From mboxrd@z Thu Jan  1 00:00:00 1970
From: Baruch Siach <baruch@tkos.co.il>
Date: Thu, 06 Sep 2018 18:42:14 +0300
Subject: [U-Boot] [PULL] Please pull u-boot-imx
In-Reply-To: <CAOMZO5AsgbVKfNVaZbNHbLj=zP+RLJ_7L3agKoQmnYbjSEv-8A@mail.gmail.com>
References: <9d19bc5e-b7aa-d7e3-8eeb-b211360edca0@denx.de>
 <CALeDE9OF-Jzwh6S7GuuL1gVyKj=2NifSJLFA0_P7V-f6s-a1Nw@mail.gmail.com>
 <ff309842-5d2c-f5c2-ab12-026fcfade4e5@denx.de>
 <CALeDE9P1XodgqjGv8Sp8FtJaajUJaTnDQAAHKJxKwN701tzbCg@mail.gmail.com>
 <CAOMZO5AsgbVKfNVaZbNHbLj=zP+RLJ_7L3agKoQmnYbjSEv-8A@mail.gmail.com>
Message-ID: <87r2i64oq1.fsf@tkos.co.il>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Hi Fabio,

Fabio Estevam writes:
> Hi Peter,
>
> [Adding Jon and Baruch]
>
> On Thu, Sep 6, 2018 at 9:37 AM, Peter Robinson <pbrobinson@gmail.com> wrote:
>
>> It seems like the Wandboard Quad revB I have also works fine so It
>> might just be a regression in the mx6cuboxi target.
>
> I don't have access to a hummingboard2 to investigate it.
>
> Does this issue also happen on a mx6q cuboxi?
>
> Are you able to run a bisect?

I tested current master successfully on Hummingboard2 with i.MX6 Solo
(SOM rev 1.5):

U-Boot SPL 2018.09-rc3-00026-g4cdeda511f80 (Sep 06 2018 - 18:30:30 +0300)
Trying to boot from MMC1


U-Boot 2018.09-rc3-00026-g4cdeda511f80 (Sep 06 2018 - 18:30:30 +0300)

CPU:   Freescale i.MX6SOLO rev1.3 996 MHz (running at 792 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 38C
Reset cause: POR
Board: MX6 HummingBoard2 (som rev 1.5)
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   FEC
Error: FEC address not set.

Hit any key to stop autoboot:  0
=>

... and with i.MX6Q (SOM rev 1.3):

U-Boot SPL 2018.09-rc3-00026-g4cdeda511f80 (Sep 06 2018 - 18:30:30 +0300)
Trying to boot from MMC1


U-Boot 2018.09-rc3-00026-g4cdeda511f80 (Sep 06 2018 - 18:30:30 +0300)

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 27C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Card did not respond to voltage select!
Net:   FEC
Hit any key to stop autoboot:  0
=>

I don't have handy at the moment the exact same combination of HB2 with
i.MX6Q SOM rev 1.5.

I built mx6cuboxi_defconfig with no changes using Linaro GCC 7.3-2018.05.

baruch

--
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -