
+source "board/inversepath/usbarmory/Kconfig"
+
 endif
diff --git a/board/inversepath/usbarmory/Kconfig b/board/inversepath/usbarmory/Kconfig
new file mode 100644
index 0000000..c2cd544
--- /dev/null
+++ b/board/inversepath/usbarmory/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_USBARMORY
+
+config IMX_CONFIG
+	default "board/inversepath/usbarmory/imximage.cfg"
+
+config SYS_BOARD
+	default "usbarmory"
+
+config SYS_VENDOR
+	default "inversepath"
+
+config SYS_CONFIG_NAME
+	default "usbarmory"
+
+endif
diff --git a/board/inversepath/usbarmory/MAINTAINERS b/board/inversepath/usbarmory/MAINTAINERS
new file mode 100644
index 0000000..71a3dd4
--- /dev/null
+++ b/board/inversepath/usbarmory/MAINTAINERS
@@ -0,0 +1,6 @@
+USBARMORY BOARD
+M:	Andrej Rosano <andrej@inversepath.com>
+S:	Maintained
+F:	board/inversepath/usbarmory/
+F:	include/configs/usbarmory.h
+F:	configs/usbarmory_defconfig
diff --git a/board/inversepath/usbarmory/Makefile b/board/inversepath/usbarmory/Makefile
new file mode 100644
index 0000000..9b8bd80
--- /dev/null
+++ b/board/inversepath/usbarmory/Makefile
@@ -0,0 +1,10 @@
+#
+# USB armory MkI board Makefile
+# http://inversepath.com/usbarmory
+#
+# Copyright (C) 2015, Inverse Path
+# Andrej Rosano <andrej@inversepath.com>
+#
+# SPDX-License-Identifier:|____GPL-2.0+
+
+obj-y	:= usbarmory.o
diff --git a/board/inversepath/usbarmory/imximage.cfg b/board/inversepath/usbarmory/imximage.cfg
new file mode 100644
index 0000000..392d2f9
--- /dev/null
+++ b/board/inversepath/usbarmory/imximage.cfg
@@ -0,0 +1,82 @@
+/*
+ * USB armory MkI board imximage configuration
+ * http://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * SPDX-License-Identifier:|____GPL-2.0+
+ */
+
+IMAGE_VERSION 2
+BOOT_FROM sd
+
+
+/* IOMUX */
+
+DATA 4 0x53fa86f4 0x00000000 /* GRP_DDRMODE_CTL */
+DATA 4 0x53fa8714 0x00000000 /* GRP_DDRMODE     */
+DATA 4 0x53fa86fc 0x00000000 /* GRP_DDRPKE      */
+DATA 4 0x53fa8724 0x04000000 /* GRP_DDR_TYPE    */
+
+DATA 4 0x53fa872c 0x00300000 /* GRP_B3DS   */
+DATA 4 0x53fa8554 0x00300000 /* DRAM_DQM3  */
+DATA 4 0x53fa8558 0x00300040 /* DRAM_SDQS3 */
+
+DATA 4 0x53fa8728 0x00300000 /* GRP_B2DS   */
+DATA 4 0x53fa8560 0x00300000 /* DRAM_DQM2  */
+DATA 4 0x53fa8568 0x00300040 /* DRAM_SDQS2 */
+
+DATA 4 0x53fa871c 0x00300000 /* GRP_B1DS   */
+DATA 4 0x53fa8594 0x00300000 /* DRAM_DQM1  */
+DATA 4 0x53fa8590 0x00300040 /* DRAM_SDQS1 */
+
+DATA 4 0x53fa8718 0x00300000 /* GRP_B0DS   */
+DATA 4 0x53fa8584 0x00300000 /* DRAM_DQM0  */
+DATA 4 0x53fa857c 0x00300040 /* DRAM_SDQS0 */
+
+DATA 4 0x53fa8578 0x00300000 /* DRAM_SDCLK0 */
+DATA 4 0x53fa8570 0x00300000 /* DRAM_SDCLK1 */
+
+DATA 4 0x53fa8574 0x00300000 /* DRAM_CAS  */
+DATA 4 0x53fa8588 0x00300000 /* DRAM_RAS  */
+DATA 4 0x53fa86f0 0x00300000 /* GRP_ADDS  */
+DATA 4 0x53fa8720 0x00300000 /* GRP_CTLDS */
+
+DATA 4 0x53fa8564 0x00300040 /* DRAM_SDODT1 */
+DATA 4 0x53fa8580 0x00300040 /* DRAM_SDODT0 */
+
+
+/* ESDCTL */
+
+DATA 4 0x63fd9000 0x84180000 /* ESDCTL_ESDCTL  */
+
+DATA 4 0x63fd9004 0x0002002d /* ESDCTL_ESDPTC  */
+DATA 4 0x63fd9008 0x12273030 /* ESDCTL_ESDOTC  */
+DATA 4 0x63fd900c 0x9f5152e3 /* ESDCTL_ESDCFG0 */
+DATA 4 0x63fd9010 0xb68e8a63 /* ESDCTL_ESDCFG1 */
+DATA 4 0x63fd9014 0x01ff00db /* ESDCTL_ESDCFG2 */
+DATA 4 0x63fd9018 0x00011740 /* ESDCTL_ESDMISC */
+
+DATA 4 0x63fd901c 0x00008032 /* ESDCTL_ESDSCR  */
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00028031
+DATA 4 0x63fd901c 0x052080b0
+DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd901c 0x0000803a
+DATA 4 0x63fd901c 0x0000803b
+DATA 4 0x63fd901c 0x00028039
+DATA 4 0x63fd901c 0x05208138
+DATA 4 0x63fd901c 0x04008048
+DATA 4 0x63fd901c 0x00000000
+
+DATA 4 0x63fd9020 0x00005800 /* ESDCTL_ESDREF   */
+DATA 4 0x63fd902c 0x000026d2 /* ESDCTL_ESDEWD   */
+DATA 4 0x63fd9030 0x009f0e21 /* ESDCTL_ESDOR    */
+DATA 4 0x63fd9040 0x05380003 /* ESDCTL_ZQHWCTRL */
+DATA 4 0x63fd9058 0x00022227 /* ESDCTL_ODTCTRL  */
+
+DATA 4 0x63fd907c 0x01370138 /* ESDCTL_DGCTRL0  */
+DATA 4 0x63fd9080 0x013b013c /* ESDCTL_DGCTRL1  */
+DATA 4 0x63fd9088 0x35343535 /* ESDCTL_RDDLCTL  */
+DATA 4 0x63fd9090 0x4d444c44 /* ESDCTL_WRDLCTL  */
diff --git a/board/inversepath/usbarmory/usbarmory.c b/board/inversepath/usbarmory/usbarmory.c
new file mode 100644
index 0000000..3e60a86
--- /dev/null
+++ b/board/inversepath/usbarmory/usbarmory.c
@@ -0,0 +1,419 @@
+/*
+ * USB armory MkI board initialization
+ * http://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux-mx53.h>
+#include <asm/errno.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+u32 get_board_rev(void)
+{
+	struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
+	struct fuse_bank *bank = &iim->bank[0];
+	struct fuse_bank0_regs *fuse =
+		(struct fuse_bank0_regs *)bank->fuse_regs;
+
+	int rev = readl(&fuse->gp[6]);
+
+	return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
+}
+
+struct fsl_esdhc_cfg esdhc_cfg[1] = {
+	{MMC_SDHC1_BASE_ADDR}
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	/* CD not present */
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret = 0;
+
+	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+	ret = fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
+
+	return ret;
+}
+
+#define SD_CMD_PAD_CTRL	(PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+			PAD_CTL_PUS_100K_UP)
+#define I2C_PAD_CTRL	(PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
+			PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+#define PAD_CTRL_UP	PAD_CTL_PUS_100K_UP
+#define PAD_CTRL_GND	PAD_CTL_PUS_100K_DOWN
+
+static void setup_iomux_sd(void)
+{
+	static const iomux_v3_cfg_t pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, MX53_SDHC_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0,
+			MX53_SDHC_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1,
+			MX53_SDHC_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2,
+			MX53_SDHC_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3,
+			MX53_SDHC_PAD_CTRL),
+		MX53_PAD_EIM_DA13__GPIO3_13,
+	};
+
+	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
+}
+
+static void setup_iomux_led(void)
+{
+	static const iomux_v3_cfg_t pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT6__GPIO4_27,
+			PAD_CTL_PUS_100K_DOWN),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
+}
+
+static void setup_iomux_i2c(void)
+{
+	static const iomux_v3_cfg_t pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_EIM_D28__I2C1_SDA, I2C_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D21__I2C1_SCL, I2C_PAD_CTRL),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
+}
+
+static void setup_iomux_pinheader(void)
+{
+	static const iomux_v3_cfg_t pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__GPIO5_26, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__GPIO5_27, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX,
+			MX53_UART_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX,
+			MX53_UART_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT12__GPIO5_30, PAD_CTRL_UP),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
+}
+
+static void setup_iomux_unused_boot(void)
+{
+	static const iomux_v3_cfg_t pads[] = {
+
+		/* Pulled-up pads */
+		NEW_PAD_CTRL(MX53_PAD_EIM_A21__GPIO2_17, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA0__GPIO3_0, PAD_CTRL_UP),
+
+		/* Grounded pads */
+		NEW_PAD_CTRL(MX53_PAD_EIM_LBA__GPIO2_27, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_EB0__GPIO2_28, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_EB1__GPIO2_29, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A16__GPIO2_22, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A17__GPIO2_21, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A18__GPIO2_20, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A19__GPIO2_19, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A20__GPIO2_18, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A22__GPIO2_16, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA1__GPIO3_1, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA2__GPIO3_2, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA3__GPIO3_3, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA4__GPIO3_4, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA5__GPIO3_5, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA6__GPIO3_6, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA7__GPIO3_7, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA8__GPIO3_8, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA9__GPIO3_9, PAD_CTRL_GND),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA10__GPIO3_10, PAD_CTRL_GND),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
+}
+
+static void setup_iomux_unused_nc(void)
+{
+	/* Out of reset values define the pin values before the
+	   ROM is executed so we force all the not connected pins
+	   to a known state */
+	static const iomux_v3_cfg_t pads[] = {
+
+		/* CONTROL PINS block */
+		NEW_PAD_CTRL(MX53_PAD_GPIO_0__GPIO1_0, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_1__GPIO1_1, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_2__GPIO1_2, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_3__GPIO1_3, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_4__GPIO1_4, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_5__GPIO1_5, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_6__GPIO1_6, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_7__GPIO1_7, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_8__GPIO1_8, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_9__GPIO1_9, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_10__GPIO4_0, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_11__GPIO4_1, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_12__GPIO4_2, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_13__GPIO4_3, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_14__GPIO4_4, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_16__GPIO7_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_17__GPIO7_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_18__GPIO7_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_GPIO_19__GPIO4_5, PAD_CTRL_UP),
+
+		/* EIM block */
+		NEW_PAD_CTRL(MX53_PAD_EIM_OE__GPIO2_25, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_WAIT__GPIO5_0, PAD_CTRL_UP),
+		/* EIM_LBA: setup_iomux_unused_boot() */
+		NEW_PAD_CTRL(MX53_PAD_EIM_RW__GPIO2_26, PAD_CTRL_UP),
+		/* EIM_EB0: setup_iomux_unused_boot() */
+		/* EIM_EB1: setup_iomux_unused_boot() */
+		NEW_PAD_CTRL(MX53_PAD_EIM_EB2__GPIO2_30, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_EB3__GPIO2_31, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_CS0__GPIO2_23, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_CS1__GPIO2_24, PAD_CTRL_UP),
+		/* EIM_A16: setup_iomux_unused_boot() */
+		/* EIM_A17: setup_iomux_unused_boot() */
+		/* EIM_A18: setup_iomux_unused_boot() */
+		/* EIM_A19: setup_iomux_unused_boot() */
+		/* EIM_A20: setup_iomux_unused_boot() */
+		/* EIM_A21: setup_iomux_unused_boot() */
+		/* EIM_A22: setup_iomux_unused_boot() */
+		NEW_PAD_CTRL(MX53_PAD_EIM_A23__GPIO6_6, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A24__GPIO5_4, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_A25__GPIO5_2, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D16__GPIO3_16, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D17__GPIO3_17, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D18__GPIO3_18, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D19__GPIO3_19, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D20__GPIO3_20, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D21__GPIO3_21, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D22__GPIO3_22, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D23__GPIO3_23, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D24__GPIO3_24, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D25__GPIO3_25, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D26__GPIO3_26, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D27__GPIO3_27, PAD_CTRL_UP),
+		/* EIM_D28: setup_iomux_unused_boot() */
+		/* EIM_D29: setup_iomux_unused_boot() */
+		NEW_PAD_CTRL(MX53_PAD_EIM_D30__GPIO3_30, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_D31__GPIO3_31, PAD_CTRL_UP),
+		/* EIM_DA0: setup_iomux_unused_boot() */
+		/* EIM_DA1: setup_iomux_unused_boot() */
+		/* EIM_DA2: setup_iomux_unused_boot() */
+		/* EIM_DA3: setup_iomux_unused_boot() */
+		/* EIM_DA4: setup_iomux_unused_boot() */
+		/* EIM_DA5: setup_iomux_unused_boot() */
+		/* EIM_DA6: setup_iomux_unused_boot() */
+		/* EIM_DA7: setup_iomux_unused_boot() */
+		/* EIM_DA8: setup_iomux_unused_boot() */
+		/* EIM_DA9: setup_iomux_unused_boot() */
+		/* EIM_DA10: setup_iomux_unused_boot() */
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA11__GPIO3_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA12__GPIO3_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA13__GPIO3_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA14__GPIO3_14, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_EIM_DA15__GPIO3_15, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_WE_B__GPIO6_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_RE_B__GPIO6_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_ALE__GPIO6_8, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_CLE__GPIO6_7, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_WP_B__GPIO6_9, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_RB0__GPIO6_10, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_CS0__GPIO6_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_CS1__GPIO6_14, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_CS2__GPIO6_15, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_NANDF_CS3__GPIO6_16, PAD_CTRL_UP),
+
+		/* MISC block */
+		NEW_PAD_CTRL(MX53_PAD_FEC_MDC__GPIO1_31, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__GPIO1_22, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__GPIO1_25, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__GPIO1_23, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__GPIO1_24, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__GPIO1_28, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__GPIO1_27, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__GPIO1_26, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__GPIO1_30, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__GPIO1_29, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_COL0__GPIO4_6, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_ROW0__GPIO4_7, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_COL1__GPIO4_8, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_ROW1__GPIO4_9, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_COL2__GPIO4_10, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_ROW2__GPIO4_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_COL3__GPIO4_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_ROW3__GPIO4_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_COL4__GPIO4_14, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_KEY_ROW4__GPIO4_15, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_SD2_CMD__GPIO1_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_SD2_CLK__GPIO1_10, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_SD2_DATA0__GPIO1_15, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_SD2_DATA1__GPIO1_14, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_SD2_DATA2__GPIO1_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_SD2_DATA3__GPIO1_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_BUFFER_EN__GPIO7_1, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_CS_0__GPIO7_9, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_CS_1__GPIO7_10, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DA_0__GPIO7_6, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DA_1__GPIO7_7, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DA_2__GPIO7_8, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__GPIO2_0, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__GPIO2_1, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__GPIO2_2, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__GPIO2_3, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA4__GPIO2_4, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA5__GPIO2_5, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA6__GPIO2_6, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA7__GPIO2_7, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__GPIO2_8, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__GPIO2_9, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__GPIO2_10, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__GPIO2_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA12__GPIO2_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA13__GPIO2_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA14__GPIO2_14, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA15__GPIO2_15, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DIOR__GPIO7_3, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DIOW__GPIO6_17, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DMACK__GPIO6_18, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DMARQ__GPIO7_0, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_INTRQ__GPIO7_2, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__GPIO7_5, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__GPIO7_4, PAD_CTRL_UP),
+
+		/* IPU block */
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT4__GPIO5_22, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT5__GPIO5_23, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT6__GPIO5_24, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT7__GPIO5_25, PAD_CTRL_UP),
+		/* CSI0_DAT8: setup_iomux_pinheader() */
+		/* CSI0_DAT9: setup_iomux_pinheader() */
+		/* CSI0_DAT10: setup_iomux_pinheader() */
+		/* CSI0_DAT11: setup_iomux_pinheader() */
+		/* CSI0_DAT12: setup_iomux_pinheader() */
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT13__GPIO5_31, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT14__GPIO6_0, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT15__GPIO6_1, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT16__GPIO6_2, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT17__GPIO6_3, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT18__GPIO6_4, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT19__GPIO6_5, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_VSYNC__GPIO5_21, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_PIXCLK__GPIO5_18, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_MCLK__GPIO5_19, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DATA_EN__GPIO5_20, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DI0_PIN2__GPIO4_18, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DI0_PIN3__GPIO4_19, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DI0_PIN4__GPIO4_20, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DI0_PIN15__GPIO4_17, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT0__GPIO4_21, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT1__GPIO4_22, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT2__GPIO4_23, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT3__GPIO4_24, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT4__GPIO4_25, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT5__GPIO4_26, PAD_CTRL_UP),
+		/* DISP0_DAT6: setup_iomux_led() */
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT7__GPIO4_28, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT8__GPIO4_29, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT9__GPIO4_30, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT10__GPIO4_31, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT11__GPIO5_5, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT12__GPIO5_6, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT13__GPIO5_7, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT14__GPIO5_8, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT15__GPIO5_9, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT16__GPIO5_10, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT17__GPIO5_11, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT18__GPIO5_12, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT19__GPIO5_13, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT20__GPIO5_14, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT21__GPIO5_15, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT22__GPIO5_16, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT23__GPIO5_17, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_DI0_DISP_CLK__GPIO4_16, PAD_CTRL_UP),
+
+		/* LVDS block */
+		NEW_PAD_CTRL(MX53_PAD_LVDS0_TX0_P__GPIO7_30, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS0_TX1_P__GPIO7_28, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS0_TX2_P__GPIO7_26, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS0_TX3_P__GPIO7_22, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS1_TX0_P__GPIO6_30, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS1_TX1_P__GPIO6_28, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS1_TX2_P__GPIO6_24, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS1_TX3_P__GPIO6_22, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS0_CLK_P__GPIO7_24, PAD_CTRL_UP),
+		NEW_PAD_CTRL(MX53_PAD_LVDS1_CLK_P__GPIO6_26, PAD_CTRL_UP),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
+}
+
+#define CPU_CLOCK 800
+
+static void set_clock(void)
+{
+	u32 ref_clk = MXC_HCLK;
+	const uint32_t cpuclk = CPU_CLOCK;
+	const uint32_t dramclk = 400;
+	int ret;
+
+	ret = mxc_set_clock(ref_clk, cpuclk, MXC_ARM_CLK);
+	if (ret)
+		printf("CPU:   Switch CPU clock to %dMHZ failed\n", cpuclk);
+
+	ret = mxc_set_clock(ref_clk, dramclk, MXC_PERIPH_CLK);
+	if (ret)
+		printf("CPU:   Switch peripheral clock to %dMHz failed\n",
+		    dramclk);
+
+	ret = mxc_set_clock(ref_clk, dramclk, MXC_DDR_CLK);
+	if (ret)
+		printf("CPU:   Switch DDR clock to %dMHz failed\n", dramclk);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_unused_nc();
+	setup_iomux_unused_boot();
+	setup_iomux_sd();
+	setup_iomux_led();
+	setup_iomux_pinheader();
+	set_clock();
+	return 0;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+	setup_iomux_i2c();
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 1 << 30);
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Inverse Path USB armory MkI\n");
+	return 0;
+}
diff --git a/configs/usbarmory_defconfig b/configs/usbarmory_defconfig
new file mode 100644
index 0000000..10bdd9e
--- /dev/null
+++ b/configs/usbarmory_defconfig
@@ -0,0 +1,3 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX5=y
+CONFIG_TARGET_USBARMORY=y
diff --git a/include/configs/usbarmory.h b/include/configs/usbarmory.h
new file mode 100644
index 0000000..60d7091
--- /dev/null
+++ b/include/configs/usbarmory.h
@@ -0,0 +1,126 @@
+/*
+ * USB armory MkI board configuration settings
+ * http://inversepath.com/usbarmory
+ *
+ * Copyright (C) 2015, Inverse Path
+ * Andrej Rosano <andrej@inversepath.com>
+ *
+ * SPDX-License-Identifier:|____GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MX53
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_OF_LIBFDT
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_MXC_GPIO
+
+#include <asm/arch/imx-regs.h>
+#include <config_cmd_default.h>
+
+#include <config_distro_defaults.h>
+
+/* U-Boot commands */
+#define CONFIG_CMD_MEMTEST
+#undef CONFIG_CMD_IMLS
+
+/* U-Boot environment */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_OFFSET	(6 * 64 * 1024)
+#define CONFIG_ENV_SIZE		(8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV	0
+
+/* U-Boot general configurations */
+#define CONFIG_SYS_CBSIZE	512
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS	16
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+/* UART */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_BAUDRATE		115200
+
+/* SD/MMC */
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_ESDHC_NUM	1
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+
+/* USB */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX5
+#define CONFIG_USB_STORAGE
+#define CONFIG_MXC_USB_PORT	1
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+
+/* Fuse */
+#define CONFIG_CMD_FUSE
+#define CONFIG_FSL_IIM
+
+/* Linux boot */
+#define CONFIG_LOADADDR		0x72000000
+#define CONFIG_SYS_TEXT_BASE	0x77800000
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+#define CONFIG_HOSTNAME		usbarmory
+#define CONFIG_BOOTCOMMAND						\
+	"run distro_bootcmd; "						\
+	"setenv bootargs console=${console} ${bootargs_default}; "	\
+	"ext2load mmc 0:1 ${kernel_addr_r} /boot/uImage; "		\
+	"ext2load mmc 0:1 ${fdt_addr_r} /boot/${fdtfile}; "		\
+	"bootm ${kernel_addr_r} - ${fdt_addr_r}"
+
+#define BOOT_TARGET_DEVICES(func) func(MMC, mmc, 0)
+
+#include <config_distro_bootcmd.h>
+
+#define MEM_LAYOUT_ENV_SETTINGS			\
+	"kernel_addr_r=0x70800000\0"		\
+	"fdt_addr_r=0x71000000\0"		\
+	"scriptaddr=0x70800000\0"		\
+	"pxefile_addr_r=0x70800000\0"		\
+	"ramdisk_addr_r=0x73000000\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS				\
+	MEM_LAYOUT_ENV_SETTINGS					\
+	"bootargs_default=root=/dev/mmcblk0p1 rootwait rw\0"	\
+	"fdtfile=imx53-usbarmory.dtb\0"				\
+	"console=ttymxc0,115200\0"				\
+	BOOTENV
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			CSD0_BASE_ADDR
+#define PHYS_SDRAM_SIZE			(gd->ram_size)
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_MEMTEST_START	0x70000000
+#define CONFIG_SYS_MEMTEST_END		0x90000000
+
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
+
+#endif				/* __CONFIG_H */
-- 
1.7.10.4

[U-Boot] [PATCH v4 2/2] ARM: mx5: add support for USB armory board

[Vagrant Cascadian]

On 2015-03-26, andrej at inversepath.com wrote:
> From: Andrej Rosano <andrej@inversepath.com>
>
> Add support for Inverse Path USB armory board, an open source
> flash-drive sized computer based on Freescale i.MX53 SoC.
>
> http://inversepath.com/usbarmory

Tested-By: Vagrant Cascadian <vagrant@debian.org>


live well,
  vagrant
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 818 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150326/b4d29267/attachment.sig>

[U-Boot] [PATCH v4 1/2] ARM: mx5: move to a standard arch/board approach

[Chris Kuethe]

On Thu, Mar 26, 2015 at 4:49 AM, <andrej@inversepath.com> wrote:
>
> From: Andrej Rosano <andrej@inversepath.com>
>
> Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the
> commit: 89ebc82137bebb11a8191f8b9cbf08f2533ae8bc
>
> Signed-off-by: Andrej Rosano <andrej@inversepath.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Vagrant Cascadian <vagrant@debian.org>

Tested-by: Chris Kuethe <chris.kuethe@gmail.com>


-- 
GDB has a 'break' feature; why doesn't it have 'fix' too?

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Chris Kuethe]

On Thu, Mar 26, 2015 at 4:49 AM,  <andrej@inversepath.com> wrote:
> From: Andrej Rosano <andrej@inversepath.com>
>
> Hello,
>
> this series adds support for USB armory board. The patches are
> prepared against imx tree as it uses the new arch/board approach.
>
> The first patch add introduces the arch/board approach for mx5,
> as already done for mx6.

Yep, that works.

> The second patch adds basic support for USB armory board and
> is an updated version (v4) with the modifications described bellow.

If I test this against HEAD as of
f643d9294f45487f22e8f33d6572530f17eff4e9, I get an error reated to
IMX_CONFIG.

"board/inversepath/usbarmory/Kconfig:3:warning: config symbol defined
without type"

Here's a diff to fix that

diff --git a/board/inversepath/usbarmory/Kconfig
b/board/inversepath/usbarmory/Kconfig
index c2cd544..4776b1d 100644
--- a/board/inversepath/usbarmory/Kconfig
+++ b/board/inversepath/usbarmory/Kconfig
@@ -1,8 +1,5 @@
 if TARGET_USBARMORY

-config IMX_CONFIG
-    default "board/inversepath/usbarmory/imximage.cfg"
-
 config SYS_BOARD
     default "usbarmory"

diff --git a/configs/usbarmory_defconfig b/configs/usbarmory_defconfig
index 10bdd9e..237b1ca 100644
--- a/configs/usbarmory_defconfig
+++ b/configs/usbarmory_defconfig
@@ -1,3 +1,4 @@
 CONFIG_ARM=y
 CONFIG_ARCH_MX5=y
 CONFIG_TARGET_USBARMORY=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/inversepath/usbarmory/imximage.cfg"


