* [PATCH 0/8] ARM: at91: atmel_lcdc: add DT support
@ 2013-04-11 14:57 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 14:57 UTC (permalink / raw)
To: inux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andrew Morton
HI,
The following patch series add the DT support of the Atmel LCDC
controler and update the 9263 and 9g45 Atmel Reference board
At the same time some cleanup is done on the drivers implementation as
we was using the internal data struct as platform data
The following changes since commit d920129d817acc5f7ebfadeb7ecbce70ab161f6c:
ARM: at91/avr32/atmel_lcdfb: add platform device-id table (2013-04-11 21:00:56 +0800)
are available in the git repository at:
git://github.com/at91linux/linux-at91.git j/for-3.10_atmel_lcd_dt
for you to fetch changes up to 6354e161060c2d90f0935d14d037e2f126b8c6e5:
ARM: at91: sam9263ek: add dt lcd support (2013-04-11 21:18:21 +0800)
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (8):
video: atmel_lcdfb: fix platform data struct
video: atmel_lcdfb: introduce atmel_lcdfb_power_control
video: atmel_lcdfb: pass the pdata as params
video: atmel_lcdfb: add device tree suport
ARM: at91: sam9g45: add lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263ek: add dt lcd support
Documentation/devicetree/bindings/video/atmel,lcdc.txt | 75 +++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++
arch/arm/boot/dts/at91sam9263ek.dts | 30 +++++++++++++++
arch/arm/boot/dts/at91sam9g45.dtsi | 47 +++++++++++++++++++++++
arch/arm/boot/dts/at91sam9m10g45ek.dts | 29 +++++++++++++++
arch/arm/mach-at91/at91sam9261_devices.c | 6 +--
arch/arm/mach-at91/at91sam9263_devices.c | 6 +--
arch/arm/mach-at91/at91sam9g45_devices.c | 6 +--
arch/arm/mach-at91/at91sam9rl_devices.c | 6 +--
arch/arm/mach-at91/board-sam9261ek.c | 10 ++---
arch/arm/mach-at91/board-sam9263ek.c | 6 +--
arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
arch/arm/mach-at91/board-sam9rlek.c | 6 +--
arch/arm/mach-at91/board.h | 4 +-
arch/avr32/boards/atngw100/evklcd10x.c | 8 ++--
arch/avr32/boards/atngw100/mrmt.c | 4 +-
arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
arch/avr32/boards/atstk1000/setup.c | 2 +-
arch/avr32/boards/favr-32/setup.c | 2 +-
arch/avr32/boards/hammerhead/setup.c | 2 +-
arch/avr32/boards/merisc/display.c | 2 +-
arch/avr32/boards/mimc200/setup.c | 4 +-
arch/avr32/mach-at32ap/at32ap700x.c | 8 ++--
arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
drivers/video/Kconfig | 2 +
drivers/video/atmel_lcdfb.c | 342 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++---------------------------------
include/video/atmel_lcdc.h | 26 ++-----------
27 files changed, 547 insertions(+), 135 deletions(-)
create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
Best Regards,
J.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 0/8] ARM: at91: atmel_lcdc: add DT support
@ 2013-04-11 14:57 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 14:57 UTC (permalink / raw)
To: inux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andrew Morton
HI,
The following patch series add the DT support of the Atmel LCDC
controler and update the 9263 and 9g45 Atmel Reference board
At the same time some cleanup is done on the drivers implementation as
we was using the internal data struct as platform data
The following changes since commit d920129d817acc5f7ebfadeb7ecbce70ab161f6c:
ARM: at91/avr32/atmel_lcdfb: add platform device-id table (2013-04-11 21:00:56 +0800)
are available in the git repository at:
git://github.com/at91linux/linux-at91.git j/for-3.10_atmel_lcd_dt
for you to fetch changes up to 6354e161060c2d90f0935d14d037e2f126b8c6e5:
ARM: at91: sam9263ek: add dt lcd support (2013-04-11 21:18:21 +0800)
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (8):
video: atmel_lcdfb: fix platform data struct
video: atmel_lcdfb: introduce atmel_lcdfb_power_control
video: atmel_lcdfb: pass the pdata as params
video: atmel_lcdfb: add device tree suport
ARM: at91: sam9g45: add lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263ek: add dt lcd support
Documentation/devicetree/bindings/video/atmel,lcdc.txt | 75 +++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++
arch/arm/boot/dts/at91sam9263ek.dts | 30 +++++++++++++++
arch/arm/boot/dts/at91sam9g45.dtsi | 47 +++++++++++++++++++++++
arch/arm/boot/dts/at91sam9m10g45ek.dts | 29 +++++++++++++++
arch/arm/mach-at91/at91sam9261_devices.c | 6 +--
arch/arm/mach-at91/at91sam9263_devices.c | 6 +--
arch/arm/mach-at91/at91sam9g45_devices.c | 6 +--
arch/arm/mach-at91/at91sam9rl_devices.c | 6 +--
arch/arm/mach-at91/board-sam9261ek.c | 10 ++---
arch/arm/mach-at91/board-sam9263ek.c | 6 +--
arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
arch/arm/mach-at91/board-sam9rlek.c | 6 +--
arch/arm/mach-at91/board.h | 4 +-
arch/avr32/boards/atngw100/evklcd10x.c | 8 ++--
arch/avr32/boards/atngw100/mrmt.c | 4 +-
arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
arch/avr32/boards/atstk1000/setup.c | 2 +-
arch/avr32/boards/favr-32/setup.c | 2 +-
arch/avr32/boards/hammerhead/setup.c | 2 +-
arch/avr32/boards/merisc/display.c | 2 +-
arch/avr32/boards/mimc200/setup.c | 4 +-
arch/avr32/mach-at32ap/at32ap700x.c | 8 ++--
arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
drivers/video/Kconfig | 2 +
drivers/video/atmel_lcdfb.c | 342 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++---------------------------------
include/video/atmel_lcdc.h | 26 ++-----------
27 files changed, 547 insertions(+), 135 deletions(-)
create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
Best Regards,
J.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-04-11 14:57 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: linux-fbdev, devicetree-discuss, Nicolas Ferre, Andrew Morton,
Jean-Christophe PLAGNIOL-VILLARD, Hans-Christian Egtvedt
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
---
arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
arch/arm/mach-at91/board-sam9261ek.c | 6 +-
arch/arm/mach-at91/board-sam9263ek.c | 4 +-
arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
arch/arm/mach-at91/board-sam9rlek.c | 4 +-
arch/arm/mach-at91/board.h | 4 +-
arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
arch/avr32/boards/atngw100/mrmt.c | 4 +-
arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
arch/avr32/boards/atstk1000/setup.c | 2 +-
arch/avr32/boards/favr-32/setup.c | 2 +-
arch/avr32/boards/hammerhead/setup.c | 2 +-
arch/avr32/boards/merisc/display.c | 2 +-
arch/avr32/boards/mimc200/setup.c | 4 +-
arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
include/video/atmel_lcdc.h | 24 +------
21 files changed, 109 insertions(+), 101 deletions(-)
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 629ea5f..b2a3474 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -465,7 +465,7 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -498,7 +498,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data) {
return;
@@ -559,7 +559,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 858c8aa..4aeaddd 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -832,7 +832,7 @@ void __init at91_add_device_can(struct at91_can_data *data) {}
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -859,7 +859,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data)
return;
@@ -891,7 +891,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index fe626d4..82636c7 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -965,7 +965,7 @@ void __init at91_add_device_isi(struct isi_platform_data *data,
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -991,7 +991,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data)
return;
@@ -1037,7 +1037,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index 352468f..a698bda 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -498,7 +498,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -525,7 +525,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data) {
return;
@@ -557,7 +557,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index b446645..c819e29 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -405,7 +405,7 @@ static void at91_lcdc_stn_power_control(int on)
}
}
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.default_bpp = 1,
.default_dmacon = ATMEL_LCDC_DMAEN,
.default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
@@ -460,7 +460,7 @@ static void at91_lcdc_tft_power_control(int on)
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
}
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -475,7 +475,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
#endif
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 3284df0..0fdae3f 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -281,7 +281,7 @@ static void at91_lcdc_power_control(int on)
}
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -292,7 +292,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index 2a94896..ef39078 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -284,7 +284,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 32,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -295,7 +295,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index aa265dc..b77d7a9 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -179,7 +179,7 @@ static void at91_lcdc_power_control(int on)
}
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -191,7 +191,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h
index 4a234fb..6c08b34 100644
--- a/arch/arm/mach-at91/board.h
+++ b/arch/arm/mach-at91/board.h
@@ -107,8 +107,8 @@ extern void __init at91_add_device_pwm(u32 mask);
extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
/* LCD Controller */
-struct atmel_lcdfb_info;
-extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
+struct atmel_lcdfb_pdata;
+extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
/* AC97 */
extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index 2038875..dc42804 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -58,7 +58,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 28330000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -96,7 +96,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 7000000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -134,7 +134,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 6400000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c
index f914319..ccc9599 100644
--- a/arch/avr32/boards/atngw100/mrmt.c
+++ b/arch/avr32/boards/atngw100/mrmt.c
@@ -83,7 +83,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
.dclkmax = 9260000,
};
-static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -126,7 +126,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
.dclkmax = 9260000,
};
-static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
index 9392d32..653cc09 100644
--- a/arch/avr32/boards/atstk1000/atstk1000.h
+++ b/arch/avr32/boards/atstk1000/atstk1000.h
@@ -10,7 +10,7 @@
#ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
#define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
-extern struct atmel_lcdfb_info atstk1000_lcdc_data;
+extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
void atstk1000_setup_j2_leds(void);
diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
index 2d6b560..b6b88f5 100644
--- a/arch/avr32/boards/atstk1000/setup.c
+++ b/arch/avr32/boards/atstk1000/setup.c
@@ -55,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = {
.dclkmax = 30000000,
};
-struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
index 27bd6fb..7b1f2cd 100644
--- a/arch/avr32/boards/favr-32/setup.c
+++ b/arch/avr32/boards/favr-32/setup.c
@@ -125,7 +125,7 @@ static struct fb_monspecs __initdata favr32_default_monspecs = {
.dclkmax = 28000000,
};
-struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata favr32_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
index 9d1efd1..dc0e317 100644
--- a/arch/avr32/boards/hammerhead/setup.c
+++ b/arch/avr32/boards/hammerhead/setup.c
@@ -77,7 +77,7 @@ static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
.dclkmax = 10000000,
};
-struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata hammerhead_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
index 85a543c..e7683ee 100644
--- a/arch/avr32/boards/merisc/display.c
+++ b/arch/avr32/boards/merisc/display.c
@@ -45,7 +45,7 @@ static struct fb_monspecs merisc_fb_monspecs = {
.dclkmax = 30000000,
};
-struct atmel_lcdfb_info merisc_lcdc_data = {
+struct atmel_lcdfb_pdata merisc_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
index 05358aa..1cb8e9c 100644
--- a/arch/avr32/boards/mimc200/setup.c
+++ b/arch/avr32/boards/mimc200/setup.c
@@ -8,7 +8,7 @@
* published by the Free Software Foundation.
