* [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The real time clocks have a bunch of generic properties that are needed in
a device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/rtc.txt | 34 +-------------
Documentation/devicetree/bindings/rtc/rtc.yaml | 50 +++++++++++++++++++-
2 files changed, 51 insertions(+), 33 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/rtc.yaml
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
index a97fc6a9a75e..4d6f81dccc68 100644
--- a/Documentation/devicetree/bindings/rtc/rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -1,36 +1,4 @@
-Generic device tree bindings for Real Time Clock devices
-========================================================
-
-This document describes generic bindings which can be used to describe Real Time
-Clock devices in a device tree.
-
-Required properties
--------------------
-
-- compatible : name of RTC device following generic names recommended practice.
-
-For other required properties e.g. to describe register sets,
-clocks, etc. check the binding documentation of the specific driver.
-
-Optional properties
--------------------
-
-- start-year : if provided, the default hardware range supported by the RTC is
- shifted so the first usable year is the specified one.
-
-The following properties may not be supported by all drivers. However, if a
-driver wants to support one of the below features, it should adapt the bindings
-below.
-- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
- if trickle charger should be enabled
-- trickle-diode-disable : Do not use internal trickle charger diode Should be
- given if internal trickle charger diode should be
- disabled
-- wakeup-source : Enables wake up of host system on alarm
-- quartz-load-femtofarads : The capacitive load of the quartz(x-tal),
- expressed in femto Farad (fF).
- The default value shall be listed (if optional),
- and likewise all valid values.
+This file has been moved to rtc.yaml.
Trivial RTCs
------------
diff --git a/Documentation/devicetree/bindings/rtc/rtc.yaml b/Documentation/devicetree/bindings/rtc/rtc.yaml
new file mode 100644
index 000000000000..ee237b2ed66a
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RTC Generic Binding
+
+maintainers:
+ - Alexandre Belloni <alexandre.belloni@bootlin.com>
+
+description: |
+ This document describes generic bindings which can be used to
+ describe Real Time Clock devices in a device tree.
+
+properties:
+ $nodename:
+ pattern: "^rtc(@.*|-[0-9a-f])*$"
+
+ quartz-load-femtofarads:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The capacitive load of the quartz(x-tal), expressed in femto
+ Farad (fF). The default value shall be listed (if optional),
+ and likewise all valid values.
+
+ start-year:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ If provided, the default hardware range supported by the RTC is
+ shifted so the first usable year is the specified one.
+
+ trickle-diode-disable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Do not use internal trickle charger diode. Should be given if
+ internal trickle charger diode should be disabled.
+
+ trickle-resistor-ohms:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selected resistor for trickle charger. Should be given
+ if trickle charger should be enabled.
+
+ wakeup-source:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Enables wake up of host system on alarm.
+
+...
base-commit: 531b0a360899269bd99a38ba9852a8ba46852bcd
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The real time clocks have a bunch of generic properties that are needed in
a device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/rtc.txt | 34 +-------------
Documentation/devicetree/bindings/rtc/rtc.yaml | 50 +++++++++++++++++++-
2 files changed, 51 insertions(+), 33 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/rtc.yaml
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
index a97fc6a9a75e..4d6f81dccc68 100644
--- a/Documentation/devicetree/bindings/rtc/rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -1,36 +1,4 @@
-Generic device tree bindings for Real Time Clock devices
-========================================================
-
-This document describes generic bindings which can be used to describe Real Time
-Clock devices in a device tree.
-
-Required properties
--------------------
-
-- compatible : name of RTC device following generic names recommended practice.
-
-For other required properties e.g. to describe register sets,
-clocks, etc. check the binding documentation of the specific driver.
-
-Optional properties
--------------------
-
-- start-year : if provided, the default hardware range supported by the RTC is
- shifted so the first usable year is the specified one.
-
-The following properties may not be supported by all drivers. However, if a
-driver wants to support one of the below features, it should adapt the bindings
-below.
-- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
- if trickle charger should be enabled
-- trickle-diode-disable : Do not use internal trickle charger diode Should be
- given if internal trickle charger diode should be
- disabled
-- wakeup-source : Enables wake up of host system on alarm
-- quartz-load-femtofarads : The capacitive load of the quartz(x-tal),
- expressed in femto Farad (fF).
- The default value shall be listed (if optional),
- and likewise all valid values.
+This file has been moved to rtc.yaml.
Trivial RTCs
------------
diff --git a/Documentation/devicetree/bindings/rtc/rtc.yaml b/Documentation/devicetree/bindings/rtc/rtc.yaml
new file mode 100644
index 000000000000..ee237b2ed66a
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RTC Generic Binding
+
+maintainers:
+ - Alexandre Belloni <alexandre.belloni@bootlin.com>
+
+description: |
+ This document describes generic bindings which can be used to
+ describe Real Time Clock devices in a device tree.
+
+properties:
+ $nodename:
+ pattern: "^rtc(@.*|-[0-9a-f])*$"
+
+ quartz-load-femtofarads:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The capacitive load of the quartz(x-tal), expressed in femto
+ Farad (fF). The default value shall be listed (if optional),
+ and likewise all valid values.
+
+ start-year:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ If provided, the default hardware range supported by the RTC is
+ shifted so the first usable year is the specified one.
+
+ trickle-diode-disable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Do not use internal trickle charger diode. Should be given if
+ internal trickle charger diode should be disabled.
+
+ trickle-resistor-ohms:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selected resistor for trickle charger. Should be given
+ if trickle charger should be enabled.
+
+ wakeup-source:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Enables wake up of host system on alarm.
+
+...
base-commit: 531b0a360899269bd99a38ba9852a8ba46852bcd
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The real time clocks have a bunch of generic properties that are needed in
a device tree. Add a YAML schemas for those.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/rtc.txt | 34 +-------------
Documentation/devicetree/bindings/rtc/rtc.yaml | 50 +++++++++++++++++++-
2 files changed, 51 insertions(+), 33 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/rtc.yaml
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
index a97fc6a9a75e..4d6f81dccc68 100644
--- a/Documentation/devicetree/bindings/rtc/rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -1,36 +1,4 @@
-Generic device tree bindings for Real Time Clock devices
-========================================================
-
-This document describes generic bindings which can be used to describe Real Time
-Clock devices in a device tree.
-
-Required properties
--------------------
-
-- compatible : name of RTC device following generic names recommended practice.
-
-For other required properties e.g. to describe register sets,
-clocks, etc. check the binding documentation of the specific driver.
-
-Optional properties
--------------------
-
-- start-year : if provided, the default hardware range supported by the RTC is
- shifted so the first usable year is the specified one.
-
-The following properties may not be supported by all drivers. However, if a
-driver wants to support one of the below features, it should adapt the bindings
-below.
-- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given
- if trickle charger should be enabled
-- trickle-diode-disable : Do not use internal trickle charger diode Should be
- given if internal trickle charger diode should be
- disabled
-- wakeup-source : Enables wake up of host system on alarm
-- quartz-load-femtofarads : The capacitive load of the quartz(x-tal),
- expressed in femto Farad (fF).
- The default value shall be listed (if optional),
- and likewise all valid values.
+This file has been moved to rtc.yaml.
Trivial RTCs
------------
diff --git a/Documentation/devicetree/bindings/rtc/rtc.yaml b/Documentation/devicetree/bindings/rtc/rtc.yaml
new file mode 100644
index 000000000000..ee237b2ed66a
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/rtc.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RTC Generic Binding
+
+maintainers:
+ - Alexandre Belloni <alexandre.belloni@bootlin.com>
+
+description: |
+ This document describes generic bindings which can be used to
+ describe Real Time Clock devices in a device tree.
+
+properties:
+ $nodename:
+ pattern: "^rtc(@.*|-[0-9a-f])*$"
+
+ quartz-load-femtofarads:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The capacitive load of the quartz(x-tal), expressed in femto
+ Farad (fF). The default value shall be listed (if optional),
+ and likewise all valid values.
+
+ start-year:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ If provided, the default hardware range supported by the RTC is
+ shifted so the first usable year is the specified one.
+
+ trickle-diode-disable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Do not use internal trickle charger diode. Should be given if
+ internal trickle charger diode should be disabled.
+
+ trickle-resistor-ohms:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Selected resistor for trickle charger. Should be given
+ if trickle charger should be enabled.
+
+ wakeup-source:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Enables wake up of host system on alarm.
+
+...
base-commit: 531b0a360899269bd99a38ba9852a8ba46852bcd
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 02/11] dt-bindings: rtc: Move trivial RTC over to a schemas of their own
2019-05-28 20:30 ` Maxime Ripard
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The RTC generic bindings has a bunch of devices that have a pretty simple
binding, with just compatible, reg and optional interrupts properties.
This is exactly what the trivial devices YAML schema has been created for,
except that they can also have the start-year property, but not any other
generic RTC property.
Let's create a schema with those constraints.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Move from trivial-devices to trivial-rtc
---
Documentation/devicetree/bindings/rtc/rtc.txt | 39 +-----
Documentation/devicetree/bindings/rtc/trivial-rtc.yaml | 92 +++++++++++-
2 files changed, 92 insertions(+), 39 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/trivial-rtc.yaml
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
index 4d6f81dccc68..b8d36fce5e2d 100644
--- a/Documentation/devicetree/bindings/rtc/rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -1,40 +1 @@
This file has been moved to rtc.yaml.
-
-Trivial RTCs
-------------
-
-This is a list of trivial RTC devices that have simple device tree
-bindings, consisting only of a compatible field, an address and
-possibly an interrupt line.
-
-
-Compatible Vendor / Chip
-========== =============
-abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
-abracon,abeoz9 AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface
-dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
-dallas,ds1672 Dallas DS1672 Real-time Clock
-dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM
-epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE
-epson,rx8571 I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM
-epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE
-emmicro,em3027 EM Microelectronic EM3027 Real-time Clock
-isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM
-isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM
-isil,isl12022 Intersil ISL12022 Real-time Clock
-microcrystal,rv3028 Real Time Clock Module with I2C-Bus
-microcrystal,rv3029 Real Time Clock Module with I2C-Bus
-microcrystal,rv8523 Real Time Clock
-nxp,pcf2127 Real-time clock
-nxp,pcf2129 Real-time clock
-nxp,pcf8563 Real-time clock/calendar
-pericom,pt7c4338 Real-time Clock Module
-ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-sii,s35390a 2-wire CMOS real-time clock
-whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-xircom,x1205 Xircom X1205 I2C RTC
diff --git a/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml
new file mode 100644
index 000000000000..0c12ce9a9b45
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml
@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/trivial-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Trivial RTCs
+
+maintainers:
+ - Alexandre Belloni <alexandre.belloni@bootlin.com>
+
+description: |
+ This is a list of trivial RTC devices that have simple device tree
+ bindings, consisting only of a compatible field, an address and
+ possibly an interrupt line.
+
+allOf:
+ - $ref: "rtc.yaml#"
+
+properties:
+ compatible:
+ enum:
+ # AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
+ - abracon,abb5zes3
+ # AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface
+ - abracon,abeoz9
+ # I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
+ - dallas,ds1374
+ # Dallas DS1672 Real-time Clock
+ - dallas,ds1672
+ # Extremely Accurate I²C RTC with Integrated Crystal and SRAM
+ - dallas,ds3232
+ # I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+ - epson,rx8010
+ # I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM
+ - epson,rx8571
+ # I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+ - epson,rx8581
+ # Intersil ISL1208 Low Power RTC with Battery Backed SRAM
+ - isil,isl1208
+ # Intersil ISL1218 Low Power RTC with Battery Backed SRAM
+ - isil,isl1218
+ # Intersil ISL12022 Real-time Clock
+ - isil,isl12022
+ # Real Time Clock Module with I2C-Bus
+ - microcrystal,rv3028
+ # Real Time Clock Module with I2C-Bus
+ - microcrystal,rv3029
+ # Real Time Clock
+ - microcrystal,rv8523
+ # Real-time clock
+ - nxp,pcf2127
+ # Real-time clock
+ - nxp,pcf2129
+ # Real-time clock/calendar
+ - nxp,pcf8563
+ # Real-time Clock Module
+ - pericom,pt7c4338
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,r2025sd
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,r2221tl
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rs5c372a
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rs5c372b
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rv5c386
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rv5c387a
+ # 2-wire CMOS real-time clock
+ - sii,s35390a
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - whwave,sd3078
+ # Xircom X1205 I2C RTC
+ - xircom,x1205
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ start-year: true
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+...
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 02/11] dt-bindings: rtc: Move trivial RTC over to a schemas of their own
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The RTC generic bindings has a bunch of devices that have a pretty simple
binding, with just compatible, reg and optional interrupts properties.
This is exactly what the trivial devices YAML schema has been created for,
except that they can also have the start-year property, but not any other
generic RTC property.
Let's create a schema with those constraints.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Move from trivial-devices to trivial-rtc
---
Documentation/devicetree/bindings/rtc/rtc.txt | 39 +-----
Documentation/devicetree/bindings/rtc/trivial-rtc.yaml | 92 +++++++++++-
2 files changed, 92 insertions(+), 39 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/trivial-rtc.yaml
diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt
index 4d6f81dccc68..b8d36fce5e2d 100644
--- a/Documentation/devicetree/bindings/rtc/rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc.txt
@@ -1,40 +1 @@
This file has been moved to rtc.yaml.
-
-Trivial RTCs
-------------
-
-This is a list of trivial RTC devices that have simple device tree
-bindings, consisting only of a compatible field, an address and
-possibly an interrupt line.
-
-
-Compatible Vendor / Chip
-========== =============
-abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
-abracon,abeoz9 AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface
-dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
-dallas,ds1672 Dallas DS1672 Real-time Clock
-dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM
-epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE
-epson,rx8571 I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM
-epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE
-emmicro,em3027 EM Microelectronic EM3027 Real-time Clock
-isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM
-isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM
-isil,isl12022 Intersil ISL12022 Real-time Clock
-microcrystal,rv3028 Real Time Clock Module with I2C-Bus
-microcrystal,rv3029 Real Time Clock Module with I2C-Bus
-microcrystal,rv8523 Real Time Clock
-nxp,pcf2127 Real-time clock
-nxp,pcf2129 Real-time clock
-nxp,pcf8563 Real-time clock/calendar
-pericom,pt7c4338 Real-time Clock Module
-ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-sii,s35390a 2-wire CMOS real-time clock
-whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
-xircom,x1205 Xircom X1205 I2C RTC
diff --git a/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml
new file mode 100644
index 000000000000..0c12ce9a9b45
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/trivial-rtc.yaml
@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/trivial-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Trivial RTCs
+
+maintainers:
+ - Alexandre Belloni <alexandre.belloni@bootlin.com>
+
+description: |
+ This is a list of trivial RTC devices that have simple device tree
+ bindings, consisting only of a compatible field, an address and
+ possibly an interrupt line.
+
+allOf:
+ - $ref: "rtc.yaml#"
+
+properties:
+ compatible:
+ enum:
+ # AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface
+ - abracon,abb5zes3
+ # AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface
+ - abracon,abeoz9
+ # I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output
+ - dallas,ds1374
+ # Dallas DS1672 Real-time Clock
+ - dallas,ds1672
+ # Extremely Accurate I²C RTC with Integrated Crystal and SRAM
+ - dallas,ds3232
+ # I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+ - epson,rx8010
+ # I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM
+ - epson,rx8571
+ # I2C-BUS INTERFACE REAL TIME CLOCK MODULE
+ - epson,rx8581
+ # Intersil ISL1208 Low Power RTC with Battery Backed SRAM
+ - isil,isl1208
+ # Intersil ISL1218 Low Power RTC with Battery Backed SRAM
+ - isil,isl1218
+ # Intersil ISL12022 Real-time Clock
+ - isil,isl12022
+ # Real Time Clock Module with I2C-Bus
+ - microcrystal,rv3028
+ # Real Time Clock Module with I2C-Bus
+ - microcrystal,rv3029
+ # Real Time Clock
+ - microcrystal,rv8523
+ # Real-time clock
+ - nxp,pcf2127
+ # Real-time clock
+ - nxp,pcf2129
+ # Real-time clock/calendar
+ - nxp,pcf8563
+ # Real-time Clock Module
+ - pericom,pt7c4338
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,r2025sd
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,r2221tl
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rs5c372a
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rs5c372b
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rv5c386
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - ricoh,rv5c387a
+ # 2-wire CMOS real-time clock
+ - sii,s35390a
+ # I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
+ - whwave,sd3078
+ # Xircom X1205 I2C RTC
+ - xircom,x1205
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ start-year: true
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+...
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 03/11] dt-bindings: rtc: Convert Allwinner A10 RTC to a schema
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The older Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml | 43 +++++++++++++++++++++++++++++++++++++++++++
Documentation/devicetree/bindings/rtc/sunxi-rtc.txt | 17 -----------------
2 files changed, 43 insertions(+), 17 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
delete mode 100644 Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
new file mode 100644
index 000000000000..46d69c32b89b
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/allwinner,sun4i-a10-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 RTC Device Tree Bindings
+
+allOf:
+ - $ref: "rtc.yaml#"
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+ - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+ compatible:
+ enum:
+ - allwinner,sun4i-a10-rtc
+ - allwinner,sun7i-a20-rtc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ rtc: rtc@1c20d00 {
+ compatible = "allwinner,sun4i-a10-rtc";
+ reg = <0x01c20d00 0x20>;
+ interrupts = <24>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
deleted file mode 100644
index 4a8d79c1cf08..000000000000
--- a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-* sun4i/sun7i Real Time Clock
-
-RTC controller for the Allwinner A10/A20
-
-Required properties:
-- compatible : Should be "allwinner,sun4i-a10-rtc" or "allwinner,sun7i-a20-rtc"
-- reg: physical base address of the controller and length of memory mapped
- region.
-- interrupts: IRQ line for the RTC.
-
-Example:
-
-rtc: rtc@1c20d00 {
- compatible = "allwinner,sun4i-a10-rtc";
- reg = <0x01c20d00 0x20>;
- interrupts = <24>;
-};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 03/11] dt-bindings: rtc: Convert Allwinner A10 RTC to a schema
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The older Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml | 43 +++++++++++++++++++++++++++++++++++++++++++
Documentation/devicetree/bindings/rtc/sunxi-rtc.txt | 17 -----------------
2 files changed, 43 insertions(+), 17 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
delete mode 100644 Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
new file mode 100644
index 000000000000..46d69c32b89b
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/allwinner,sun4i-a10-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 RTC Device Tree Bindings
+
+allOf:
+ - $ref: "rtc.yaml#"
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+ - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+ compatible:
+ enum:
+ - allwinner,sun4i-a10-rtc
+ - allwinner,sun7i-a20-rtc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ rtc: rtc@1c20d00 {
+ compatible = "allwinner,sun4i-a10-rtc";
+ reg = <0x01c20d00 0x20>;
+ interrupts = <24>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
deleted file mode 100644
index 4a8d79c1cf08..000000000000
--- a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-* sun4i/sun7i Real Time Clock
-
-RTC controller for the Allwinner A10/A20
-
-Required properties:
-- compatible : Should be "allwinner,sun4i-a10-rtc" or "allwinner,sun7i-a20-rtc"
-- reg: physical base address of the controller and length of memory mapped
- region.
-- interrupts: IRQ line for the RTC.
-
-Example:
-
-rtc: rtc@1c20d00 {
- compatible = "allwinner,sun4i-a10-rtc";
- reg = <0x01c20d00 0x20>;
- interrupts = <24>;
-};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 03/11] dt-bindings: rtc: Convert Allwinner A10 RTC to a schema
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The older Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml | 43 +++++++++++++++++++++++++++++++++++++++++++
Documentation/devicetree/bindings/rtc/sunxi-rtc.txt | 17 -----------------
2 files changed, 43 insertions(+), 17 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
delete mode 100644 Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
new file mode 100644
index 000000000000..46d69c32b89b
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun4i-a10-rtc.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/allwinner,sun4i-a10-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A10 RTC Device Tree Bindings
+
+allOf:
+ - $ref: "rtc.yaml#"
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+ - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+ compatible:
+ enum:
+ - allwinner,sun4i-a10-rtc
+ - allwinner,sun7i-a20-rtc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ rtc: rtc@1c20d00 {
+ compatible = "allwinner,sun4i-a10-rtc";
+ reg = <0x01c20d00 0x20>;
+ interrupts = <24>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt b/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
deleted file mode 100644
index 4a8d79c1cf08..000000000000
--- a/Documentation/devicetree/bindings/rtc/sunxi-rtc.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-* sun4i/sun7i Real Time Clock
-
-RTC controller for the Allwinner A10/A20
-
-Required properties:
-- compatible : Should be "allwinner,sun4i-a10-rtc" or "allwinner,sun7i-a20-rtc"
-- reg: physical base address of the controller and length of memory mapped
- region.
-- interrupts: IRQ line for the RTC.
-
-Example:
-
-rtc: rtc@1c20d00 {
- compatible = "allwinner,sun4i-a10-rtc";
- reg = <0x01c20d00 0x20>;
- interrupts = <24>;
-};
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 04/11] dt-bindings: rtc: Convert Allwinner A31 RTC to a schema
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The newer Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Add back the R40 compatible
---
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 115 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
Documentation/devicetree/bindings/rtc/sun6i-rtc.txt | 46 +-----------------------------
2 files changed, 115 insertions(+), 46 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
delete mode 100644 Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
new file mode 100644
index 000000000000..f154bbba6a69
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/allwinner,sun6i-a31-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 RTC Device Tree Bindings
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+ - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+ "#clock-cells":
+ const: 1
+
+ compatible:
+ oneOf:
+ - const: allwinner,sun6i-a31-rtc
+ - const: allwinner,sun8i-a23-rtc
+ - const: allwinner,sun8i-h3-rtc
+ - items:
+ - const: allwinner,sun8i-r40-rtc
+ - const: allwinner,sun8i-h3-rtc
+ - const: allwinner,sun8i-v3-rtc
+ - const: allwinner,sun50i-h5-rtc
+ - items:
+ - const: allwinner,sun50i-a64-rtc
+ - const: allwinner,sun8i-h3-rtc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: RTC Alarm 0
+ - description: RTC Alarm 1
+
+ clocks:
+ maxItems: 1
+
+ clock-output-names:
+ minItems: 1
+ maxItems: 3
+ description:
+ The RTC provides up to three clocks
+ - the Low Frequency Oscillator or LOSC, at index 0,
+ - the Low Frequency Oscillator External output (X32KFOUT in
+ the datasheet), at index 1,
+ - the Internal Oscillator, at index 2.
+
+allOf:
+ - $ref: "rtc.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: allwinner,sun6i-a31-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 1
+ maxItems: 1
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-a23-rtc
+ - allwinner,sun8i-v3-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 2
+ maxItems: 2
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-h3-rtc
+ - allwinner,sun50i-h5-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 3
+ maxItems: 3
+
+required:
+ - "#clock-cells"
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-output-names
+
+additionalProperties: false
+
+examples:
+ - |
+ rtc: rtc@1f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x400>;
+ interrupts = <0 40 4>, <0 41 4>;
+ clock-output-names = "osc32k";
+ clocks = <&ext_osc32k>;
+ #clock-cells = <1>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
deleted file mode 100644
index 6b732c41392b..000000000000
--- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* sun6i Real Time Clock
-
-RTC controller for the Allwinner A31
-
-Required properties:
-- compatible : Should be one of the following combinations:
- - "allwinner,sun6i-a31-rtc"
- - "allwinner,sun8i-a23-rtc"
- - "allwinner,sun8i-h3-rtc"
- - "allwinner,sun8i-r40-rtc", "allwinner,sun8i-h3-rtc"
- - "allwinner,sun8i-v3-rtc"
- - "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc"
- - "allwinner,sun50i-h5-rtc"
-
- Where there are two or more compatible strings, this
- denotes the hardware covered by the most specific one
- is backward-compatible with the latter ones, and the
- implementation for the latter ones can be used, albeit
- with reduced functionality.
-
-- reg : physical base address of the controller and length of
- memory mapped region.
-- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order.
-
-Required properties for new device trees
-- clocks : phandle to the 32kHz external oscillator
-- clock-output-names : names of up to three clock outputs. See below.
-- #clock-cells : must be equal to 1.
-
-The RTC provides the following clocks at the given indices:
-- 0: LOSC
-- 1: LOSC external output, known as X32KFOUT in the datasheet.
- This clock is not available on the A31 and is deprecated for old
- device trees still using the "allwinner,sun6i-a31-rtc" compatible.
-- 2: InternalOSC, or internal RC oscillator (A64/H3/H5 only)
-
-Example:
-
-rtc: rtc@1f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x400>;
- interrupts = <0 40 4>, <0 41 4>;
- clock-output-names = "osc32k";
- clocks = <&ext_osc32k>;
- #clock-cells = <1>;
-};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 04/11] dt-bindings: rtc: Convert Allwinner A31 RTC to a schema
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The newer Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Add back the R40 compatible
---
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 115 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
Documentation/devicetree/bindings/rtc/sun6i-rtc.txt | 46 +-----------------------------
2 files changed, 115 insertions(+), 46 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
delete mode 100644 Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
new file mode 100644
index 000000000000..f154bbba6a69
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/allwinner,sun6i-a31-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 RTC Device Tree Bindings
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+ - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+ "#clock-cells":
+ const: 1
+
+ compatible:
+ oneOf:
+ - const: allwinner,sun6i-a31-rtc
+ - const: allwinner,sun8i-a23-rtc
+ - const: allwinner,sun8i-h3-rtc
+ - items:
+ - const: allwinner,sun8i-r40-rtc
+ - const: allwinner,sun8i-h3-rtc
+ - const: allwinner,sun8i-v3-rtc
+ - const: allwinner,sun50i-h5-rtc
+ - items:
+ - const: allwinner,sun50i-a64-rtc
+ - const: allwinner,sun8i-h3-rtc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: RTC Alarm 0
+ - description: RTC Alarm 1
+
+ clocks:
+ maxItems: 1
+
+ clock-output-names:
+ minItems: 1
+ maxItems: 3
+ description:
+ The RTC provides up to three clocks
+ - the Low Frequency Oscillator or LOSC, at index 0,
+ - the Low Frequency Oscillator External output (X32KFOUT in
+ the datasheet), at index 1,
+ - the Internal Oscillator, at index 2.
