* blank screen VGA or Serial while linux boot
@ 2016-12-28 14:17 Daniele Palumbo
2016-12-29 14:49 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 4+ messages in thread
From: Daniele Palumbo @ 2016-12-28 14:17 UTC (permalink / raw)
To: xen-devel
[-- Attachment #1.1.1: Type: text/plain, Size: 3308 bytes --]
Hi,
Sorry for bothering, I am following
https://wiki.xenproject.org/wiki/Xen_Serial_Console
and
http://www-archive.xenproject.org/files/xensummit_4/xensummit_linux_console_slides.pdf
And as written in
https://wiki.xenproject.org/wiki/XenParavirtOps
Here i am writing.
My goal is to have the same console output on VGA and internal serial port.
I am on gentoo, with Xen 4.6.4, custom kernel.
My kernel config is in attachment.
Test hardware is a Sun x4150, with ILOm.
Serial speed is set to 9600 bps, with console redirection (so all of the BIOS messages are shown).
See an example of my output in attachment (serial_out.txt), with the following settings:
GRUB_TERMINAL="console serial"
GRUB_SERIAL_COMMAND="serial --speed=9600 --unit=1 --word=8 --parity=no --stop=1"
GRUB_CMDLINE_XEN="loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga"
GRUB_CMDLINE_LINUX="xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset"
full grub.cfg in attachment.
As by the logs I am able to see the same terminal from BIOS to the XEN multiboot.
With xen multiboot i mean messages starting with
"(XEN) "
e.g.:
(XEN) Video information:Gentoo GNU/Linux (with Xen hypervisor)
(XEN) VGA is text mode 80x25, font 8x16
I am not able to get the same message across serial _AND_ vga terminal upon boot,
AFTER the xen multiboot.
With earlyprintk=xen i see also linux messages starting with
"[ 0.000000] "
e.g., last line seen is
[ 0.000000] Memory: 925860K/2097148K available (5475K kernel code, 570K rwdata, 2344K rodata, 992K init, 1
After that, i can always see the login prompt in both serial and VGA output.
About grub config, the basic stuff in /etc/default/grub is:
"""
GRUB_TERMINAL="console serial"
GRUB_SERIAL_COMMAND="serial --speed=9600 --unit=1 --word=8 --parity=no --stop=1"
GRUB_CMDLINE_XEN="loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga"
"""
nomodeset is not helping.
Seems like hvc0 contains only serial messages.
Seems also that setting 2 console in linux module would have exclusive access.
It is important to mention that i can always see grub and Xen logs in both serial and VGA device.
ttyS0 is not present at all in the dmesg.
# dmesg |grep tty
[ 0.648440] 00:02: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
#
Then i have tried out the following
# serial OK, no vga after XEN multiboot and earlyprintk
GRUB_CMDLINE_LINUX="console=hvc0 earlyprintk=xen"
# serial OK, no vga after XEN multiboot and earlyprintk
GRUB_CMDLINE_LINUX="console=hvc0 earlyprintk=xen nomodeset"
# serial OK, no vga after XEN multiboot and earlyprintk
GRUB_CMDLINE_LINUX="console=hvc0 earlyprintk=xen nomodeset vga=791"
# VGA OK, no serial after XEN multiboot and earlyprintk
GRUB_CMDLINE_LINUX="console=hvc0 console=tty1 earlyprintk=xen"
# VGA OK, no serial after XEN multiboot and earlyprintk
GRUB_CMDLINE_LINUX="console=xvc xencons=xvc console=hvc0 console=tty0 nomodeset earlyprintk=xen"
# VGA OK, no serial after XEN multiboot and earlyprintk
GRUB_CMDLINE_LINUX="xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset"
Really willing to understand how to get the proper output on both serial and VGA.
Thank you very much,
Daniele
[-- Attachment #1.1.2: config-4.4.26-xen-Dom0-44-r2 --]
[-- Type: application/octet-stream, Size: 96712 bytes --]
#
# Automatically generated file; DO NOT EDIT.
# Linux/x86 4.4.26-gentoo Kernel Configuration
#
#
# Gentoo Linux
#
CONFIG_GENTOO_LINUX=y
CONFIG_GENTOO_LINUX_UDEV=y
CONFIG_GENTOO_LINUX_PORTAGE=y
#
# Support for init systems, system and service managers
#
CONFIG_GENTOO_LINUX_INIT_SCRIPT=y
# CONFIG_GENTOO_LINUX_INIT_SYSTEMD is not set
CONFIG_64BIT=y
CONFIG_X86_64=y
CONFIG_X86=y
CONFIG_INSTRUCTION_DECODER=y
CONFIG_PERF_EVENTS_INTEL_UNCORE=y
CONFIG_OUTPUT_FORMAT="elf64-x86-64"
CONFIG_ARCH_DEFCONFIG="arch/x86/configs/x86_64_defconfig"
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_MMU=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_HAS_CPU_RELAX=y
CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
CONFIG_HAVE_SETUP_PER_CPU_AREA=y
CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK=y
CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARCH_WANT_HUGE_PMD_SHARE=y
CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
CONFIG_ZONE_DMA32=y
CONFIG_AUDIT_ARCH=y
CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_HAVE_INTEL_TXT=y
CONFIG_X86_64_SMP=y
CONFIG_ARCH_HWEIGHT_CFLAGS="-fcall-saved-rdi -fcall-saved-rsi -fcall-saved-rdx -fcall-saved-rcx -fcall-saved-r8 -fcall-saved-r9 -fcall-saved-r10 -fcall-saved-r11"
CONFIG_ARCH_SUPPORTS_UPROBES=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_PGTABLE_LEVELS=4
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_IRQ_WORK=y
CONFIG_BUILDTIME_EXTABLE_SORT=y
#
# General setup
#
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_CROSS_COMPILE=""
# CONFIG_COMPILE_TEST is not set
CONFIG_LOCALVERSION="-Dom0-44-r2"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_HAVE_KERNEL_LZ4=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_BZIP2 is not set
# CONFIG_KERNEL_LZMA is not set
# CONFIG_KERNEL_XZ is not set
# CONFIG_KERNEL_LZO is not set
# CONFIG_KERNEL_LZ4 is not set
CONFIG_DEFAULT_HOSTNAME="(none)"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
CONFIG_CROSS_MEMORY_ATTACH=y
CONFIG_FHANDLE=y
CONFIG_USELIB=y
CONFIG_AUDIT=y
CONFIG_HAVE_ARCH_AUDITSYSCALL=y
CONFIG_AUDITSYSCALL=y
CONFIG_AUDIT_WATCH=y
CONFIG_AUDIT_TREE=y
#
# IRQ subsystem
#
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_DOMAIN_HIERARCHY=y
CONFIG_GENERIC_MSI_IRQ=y
CONFIG_GENERIC_MSI_IRQ_DOMAIN=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_SPARSE_IRQ=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_ARCH_CLOCKSOURCE_DATA=y
CONFIG_CLOCKSOURCE_VALIDATE_LAST_CYCLE=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_GENERIC_CLOCKEVENTS_MIN_ADJUST=y
CONFIG_GENERIC_CMOS_UPDATE=y
#
# Timers subsystem
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ_COMMON=y
# CONFIG_HZ_PERIODIC is not set
CONFIG_NO_HZ_IDLE=y
# CONFIG_NO_HZ_FULL is not set
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
#
# CPU/Task time and stats accounting
#
CONFIG_TICK_CPU_ACCOUNTING=y
# CONFIG_VIRT_CPU_ACCOUNTING_GEN is not set
# CONFIG_IRQ_TIME_ACCOUNTING is not set
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
CONFIG_TASK_XACCT=y
CONFIG_TASK_IO_ACCOUNTING=y
#
# RCU Subsystem
#
CONFIG_TREE_RCU=y
# CONFIG_RCU_EXPERT is not set
CONFIG_SRCU=y
# CONFIG_TASKS_RCU is not set
CONFIG_RCU_STALL_COMMON=y
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_RCU_EXPEDITE_BOOT is not set
CONFIG_BUILD_BIN2C=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=20
CONFIG_LOG_CPU_MAX_BUF_SHIFT=12
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
CONFIG_ARCH_WANT_BATCHED_UNMAP_TLB_FLUSH=y
CONFIG_ARCH_SUPPORTS_INT128=y
# CONFIG_NUMA_BALANCING is not set
CONFIG_CGROUPS=y
# CONFIG_CGROUP_DEBUG is not set
CONFIG_CGROUP_FREEZER=y
# CONFIG_CGROUP_PIDS is not set
CONFIG_CGROUP_DEVICE=y
CONFIG_CPUSETS=y
CONFIG_PROC_PID_CPUSET=y
CONFIG_CGROUP_CPUACCT=y
# CONFIG_MEMCG is not set
# CONFIG_CGROUP_PERF is not set
CONFIG_CGROUP_SCHED=y
CONFIG_FAIR_GROUP_SCHED=y
# CONFIG_CFS_BANDWIDTH is not set
CONFIG_RT_GROUP_SCHED=y
# CONFIG_BLK_CGROUP is not set
# CONFIG_CHECKPOINT_RESTORE is not set
CONFIG_NAMESPACES=y
CONFIG_UTS_NS=y
CONFIG_IPC_NS=y
CONFIG_USER_NS=y
CONFIG_PID_NS=y
CONFIG_NET_NS=y
# CONFIG_SCHED_AUTOGROUP is not set
# CONFIG_SYSFS_DEPRECATED is not set
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
CONFIG_RD_XZ=y
CONFIG_RD_LZO=y
CONFIG_RD_LZ4=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_HAVE_UID16=y
CONFIG_SYSCTL_EXCEPTION_TRACE=y
CONFIG_HAVE_PCSPKR_PLATFORM=y
CONFIG_BPF=y
CONFIG_EXPERT=y
CONFIG_UID16=y
CONFIG_MULTIUSER=y
CONFIG_SGETMASK_SYSCALL=y
CONFIG_SYSFS_SYSCALL=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
# CONFIG_BPF_SYSCALL is not set
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_ADVISE_SYSCALLS=y
# CONFIG_USERFAULTFD is not set
CONFIG_PCI_QUIRKS=y
CONFIG_MEMBARRIER=y
CONFIG_EMBEDDED=y
CONFIG_HAVE_PERF_EVENTS=y
#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_COMPAT_BRK is not set
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_SYSTEM_DATA_VERIFICATION is not set
# CONFIG_PROFILING is not set
CONFIG_KEXEC_CORE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_OPROFILE_NMI_TIMER=y
# CONFIG_KPROBES is not set
# CONFIG_JUMP_LABEL is not set
# CONFIG_UPROBES is not set
# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_ARCH_USE_BUILTIN_BSWAP=y
CONFIG_USER_RETURN_NOTIFIER=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_OPTPROBES=y
CONFIG_HAVE_KPROBES_ON_FTRACE=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_MIXED_BREAKPOINTS_REGS=y
CONFIG_HAVE_USER_RETURN_NOTIFIER=y
CONFIG_HAVE_PERF_EVENTS_NMI=y
CONFIG_HAVE_PERF_REGS=y
CONFIG_HAVE_PERF_USER_STACK_DUMP=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG=y
CONFIG_HAVE_CMPXCHG_LOCAL=y
CONFIG_HAVE_CMPXCHG_DOUBLE=y
CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION=y
CONFIG_ARCH_WANT_OLD_COMPAT_IPC=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_SECCOMP_FILTER=y
CONFIG_HAVE_CC_STACKPROTECTOR=y
# CONFIG_CC_STACKPROTECTOR is not set
CONFIG_CC_STACKPROTECTOR_NONE=y
# CONFIG_CC_STACKPROTECTOR_REGULAR is not set
# CONFIG_CC_STACKPROTECTOR_STRONG is not set
CONFIG_HAVE_CONTEXT_TRACKING=y
CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
CONFIG_HAVE_ARCH_HUGE_VMAP=y
CONFIG_HAVE_ARCH_SOFT_DIRTY=y
CONFIG_MODULES_USE_ELF_RELA=y
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK=y
CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
CONFIG_HAVE_COPY_THREAD_TLS=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_COMPAT_OLD_SIGACTION=y
#
# GCOV-based kernel profiling
#
CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_MODULE_SIG is not set
# CONFIG_MODULE_COMPRESS is not set
CONFIG_MODULES_TREE_LOOKUP=y
CONFIG_BLOCK=y
CONFIG_BLK_DEV_BSG=y
CONFIG_BLK_DEV_BSGLIB=y
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_BLK_CMDLINE_PARSER is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_AIX_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
# CONFIG_CMDLINE_PARTITION is not set
CONFIG_BLOCK_COMPAT=y
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_DEADLINE=y
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="deadline"
CONFIG_PREEMPT_NOTIFIERS=y
CONFIG_INLINE_SPIN_UNLOCK_IRQ=y
CONFIG_INLINE_READ_UNLOCK=y
CONFIG_INLINE_READ_UNLOCK_IRQ=y
CONFIG_INLINE_WRITE_UNLOCK=y
CONFIG_INLINE_WRITE_UNLOCK_IRQ=y
CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
CONFIG_MUTEX_SPIN_ON_OWNER=y
CONFIG_RWSEM_SPIN_ON_OWNER=y
CONFIG_LOCK_SPIN_ON_OWNER=y
CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
CONFIG_QUEUED_RWLOCKS=y
CONFIG_FREEZER=y
#
# Processor type and features
#
CONFIG_ZONE_DMA=y
CONFIG_SMP=y
CONFIG_X86_FEATURE_NAMES=y
# CONFIG_X86_X2APIC is not set
CONFIG_X86_MPPARSE=y
# CONFIG_X86_EXTENDED_PLATFORM is not set
# CONFIG_X86_INTEL_LPSS is not set
# CONFIG_X86_AMD_PLATFORM_DEVICE is not set
# CONFIG_IOSF_MBI is not set
CONFIG_X86_SUPPORTS_MEMORY_FAILURE=y
CONFIG_SCHED_OMIT_FRAME_POINTER=y
CONFIG_HYPERVISOR_GUEST=y
CONFIG_PARAVIRT=y
# CONFIG_PARAVIRT_DEBUG is not set
CONFIG_PARAVIRT_SPINLOCKS=y
CONFIG_XEN=y
CONFIG_XEN_DOM0=y
CONFIG_XEN_PVHVM=y
CONFIG_XEN_512GB=y
CONFIG_XEN_SAVE_RESTORE=y
# CONFIG_XEN_PVH is not set
CONFIG_KVM_GUEST=y
# CONFIG_PARAVIRT_TIME_ACCOUNTING is not set
CONFIG_PARAVIRT_CLOCK=y
CONFIG_NO_BOOTMEM=y
# CONFIG_MK8 is not set
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_MATOM is not set
CONFIG_GENERIC_CPU=y
CONFIG_X86_INTERNODE_CACHE_SHIFT=6
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_TSC=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=64
CONFIG_X86_DEBUGCTLMSR=y
# CONFIG_PROCESSOR_SELECT is not set
CONFIG_CPU_SUP_INTEL=y
CONFIG_CPU_SUP_AMD=y
CONFIG_CPU_SUP_CENTAUR=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_DMI=y
CONFIG_GART_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_SWIOTLB=y
CONFIG_IOMMU_HELPER=y
# CONFIG_MAXSMP is not set
CONFIG_NR_CPUS=12
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_INTEL=y
CONFIG_X86_MCE_AMD=y
CONFIG_X86_MCE_THRESHOLD=y
CONFIG_X86_MCE_INJECT=m
CONFIG_X86_THERMAL_VECTOR=y
# CONFIG_VM86 is not set
CONFIG_X86_16BIT=y
CONFIG_X86_ESPFIX64=y
CONFIG_X86_VSYSCALL_EMULATION=y
# CONFIG_I8K is not set
CONFIG_MICROCODE=y
CONFIG_MICROCODE_INTEL=y
# CONFIG_MICROCODE_AMD is not set
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
CONFIG_ARCH_DMA_ADDR_T_64BIT=y
CONFIG_X86_DIRECT_GBPAGES=y
CONFIG_NUMA=y
CONFIG_AMD_NUMA=y
CONFIG_X86_64_ACPI_NUMA=y
CONFIG_NODES_SPAN_OTHER_NODES=y
# CONFIG_NUMA_EMU is not set
CONFIG_NODES_SHIFT=6
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_PROC_KCORE_TEXT=y
CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM=y
CONFIG_NEED_MULTIPLE_NODES=y
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_EXTREME=y
CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
CONFIG_SPARSEMEM_ALLOC_MEM_MAP_TOGETHER=y
CONFIG_SPARSEMEM_VMEMMAP=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
CONFIG_ARCH_DISCARD_MEMBLOCK=y
CONFIG_MEMORY_ISOLATION=y
# CONFIG_MOVABLE_NODE is not set
# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
# CONFIG_MEMORY_HOTPLUG is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_ARCH_ENABLE_SPLIT_PMD_PTLOCK=y
CONFIG_COMPACTION=y
CONFIG_MIGRATION=y
CONFIG_PHYS_ADDR_T_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_MMU_NOTIFIER=y
CONFIG_KSM=y
CONFIG_DEFAULT_MMAP_MIN_ADDR=65536
CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
CONFIG_MEMORY_FAILURE=y
# CONFIG_HWPOISON_INJECT is not set
# CONFIG_TRANSPARENT_HUGEPAGE is not set
CONFIG_CLEANCACHE=y
CONFIG_FRONTSWAP=y
# CONFIG_CMA is not set
# CONFIG_ZSWAP is not set
# CONFIG_ZPOOL is not set
# CONFIG_ZBUD is not set
# CONFIG_ZSMALLOC is not set
CONFIG_GENERIC_EARLY_IOREMAP=y
CONFIG_ARCH_SUPPORTS_DEFERRED_STRUCT_PAGE_INIT=y
# CONFIG_IDLE_PAGE_TRACKING is not set
# CONFIG_X86_PMEM_LEGACY is not set
CONFIG_X86_CHECK_BIOS_CORRUPTION=y
CONFIG_X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK=y
CONFIG_X86_RESERVE_LOW=64
# CONFIG_MTRR is not set
CONFIG_ARCH_RANDOM=y
CONFIG_X86_SMAP=y
# CONFIG_X86_INTEL_MPX is not set
# CONFIG_EFI is not set
CONFIG_SECCOMP=y
CONFIG_HZ_100=y
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=100
CONFIG_SCHED_HRTICK=y
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
CONFIG_RELOCATABLE=y
# CONFIG_RANDOMIZE_BASE is not set
CONFIG_PHYSICAL_ALIGN=0x1000000
CONFIG_HOTPLUG_CPU=y
# CONFIG_BOOTPARAM_HOTPLUG_CPU0 is not set
# CONFIG_DEBUG_HOTPLUG_CPU0 is not set
CONFIG_COMPAT_VDSO=y
# CONFIG_LEGACY_VSYSCALL_NATIVE is not set
CONFIG_LEGACY_VSYSCALL_EMULATE=y
# CONFIG_LEGACY_VSYSCALL_NONE is not set
# CONFIG_CMDLINE_BOOL is not set
CONFIG_MODIFY_LDT_SYSCALL=y
CONFIG_HAVE_LIVEPATCH=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_USE_PERCPU_NUMA_NODE_ID=y
#
# Power management and ACPI options
#
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
# CONFIG_SUSPEND_SKIP_SYNC is not set
CONFIG_HIBERNATE_CALLBACKS=y
# CONFIG_HIBERNATION is not set
CONFIG_PM_SLEEP=y
CONFIG_PM_SLEEP_SMP=y
# CONFIG_PM_AUTOSLEEP is not set
# CONFIG_PM_WAKELOCKS is not set
CONFIG_PM=y
CONFIG_PM_DEBUG=y
CONFIG_PM_ADVANCED_DEBUG=y
CONFIG_PM_TEST_SUSPEND=y
CONFIG_PM_SLEEP_DEBUG=y
CONFIG_PM_TRACE=y
CONFIG_PM_TRACE_RTC=y
# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
CONFIG_ACPI=y
CONFIG_ACPI_LEGACY_TABLES_LOOKUP=y
CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC=y
CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT=y
# CONFIG_ACPI_DEBUGGER is not set
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_REV_OVERRIDE_POSSIBLE=y
# CONFIG_ACPI_EC_DEBUGFS is not set
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=m
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_DOCK=y
CONFIG_ACPI_CPU_FREQ_PSS=y
CONFIG_ACPI_PROCESSOR_IDLE=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_IPMI=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_PROCESSOR_AGGREGATOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_NUMA=y