*/
-extern struct atmel_lcdfb_info mimc200_lcdc_data;
+extern struct atmel_lcdfb_pdata mimc200_lcdc_data;
#include <linux/clk.h>
#include <linux/etherdevice.h>
@@ -71,7 +71,7 @@ static struct fb_monspecs __initdata mimc200_default_monspecs = {
.dclkmax = 25200000,
};
-struct atmel_lcdfb_info __initdata mimc200_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata mimc200_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 7c2f668..0badb05 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1437,7 +1437,7 @@ fail:
* LCDC
* -------------------------------------------------------------------- */
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
-static struct atmel_lcdfb_info atmel_lcdfb0_data;
+static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
static struct resource atmel_lcdfb0_resource[] = {
{
.start = 0xff000000,
@@ -1465,12 +1465,12 @@ static struct clk atmel_lcdfb0_pixclk = {
};
struct platform_device *__init
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
unsigned long fbmem_start, unsigned long fbmem_len,
u64 pin_mask)
{
struct platform_device *pdev;
- struct atmel_lcdfb_info *info;
+ struct atmel_lcdfb_pdata *info;
struct fb_monspecs *monspecs;
struct fb_videomode *modedb;
unsigned int modedb_size;
@@ -1527,7 +1527,7 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
}
info = pdev->dev.platform_data;
- memcpy(info, data, sizeof(struct atmel_lcdfb_info));
+ memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
info->default_monspecs = monspecs;
pdev->name = "at32ap-lcdfb";
diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h
index d485b03..f1a316d 100644
--- a/arch/avr32/mach-at32ap/include/mach/board.h
+++ b/arch/avr32/mach-at32ap/include/mach/board.h
@@ -44,9 +44,9 @@ struct platform_device *
at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
void at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n);
-struct atmel_lcdfb_info;
+struct atmel_lcdfb_pdata;
struct platform_device *
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
unsigned long fbmem_start, unsigned long fbmem_len,
u64 pin_mask);
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index c1a2914..98733cd4 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -20,12 +20,45 @@
#include <linux/gfp.h>
#include <linux/module.h>
#include <linux/platform_data/atmel.h>
+#include <video/of_display_timing.h>
#include <mach/cpu.h>
#include <asm/gpio.h>
#include <video/atmel_lcdc.h>
+struct atmel_lcdfb_config {
+ bool have_alt_pixclock;
+ bool have_hozval;
+ bool have_intensity_bit;
+};
+
+ /* LCD Controller info data structure, stored in device platform_data */
+struct atmel_lcdfb_info {
+ spinlock_t lock;
+ struct fb_info *info;
+ void __iomem *mmio;
+ int irq_base;
+ struct work_struct task;
+
+ unsigned int smem_len;
+ struct platform_device *pdev;
+ struct clk *bus_clk;
+ struct clk *lcdc_clk;
+
+ struct backlight_device *backlight;
+ u8 bl_power;
+ bool lcdcon_pol_negative;
+ u8 saved_lcdcon;
+
+ u32 pseudo_palette[16];
+ bool have_intensity_bit;
+
+ struct atmel_lcdfb_pdata pdata;
+
+ struct atmel_lcdfb_config *config;
+};
+
#define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
#define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
@@ -34,12 +67,6 @@
#define ATMEL_LCDC_DMA_BURST_LEN 8 /* words */
#define ATMEL_LCDC_FIFO_SIZE 512 /* words */
-struct atmel_lcdfb_config {
- bool have_alt_pixclock;
- bool have_hozval;
- bool have_intensity_bit;
-};
-
static struct atmel_lcdfb_config at91sam9261_config = {
.have_hozval = true,
.have_intensity_bit = true,
@@ -242,6 +269,8 @@ static void exit_backlight(struct atmel_lcdfb_info *sinfo)
static void init_contrast(struct atmel_lcdfb_info *sinfo)
{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
/* contrast pwm can be 'inverted' */
if (sinfo->lcdcon_pol_negative)
contrast_ctr &= ~(ATMEL_LCDC_POL_POSITIVE);
@@ -250,7 +279,7 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
- if (sinfo->lcdcon_is_backlight)
+ if (pdata->lcdcon_is_backlight)
init_backlight(sinfo);
}
@@ -293,9 +322,11 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
static void atmel_lcdfb_stop_nowait(struct atmel_lcdfb_info *sinfo)
{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
/* Turn off the LCD controller and the DMA controller */
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
- sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
+ pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
/* Wait for the LCDC core to become idle */
while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
@@ -315,9 +346,11 @@ static void atmel_lcdfb_stop(struct atmel_lcdfb_info *sinfo)
static void atmel_lcdfb_start(struct atmel_lcdfb_info *sinfo)
{
- lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
+ lcdc_writel(sinfo, ATMEL_LCDC_DMACON, pdata->default_dmacon);
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
- (sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
+ (pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
| ATMEL_LCDC_PWR);
}
@@ -418,6 +451,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
{
struct device *dev = info->device;
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned long clk_value_khz;
clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
@@ -501,7 +535,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
else
var->green.length = 6;
- if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
/* RGB:5X5 mode */
var->red.offset = var->green.length + 5;
var->blue.offset = 0;
@@ -518,7 +552,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
var->transp.length = 8;
/* fall through */
case 24:
- if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
/* RGB:888 mode */
var->red.offset = 16;
var->blue.offset = 0;
@@ -567,6 +601,7 @@ static void atmel_lcdfb_reset(struct atmel_lcdfb_info *sinfo)
static int atmel_lcdfb_set_par(struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned long hozval_linesz;
unsigned long value;
unsigned long clk_value_khz;
@@ -628,7 +663,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
/* Initialize control register 2 */
- value = sinfo->default_lcdcon2;
+ value = pdata->default_lcdcon2;
if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
value |= ATMEL_LCDC_INVLINE_INVERTED;
@@ -732,6 +767,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
unsigned int transp, struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned int val;
u32 *pal;
int ret = 1;
@@ -768,8 +804,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
*/
} else {
/* new style BGR:565 / RGB:565 */
- if (sinfo->lcd_wiring_mode ==
- ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
val = ((blue >> 11) & 0x001f);
val |= ((red >> 0) & 0xf800);
} else {
@@ -909,7 +944,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct fb_info *info;
struct atmel_lcdfb_info *sinfo;
- struct atmel_lcdfb_info *pdata_sinfo;
+ struct atmel_lcdfb_pdata *pdata;
struct fb_videomode fbmode;
struct resource *regs = NULL;
struct resource *map = NULL;
@@ -927,17 +962,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
sinfo = info->par;
if (dev->platform_data) {
- pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
- sinfo->default_bpp = pdata_sinfo->default_bpp;
- sinfo->default_dmacon = pdata_sinfo->default_dmacon;
- sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
- sinfo->default_monspecs = pdata_sinfo->default_monspecs;
- sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
- sinfo->guard_time = pdata_sinfo->guard_time;
- sinfo->smem_len = pdata_sinfo->smem_len;
- sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
- sinfo->lcdcon_pol_negative = pdata_sinfo->lcdcon_pol_negative;
- sinfo->lcd_wiring_mode = pdata_sinfo->lcd_wiring_mode;
+ pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
+ sinfo->pdata = *pdata;
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
@@ -953,7 +979,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
info->pseudo_palette = sinfo->pseudo_palette;
info->fbops = &atmel_lcdfb_ops;
- memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
+ memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
info->fix = atmel_lcdfb_fix;
/* Enable LCDC Clocks */
@@ -971,7 +997,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
info->monspecs.modedb_len, info->monspecs.modedb,
- sinfo->default_bpp);
+ pdata->default_bpp);
if (!ret) {
dev_err(dev, "no suitable video mode found\n");
goto stop_clk;
@@ -1088,8 +1114,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
fb_add_videomode(&fbmode, &info->modelist);
/* Power up the LCDC screen */
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(1);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(1);
dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
@@ -1134,15 +1160,17 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct fb_info *info = dev_get_drvdata(dev);
struct atmel_lcdfb_info *sinfo;
+ struct atmel_lcdfb_pdata *pdata;
if (!info || !info->par)