> Changes for v4:
>  - Remove ifdef for CONFIG_FSL_ESDHC as it must always be present
>  - Remove explicit GPIO input setup (all GPIO are input after reset)
>  - Remove dummy board_late_init() and CONFIG_BOARD_LATE_INIT
>  - Remove CONFIG_BOOTARGS
>  - Fix compiling errors due to config_distro_bootcmd.h inclusion position

Tested-by: Chris Kuethe <chris.kuethe@gmail.com>

> Changes for v3:
>  - Add config_distro support
>
> Changes for v2:
>  - Fix double print_cpuinfo() call
>  - Fix CONFIG_BOOTCOMMAND typo
>  - Fix CONFIG_SYS_FSL_ESDHC_NUM to 1
>
> Andrej Rosano (2):
>   ARM: mx5: move to a standard arch/board approach
>   ARM: mx5: add support for USB armory board
>
>
> Andrej Rosano (2):
>   ARM: mx5: move to a standard arch/board approach
>   ARM: mx5: add support for USB armory board



-- 
GDB has a 'break' feature; why doesn't it have 'fix' too?

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Andrej Rosano]

Hi Chris,

On Thu, Mar 26, 2015 at 02:53:58PM -0700, Chris Kuethe wrote:
> On Thu, Mar 26, 2015 at 4:49 AM,  <andrej@inversepath.com> wrote:
> > From: Andrej Rosano <andrej@inversepath.com>
> >
> > Hello,
> >
> > this series adds support for USB armory board. The patches are
> > prepared against imx tree as it uses the new arch/board approach.
> >
> > The first patch add introduces the arch/board approach for mx5,
> > as already done for mx6.
> 
> Yep, that works.
> 
> > The second patch adds basic support for USB armory board and
> > is an updated version (v4) with the modifications described bellow.
> 
> If I test this against HEAD as of
> f643d9294f45487f22e8f33d6572530f17eff4e9, I get an error reated to
> IMX_CONFIG.

Please note that the patch is prepared against imx tree and not the
mainline one, where the "arch/board approach" is not yet merged.

Cheers,
Andrej

> 
> "board/inversepath/usbarmory/Kconfig:3:warning: config symbol defined
> without type"
> 
> Here's a diff to fix that
> 
> diff --git a/board/inversepath/usbarmory/Kconfig
> b/board/inversepath/usbarmory/Kconfig
> index c2cd544..4776b1d 100644
> --- a/board/inversepath/usbarmory/Kconfig
> +++ b/board/inversepath/usbarmory/Kconfig
> @@ -1,8 +1,5 @@
>  if TARGET_USBARMORY
> 
> -config IMX_CONFIG
> -    default "board/inversepath/usbarmory/imximage.cfg"
> -
>  config SYS_BOARD
>      default "usbarmory"
> 
> diff --git a/configs/usbarmory_defconfig b/configs/usbarmory_defconfig
> index 10bdd9e..237b1ca 100644
> --- a/configs/usbarmory_defconfig
> +++ b/configs/usbarmory_defconfig
> @@ -1,3 +1,4 @@
>  CONFIG_ARM=y
>  CONFIG_ARCH_MX5=y
>  CONFIG_TARGET_USBARMORY=y
> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/inversepath/usbarmory/imximage.cfg"
> 
> 
> > Changes for v4:
> >  - Remove ifdef for CONFIG_FSL_ESDHC as it must always be present
> >  - Remove explicit GPIO input setup (all GPIO are input after reset)
> >  - Remove dummy board_late_init() and CONFIG_BOARD_LATE_INIT
> >  - Remove CONFIG_BOOTARGS
> >  - Fix compiling errors due to config_distro_bootcmd.h inclusion position
> 
> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
> 
> > Changes for v3:
> >  - Add config_distro support
> >
> > Changes for v2:
> >  - Fix double print_cpuinfo() call
> >  - Fix CONFIG_BOOTCOMMAND typo
> >  - Fix CONFIG_SYS_FSL_ESDHC_NUM to 1
> >
> > Andrej Rosano (2):
> >   ARM: mx5: move to a standard arch/board approach
> >   ARM: mx5: add support for USB armory board
> >
> >
> > Andrej Rosano (2):
> >   ARM: mx5: move to a standard arch/board approach
> >   ARM: mx5: add support for USB armory board
> 
> 
> 
> -- 
> GDB has a 'break' feature; why doesn't it have 'fix' too?

--
Andrej Rosano                                           Inverse Path Srl
<andrej@inversepath.com>                      http://www.inversepath.com

0x01939B21            5BB8 574E 68E8 D841 E18F  D5E9 CEAD E0CF 0193 9B21

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Chris Kuethe]

On Thu, Mar 26, 2015 at 3:23 PM, Andrej Rosano <andrej@inversepath.com> wrote:

> Please note that the patch is prepared against imx tree and not the
> mainline one, where the "arch/board approach" is not yet merged.

OK, it all works for me.


-- 
GDB has a 'break' feature; why doesn't it have 'fix' too?

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Chris Kuethe]

Any chance of this being accepted into 2015.04?

On Thu, Mar 26, 2015 at 3:28 PM, Chris Kuethe <chris.kuethe@gmail.com> wrote:
> On Thu, Mar 26, 2015 at 3:23 PM, Andrej Rosano <andrej@inversepath.com> wrote:
>
>> Please note that the patch is prepared against imx tree and not the
>> mainline one, where the "arch/board approach" is not yet merged.
>
> OK, it all works for me.
>
>
> --
> GDB has a 'break' feature; why doesn't it have 'fix' too?



