Wiphy phy0
	Band 1:
		Capabilities: 0x820
			HT20
			Static SM Power Save
			RX HT20 SGI
			No RX STBC
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-23
		TX unequal modulation not supported
		HT TX Max spatial streams: 2
		HT TX MCS rate indexes supported may differ
		Frequencies:
			* 2412 MHz [1] (14.0 dBm)
			* 2417 MHz [2] (14.0 dBm)
			* 2422 MHz [3] (14.0 dBm)
			* 2427 MHz [4] (14.0 dBm)
			* 2432 MHz [5] (14.0 dBm)
			* 2437 MHz [6] (14.0 dBm)
			* 2442 MHz [7] (14.0 dBm)
			* 2447 MHz [8] (14.0 dBm)
			* 2452 MHz [9] (14.0 dBm)
			* 2457 MHz [10] (14.0 dBm)
			* 2462 MHz [11] (14.0 dBm)
		Bitrates (non-HT):
			* 1.0 Mbps
			* 2.0 Mbps (short preamble supported)
			* 5.5 Mbps (short preamble supported)
			* 11.0 Mbps (short preamble supported)
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
	Band 2:
		Capabilities: 0x862
			HT20/HT40
			Static SM Power Save
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-23, 32
		TX unequal modulation not supported
		HT TX Max spatial streams: 2
		HT TX MCS rate indexes supported may differ
		Frequencies:
			* 5180 MHz [36] (15.0 dBm) (passive scanning, no IBSS)
			* 5200 MHz [40] (15.0 dBm) (passive scanning, no IBSS)
			* 5220 MHz [44] (15.0 dBm) (passive scanning, no IBSS)
			* 5240 MHz [48] (15.0 dBm) (passive scanning, no IBSS)
			* 5260 MHz [52] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5280 MHz [56] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5300 MHz [60] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5320 MHz [64] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5745 MHz [149] (16.0 dBm) (passive scanning, no IBSS)
			* 5765 MHz [153] (16.0 dBm) (passive scanning, no IBSS)
			* 5785 MHz [157] (16.0 dBm) (passive scanning, no IBSS)
			* 5805 MHz [161] (16.0 dBm) (passive scanning, no IBSS)
			* 5825 MHz [165] (16.0 dBm) (passive scanning, no IBSS)
		Bitrates (non-HT):
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
	max # scan SSIDs: 20
	max scan IEs length: 127 bytes
	Coverage class: 0 (up to 0m)
	Supported Ciphers:
		* WEP40 (00-0f-ac:1)
		* WEP104 (00-0f-ac:5)
		* TKIP (00-0f-ac:2)
		* CCMP (00-0f-ac:4)
	Available Antennas: TX 0 RX 0
	Supported interface modes:
		 * IBSS
		 * managed
		 * monitor
	software interface modes (can always be added):
		 * monitor
	interface combinations are not supported
	Supported commands:
		 * new_interface
		 * set_interface
		 * new_key
		 * new_beacon
		 * new_station
		 * new_mpath
		 * set_mesh_params
		 * set_bss
		 * authenticate
		 * associate
		 * deauthenticate
		 * disassociate
		 * join_ibss
		 * join_mesh
		 * remain_on_channel
		 * set_tx_bitrate_mask
		 * action
		 * frame_wait_cancel
		 * set_wiphy_netns
		 * set_channel
		 * set_wds_peer
		 * connect
		 * disconnect
	Supported TX frame types:
		 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
	Supported RX frame types:
		 * IBSS: 0xd0
		 * managed: 0x40 0xd0
		 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * mesh point: 0xb0 0xc0 0xd0
		 * P2P-client: 0x40 0xd0
		 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0