return 0;
sinfo = info->par;
+ pdata = &sinfo->pdata;
cancel_work_sync(&sinfo->task);
exit_backlight(sinfo);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(0);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(0);
unregister_framebuffer(info);
atmel_lcdfb_stop_clock(sinfo);
clk_put(sinfo->lcdc_clk);
@@ -1170,6 +1198,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
/*
* We don't want to handle interrupts while the clock is
@@ -1179,8 +1208,8 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(0);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(0);
atmel_lcdfb_stop(sinfo);
atmel_lcdfb_stop_clock(sinfo);
@@ -1192,11 +1221,12 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
atmel_lcdfb_start_clock(sinfo);
atmel_lcdfb_start(sinfo);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(1);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(1);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
/* Enable FIFO & DMA errors */
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 0f5a2fc..2eb601c 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -31,39 +31,17 @@
#define ATMEL_LCDC_WIRING_BGR 0
#define ATMEL_LCDC_WIRING_RGB 1
-struct atmel_lcdfb_config;
/* LCD Controller info data structure, stored in device platform_data */
-struct atmel_lcdfb_info {
- spinlock_t lock;
- struct fb_info *info;
- void __iomem *mmio;
- int irq_base;
- struct work_struct task;
-
+struct atmel_lcdfb_pdata {
unsigned int guard_time;
- unsigned int smem_len;
- struct platform_device *pdev;
- struct clk *bus_clk;
- struct clk *lcdc_clk;
-
-#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
- struct backlight_device *backlight;
- u8 bl_power;
-#endif
bool lcdcon_is_backlight;
- bool lcdcon_pol_negative;
- u8 saved_lcdcon;
-
u8 default_bpp;
u8 lcd_wiring_mode;
unsigned int default_lcdcon2;
unsigned int default_dmacon;
void (*atmel_lcdfb_power_control)(int on);
struct fb_monspecs *default_monspecs;
- u32 pseudo_palette[16];
-
- struct atmel_lcdfb_config *config;
};
#define ATMEL_LCDC_DMABADDR1 0x00
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
---
arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
arch/arm/mach-at91/board-sam9261ek.c | 6 +-
arch/arm/mach-at91/board-sam9263ek.c | 4 +-
arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
arch/arm/mach-at91/board-sam9rlek.c | 4 +-
arch/arm/mach-at91/board.h | 4 +-
arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
arch/avr32/boards/atngw100/mrmt.c | 4 +-
arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
arch/avr32/boards/atstk1000/setup.c | 2 +-
arch/avr32/boards/favr-32/setup.c | 2 +-
arch/avr32/boards/hammerhead/setup.c | 2 +-
arch/avr32/boards/merisc/display.c | 2 +-
arch/avr32/boards/mimc200/setup.c | 4 +-
arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
include/video/atmel_lcdc.h | 24 +------
21 files changed, 109 insertions(+), 101 deletions(-)
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 629ea5f..b2a3474 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -465,7 +465,7 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -498,7 +498,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data) {
return;
@@ -559,7 +559,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 858c8aa..4aeaddd 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -832,7 +832,7 @@ void __init at91_add_device_can(struct at91_can_data *data) {}
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -859,7 +859,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data)
return;
@@ -891,7 +891,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index fe626d4..82636c7 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -965,7 +965,7 @@ void __init at91_add_device_isi(struct isi_platform_data *data,
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -991,7 +991,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data)
return;
@@ -1037,7 +1037,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index 352468f..a698bda 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -498,7 +498,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -525,7 +525,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data) {
return;
@@ -557,7 +557,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index b446645..c819e29 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -405,7 +405,7 @@ static void at91_lcdc_stn_power_control(int on)
}
}
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.default_bpp = 1,
.default_dmacon = ATMEL_LCDC_DMAEN,
.default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
@@ -460,7 +460,7 @@ static void at91_lcdc_tft_power_control(int on)
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
}
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -475,7 +475,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
#endif
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 3284df0..0fdae3f 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -281,7 +281,7 @@ static void at91_lcdc_power_control(int on)
}
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -292,7 +292,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index 2a94896..ef39078 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -284,7 +284,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 32,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -295,7 +295,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index aa265dc..b77d7a9 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -179,7 +179,7 @@ static void at91_lcdc_power_control(int on)
}
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -191,7 +191,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h
index 4a234fb..6c08b34 100644
--- a/arch/arm/mach-at91/board.h
+++ b/arch/arm/mach-at91/board.h
@@ -107,8 +107,8 @@ extern void __init at91_add_device_pwm(u32 mask);
extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
/* LCD Controller */
-struct atmel_lcdfb_info;
-extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
+struct atmel_lcdfb_pdata;
+extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
/* AC97 */
extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index 2038875..dc42804 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -58,7 +58,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 28330000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -96,7 +96,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 7000000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -134,7 +134,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 6400000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c
index f914319..ccc9599 100644
--- a/arch/avr32/boards/atngw100/mrmt.c
+++ b/arch/avr32/boards/atngw100/mrmt.c
@@ -83,7 +83,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
.dclkmax = 9260000,
};
-static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -126,7 +126,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
.dclkmax = 9260000,
};
-static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
index 9392d32..653cc09 100644
--- a/arch/avr32/boards/atstk1000/atstk1000.h
+++ b/arch/avr32/boards/atstk1000/atstk1000.h
@@ -10,7 +10,7 @@
#ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
#define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
-extern struct atmel_lcdfb_info atstk1000_lcdc_data;
+extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
void atstk1000_setup_j2_leds(void);
diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
index 2d6b560..b6b88f5 100644
--- a/arch/avr32/boards/atstk1000/setup.c
+++ b/arch/avr32/boards/atstk1000/setup.c
@@ -55,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = {
.dclkmax = 30000000,
};
-struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
index 27bd6fb..7b1f2cd 100644
--- a/arch/avr32/boards/favr-32/setup.c
+++ b/arch/avr32/boards/favr-32/setup.c
@@ -125,7 +125,7 @@ static struct fb_monspecs __initdata favr32_default_monspecs = {
.dclkmax = 28000000,
};
-struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata favr32_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
index 9d1efd1..dc0e317 100644
--- a/arch/avr32/boards/hammerhead/setup.c
+++ b/arch/avr32/boards/hammerhead/setup.c
@@ -77,7 +77,7 @@ static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
.dclkmax = 10000000,
};
-struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata hammerhead_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
index 85a543c..e7683ee 100644
--- a/arch/avr32/boards/merisc/display.c
+++ b/arch/avr32/boards/merisc/display.c
@@ -45,7 +45,7 @@ static struct fb_monspecs merisc_fb_monspecs = {
.dclkmax = 30000000,
};
-struct atmel_lcdfb_info merisc_lcdc_data = {
+struct atmel_lcdfb_pdata merisc_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
index 05358aa..1cb8e9c 100644
--- a/arch/avr32/boards/mimc200/setup.c
+++ b/arch/avr32/boards/mimc200/setup.c
@@ -8,7 +8,7 @@
* published by the Free Software Foundation.