+
+allOf:
+ - $ref: "rtc.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: allwinner,sun6i-a31-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 1
+ maxItems: 1
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-a23-rtc
+ - allwinner,sun8i-v3-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 2
+ maxItems: 2
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-h3-rtc
+ - allwinner,sun50i-h5-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 3
+ maxItems: 3
+
+required:
+ - "#clock-cells"
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-output-names
+
+additionalProperties: false
+
+examples:
+ - |
+ rtc: rtc@1f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x400>;
+ interrupts = <0 40 4>, <0 41 4>;
+ clock-output-names = "osc32k";
+ clocks = <&ext_osc32k>;
+ #clock-cells = <1>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
deleted file mode 100644
index 6b732c41392b..000000000000
--- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* sun6i Real Time Clock
-
-RTC controller for the Allwinner A31
-
-Required properties:
-- compatible : Should be one of the following combinations:
- - "allwinner,sun6i-a31-rtc"
- - "allwinner,sun8i-a23-rtc"
- - "allwinner,sun8i-h3-rtc"
- - "allwinner,sun8i-r40-rtc", "allwinner,sun8i-h3-rtc"
- - "allwinner,sun8i-v3-rtc"
- - "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc"
- - "allwinner,sun50i-h5-rtc"
-
- Where there are two or more compatible strings, this
- denotes the hardware covered by the most specific one
- is backward-compatible with the latter ones, and the
- implementation for the latter ones can be used, albeit
- with reduced functionality.
-
-- reg : physical base address of the controller and length of
- memory mapped region.
-- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order.
-
-Required properties for new device trees
-- clocks : phandle to the 32kHz external oscillator
-- clock-output-names : names of up to three clock outputs. See below.
-- #clock-cells : must be equal to 1.
-
-The RTC provides the following clocks at the given indices:
-- 0: LOSC
-- 1: LOSC external output, known as X32KFOUT in the datasheet.
- This clock is not available on the A31 and is deprecated for old
- device trees still using the "allwinner,sun6i-a31-rtc" compatible.
-- 2: InternalOSC, or internal RC oscillator (A64/H3/H5 only)
-
-Example:
-
-rtc: rtc@1f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x400>;
- interrupts = <0 40 4>, <0 41 4>;
- clock-output-names = "osc32k";
- clocks = <&ext_osc32k>;
- #clock-cells = <1>;
-};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 04/11] dt-bindings: rtc: Convert Allwinner A31 RTC to a schema
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The newer Allwinner SoCs have an embedded RTC supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Add back the R40 compatible
---
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 115 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
Documentation/devicetree/bindings/rtc/sun6i-rtc.txt | 46 +-----------------------------
2 files changed, 115 insertions(+), 46 deletions(-)
create mode 100644 Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
delete mode 100644 Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
new file mode 100644
index 000000000000..f154bbba6a69
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/allwinner,sun6i-a31-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A31 RTC Device Tree Bindings
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+ - Maxime Ripard <maxime.ripard@bootlin.com>
+
+properties:
+ "#clock-cells":
+ const: 1
+
+ compatible:
+ oneOf:
+ - const: allwinner,sun6i-a31-rtc
+ - const: allwinner,sun8i-a23-rtc
+ - const: allwinner,sun8i-h3-rtc
+ - items:
+ - const: allwinner,sun8i-r40-rtc
+ - const: allwinner,sun8i-h3-rtc
+ - const: allwinner,sun8i-v3-rtc
+ - const: allwinner,sun50i-h5-rtc
+ - items:
+ - const: allwinner,sun50i-a64-rtc
+ - const: allwinner,sun8i-h3-rtc
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ items:
+ - description: RTC Alarm 0
+ - description: RTC Alarm 1
+
+ clocks:
+ maxItems: 1
+
+ clock-output-names:
+ minItems: 1
+ maxItems: 3
+ description:
+ The RTC provides up to three clocks
+ - the Low Frequency Oscillator or LOSC, at index 0,
+ - the Low Frequency Oscillator External output (X32KFOUT in
+ the datasheet), at index 1,
+ - the Internal Oscillator, at index 2.
+
+allOf:
+ - $ref: "rtc.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: allwinner,sun6i-a31-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 1
+ maxItems: 1
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-a23-rtc
+ - allwinner,sun8i-v3-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 2
+ maxItems: 2
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - allwinner,sun8i-h3-rtc
+ - allwinner,sun50i-h5-rtc
+
+ then:
+ properties:
+ clock-output-names:
+ minItems: 3
+ maxItems: 3
+
+required:
+ - "#clock-cells"
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-output-names
+
+additionalProperties: false
+
+examples:
+ - |
+ rtc: rtc@1f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x400>;
+ interrupts = <0 40 4>, <0 41 4>;
+ clock-output-names = "osc32k";
+ clocks = <&ext_osc32k>;
+ #clock-cells = <1>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
deleted file mode 100644
index 6b732c41392b..000000000000
--- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* sun6i Real Time Clock
-
-RTC controller for the Allwinner A31
-
-Required properties:
-- compatible : Should be one of the following combinations:
- - "allwinner,sun6i-a31-rtc"
- - "allwinner,sun8i-a23-rtc"
- - "allwinner,sun8i-h3-rtc"
- - "allwinner,sun8i-r40-rtc", "allwinner,sun8i-h3-rtc"
- - "allwinner,sun8i-v3-rtc"
- - "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc"
- - "allwinner,sun50i-h5-rtc"
-
- Where there are two or more compatible strings, this
- denotes the hardware covered by the most specific one
- is backward-compatible with the latter ones, and the
- implementation for the latter ones can be used, albeit
- with reduced functionality.
-
-- reg : physical base address of the controller and length of
- memory mapped region.
-- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order.
-
-Required properties for new device trees
-- clocks : phandle to the 32kHz external oscillator
-- clock-output-names : names of up to three clock outputs. See below.
-- #clock-cells : must be equal to 1.
-
-The RTC provides the following clocks at the given indices:
-- 0: LOSC
-- 1: LOSC external output, known as X32KFOUT in the datasheet.
- This clock is not available on the A31 and is deprecated for old
- device trees still using the "allwinner,sun6i-a31-rtc" compatible.
-- 2: InternalOSC, or internal RC oscillator (A64/H3/H5 only)
-
-Example:
-
-rtc: rtc@1f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x400>;
- interrupts = <0 40 4>, <0 41 4>;
- clock-output-names = "osc32k";
- clocks = <&ext_osc32k>;
- #clock-cells = <1>;
-};
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 05/11] dt-bindings: rtc: sun6i: Add the R40 RTC compatible
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The R40 has a pretty different RTC compared to the other SoCs we've
encountered so far, the most important difference being that it now has
only a single interrupt, compared to the previous SoCs having two.
Let's add a compatible for that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 25 ++++++++++++++++++++++---
1 file changed, 22 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index f154bbba6a69..924622f39c44 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -19,9 +19,7 @@ properties:
- const: allwinner,sun6i-a31-rtc
- const: allwinner,sun8i-a23-rtc
- const: allwinner,sun8i-h3-rtc
- - items:
- - const: allwinner,sun8i-r40-rtc
- - const: allwinner,sun8i-h3-rtc
+ - const: allwinner,sun8i-r40-rtc
- const: allwinner,sun8i-v3-rtc
- const: allwinner,sun50i-h5-rtc
- items:
@@ -32,6 +30,8 @@ properties:
maxItems: 1
interrupts:
+ minItems: 1
+ maxItems: 2
items:
- description: RTC Alarm 0
- description: RTC Alarm 1
@@ -69,6 +69,7 @@ allOf:
contains:
enum:
- allwinner,sun8i-a23-rtc
+ - allwinner,sun8i-r40-rtc
- allwinner,sun8i-v3-rtc
then:
@@ -91,6 +92,24 @@ allOf:
minItems: 3
maxItems: 3
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: allwinner,sun8i-r40-rtc
+
+ then:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
+
+ else:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
required:
- "#clock-cells"
- compatible
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 05/11] dt-bindings: rtc: sun6i: Add the R40 RTC compatible
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The R40 has a pretty different RTC compared to the other SoCs we've
encountered so far, the most important difference being that it now has
only a single interrupt, compared to the previous SoCs having two.