CONFIG_ACPI_CUSTOM_DSDT_FILE=""
# CONFIG_ACPI_CUSTOM_DSDT is not set
# CONFIG_ACPI_INITRD_TABLE_OVERRIDE is not set
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_PCI_SLOT=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
CONFIG_ACPI_HOTPLUG_IOAPIC=y
# CONFIG_ACPI_SBS is not set
CONFIG_ACPI_HED=y
# CONFIG_ACPI_REDUCED_HARDWARE_ONLY is not set
# CONFIG_ACPI_NFIT is not set
CONFIG_HAVE_ACPI_APEI=y
CONFIG_HAVE_ACPI_APEI_NMI=y
# CONFIG_ACPI_APEI is not set
# CONFIG_ACPI_EXTLOG is not set
# CONFIG_PMIC_OPREGION is not set
# CONFIG_SFI is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_GOV_COMMON=y
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
#
# CPU frequency scaling drivers
#
# CONFIG_X86_INTEL_PSTATE is not set
CONFIG_X86_PCC_CPUFREQ=m
CONFIG_X86_ACPI_CPUFREQ=m
CONFIG_X86_ACPI_CPUFREQ_CPB=y
CONFIG_X86_POWERNOW_K8=m
# CONFIG_X86_AMD_FREQ_SENSITIVITY is not set
CONFIG_X86_SPEEDSTEP_CENTRINO=m
CONFIG_X86_P4_CLOCKMOD=m
#
# shared options
#
CONFIG_X86_SPEEDSTEP_LIB=m
#
# CPU Idle
#
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
# CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set
CONFIG_INTEL_IDLE=y
#
# Memory power savings
#
CONFIG_I7300_IDLE_IOAT_CHANNEL=y
CONFIG_I7300_IDLE=y
#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_XEN=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCI_CNB20LE_QUIRK is not set
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
# CONFIG_PCIE_ECRC is not set
# CONFIG_PCIEAER_INJECT is not set
CONFIG_PCIEASPM=y
# CONFIG_PCIEASPM_DEBUG is not set
CONFIG_PCIEASPM_DEFAULT=y
# CONFIG_PCIEASPM_POWERSAVE is not set
# CONFIG_PCIEASPM_PERFORMANCE is not set
CONFIG_PCIE_PME=y
CONFIG_PCI_BUS_ADDR_T_64BIT=y
CONFIG_PCI_MSI=y
CONFIG_PCI_MSI_IRQ_DOMAIN=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCI_REALLOC_ENABLE_AUTO is not set
CONFIG_PCI_STUB=m
CONFIG_XEN_PCIDEV_FRONTEND=y
CONFIG_HT_IRQ=y
CONFIG_PCI_ATS=y
CONFIG_PCI_IOV=y
CONFIG_PCI_PRI=y
CONFIG_PCI_PASID=y
CONFIG_PCI_LABEL=y
#
# PCI host controller drivers
#
CONFIG_ISA_DMA_API=y
CONFIG_AMD_NB=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_RAPIDIO is not set
# CONFIG_X86_SYSFB is not set
#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_COMPAT_BINFMT_ELF=y
CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
CONFIG_BINFMT_SCRIPT=y
# CONFIG_HAVE_AOUT is not set
CONFIG_BINFMT_MISC=m
CONFIG_COREDUMP=y
CONFIG_IA32_EMULATION=y
CONFIG_IA32_AOUT=y
CONFIG_X86_X32=y
CONFIG_COMPAT=y
CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_KEYS_COMPAT=y
CONFIG_X86_DEV_DMA_OPS=y
CONFIG_PMC_ATOM=y
CONFIG_NET=y
CONFIG_NET_INGRESS=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_DIAG is not set
CONFIG_UNIX=y
# CONFIG_UNIX_DIAG is not set
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_ROUTE_CLASSID=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
# CONFIG_NET_IPGRE_DEMUX is not set
CONFIG_NET_IP_TUNNEL=y
CONFIG_SYN_COOKIES=y
CONFIG_NET_UDP_TUNNEL=m
# CONFIG_NET_FOU is not set
# CONFIG_NET_FOU_IP_TUNNELS is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
CONFIG_INET_TUNNEL=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
CONFIG_INET_LRO=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_INET_UDP_DIAG is not set
CONFIG_TCP_CONG_ADVANCED=y
CONFIG_TCP_CONG_BIC=m
CONFIG_TCP_CONG_CUBIC=y
CONFIG_TCP_CONG_WESTWOOD=m
CONFIG_TCP_CONG_HTCP=m
CONFIG_TCP_CONG_HSTCP=m
CONFIG_TCP_CONG_HYBLA=m
CONFIG_TCP_CONG_VEGAS=m
CONFIG_TCP_CONG_SCALABLE=m
CONFIG_TCP_CONG_LP=m
CONFIG_TCP_CONG_VENO=m
CONFIG_TCP_CONG_YEAH=m
CONFIG_TCP_CONG_ILLINOIS=m
# CONFIG_TCP_CONG_DCTCP is not set
# CONFIG_TCP_CONG_CDG is not set
CONFIG_DEFAULT_CUBIC=y
# CONFIG_DEFAULT_RENO is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=y
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_IPV6_MIP6 is not set
# CONFIG_IPV6_ILA is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
CONFIG_INET6_TUNNEL=m
CONFIG_INET6_XFRM_MODE_TRANSPORT=y
CONFIG_INET6_XFRM_MODE_TUNNEL=y
CONFIG_INET6_XFRM_MODE_BEET=y
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
# CONFIG_IPV6_VTI is not set
CONFIG_IPV6_SIT=y
# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
CONFIG_IPV6_TUNNEL=m
# CONFIG_IPV6_GRE is not set
CONFIG_IPV6_MULTIPLE_TABLES=y
CONFIG_IPV6_SUBTREES=y
# CONFIG_IPV6_MROUTE is not set
CONFIG_NETWORK_SECMARK=y
CONFIG_NET_PTP_CLASSIFY=y
# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_NETFILTER_ADVANCED=y
CONFIG_BRIDGE_NETFILTER=y
#
# Core Netfilter Configuration
#
CONFIG_NETFILTER_INGRESS=y
# CONFIG_NETFILTER_NETLINK_ACCT is not set
# CONFIG_NETFILTER_NETLINK_QUEUE is not set
# CONFIG_NETFILTER_NETLINK_LOG is not set
# CONFIG_NF_CONNTRACK is not set
# CONFIG_NF_TABLES is not set
CONFIG_NETFILTER_XTABLES=m
#
# Xtables combined modules
#
# CONFIG_NETFILTER_XT_MARK is not set
#
# Xtables targets
#
# CONFIG_NETFILTER_XT_TARGET_AUDIT is not set
# CONFIG_NETFILTER_XT_TARGET_CHECKSUM is not set
# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
CONFIG_NETFILTER_XT_TARGET_HL=m
# CONFIG_NETFILTER_XT_TARGET_HMARK is not set
# CONFIG_NETFILTER_XT_TARGET_IDLETIMER is not set
# CONFIG_NETFILTER_XT_TARGET_LED is not set
# CONFIG_NETFILTER_XT_TARGET_LOG is not set
# CONFIG_NETFILTER_XT_TARGET_MARK is not set
# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set
# CONFIG_NETFILTER_XT_TARGET_TEE is not set
# CONFIG_NETFILTER_XT_TARGET_TPROXY is not set
# CONFIG_NETFILTER_XT_TARGET_SECMARK is not set
# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
#
# Xtables matches
#
# CONFIG_NETFILTER_XT_MATCH_ADDRTYPE is not set
# CONFIG_NETFILTER_XT_MATCH_BPF is not set
# CONFIG_NETFILTER_XT_MATCH_CGROUP is not set
# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
# CONFIG_NETFILTER_XT_MATCH_CPU is not set
# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
# CONFIG_NETFILTER_XT_MATCH_DEVGROUP is not set
# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
# CONFIG_NETFILTER_XT_MATCH_ECN is not set
# CONFIG_NETFILTER_XT_MATCH_ESP is not set
# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
CONFIG_NETFILTER_XT_MATCH_HL=m
# CONFIG_NETFILTER_XT_MATCH_IPCOMP is not set
# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set
# CONFIG_NETFILTER_XT_MATCH_L2TP is not set
# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set
# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set
# CONFIG_NETFILTER_XT_MATCH_MAC is not set
# CONFIG_NETFILTER_XT_MATCH_MARK is not set
# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set
# CONFIG_NETFILTER_XT_MATCH_NFACCT is not set
# CONFIG_NETFILTER_XT_MATCH_OWNER is not set
# CONFIG_NETFILTER_XT_MATCH_POLICY is not set
# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set
# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set
# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set
# CONFIG_NETFILTER_XT_MATCH_REALM is not set
# CONFIG_NETFILTER_XT_MATCH_RECENT is not set
# CONFIG_NETFILTER_XT_MATCH_SCTP is not set
# CONFIG_NETFILTER_XT_MATCH_SOCKET is not set
# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
# CONFIG_NETFILTER_XT_MATCH_STRING is not set
# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set
# CONFIG_NETFILTER_XT_MATCH_TIME is not set
# CONFIG_NETFILTER_XT_MATCH_U32 is not set
# CONFIG_IP_SET is not set
# CONFIG_IP_VS is not set
#
# IP: Netfilter Configuration
#
# CONFIG_NF_DEFRAG_IPV4 is not set
# CONFIG_NF_DUP_IPV4 is not set
# CONFIG_NF_LOG_ARP is not set
# CONFIG_NF_LOG_IPV4 is not set
CONFIG_NF_REJECT_IPV4=m
CONFIG_IP_NF_IPTABLES=m
# CONFIG_IP_NF_MATCH_AH is not set
# CONFIG_IP_NF_MATCH_ECN is not set
# CONFIG_IP_NF_MATCH_RPFILTER is not set
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
# CONFIG_IP_NF_RAW is not set
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration
#
# CONFIG_NF_DEFRAG_IPV6 is not set
# CONFIG_NF_DUP_IPV6 is not set
# CONFIG_NF_REJECT_IPV6 is not set
# CONFIG_NF_LOG_IPV6 is not set
# CONFIG_IP6_NF_IPTABLES is not set
CONFIG_BRIDGE_NF_EBTABLES=m
CONFIG_BRIDGE_EBT_BROUTE=m
CONFIG_BRIDGE_EBT_T_FILTER=m
CONFIG_BRIDGE_EBT_T_NAT=m
CONFIG_BRIDGE_EBT_802_3=m
CONFIG_BRIDGE_EBT_AMONG=m
CONFIG_BRIDGE_EBT_ARP=m
CONFIG_BRIDGE_EBT_IP=m
# CONFIG_BRIDGE_EBT_IP6 is not set
CONFIG_BRIDGE_EBT_LIMIT=m
CONFIG_BRIDGE_EBT_MARK=m
CONFIG_BRIDGE_EBT_PKTTYPE=m
CONFIG_BRIDGE_EBT_STP=m
CONFIG_BRIDGE_EBT_VLAN=m
CONFIG_BRIDGE_EBT_ARPREPLY=m
CONFIG_BRIDGE_EBT_DNAT=m
CONFIG_BRIDGE_EBT_MARK_T=m
CONFIG_BRIDGE_EBT_REDIRECT=m
CONFIG_BRIDGE_EBT_SNAT=m
CONFIG_BRIDGE_EBT_LOG=m
CONFIG_BRIDGE_EBT_NFLOG=m
# CONFIG_IP_DCCP is not set
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_OBJCNT is not set
CONFIG_SCTP_DEFAULT_COOKIE_HMAC_MD5=y
# CONFIG_SCTP_DEFAULT_COOKIE_HMAC_SHA1 is not set
# CONFIG_SCTP_DEFAULT_COOKIE_HMAC_NONE is not set
CONFIG_SCTP_COOKIE_HMAC_MD5=y
# CONFIG_SCTP_COOKIE_HMAC_SHA1 is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_L2TP is not set
CONFIG_STP=y
CONFIG_GARP=m
CONFIG_BRIDGE=y
CONFIG_BRIDGE_IGMP_SNOOPING=y
CONFIG_BRIDGE_VLAN_FILTERING=y
CONFIG_HAVE_NET_DSA=y
CONFIG_VLAN_8021Q=m
CONFIG_VLAN_8021Q_GVRP=y
# CONFIG_VLAN_8021Q_MVRP is not set
# CONFIG_DECNET is not set
CONFIG_LLC=y
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_PHONET is not set
# CONFIG_6LOWPAN is not set
# CONFIG_IEEE802154 is not set
CONFIG_NET_SCHED=y
#
# Queueing/Scheduling
#
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_HFSC=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_MULTIQ=m
CONFIG_NET_SCH_RED=m
# CONFIG_NET_SCH_SFB is not set
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_NETEM=m
CONFIG_NET_SCH_DRR=m
# CONFIG_NET_SCH_MQPRIO is not set
# CONFIG_NET_SCH_CHOKE is not set
# CONFIG_NET_SCH_QFQ is not set
# CONFIG_NET_SCH_CODEL is not set
# CONFIG_NET_SCH_FQ_CODEL is not set
# CONFIG_NET_SCH_FQ is not set
# CONFIG_NET_SCH_HHF is not set
# CONFIG_NET_SCH_PIE is not set
CONFIG_NET_SCH_INGRESS=m
# CONFIG_NET_SCH_PLUG is not set
#
# Classification
#
CONFIG_NET_CLS=y
CONFIG_NET_CLS_BASIC=m
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
# CONFIG_CLS_U32_PERF is not set
CONFIG_CLS_U32_MARK=y
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_CLS_FLOW=m
# CONFIG_NET_CLS_CGROUP is not set
# CONFIG_NET_CLS_BPF is not set
# CONFIG_NET_CLS_FLOWER is not set
CONFIG_NET_EMATCH=y
CONFIG_NET_EMATCH_STACK=32
CONFIG_NET_EMATCH_CMP=m
CONFIG_NET_EMATCH_NBYTE=m
CONFIG_NET_EMATCH_U32=m
CONFIG_NET_EMATCH_META=m
CONFIG_NET_EMATCH_TEXT=m
CONFIG_NET_CLS_ACT=y
CONFIG_NET_ACT_POLICE=m
CONFIG_NET_ACT_GACT=m
CONFIG_GACT_PROB=y
CONFIG_NET_ACT_MIRRED=m
CONFIG_NET_ACT_IPT=m
CONFIG_NET_ACT_NAT=m
CONFIG_NET_ACT_PEDIT=m
CONFIG_NET_ACT_SIMP=m
CONFIG_NET_ACT_SKBEDIT=m
# CONFIG_NET_ACT_CSUM is not set
# CONFIG_NET_ACT_VLAN is not set
# CONFIG_NET_ACT_BPF is not set
# CONFIG_NET_CLS_IND is not set
CONFIG_NET_SCH_FIFO=y
# CONFIG_DCB is not set
CONFIG_DNS_RESOLVER=y
# CONFIG_BATMAN_ADV is not set
CONFIG_OPENVSWITCH=m
CONFIG_OPENVSWITCH_VXLAN=m
# CONFIG_VSOCKETS is not set
# CONFIG_NETLINK_MMAP is not set
# CONFIG_NETLINK_DIAG is not set
CONFIG_MPLS=y
CONFIG_NET_MPLS_GSO=m
# CONFIG_MPLS_ROUTING is not set
# CONFIG_HSR is not set
# CONFIG_NET_SWITCHDEV is not set
# CONFIG_NET_L3_MASTER_DEV is not set
CONFIG_RPS=y
CONFIG_RFS_ACCEL=y
CONFIG_XPS=y
# CONFIG_CGROUP_NET_PRIO is not set
# CONFIG_CGROUP_NET_CLASSID is not set
CONFIG_NET_RX_BUSY_POLL=y
CONFIG_BQL=y
# CONFIG_BPF_JIT is not set
CONFIG_NET_FLOW_LIMIT=y
#
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
CONFIG_FIB_RULES=y
# CONFIG_WIRELESS is not set
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_RFKILL_REGULATOR is not set
# CONFIG_NET_9P is not set
# CONFIG_CAIF is not set
# CONFIG_CEPH_LIB is not set
# CONFIG_NFC is not set
# CONFIG_LWTUNNEL is not set
CONFIG_HAVE_BPF_JIT=y
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER=y
CONFIG_UEVENT_HELPER_PATH=""
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_FIRMWARE_IN_KERNEL is not set
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set
CONFIG_ALLOW_DEV_COREDUMP=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
CONFIG_SYS_HYPERVISOR=y
# CONFIG_GENERIC_CPU_DEVICES is not set
CONFIG_GENERIC_CPU_AUTOPROBE=y
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=m
# CONFIG_DMA_SHARED_BUFFER is not set
#
# Bus devices
#
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
# CONFIG_MTD is not set
# CONFIG_OF is not set
CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
# CONFIG_PARPORT_SERIAL is not set
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_AX88796 is not set
CONFIG_PARPORT_1284=y
CONFIG_PNP=y
CONFIG_PNP_DEBUG_MESSAGES=y
#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_NULL_BLK is not set
CONFIG_BLK_DEV_FD=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_PCIESSD_MTIP32XX is not set
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_LOOP_MIN_COUNT=16
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_DRBD=m
# CONFIG_DRBD_FAULT_INJECTION is not set
CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SKD is not set
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_XEN_BLKDEV_FRONTEND is not set
CONFIG_XEN_BLKDEV_BACKEND=y
# CONFIG_BLK_DEV_HD is not set
# CONFIG_BLK_DEV_RBD is not set
# CONFIG_BLK_DEV_RSXX is not set
# CONFIG_BLK_DEV_NVME is not set
#
# Misc devices
#
# CONFIG_SENSORS_LIS3LV02D is not set
# CONFIG_AD525X_DPOT is not set
# CONFIG_DUMMY_IRQ is not set
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_HP_ILO=m
# CONFIG_APDS9802ALS is not set
# CONFIG_ISL29003 is not set
# CONFIG_ISL29020 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1780 is not set
# CONFIG_SENSORS_BH1770 is not set
# CONFIG_SENSORS_APDS990X is not set
# CONFIG_HMC6352 is not set
# CONFIG_DS1682 is not set
# CONFIG_BMP085_I2C is not set
# CONFIG_USB_SWITCH_FSA9480 is not set
# CONFIG_SRAM is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_CB710_CORE is not set
#
# Texas Instruments shared transport line discipline
#
# CONFIG_SENSORS_LIS3_I2C is not set
#
# Altera FPGA firmware download module
#
# CONFIG_ALTERA_STAPL is not set
# CONFIG_INTEL_MEI is not set
# CONFIG_INTEL_MEI_ME is not set
# CONFIG_INTEL_MEI_TXE is not set
# CONFIG_VMWARE_VMCI is not set
#
# Intel MIC Bus Driver
#
# CONFIG_INTEL_MIC_BUS is not set
#
# SCIF Bus Driver
#
# CONFIG_SCIF_BUS is not set
#
# Intel MIC Host Driver
#
#
# Intel MIC Card Driver
#
#
# SCIF Driver
#
#
# Intel MIC Coprocessor State Management (COSM) Drivers
#
# CONFIG_GENWQE is not set
# CONFIG_ECHO is not set
# CONFIG_CXL_BASE is not set
# CONFIG_CXL_KERNEL_API is not set
# CONFIG_CXL_EEH is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# SCSI device support
#
CONFIG_SCSI_MOD=y
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_NETLINK=y
# CONFIG_SCSI_MQ_DEFAULT is not set
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=m
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_SCSI_SAS_ATTRS=m
CONFIG_SCSI_SAS_LIBSAS=m
# CONFIG_SCSI_SAS_ATA is not set
CONFIG_SCSI_SAS_HOST_SMP=y
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
CONFIG_ISCSI_TCP=m
# CONFIG_ISCSI_BOOT_SYSFS is not set
# CONFIG_SCSI_CXGB3_ISCSI is not set
# CONFIG_SCSI_CXGB4_ISCSI is not set
CONFIG_SCSI_BNX2_ISCSI=m
# CONFIG_BE2ISCSI is not set
CONFIG_BLK_DEV_3W_XXXX_RAID=m
CONFIG_SCSI_HPSA=m
CONFIG_SCSI_3W_9XXX=m
CONFIG_SCSI_3W_SAS=m
CONFIG_SCSI_ACARD=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
CONFIG_SCSI_AIC79XX=m
CONFIG_AIC79XX_CMDS_PER_DEVICE=32
CONFIG_AIC79XX_RESET_DELAY_MS=5000
CONFIG_AIC79XX_DEBUG_ENABLE=y
CONFIG_AIC79XX_DEBUG_MASK=0
CONFIG_AIC79XX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_MVUMI is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_SCSI_ESAS2R is not set
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=m
CONFIG_MEGARAID_MAILBOX=m
CONFIG_MEGARAID_LEGACY=m
CONFIG_MEGARAID_SAS=m
CONFIG_SCSI_MPT3SAS=m
CONFIG_SCSI_MPT2SAS_MAX_SGE=128
CONFIG_SCSI_MPT3SAS_MAX_SGE=128
CONFIG_SCSI_MPT2SAS=m
# CONFIG_SCSI_UFSHCD is not set
CONFIG_SCSI_HPTIOP=m
CONFIG_SCSI_BUSLOGIC=m
# CONFIG_SCSI_FLASHPOINT is not set
# CONFIG_VMWARE_PVSCSI is not set
# CONFIG_XEN_SCSI_FRONTEND is not set
# CONFIG_LIBFC is not set
# CONFIG_SCSI_SNIC is not set
# CONFIG_SCSI_DMX3191D is not set
CONFIG_SCSI_EATA=m
CONFIG_SCSI_EATA_TAGGED_QUEUE=y
CONFIG_SCSI_EATA_LINKED_COMMANDS=y
CONFIG_SCSI_EATA_MAX_TAGS=16
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_ISCI is not set
CONFIG_SCSI_IPS=m
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
CONFIG_SCSI_IPR=m
# CONFIG_SCSI_IPR_TRACE is not set
# CONFIG_SCSI_IPR_DUMP is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_WD719X is not set
CONFIG_SCSI_DEBUG=m
# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_PM8001 is not set
# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_CHELSIO_FCOE is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_ATA_ACPI=y
# CONFIG_SATA_ZPODD is not set
CONFIG_SATA_PMP=y
#
# Controllers with non-SFF native interface
#
CONFIG_SATA_AHCI=m
CONFIG_SATA_AHCI_PLATFORM=m
# CONFIG_SATA_INIC162X is not set
# CONFIG_SATA_ACARD_AHCI is not set
# CONFIG_SATA_SIL24 is not set
CONFIG_ATA_SFF=y
#
# SFF controllers with custom DMA interface
#
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_SX4 is not set
CONFIG_ATA_BMDMA=y
#
# SATA SFF controllers with BMDMA
#
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_SVW is not set
# CONFIG_SATA_ULI is not set
CONFIG_SATA_VIA=y
# CONFIG_SATA_VITESSE is not set
#
# PATA SFF controllers with BMDMA
#
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RDC is not set
CONFIG_PATA_SCH=m
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_TOSHIBA is not set
# CONFIG_PATA_TRIFLEX is not set
CONFIG_PATA_VIA=m
# CONFIG_PATA_WINBOND is not set
#
# PIO-only SFF controllers
#
# CONFIG_PATA_CMD640_PCI is not set
CONFIG_PATA_MPIIX=m
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_PLATFORM is not set
# CONFIG_PATA_RZ1000 is not set
#
# Generic fallback / legacy drivers
#
CONFIG_PATA_ACPI=m
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_LEGACY is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_MD_AUTODETECT=y
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=y
CONFIG_MD_RAID10=m
CONFIG_MD_RAID456=m
CONFIG_MD_MULTIPATH=m
CONFIG_MD_FAULTY=m
# CONFIG_MD_CLUSTER is not set
# CONFIG_BCACHE is not set
CONFIG_BLK_DEV_DM_BUILTIN=y
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_MQ_DEFAULT is not set
# CONFIG_DM_DEBUG is not set
CONFIG_DM_BUFIO=y
CONFIG_DM_CRYPT=m
CONFIG_DM_SNAPSHOT=y
# CONFIG_DM_THIN_PROVISIONING is not set
# CONFIG_DM_CACHE is not set
# CONFIG_DM_ERA is not set
CONFIG_DM_MIRROR=y
CONFIG_DM_LOG_USERSPACE=m
# CONFIG_DM_RAID is not set
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=y
CONFIG_DM_MULTIPATH_QL=m
CONFIG_DM_MULTIPATH_ST=m
# CONFIG_DM_DELAY is not set
CONFIG_DM_UEVENT=y
# CONFIG_DM_FLAKEY is not set
# CONFIG_DM_VERITY is not set
# CONFIG_DM_SWITCH is not set
# CONFIG_DM_LOG_WRITES is not set
# CONFIG_TARGET_CORE is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=m
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=m
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=m
# CONFIG_FUSION_LOGGING is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
# CONFIG_FIREWIRE_NOSY is not set
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
CONFIG_MII=m
CONFIG_NET_CORE=y
CONFIG_BONDING=m
CONFIG_DUMMY=m
CONFIG_EQUALIZER=m
# CONFIG_NET_FC is not set
# CONFIG_IFB is not set
# CONFIG_NET_TEAM is not set
CONFIG_MACVLAN=m
CONFIG_MACVTAP=m
# CONFIG_IPVLAN is not set
CONFIG_VXLAN=m
# CONFIG_GENEVE is not set
CONFIG_NETCONSOLE=m
CONFIG_NETCONSOLE_DYNAMIC=y
CONFIG_NETPOLL=y
CONFIG_NET_POLL_CONTROLLER=y
CONFIG_TUN=m
# CONFIG_TUN_VNET_CROSS_LE is not set
CONFIG_VETH=m
# CONFIG_NLMON is not set
# CONFIG_ARCNET is not set
#
# CAIF transport drivers
#
CONFIG_VHOST_NET=m
CONFIG_VHOST_RING=m
CONFIG_VHOST=m
# CONFIG_VHOST_CROSS_ENDIAN_LEGACY is not set
#
# Distributed Switch Architecture drivers
#
# CONFIG_NET_DSA_MV88E6XXX is not set
# CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set
CONFIG_ETHERNET=y
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=m
CONFIG_TYPHOON=m
CONFIG_NET_VENDOR_ADAPTEC=y
# CONFIG_ADAPTEC_STARFIRE is not set
CONFIG_NET_VENDOR_AGERE=y
# CONFIG_ET131X is not set
CONFIG_NET_VENDOR_ALTEON=y
# CONFIG_ACENIC is not set
# CONFIG_ALTERA_TSE is not set
CONFIG_NET_VENDOR_AMD=y
# CONFIG_AMD8111_ETH is not set
CONFIG_PCNET32=m
CONFIG_NET_VENDOR_ARC=y
CONFIG_NET_VENDOR_ATHEROS=y
# CONFIG_ATL2 is not set
CONFIG_ATL1=m
CONFIG_ATL1E=m
CONFIG_ATL1C=m
# CONFIG_ALX is not set
# CONFIG_NET_VENDOR_AURORA is not set
CONFIG_NET_CADENCE=y
# CONFIG_MACB is not set
CONFIG_NET_VENDOR_BROADCOM=y
# CONFIG_B44 is not set
# CONFIG_BCMGENET is not set
CONFIG_BNX2=m
CONFIG_CNIC=m
CONFIG_TIGON3=m
# CONFIG_BNX2X is not set
# CONFIG_BNXT is not set
CONFIG_NET_VENDOR_BROCADE=y
# CONFIG_BNA is not set
CONFIG_NET_VENDOR_CAVIUM=y
# CONFIG_THUNDER_NIC_PF is not set
# CONFIG_THUNDER_NIC_VF is not set
# CONFIG_THUNDER_NIC_BGX is not set
# CONFIG_LIQUIDIO is not set
CONFIG_NET_VENDOR_CHELSIO=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_CHELSIO_T4 is not set
# CONFIG_CHELSIO_T4VF is not set
CONFIG_NET_VENDOR_CISCO=y
# CONFIG_ENIC is not set
# CONFIG_CX_ECAT is not set
# CONFIG_DNET is not set
CONFIG_NET_VENDOR_DEC=y
# CONFIG_NET_TULIP is not set
CONFIG_NET_VENDOR_DLINK=y
# CONFIG_DL2K is not set
# CONFIG_SUNDANCE is not set
CONFIG_NET_VENDOR_EMULEX=y
# CONFIG_BE2NET is not set
CONFIG_NET_VENDOR_EZCHIP=y
CONFIG_NET_VENDOR_EXAR=y
# CONFIG_S2IO is not set
# CONFIG_VXGE is not set
CONFIG_NET_VENDOR_HP=y
# CONFIG_HP100 is not set
CONFIG_NET_VENDOR_INTEL=y
CONFIG_E100=m
CONFIG_E1000=m
CONFIG_E1000E=m
CONFIG_IGB=m
CONFIG_IGB_HWMON=y
CONFIG_IGB_DCA=y
CONFIG_IGBVF=m
# CONFIG_IXGB is not set
# CONFIG_IXGBE is not set
CONFIG_IXGBEVF=m
# CONFIG_I40E is not set
# CONFIG_I40EVF is not set
# CONFIG_FM10K is not set
CONFIG_NET_VENDOR_I825XX=y
# CONFIG_JME is not set
CONFIG_NET_VENDOR_MARVELL=y
# CONFIG_MVMDIO is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
CONFIG_NET_VENDOR_MELLANOX=y
# CONFIG_MLX4_EN is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_MLX5_CORE is not set
# CONFIG_MLXSW_CORE is not set
CONFIG_NET_VENDOR_MICREL=y
# CONFIG_KS8842 is not set
# CONFIG_KS8851_MLL is not set
# CONFIG_KSZ884X_PCI is not set
CONFIG_NET_VENDOR_MYRI=y
# CONFIG_MYRI10GE is not set
# CONFIG_FEALNX is not set
CONFIG_NET_VENDOR_NATSEMI=y
# CONFIG_NATSEMI is not set
# CONFIG_NS83820 is not set
CONFIG_NET_VENDOR_8390=y
CONFIG_NE2K_PCI=m
CONFIG_NET_VENDOR_NVIDIA=y
CONFIG_FORCEDETH=m
CONFIG_NET_VENDOR_OKI=y
# CONFIG_ETHOC is not set
CONFIG_NET_PACKET_ENGINE=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_NET_VENDOR_QLOGIC=y
# CONFIG_QLA3XXX is not set
# CONFIG_QLCNIC is not set
# CONFIG_QLGE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_QED is not set
CONFIG_NET_VENDOR_QUALCOMM=y
CONFIG_NET_VENDOR_REALTEK=y
# CONFIG_ATP is not set
CONFIG_8139CP=m
CONFIG_8139TOO=m
CONFIG_8139TOO_PIO=y
# CONFIG_8139TOO_TUNE_TWISTER is not set
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_R8169=m
CONFIG_NET_VENDOR_RENESAS=y
CONFIG_NET_VENDOR_RDC=y
# CONFIG_R6040 is not set
CONFIG_NET_VENDOR_ROCKER=y
CONFIG_NET_VENDOR_SAMSUNG=y
# CONFIG_SXGBE_ETH is not set
CONFIG_NET_VENDOR_SEEQ=y
CONFIG_NET_VENDOR_SILAN=y
# CONFIG_SC92031 is not set
CONFIG_NET_VENDOR_SIS=y
# CONFIG_SIS900 is not set
# CONFIG_SIS190 is not set
# CONFIG_SFC is not set
CONFIG_NET_VENDOR_SMSC=y
# CONFIG_EPIC100 is not set
# CONFIG_SMSC911X is not set
# CONFIG_SMSC9420 is not set
CONFIG_NET_VENDOR_STMICRO=y
# CONFIG_STMMAC_ETH is not set
CONFIG_NET_VENDOR_SUN=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NIU is not set
CONFIG_NET_VENDOR_SYNOPSYS=y
CONFIG_NET_VENDOR_TEHUTI=y
# CONFIG_TEHUTI is not set
CONFIG_NET_VENDOR_TI=y
# CONFIG_TI_CPSW_ALE is not set
# CONFIG_TLAN is not set
CONFIG_NET_VENDOR_VIA=y
CONFIG_VIA_RHINE=m
CONFIG_VIA_RHINE_MMIO=y
CONFIG_VIA_VELOCITY=m
CONFIG_NET_VENDOR_WIZNET=y
# CONFIG_WIZNET_W5100 is not set
# CONFIG_WIZNET_W5300 is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_NET_SB1000 is not set
CONFIG_PHYLIB=y
#
# MII PHY device drivers
#
# CONFIG_AQUANTIA_PHY is not set
# CONFIG_AT803X_PHY is not set
# CONFIG_AMD_PHY is not set
CONFIG_MARVELL_PHY=y
CONFIG_DAVICOM_PHY=y
CONFIG_QSEMI_PHY=y
CONFIG_LXT_PHY=y
CONFIG_CICADA_PHY=y
CONFIG_VITESSE_PHY=y
# CONFIG_TERANETICS_PHY is not set
CONFIG_SMSC_PHY=y
CONFIG_BCM_NET_PHYLIB=y
CONFIG_BROADCOM_PHY=y
# CONFIG_BCM7XXX_PHY is not set
# CONFIG_BCM87XX_PHY is not set
CONFIG_ICPLUS_PHY=y
CONFIG_REALTEK_PHY=y
CONFIG_NATIONAL_PHY=y
CONFIG_STE10XP=y
CONFIG_LSI_ET1011C_PHY=y
# CONFIG_MICREL_PHY is not set
# CONFIG_DP83848_PHY is not set
# CONFIG_DP83867_PHY is not set
# CONFIG_MICROCHIP_PHY is not set
CONFIG_FIXED_PHY=y
CONFIG_MDIO_BITBANG=y
# CONFIG_MDIO_OCTEON is not set
# CONFIG_MDIO_BCM_UNIMAC is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
CONFIG_SLHC=m
CONFIG_USB_NET_DRIVERS=y
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_RTL8152 is not set
# CONFIG_USB_LAN78XX is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_WLAN is not set
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#
# CONFIG_WAN is not set
# CONFIG_XEN_NETDEV_FRONTEND is not set
CONFIG_XEN_NETDEV_BACKEND=y
# CONFIG_VMXNET3 is not set
# CONFIG_FUJITSU_ES is not set
CONFIG_ISDN=y
CONFIG_ISDN_I4L=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_IPPP_FILTER=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
#
# ISDN feature submodules
#
CONFIG_ISDN_DIVERSION=m
#
# ISDN4Linux hardware drivers
#
#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=m
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8
#
# HiSax supported cards
#
CONFIG_HISAX_16_3=y
# CONFIG_HISAX_TELESPCI is not set
CONFIG_HISAX_S0BOX=y
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_DIEHLDIVA=y
CONFIG_HISAX_SEDLBAUER=y
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
CONFIG_HISAX_NICCY=y
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
CONFIG_HISAX_GAZEL=y
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
CONFIG_HISAX_HFC_SX=y
# CONFIG_HISAX_DEBUG is not set
#
# HiSax PCMCIA card service modules
#
#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=m
CONFIG_HISAX_HFCUSB=m
CONFIG_HISAX_HFC4S8S=m
# CONFIG_HISAX_FRITZ_PCIPNP is not set
#
# Active cards
#
CONFIG_ISDN_CAPI=m
CONFIG_CAPI_TRACE=y
CONFIG_ISDN_CAPI_CAPI20=m
CONFIG_ISDN_CAPI_MIDDLEWARE=y
CONFIG_ISDN_CAPI_CAPIDRV=m
# CONFIG_ISDN_CAPI_CAPIDRV_VERBOSE is not set
#
# CAPI hardware drivers
#
CONFIG_CAPI_AVM=y
CONFIG_ISDN_DRV_AVMB1_B1PCI=m
CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
CONFIG_ISDN_DRV_AVMB1_T1PCI=m
CONFIG_ISDN_DRV_AVMB1_C4=m
CONFIG_CAPI_EICON=y
CONFIG_ISDN_DIVAS=m
CONFIG_ISDN_DIVAS_BRIPCI=y
CONFIG_ISDN_DIVAS_PRIPCI=y
CONFIG_ISDN_DIVAS_DIVACAPI=m
CONFIG_ISDN_DIVAS_USERIDI=m
CONFIG_ISDN_DIVAS_MAINT=m
CONFIG_ISDN_DRV_GIGASET=m
# CONFIG_GIGASET_CAPI is not set
CONFIG_GIGASET_I4L=y
# CONFIG_GIGASET_DUMMYLL is not set
CONFIG_GIGASET_BASE=m
CONFIG_GIGASET_M105=m
CONFIG_GIGASET_M101=m
# CONFIG_GIGASET_DEBUG is not set
CONFIG_HYSDN=m
CONFIG_HYSDN_CAPI=y
CONFIG_MISDN=m
CONFIG_MISDN_DSP=m
CONFIG_MISDN_L1OIP=m
#
# mISDN hardware drivers
#
CONFIG_MISDN_HFCPCI=m
CONFIG_MISDN_HFCMULTI=m
CONFIG_MISDN_HFCUSB=m
CONFIG_MISDN_AVMFRITZ=m
CONFIG_MISDN_SPEEDFAX=m
CONFIG_MISDN_INFINEON=m
CONFIG_MISDN_W6692=m
CONFIG_MISDN_NETJET=m
CONFIG_MISDN_IPAC=m
CONFIG_MISDN_ISAR=m
CONFIG_ISDN_HDLC=m
# CONFIG_NVM is not set
#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_LEDS=y
# CONFIG_INPUT_FF_MEMLESS is not set
CONFIG_INPUT_POLLDEV=m
# CONFIG_INPUT_SPARSEKMAP is not set
# CONFIG_INPUT_MATRIXKMAP is not set
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ADP5589 is not set
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_QT1070 is not set
# CONFIG_KEYBOARD_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_TCA6416 is not set
# CONFIG_KEYBOARD_TCA8418 is not set
# CONFIG_KEYBOARD_LM8323 is not set
# CONFIG_KEYBOARD_LM8333 is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_MCS is not set
# CONFIG_KEYBOARD_MPR121 is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_CYPRESS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
CONFIG_MOUSE_PS2_ELANTECH=y
CONFIG_MOUSE_PS2_SENTELIC=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
CONFIG_MOUSE_PS2_FOCALTECH=y
# CONFIG_MOUSE_PS2_VMMOUSE is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_CYAPA is not set
# CONFIG_MOUSE_ELAN_I2C is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_MOUSE_SYNAPTICS_USB is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_CT82C710=m
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=m
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_SERIO_PS2MULT is not set
# CONFIG_SERIO_ARC_PS2 is not set
# CONFIG_USERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_TTY=y
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_VT_CONSOLE_SLEEP=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_UNIX98_PTYS=y
CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=0
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
# CONFIG_N_GSM is not set
# CONFIG_TRACE_SINK is not set
CONFIG_DEVMEM=y
# CONFIG_DEVKMEM is not set
#
# Serial drivers
#
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_DMA=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
# CONFIG_SERIAL_8250_MANY_PORTS is not set
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
# CONFIG_SERIAL_8250_RSA is not set
# CONFIG_SERIAL_8250_FSL is not set
# CONFIG_SERIAL_8250_DW is not set
# CONFIG_SERIAL_8250_RT288X is not set
# CONFIG_SERIAL_8250_FINTEK is not set
# CONFIG_SERIAL_8250_MID is not set
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_UARTLITE is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_SCCNXP is not set
# CONFIG_SERIAL_SC16IS7XX is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_ARC is not set
# CONFIG_SERIAL_RP2 is not set
# CONFIG_SERIAL_FSL_LPUART is not set
# CONFIG_TTY_PRINTK is not set
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
CONFIG_HVC_DRIVER=y
CONFIG_HVC_IRQ=y
CONFIG_HVC_XEN=y
CONFIG_HVC_XEN_FRONTEND=y
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
# CONFIG_IPMI_SI_PROBE_DEFAULTS is not set
# CONFIG_IPMI_SSIF is not set
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
CONFIG_HW_RANDOM=y
CONFIG_HW_RANDOM_TIMERIOMEM=m
CONFIG_HW_RANDOM_INTEL=m
CONFIG_HW_RANDOM_AMD=m
CONFIG_HW_RANDOM_VIA=m
CONFIG_HW_RANDOM_TPM=m
CONFIG_NVRAM=m
CONFIG_R3964=m
CONFIG_APPLICOM=m
# CONFIG_MWAVE is not set
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
# CONFIG_HPET is not set
CONFIG_HANGCHECK_TIMER=m
CONFIG_TCG_TPM=m
CONFIG_TCG_TIS=m
# CONFIG_TCG_TIS_I2C_ATMEL is not set
# CONFIG_TCG_TIS_I2C_INFINEON is not set
# CONFIG_TCG_TIS_I2C_NUVOTON is not set
CONFIG_TCG_NSC=m
CONFIG_TCG_ATMEL=m
CONFIG_TCG_INFINEON=m
# CONFIG_TCG_XEN is not set
# CONFIG_TCG_CRB is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
# CONFIG_XILLYBUS is not set
#
# I2C support
#
CONFIG_I2C=y
CONFIG_ACPI_I2C_OPREGION=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=m
# CONFIG_I2C_MUX is not set
# CONFIG_I2C_HELPER_AUTO is not set
CONFIG_I2C_SMBUS=m
#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ALGOPCA=m
#
# I2C Hardware Bus support
#
#
# PC SMBus host controller drivers
#
CONFIG_I2C_ALI1535=m
CONFIG_I2C_ALI1563=m
CONFIG_I2C_ALI15X3=m
CONFIG_I2C_AMD756=m
CONFIG_I2C_AMD756_S4882=m
CONFIG_I2C_AMD8111=m
CONFIG_I2C_I801=m
CONFIG_I2C_ISCH=m
# CONFIG_I2C_ISMT is not set
CONFIG_I2C_PIIX4=m
CONFIG_I2C_NFORCE2=m
CONFIG_I2C_NFORCE2_S4985=m
CONFIG_I2C_SIS5595=m
CONFIG_I2C_SIS630=m
CONFIG_I2C_SIS96X=m
CONFIG_I2C_VIA=m
CONFIG_I2C_VIAPRO=m
#
# ACPI drivers
#
CONFIG_I2C_SCMI=m
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_DESIGNWARE_PCI is not set
CONFIG_I2C_OCORES=m
CONFIG_I2C_PCA_PLATFORM=m
# CONFIG_I2C_PXA_PCI is not set
CONFIG_I2C_SIMTEC=m
# CONFIG_I2C_XILINX is not set
#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_DIOLAN_U2C is not set
CONFIG_I2C_PARPORT=m
CONFIG_I2C_PARPORT_LIGHT=m
# CONFIG_I2C_ROBOTFUZZ_OSIF is not set
CONFIG_I2C_TAOS_EVM=m
CONFIG_I2C_TINY_USB=m
#
# Other I2C/SMBus bus drivers
#
CONFIG_I2C_STUB=m
# CONFIG_I2C_SLAVE is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_SPI is not set
# CONFIG_SPMI is not set
# CONFIG_HSI is not set
#
# PPS support
#
CONFIG_PPS=m
# CONFIG_PPS_DEBUG is not set
#
# PPS clients support
#
# CONFIG_PPS_CLIENT_KTIMER is not set
# CONFIG_PPS_CLIENT_LDISC is not set
# CONFIG_PPS_CLIENT_PARPORT is not set
# CONFIG_PPS_CLIENT_GPIO is not set
#
# PPS generators support
#
#
# PTP clock support
#
CONFIG_PTP_1588_CLOCK=m
#
# Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks.