-- 
GDB has a 'break' feature; why doesn't it have 'fix' too?

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Stefano Babic]

Hi Chris,

On 01/04/2015 04:46, Chris Kuethe wrote:
> Any chance of this being accepted into 2015.04?
> 

It was my intention to put it into the -next branch, ready to be merged
after release. Anyway, if there is still time for a new PR, I will try
to let it slipping in the current. First version of this patch was sent
in February and it is not odd to merge it in 2015.04.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Stefano Babic]

On 01/04/2015 13:32, Stefano Babic wrote:
> Hi Chris,
> 
> On 01/04/2015 04:46, Chris Kuethe wrote:
>> Any chance of this being accepted into 2015.04?
>>
> 

checpatch reports some issues by patch 2/2. Can you please fix them and
resubmit ? Thanks !

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Vagrant Cascadian]

On 2015-04-08, Stefano Babic wrote:
> On 01/04/2015 13:32, Stefano Babic wrote:
>> On 01/04/2015 04:46, Chris Kuethe wrote:
>>> Any chance of this being accepted into 2015.04?
>
> checpatch reports some issues by patch 2/2. Can you please fix them and
> resubmit ? Thanks !

Applying the patch below corrects most of the issues, but not all of the
reported issues:

Cleaned 2 patches
0 errors, 1 warnings, 0 checks for
0001-ARM-mx5-move-to-a-standard-arch-board-approach.patch:
warning: arch/arm/Kconfig,440: please write a paragraph that describes
the config symbol fully

0 errors, 1 warnings, 1 checks for
0002-ARM-mx5-add-support-for-USB-armory-board.patch:
check: board/inversepath/usbarmory/usbarmory.c,382: Alignment should
match open parenthesis
warning: include/configs/usbarmory.h,41: line over 80 characters

checkpatch.pl found 0 error(s), 2 warning(s), 1 checks(s)

diff --git a/board/inversepath/usbarmory/usbarmory.c b/board/inversepath/usbarmory/usbarmory.c
index 3e60a86..573d586 100644
--- a/board/inversepath/usbarmory/usbarmory.c
+++ b/board/inversepath/usbarmory/usbarmory.c
@@ -68,13 +68,13 @@ static void setup_iomux_sd(void)
 		NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, MX53_SDHC_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0,
-			MX53_SDHC_PAD_CTRL),
+			     MX53_SDHC_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1,
-			MX53_SDHC_PAD_CTRL),
+			     MX53_SDHC_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2,
-			MX53_SDHC_PAD_CTRL),
+			     MX53_SDHC_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3,
-			MX53_SDHC_PAD_CTRL),
+			     MX53_SDHC_PAD_CTRL),
 		MX53_PAD_EIM_DA13__GPIO3_13,
 	};
 
@@ -85,7 +85,7 @@ static void setup_iomux_led(void)
 {
 	static const iomux_v3_cfg_t pads[] = {
 		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT6__GPIO4_27,
-			PAD_CTL_PUS_100K_DOWN),
+			     PAD_CTL_PUS_100K_DOWN),
 	};
 
 	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
@@ -107,9 +107,9 @@ static void setup_iomux_pinheader(void)
 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__GPIO5_26, PAD_CTRL_UP),
 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__GPIO5_27, PAD_CTRL_UP),
 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX,
-			MX53_UART_PAD_CTRL),
+			     MX53_UART_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX,
-			MX53_UART_PAD_CTRL),
+			     MX53_UART_PAD_CTRL),
 		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT12__GPIO5_30, PAD_CTRL_UP),
 	};
 
@@ -119,7 +119,6 @@ static void setup_iomux_pinheader(void)
 static void setup_iomux_unused_boot(void)
 {
 	static const iomux_v3_cfg_t pads[] = {
-
 		/* Pulled-up pads */
 		NEW_PAD_CTRL(MX53_PAD_EIM_A21__GPIO2_17, PAD_CTRL_UP),
 		NEW_PAD_CTRL(MX53_PAD_EIM_DA0__GPIO3_0, PAD_CTRL_UP),
@@ -155,7 +154,6 @@ static void setup_iomux_unused_nc(void)
 	   ROM is executed so we force all the not connected pins
 	   to a known state */
 	static const iomux_v3_cfg_t pads[] = {
-
 		/* CONTROL PINS block */
 		NEW_PAD_CTRL(MX53_PAD_GPIO_0__GPIO1_0, PAD_CTRL_UP),
 		NEW_PAD_CTRL(MX53_PAD_GPIO_1__GPIO1_1, PAD_CTRL_UP),


live well,
  vagrant
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 818 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150408/867c50be/attachment.sig>

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Stefano Babic]

Hi,

On 08/04/2015 17:37, Vagrant Cascadian wrote:
> On 2015-04-08, Stefano Babic wrote:
>> On 01/04/2015 13:32, Stefano Babic wrote:
>>> On 01/04/2015 04:46, Chris Kuethe wrote:
>>>> Any chance of this being accepted into 2015.04?
>>
>> checpatch reports some issues by patch 2/2. Can you please fix them and
>> resubmit ? Thanks !
> 
> Applying the patch below corrects most of the issues, but not all of the
> reported issues:
> 
> Cleaned 2 patches
> 0 errors, 1 warnings, 0 checks for
> 0001-ARM-mx5-move-to-a-standard-arch-board-approach.patch:
> warning: arch/arm/Kconfig,440: please write a paragraph that describes
> the config symbol fully
> 

This is not an issue. Patch 1/1 can be applied without changes.