Let's add a compatible for that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 25 ++++++++++++++++++++++---
1 file changed, 22 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index f154bbba6a69..924622f39c44 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -19,9 +19,7 @@ properties:
- const: allwinner,sun6i-a31-rtc
- const: allwinner,sun8i-a23-rtc
- const: allwinner,sun8i-h3-rtc
- - items:
- - const: allwinner,sun8i-r40-rtc
- - const: allwinner,sun8i-h3-rtc
+ - const: allwinner,sun8i-r40-rtc
- const: allwinner,sun8i-v3-rtc
- const: allwinner,sun50i-h5-rtc
- items:
@@ -32,6 +30,8 @@ properties:
maxItems: 1
interrupts:
+ minItems: 1
+ maxItems: 2
items:
- description: RTC Alarm 0
- description: RTC Alarm 1
@@ -69,6 +69,7 @@ allOf:
contains:
enum:
- allwinner,sun8i-a23-rtc
+ - allwinner,sun8i-r40-rtc
- allwinner,sun8i-v3-rtc
then:
@@ -91,6 +92,24 @@ allOf:
minItems: 3
maxItems: 3
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: allwinner,sun8i-r40-rtc
+
+ then:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
+
+ else:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
required:
- "#clock-cells"
- compatible
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 05/11] dt-bindings: rtc: sun6i: Add the R40 RTC compatible
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The R40 has a pretty different RTC compared to the other SoCs we've
encountered so far, the most important difference being that it now has
only a single interrupt, compared to the previous SoCs having two.
Let's add a compatible for that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 25 ++++++++++++++++++++++---
1 file changed, 22 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index f154bbba6a69..924622f39c44 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -19,9 +19,7 @@ properties:
- const: allwinner,sun6i-a31-rtc
- const: allwinner,sun8i-a23-rtc
- const: allwinner,sun8i-h3-rtc
- - items:
- - const: allwinner,sun8i-r40-rtc
- - const: allwinner,sun8i-h3-rtc
+ - const: allwinner,sun8i-r40-rtc
- const: allwinner,sun8i-v3-rtc
- const: allwinner,sun50i-h5-rtc
- items:
@@ -32,6 +30,8 @@ properties:
maxItems: 1
interrupts:
+ minItems: 1
+ maxItems: 2
items:
- description: RTC Alarm 0
- description: RTC Alarm 1
@@ -69,6 +69,7 @@ allOf:
contains:
enum:
- allwinner,sun8i-a23-rtc
+ - allwinner,sun8i-r40-rtc
- allwinner,sun8i-v3-rtc
then:
@@ -91,6 +92,24 @@ allOf:
minItems: 3
maxItems: 3
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: allwinner,sun8i-r40-rtc
+
+ then:
+ properties:
+ interrupts:
+ minItems: 1
+ maxItems: 1
+
+ else:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 2
+
required:
- "#clock-cells"
- compatible
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 06/11] rtc: sun6i: Add R40 compatible
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The R40 has a quite different RTC, with only a single interrupt line, but
two clock outputs. Let's add a compatible.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
drivers/rtc/rtc-sun6i.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c
index 11f56de52179..9fab8ed856f4 100644
--- a/drivers/rtc/rtc-sun6i.c
+++ b/drivers/rtc/rtc-sun6i.c
@@ -681,6 +681,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] = {
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
+ { .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ /* sentinel */ },
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 06/11] rtc: sun6i: Add R40 compatible
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The R40 has a quite different RTC, with only a single interrupt line, but
two clock outputs. Let's add a compatible.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
drivers/rtc/rtc-sun6i.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c
index 11f56de52179..9fab8ed856f4 100644
--- a/drivers/rtc/rtc-sun6i.c
+++ b/drivers/rtc/rtc-sun6i.c
@@ -681,6 +681,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] = {
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
+ { .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ /* sentinel */ },
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 06/11] rtc: sun6i: Add R40 compatible
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The R40 has a quite different RTC, with only a single interrupt line, but
two clock outputs. Let's add a compatible.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
drivers/rtc/rtc-sun6i.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/rtc/rtc-sun6i.c b/drivers/rtc/rtc-sun6i.c
index 11f56de52179..9fab8ed856f4 100644
--- a/drivers/rtc/rtc-sun6i.c
+++ b/drivers/rtc/rtc-sun6i.c
@@ -681,6 +681,7 @@ static const struct of_device_id sun6i_rtc_dt_ids[] = {
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
+ { .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ /* sentinel */ },
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 07/11] ARM: dts: sun6i: Fix RTC node
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The RTC node doesn't match what is described in the binding for historical
reasons. Let's add the proper description.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun6i-a31.dtsi | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index a57cbf33c12f..9361ef70dbab 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -223,7 +223,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-output-names = "ext_osc32k";
};
/*
@@ -588,7 +588,7 @@
ccu: clock@1c20000 {
compatible = "allwinner,sun6i-a31-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
@@ -601,7 +601,7 @@
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
@@ -1287,10 +1287,13 @@
};
rtc: rtc@1f00000 {
+ #clock-cells = <1>;
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k";
};
nmi_intc: interrupt-controller@1f00c00 {
@@ -1308,7 +1311,7 @@
ar100: ar100_clk {
compatible = "allwinner,sun6i-a31-ar100-clk";
#clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>,
+ clocks = <&rtc 0>, <&osc24M>,
<&ccu CLK_PLL_PERIPH>,
<&ccu CLK_PLL_PERIPH>;
clock-output-names = "ar100";
@@ -1343,7 +1346,7 @@
ir_clk: ir_clk {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
- clocks = <&osc32k>, <&osc24M>;
+ clocks = <&rtc 0>, <&osc24M>;
clock-output-names = "ir";
};
@@ -1373,7 +1376,7 @@
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_rst 0>;
gpio-controller;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 07/11] ARM: dts: sun6i: Fix RTC node
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The RTC node doesn't match what is described in the binding for historical
reasons. Let's add the proper description.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun6i-a31.dtsi | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index a57cbf33c12f..9361ef70dbab 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -223,7 +223,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-output-names = "ext_osc32k";