#
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_TEST_POWER is not set
# CONFIG_BATTERY_DS2780 is not set
# CONFIG_BATTERY_DS2781 is not set
# CONFIG_BATTERY_DS2782 is not set
# CONFIG_BATTERY_SBS is not set
# CONFIG_BATTERY_BQ27XXX is not set
# CONFIG_BATTERY_MAX17040 is not set
# CONFIG_BATTERY_MAX17042 is not set
# CONFIG_CHARGER_MAX8903 is not set
# CONFIG_CHARGER_LP8727 is not set
# CONFIG_CHARGER_MANAGER is not set
# CONFIG_CHARGER_BQ2415X is not set
# CONFIG_CHARGER_SMB347 is not set
# CONFIG_BATTERY_GAUGE_LTC2941 is not set
# CONFIG_POWER_RESET is not set
# CONFIG_POWER_AVS is not set
CONFIG_HWMON=y
CONFIG_HWMON_VID=m
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Native drivers
#
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_ABITUGURU3 is not set
CONFIG_SENSORS_AD7414=m
CONFIG_SENSORS_AD7418=m
CONFIG_SENSORS_ADM1021=m
CONFIG_SENSORS_ADM1025=m
CONFIG_SENSORS_ADM1026=m
CONFIG_SENSORS_ADM1029=m
CONFIG_SENSORS_ADM1031=m
CONFIG_SENSORS_ADM9240=m
# CONFIG_SENSORS_ADT7410 is not set
CONFIG_SENSORS_ADT7411=m
CONFIG_SENSORS_ADT7462=m
CONFIG_SENSORS_ADT7470=m
CONFIG_SENSORS_ADT7475=m
CONFIG_SENSORS_ASC7621=m
CONFIG_SENSORS_K8TEMP=m
CONFIG_SENSORS_K10TEMP=m
CONFIG_SENSORS_FAM15H_POWER=m
CONFIG_SENSORS_APPLESMC=m
CONFIG_SENSORS_ASB100=m
CONFIG_SENSORS_ATXP1=m
CONFIG_SENSORS_DS620=m
CONFIG_SENSORS_DS1621=m
# CONFIG_SENSORS_DELL_SMM is not set
CONFIG_SENSORS_I5K_AMB=m
CONFIG_SENSORS_F71805F=m
CONFIG_SENSORS_F71882FG=m
CONFIG_SENSORS_F75375S=m
CONFIG_SENSORS_FSCHMD=m
CONFIG_SENSORS_GL518SM=m
CONFIG_SENSORS_GL520SM=m
CONFIG_SENSORS_G760A=m
# CONFIG_SENSORS_G762 is not set
# CONFIG_SENSORS_HIH6130 is not set
CONFIG_SENSORS_IBMAEM=m
CONFIG_SENSORS_IBMPEX=m
# CONFIG_SENSORS_I5500 is not set
CONFIG_SENSORS_CORETEMP=m
CONFIG_SENSORS_IT87=m
CONFIG_SENSORS_JC42=m
# CONFIG_SENSORS_POWR1220 is not set
CONFIG_SENSORS_LINEAGE=m
# CONFIG_SENSORS_LTC2945 is not set
CONFIG_SENSORS_LTC4151=m
CONFIG_SENSORS_LTC4215=m
# CONFIG_SENSORS_LTC4222 is not set
CONFIG_SENSORS_LTC4245=m
# CONFIG_SENSORS_LTC4260 is not set
CONFIG_SENSORS_LTC4261=m
CONFIG_SENSORS_MAX16065=m
CONFIG_SENSORS_MAX1619=m
CONFIG_SENSORS_MAX1668=m
# CONFIG_SENSORS_MAX197 is not set
CONFIG_SENSORS_MAX6639=m
CONFIG_SENSORS_MAX6642=m
CONFIG_SENSORS_MAX6650=m
# CONFIG_SENSORS_MAX6697 is not set
# CONFIG_SENSORS_MAX31790 is not set
# CONFIG_SENSORS_HTU21 is not set
CONFIG_SENSORS_MCP3021=m
CONFIG_SENSORS_LM63=m
CONFIG_SENSORS_LM73=m
CONFIG_SENSORS_LM75=m
CONFIG_SENSORS_LM77=m
CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM80=m
CONFIG_SENSORS_LM83=m
CONFIG_SENSORS_LM85=m
CONFIG_SENSORS_LM87=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_LM92=m
CONFIG_SENSORS_LM93=m
# CONFIG_SENSORS_LM95234 is not set
CONFIG_SENSORS_LM95241=m
CONFIG_SENSORS_LM95245=m
CONFIG_SENSORS_PC87360=m
CONFIG_SENSORS_PC87427=m
CONFIG_SENSORS_NTC_THERMISTOR=m
# CONFIG_SENSORS_NCT6683 is not set
# CONFIG_SENSORS_NCT6775 is not set
# CONFIG_SENSORS_NCT7802 is not set
# CONFIG_SENSORS_NCT7904 is not set
CONFIG_SENSORS_PCF8591=m
CONFIG_PMBUS=m
CONFIG_SENSORS_PMBUS=m
CONFIG_SENSORS_ADM1275=m
CONFIG_SENSORS_LM25066=m
CONFIG_SENSORS_LTC2978=m
# CONFIG_SENSORS_LTC2978_REGULATOR is not set
CONFIG_SENSORS_MAX16064=m
# CONFIG_SENSORS_MAX20751 is not set
CONFIG_SENSORS_MAX34440=m
CONFIG_SENSORS_MAX8688=m
# CONFIG_SENSORS_TPS40422 is not set
CONFIG_SENSORS_UCD9000=m
CONFIG_SENSORS_UCD9200=m
CONFIG_SENSORS_ZL6100=m
CONFIG_SENSORS_SHT21=m
# CONFIG_SENSORS_SHTC1 is not set
CONFIG_SENSORS_SIS5595=m
CONFIG_SENSORS_DME1737=m
CONFIG_SENSORS_EMC1403=m
CONFIG_SENSORS_EMC2103=m
CONFIG_SENSORS_EMC6W201=m
CONFIG_SENSORS_SMSC47M1=m
CONFIG_SENSORS_SMSC47M192=m
CONFIG_SENSORS_SMSC47B397=m
CONFIG_SENSORS_SCH56XX_COMMON=m
CONFIG_SENSORS_SCH5627=m
CONFIG_SENSORS_SCH5636=m
CONFIG_SENSORS_SMM665=m
# CONFIG_SENSORS_ADC128D818 is not set
CONFIG_SENSORS_ADS1015=m
CONFIG_SENSORS_ADS7828=m
CONFIG_SENSORS_AMC6821=m
# CONFIG_SENSORS_INA209 is not set
# CONFIG_SENSORS_INA2XX is not set
# CONFIG_SENSORS_TC74 is not set
CONFIG_SENSORS_THMC50=m
CONFIG_SENSORS_TMP102=m
# CONFIG_SENSORS_TMP103 is not set
CONFIG_SENSORS_TMP401=m
CONFIG_SENSORS_TMP421=m
CONFIG_SENSORS_VIA_CPUTEMP=m
CONFIG_SENSORS_VIA686A=m
CONFIG_SENSORS_VT1211=m
CONFIG_SENSORS_VT8231=m
CONFIG_SENSORS_W83781D=m
CONFIG_SENSORS_W83791D=m
CONFIG_SENSORS_W83792D=m
CONFIG_SENSORS_W83793=m
CONFIG_SENSORS_W83795=m
# CONFIG_SENSORS_W83795_FANCTRL is not set
CONFIG_SENSORS_W83L785TS=m
CONFIG_SENSORS_W83L786NG=m
CONFIG_SENSORS_W83627HF=m
CONFIG_SENSORS_W83627EHF=m
#
# ACPI drivers
#
CONFIG_SENSORS_ACPI_POWER=m
CONFIG_SENSORS_ATK0110=m
CONFIG_THERMAL=y
CONFIG_THERMAL_HWMON=y
CONFIG_THERMAL_WRITABLE_TRIPS=y
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
# CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE is not set
# CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE is not set
# CONFIG_THERMAL_DEFAULT_GOV_POWER_ALLOCATOR is not set
# CONFIG_THERMAL_GOV_FAIR_SHARE is not set
CONFIG_THERMAL_GOV_STEP_WISE=y
# CONFIG_THERMAL_GOV_BANG_BANG is not set
CONFIG_THERMAL_GOV_USER_SPACE=y
# CONFIG_THERMAL_GOV_POWER_ALLOCATOR is not set
# CONFIG_THERMAL_EMULATION is not set
# CONFIG_INTEL_POWERCLAMP is not set
CONFIG_X86_PKG_TEMP_THERMAL=m
# CONFIG_INTEL_SOC_DTS_THERMAL is not set
# CONFIG_INT340X_THERMAL is not set
# CONFIG_INTEL_PCH_THERMAL is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_CORE=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Watchdog Device Drivers
#
CONFIG_SOFT_WATCHDOG=m
# CONFIG_XILINX_WATCHDOG is not set
# CONFIG_CADENCE_WATCHDOG is not set
# CONFIG_DW_WATCHDOG is not set
# CONFIG_MAX63XX_WATCHDOG is not set
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_ALIM1535_WDT=m
CONFIG_ALIM7101_WDT=m
# CONFIG_F71808E_WDT is not set
# CONFIG_SP5100_TCO is not set
CONFIG_SBC_FITPC2_WATCHDOG=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
CONFIG_IBMASR=m
CONFIG_WAFER_WDT=m
CONFIG_I6300ESB_WDT=m
# CONFIG_IE6XX_WDT is not set
CONFIG_ITCO_WDT=m
CONFIG_ITCO_VENDOR_SUPPORT=y
CONFIG_IT8712F_WDT=m
CONFIG_IT87_WDT=m
CONFIG_HP_WATCHDOG=m
CONFIG_HPWDT_NMI_DECODING=y
CONFIG_SC1200_WDT=m
CONFIG_PC87413_WDT=m
# CONFIG_NV_TCO is not set
CONFIG_60XX_WDT=m
CONFIG_CPU5_WDT=m
CONFIG_SMSC_SCH311X_WDT=m
CONFIG_SMSC37B787_WDT=m
# CONFIG_VIA_WDT is not set
CONFIG_W83627HF_WDT=m
CONFIG_W83877F_WDT=m
CONFIG_W83977F_WDT=m
CONFIG_MACHZ_WDT=m
CONFIG_SBC_EPX_C3_WATCHDOG=m
# CONFIG_BCM7038_WDT is not set
# CONFIG_XEN_WDT is not set
#
# PCI-based Watchdog Cards
#
CONFIG_PCIPCWATCHDOG=m
CONFIG_WDTPCI=m
#
# USB-based Watchdog Cards
#
CONFIG_USBPCWATCHDOG=m
CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
CONFIG_BCMA_POSSIBLE=y
#
# Broadcom specific AMBA
#
# CONFIG_BCMA is not set
#
# Multifunction device drivers
#
CONFIG_MFD_CORE=m
# CONFIG_MFD_AS3711 is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_BCM590XX is not set
# CONFIG_MFD_AXP20X is not set
# CONFIG_MFD_CROS_EC is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_MFD_DA9055 is not set
# CONFIG_MFD_DA9062 is not set
# CONFIG_MFD_DA9063 is not set
# CONFIG_MFD_DA9150 is not set
# CONFIG_MFD_DLN2 is not set
# CONFIG_MFD_MC13XXX_I2C is not set
# CONFIG_HTC_PASIC3 is not set
CONFIG_LPC_ICH=m
CONFIG_LPC_SCH=m
# CONFIG_MFD_INTEL_LPSS_ACPI is not set
# CONFIG_MFD_INTEL_LPSS_PCI is not set
# CONFIG_MFD_JANZ_CMODIO is not set
# CONFIG_MFD_KEMPLD is not set
# CONFIG_MFD_88PM800 is not set
# CONFIG_MFD_88PM805 is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_MAX14577 is not set
# CONFIG_MFD_MAX77693 is not set
# CONFIG_MFD_MAX77843 is not set
# CONFIG_MFD_MAX8907 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_MAX8997 is not set
# CONFIG_MFD_MAX8998 is not set
# CONFIG_MFD_MT6397 is not set
# CONFIG_MFD_MENF21BMC is not set
# CONFIG_MFD_VIPERBOARD is not set
# CONFIG_MFD_RETU is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_RDC321X is not set
# CONFIG_MFD_RTSX_PCI is not set
# CONFIG_MFD_RT5033 is not set
# CONFIG_MFD_RTSX_USB is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_RN5T618 is not set
# CONFIG_MFD_SEC_CORE is not set
# CONFIG_MFD_SI476X_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_SKY81452 is not set
# CONFIG_MFD_SMSC is not set
# CONFIG_ABX500_CORE is not set
# CONFIG_MFD_SYSCON is not set
# CONFIG_MFD_TI_AM335X_TSCADC is not set
# CONFIG_MFD_LP3943 is not set
# CONFIG_MFD_LP8788 is not set
# CONFIG_MFD_PALMAS is not set
# CONFIG_TPS6105X is not set
# CONFIG_TPS6507X is not set
# CONFIG_MFD_TPS65090 is not set
# CONFIG_MFD_TPS65217 is not set
# CONFIG_MFD_TPS65218 is not set
# CONFIG_MFD_TPS6586X is not set
# CONFIG_MFD_TPS80031 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_TWL6040_CORE is not set
# CONFIG_MFD_WL1273_CORE is not set
# CONFIG_MFD_LM3533 is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_VX855 is not set
# CONFIG_MFD_ARIZONA_I2C is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
CONFIG_REGULATOR_VIRTUAL_CONSUMER=m
CONFIG_REGULATOR_USERSPACE_CONSUMER=m
# CONFIG_REGULATOR_ACT8865 is not set
# CONFIG_REGULATOR_AD5398 is not set
# CONFIG_REGULATOR_DA9210 is not set
# CONFIG_REGULATOR_DA9211 is not set
# CONFIG_REGULATOR_FAN53555 is not set
# CONFIG_REGULATOR_ISL9305 is not set
# CONFIG_REGULATOR_ISL6271A is not set
CONFIG_REGULATOR_LP3971=m
# CONFIG_REGULATOR_LP3972 is not set
# CONFIG_REGULATOR_LP872X is not set
# CONFIG_REGULATOR_LP8755 is not set
# CONFIG_REGULATOR_LTC3589 is not set
CONFIG_REGULATOR_MAX1586=m
# CONFIG_REGULATOR_MAX8649 is not set
# CONFIG_REGULATOR_MAX8660 is not set
# CONFIG_REGULATOR_MAX8952 is not set
# CONFIG_REGULATOR_MAX8973 is not set
# CONFIG_REGULATOR_MT6311 is not set
# CONFIG_REGULATOR_PFUZE100 is not set
# CONFIG_REGULATOR_TPS51632 is not set
# CONFIG_REGULATOR_TPS62360 is not set
CONFIG_REGULATOR_TPS65023=m
CONFIG_REGULATOR_TPS6507X=m
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_AGP is not set
CONFIG_VGA_ARB=y
CONFIG_VGA_ARB_MAX_GPUS=16
# CONFIG_VGA_SWITCHEROO is not set
# CONFIG_DRM is not set
#
# Frame buffer Devices
#
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
# CONFIG_VGASTATE is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
# CONFIG_SOUND is not set
#
# HID support
#
CONFIG_HID=y
# CONFIG_HID_BATTERY_STRENGTH is not set
CONFIG_HIDRAW=y
# CONFIG_UHID is not set
CONFIG_HID_GENERIC=y
#
# Special HID drivers
#
# CONFIG_HID_A4TECH is not set
# CONFIG_HID_ACRUX is not set
# CONFIG_HID_APPLE is not set
# CONFIG_HID_APPLEIR is not set
# CONFIG_HID_AUREAL is not set
# CONFIG_HID_BELKIN is not set
# CONFIG_HID_BETOP_FF is not set
# CONFIG_HID_CHERRY is not set
# CONFIG_HID_CHICONY is not set
# CONFIG_HID_CORSAIR is not set
# CONFIG_HID_CYPRESS is not set
# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EMS_FF is not set
# CONFIG_HID_ELECOM is not set
# CONFIG_HID_ELO is not set
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_GEMBIRD is not set
# CONFIG_HID_GFRM is not set
# CONFIG_HID_HOLTEK is not set
# CONFIG_HID_GT683R is not set
# CONFIG_HID_KEYTOUCH is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_UCLOGIC is not set
# CONFIG_HID_WALTOP is not set
# CONFIG_HID_GYRATION is not set
# CONFIG_HID_ICADE is not set
# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LCPOWER is not set
# CONFIG_HID_LENOVO is not set
CONFIG_HID_LOGITECH=y
CONFIG_HID_LOGITECH_DJ=m
CONFIG_HID_LOGITECH_HIDPP=m
# CONFIG_LOGITECH_FF is not set
# CONFIG_LOGIRUMBLEPAD2_FF is not set
# CONFIG_LOGIG940_FF is not set
# CONFIG_LOGIWHEELS_FF is not set
# CONFIG_HID_MAGICMOUSE is not set
CONFIG_HID_MICROSOFT=y
# CONFIG_HID_MONTEREY is not set
# CONFIG_HID_MULTITOUCH is not set
# CONFIG_HID_NTRIG is not set
# CONFIG_HID_ORTEK is not set
# CONFIG_HID_PANTHERLORD is not set
# CONFIG_HID_PENMOUNT is not set
# CONFIG_HID_PETALYNX is not set
# CONFIG_HID_PICOLCD is not set
# CONFIG_HID_PLANTRONICS is not set
# CONFIG_HID_PRIMAX is not set
# CONFIG_HID_ROCCAT is not set
# CONFIG_HID_SAITEK is not set
# CONFIG_HID_SAMSUNG is not set
# CONFIG_HID_SONY is not set
# CONFIG_HID_SPEEDLINK is not set
# CONFIG_HID_STEELSERIES is not set
# CONFIG_HID_SUNPLUS is not set
# CONFIG_HID_RMI is not set
# CONFIG_HID_GREENASIA is not set
# CONFIG_HID_SMARTJOYPLUS is not set
# CONFIG_HID_TIVO is not set
# CONFIG_HID_TOPSEED is not set
# CONFIG_HID_THINGM is not set
# CONFIG_HID_THRUSTMASTER is not set
# CONFIG_HID_WACOM is not set
# CONFIG_HID_WIIMOTE is not set
# CONFIG_HID_XINMO is not set
# CONFIG_HID_ZEROPLUS is not set
# CONFIG_HID_ZYDACRON is not set
# CONFIG_HID_SENSOR_HUB is not set
#
# USB HID support
#
CONFIG_USB_HID=y
CONFIG_HID_PID=y
CONFIG_USB_HIDDEV=y
#
# I2C HID support
#
# CONFIG_I2C_HID is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEFAULT_PERSIST=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
# CONFIG_USB_ULPI_BUS is not set
# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB_CBAF is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_XHCI_HCD=m
CONFIG_USB_XHCI_PCI=m
# CONFIG_USB_XHCI_PLATFORM is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_EHCI_PCI=y
# CONFIG_USB_EHCI_HCD_PLATFORM is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_FOTG210_HCD is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_PCI=y
# CONFIG_USB_OHCI_HCD_PLATFORM is not set
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HCD_TEST_MODE is not set
#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_WDM is not set
# CONFIG_USB_TMC is not set
#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_REALTEK is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_STORAGE_ENE_UB6250 is not set
# CONFIG_USB_UAS is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USBIP_CORE is not set
# CONFIG_USB_MUSB_HDRC is not set
# CONFIG_USB_DWC3 is not set
# CONFIG_USB_DWC2 is not set
# CONFIG_USB_CHIPIDEA is not set
# CONFIG_USB_ISP1760 is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_SIMPLE is not set
# CONFIG_USB_SERIAL_AIRCABLE is not set
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP210X is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_F81232 is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_IUU is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_METRO is not set
# CONFIG_USB_SERIAL_MOS7720 is not set
# CONFIG_USB_SERIAL_MOS7840 is not set
# CONFIG_USB_SERIAL_MXUPORT is not set
# CONFIG_USB_SERIAL_NAVMAN is not set
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_OTI6858 is not set
# CONFIG_USB_SERIAL_QCAUX is not set
# CONFIG_USB_SERIAL_QUALCOMM is not set
# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OPTION is not set
# CONFIG_USB_SERIAL_OMNINET is not set
# CONFIG_USB_SERIAL_OPTICON is not set
# CONFIG_USB_SERIAL_XSENS_MT is not set
# CONFIG_USB_SERIAL_WISHBONE is not set
# CONFIG_USB_SERIAL_SSU100 is not set
# CONFIG_USB_SERIAL_QT2 is not set
# CONFIG_USB_SERIAL_DEBUG is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_EHSET_TEST_FIXTURE is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_YUREX is not set
# CONFIG_USB_EZUSB_FX2 is not set
# CONFIG_USB_HSIC_USB3503 is not set
# CONFIG_USB_LINK_LAYER_TEST is not set
# CONFIG_USB_CHAOSKEY is not set
#
# USB Physical Layer drivers
#
# CONFIG_USB_PHY is not set
# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_USB_ISP1301 is not set
# CONFIG_USB_GADGET is not set
# CONFIG_USB_LED_TRIG is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
# CONFIG_LEDS_CLASS_FLASH is not set
#
# LED drivers
#
# CONFIG_LEDS_LM3530 is not set
# CONFIG_LEDS_LM3642 is not set
CONFIG_LEDS_PCA9532=m
CONFIG_LEDS_LP3944=m
# CONFIG_LEDS_LP5521 is not set
# CONFIG_LEDS_LP5523 is not set
# CONFIG_LEDS_LP5562 is not set
# CONFIG_LEDS_LP8501 is not set
# CONFIG_LEDS_LP8860 is not set
# CONFIG_LEDS_CLEVO_MAIL is not set
CONFIG_LEDS_PCA955X=m
# CONFIG_LEDS_PCA963X is not set
# CONFIG_LEDS_REGULATOR is not set
CONFIG_LEDS_BD2802=m
# CONFIG_LEDS_INTEL_SS4200 is not set
# CONFIG_LEDS_TCA6507 is not set
# CONFIG_LEDS_TLC591XX is not set
# CONFIG_LEDS_LM355x is not set
#
# LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)
#
# CONFIG_LEDS_BLINKM is not set
#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
# CONFIG_LEDS_TRIGGER_ONESHOT is not set
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
CONFIG_LEDS_TRIGGER_BACKLIGHT=m
# CONFIG_LEDS_TRIGGER_CPU is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_LEDS_TRIGGER_TRANSIENT is not set
# CONFIG_LEDS_TRIGGER_CAMERA is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_EDAC_ATOMIC_SCRUB=y
CONFIG_EDAC_SUPPORT=y
CONFIG_EDAC=y
CONFIG_EDAC_LEGACY_SYSFS=y
# CONFIG_EDAC_DEBUG is not set
CONFIG_EDAC_DECODE_MCE=m
CONFIG_EDAC_MM_EDAC=m
# CONFIG_EDAC_AMD64 is not set
CONFIG_EDAC_E752X=m
CONFIG_EDAC_I82975X=m
CONFIG_EDAC_I3000=m
CONFIG_EDAC_I3200=m
# CONFIG_EDAC_IE31200 is not set
CONFIG_EDAC_X38=m
CONFIG_EDAC_I5400=m
# CONFIG_EDAC_I7CORE is not set
CONFIG_EDAC_I5000=m
CONFIG_EDAC_I5100=m
# CONFIG_EDAC_I7300 is not set
# CONFIG_EDAC_SBRIDGE is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
CONFIG_RTC_SYSTOHC=y
CONFIG_RTC_SYSTOHC_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set
#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_TEST=m
#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_ABB5ZES3 is not set
# CONFIG_RTC_DRV_ABX80X is not set
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1374=m
# CONFIG_RTC_DRV_DS1374_WDT is not set
CONFIG_RTC_DRV_DS1672=m
# CONFIG_RTC_DRV_DS3232 is not set
CONFIG_RTC_DRV_MAX6900=m
CONFIG_RTC_DRV_RS5C372=m
CONFIG_RTC_DRV_ISL1208=m
# CONFIG_RTC_DRV_ISL12022 is not set
# CONFIG_RTC_DRV_ISL12057 is not set
CONFIG_RTC_DRV_X1205=m
# CONFIG_RTC_DRV_PCF2127 is not set
# CONFIG_RTC_DRV_PCF8523 is not set
CONFIG_RTC_DRV_PCF8563=m
# CONFIG_RTC_DRV_PCF85063 is not set
CONFIG_RTC_DRV_PCF8583=m
CONFIG_RTC_DRV_M41T80=m
CONFIG_RTC_DRV_M41T80_WDT=y
# CONFIG_RTC_DRV_BQ32K is not set
CONFIG_RTC_DRV_S35390A=m
CONFIG_RTC_DRV_FM3130=m
CONFIG_RTC_DRV_RX8581=m