*/
-extern struct atmel_lcdfb_info mimc200_lcdc_data;
+extern struct atmel_lcdfb_pdata mimc200_lcdc_data;
#include <linux/clk.h>
#include <linux/etherdevice.h>
@@ -71,7 +71,7 @@ static struct fb_monspecs __initdata mimc200_default_monspecs = {
.dclkmax = 25200000,
};
-struct atmel_lcdfb_info __initdata mimc200_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata mimc200_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 7c2f668..0badb05 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1437,7 +1437,7 @@ fail:
* LCDC
* -------------------------------------------------------------------- */
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
-static struct atmel_lcdfb_info atmel_lcdfb0_data;
+static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
static struct resource atmel_lcdfb0_resource[] = {
{
.start = 0xff000000,
@@ -1465,12 +1465,12 @@ static struct clk atmel_lcdfb0_pixclk = {
};
struct platform_device *__init
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
unsigned long fbmem_start, unsigned long fbmem_len,
u64 pin_mask)
{
struct platform_device *pdev;
- struct atmel_lcdfb_info *info;
+ struct atmel_lcdfb_pdata *info;
struct fb_monspecs *monspecs;
struct fb_videomode *modedb;
unsigned int modedb_size;
@@ -1527,7 +1527,7 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
}
info = pdev->dev.platform_data;
- memcpy(info, data, sizeof(struct atmel_lcdfb_info));
+ memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
info->default_monspecs = monspecs;
pdev->name = "at32ap-lcdfb";
diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h
index d485b03..f1a316d 100644
--- a/arch/avr32/mach-at32ap/include/mach/board.h
+++ b/arch/avr32/mach-at32ap/include/mach/board.h
@@ -44,9 +44,9 @@ struct platform_device *
at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
void at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n);
-struct atmel_lcdfb_info;
+struct atmel_lcdfb_pdata;
struct platform_device *
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
unsigned long fbmem_start, unsigned long fbmem_len,
u64 pin_mask);
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index c1a2914..98733cd4 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -20,12 +20,45 @@
#include <linux/gfp.h>
#include <linux/module.h>
#include <linux/platform_data/atmel.h>
+#include <video/of_display_timing.h>
#include <mach/cpu.h>
#include <asm/gpio.h>
#include <video/atmel_lcdc.h>
+struct atmel_lcdfb_config {
+ bool have_alt_pixclock;
+ bool have_hozval;
+ bool have_intensity_bit;
+};
+
+ /* LCD Controller info data structure, stored in device platform_data */
+struct atmel_lcdfb_info {
+ spinlock_t lock;
+ struct fb_info *info;
+ void __iomem *mmio;
+ int irq_base;
+ struct work_struct task;
+
+ unsigned int smem_len;
+ struct platform_device *pdev;
+ struct clk *bus_clk;
+ struct clk *lcdc_clk;
+
+ struct backlight_device *backlight;
+ u8 bl_power;
+ bool lcdcon_pol_negative;
+ u8 saved_lcdcon;
+
+ u32 pseudo_palette[16];
+ bool have_intensity_bit;
+
+ struct atmel_lcdfb_pdata pdata;
+
+ struct atmel_lcdfb_config *config;
+};
+
#define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
#define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
@@ -34,12 +67,6 @@
#define ATMEL_LCDC_DMA_BURST_LEN 8 /* words */
#define ATMEL_LCDC_FIFO_SIZE 512 /* words */
-struct atmel_lcdfb_config {
- bool have_alt_pixclock;
- bool have_hozval;
- bool have_intensity_bit;
-};
-
static struct atmel_lcdfb_config at91sam9261_config = {
.have_hozval = true,
.have_intensity_bit = true,
@@ -242,6 +269,8 @@ static void exit_backlight(struct atmel_lcdfb_info *sinfo)
static void init_contrast(struct atmel_lcdfb_info *sinfo)
{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
/* contrast pwm can be 'inverted' */
if (sinfo->lcdcon_pol_negative)
contrast_ctr &= ~(ATMEL_LCDC_POL_POSITIVE);
@@ -250,7 +279,7 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
- if (sinfo->lcdcon_is_backlight)
+ if (pdata->lcdcon_is_backlight)
init_backlight(sinfo);
}
@@ -293,9 +322,11 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
static void atmel_lcdfb_stop_nowait(struct atmel_lcdfb_info *sinfo)
{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
/* Turn off the LCD controller and the DMA controller */
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
- sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
+ pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
/* Wait for the LCDC core to become idle */
while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
@@ -315,9 +346,11 @@ static void atmel_lcdfb_stop(struct atmel_lcdfb_info *sinfo)
static void atmel_lcdfb_start(struct atmel_lcdfb_info *sinfo)
{
- lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
+ lcdc_writel(sinfo, ATMEL_LCDC_DMACON, pdata->default_dmacon);
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
- (sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
+ (pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
| ATMEL_LCDC_PWR);
}
@@ -418,6 +451,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
{
struct device *dev = info->device;
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned long clk_value_khz;
clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
@@ -501,7 +535,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
else
var->green.length = 6;
- if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
/* RGB:5X5 mode */
var->red.offset = var->green.length + 5;
var->blue.offset = 0;
@@ -518,7 +552,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
var->transp.length = 8;
/* fall through */
case 24:
- if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
/* RGB:888 mode */
var->red.offset = 16;
var->blue.offset = 0;
@@ -567,6 +601,7 @@ static void atmel_lcdfb_reset(struct atmel_lcdfb_info *sinfo)
static int atmel_lcdfb_set_par(struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned long hozval_linesz;
unsigned long value;
unsigned long clk_value_khz;
@@ -628,7 +663,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
/* Initialize control register 2 */
- value = sinfo->default_lcdcon2;
+ value = pdata->default_lcdcon2;
if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
value |= ATMEL_LCDC_INVLINE_INVERTED;
@@ -732,6 +767,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
unsigned int transp, struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned int val;
u32 *pal;
int ret = 1;
@@ -768,8 +804,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
*/
} else {
/* new style BGR:565 / RGB:565 */
- if (sinfo->lcd_wiring_mode =
- ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
val = ((blue >> 11) & 0x001f);
val |= ((red >> 0) & 0xf800);
} else {
@@ -909,7 +944,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct fb_info *info;
struct atmel_lcdfb_info *sinfo;
- struct atmel_lcdfb_info *pdata_sinfo;
+ struct atmel_lcdfb_pdata *pdata;
struct fb_videomode fbmode;
struct resource *regs = NULL;
struct resource *map = NULL;
@@ -927,17 +962,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
sinfo = info->par;
if (dev->platform_data) {
- pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
- sinfo->default_bpp = pdata_sinfo->default_bpp;
- sinfo->default_dmacon = pdata_sinfo->default_dmacon;
- sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
- sinfo->default_monspecs = pdata_sinfo->default_monspecs;
- sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
- sinfo->guard_time = pdata_sinfo->guard_time;
- sinfo->smem_len = pdata_sinfo->smem_len;
- sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
- sinfo->lcdcon_pol_negative = pdata_sinfo->lcdcon_pol_negative;
- sinfo->lcd_wiring_mode = pdata_sinfo->lcd_wiring_mode;
+ pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
+ sinfo->pdata = *pdata;
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
@@ -953,7 +979,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
info->pseudo_palette = sinfo->pseudo_palette;
info->fbops = &atmel_lcdfb_ops;
- memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
+ memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
info->fix = atmel_lcdfb_fix;
/* Enable LCDC Clocks */
@@ -971,7 +997,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
info->monspecs.modedb_len, info->monspecs.modedb,
- sinfo->default_bpp);
+ pdata->default_bpp);
if (!ret) {
dev_err(dev, "no suitable video mode found\n");
goto stop_clk;
@@ -1088,8 +1114,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
fb_add_videomode(&fbmode, &info->modelist);
/* Power up the LCDC screen */
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(1);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(1);
dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
@@ -1134,15 +1160,17 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct fb_info *info = dev_get_drvdata(dev);
struct atmel_lcdfb_info *sinfo;
+ struct atmel_lcdfb_pdata *pdata;
if (!info || !info->par)
return 0;
sinfo = info->par;
+ pdata = &sinfo->pdata;
cancel_work_sync(&sinfo->task);
exit_backlight(sinfo);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(0);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(0);
unregister_framebuffer(info);
atmel_lcdfb_stop_clock(sinfo);
clk_put(sinfo->lcdc_clk);
@@ -1170,6 +1198,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
/*
* We don't want to handle interrupts while the clock is
@@ -1179,8 +1208,8 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(0);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(0);
atmel_lcdfb_stop(sinfo);
atmel_lcdfb_stop_clock(sinfo);
@@ -1192,11 +1221,12 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
atmel_lcdfb_start_clock(sinfo);
atmel_lcdfb_start(sinfo);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(1);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(1);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
/* Enable FIFO & DMA errors */
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 0f5a2fc..2eb601c 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -31,39 +31,17 @@
#define ATMEL_LCDC_WIRING_BGR 0
#define ATMEL_LCDC_WIRING_RGB 1
-struct atmel_lcdfb_config;
/* LCD Controller info data structure, stored in device platform_data */
-struct atmel_lcdfb_info {
- spinlock_t lock;
- struct fb_info *info;
- void __iomem *mmio;
- int irq_base;
- struct work_struct task;
-
+struct atmel_lcdfb_pdata {
unsigned int guard_time;
- unsigned int smem_len;
- struct platform_device *pdev;
- struct clk *bus_clk;
- struct clk *lcdc_clk;
-
-#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
- struct backlight_device *backlight;
- u8 bl_power;
-#endif
bool lcdcon_is_backlight;
- bool lcdcon_pol_negative;
- u8 saved_lcdcon;
-
u8 default_bpp;
u8 lcd_wiring_mode;
unsigned int default_lcdcon2;
unsigned int default_dmacon;
void (*atmel_lcdfb_power_control)(int on);
struct fb_monspecs *default_monspecs;
- u32 pseudo_palette[16];
-
- struct atmel_lcdfb_config *config;
};
#define ATMEL_LCDC_DMABADDR1 0x00
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev at vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
---
arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
arch/arm/mach-at91/board-sam9261ek.c | 6 +-
arch/arm/mach-at91/board-sam9263ek.c | 4 +-
arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
arch/arm/mach-at91/board-sam9rlek.c | 4 +-
arch/arm/mach-at91/board.h | 4 +-
arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
