From mboxrd@z Thu Jan 1 00:00:00 1970 From: =?UTF-8?B?UmFmYcWCIE1pxYJlY2tp?= Date: Sat, 7 May 2011 11:41:21 +0200 Subject: Interesting 14e4:4321 In-Reply-To: <274308290.20110507111432@googlemail.com> References: <4DC469E1.2040101@hauke-m.de> <479014597.20110507002540@googlemail.com> <274308290.20110507111432@googlemail.com> Message-ID: List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: b43-dev@lists.infradead.org Swen, really, include ML in your "to". It's second time. ---------- Wiadomo?? przekazana dalej ---------- Od: Swen Weiland Data: 7 maja 2011 11:14 Temat: Re: Fwd: Interesting 14e4:4321 Do: Rafa? Mi?ecki DW: Hauke Mehrtens Today I did some more detailed testing an I have to clarify what works and what not. The device does not work with DMA (currently), PIO mode is required. With PIO mode: "iwlist wlan0 scan" works and networks are reported. Signal strength in the report does not work. It is always: ?Quality=70/70 ?Signal level=0 dBm Associate with with AP seems to work but no data transfer b43-phy1: Broadcom 4321 WLAN found (core revision 12) b43-phy1 debug: Found PHY: Analog 5, Type 4, Revision 2 b43-phy1 debug: Found Radio: Manuf 0x17F, Version 0x2055, Revision 4 ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' Registered led device: b43-phy1::tx Registered led device: b43-phy1::rx Broadcom 43xx driver loaded [ Features: PNL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ] b43-phy1: Loading firmware version 410.2160 (2007-05-26 15:32:10) b43-phy1 debug: Chip initialized b43-phy1 debug: PIO initialized b43-phy1 debug: QoS enabled b43-phy1 debug: Wireless interface started b43-phy1 debug: Adding Interface type 2 wlan0: authenticate with 68:7f:74:06:b8:e8 (try 1) wlan0: authenticated wlan0: associate with 68:7f:74:06:b8:e8 (try 1) wlan0: RX AssocResp from 68:7f:74:06:b8:e8 (capab=0x401 status=0 aid=1) wlan0: associated ieee80211 phy1: wlan0: No probe response from AP 68:7f:74:06:b8:e8 after 500ms, disconnecting. Managed mode can be set and the AP is visible. Connecting to it is not possible and the device stops working with: b43-phy1: Loading firmware version 410.2160 (2007-05-26 15:32:10) b43-phy1 debug: Chip initialized b43-phy1 debug: PIO initialized b43-phy1 debug: QoS enabled b43-phy1 debug: Wireless interface started device wlan0 entered promiscuous mode b43-phy1 debug: Adding Interface type 3 br-lan: port 2(wlan0) entering forwarding state br-lan: port 2(wlan0) entering forwarding state b43-phy1 debug: Set beacon interval to 100 b43-phy1 debug: Updated beacon template at 0x68 b43-phy1 debug: Updated beacon template at 0x468 device wlan0 left promiscuous mode br-lan: port 2(wlan0) entering forwarding state device wlan0 entered promiscuous mode br-lan: port 2(wlan0) entering forwarding state br-lan: port 2(wlan0) entering forwarding state NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 NOHZ: local_softirq_pending 08 -- Mit freundlichen Gr??en Swen Weiland