CONFIG_RTC_DRV_RX8025=m
# CONFIG_RTC_DRV_EM3027 is not set
# CONFIG_RTC_DRV_RV3029C2 is not set
# CONFIG_RTC_DRV_RV8803 is not set
#
# SPI RTC drivers
#
#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=y
CONFIG_RTC_DRV_DS1286=m
CONFIG_RTC_DRV_DS1511=m
CONFIG_RTC_DRV_DS1553=m
# CONFIG_RTC_DRV_DS1685_FAMILY is not set
CONFIG_RTC_DRV_DS1742=m
# CONFIG_RTC_DRV_DS2404 is not set
CONFIG_RTC_DRV_STK17TA8=m
CONFIG_RTC_DRV_M48T86=m
CONFIG_RTC_DRV_M48T35=m
CONFIG_RTC_DRV_M48T59=m
# CONFIG_RTC_DRV_MSM6242 is not set
CONFIG_RTC_DRV_BQ4802=m
# CONFIG_RTC_DRV_RP5C01 is not set
CONFIG_RTC_DRV_V3020=m
#
# on-CPU RTC drivers
#
#
# HID Sensor RTC drivers
#
# CONFIG_RTC_DRV_HID_SENSOR_TIME is not set
CONFIG_DMADEVICES=y
# CONFIG_DMADEVICES_DEBUG is not set
#
# DMA Devices
#
CONFIG_DMA_ENGINE=y
CONFIG_DMA_ACPI=y
# CONFIG_INTEL_IDMA64 is not set
CONFIG_INTEL_IOATDMA=m
# CONFIG_DW_DMAC is not set
# CONFIG_DW_DMAC_PCI is not set
#
# DMA Clients
#
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
CONFIG_DMA_ENGINE_RAID=y
CONFIG_DCA=m
# CONFIG_AUXDISPLAY is not set
CONFIG_UIO=m
# CONFIG_UIO_CIF is not set
# CONFIG_UIO_PDRV_GENIRQ is not set
# CONFIG_UIO_DMEM_GENIRQ is not set
# CONFIG_UIO_AEC is not set
# CONFIG_UIO_SERCOS3 is not set
# CONFIG_UIO_PCI_GENERIC is not set
# CONFIG_UIO_NETX is not set
# CONFIG_UIO_PRUSS is not set
# CONFIG_UIO_MF624 is not set
# CONFIG_VFIO is not set
CONFIG_IRQ_BYPASS_MANAGER=m
# CONFIG_VIRT_DRIVERS is not set
#
# Virtio drivers
#
# CONFIG_VIRTIO_PCI is not set
# CONFIG_VIRTIO_MMIO is not set
#
# Microsoft Hyper-V guest support
#
# CONFIG_HYPERV is not set
#
# Xen driver support
#
CONFIG_XEN_BALLOON=y
# CONFIG_XEN_SELFBALLOONING is not set
CONFIG_XEN_SCRUB_PAGES=y
CONFIG_XEN_DEV_EVTCHN=y
CONFIG_XEN_BACKEND=y
CONFIG_XENFS=y
CONFIG_XEN_COMPAT_XENFS=y
CONFIG_XEN_SYS_HYPERVISOR=y
CONFIG_XEN_XENBUS_FRONTEND=y
CONFIG_XEN_GNTDEV=y
CONFIG_XEN_GRANT_DEV_ALLOC=m
CONFIG_SWIOTLB_XEN=y
CONFIG_XEN_TMEM=m
CONFIG_XEN_PCIDEV_BACKEND=m
CONFIG_XEN_PRIVCMD=y
CONFIG_XEN_ACPI_PROCESSOR=m
CONFIG_XEN_MCE_LOG=y
CONFIG_XEN_HAVE_PVMMU=y
CONFIG_XEN_AUTO_XLATE=y
CONFIG_XEN_ACPI=y
CONFIG_XEN_SYMS=y
CONFIG_XEN_HAVE_VPMU=y
# CONFIG_STAGING is not set
# CONFIG_X86_PLATFORM_DEVICES is not set
# CONFIG_CHROME_PLATFORMS is not set
#
# Hardware Spinlock drivers
#
#
# Clock Source drivers
#
CONFIG_CLKEVT_I8253=y
CONFIG_I8253_LOCK=y
CONFIG_CLKBLD_I8253=y
# CONFIG_ATMEL_PIT is not set
# CONFIG_SH_TIMER_CMT is not set
# CONFIG_SH_TIMER_MTU2 is not set
# CONFIG_SH_TIMER_TMU is not set
# CONFIG_EM_TIMER_STI is not set
# CONFIG_MAILBOX is not set
CONFIG_IOMMU_API=y
CONFIG_IOMMU_SUPPORT=y
#
# Generic IOMMU Pagetable Support
#
CONFIG_IOMMU_IOVA=y
CONFIG_AMD_IOMMU=y
# CONFIG_AMD_IOMMU_STATS is not set
# CONFIG_AMD_IOMMU_V2 is not set
CONFIG_DMAR_TABLE=y
CONFIG_INTEL_IOMMU=y
# CONFIG_INTEL_IOMMU_SVM is not set
CONFIG_INTEL_IOMMU_DEFAULT_ON=y
CONFIG_INTEL_IOMMU_FLOPPY_WA=y
# CONFIG_IRQ_REMAP is not set
#
# Remoteproc drivers
#
# CONFIG_STE_MODEM_RPROC is not set
#
# Rpmsg drivers
#
#
# SOC (System On Chip) specific Drivers
#
# CONFIG_SUNXI_SRAM is not set
# CONFIG_SOC_TI is not set
# CONFIG_PM_DEVFREQ is not set
# CONFIG_EXTCON is not set
# CONFIG_MEMORY is not set
# CONFIG_IIO is not set
# CONFIG_NTB is not set
# CONFIG_VME_BUS is not set
# CONFIG_PWM is not set
# CONFIG_IPACK_BUS is not set
# CONFIG_RESET_CONTROLLER is not set
# CONFIG_FMC is not set
#
# PHY Subsystem
#
# CONFIG_GENERIC_PHY is not set
# CONFIG_PHY_PXA_28NM_HSIC is not set
# CONFIG_PHY_PXA_28NM_USB2 is not set
# CONFIG_BCM_KONA_USB2_PHY is not set
# CONFIG_POWERCAP is not set
# CONFIG_MCB is not set
#
# Performance monitor support
#
CONFIG_RAS=y
# CONFIG_THUNDERBOLT is not set
#
# Android
#
# CONFIG_ANDROID is not set
# CONFIG_LIBNVDIMM is not set
# CONFIG_NVMEM is not set
# CONFIG_STM is not set
# CONFIG_STM_DUMMY is not set
# CONFIG_STM_SOURCE_CONSOLE is not set
# CONFIG_INTEL_TH is not set
#
# FPGA Configuration Support
#
# CONFIG_FPGA is not set
#
# Firmware Drivers
#
CONFIG_EDD=y
CONFIG_EDD_OFF=y
CONFIG_FIRMWARE_MEMMAP=y
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
CONFIG_DMIID=y
# CONFIG_DMI_SYSFS is not set
CONFIG_DMI_SCAN_MACHINE_NON_EFI_FALLBACK=y
# CONFIG_ISCSI_IBFT_FIND is not set
# CONFIG_GOOGLE_FIRMWARE is not set
#
# File systems
#
CONFIG_DCACHE_WORD_ACCESS=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_EXT4_FS=y
CONFIG_EXT4_FS_POSIX_ACL=y
CONFIG_EXT4_FS_SECURITY=y
# CONFIG_EXT4_ENCRYPTION is not set
# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
# CONFIG_REISERFS_FS_SECURITY is not set
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
# CONFIG_JFS_SECURITY is not set
# CONFIG_JFS_DEBUG is not set
CONFIG_JFS_STATISTICS=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_POSIX_ACL=y
CONFIG_XFS_RT=y
# CONFIG_XFS_WARN is not set
# CONFIG_XFS_DEBUG is not set
CONFIG_GFS2_FS=m
CONFIG_GFS2_FS_LOCKING_DLM=y
CONFIG_OCFS2_FS=m
CONFIG_OCFS2_FS_O2CB=m
CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m
CONFIG_OCFS2_DEBUG_MASKLOG=y
# CONFIG_OCFS2_DEBUG_FS is not set
CONFIG_BTRFS_FS=m
CONFIG_BTRFS_FS_POSIX_ACL=y
# CONFIG_BTRFS_FS_CHECK_INTEGRITY is not set
# CONFIG_BTRFS_FS_RUN_SANITY_TESTS is not set
# CONFIG_BTRFS_DEBUG is not set
# CONFIG_BTRFS_ASSERT is not set
CONFIG_NILFS2_FS=m
# CONFIG_F2FS_FS is not set
# CONFIG_FS_DAX is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_EXPORTFS=y
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FANOTIFY is not set
CONFIG_QUOTA=y
CONFIG_QUOTA_NETLINK_INTERFACE=y
# CONFIG_PRINT_QUOTA_WARNING is not set
# CONFIG_QUOTA_DEBUG is not set
CONFIG_QUOTA_TREE=m
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_QUOTACTL_COMPAT=y
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=y
CONFIG_CUSE=m
# CONFIG_OVERLAY_FS is not set
#
# Caches
#
# CONFIG_FSCACHE is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
# CONFIG_PROC_CHILDREN is not set
CONFIG_KERNFS=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_TMPFS_XATTR=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=m
# CONFIG_MISC_FILESYSTEMS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V2=m
CONFIG_NFS_V3=m
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=m
# CONFIG_NFS_SWAP is not set
# CONFIG_NFS_V4_1 is not set
# CONFIG_NFS_USE_LEGACY_DNS is not set
CONFIG_NFS_USE_KERNEL_DNS=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
# CONFIG_NFSD_PNFS is not set
CONFIG_GRACE_PERIOD=m
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
# CONFIG_SUNRPC_DEBUG is not set
# CONFIG_CEPH_FS is not set
CONFIG_CIFS=m
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_CIFS_UPCALL=y
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_ACL is not set
CONFIG_CIFS_DEBUG=y
# CONFIG_CIFS_DEBUG2 is not set
CONFIG_CIFS_DFS_UPCALL=y
# CONFIG_CIFS_SMB2 is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf8"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_MAC_ROMAN is not set
# CONFIG_NLS_MAC_CELTIC is not set
# CONFIG_NLS_MAC_CENTEURO is not set
# CONFIG_NLS_MAC_CROATIAN is not set
# CONFIG_NLS_MAC_CYRILLIC is not set
# CONFIG_NLS_MAC_GAELIC is not set
# CONFIG_NLS_MAC_GREEK is not set
# CONFIG_NLS_MAC_ICELAND is not set
# CONFIG_NLS_MAC_INUIT is not set
# CONFIG_NLS_MAC_ROMANIAN is not set
# CONFIG_NLS_MAC_TURKISH is not set
CONFIG_NLS_UTF8=y
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
#
# printk and dmesg options
#
CONFIG_PRINTK_TIME=y
CONFIG_MESSAGE_LOGLEVEL_DEFAULT=4
# CONFIG_BOOT_PRINTK_DELAY is not set
#
# Compile-time checks and compiler options
#
# CONFIG_DEBUG_INFO is not set
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
CONFIG_UNUSED_SYMBOLS=y
# CONFIG_PAGE_OWNER is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_SECTION_MISMATCH is not set
CONFIG_SECTION_MISMATCH_WARN_ONLY=y
CONFIG_ARCH_WANT_FRAME_POINTERS=y
CONFIG_FRAME_POINTER=y
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_MAGIC_SYSRQ is not set
CONFIG_DEBUG_KERNEL=y
#
# Memory Debugging
#
# CONFIG_PAGE_EXTENSION is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
CONFIG_HAVE_DEBUG_KMEMLEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VIRTUAL is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
CONFIG_HAVE_ARCH_KMEMCHECK=y
# CONFIG_KMEMCHECK is not set
CONFIG_HAVE_ARCH_KASAN=y
CONFIG_DEBUG_SHIRQ=y
#
# Debug Lockups and Hangs
#
# CONFIG_LOCKUP_DETECTOR is not set
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
# CONFIG_PANIC_ON_OOPS is not set
CONFIG_PANIC_ON_OOPS_VALUE=0
CONFIG_PANIC_TIMEOUT=0
CONFIG_SCHED_DEBUG=y
CONFIG_SCHED_INFO=y
CONFIG_SCHEDSTATS=y
# CONFIG_SCHED_STACK_END_CHECK is not set
# CONFIG_DEBUG_TIMEKEEPING is not set
CONFIG_TIMER_STATS=y
#
# Lock Debugging (spinlocks, mutexes, etc...)
#
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_WW_MUTEX_SLOWPATH is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_LOCK_TORTURE_TEST is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_PI_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
#
# RCU Debugging
#
# CONFIG_PROVE_RCU is not set
# CONFIG_SPARSE_RCU_POINTER is not set
# CONFIG_TORTURE_TEST is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_RCU_CPU_STALL_TIMEOUT=60
# CONFIG_RCU_TRACE is not set
# CONFIG_RCU_EQS_DEBUG is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_NOTIFIER_ERROR_INJECTION is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_LATENCYTOP=y
CONFIG_ARCH_HAS_DEBUG_STRICT_USER_COPY_CHECKS=y
# CONFIG_DEBUG_STRICT_USER_COPY_CHECKS is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_FENTRY=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
#
# Runtime Testing
#
# CONFIG_TEST_LIST_SORT is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_RBTREE_TEST is not set
# CONFIG_INTERVAL_TREE_TEST is not set
# CONFIG_PERCPU_TEST is not set
# CONFIG_ATOMIC64_SELFTEST is not set
CONFIG_ASYNC_RAID6_TEST=m
# CONFIG_TEST_HEXDUMP is not set
# CONFIG_TEST_STRING_HELPERS is not set
# CONFIG_TEST_KSTRTOX is not set
# CONFIG_TEST_PRINTF is not set
# CONFIG_TEST_RHASHTABLE is not set
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_TEST_LKM is not set
# CONFIG_TEST_USER_COPY is not set
# CONFIG_TEST_BPF is not set
# CONFIG_TEST_FIRMWARE is not set
# CONFIG_TEST_UDELAY is not set
# CONFIG_MEMTEST is not set
# CONFIG_TEST_STATIC_KEYS is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
CONFIG_STRICT_DEVMEM=y
CONFIG_X86_VERBOSE_BOOTUP=y
CONFIG_EARLY_PRINTK=y
# CONFIG_EARLY_PRINTK_DBGP is not set
# CONFIG_X86_PTDUMP_CORE is not set
# CONFIG_X86_PTDUMP is not set
CONFIG_DEBUG_RODATA=y
# CONFIG_DEBUG_RODATA_TEST is not set
# CONFIG_DEBUG_WX is not set
# CONFIG_DEBUG_SET_MODULE_RONX is not set
# CONFIG_DEBUG_NX_TEST is not set
CONFIG_DOUBLEFAULT=y
# CONFIG_DEBUG_TLBFLUSH is not set
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_IOMMU_STRESS is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
# CONFIG_IO_DELAY_0X80 is not set
CONFIG_IO_DELAY_0XED=y
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=1
# CONFIG_CPA_DEBUG is not set
# CONFIG_OPTIMIZE_INLINING is not set
# CONFIG_DEBUG_ENTRY is not set
# CONFIG_DEBUG_NMI_SELFTEST is not set
# CONFIG_X86_DEBUG_STATIC_CPU_HAS is not set
CONFIG_X86_DEBUG_FPU=y
# CONFIG_PUNIT_ATOM_DEBUG is not set
#
# Security options
#
CONFIG_KEYS=y
# CONFIG_PERSISTENT_KEYRINGS is not set
# CONFIG_BIG_KEYS is not set
# CONFIG_TRUSTED_KEYS is not set
# CONFIG_ENCRYPTED_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
# CONFIG_SECURITY is not set
CONFIG_SECURITYFS=y
# CONFIG_INTEL_TXT is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_XOR_BLOCKS=m
CONFIG_ASYNC_CORE=m
CONFIG_ASYNC_MEMCPY=m
CONFIG_ASYNC_XOR=m
CONFIG_ASYNC_PQ=m
CONFIG_ASYNC_RAID6_RECOV=m
CONFIG_CRYPTO=y
#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG=m
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_RNG_DEFAULT=m
CONFIG_CRYPTO_PCOMP=m
CONFIG_CRYPTO_PCOMP2=y
CONFIG_CRYPTO_AKCIPHER2=y
# CONFIG_CRYPTO_RSA is not set
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_USER is not set
CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_NULL2=y
# CONFIG_CRYPTO_PCRYPT is not set
CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_MCRYPTD is not set
CONFIG_CRYPTO_AUTHENC=m
CONFIG_CRYPTO_TEST=m
#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_CHACHA20POLY1305 is not set
CONFIG_CRYPTO_SEQIV=m
CONFIG_CRYPTO_ECHAINIV=m
#
# Block modes
#
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=m
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set
# CONFIG_CRYPTO_KEYWRAP is not set
#
# Hash modes
#
CONFIG_CRYPTO_CMAC=m
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_CRC32C_INTEL=m
# CONFIG_CRYPTO_CRC32 is not set
# CONFIG_CRYPTO_CRC32_PCLMUL is not set
CONFIG_CRYPTO_CRCT10DIF=y
# CONFIG_CRYPTO_CRCT10DIF_PCLMUL is not set
# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_POLY1305 is not set
# CONFIG_CRYPTO_POLY1305_X86_64 is not set
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=m
# CONFIG_CRYPTO_SHA1_SSSE3 is not set
# CONFIG_CRYPTO_SHA256_SSSE3 is not set
# CONFIG_CRYPTO_SHA512_SSSE3 is not set
# CONFIG_CRYPTO_SHA1_MB is not set
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_GHASH_CLMUL_NI_INTEL is not set
#
# Ciphers
#
CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_AES_X86_64 is not set
# CONFIG_CRYPTO_AES_NI_INTEL is not set
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_BLOWFISH_COMMON=m
# CONFIG_CRYPTO_BLOWFISH_X86_64 is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAMELLIA_X86_64 is not set
# CONFIG_CRYPTO_CAMELLIA_AESNI_AVX_X86_64 is not set
# CONFIG_CRYPTO_CAMELLIA_AESNI_AVX2_X86_64 is not set
CONFIG_CRYPTO_CAST_COMMON=m
CONFIG_CRYPTO_CAST5=m
# CONFIG_CRYPTO_CAST5_AVX_X86_64 is not set
CONFIG_CRYPTO_CAST6=m
# CONFIG_CRYPTO_CAST6_AVX_X86_64 is not set
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_DES3_EDE_X86_64 is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SALSA20_X86_64 is not set
# CONFIG_CRYPTO_CHACHA20 is not set
# CONFIG_CRYPTO_CHACHA20_X86_64 is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_SERPENT_SSE2_X86_64 is not set
# CONFIG_CRYPTO_SERPENT_AVX_X86_64 is not set
# CONFIG_CRYPTO_SERPENT_AVX2_X86_64 is not set
# CONFIG_CRYPTO_TEA is not set
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
# CONFIG_CRYPTO_TWOFISH_X86_64 is not set
# CONFIG_CRYPTO_TWOFISH_X86_64_3WAY is not set
# CONFIG_CRYPTO_TWOFISH_AVX_X86_64 is not set
#
# Compression
#
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=m
# CONFIG_CRYPTO_842 is not set
# CONFIG_CRYPTO_LZ4 is not set
# CONFIG_CRYPTO_LZ4HC is not set
#
# Random Number Generation
#
CONFIG_CRYPTO_ANSI_CPRNG=m
CONFIG_CRYPTO_DRBG_MENU=m
CONFIG_CRYPTO_DRBG_HMAC=y
# CONFIG_CRYPTO_DRBG_HASH is not set
# CONFIG_CRYPTO_DRBG_CTR is not set
CONFIG_CRYPTO_DRBG=m
CONFIG_CRYPTO_JITTERENTROPY=m
# CONFIG_CRYPTO_USER_API_HASH is not set
# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
# CONFIG_CRYPTO_USER_API_RNG is not set
# CONFIG_CRYPTO_USER_API_AEAD is not set
# CONFIG_CRYPTO_HW is not set
# CONFIG_ASYMMETRIC_KEY_TYPE is not set
#
# Certificates for signature checking
#
# CONFIG_SYSTEM_TRUSTED_KEYRING is not set
CONFIG_HAVE_KVM=y
CONFIG_HAVE_KVM_IRQCHIP=y
CONFIG_HAVE_KVM_IRQFD=y
CONFIG_HAVE_KVM_IRQ_ROUTING=y
CONFIG_HAVE_KVM_EVENTFD=y
CONFIG_KVM_APIC_ARCHITECTURE=y
CONFIG_KVM_MMIO=y
CONFIG_KVM_ASYNC_PF=y
CONFIG_HAVE_KVM_MSI=y
CONFIG_HAVE_KVM_CPU_RELAX_INTERCEPT=y
CONFIG_KVM_VFIO=y
CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT=y
CONFIG_KVM_COMPAT=y
CONFIG_HAVE_KVM_IRQ_BYPASS=y
CONFIG_VIRTUALIZATION=y
CONFIG_KVM=m
CONFIG_KVM_INTEL=m
CONFIG_KVM_AMD=m
CONFIG_KVM_DEVICE_ASSIGNMENT=y
# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
CONFIG_RAID6_PQ=m
CONFIG_BITREVERSE=y
# CONFIG_HAVE_ARCH_BITREVERSE is not set
CONFIG_RATIONAL=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_NET_UTILS=y
CONFIG_GENERIC_FIND_FIRST_BIT=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_IO=y
CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
CONFIG_ARCH_HAS_FAST_MULTIPLIER=y
CONFIG_CRC_CCITT=m
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not set
CONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
CONFIG_CRC7=m
CONFIG_LIBCRC32C=m
# CONFIG_CRC8 is not set
# CONFIG_AUDIT_ARCH_COMPAT_GENERIC is not set
# CONFIG_RANDOM32_SELFTEST is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_LZ4_DECOMPRESS=y
CONFIG_XZ_DEC=y
CONFIG_XZ_DEC_X86=y
CONFIG_XZ_DEC_POWERPC=y
CONFIG_XZ_DEC_IA64=y
CONFIG_XZ_DEC_ARM=y
CONFIG_XZ_DEC_ARMTHUMB=y
CONFIG_XZ_DEC_SPARC=y
CONFIG_XZ_DEC_BCJ=y
# CONFIG_XZ_DEC_TEST is not set
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_DECOMPRESS_XZ=y
CONFIG_DECOMPRESS_LZO=y
CONFIG_DECOMPRESS_LZ4=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_ASSOCIATIVE_ARRAY=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT_MAP=y
CONFIG_HAS_DMA=y
CONFIG_CHECK_SIGNATURE=y
CONFIG_CPU_RMAP=y
CONFIG_DQL=y
CONFIG_GLOB=y
# CONFIG_GLOB_SELFTEST is not set
CONFIG_NLATTR=y
CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
CONFIG_LRU_CACHE=m
# CONFIG_CORDIC is not set
# CONFIG_DDR is not set
CONFIG_OID_REGISTRY=m
# CONFIG_SG_SPLIT is not set
CONFIG_ARCH_HAS_SG_CHAIN=y
CONFIG_ARCH_HAS_PMEM_API=y
CONFIG_ARCH_HAS_MMIO_FLUSH=y
[-- Attachment #1.1.3: serial_out.txt --]
[-- Type: text/plain, Size: 23672 bytes --]
(XEN) Xen version 4.6.4 (@local.lipinutragen.it) (x86_64-pc-linux-gnu-gcc (Gentoo 4.9.4 p1.0, pie-0.6.4) 4.9.4) debug=n Sat Dec 24 12:42:18 CET 2016
(XEN) Latest ChangeSet: Gentoo GNU/Linux *
(XEN) Bootloader: GRUB 2.02~beta3ervisor *
(XEN) Command line: cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
(XEN) Video information: **
(XEN) VGA is text mode 80x25, font 8x16***************************************
(XEN) VBE/DDC methods: none; EDID transfer time: 1 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:ot the selected OS, `e' to edit the commands
(XEN) Found 1 MBR signaturesor a command-line.