};
/*
@@ -588,7 +588,7 @@
ccu: clock@1c20000 {
compatible = "allwinner,sun6i-a31-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
@@ -601,7 +601,7 @@
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
@@ -1287,10 +1287,13 @@
};
rtc: rtc@1f00000 {
+ #clock-cells = <1>;
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k";
};
nmi_intc: interrupt-controller@1f00c00 {
@@ -1308,7 +1311,7 @@
ar100: ar100_clk {
compatible = "allwinner,sun6i-a31-ar100-clk";
#clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>,
+ clocks = <&rtc 0>, <&osc24M>,
<&ccu CLK_PLL_PERIPH>,
<&ccu CLK_PLL_PERIPH>;
clock-output-names = "ar100";
@@ -1343,7 +1346,7 @@
ir_clk: ir_clk {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
- clocks = <&osc32k>, <&osc24M>;
+ clocks = <&rtc 0>, <&osc24M>;
clock-output-names = "ir";
};
@@ -1373,7 +1376,7 @@
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_rst 0>;
gpio-controller;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 07/11] ARM: dts: sun6i: Fix RTC node
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The RTC node doesn't match what is described in the binding for historical
reasons. Let's add the proper description.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun6i-a31.dtsi | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index a57cbf33c12f..9361ef70dbab 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -223,7 +223,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-output-names = "ext_osc32k";
};
/*
@@ -588,7 +588,7 @@
ccu: clock@1c20000 {
compatible = "allwinner,sun6i-a31-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
@@ -601,7 +601,7 @@
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
@@ -1287,10 +1287,13 @@
};
rtc: rtc@1f00000 {
+ #clock-cells = <1>;
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k";
};
nmi_intc: interrupt-controller@1f00c00 {
@@ -1308,7 +1311,7 @@
ar100: ar100_clk {
compatible = "allwinner,sun6i-a31-ar100-clk";
#clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>,
+ clocks = <&rtc 0>, <&osc24M>,
<&ccu CLK_PLL_PERIPH>,
<&ccu CLK_PLL_PERIPH>;
clock-output-names = "ar100";
@@ -1343,7 +1346,7 @@
ir_clk: ir_clk {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
- clocks = <&osc32k>, <&osc24M>;
+ clocks = <&rtc 0>, <&osc24M>;
clock-output-names = "ir";
};
@@ -1373,7 +1376,7 @@
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_rst 0>;
gpio-controller;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 08/11] ARM: dts: sun6i: Add external crystals accuracy
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The A31 datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun6i-a31.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index 9361ef70dbab..dcddc3392460 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -216,6 +216,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -223,6 +224,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
+ clock-accuracy = <50000>;
clock-output-names = "ext_osc32k";
};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 08/11] ARM: dts: sun6i: Add external crystals accuracy
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The A31 datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun6i-a31.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index 9361ef70dbab..dcddc3392460 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -216,6 +216,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -223,6 +224,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
+ clock-accuracy = <50000>;
clock-output-names = "ext_osc32k";
};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 08/11] ARM: dts: sun6i: Add external crystals accuracy
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The A31 datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun6i-a31.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index 9361ef70dbab..dcddc3392460 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -216,6 +216,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -223,6 +224,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
+ clock-accuracy = <50000>;
clock-output-names = "ext_osc32k";
};
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 09/11] ARM: dts: sun8i: v3s: Fix the RTC node
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
For some reason, while the v3s has a dedicated compatible in the RTC
binding, the one actually used was the A31's. However, it turns out that
the controller is pretty different (which justified the compatible).
Let's use the proper compatible, and use the proper binding description as
well.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Split that patch into two
---
arch/arm/boot/dts/sun8i-v3s.dtsi | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index df72b1719c34..6ba9377458b3 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -91,7 +91,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-output-names = "ext-osc32k";
};
};
@@ -264,17 +264,20 @@
ccu: clock@1c20000 {
compatible = "allwinner,sun8i-v3s-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
rtc: rtc@1c20400 {
- compatible = "allwinner,sun6i-a31-rtc";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-v3-rtc";
reg = <0x01c20400 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k", "osc32k-out";
};
pio: pinctrl@1c20800 {
@@ -282,7 +285,7 @@
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 09/11] ARM: dts: sun8i: v3s: Fix the RTC node
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
For some reason, while the v3s has a dedicated compatible in the RTC
binding, the one actually used was the A31's. However, it turns out that
the controller is pretty different (which justified the compatible).
Let's use the proper compatible, and use the proper binding description as
well.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Split that patch into two
---
arch/arm/boot/dts/sun8i-v3s.dtsi | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index df72b1719c34..6ba9377458b3 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -91,7 +91,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-output-names = "ext-osc32k";
};
};
@@ -264,17 +264,20 @@
ccu: clock@1c20000 {
compatible = "allwinner,sun8i-v3s-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
rtc: rtc@1c20400 {
- compatible = "allwinner,sun6i-a31-rtc";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-v3-rtc";
reg = <0x01c20400 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k", "osc32k-out";
};
pio: pinctrl@1c20800 {
@@ -282,7 +285,7 @@
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 09/11] ARM: dts: sun8i: v3s: Fix the RTC node
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
For some reason, while the v3s has a dedicated compatible in the RTC
binding, the one actually used was the A31's. However, it turns out that
the controller is pretty different (which justified the compatible).
