[PATCH v2 2/3] arm64: dts: qcom: sdm845-xiaomi-beryllium-common: move common nodes to a common dtsi

[Joel Selvaraj <joel.selvaraj@outlook.com>]

Since there are two variants of Xiaomi Poco F1, move the common nodes from
Tianma variant into a new common dtsi. The EBBG variant will also inherit
the new common dtsi.

Signed-off-by: Joel Selvaraj <joel.selvaraj@outlook.com>
---
 .../qcom/sdm845-xiaomi-beryllium-common.dtsi  | 595 ++++++++++++++++++
 .../qcom/sdm845-xiaomi-beryllium-tianma.dts   | 590 +----------------
 2 files changed, 598 insertions(+), 587 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
new file mode 100644
index 000000000000..83edcb1171f5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/*
+ * Delete following upstream (sdm845.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &tz_mem;
+/delete-node/ &adsp_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &rmtfs_mem;
+
+/ {
+	model = "Xiaomi Pocophone F1";
+	compatible = "xiaomi,beryllium", "qcom,sdm845";
+	chassis-type = "handset";
+
+	/* required for bootloader to select correct board */
+	qcom,board-id = <69 0>;
+	qcom,msm-id = <321 0x20001>;
+
+	aliases {
+		hsuart0 = &uart6;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_pin_a>;
+
+		vol-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Reserved memory changes from downstream */
+	reserved-memory {
+		tz_mem: memory@86200000 {
+			reg = <0 0x86200000 0 0x4900000>;
+			no-map;
+		};
+
+		adsp_mem: memory@8c500000 {
+			reg = <0 0x8c500000 0 0x1e00000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@8e300000 {
+			reg = <0 0x8e300000 0 0x100000>;
+			no-map;
+		};
+
+		mpss_region: memory@8e400000 {
+			reg = <0 0x8e400000 0 0x7800000>;
+			no-map;
+		};
+
+		venus_mem: memory@95c00000 {
+			reg = <0 0x95c00000 0 0x500000>;
+			no-map;
+		};
+
+		cdsp_mem: memory@96100000 {
+			reg = <0 0x96100000 0 0x800000>;
+			no-map;
+		};
+
+		mba_region: memory@96900000 {
+			reg = <0 0x96900000 0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@96b00000 {
+			reg = <0 0x96b00000 0 0x1400000>;
+			no-map;
+		};
+
+		spss_mem: memory@97f00000 {
+			reg = <0 0x97f00000 0 0x100000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f6301000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xf6301000 0 0x200000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+	};
+
+	vreg_s4a_1p8: vreg-s4a-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&adsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&cdsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l26a_1p2>;
+
+	display_panel: panel@0 {
+		reg = <0>;
+		vddio-supply = <&vreg_l14a_1p8>;
+		vddpos-supply = <&lab>;
+		vddneg-supply = <&ibb>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight = <&pmi8998_wled>;
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		status = "disabled";
+
+		port {
+			panel_in_0: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in_0>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l1a_0p875>;
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
+};
+
+&gmu {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
+	};
+};
+
+&ibb {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-soft-start;
+	qcom,discharge-resistor-kohms = <300>;
+};
+
+&lab {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-soft-start;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
+};
+
+&ipa {
+	status = "okay";
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
+};
+
+&pm8998_gpio {
+	vol_up_pin_a: vol-up-active {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+};
+
+&pmi8998_wled {
+	status = "okay";
+	qcom,current-boost-limit = <970>;
+	qcom,ovp-millivolt = <29600>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+	qcom,switching-freq = <600>;
+	qcom,external-pfet;
+	qcom,cabc;
+};
+
+&pm8998_pon {
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
+&q6afedai {
+	qi2s@22 {
+		reg = <22>;
+		qcom,sd-lines = <0>;
+	};
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
+};
+
+&sound {
+	compatible = "qcom,db845c-sndcard";
+	pinctrl-0 = <&quat_mi2s_active
+			&quat_mi2s_sd0_active>;
+	pinctrl-names = "default";
+	model = "Xiaomi Poco F1";
+	audio-routing =
+		"RX_BIAS", "MCLK",
+		"AMIC1", "MIC BIAS1",
+		"AMIC2", "MIC BIAS2",
+		"AMIC3", "MIC BIAS3";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai =  <&wcd9340 0>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9340 1>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	sdc2_default_state: sdc2-default {
+		clk {
+			pins = "sdc2_clk";
+			bias-disable;
+			drive-strength = <16>;
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		data {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+	};
+
+	sdc2_card_det_n: sd-card-det-n {
+		pins = "gpio126";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	wcd_intr_default: wcd_intr_default {
+		pins = <54>;
+		function = "gpio";
+
+		input-enable;
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&venus {
+	status = "okay";
+	firmware-name = "qcom/sdm845/beryllium/venus.mbn";
+};
+
+&wcd9340{
+	pinctrl-0 = <&wcd_intr_default>;
+	pinctrl-names = "default";
+	clock-names = "extclk";
+	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+	reset-gpios = <&tlmm 64 0>;
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
+	qcom,micbias1-microvolt = <2700000>;
+	qcom,micbias2-microvolt = <1800000>;
+	qcom,micbias3-microvolt = <2700000>;
+	qcom,micbias4-microvolt = <2700000>;
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_uart6_default {
+	pinmux {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "qup6";
+	};
+
+	cts {
+		pins = "gpio45";
+		bias-disable;
+	};
+
+	rts-tx {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio48";
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
index d88dc07205f7..fcbef5ad2909 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-tianma.dts
@@ -2,593 +2,9 @@
 
 /dts-v1/;
 
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-#include <dt-bindings/sound/qcom,q6afe.h>
-#include <dt-bindings/sound/qcom,q6asm.h>
-#include "sdm845.dtsi"
-#include "pm8998.dtsi"
-#include "pmi8998.dtsi"
+#include "sdm845-xiaomi-beryllium-common.dtsi"
 
-/*
- * Delete following upstream (sdm845.dtsi) reserved
- * memory mappings which are different in this device.