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009d000 (usable)
(XEN) 000000000009d000 - 00000000000a0000 (reserved)4 4.4.26-gentoo-Dom0-44-r2)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000dfb80000 (usable) system
(XEN) 00000000dfb8e000 - 00000000dfb90000 type 9
(XEN) 00000000dfb90000 - 00000000dfb9e000 (ACPI data)
(XEN) 00000000dfb9e000 - 00000000dfbd0000 (ACPI NVS)
(XEN) 00000000dfbd0000 - 00000000dfbe0000 (reserved)
(XEN) 00000000dfbe8000 - 00000000f0000000 (reserved)
(XEN) 00000000fee00000 - 00000000fee01000 (reserved)
(XEN) 00000000ffb00000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 0000000320000000 (usable)
(XEN) ACPI: RSDP 000FAA70, 0024 (r2 ACPIAM)
(XEN) ACPI: XSDT DFB90100, 008C (r1 111610 XSDT1134 20101116 MSFT 97)
(XEN) ACPI: FACP DFB90290, 00F4 (r3 111610 FACP1134 20101116 MSFT 97)
(XEN) ACPI Warning (tbfadt-0464): Optional field "Pm2ControlBlock" has zero address or length: 0000000000000420/0 [20070126]
(XEN) ACPI: DSDT DFB904F0, 4E07 (r1 1ADQW 1ADQW068 68 INTL 20051117)
(XEN) ACPI: FACS DFB9E000, 0040
(XEN) ACPI: APIC DFB90390, 00C8 (r1 111610 APIC1134 20101116 MSFT 97)
(XEN) ACPI: SPCR DFB90460, 0050 (r1 111610 SPCR1134 20101116 MSFT 97)
(XEN) ACPI: MCFG DFB904B0, 003C (r1 111610 OEMMCFG 20101116 MSFT 97)
(XEN) ACPI: SSDT DFB9A4F0, 002A (r1 OEM_ID OEMTBLID 1 INTL 20051117)
(XEN) ACPI: OEMB DFB9E040, 0072 (r1 111610 OEMB1134 20101116 MSFT 97)
(XEN) ACPI: HPET DFB9A520, 0038 (r1 111610 OEMHPET 20101116 MSFT 97)
(XEN) ACPI: TCPA DFB9A560, 0032 (r1 111610 TBLOEMID 1 MSFT 97)
(XEN) ACPI: SSDT DFBB1E20, 1259 (r1 DpgPmm CpuPm 12 INTL 20051117)
(XEN) ACPI: EINJ DFB9A5A0, 0130 (r1 AMIER AMI_EINJ 20101116 MSFT 97)
(XEN) ACPI: BERT DFB9A730, 0030 (r1 AMIER AMI_BERT 20101116 MSFT 97)
(XEN) ACPI: ERST DFB9A760, 01B0 (r1 AMIER AMI_ERST 20101116 MSFT 97)
(XEN) ACPI: HEST DFB9A910, 00A8 (r1 AMIER ABC_HEST 20101116 MSFT 97)
(XEN) System RAM: 12283MB (12577908kB)
(XEN) No NUMA configuration found
(XEN) Faking a node at 0000000000000000-0000000320000000
(XEN) Domain heap initialised
(XEN) found SMP MP-table at 000ff780
(XEN) DMI present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: SLEEP INFO: pm1x_cnt[1:404,1:0], pm1x_evt[1:400,1:0]
(XEN) ACPI: wakeup_vec[dfb9e00c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
(XEN) Processor #4 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
(XEN) Processor #5 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
(XEN) Processor #6 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
(XEN) Processor #7 7:7 APIC version 20
(XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
(XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
(XEN) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24])
(XEN) IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 2 I/O APICs
(XEN) ACPI: HPET id: 0x8086a201 base: 0xfed00000
(XEN) Failed to get Error Log Address Range.
(XEN) HEST: Table parsing has been initialized
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) SMP: Allowing 8 CPUs (0 hotplug CPUs)
(XEN) IRQ limits: 48 GSI, 1504 MSI/MSI-X
(XEN) xstate_init: using cntxt_size: 0x240 and states: 0x3
(XEN) Intel machine check reporting enabled
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2493.807 MHz processor.
(XEN) Initing memory sharing.
(XEN) alt table ffff82d0802be6d0 -> ffff82d0802bfc84
(XEN) PCI: MCFG configuration 0: base e0000000 segment 0000 buses 00 - ff
(XEN) PCI: MCFG area at e0000000 reserved in E820
(XEN) PCI: Using MCFG for segment 0000 bus 00-ff
(XEN) I/O virtualisation disabled
(XEN) nr_sockets: 2
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) Platform timer is 14.318MHz HPET
(XEN) Allocated console ring of 64 KiB.
(XEN) mwait-idle: does not run on family 6 model 23
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: ASIDs disabled.
(XEN) HVM: VMX enabled
(XEN) HVM: Hardware Assisted Paging (HAP) not detected
(XEN) HVM: PVH mode not supported on this platform
(XEN) Brought up 8 CPUs
(XEN) HPET: 0 timers usable for broadcast (3 total)
(XEN) ACPI sleep modes: S3
(XEN) VPMU: disabled
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) Dom0 has maximum 816 PIRQs
(XEN) NX (Execute Disable) protection active
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x1d44000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000312000000->0000000314000000 (253134 pages to be allocated)
(XEN) Init. ramdisk: 000000031fcce000->000000031ffff6b8
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff81d44000
(XEN) Init. ramdisk: 0000000000000000->0000000000000000
(XEN) Phys-Mach map: 0000008000000000->0000008000200000
(XEN) Start info: ffffffff81d44000->ffffffff81d444b4
(XEN) Page tables: ffffffff81d45000->ffffffff81d58000
(XEN) Boot stack: ffffffff81d58000->ffffffff81d59000
(XEN) TOTAL: ffffffff80000000->ffffffff82000000
(XEN) ENTRY ADDRESS: ffffffff81aa71f0
(XEN) Dom0 has maximum 8 VCPUs
(XEN) Scrubbing Free RAM on 1 nodes using 8 CPUs
(XEN) .............done.
(XEN) Initial low memory virq threshold set at 0x4000 pages.
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xen)
(XEN) Freed 316kB init memory.
mapping kernel into physical memory
about to get started...
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.26-gentoo-Dom0-44-r2 (root@tobin) (gcc version 4.9.3 (Gentoo 4.9.3 p1.4, pie-0.6.4) ) #1 SMP Tue Oct 25 09:24:02 CEST 2016
[ 0.000000] Command line: init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.
nloopbacks=30 max_loop=128 noload=ahci
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'lazy' FPU context switches.
[ 0.000000] Released 0 page(s)
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009cfff] usable
[ 0.000000] Xen: [mem 0x000000000009d000-0x00000000000fffff] reserved
[ 0.000000] Xen: [mem 0x0000000000100000-0x0000000080062fff] usable
[ 0.000000] Xen: [mem 0x00000000dfb8e000-0x00000000dfb8ffff] type 9
[ 0.000000] Xen: [mem 0x00000000dfb90000-0x00000000dfb9dfff] ACPI data
[ 0.000000] Xen: [mem 0x00000000dfb9e000-0x00000000dfbcffff] ACPI NVS
[ 0.000000] Xen: [mem 0x00000000dfbd0000-0x00000000dfbdffff] reserved
[ 0.000000] Xen: [mem 0x00000000dfbe8000-0x00000000efffffff] reserved
[ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] Xen: [mem 0x00000000fec80000-0x00000000fec80fff] reserved
[ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[ 0.000000] Xen: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[ 0.000000] bootconsole [xenboot0] enabled
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] Hypervisor detected: Xen
[ 0.000000] e820: last_pfn = 0x80063 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] RAMDISK: [mem 0x02000000-0x02331fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000FAA70 000024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 0x00000000DFB90100 00008C (v01 111610 XSDT1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: FACP 0x00000000DFB90290 0000F4 (v03 111610 FACP1134 20101116 MSFT 00000097)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000420/0x0 (20150930/tbfadt-654)
[ 0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/Pm2ControlBlock: 0, using default 8 (20150930/tbfadt-704)
[ 0.000000] ACPI: DSDT 0x00000000DFB904F0 004E07 (v01 1ADQW 1ADQW068 00000068 INTL 20051117)
[ 0.000000] ACPI: FACS 0x00000000DFB9E000 000040
[ 0.000000] ACPI: FACS 0x00000000DFB9E000 000040
[ 0.000000] ACPI: APIC 0x00000000DFB90390 0000C8 (v01 111610 APIC1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: SPCR 0x00000000DFB90460 000050 (v01 111610 SPCR1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: MCFG 0x00000000DFB904B0 00003C (v01 111610 OEMMCFG 20101116 MSFT 00000097)
[ 0.000000] ACPI: SSDT 0x00000000DFB9A4F0 00002A (v01 OEM_ID OEMTBLID 00000001 INTL 20051117)
[ 0.000000] ACPI: OEMB 0x00000000DFB9E040 000072 (v01 111610 OEMB1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000DFB9A520 000038 (v01 111610 OEMHPET 20101116 MSFT 00000097)
[ 0.000000] ACPI: TCPA 0x00000000DFB9A560 000032 (v01 111610 TBLOEMID 00000001 MSFT 00000097)
[ 0.000000] ACPI: SSDT 0x00000000DFBB1E20 001259 (v01 DpgPmm CpuPm 00000012 INTL 20051117)
[ 0.000000] ACPI: EINJ 0x00000000DFB9A5A0 000130 (v01 AMIER AMI_EINJ 20101116 MSFT 00000097)
[ 0.000000] ACPI: BERT 0x00000000DFB9A730 000030 (v01 AMIER AMI_BERT 20101116 MSFT 00000097)
[ 0.000000] ACPI: ERST 0x00000000DFB9A760 0001B0 (v01 AMIER AMI_ERST 20101116 MSFT 00000097)
[ 0.000000] ACPI: HEST 0x00000000DFB9A910 0000A8 (v01 AMIER ABC_HEST 20101116 MSFT 00000097)
[ 0.000000] Setting APIC routing to Xen PV.
[ 0.000000] NUMA turned off
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000080062fff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x3fc0f000-0x3fc12fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x0000000080062fff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x0000000080062fff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000080062fff]
[ 0.000000] p2m virtual area at ffffc90000000000, size is 600000
[ 0.000000] Remapped 99 page(s)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] e820: [mem 0x80063000-0xdfb8dfff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on Xen
[ 0.000000] Xen version: 4.6.4 (preserve-AD)
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.000000] setup_percpu: NR_CPUS:12 nr_cpumask_bits:12 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 32 pages/cpu @ffff88003f200000 s92504 r8192 d30376 u262144
[ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes)
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 517096
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset n
etloop.nloopbacks=30 max_loop=128 noload=ahci
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] software IO TLB [mem 0x391fc000-0x3d1fc000] (64MB) mapped at [ffff8800391fc000-ffff88003d1fbfff]
[ 0.000000] Memory: 925860K/2097148K available (5475K kernel code, 570K rwdata, 2344K rodata, 992K init, 1596K bss, 1171288K reserved, 0K cma-reserved)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=12 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=8
[ 0.000000] Using NULL legacy PIC
[ 0.000000] NR_IRQS:4352 nr_irqs:896 0
[ 0.000000] xen:events: Using FIFO-based ABI
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty1] enabled
[ 0.000000] bootconsole [xenboot0] disabled
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.26-gentoo-Dom0-44-r2 (root@tobin) (gcc version 4.9.3 (Gentoo 4.9.3 p1.4, pie-0.6.4) ) #1 SMP Tue Oct 25 09:24:02 CEST 2016
[ 0.000000] Command line: init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.
nloopbacks=30 max_loop=128 noload=ahci
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'lazy' FPU context switches.
[ 0.000000] Released 0 page(s)
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009cfff] usable
[ 0.000000] Xen: [mem 0x000000000009d000-0x00000000000fffff] reserved
[ 0.000000] Xen: [mem 0x0000000000100000-0x0000000080062fff] usable
[ 0.000000] Xen: [mem 0x00000000dfb8e000-0x00000000dfb8ffff] type 9
[ 0.000000] Xen: [mem 0x00000000dfb90000-0x00000000dfb9dfff] ACPI data
[ 0.000000] Xen: [mem 0x00000000dfb9e000-0x00000000dfbcffff] ACPI NVS
[ 0.000000] Xen: [mem 0x00000000dfbd0000-0x00000000dfbdffff] reserved
[ 0.000000] Xen: [mem 0x00000000dfbe8000-0x00000000efffffff] reserved
[ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] Xen: [mem 0x00000000fec80000-0x00000000fec80fff] reserved
[ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[ 0.000000] Xen: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[ 0.000000] bootconsole [xenboot0] enabled
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] Hypervisor detected: Xen
[ 0.000000] e820: last_pfn = 0x80063 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] RAMDISK: [mem 0x02000000-0x02331fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000FAA70 000024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 0x00000000DFB90100 00008C (v01 111610 XSDT1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: FACP 0x00000000DFB90290 0000F4 (v03 111610 FACP1134 20101116 MSFT 00000097)
[ 0.000000] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000420/0x0 (20150930/tbfadt-654)
[ 0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/Pm2ControlBlock: 0, using default 8 (20150930/tbfadt-704)
[ 0.000000] ACPI: DSDT 0x00000000DFB904F0 004E07 (v01 1ADQW 1ADQW068 00000068 INTL 20051117)
[ 0.000000] ACPI: FACS 0x00000000DFB9E000 000040
[ 0.000000] ACPI: FACS 0x00000000DFB9E000 000040
[ 0.000000] ACPI: APIC 0x00000000DFB90390 0000C8 (v01 111610 APIC1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: SPCR 0x00000000DFB90460 000050 (v01 111610 SPCR1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: MCFG 0x00000000DFB904B0 00003C (v01 111610 OEMMCFG 20101116 MSFT 00000097)
[ 0.000000] ACPI: SSDT 0x00000000DFB9A4F0 00002A (v01 OEM_ID OEMTBLID 00000001 INTL 20051117)
[ 0.000000] ACPI: OEMB 0x00000000DFB9E040 000072 (v01 111610 OEMB1134 20101116 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000DFB9A520 000038 (v01 111610 OEMHPET 20101116 MSFT 00000097)
[ 0.000000] ACPI: TCPA 0x00000000DFB9A560 000032 (v01 111610 TBLOEMID 00000001 MSFT 00000097)
[ 0.000000] ACPI: SSDT 0x00000000DFBB1E20 001259 (v01 DpgPmm CpuPm 00000012 INTL 20051117)
[ 0.000000] ACPI: EINJ 0x00000000DFB9A5A0 000130 (v01 AMIER AMI_EINJ 20101116 MSFT 00000097)
[ 0.000000] ACPI: BERT 0x00000000DFB9A730 000030 (v01 AMIER AMI_BERT 20101116 MSFT 00000097)
[ 0.000000] ACPI: ERST 0x00000000DFB9A760 0001B0 (v01 AMIER AMI_ERST 20101116 MSFT 00000097)
[ 0.000000] ACPI: HEST 0x00000000DFB9A910 0000A8 (v01 AMIER ABC_HEST 20101116 MSFT 00000097)
[ 0.000000] Setting APIC routing to Xen PV.