arch/avr32/boards/atngw100/mrmt.c | 4 +-
arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
arch/avr32/boards/atstk1000/setup.c | 2 +-
arch/avr32/boards/favr-32/setup.c | 2 +-
arch/avr32/boards/hammerhead/setup.c | 2 +-
arch/avr32/boards/merisc/display.c | 2 +-
arch/avr32/boards/mimc200/setup.c | 4 +-
arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
include/video/atmel_lcdc.h | 24 +------
21 files changed, 109 insertions(+), 101 deletions(-)
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 629ea5f..b2a3474 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -465,7 +465,7 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -498,7 +498,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data) {
return;
@@ -559,7 +559,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 858c8aa..4aeaddd 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -832,7 +832,7 @@ void __init at91_add_device_can(struct at91_can_data *data) {}
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -859,7 +859,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data)
return;
@@ -891,7 +891,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index fe626d4..82636c7 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -965,7 +965,7 @@ void __init at91_add_device_isi(struct isi_platform_data *data,
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -991,7 +991,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data)
return;
@@ -1037,7 +1037,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index 352468f..a698bda 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -498,7 +498,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_info lcdc_data;
+static struct atmel_lcdfb_pdata lcdc_data;
static struct resource lcdc_resources[] = {
[0] = {
@@ -525,7 +525,7 @@ static struct platform_device at91_lcdc_device = {
.num_resources = ARRAY_SIZE(lcdc_resources),
};
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
{
if (!data) {
return;
@@ -557,7 +557,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
platform_device_register(&at91_lcdc_device);
}
#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
+void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
#endif
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index b446645..c819e29 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -405,7 +405,7 @@ static void at91_lcdc_stn_power_control(int on)
}
}
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.default_bpp = 1,
.default_dmacon = ATMEL_LCDC_DMAEN,
.default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
@@ -460,7 +460,7 @@ static void at91_lcdc_tft_power_control(int on)
at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
}
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -475,7 +475,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
#endif
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 3284df0..0fdae3f 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -281,7 +281,7 @@ static void at91_lcdc_power_control(int on)
}
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -292,7 +292,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index 2a94896..ef39078 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -284,7 +284,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 32,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -295,7 +295,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index aa265dc..b77d7a9 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -179,7 +179,7 @@ static void at91_lcdc_power_control(int on)
}
/* Driver datas */
-static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
.lcdcon_is_backlight = true,
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
@@ -191,7 +191,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
};
#else
-static struct atmel_lcdfb_info __initdata ek_lcdc_data;
+static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
#endif
diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h
index 4a234fb..6c08b34 100644
--- a/arch/arm/mach-at91/board.h
+++ b/arch/arm/mach-at91/board.h
@@ -107,8 +107,8 @@ extern void __init at91_add_device_pwm(u32 mask);
extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
/* LCD Controller */
-struct atmel_lcdfb_info;
-extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
+struct atmel_lcdfb_pdata;
+extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
/* AC97 */
extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index 2038875..dc42804 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -58,7 +58,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 28330000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -96,7 +96,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 7000000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -134,7 +134,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
.dclkmax = 6400000,
};
-static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c
index f914319..ccc9599 100644
--- a/arch/avr32/boards/atngw100/mrmt.c
+++ b/arch/avr32/boards/atngw100/mrmt.c
@@ -83,7 +83,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
.dclkmax = 9260000,
};
-static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
@@ -126,7 +126,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
.dclkmax = 9260000,
};
-static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
+static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
index 9392d32..653cc09 100644
--- a/arch/avr32/boards/atstk1000/atstk1000.h
+++ b/arch/avr32/boards/atstk1000/atstk1000.h
@@ -10,7 +10,7 @@
#ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
#define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
-extern struct atmel_lcdfb_info atstk1000_lcdc_data;
+extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
void atstk1000_setup_j2_leds(void);
diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
index 2d6b560..b6b88f5 100644
--- a/arch/avr32/boards/atstk1000/setup.c
+++ b/arch/avr32/boards/atstk1000/setup.c
@@ -55,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = {
.dclkmax = 30000000,
};
-struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
index 27bd6fb..7b1f2cd 100644
--- a/arch/avr32/boards/favr-32/setup.c
+++ b/arch/avr32/boards/favr-32/setup.c
@@ -125,7 +125,7 @@ static struct fb_monspecs __initdata favr32_default_monspecs = {
.dclkmax = 28000000,
};
-struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata favr32_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
index 9d1efd1..dc0e317 100644
--- a/arch/avr32/boards/hammerhead/setup.c
+++ b/arch/avr32/boards/hammerhead/setup.c
@@ -77,7 +77,7 @@ static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
.dclkmax = 10000000,
};
-struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata hammerhead_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
index 85a543c..e7683ee 100644
--- a/arch/avr32/boards/merisc/display.c
+++ b/arch/avr32/boards/merisc/display.c
@@ -45,7 +45,7 @@ static struct fb_monspecs merisc_fb_monspecs = {
.dclkmax = 30000000,
};
-struct atmel_lcdfb_info merisc_lcdc_data = {
+struct atmel_lcdfb_pdata merisc_lcdc_data = {
.default_bpp = 24,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
index 05358aa..1cb8e9c 100644
--- a/arch/avr32/boards/mimc200/setup.c
+++ b/arch/avr32/boards/mimc200/setup.c
@@ -8,7 +8,7 @@
* published by the Free Software Foundation.
*/
-extern struct atmel_lcdfb_info mimc200_lcdc_data;
+extern struct atmel_lcdfb_pdata mimc200_lcdc_data;
#include <linux/clk.h>
#include <linux/etherdevice.h>
@@ -71,7 +71,7 @@ static struct fb_monspecs __initdata mimc200_default_monspecs = {
.dclkmax = 25200000,
};
-struct atmel_lcdfb_info __initdata mimc200_lcdc_data = {
+struct atmel_lcdfb_pdata __initdata mimc200_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
.default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 7c2f668..0badb05 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -1437,7 +1437,7 @@ fail:
* LCDC
* -------------------------------------------------------------------- */
#if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
-static struct atmel_lcdfb_info atmel_lcdfb0_data;
+static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
static struct resource atmel_lcdfb0_resource[] = {
{
.start = 0xff000000,
@@ -1465,12 +1465,12 @@ static struct clk atmel_lcdfb0_pixclk = {
};
struct platform_device *__init
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
unsigned long fbmem_start, unsigned long fbmem_len,
u64 pin_mask)
{
struct platform_device *pdev;
- struct atmel_lcdfb_info *info;
+ struct atmel_lcdfb_pdata *info;
struct fb_monspecs *monspecs;
struct fb_videomode *modedb;
unsigned int modedb_size;
@@ -1527,7 +1527,7 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
}
info = pdev->dev.platform_data;
- memcpy(info, data, sizeof(struct atmel_lcdfb_info));
+ memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
info->default_monspecs = monspecs;
pdev->name = "at32ap-lcdfb";
diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h
index d485b03..f1a316d 100644
--- a/arch/avr32/mach-at32ap/include/mach/board.h
+++ b/arch/avr32/mach-at32ap/include/mach/board.h
@@ -44,9 +44,9 @@ struct platform_device *
at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
void at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n);
-struct atmel_lcdfb_info;
+struct atmel_lcdfb_pdata;
struct platform_device *
-at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
unsigned long fbmem_start, unsigned long fbmem_len,
u64 pin_mask);
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index c1a2914..98733cd4 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -20,12 +20,45 @@
#include <linux/gfp.h>
#include <linux/module.h>
#include <linux/platform_data/atmel.h>
+#include <video/of_display_timing.h>
#include <mach/cpu.h>
#include <asm/gpio.h>
#include <video/atmel_lcdc.h>
+struct atmel_lcdfb_config {
+ bool have_alt_pixclock;
+ bool have_hozval;
+ bool have_intensity_bit;
+};
+
+ /* LCD Controller info data structure, stored in device platform_data */
+struct atmel_lcdfb_info {
+ spinlock_t lock;
+ struct fb_info *info;
+ void __iomem *mmio;
+ int irq_base;
+ struct work_struct task;
+
+ unsigned int smem_len;
+ struct platform_device *pdev;
+ struct clk *bus_clk;
+ struct clk *lcdc_clk;
+
+ struct backlight_device *backlight;
+ u8 bl_power;
+ bool lcdcon_pol_negative;
+ u8 saved_lcdcon;
+
+ u32 pseudo_palette[16];
+ bool have_intensity_bit;
+
+ struct atmel_lcdfb_pdata pdata;
+
+ struct atmel_lcdfb_config *config;
+};
+
#define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
#define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
@@ -34,12 +67,6 @@
#define ATMEL_LCDC_DMA_BURST_LEN 8 /* words */
#define ATMEL_LCDC_FIFO_SIZE 512 /* words */
-struct atmel_lcdfb_config {
- bool have_alt_pixclock;
- bool have_hozval;
- bool have_intensity_bit;
-};
-
static struct atmel_lcdfb_config at91sam9261_config = {
.have_hozval = true,
.have_intensity_bit = true,
@@ -242,6 +269,8 @@ static void exit_backlight(struct atmel_lcdfb_info *sinfo)
static void init_contrast(struct atmel_lcdfb_info *sinfo)
{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
/* contrast pwm can be 'inverted' */
if (sinfo->lcdcon_pol_negative)
contrast_ctr &= ~(ATMEL_LCDC_POL_POSITIVE);
@@ -250,7 +279,7 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
- if (sinfo->lcdcon_is_backlight)
+ if (pdata->lcdcon_is_backlight)