> 0 errors, 1 warnings, 1 checks for
> 0002-ARM-mx5-add-support-for-USB-armory-board.patch:
> check: board/inversepath/usbarmory/usbarmory.c,382: Alignment should
> match open parenthesis
> warning: include/configs/usbarmory.h,41: line over 80 characters
> 

Both of them must be fixed.

> checkpatch.pl found 0 error(s), 2 warning(s), 1 checks(s)
> 
> diff --git a/board/inversepath/usbarmory/usbarmory.c b/board/inversepath/usbarmory/usbarmory.c
> index 3e60a86..573d586 100644
> --- a/board/inversepath/usbarmory/usbarmory.c
> +++ b/board/inversepath/usbarmory/usbarmory.c
> @@ -68,13 +68,13 @@ static void setup_iomux_sd(void)
>  		NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, MX53_SDHC_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0,
> -			MX53_SDHC_PAD_CTRL),
> +			     MX53_SDHC_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1,
> -			MX53_SDHC_PAD_CTRL),
> +			     MX53_SDHC_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2,
> -			MX53_SDHC_PAD_CTRL),
> +			     MX53_SDHC_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3,
> -			MX53_SDHC_PAD_CTRL),
> +			     MX53_SDHC_PAD_CTRL),
>  		MX53_PAD_EIM_DA13__GPIO3_13,
>  	};
>  
> @@ -85,7 +85,7 @@ static void setup_iomux_led(void)
>  {
>  	static const iomux_v3_cfg_t pads[] = {
>  		NEW_PAD_CTRL(MX53_PAD_DISP0_DAT6__GPIO4_27,
> -			PAD_CTL_PUS_100K_DOWN),
> +			     PAD_CTL_PUS_100K_DOWN),
>  	};
>  
>  	imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads));
> @@ -107,9 +107,9 @@ static void setup_iomux_pinheader(void)
>  		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__GPIO5_26, PAD_CTRL_UP),
>  		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__GPIO5_27, PAD_CTRL_UP),
>  		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX,
> -			MX53_UART_PAD_CTRL),
> +			     MX53_UART_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX,
> -			MX53_UART_PAD_CTRL),
> +			     MX53_UART_PAD_CTRL),
>  		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT12__GPIO5_30, PAD_CTRL_UP),
>  	};
>  
> @@ -119,7 +119,6 @@ static void setup_iomux_pinheader(void)
>  static void setup_iomux_unused_boot(void)
>  {
>  	static const iomux_v3_cfg_t pads[] = {
> -
>  		/* Pulled-up pads */
>  		NEW_PAD_CTRL(MX53_PAD_EIM_A21__GPIO2_17, PAD_CTRL_UP),
>  		NEW_PAD_CTRL(MX53_PAD_EIM_DA0__GPIO3_0, PAD_CTRL_UP),
> @@ -155,7 +154,6 @@ static void setup_iomux_unused_nc(void)
>  	   ROM is executed so we force all the not connected pins
>  	   to a known state */
>  	static const iomux_v3_cfg_t pads[] = {
> -
>  		/* CONTROL PINS block */
>  		NEW_PAD_CTRL(MX53_PAD_GPIO_0__GPIO1_0, PAD_CTRL_UP),
>  		NEW_PAD_CTRL(MX53_PAD_GPIO_1__GPIO1_1, PAD_CTRL_UP),
> 
> 

Ok, but I need that the patch is sent again (no following up patch) with
git send-email to avoid issues with the mailer.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Andrej Rosano]

Hi Stefano,

On Wed, Apr 08, 2015 at 10:53:02AM +0200, Stefano Babic wrote:
> On 01/04/2015 13:32, Stefano Babic wrote:
> > Hi Chris,
> > 
> > On 01/04/2015 04:46, Chris Kuethe wrote:
> >> Any chance of this being accepted into 2015.04?
> >>
> > 
> 
> checpatch reports some issues by patch 2/2. Can you please fix them and
> resubmit ? Thanks !

Just resubmitted the v5 version.

Thanks,
Andrej

> 
> Best regards,
> Stefano Babic
> 
> 
> -- 
> =====================================================================
> DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> =====================================================================
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot

--
Andrej Rosano                                           Inverse Path Srl
<andrej@inversepath.com>                      http://www.inversepath.com

0x01939B21            5BB8 574E 68E8 D841 E18F  D5E9 CEAD E0CF 0193 9B21

[U-Boot] [PATCH v4 0/2] ARM: mx5: add support for USB armory board

[Stefano Babic]

On 08/04/2015 19:00, Andrej Rosano wrote:
> Hi Stefano,
> 
> On Wed, Apr 08, 2015 at 10:53:02AM +0200, Stefano Babic wrote:
>> On 01/04/2015 13:32, Stefano Babic wrote:
>>> Hi Chris,
>>>
>>> On 01/04/2015 04:46, Chris Kuethe wrote:
>>>> Any chance of this being accepted into 2015.04?
>>>>
>>>
>>
>> checpatch reports some issues by patch 2/2. Can you please fix them and
>> resubmit ? Thanks !
> 
> Just resubmitted the v5 version.
> 

Thanks, it is ok, I merge it !

Regards,
Stefano


-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================