[ 0.000000] NUMA turned off
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000080062fff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x3fc0f000-0x3fc12fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x0000000080062fff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x0000000080062fff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000080062fff]
[ 0.000000] p2m virtual area at ffffc90000000000, size is 600000
[ 0.000000] Remapped 99 page(s)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] e820: [mem 0x80063000-0xdfb8dfff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on Xen
[ 0.000000] Xen version: 4.6.4 (preserve-AD)
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.000000] setup_percpu: NR_CPUS:12 nr_cpumask_bits:12 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 32 pages/cpu @ffff88003f200000 s92504 r8192 d30376 u262144
[ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes)
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 517096
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset n
etloop.nloopbacks=30 max_loop=128 noload=ahci
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] software IO TLB [mem 0x391fc000-0x3d1fc000] (64MB) mapped at [ffff8800391fc000-ffff88003d1fbfff]
[ 0.000000] Memory: 925860K/2097148K available (5475K kernel code, 570K rwdata, 2344K rodata, 992K init, 1(XEN) Monitor-Mwait will be used to enter C1 state
(XEN) Monitor-Mwait will be used to enter C2 state
(XEN) Monitor-Mwait will be used to enter C3 state
This is xen-lipi-1.local.lipinutragen.it (Linux x86_64 4.4.26-gentoo-Dom0-44-r2) 14:47:44, on hvc0
xen-lipi-1 login: h
[-- Attachment #1.1.4: grub.cfg --]
[-- Type: application/octet-stream, Size: 24251 bytes --]
#
# DO NOT EDIT THIS FILE
#
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
#
### BEGIN /etc/grub.d/00_header ###
if [ -s $prefix/grubenv ]; then
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
}
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
}
serial --speed=9600 --unit=1 --word=8 --parity=no --stop=1
terminal_input console serial
terminal_output console serial
if [ x$feature_timeout_style = xy ] ; then
set timeout_style=menu
set timeout=10
# Fallback normal timeout code in case the timeout_style feature is
# unavailable.
else
set timeout=10
fi
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/04_bravebit ###
menuentry "Gentoo Xen, kernel bzImage_4.4.26-gentoo-Dom0-44-r2 UUID" {
load_video
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_4.4.26-gentoo-Dom0-44-r2 init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128 noload=ahci
module /boot/initramfs-genkernel-x86_64-4.4.26-gentoo-Dom0-44-r2
}
menuentry "Gentoo Xen, kernel bzImage_4.4.26-gentoo-Dom0-44-r2 DEVICE" {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_4.4.26-gentoo-Dom0-44-r2 init=/linuxrc root=/dev/ram0 real_root=/dev/sda1 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128
module /boot/initramfs-genkernel-x86_64-4.4.26-gentoo-Dom0-44-r2
}
menuentry "Gentoo Xen, kernel bzImage_4.4.6-gentoo-Dom0-44-r1 UUID" {
load_video
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_4.4.6-gentoo-Dom0-44-r1 init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128 noload=ahci
module /boot/initramfs-genkernel-x86_64-4.4.6-gentoo-Dom0-44-r1
}
menuentry "Gentoo Xen, kernel bzImage_4.4.6-gentoo-Dom0-44-r1 DEVICE" {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_4.4.6-gentoo-Dom0-44-r1 init=/linuxrc root=/dev/ram0 real_root=/dev/sda1 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128
module /boot/initramfs-genkernel-x86_64-4.4.6-gentoo-Dom0-44-r1
}
menuentry "Gentoo Xen, kernel bzImage_3.14.56-gentoo-Dom0-314-r4 UUID" {
load_video
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_3.14.56-gentoo-Dom0-314-r4 init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128 noload=ahci
module /boot/initramfs-genkernel-x86_64-3.14.56-gentoo-Dom0-314-r4
}
menuentry "Gentoo Xen, kernel bzImage_3.14.56-gentoo-Dom0-314-r4 DEVICE" {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_3.14.56-gentoo-Dom0-314-r4 init=/linuxrc root=/dev/ram0 real_root=/dev/sda1 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128
module /boot/initramfs-genkernel-x86_64-3.14.56-gentoo-Dom0-314-r4
}
menuentry "Gentoo Xen, kernel bzImage_3.4.9-xen-Dom0-r8 UUID" {
load_video
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_3.4.9-xen-Dom0-r8 init=/linuxrc root=/dev/ram0 real_root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128 noload=ahci
module /boot/initramfs-genkernel-x86_64-3.4.9-Dom0-r8
}
menuentry "Gentoo Xen, kernel bzImage_3.4.9-xen-Dom0-r8 DEVICE" {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
savedefault
multiboot /boot/xen.gz cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga
module /boot/bzImage_3.4.9-xen-Dom0-r8 init=/linuxrc root=/dev/ram0 real_root=/dev/sda1 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset netloop.nloopbacks=30 max_loop=128
module /boot/initramfs-genkernel-x86_64-3.4.9-Dom0-r8
}
### END /etc/grub.d/04_bravebit ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Gentoo GNU/Linux' --class gentoo --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
load_video
if [ "x$grub_platform" = xefi ]; then
set gfxpayload=keep
fi
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Linux 3.16.0-4-amd64 ...'
linux /boot/vmlinuz-3.16.0-4-amd64 root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.16.0-4-amd64
}
submenu 'Advanced options for Gentoo GNU/Linux' $menuentry_id_option 'gnulinux-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
menuentry 'Gentoo GNU/Linux, with Linux 3.16.0-4-amd64' --class gentoo --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-4-amd64-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
load_video
if [ "x$grub_platform" = xefi ]; then
set gfxpayload=keep
fi
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Linux 3.16.0-4-amd64 ...'
linux /boot/vmlinuz-3.16.0-4-amd64 root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.16.0-4-amd64
}
menuentry 'Gentoo GNU/Linux, with Linux 3.16.0-4-amd64 (recovery mode)' --class gentoo --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.16.0-4-amd64-recovery-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
load_video
if [ "x$grub_platform" = xefi ]; then
set gfxpayload=keep
fi
insmod gzio
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Linux 3.16.0-4-amd64 ...'
linux /boot/vmlinuz-3.16.0-4-amd64 root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro single xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
initrd /boot/initrd.img-3.16.0-4-amd64
}
}
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
menuentry 'Gentoo GNU/Linux, with Xen hypervisor' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-simple-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen xen ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
submenu 'Advanced options for Gentoo GNU/Linux (with Xen hypervisor)' $menuentry_id_option 'gnulinux-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
submenu 'Xen hypervisor, version xen' $menuentry_id_option 'xen-hypervisor-xen-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
menuentry 'Gentoo GNU/Linux, with Xen xen and Linux 3.16.0-4-amd64' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen xen ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
menuentry 'Gentoo GNU/Linux, with Xen xen and Linux 3.16.0-4-amd64 (recovery mode)' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-recovery-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen xen ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro single xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
}
submenu 'Xen hypervisor, version 4.6.4' $menuentry_id_option 'xen-hypervisor-4.6.4-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
menuentry 'Gentoo GNU/Linux, with Xen 4.6.4 and Linux 3.16.0-4-amd64' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen 4.6.4 ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen-4.6.4.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
menuentry 'Gentoo GNU/Linux, with Xen 4.6.4 and Linux 3.16.0-4-amd64 (recovery mode)' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-recovery-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen 4.6.4 ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen-4.6.4.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro single xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
}
submenu 'Xen hypervisor, version 4.6' $menuentry_id_option 'xen-hypervisor-4.6-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
menuentry 'Gentoo GNU/Linux, with Xen 4.6 and Linux 3.16.0-4-amd64' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen 4.6 ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen-4.6.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
menuentry 'Gentoo GNU/Linux, with Xen 4.6 and Linux 3.16.0-4-amd64 (recovery mode)' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-recovery-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen 4.6 ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen-4.6.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro single xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
}
submenu 'Xen hypervisor, version 4' $menuentry_id_option 'xen-hypervisor-4-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
menuentry 'Gentoo GNU/Linux, with Xen 4 and Linux 3.16.0-4-amd64' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-advanced-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen 4 ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen-4.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
menuentry 'Gentoo GNU/Linux, with Xen 4 and Linux 3.16.0-4-amd64 (recovery mode)' --class gentoo --class gnu-linux --class gnu --class os --class xen $menuentry_id_option 'xen-gnulinux-3.16.0-4-amd64-recovery-bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43' {
insmod part_gpt
insmod ext2
set root='hd0,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt1 --hint-efi=hd0,gpt1 --hint-baremetal=ahci0,gpt1 --hint='hd0,gpt1' bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
else
search --no-floppy --fs-uuid --set=root bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43
fi
echo 'Loading Xen 4 ...'
if [ "$grub_platform" = "pc" -o "$grub_platform" = "" ]; then
xen_rm_opts=
else
xen_rm_opts="no-real-mode edd=off"
fi
multiboot /boot/xen-4.gz placeholder loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga ${xen_rm_opts}
echo 'Loading Linux 3.16.0-4-amd64 ...'
module /boot/vmlinuz-3.16.0-4-amd64 placeholder root=UUID=bd2e7cdc-dbb9-4e35-8b5e-6b1c2be30f43 ro single xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset
echo 'Loading initial ramdisk ...'
module --nounzip /boot/initrd.img-3.16.0-4-amd64
}
}
}
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/39_memtest86+ ###
menuentry "memtest86+ 4.20" {
linux16 /boot/memtest86plus/memtest
}
menuentry "memtest86+ 4.20 (netbsd)" {
insmod bsd
knetbsd /boot/memtest86plus/memtest.netbsd
}
### END /etc/grub.d/39_memtest86+ ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
[-- Attachment #1.1.5: lspcivvv.txt --]
[-- Type: text/plain, Size: 63862 bytes --]
00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1)
Subsystem: Oracle/SUN 5000P Chipset Memory Controller Hub
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol+
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 2 (rev b1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=05, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f3c00000-f3dfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f3e00000-f42fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #48, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 (rev b1) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #49, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:06.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 6-7 (rev b1) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f4300000-fcbfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #50, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:07.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 (rev b1) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] MSI: Enable- Count=1/2 Maskable- 64bit-
Address: fee00000 Data: 0000
Capabilities: [6c] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #7, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #51, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
00:10.0 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset FSB Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: i5000_edac
Kernel modules: i5k_amb, i5000_edac
00:10.1 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset FSB Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: i5k_amb, i5000_edac
00:10.2 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset FSB Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel modules: i5k_amb, i5000_edac
00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset Reserved Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset Reserved Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset FBD Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1)
Subsystem: Oracle/SUN 5000 Series Chipset FBD Registers
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 106
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fcc00000-fcdfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag+ RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #32, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable+ ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: feeff00c Data: 41c0
Capabilities: [90] Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset PCI Express Root Port 1
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 09) (prog-if 00 [UHCI])
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset UHCI USB Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 09) (prog-if 00 [UHCI])
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset UHCI USB Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 (rev 09) (prog-if 00 [UHCI])
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset UHCI USB Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 20
Region 4: I/O ports at d000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 (rev 09) (prog-if 00 [UHCI])
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset UHCI USB Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 21
Region 4: I/O ports at cc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 09) (prog-if 20 [EHCI])
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset EHCI USB2 Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fdfff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fce00000-fdefffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Oracle/SUN 82801 PCI Bridge
00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 09)
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset LPC Interface Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel driver in use: lpc_ich
Kernel modules: intel_rng, lpc_ich
00:1f.1 IDE interface: Intel Corporation 631xESB/632xESB IDE Controller (rev 09) (prog-if 8a [Master SecP PriP])
Subsystem: Oracle/SUN 631xESB/632xESB IDE Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0 [size=16]
Kernel modules: pata_acpi
00:1f.2 SATA controller: Intel Corporation 631xESB/632xESB SATA AHCI Controller (rev 09) (prog-if 01 [AHCI 1.0])
Subsystem: Oracle/SUN 631xESB/632xESB SATA AHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e400 [size=8]
Region 3: I/O ports at e000 [size=4]
Region 4: I/O ports at dc00 [size=32]
Region 5: Memory at fdfffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 09)
Subsystem: Oracle/SUN 631xESB/632xESB/3100 Chipset SMBus Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 0300 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
01:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Bus: primary=01, secondary=02, subordinate=04, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f3c00000-f3cfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) Upstream Port, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Oracle/SUN 6311ESB/6321ESB PCI Express Upstream Port
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
01:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Oracle/SUN 6311ESB/6321ESB PCI Express to PCI-X Bridge
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=100MHz
Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
02:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) Downstream Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Oracle/SUN 6311ESB/6321ESB PCI Express Downstream Port E1
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
02:02.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E3 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f3c00000-f3cfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) Downstream Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Oracle/SUN 6311ESB/6321ESB PCI Express Downstream Port E3
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: pcieport
04:00.0 Ethernet controller: Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Oracle/SUN 80003ES2LAN Gigabit Ethernet Controller (Copper)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 109
Region 0: Memory at f3ce0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 9c00 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee1000c Data: 4179
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM not supported, Exit Latency L0s <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-23-8b-ff-ff-64-c3-72
Kernel driver in use: e1000e
Kernel modules: e1000e
04:00.1 Ethernet controller: Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Oracle/SUN 80003ES2LAN Gigabit Ethernet Controller (Copper)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 110
Region 0: Memory at f3cc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 9800 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee1000c Data: 4189
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM not supported, Exit Latency L0s <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-23-8b-ff-ff-64-c3-72
Kernel driver in use: e1000e
Kernel modules: e1000e
07:00.0 RAID bus controller: Adaptec AAC-RAID (rev 09)
Subsystem: Oracle/SUN Sun StorageTek SAS RAID HBA, Internal
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=2M]
Expansion ROM at f4280000 [disabled] [size=512K]
Capabilities: [98] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s <128ns, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [90] Vital Product Data
Not readable
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: aacraid
Kernel modules: aacraid
09:00.0 Ethernet controller: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller (rev 01)
Subsystem: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at fcbf8000 (64-bit, non-prefetchable) [size=32K]
Region 4: Memory at fcbf0000 (64-bit, non-prefetchable) [size=32K]
Expansion ROM at fca00000 [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable- Count=32 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=2 offset=00004000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <4us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
Capabilities: [94] Vendor Specific Information: Len=08 <?>
Capabilities: [9c] Vendor Specific Information: Len=40 <?>
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
09:00.1 Ethernet controller: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller (rev 01)
Subsystem: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at fcbe8000 (64-bit, non-prefetchable) [size=32K]
Region 4: Memory at fcbe0000 (64-bit, non-prefetchable) [size=32K]
Expansion ROM at fc900000 [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable- Count=32 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=2 offset=00004000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <4us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
Capabilities: [94] Vendor Specific Information: Len=08 <?>
Capabilities: [9c] Vendor Specific Information: Len=40 <?>
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
09:00.2 Ethernet controller: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller (rev 01)
Subsystem: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at f9000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at fcbd8000 (64-bit, non-prefetchable) [size=32K]
Region 4: Memory at fcbd0000 (64-bit, non-prefetchable) [size=32K]
Expansion ROM at fc800000 [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable- Count=32 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=2 offset=00004000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <4us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
Capabilities: [94] Vendor Specific Information: Len=08 <?>
Capabilities: [9c] Vendor Specific Information: Len=40 <?>
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
09:00.3 Ethernet controller: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller (rev 01)
Subsystem: Oracle/SUN Multithreaded 10-Gigabit Ethernet Network Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 11
Region 0: Memory at f8000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at fcbc8000 (64-bit, non-prefetchable) [size=32K]
Region 4: Memory at fcbc0000 (64-bit, non-prefetchable) [size=32K]
Expansion ROM at fc700000 [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable- Count=32 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=2 offset=00004000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <4us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 25.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x8, ASPM L0s, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive+ BWMgmt- ABWMgmt-
Capabilities: [94] Vendor Specific Information: Len=08 <?>
Capabilities: [9c] Vendor Specific Information: Len=40 <?>
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
0b:00.0 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06)
Subsystem: Oracle/SUN 82571EB Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 111
Region 0: Memory at fcde0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fcdc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ac00 [size=32]
Expansion ROM at fcda0000 [disabled] [size=128K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000feeff00c Data: 4139
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-23-8b-ff-ff-64-c3-74
Kernel driver in use: e1000e
Kernel modules: e1000e
0b:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06)
Subsystem: Oracle/SUN 82571EB Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 112
Region 0: Memory at fcd80000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fcd60000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a800 [size=32]
Expansion ROM at fcd40000 [disabled] [size=128K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000feeff00c Data: 4141
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Exit Latency L0s <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-23-8b-ff-ff-64-c3-74
Kernel driver in use: e1000e
Kernel modules: e1000e
0c:05.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (prog-if 00 [VGA controller])
Subsystem: Oracle/SUN ASPEED Graphics Family
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=8M]
Region 1: Memory at fdee0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bc00 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
[-- Attachment #1.1.6: dmidecode.txt --]
[-- Type: text/plain, Size: 23764 bytes --]
# dmidecode 2.12
SMBIOS 2.6 present.
74 structures occupying 3550 bytes.
Table at 0x0009D000.
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: American Megatrends Inc.
Version: 1ADQW068
Release Date: 11/16/2010
Address: 0xF0000
Runtime Size: 64 kB
ROM Size: 1024 kB
Characteristics:
ISA is supported
PCI is supported
PNP is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
BIOS ROM is socketed
EDD is supported
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
BIOS boot specification is supported
Targeted content distribution is supported
BIOS Revision: 8.16
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Sun Microsystems
Product Name: SUN FIRE X4150
Version: Rev 50
Serial Number: 0942QBR03E
UUID: FF200008-FFFF-FFFF-FFFF-00238B64C372
Wake-up Type: Power Switch
SKU Number: 4484743-170
Family: Server
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: Sun Microsystems
Product Name: SUN FIRE X4150
Version: Rev 50
Serial Number: 2029QTF-0903MR1AJN
Asset Tag: To Be Filled By O.E.M.
Features:
Board is a hosting board
Board is replaceable
Location In Chassis: To Be Filled By O.E.M.
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
Handle 0x0003, DMI type 3, 21 bytes
Chassis Information
Manufacturer: Sun Microsystems
Type: Rack Mount Chassis
Lock: Not Present
Version: Rev 50
Serial Number: To Be Filled By O.E.M.
Asset Tag: To Be Filled By O.E.M.
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
OEM Information: 0x00000000
Height: Unspecified
Number Of Power Cords: 1
Contained Elements: 0
Handle 0x0004, DMI type 4, 42 bytes
Processor Information
Socket Designation: CPU 1
Type: Central Processor
Family: <OUT OF SPEC>
Manufacturer: Intel
ID: 7A 06 01 00 FF FB EB BF
Version: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz
Voltage: 1.1 V
External Clock: 333 MHz
Max Speed: 2500 MHz
Current Speed: 2500 MHz
Status: Populated, Enabled
Upgrade: Socket LGA775
L1 Cache Handle: 0x0005
L2 Cache Handle: 0x0006
L3 Cache Handle: 0x0007
Serial Number: To Be Filled By O.E.M.
Asset Tag: To Be Filled By O.E.M.
Part Number: To Be Filled By O.E.M.
Core Count: 4
Core Enabled: 4
Thread Count: 4
Characteristics:
64-bit capable
Handle 0x0005, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1-Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 128 kB
Maximum Size: 128 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Parity
System Type: Data
Associativity: 8-way Set-associative
Handle 0x0006, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2-Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 12288 kB
Maximum Size: 12288 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Single-bit ECC
System Type: Unified
Associativity: Other
Handle 0x0007, DMI type 7, 19 bytes
Cache Information
Socket Designation: L3-Cache
Configuration: Disabled, Not Socketed, Level 3
Operational Mode: Unknown
Location: Internal
Installed Size: 0 kB
Maximum Size: 0 kB
Supported SRAM Types:
Unknown
Installed SRAM Type: Unknown
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0008, DMI type 4, 42 bytes
Processor Information
Socket Designation: CPU 2
Type: Central Processor
Family: <OUT OF SPEC>
Manufacturer: Intel
ID: 7A 06 01 00 FF FB EB BF
Version: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz
Voltage: 1.1 V
External Clock: 333 MHz
Max Speed: 2500 MHz
Current Speed: 2500 MHz
Status: Populated, Enabled
Upgrade: Socket LGA775
L1 Cache Handle: 0x0009
L2 Cache Handle: 0x000A
L3 Cache Handle: 0x000B
Serial Number: To Be Filled By O.E.M.
Asset Tag: To Be Filled By O.E.M.
Part Number: To Be Filled By O.E.M.