init_backlight(sinfo);
}
@@ -293,9 +322,11 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
static void atmel_lcdfb_stop_nowait(struct atmel_lcdfb_info *sinfo)
{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
/* Turn off the LCD controller and the DMA controller */
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
- sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
+ pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
/* Wait for the LCDC core to become idle */
while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
@@ -315,9 +346,11 @@ static void atmel_lcdfb_stop(struct atmel_lcdfb_info *sinfo)
static void atmel_lcdfb_start(struct atmel_lcdfb_info *sinfo)
{
- lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
+ lcdc_writel(sinfo, ATMEL_LCDC_DMACON, pdata->default_dmacon);
lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
- (sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
+ (pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
| ATMEL_LCDC_PWR);
}
@@ -418,6 +451,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
{
struct device *dev = info->device;
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned long clk_value_khz;
clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
@@ -501,7 +535,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
else
var->green.length = 6;
- if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
/* RGB:5X5 mode */
var->red.offset = var->green.length + 5;
var->blue.offset = 0;
@@ -518,7 +552,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
var->transp.length = 8;
/* fall through */
case 24:
- if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
/* RGB:888 mode */
var->red.offset = 16;
var->blue.offset = 0;
@@ -567,6 +601,7 @@ static void atmel_lcdfb_reset(struct atmel_lcdfb_info *sinfo)
static int atmel_lcdfb_set_par(struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned long hozval_linesz;
unsigned long value;
unsigned long clk_value_khz;
@@ -628,7 +663,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
/* Initialize control register 2 */
- value = sinfo->default_lcdcon2;
+ value = pdata->default_lcdcon2;
if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
value |= ATMEL_LCDC_INVLINE_INVERTED;
@@ -732,6 +767,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
unsigned int transp, struct fb_info *info)
{
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
unsigned int val;
u32 *pal;
int ret = 1;
@@ -768,8 +804,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
*/
} else {
/* new style BGR:565 / RGB:565 */
- if (sinfo->lcd_wiring_mode ==
- ATMEL_LCDC_WIRING_RGB) {
+ if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
val = ((blue >> 11) & 0x001f);
val |= ((red >> 0) & 0xf800);
} else {
@@ -909,7 +944,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct fb_info *info;
struct atmel_lcdfb_info *sinfo;
- struct atmel_lcdfb_info *pdata_sinfo;
+ struct atmel_lcdfb_pdata *pdata;
struct fb_videomode fbmode;
struct resource *regs = NULL;
struct resource *map = NULL;
@@ -927,17 +962,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
sinfo = info->par;
if (dev->platform_data) {
- pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
- sinfo->default_bpp = pdata_sinfo->default_bpp;
- sinfo->default_dmacon = pdata_sinfo->default_dmacon;
- sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
- sinfo->default_monspecs = pdata_sinfo->default_monspecs;
- sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
- sinfo->guard_time = pdata_sinfo->guard_time;
- sinfo->smem_len = pdata_sinfo->smem_len;
- sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
- sinfo->lcdcon_pol_negative = pdata_sinfo->lcdcon_pol_negative;
- sinfo->lcd_wiring_mode = pdata_sinfo->lcd_wiring_mode;
+ pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
+ sinfo->pdata = *pdata;
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
@@ -953,7 +979,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
info->pseudo_palette = sinfo->pseudo_palette;
info->fbops = &atmel_lcdfb_ops;
- memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
+ memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
info->fix = atmel_lcdfb_fix;
/* Enable LCDC Clocks */
@@ -971,7 +997,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
info->monspecs.modedb_len, info->monspecs.modedb,
- sinfo->default_bpp);
+ pdata->default_bpp);
if (!ret) {
dev_err(dev, "no suitable video mode found\n");
goto stop_clk;
@@ -1088,8 +1114,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
fb_add_videomode(&fbmode, &info->modelist);
/* Power up the LCDC screen */
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(1);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(1);
dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
@@ -1134,15 +1160,17 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct fb_info *info = dev_get_drvdata(dev);
struct atmel_lcdfb_info *sinfo;
+ struct atmel_lcdfb_pdata *pdata;
if (!info || !info->par)
return 0;
sinfo = info->par;
+ pdata = &sinfo->pdata;
cancel_work_sync(&sinfo->task);
exit_backlight(sinfo);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(0);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(0);
unregister_framebuffer(info);
atmel_lcdfb_stop_clock(sinfo);
clk_put(sinfo->lcdc_clk);
@@ -1170,6 +1198,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
/*
* We don't want to handle interrupts while the clock is
@@ -1179,8 +1208,8 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(0);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(0);
atmel_lcdfb_stop(sinfo);
atmel_lcdfb_stop_clock(sinfo);
@@ -1192,11 +1221,12 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
atmel_lcdfb_start_clock(sinfo);
atmel_lcdfb_start(sinfo);
- if (sinfo->atmel_lcdfb_power_control)
- sinfo->atmel_lcdfb_power_control(1);
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(1);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
/* Enable FIFO & DMA errors */
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 0f5a2fc..2eb601c 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -31,39 +31,17 @@
#define ATMEL_LCDC_WIRING_BGR 0
#define ATMEL_LCDC_WIRING_RGB 1
-struct atmel_lcdfb_config;
/* LCD Controller info data structure, stored in device platform_data */
-struct atmel_lcdfb_info {
- spinlock_t lock;
- struct fb_info *info;
- void __iomem *mmio;
- int irq_base;
- struct work_struct task;
-
+struct atmel_lcdfb_pdata {
unsigned int guard_time;
- unsigned int smem_len;
- struct platform_device *pdev;
- struct clk *bus_clk;
- struct clk *lcdc_clk;
-
-#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
- struct backlight_device *backlight;
- u8 bl_power;
-#endif
bool lcdcon_is_backlight;
- bool lcdcon_pol_negative;
- u8 saved_lcdcon;
-
u8 default_bpp;
u8 lcd_wiring_mode;
unsigned int default_lcdcon2;
unsigned int default_dmacon;
void (*atmel_lcdfb_power_control)(int on);
struct fb_monspecs *default_monspecs;
- u32 pseudo_palette[16];
-
- struct atmel_lcdfb_config *config;
};
#define ATMEL_LCDC_DMABADDR1 0x00
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss,
Jean-Christophe PLAGNIOL-VILLARD, linux-fbdev, Andrew Morton
to simplify the check on the presence of the callback
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
drivers/video/atmel_lcdfb.c | 22 +++++++++++-----------
1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 98733cd4..9574c47 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -283,6 +283,13 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
init_backlight(sinfo);
}
+static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int on)
+{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(on);
+}
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
.type = FB_TYPE_PACKED_PIXELS,
@@ -1114,8 +1121,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
fb_add_videomode(&fbmode, &info->modelist);
/* Power up the LCDC screen */
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(1);
+ atmel_lcdfb_power_control(sinfo, 1);
dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
@@ -1169,8 +1175,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
cancel_work_sync(&sinfo->task);
exit_backlight(sinfo);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(0);
+ atmel_lcdfb_power_control(sinfo, 0);
unregister_framebuffer(info);
atmel_lcdfb_stop_clock(sinfo);
clk_put(sinfo->lcdc_clk);
@@ -1198,7 +1203,6 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
- struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
/*
* We don't want to handle interrupts while the clock is
@@ -1208,9 +1212,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(0);
-
+ atmel_lcdfb_power_control(sinfo, 0);
atmel_lcdfb_stop(sinfo);
atmel_lcdfb_stop_clock(sinfo);
@@ -1221,12 +1223,10 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
- struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
atmel_lcdfb_start_clock(sinfo);
atmel_lcdfb_start(sinfo);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(1);
+ atmel_lcdfb_power_control(sinfo, 1);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
/* Enable FIFO & DMA errors */
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
to simplify the check on the presence of the callback
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
drivers/video/atmel_lcdfb.c | 22 +++++++++++-----------
1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 98733cd4..9574c47 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -283,6 +283,13 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
init_backlight(sinfo);
}
+static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int on)
+{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(on);
+}
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
.type = FB_TYPE_PACKED_PIXELS,
@@ -1114,8 +1121,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
fb_add_videomode(&fbmode, &info->modelist);
/* Power up the LCDC screen */
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(1);
+ atmel_lcdfb_power_control(sinfo, 1);
dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
@@ -1169,8 +1175,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
cancel_work_sync(&sinfo->task);
exit_backlight(sinfo);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(0);
+ atmel_lcdfb_power_control(sinfo, 0);
unregister_framebuffer(info);
atmel_lcdfb_stop_clock(sinfo);
clk_put(sinfo->lcdc_clk);
@@ -1198,7 +1203,6 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
- struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
/*
* We don't want to handle interrupts while the clock is
@@ -1208,9 +1212,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(0);
-
+ atmel_lcdfb_power_control(sinfo, 0);
atmel_lcdfb_stop(sinfo);
atmel_lcdfb_stop_clock(sinfo);
@@ -1221,12 +1223,10 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
- struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
atmel_lcdfb_start_clock(sinfo);
atmel_lcdfb_start(sinfo);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(1);
+ atmel_lcdfb_power_control(sinfo, 1);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
/* Enable FIFO & DMA errors */
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
to simplify the check on the presence of the callback
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev at vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
drivers/video/atmel_lcdfb.c | 22 +++++++++++-----------