- */
-/delete-node/ &tz_mem;
-/delete-node/ &adsp_mem;
-/delete-node/ &wlan_msa_mem;
-/delete-node/ &mpss_region;
-/delete-node/ &venus_mem;
-/delete-node/ &cdsp_mem;
-/delete-node/ &mba_region;
-/delete-node/ &slpi_mem;
-/delete-node/ &spss_mem;
-/delete-node/ &rmtfs_mem;
-
-/ {
-	model = "Xiaomi Pocophone F1";
-	compatible = "xiaomi,beryllium", "qcom,sdm845";
-	chassis-type = "handset";
-
-	/* required for bootloader to select correct board */
-	qcom,board-id = <69 0>;
-	qcom,msm-id = <321 0x20001>;
-
-	aliases {
-		hsuart0 = &uart6;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		autorepeat;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&vol_up_pin_a>;
-
-		vol-up {
-			label = "Volume Up";
-			linux,code = <KEY_VOLUMEUP>;
-			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	/* Reserved memory changes from downstream */
-	reserved-memory {
-		tz_mem: memory@86200000 {
-			reg = <0 0x86200000 0 0x4900000>;
-			no-map;
-		};
-
-		adsp_mem: memory@8c500000 {
-			reg = <0 0x8c500000 0 0x1e00000>;
-			no-map;
-		};
-
-		wlan_msa_mem: memory@8e300000 {
-			reg = <0 0x8e300000 0 0x100000>;
-			no-map;
-		};
-
-		mpss_region: memory@8e400000 {
-			reg = <0 0x8e400000 0 0x7800000>;
-			no-map;
-		};
-
-		venus_mem: memory@95c00000 {
-			reg = <0 0x95c00000 0 0x500000>;
-			no-map;
-		};
-
-		cdsp_mem: memory@96100000 {
-			reg = <0 0x96100000 0 0x800000>;
-			no-map;
-		};
-
-		mba_region: memory@96900000 {
-			reg = <0 0x96900000 0 0x200000>;
-			no-map;
-		};
-
-		slpi_mem: memory@96b00000 {
-			reg = <0 0x96b00000 0 0x1400000>;
-			no-map;
-		};
-
-		spss_mem: memory@97f00000 {
-			reg = <0 0x97f00000 0 0x100000>;
-			no-map;
-		};
-
-		rmtfs_mem: memory@f6301000 {
-			compatible = "qcom,rmtfs-mem";
-			reg = <0 0xf6301000 0 0x200000>;
-			no-map;
-
-			qcom,client-id = <1>;
-			qcom,vmid = <15>;
-		};
-	};
-
-	vreg_s4a_1p8: vreg-s4a-1p8 {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_s4a_1p8";
-
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-};
-
-&adsp_pas {
-	status = "okay";
-	firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
-};
-
-&apps_rsc {
-	pm8998-rpmh-regulators {
-		compatible = "qcom,pm8998-rpmh-regulators";
-		qcom,pmic-id = "a";
-
-		vreg_l1a_0p875: ldo1 {
-			regulator-min-microvolt = <880000>;
-			regulator-max-microvolt = <880000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l5a_0p8: ldo5 {
-			regulator-min-microvolt = <800000>;
-			regulator-max-microvolt = <800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7a_1p8: ldo7 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l12a_1p8: ldo12 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l13a_2p95: ldo13 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2960000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l14a_1p8: ldo14 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-boot-on;
-			regulator-always-on;
-		};
-
-		vreg_l17a_1p3: ldo17 {
-			regulator-min-microvolt = <1304000>;
-			regulator-max-microvolt = <1304000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l20a_2p95: ldo20 {
-			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <2968000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l21a_2p95: ldo21 {
-			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <2968000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l23a_3p3: ldo23 {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3312000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l24a_3p075: ldo24 {
-			regulator-min-microvolt = <3088000>;
-			regulator-max-microvolt = <3088000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l25a_3p3: ldo25 {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3312000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l26a_1p2: ldo26 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-boot-on;
-		};
-	};
-};
-
-&cdsp_pas {
+&display_panel {
+	compatible = "tianma,fhd-video";
 	status = "okay";
-	firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
-};
-
-&dsi0 {
-	status = "okay";
-	vdda-supply = <&vreg_l26a_1p2>;
-
-	panel@0 {
-		compatible = "tianma,fhd-video";
-		reg = <0>;
-		vddio-supply = <&vreg_l14a_1p8>;
-		vddpos-supply = <&lab>;
-		vddneg-supply = <&ibb>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		backlight = <&pmi8998_wled>;
-		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
-
-		port {
-			tianma_nt36672a_in_0: endpoint {
-				remote-endpoint = <&dsi0_out>;
-			};
-		};
-	};
-};
-
-&dsi0_out {
-	remote-endpoint = <&tianma_nt36672a_in_0>;
-	data-lanes = <0 1 2 3>;
-};
-
-&dsi0_phy {
-	status = "okay";
-	vdds-supply = <&vreg_l1a_0p875>;
-};
-
-&gcc {
-	protected-clocks = <GCC_QSPI_CORE_CLK>,
-			   <GCC_QSPI_CORE_CLK_SRC>,
-			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
-			   <GCC_LPASS_Q6_AXI_CLK>,
-			   <GCC_LPASS_SWAY_CLK>;
-};
-
-&gmu {
-	status = "okay";
-};
-
-&gpu {
-	status = "okay";
-
-	zap-shader {
-		memory-region = <&gpu_mem>;
-		firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
-	};
-};
-
-&ibb {
-	regulator-min-microvolt = <4600000>;
-	regulator-max-microvolt = <6000000>;
-	regulator-over-current-protection;
-	regulator-pull-down;
-	regulator-soft-start;
-	qcom,discharge-resistor-kohms = <300>;
-};
-
-&lab {
-	regulator-min-microvolt = <4600000>;
-	regulator-max-microvolt = <6000000>;
-	regulator-over-current-protection;
-	regulator-pull-down;
-	regulator-soft-start;
-};
-
-&mdss {
-	status = "okay";
-};
-
-&mss_pil {
-	status = "okay";
-	firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
-};
-
-&ipa {
-	status = "okay";
-	memory-region = <&ipa_fw_mem>;
-	firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
-};
-
-&pm8998_gpio {
-	vol_up_pin_a: vol-up-active {
-		pins = "gpio6";
-		function = "normal";
-		input-enable;
-		bias-pull-up;
-		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-	};
-};
-
-&pmi8998_wled {
-	status = "okay";
-	qcom,current-boost-limit = <970>;
-	qcom,ovp-millivolt = <29600>;
-	qcom,current-limit-microamp = <20000>;
-	qcom,num-strings = <2>;
-	qcom,switching-freq = <600>;
-	qcom,external-pfet;
-	qcom,cabc;
-};
-
-&pm8998_pon {
-	resin {
-		compatible = "qcom,pm8941-resin";
-		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
-		debounce = <15625>;
-		bias-pull-up;
-		linux,code = <KEY_VOLUMEDOWN>;
-	};
-};
-
-/* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
-&q6afedai {
-	qi2s@22 {
-		reg = <22>;
-		qcom,sd-lines = <0>;
-	};
-};
-
-&q6asmdai {
-	dai@0 {
-		reg = <0>;
-	};
-
-	dai@1 {
-		reg = <1>;
-	};
-
-	dai@2 {
-		reg = <2>;
-	};
-};
-
-&qupv3_id_0 {
-	status = "okay";
-};
-
-&sdhc_2 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
-
-	vmmc-supply = <&vreg_l21a_2p95>;
-	vqmmc-supply = <&vreg_l13a_2p95>;
-
-	bus-width = <4>;
-	cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
-};
-
-&sound {
-	compatible = "qcom,db845c-sndcard";
-	pinctrl-0 = <&quat_mi2s_active
-			&quat_mi2s_sd0_active>;
-	pinctrl-names = "default";
-	model = "Xiaomi Poco F1";
-	audio-routing =
-		"RX_BIAS", "MCLK",
-		"AMIC1", "MIC BIAS1",
-		"AMIC2", "MIC BIAS2",
-		"AMIC3", "MIC BIAS3";
-
-	mm1-dai-link {
-		link-name = "MultiMedia1";
-		cpu {
-			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
-		};
-	};
-
-	mm2-dai-link {
-		link-name = "MultiMedia2";
-		cpu {