Let's use the proper compatible, and use the proper binding description as
well.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
Changes from v1:
- Split that patch into two
---
arch/arm/boot/dts/sun8i-v3s.dtsi | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index df72b1719c34..6ba9377458b3 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -91,7 +91,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
- clock-output-names = "osc32k";
+ clock-output-names = "ext-osc32k";
};
};
@@ -264,17 +264,20 @@
ccu: clock@1c20000 {
compatible = "allwinner,sun8i-v3s-ccu";
reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
+ clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
rtc: rtc@1c20400 {
- compatible = "allwinner,sun6i-a31-rtc";
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-v3-rtc";
reg = <0x01c20400 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc32k>;
+ clock-output-names = "osc32k", "osc32k-out";
};
pio: pinctrl@1c20800 {
@@ -282,7 +285,7 @@
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 10/11] ARM: dts: sun8i: v3s: Add external crystals accuracy
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
The V3s datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-v3s.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index 6ba9377458b3..d7aef128acb3 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -84,6 +84,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -91,6 +92,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
+ clock-accuracy = <50000>;
clock-output-names = "ext-osc32k";
};
};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 10/11] ARM: dts: sun8i: v3s: Add external crystals accuracy
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The V3s datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-v3s.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index 6ba9377458b3..d7aef128acb3 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -84,6 +84,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -91,6 +92,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
+ clock-accuracy = <50000>;
clock-output-names = "ext-osc32k";
};
};
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 10/11] ARM: dts: sun8i: v3s: Add external crystals accuracy
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
The V3s datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-v3s.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index 6ba9377458b3..d7aef128acb3 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -84,6 +84,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
+ clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
@@ -91,6 +92,7 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
+ clock-accuracy = <50000>;
clock-output-names = "ext-osc32k";
};
};
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 11/11] ARM: dts: sun8i: r40: Change the RTC compatible
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-05-28 20:30 ` Maxime Ripard
-1 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: devicetree, linux-arm-kernel, linux-rtc
Unlike what's being reported in the device tree so far, the RTC in the R40
is quite different from the H3. Indeed it doesn't have the internal
oscillator output, and it has only a single interrupt. Let's add a
compatible for it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-r40.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
index bb856e53b806..6007d0cc252d 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -318,8 +318,7 @@
};
rtc: rtc@1c20400 {
- compatible = "allwinner,sun8i-r40-rtc",
- "allwinner,sun8i-h3-rtc";
+ compatible = "allwinner,sun8i-r40-rtc";
reg = <0x01c20400 0x400>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
clock-output-names = "osc32k", "osc32k-out";
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 11/11] ARM: dts: sun8i: r40: Change the RTC compatible
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
Unlike what's being reported in the device tree so far, the RTC in the R40
is quite different from the H3. Indeed it doesn't have the internal
oscillator output, and it has only a single interrupt. Let's add a
compatible for it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-r40.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
index bb856e53b806..6007d0cc252d 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -318,8 +318,7 @@
};
rtc: rtc@1c20400 {
- compatible = "allwinner,sun8i-r40-rtc",
- "allwinner,sun8i-h3-rtc";
+ compatible = "allwinner,sun8i-r40-rtc";
reg = <0x01c20400 0x400>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
clock-output-names = "osc32k", "osc32k-out";
--
git-series 0.9.1
^ permalink raw reply related [flat|nested] 35+ messages in thread
* [PATCH v2 11/11] ARM: dts: sun8i: r40: Change the RTC compatible
@ 2019-05-28 20:30 ` Maxime Ripard
0 siblings, 0 replies; 35+ messages in thread
From: Maxime Ripard @ 2019-05-28 20:30 UTC (permalink / raw)
To: Alexandre Belloni, Mark Rutland, Rob Herring, Frank Rowand,
Chen-Yu Tsai, Maxime Ripard
Cc: linux-rtc, devicetree, linux-arm-kernel
Unlike what's being reported in the device tree so far, the RTC in the R40
is quite different from the H3. Indeed it doesn't have the internal
oscillator output, and it has only a single interrupt. Let's add a
compatible for it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-r40.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
index bb856e53b806..6007d0cc252d 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -318,8 +318,7 @@
};
rtc: rtc@1c20400 {
- compatible = "allwinner,sun8i-r40-rtc",
- "allwinner,sun8i-h3-rtc";
+ compatible = "allwinner,sun8i-r40-rtc";
reg = <0x01c20400 0x400>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
clock-output-names = "osc32k", "osc32k-out";
--
git-series 0.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 35+ messages in thread
* Re: [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings
2019-05-28 20:30 ` Maxime Ripard
(?)
@ 2019-06-06 10:01 ` Alexandre Belloni
-1 siblings, 0 replies; 35+ messages in thread
From: Alexandre Belloni @ 2019-06-06 10:01 UTC (permalink / raw)
To: Maxime Ripard
Cc: Mark Rutland, Rob Herring, Frank Rowand, Chen-Yu Tsai,
devicetree, linux-arm-kernel, linux-rtc
On 28/05/2019 22:30:31+0200, Maxime Ripard wrote:
> The real time clocks have a bunch of generic properties that are needed in
> a device tree. Add a YAML schemas for those.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
> ---
> Documentation/devicetree/bindings/rtc/rtc.txt | 34 +-------------
> Documentation/devicetree/bindings/rtc/rtc.yaml | 50 +++++++++++++++++++-
> 2 files changed, 51 insertions(+), 33 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/rtc/rtc.yaml
>
Applied 1 to 6, thanks.
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings
@ 2019-06-06 10:01 ` Alexandre Belloni
0 siblings, 0 replies; 35+ messages in thread
From: Alexandre Belloni @ 2019-06-06 10:01 UTC (permalink / raw)
To: Maxime Ripard
Cc: Mark Rutland, devicetree, Chen-Yu Tsai, Rob Herring,
Frank Rowand, linux-arm-kernel, linux-rtc
On 28/05/2019 22:30:31+0200, Maxime Ripard wrote:
> The real time clocks have a bunch of generic properties that are needed in
> a device tree. Add a YAML schemas for those.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
> ---
> Documentation/devicetree/bindings/rtc/rtc.txt | 34 +-------------
> Documentation/devicetree/bindings/rtc/rtc.yaml | 50 +++++++++++++++++++-
> 2 files changed, 51 insertions(+), 33 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/rtc/rtc.yaml
>
Applied 1 to 6, thanks.
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 35+ messages in thread
* Re: [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings
@ 2019-06-06 10:01 ` Alexandre Belloni
0 siblings, 0 replies; 35+ messages in thread
From: Alexandre Belloni @ 2019-06-06 10:01 UTC (permalink / raw)
To: Maxime Ripard
Cc: Mark Rutland, devicetree, Chen-Yu Tsai, Rob Herring,
Frank Rowand, linux-arm-kernel, linux-rtc
On 28/05/2019 22:30:31+0200, Maxime Ripard wrote:
> The real time clocks have a bunch of generic properties that are needed in
> a device tree. Add a YAML schemas for those.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
> ---
> Documentation/devicetree/bindings/rtc/rtc.txt | 34 +-------------
> Documentation/devicetree/bindings/rtc/rtc.yaml | 50 +++++++++++++++++++-
> 2 files changed, 51 insertions(+), 33 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/rtc/rtc.yaml
>
Applied 1 to 6, thanks.
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 35+ messages in thread
end of thread, other threads:[~2019-06-06 10:04 UTC | newest]
Thread overview: 35+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-28 20:30 [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 02/11] dt-bindings: rtc: Move trivial RTC over to a schemas of their own Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 03/11] dt-bindings: rtc: Convert Allwinner A10 RTC to a schema Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 04/11] dt-bindings: rtc: Convert Allwinner A31 " Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 05/11] dt-bindings: rtc: sun6i: Add the R40 RTC compatible Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 06/11] rtc: sun6i: Add R40 compatible Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 07/11] ARM: dts: sun6i: Fix RTC node Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 08/11] ARM: dts: sun6i: Add external crystals accuracy Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 09/11] ARM: dts: sun8i: v3s: Fix the RTC node Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 10/11] ARM: dts: sun8i: v3s: Add external crystals accuracy Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` [PATCH v2 11/11] ARM: dts: sun8i: r40: Change the RTC compatible Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-05-28 20:30 ` Maxime Ripard
2019-06-06 10:01 ` [PATCH v2 01/11] dt-bindings: rtc: Add YAML schemas for the generic RTC bindings Alexandre Belloni
2019-06-06 10:01 ` Alexandre Belloni
2019-06-06 10:01 ` Alexandre Belloni
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.