Core Count: 4
Core Enabled: 4
Thread Count: 4
Characteristics:
64-bit capable
Handle 0x0009, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1-Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 128 kB
Maximum Size: 128 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Parity
System Type: Data
Associativity: 8-way Set-associative
Handle 0x000A, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2-Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 12288 kB
Maximum Size: 12288 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Single-bit ECC
System Type: Unified
Associativity: Other
Handle 0x000B, DMI type 7, 19 bytes
Cache Information
Socket Designation: L3-Cache
Configuration: Disabled, Not Socketed, Level 3
Operational Mode: Unknown
Location: Internal
Installed Size: 0 kB
Maximum Size: 0 kB
Supported SRAM Types:
Unknown
Installed SRAM Type: Unknown
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: J17 - XDP
Internal Connector Type: Other
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: JP9 - LPC DEBUG
Internal Connector Type: Other
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x000E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: J37 - CD/DVD ROM
Internal Connector Type: Other
External Reference Designator: Not Specified
External Connector Type: None
Port Type: USB
Handle 0x000F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: JP9 - SMARTVU
Internal Connector Type: Other
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x0010, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: J44 - SATA0-3
Internal Connector Type: SAS/SATA Plug Receptacle
External Reference Designator: Not Specified
External Connector Type: None
Port Type: SATA
Handle 0x0011, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: J43 - SATA4-5
Internal Connector Type: SAS/SATA Plug Receptacle
External Reference Designator: Not Specified
External Connector Type: None
Port Type: SATA
Handle 0x0012, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: J23 - NVRAM_CLR 1-3
Internal Connector Type: Other
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x0013, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: J23 - PWRD_CLR 2-4
Internal Connector Type: Other
External Reference Designator: Not Specified
External Connector Type: None
Port Type: Other
Handle 0x0014, DMI type 9, 17 bytes
System Slot Information
Designation: SLOT0
Type: x8 PCI Express
Current Usage: Available
Length: Short
ID: 0
Characteristics:
3.3 V is provided
PME signal is supported
SMBus signal is supported
Handle 0x0015, DMI type 9, 17 bytes
System Slot Information
Designation: SLOT1
Type: x8 PCI Express
Current Usage: In Use
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
SMBus signal is supported
Bus Address: ffff:07:00.0
Handle 0x0016, DMI type 9, 17 bytes
System Slot Information
Designation: SLOT2
Type: x8 PCI Express
Current Usage: In Use
Length: Short
ID: 2
Characteristics:
3.3 V is provided
PME signal is supported
SMBus signal is supported
Bus Address: ffff:09:00.0
Handle 0x0017, DMI type 126, 17 bytes
Inactive
Handle 0x0018, DMI type 126, 17 bytes
Inactive
Handle 0x0019, DMI type 126, 17 bytes
Inactive
Handle 0x001A, DMI type 10, 6 bytes
On Board Device Information
Type: Video
Status: Enabled
Description: AST2000
Handle 0x001B, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: LAN 1 of Gilgal (Intel 82563EB)
Handle 0x001C, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: LAN 2 of Gilgal (Intel 82563EB)
Handle 0x001D, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: LAN 3 of Gilgal (Intel 82571EB)
Handle 0x001E, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: LAN 4 of Gilgal (Intel 82571EB)
Handle 0x001F, DMI type 15, 55 bytes
System Event Log
Area Length: 1008 bytes
Header Start Offset: 0x0810
Data Start Offset: 0x0810
Access Method: General-purpose non-volatile data functions
Access Address: 0x0001
Status: Valid, Not Full
Change Token: 0x00000000
Header Format: No Header
Supported Log Type Descriptors: 15
Descriptor 1: OEM-specific
Data Format 1: Multiple-event handle
Descriptor 2: OEM-specific
Data Format 2: Multiple-event handle
Descriptor 3: OEM-specific
Data Format 3: Multiple-event handle
Descriptor 4: OEM-specific
Data Format 4: Multiple-event handle
Descriptor 5: OEM-specific
Data Format 5: Multiple-event handle
Descriptor 6: OEM-specific
Data Format 6: Multiple-event handle
Descriptor 7: Single-bit ECC memory error
Data Format 7: Multiple-event handle
Descriptor 8: Multi-bit ECC memory error
Data Format 8: Multiple-event handle
Descriptor 9: Parity memory error
Data Format 9: Multiple-event
Descriptor 10: I/O channel block
Data Format 10: Multiple-event
Descriptor 11: POST error
Data Format 11: POST results bitmap
Descriptor 12: PCI parity error
Data Format 12: Multiple-event handle
Descriptor 13: PCI system error
Data Format 13: Multiple-event handle
Descriptor 14: System limit exceeded
Data Format 14: Multiple-event system management
Descriptor 15: OEM-specific
Data Format 15: POST results bitmap
Handle 0x0020, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: Multi-bit ECC
Maximum Capacity: 64 GB
Error Information Handle: Not Provided
Number Of Devices: 16
Handle 0x0021, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x002FFFFFFFF
Range Size: 12 GB
Physical Array Handle: 0x0020
Partition Width: 3
Handle 0x0022, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: FB-DIMM
Set: None
Locator: DIMM_A0
Bank Locator: A
Type: DDR2
Type Detail: Other
Speed: 667 MHz
Manufacturer: Hyundai
Serial Number: 0A076048
Asset Tag:
Part Number: HYMP125F72CP8D3-Y5
Rank: Unknown
Handle 0x0023, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x001FFFFFFFF
Range Size: 8 GB
Physical Device Handle: 0x0022
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 2
Handle 0x0024, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: FB-DIMM
Set: None
Locator: DIMM_A1
Bank Locator: A
Type: DDR2
Type Detail: Other
Speed: 667 MHz
Manufacturer: Hyundai
Serial Number: 09076048
Asset Tag:
Part Number: HYMP125F72CP8D3-Y5
Rank: Unknown
Handle 0x0025, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x001FFFFFFFF
Range Size: 8 GB
Physical Device Handle: 0x0024
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 2
Handle 0x0026, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_A2
Bank Locator: A
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0027, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x0026
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x0028, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_A3
Bank Locator: A
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0029, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x0028
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x002A, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: FB-DIMM
Set: None
Locator: DIMM_B0
Bank Locator: B
Type: DDR2
Type Detail: Other
Speed: 667 MHz
Manufacturer: Hyundai
Serial Number: 0A026048
Asset Tag:
Part Number: HYMP125F72CP8D3-Y5
Rank: Unknown
Handle 0x002B, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000FFFFFFFF
Range Size: 4 GB
Physical Device Handle: 0x002A
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 2
Handle 0x002C, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: FB-DIMM
Set: None
Locator: DIMM_B1
Bank Locator: B
Type: DDR2
Type Detail: Other
Speed: 667 MHz
Manufacturer: Hyundai
Serial Number: 09076048
Asset Tag:
Part Number: HYMP125F72CP8D3-Y5
Rank: Unknown
Handle 0x002D, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x002C
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x002E, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_B2
Bank Locator: B
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x002F, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x002E
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x0030, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_B3
Bank Locator: B
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0031, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x0030
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x0032, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: FB-DIMM
Set: None
Locator: DIMM_C0
Bank Locator: C
Type: DDR2
Type Detail: Other
Speed: 667 MHz
Manufacturer: Hyundai
Serial Number: 0A066048
Asset Tag:
Part Number: HYMP125F72CP8D3-Y5
Rank: Unknown
Handle 0x0033, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00FC0000000
Ending Address: 0x007EFFFFFFF
Range Size: 4064 GB
Physical Device Handle: 0x0032
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 2
Handle 0x0034, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_C1
Bank Locator: C
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0035, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00480000000
Ending Address: 0x000000003FF
Range Size: 4078 GB
Physical Device Handle: 0x0034
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 2
Handle 0x0036, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_C2
Bank Locator: C
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0037, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00060000000
Ending Address: 0x0080FFFFFFF
Range Size: 31488 MB
Physical Device Handle: 0x0036
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x0038, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_C3
Bank Locator: C
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0039, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00580000000
Ending Address: 0x0000FFFFFFF
Range Size: 4074 GB
Physical Device Handle: 0x0038
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x003A, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: FB-DIMM
Set: None
Locator: DIMM_D0
Bank Locator: D
Type: DDR2
Type Detail: Other
Speed: 667 MHz
Manufacturer: Hyundai
Serial Number: 09026048
Asset Tag:
Part Number: HYMP125F72CP8D3-Y5
Rank: Unknown
Handle 0x003B, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00F40000000
Ending Address: 0x0007FFFFFFF
Range Size: 4037 GB
Physical Device Handle: 0x003A
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 2
Handle 0x003C, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_D1
Bank Locator: D
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x003D, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00D80000000
Ending Address: 0x0002FFFFFFF
Range Size: 4042 GB
Physical Device Handle: 0x003C
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x003E, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_D2
Bank Locator: D
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x003F, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00800000000
Ending Address: 0x000000003FF
Range Size: 4064 GB
Physical Device Handle: 0x003E
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x0040, DMI type 17, 28 bytes
Memory Device
Array Handle: 0x0020
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: No Module Installed
Form Factor: FB-DIMM
Set: None
Locator: DIMM_D3
Bank Locator: D
Type: DDR2
Type Detail: Other
Speed: Unknown
Manufacturer: N/A
Serial Number: N/A
Asset Tag:
Part Number: N/A
Rank: Unknown
Handle 0x0041, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x0040
Memory Array Mapped Address Handle: 0x0021
Partition Row Position: 1
Interleaved Data Depth: 2
Handle 0x0042, DMI type 32, 20 bytes
System Boot Information
Status: No errors detected
Handle 0x0043, DMI type 38, 18 bytes
IPMI Device Information
Interface Type: KCS (Keyboard Control Style)
Specification Version: 2.0
I2C Slave Address: 0x10
NV Storage Device: Not Present
Base Address: 0x0000000000000CA2 (I/O)
Register Spacing: Successive Byte Boundaries
Handle 0x0044, DMI type 41, 11 bytes
Onboard Device
Reference Designation: AST2000
Type: Video
Status: Enabled
Type Instance: 0
Handle 0x0045, DMI type 41, 11 bytes
Onboard Device
Reference Designation: LAN 1 of Gilgal (Intel 82563EB)
Type: Ethernet
Status: Enabled
Type Instance: 0
Handle 0x0046, DMI type 41, 11 bytes
Onboard Device
Reference Designation: LAN 2 of Gilgal (Intel 82563EB)
Type: Ethernet
Status: Enabled
Type Instance: 0
Handle 0x0047, DMI type 41, 11 bytes
Onboard Device
Reference Designation: LAN 3 of Gilgal (Intel 82571EB)
Type: Ethernet
Status: Enabled
Type Instance: 0
Handle 0x0048, DMI type 41, 11 bytes
Onboard Device
Reference Designation: LAN 4 of Gilgal (Intel 82571EB)
Type: Ethernet
Status: Enabled
Type Instance: 0
Handle 0x0049, DMI type 127, 4 bytes
End Of Table
[-- Attachment #1.2: Message signed with OpenPGP using GPGMail --]
[-- Type: application/pgp-signature, Size: 204 bytes --]
[-- Attachment #2: Type: text/plain, Size: 127 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xen.org
https://lists.xen.org/xen-devel
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: blank screen VGA or Serial while linux boot
2016-12-28 14:17 blank screen VGA or Serial while linux boot Daniele Palumbo
@ 2016-12-29 14:49 ` Konrad Rzeszutek Wilk
2016-12-29 17:44 ` Daniele Palumbo
0 siblings, 1 reply; 4+ messages in thread
From: Konrad Rzeszutek Wilk @ 2016-12-29 14:49 UTC (permalink / raw)
To: Daniele Palumbo; +Cc: xen-devel
On Wed, Dec 28, 2016 at 03:17:20PM +0100, Daniele Palumbo wrote:
> Hi,
>
> Sorry for bothering, I am following
> https://wiki.xenproject.org/wiki/Xen_Serial_Console
> and
> http://www-archive.xenproject.org/files/xensummit_4/xensummit_linux_console_slides.pdf
>
> And as written in
> https://wiki.xenproject.org/wiki/XenParavirtOps
> Here i am writing.
>
> My goal is to have the same console output on VGA and internal serial port.
>
> I am on gentoo, with Xen 4.6.4, custom kernel.
> My kernel config is in attachment.
>
> Test hardware is a Sun x4150, with ILOm.
> Serial speed is set to 9600 bps, with console redirection (so all of the BIOS messages are shown).
>
> See an example of my output in attachment (serial_out.txt), with the following settings:
> GRUB_TERMINAL="console serial"
> GRUB_SERIAL_COMMAND="serial --speed=9600 --unit=1 --word=8 --parity=no --stop=1"
> GRUB_CMDLINE_XEN="loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga"
> GRUB_CMDLINE_LINUX="xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset"
You can remove the 'xencons' and 'console=xvc0'
> full grub.cfg in attachment.
>
>
> As by the logs I am able to see the same terminal from BIOS to the XEN multiboot.
> With xen multiboot i mean messages starting with
> "(XEN) "
> e.g.:
> (XEN) Video information:Gentoo GNU/Linux (with Xen hypervisor)
> (XEN) VGA is text mode 80x25, font 8x16
>
> I am not able to get the same message across serial _AND_ vga terminal upon boot,
> AFTER the xen multiboot.
>
> With earlyprintk=xen i see also linux messages starting with
> "[ 0.000000] "
> e.g., last line seen is
> [ 0.000000] Memory: 925860K/2097148K available (5475K kernel code, 570K rwdata, 2344K rodata, 992K init, 1
>
> After that, i can always see the login prompt in both serial and VGA output.
>
>
> About grub config, the basic stuff in /etc/default/grub is:
> """
> GRUB_TERMINAL="console serial"
> GRUB_SERIAL_COMMAND="serial --speed=9600 --unit=1 --word=8 --parity=no --stop=1"
> GRUB_CMDLINE_XEN="loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga"
> """
>
> nomodeset is not helping.
>
> Seems like hvc0 contains only serial messages.
Right, that is what you should see on the iLOM.
> Seems also that setting 2 console in linux module would have exclusive access.
> It is important to mention that i can always see grub and Xen logs in both serial and VGA device.
> ttyS0 is not present at all in the dmesg.
> # dmesg |grep tty
> [ 0.648440] 00:02: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
> #
>
> Then i have tried out the following
> # serial OK, no vga after XEN multiboot and earlyprintk
> GRUB_CMDLINE_LINUX="console=hvc0 earlyprintk=xen"
> # serial OK, no vga after XEN multiboot and earlyprintk
> GRUB_CMDLINE_LINUX="console=hvc0 earlyprintk=xen nomodeset"
> # serial OK, no vga after XEN multiboot and earlyprintk
> GRUB_CMDLINE_LINUX="console=hvc0 earlyprintk=xen nomodeset vga=791"
>
>
> # VGA OK, no serial after XEN multiboot and earlyprintk
> GRUB_CMDLINE_LINUX="console=hvc0 console=tty1 earlyprintk=xen"
>
>
> # VGA OK, no serial after XEN multiboot and earlyprintk
> GRUB_CMDLINE_LINUX="console=xvc xencons=xvc console=hvc0 console=tty0 nomodeset earlyprintk=xen"
>
> # VGA OK, no serial after XEN multiboot and earlyprintk
> GRUB_CMDLINE_LINUX="xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset"
>
> Really willing to understand how to get the proper output on both serial and VGA.
If you really really want that you can do:
CMD_CMDLINE_LINUX="console=hvc0"
GRUB_CMDLINE_XEN="console=com1,vga vga=text-80x60,keep conswitch=ax
console_to_ring"
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xen.org
https://lists.xen.org/xen-devel
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: blank screen VGA or Serial while linux boot
2016-12-29 14:49 ` Konrad Rzeszutek Wilk
@ 2016-12-29 17:44 ` Daniele Palumbo
2017-01-04 20:08 ` Konrad Rzeszutek Wilk
0 siblings, 1 reply; 4+ messages in thread
From: Daniele Palumbo @ 2016-12-29 17:44 UTC (permalink / raw)
To: Konrad Rzeszutek Wilk; +Cc: xen-devel
[-- Attachment #1.1: Type: text/plain, Size: 3911 bytes --]
Il giorno 29 dic 2016, alle ore 15:49, Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> ha scritto:
Ty for the reply Konrad,
> On Wed, Dec 28, 2016 at 03:17:20PM +0100, Daniele Palumbo wrote:
>>
>> GRUB_CMDLINE_LINUX="xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset"
> You can remove the 'xencons' and 'console=xvc0’
about the slides, what is xvc0 useful for? (a link is more then welcome)
>> Seems like hvc0 contains only serial messages.
>
> Right, that is what you should see on the iLOM.
Uhm,
https://wiki.xenproject.org/wiki/Xen_Serial_Console
Say:
Pv_ops dom0 Linux kernel is configured to use the Xen (hvc0) console. Dom0 Linux kernel console output will go to the serial console through Xen, so both Xen hypervisor and dom0 linux kernel output will go to the same serial console.
Why hvc0 should be only in serial?
>> Really willing to understand how to get the proper output on both serial and VGA.
>
> If you really really want that you can do:
>
> CMD_CMDLINE_LINUX="console=hvc0"
>
> GRUB_CMDLINE_XEN="console=com1,vga vga=text-80x60,keep conswitch=ax
> console_to_ring”
Tried.
Only kernel logs in VGA, not on iLOM.
Plus, iLOM console not responding to keyboard.
Getting lost.
Any other hint?
Thanks,
Daniele
Serial logs:
XEN) Xen version 4.6.4 (@local.lipinutragen.it) (x86_64-pc-linux-gnu-gcc (Gentoo 4.9.4 p1.0, pie-0.6.4) 4.9.4) debug=n Sat Dec 24 12:42:18 CET 2016
(XEN) Latest ChangeSet: Gentoo GNU/Linux *
(XEN) Bootloader: GRUB 2.02~beta3ervisor *
(XEN) Command line: cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga vga=text-80x60,keep conswitch=ax console_to_ring86+ 4.20 **
(XEN) Video information:*******************************************************
(XEN) VGA is text mode 80x60, font 8x8
(XEN) VBE/DDC methods: none; EDID transfer time: 1 secondshted.
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information: `c' for a command-line.
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
[...]
(XEN) NX (Execute Disable) protection active
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x1d44000
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000312000000->0000000314000000 (253134 pages to be allocated)
(XEN) Init. ramdisk: 000000031fcce000->000000031ffff6b8
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff81000000->ffffffff81d44000
(XEN) Init. ramdisk: 0000000000000000->0000000000000000
(XEN) Phys-Mach map: 0000008000000000->0000008000200000
(XEN) Start info: ffffffff81d44000->ffffffff81d444b4
(XEN) Page tables: ffffffff81d45000->ffffffff81d58000
(XEN) Boot stack: ffffffff81d58000->ffffffff81d59000
(XEN) TOTAL: ffffffff80000000->ffffffff82000000
(XEN) ENTRY ADDRESS: ffffffff81aa71f0
(XEN) Dom0 has maximum 8 VCPUs
(XEN) Scrubbing Free RAM on 1 nodes using 8 CPUs
(XEN) .............done.
(XEN) Initial low memory virq threshold set at 0x4000 pages.
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is keeping VGA console.
(XEN) *** Serial input -> Xen (type 'CTRL-a' three times to switch input to DOM0)
(XEN) Freed 316kB init memory.
mapping kernel into physical memory
about to get started...
(XEN) PCI add device 0000:00:00.0
[…]
(XEN) PCI add device 0000:0c:05.0
(XEN) Monitor-Mwait will be used to enter C1 state
(XEN) Monitor-Mwait will be used to enter C2 state
(XEN) Monitor-Mwait will be used to enter C3 state
This is hostname (Linux x86_64 4.4.26-gentoo-Dom0-44-r2) 17:38:29, on hvc0
hostname login:
[-- Attachment #1.2: Message signed with OpenPGP using GPGMail --]
[-- Type: application/pgp-signature, Size: 163 bytes --]
[-- Attachment #2: Type: text/plain, Size: 127 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xen.org
https://lists.xen.org/xen-devel
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: blank screen VGA or Serial while linux boot
2016-12-29 17:44 ` Daniele Palumbo
@ 2017-01-04 20:08 ` Konrad Rzeszutek Wilk
0 siblings, 0 replies; 4+ messages in thread
From: Konrad Rzeszutek Wilk @ 2017-01-04 20:08 UTC (permalink / raw)
To: Daniele Palumbo; +Cc: xen-devel
On Thu, Dec 29, 2016 at 06:44:00PM +0100, Daniele Palumbo wrote:
> Il giorno 29 dic 2016, alle ore 15:49, Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> ha scritto:
>
> Ty for the reply Konrad,
>
> > On Wed, Dec 28, 2016 at 03:17:20PM +0100, Daniele Palumbo wrote:
> >>
> >> GRUB_CMDLINE_LINUX="xencons=xvc console=xvc0 console=hvc0 console=tty1 earlyprintk=xen nomodeset"
> > You can remove the 'xencons' and 'console=xvc0’
>
> about the slides, what is xvc0 useful for? (a link is more then welcome)
I can't remember. It used be some driver but it never got upstreamed.
>
> >> Seems like hvc0 contains only serial messages.
> >
> > Right, that is what you should see on the iLOM.
>
> Uhm,
> https://wiki.xenproject.org/wiki/Xen_Serial_Console
> Say:
> Pv_ops dom0 Linux kernel is configured to use the Xen (hvc0) console. Dom0 Linux kernel console output will go to the serial console through Xen, so both Xen hypervisor and dom0 linux kernel output will go to the same serial console.
>
> Why hvc0 should be only in serial?
It actually just transports the characters to XEn. Xen can display
it via VGA or serial console. Usually it goes through the serial port.
>
> >> Really willing to understand how to get the proper output on both serial and VGA.
> >
> > If you really really want that you can do:
> >
> > CMD_CMDLINE_LINUX="console=hvc0"
> >
> > GRUB_CMDLINE_XEN="console=com1,vga vga=text-80x60,keep conswitch=ax
> > console_to_ring”
>
> Tried.
> Only kernel logs in VGA, not on iLOM.
>
> Plus, iLOM console not responding to keyboard.
>
> Getting lost.
>
> Any other hint?
Sorry :-(
>
> Thanks,
> Daniele
>
> Serial logs:
> XEN) Xen version 4.6.4 (@local.lipinutragen.it) (x86_64-pc-linux-gnu-gcc (Gentoo 4.9.4 p1.0, pie-0.6.4) 4.9.4) debug=n Sat Dec 24 12:42:18 CET 2016
> (XEN) Latest ChangeSet: Gentoo GNU/Linux *
> (XEN) Bootloader: GRUB 2.02~beta3ervisor *
> (XEN) Command line: cpuidle dom0_mem=1024M,max:2048M loglvl=all guest_loglvl=all com1=9600,8n1 console=com1,vga vga=text-80x60,keep conswitch=ax console_to_ring86+ 4.20 **
> (XEN) Video information:*******************************************************
> (XEN) VGA is text mode 80x60, font 8x8
> (XEN) VBE/DDC methods: none; EDID transfer time: 1 secondshted.
> (XEN) EDID info not retrieved because no DDC retrieval method detected
> (XEN) Disc information: `c' for a command-line.
> (XEN) Found 1 MBR signatures
> (XEN) Found 1 EDD information structures
> (XEN) Xen-e820 RAM map:
> [...]
> (XEN) NX (Execute Disable) protection active
> (XEN) *** LOADING DOMAIN 0 ***
> (XEN) Xen kernel: 64-bit, lsb, compat32
> (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x1d44000
> (XEN) PHYSICAL MEMORY ARRANGEMENT:
> (XEN) Dom0 alloc.: 0000000312000000->0000000314000000 (253134 pages to be allocated)
> (XEN) Init. ramdisk: 000000031fcce000->000000031ffff6b8
> (XEN) VIRTUAL MEMORY ARRANGEMENT:
> (XEN) Loaded kernel: ffffffff81000000->ffffffff81d44000
> (XEN) Init. ramdisk: 0000000000000000->0000000000000000
> (XEN) Phys-Mach map: 0000008000000000->0000008000200000
> (XEN) Start info: ffffffff81d44000->ffffffff81d444b4
> (XEN) Page tables: ffffffff81d45000->ffffffff81d58000
> (XEN) Boot stack: ffffffff81d58000->ffffffff81d59000
> (XEN) TOTAL: ffffffff80000000->ffffffff82000000
> (XEN) ENTRY ADDRESS: ffffffff81aa71f0
> (XEN) Dom0 has maximum 8 VCPUs
> (XEN) Scrubbing Free RAM on 1 nodes using 8 CPUs
> (XEN) .............done.
> (XEN) Initial low memory virq threshold set at 0x4000 pages.
> (XEN) Std. Loglevel: All
> (XEN) Guest Loglevel: All
> (XEN) Xen is keeping VGA console.
> (XEN) *** Serial input -> Xen (type 'CTRL-a' three times to switch input to DOM0)
> (XEN) Freed 316kB init memory.
> mapping kernel into physical memory
> about to get started...
> (XEN) PCI add device 0000:00:00.0
> […]
> (XEN) PCI add device 0000:0c:05.0
> (XEN) Monitor-Mwait will be used to enter C1 state
> (XEN) Monitor-Mwait will be used to enter C2 state
> (XEN) Monitor-Mwait will be used to enter C3 state
>
>
> This is hostname (Linux x86_64 4.4.26-gentoo-Dom0-44-r2) 17:38:29, on hvc0
>
> hostname login:
>
>
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xen.org
https://lists.xen.org/xen-devel
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2017-01-04 20:08 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-12-28 14:17 blank screen VGA or Serial while linux boot Daniele Palumbo
2016-12-29 14:49 ` Konrad Rzeszutek Wilk
2016-12-29 17:44 ` Daniele Palumbo
2017-01-04 20:08 ` Konrad Rzeszutek Wilk
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.