1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 98733cd4..9574c47 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -283,6 +283,13 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
init_backlight(sinfo);
}
+static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int on)
+{
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+
+ if (pdata->atmel_lcdfb_power_control)
+ pdata->atmel_lcdfb_power_control(on);
+}
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
.type = FB_TYPE_PACKED_PIXELS,
@@ -1114,8 +1121,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
fb_add_videomode(&fbmode, &info->modelist);
/* Power up the LCDC screen */
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(1);
+ atmel_lcdfb_power_control(sinfo, 1);
dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
@@ -1169,8 +1175,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
cancel_work_sync(&sinfo->task);
exit_backlight(sinfo);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(0);
+ atmel_lcdfb_power_control(sinfo, 0);
unregister_framebuffer(info);
atmel_lcdfb_stop_clock(sinfo);
clk_put(sinfo->lcdc_clk);
@@ -1198,7 +1203,6 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
- struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
/*
* We don't want to handle interrupts while the clock is
@@ -1208,9 +1212,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(0);
-
+ atmel_lcdfb_power_control(sinfo, 0);
atmel_lcdfb_stop(sinfo);
atmel_lcdfb_stop_clock(sinfo);
@@ -1221,12 +1223,10 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
{
struct fb_info *info = platform_get_drvdata(pdev);
struct atmel_lcdfb_info *sinfo = info->par;
- struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
atmel_lcdfb_start_clock(sinfo);
atmel_lcdfb_start(sinfo);
- if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(1);
+ atmel_lcdfb_power_control(sinfo, 1);
lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
/* Enable FIFO & DMA errors */
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss,
Jean-Christophe PLAGNIOL-VILLARD, linux-fbdev, Andrew Morton
so we can use have list gpio as example (probe via DT)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
arch/arm/mach-at91/board-sam9261ek.c | 4 ++--
arch/arm/mach-at91/board-sam9263ek.c | 2 +-
arch/arm/mach-at91/board-sam9rlek.c | 2 +-
arch/avr32/boards/atngw100/evklcd10x.c | 2 +-
drivers/video/atmel_lcdfb.c | 2 +-
include/video/atmel_lcdc.h | 4 +++-
6 files changed, 9 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index c819e29..9a6618a 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -393,7 +393,7 @@ static struct fb_monspecs at91fb_default_stn_monspecs = {
| ATMEL_LCDC_IFWIDTH_4 \
| ATMEL_LCDC_SCANMOD_SINGLE)
-static void at91_lcdc_stn_power_control(int on)
+static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
/* backlight */
if (on) { /* power up */
@@ -452,7 +452,7 @@ static struct fb_monspecs at91fb_default_tft_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_tft_power_control(int on)
+static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 0fdae3f..8b4942c 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -275,7 +275,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
at91_set_gpio_value(AT91_PIN_PA30, on);
}
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index b77d7a9..604eecf 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -170,7 +170,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PC1, 0); /* power up */
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index dc42804..64919b0 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -145,7 +145,7 @@ static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
};
#endif
-static void atevklcd10x_lcdc_power_control(int on)
+static void atevklcd10x_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
gpio_set_value(GPIO_PIN_PB(15), on);
}
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 9574c47..f67e226 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -288,7 +288,7 @@ static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int
struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(on);
+ pdata->atmel_lcdfb_power_control(pdata, on);
}
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 2eb601c..f624c51 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -40,8 +40,10 @@ struct atmel_lcdfb_pdata {
u8 lcd_wiring_mode;
unsigned int default_lcdcon2;
unsigned int default_dmacon;
- void (*atmel_lcdfb_power_control)(int on);
+ void (*atmel_lcdfb_power_control)(struct atmel_lcdfb_pdata *pdata, int on);
struct fb_monspecs *default_monspecs;
+
+ struct list_head pwr_gpios;
};
#define ATMEL_LCDC_DMABADDR1 0x00
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
so we can use have list gpio as example (probe via DT)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
arch/arm/mach-at91/board-sam9261ek.c | 4 ++--
arch/arm/mach-at91/board-sam9263ek.c | 2 +-
arch/arm/mach-at91/board-sam9rlek.c | 2 +-
arch/avr32/boards/atngw100/evklcd10x.c | 2 +-
drivers/video/atmel_lcdfb.c | 2 +-
include/video/atmel_lcdc.h | 4 +++-
6 files changed, 9 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index c819e29..9a6618a 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -393,7 +393,7 @@ static struct fb_monspecs at91fb_default_stn_monspecs = {
| ATMEL_LCDC_IFWIDTH_4 \
| ATMEL_LCDC_SCANMOD_SINGLE)
-static void at91_lcdc_stn_power_control(int on)
+static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
/* backlight */
if (on) { /* power up */
@@ -452,7 +452,7 @@ static struct fb_monspecs at91fb_default_tft_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_tft_power_control(int on)
+static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 0fdae3f..8b4942c 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -275,7 +275,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
at91_set_gpio_value(AT91_PIN_PA30, on);
}
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index b77d7a9..604eecf 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -170,7 +170,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PC1, 0); /* power up */
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index dc42804..64919b0 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -145,7 +145,7 @@ static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
};
#endif
-static void atevklcd10x_lcdc_power_control(int on)
+static void atevklcd10x_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
gpio_set_value(GPIO_PIN_PB(15), on);
}
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 9574c47..f67e226 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -288,7 +288,7 @@ static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int
struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(on);
+ pdata->atmel_lcdfb_power_control(pdata, on);
}
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 2eb601c..f624c51 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -40,8 +40,10 @@ struct atmel_lcdfb_pdata {
u8 lcd_wiring_mode;
unsigned int default_lcdcon2;
unsigned int default_dmacon;
- void (*atmel_lcdfb_power_control)(int on);
+ void (*atmel_lcdfb_power_control)(struct atmel_lcdfb_pdata *pdata, int on);
struct fb_monspecs *default_monspecs;
+
+ struct list_head pwr_gpios;
};
#define ATMEL_LCDC_DMABADDR1 0x00
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
so we can use have list gpio as example (probe via DT)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev at vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
arch/arm/mach-at91/board-sam9261ek.c | 4 ++--
arch/arm/mach-at91/board-sam9263ek.c | 2 +-
arch/arm/mach-at91/board-sam9rlek.c | 2 +-
arch/avr32/boards/atngw100/evklcd10x.c | 2 +-
drivers/video/atmel_lcdfb.c | 2 +-
include/video/atmel_lcdc.h | 4 +++-
6 files changed, 9 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index c819e29..9a6618a 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -393,7 +393,7 @@ static struct fb_monspecs at91fb_default_stn_monspecs = {
| ATMEL_LCDC_IFWIDTH_4 \
| ATMEL_LCDC_SCANMOD_SINGLE)
-static void at91_lcdc_stn_power_control(int on)
+static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
/* backlight */
if (on) { /* power up */
@@ -452,7 +452,7 @@ static struct fb_monspecs at91fb_default_tft_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_tft_power_control(int on)
+static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index 0fdae3f..8b4942c 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -275,7 +275,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
at91_set_gpio_value(AT91_PIN_PA30, on);
}
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index b77d7a9..604eecf 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -170,7 +170,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-static void at91_lcdc_power_control(int on)
+static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PC1, 0); /* power up */
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index dc42804..64919b0 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -145,7 +145,7 @@ static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
};
#endif
-static void atevklcd10x_lcdc_power_control(int on)
+static void atevklcd10x_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
{
gpio_set_value(GPIO_PIN_PB(15), on);
}
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index 9574c47..f67e226 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -288,7 +288,7 @@ static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int
struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
if (pdata->atmel_lcdfb_power_control)
- pdata->atmel_lcdfb_power_control(on);
+ pdata->atmel_lcdfb_power_control(pdata, on);
}
static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
index 2eb601c..f624c51 100644
--- a/include/video/atmel_lcdc.h
+++ b/include/video/atmel_lcdc.h
@@ -40,8 +40,10 @@ struct atmel_lcdfb_pdata {
u8 lcd_wiring_mode;
unsigned int default_lcdcon2;
unsigned int default_dmacon;
- void (*atmel_lcdfb_power_control)(int on);
+ void (*atmel_lcdfb_power_control)(struct atmel_lcdfb_pdata *pdata, int on);
struct fb_monspecs *default_monspecs;
+
+ struct list_head pwr_gpios;
};
#define ATMEL_LCDC_DMABADDR1 0x00
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss,
Jean-Christophe PLAGNIOL-VILLARD, linux-fbdev, Andrew Morton
get display timings from device tree
Use videomode helpers to get display timings and configurations from
device tree
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
.../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
drivers/video/Kconfig | 2 +
drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
3 files changed, 289 insertions(+), 32 deletions(-)
create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
new file mode 100644
index 0000000..1ec175e
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
@@ -0,0 +1,75 @@
+Atmel LCDC Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible :
+ "atmel,at91sam9261-lcdc" ,
+ "atmel,at91sam9263-lcdc" ,
+ "atmel,at91sam9g10-lcdc" ,
+ "atmel,at91sam9g45-lcdc" ,
+ "atmel,at91sam9g45es-lcdc" ,
+ "atmel,at91sam9rl-lcdc" ,
+ "atmel,at32ap-lcdc"
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : framebuffer controller interrupt
+- display: a phandle pointing to the display node
+
+Required nodes:
+- display: a display node is required to initialize the lcd panel
+ This should be in the board dts.