-			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
-		};
-	};
-
-	mm3-dai-link {
-		link-name = "MultiMedia3";
-		cpu {
-			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
-		};
-	};
-
-	slim-dai-link {
-		link-name = "SLIM Playback";
-		cpu {
-			sound-dai = <&q6afedai SLIMBUS_0_RX>;
-		};
-
-		platform {
-			sound-dai = <&q6routing>;
-		};
-
-		codec {
-			sound-dai =  <&wcd9340 0>;
-		};
-	};
-
-	slimcap-dai-link {
-		link-name = "SLIM Capture";
-		cpu {
-			sound-dai = <&q6afedai SLIMBUS_0_TX>;
-		};
-
-		platform {
-			sound-dai = <&q6routing>;
-		};
-
-		codec {
-			sound-dai = <&wcd9340 1>;
-		};
-	};
-};
-
-&tlmm {
-	gpio-reserved-ranges = <0 4>, <81 4>;
-
-	sdc2_default_state: sdc2-default {
-		clk {
-			pins = "sdc2_clk";
-			bias-disable;
-			drive-strength = <16>;
-		};
-
-		cmd {
-			pins = "sdc2_cmd";
-			bias-pull-up;
-			drive-strength = <10>;
-		};
-
-		data {
-			pins = "sdc2_data";
-			bias-pull-up;
-			drive-strength = <10>;
-		};
-	};
-
-	sdc2_card_det_n: sd-card-det-n {
-		pins = "gpio126";
-		function = "gpio";
-		bias-pull-up;
-	};
-
-	wcd_intr_default: wcd_intr_default {
-		pins = <54>;
-		function = "gpio";
-
-		input-enable;
-		bias-pull-down;
-		drive-strength = <2>;
-	};
-};
-
-&uart6 {
-	status = "okay";
-
-	bluetooth {
-		compatible = "qcom,wcn3990-bt";
-
-		vddio-supply = <&vreg_s4a_1p8>;
-		vddxo-supply = <&vreg_l7a_1p8>;
-		vddrf-supply = <&vreg_l17a_1p3>;
-		vddch0-supply = <&vreg_l25a_3p3>;
-		max-speed = <3200000>;
-	};
-};
-
-&ufs_mem_hc {
-	status = "okay";
-
-	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
-
-	vcc-supply = <&vreg_l20a_2p95>;
-	vcc-max-microamp = <800000>;
-};
-
-&ufs_mem_phy {
-	status = "okay";
-
-	vdda-phy-supply = <&vreg_l1a_0p875>;
-	vdda-pll-supply = <&vreg_l26a_1p2>;
-};
-
-&usb_1 {
-	status = "okay";
-};
-
-&usb_1_dwc3 {
-	dr_mode = "peripheral";
-};
-
-&usb_1_hsphy {
-	status = "okay";
-
-	vdd-supply = <&vreg_l1a_0p875>;
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-
-	qcom,imp-res-offset-value = <8>;
-	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
-	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
-	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
-};
-
-&usb_1_qmpphy {
-	status = "okay";
-
-	vdda-phy-supply = <&vreg_l26a_1p2>;
-	vdda-pll-supply = <&vreg_l1a_0p875>;
-};
-
-&venus {
-	status = "okay";
-	firmware-name = "qcom/sdm845/beryllium/venus.mbn";
-};
-
-&wcd9340{
-	pinctrl-0 = <&wcd_intr_default>;
-	pinctrl-names = "default";
-	clock-names = "extclk";
-	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
-	reset-gpios = <&tlmm 64 0>;
-	vdd-buck-supply = <&vreg_s4a_1p8>;
-	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
-	vdd-tx-supply = <&vreg_s4a_1p8>;
-	vdd-rx-supply = <&vreg_s4a_1p8>;
-	vdd-io-supply = <&vreg_s4a_1p8>;
-	qcom,micbias1-microvolt = <2700000>;
-	qcom,micbias2-microvolt = <1800000>;
-	qcom,micbias3-microvolt = <2700000>;
-	qcom,micbias4-microvolt = <2700000>;
-};
-
-&wifi {
-	status = "okay";
-
-	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
-	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
-	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
-	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
-	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
-};
-
-/* PINCTRL - additions to nodes defined in sdm845.dtsi */
-
-&qup_uart6_default {
-	pinmux {
-		pins = "gpio45", "gpio46", "gpio47", "gpio48";
-		function = "qup6";
-	};
-
-	cts {
-		pins = "gpio45";
-		bias-disable;
-	};
-
-	rts-tx {
-		pins = "gpio46", "gpio47";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	rx {
-		pins = "gpio48";
-		bias-pull-up;
-	};
 };
-- 
2.37.1