+- default-mode: a videomode within the display with timing parameters
+ as specified below.
+
+Example:
+
+ fb0: fb@0x00500000 {
+ compatible = "atmel,at91sam9g45-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ display = <&display0>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ };
+
+Atmel LCDC Display
+-----------------------------------------------------
+Required properties (as per of_videomode_helper):
+
+ - atmel,dmacon: dma controler configuration
+ - atmel,lcdcon2: lcd controler configuration
+ - atmel,guard-time: lcd guard time (Delay in frame periods)
+ - bits-per-pixel: lcd panel bit-depth.
+
+Optional properties (as per of_videomode_helper):
+ - atmel,lcdcon-backlight: enable backlight
+ - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
+ - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
+
+Example:
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 4c1546f..0687482 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1018,6 +1018,8 @@ config FB_ATMEL
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_VIDEOMODE
help
This enables support for the AT91/AT32 LCD Controller.
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index f67e226..4a31570 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -20,7 +20,11 @@
#include <linux/gfp.h>
#include <linux/module.h>
#include <linux/platform_data/atmel.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <video/of_display_timing.h>
+#include <video/videomode.h>
#include <mach/cpu.h>
#include <asm/gpio.h>
@@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
struct atmel_lcdfb_config *config;
};
+struct atmel_lcdfb_power_ctrl_gpio {
+ int gpio;
+ int active_low;
+
+ struct list_head list;
+};
+
#define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
#define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
@@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
clk_disable(sinfo->lcdc_clk);
}
+#ifdef CONFIG_OF
+static const struct of_device_id atmel_lcdfb_dt_ids[] = {
+ { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
+ { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
+ { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
+ { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
+ { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
+ { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
+ { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
+
+static const char *atmel_lcdfb_wiring_modes[] = {
+ [ATMEL_LCDC_WIRING_BGR] = "BRG",
+ [ATMEL_LCDC_WIRING_RGB] = "RGB",
+};
+
+const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
+{
+ const char *mode;
+ int err, i;
+
+ err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
+ if (err < 0)
+ return ATMEL_LCDC_WIRING_BGR;
+
+ for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
+ if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
+ return i;
+
+ return -ENODEV;
+}
+
+static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
+{
+ struct atmel_lcdfb_power_ctrl_gpio *og;
+
+ list_for_each_entry(og, &pdata->pwr_gpios, list)
+ gpio_set_value(og->gpio, on);
+}
+
+static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
+{
+ struct fb_info *info = sinfo->info;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+ struct fb_var_screeninfo *var = &info->var;
+ struct device *dev = &sinfo->pdev->dev;
+ struct device_node *np =dev->of_node;
+ struct device_node *display_np;
+ struct device_node *timings_np;
+ struct display_timings *timings;
+ enum of_gpio_flags flags;
+ struct atmel_lcdfb_power_ctrl_gpio *og;
+ bool is_gpio_power = false;
+ int ret = -ENOENT;
+ int i, gpio;
+
+ sinfo->config = (struct atmel_lcdfb_config*)
+ of_match_device(atmel_lcdfb_dt_ids, dev)->data;
+
+ display_np = of_parse_phandle(np, "display", 0);
+ if (!display_np) {
+ dev_err(dev, "failed to find display phandle\n");
+ return -ENOENT;
+ }
+
+ ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property atmel,guard-time\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property atmel,lcdcon2\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ ret = -ENOMEM;
+ for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
+ gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
+ i, &flags);
+ if (gpio < 0)
+ continue;
+
+ og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
+ if (!og)
+ goto put_display_node;
+
+ og->gpio = gpio;
+ og->active_low = flags & OF_GPIO_ACTIVE_LOW;
+ is_gpio_power = true;
+ ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
+ if (ret) {
+ dev_err(dev, "request gpio %d failed\n", gpio);
+ goto put_display_node;
+ }
+
+ ret = gpio_direction_output(gpio, og->active_low);
+ if (ret) {
+ dev_err(dev, "set direction output gpio %d failed\n", gpio);
+ goto put_display_node;
+ }
+ }
+
+ if (is_gpio_power)
+ pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
+
+ ret = atmel_lcdfb_get_of_wiring_modes(display_np);
+ if (ret < 0) {
+ dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
+ goto put_display_node;
+ }
+ pdata->lcd_wiring_mode = ret;
+
+ pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
+
+ timings = of_get_display_timings(display_np);
+ if (!timings) {
+ dev_err(dev, "failed to get display timings\n");
+ goto put_display_node;
+ }
+
+ timings_np = of_find_node_by_name(display_np, "display-timings");
+ if (!timings_np) {
+ dev_err(dev, "failed to find display-timings node\n");
+ goto put_display_node;
+ }
+
+ for (i = 0; i < of_get_child_count(timings_np); i++) {
+ struct videomode vm;
+ struct fb_videomode fb_vm;
+
+ ret = videomode_from_timing(timings, &vm, i);
+ if (ret < 0)
+ goto put_timings_node;
+ ret = fb_videomode_from_videomode(&vm, &fb_vm);
+ if (ret < 0)
+ goto put_timings_node;
+
+ fb_add_videomode(&fb_vm, &info->modelist);
+ }
+
+ return 0;
+
+put_timings_node:
+ of_node_put(timings_np);
+put_display_node:
+ of_node_put(display_np);
+ return ret;
+}
+#else
+static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
+{
+ return 0;
+}
+#endif
static int __init atmel_lcdfb_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct fb_info *info;
struct atmel_lcdfb_info *sinfo;
- struct atmel_lcdfb_pdata *pdata;
- struct fb_videomode fbmode;
+ struct atmel_lcdfb_pdata *pdata = NULL;
struct resource *regs = NULL;
struct resource *map = NULL;
+ struct fb_modelist *modelist;
int ret;
dev_dbg(dev, "%s BEGIN\n", __func__);
@@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
}
sinfo = info->par;
+ sinfo->pdev = pdev;
+ sinfo->info = info;
+
+ INIT_LIST_HEAD(&info->modelist);
- if (dev->platform_data) {
- pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
+ if (pdev->dev.of_node) {
+ ret = atmel_lcdfb_of_init(sinfo);
+ if (ret)
+ goto free_info;
+ } else if (dev->platform_data) {
+ struct fb_monspecs *monspecs;
+ int i;
+
+ pdata = dev->platform_data;
+ monspecs = pdata->default_monspecs;
sinfo->pdata = *pdata;
+
+ for (i = 0; i < monspecs->modedb_len; i++)
+ fb_add_videomode(&monspecs->modedb[i], &info->modelist);
+
+ sinfo->config = atmel_lcdfb_get_config(pdev);
+
+ info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
+ memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
}
- sinfo->info = info;
- sinfo->pdev = pdev;
- sinfo->config = atmel_lcdfb_get_config(pdev);
+
if (!sinfo->config)
goto free_info;
@@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
info->pseudo_palette = sinfo->pseudo_palette;
info->fbops = &atmel_lcdfb_ops;
- memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
info->fix = atmel_lcdfb_fix;
/* Enable LCDC Clocks */
@@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
}
atmel_lcdfb_start_clock(sinfo);
- ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
- info->monspecs.modedb_len, info->monspecs.modedb,
- pdata->default_bpp);
- if (!ret) {
- dev_err(dev, "no suitable video mode found\n");
- goto stop_clk;
- }
+ modelist = list_first_entry(&info->modelist,
+ struct fb_modelist, list);
+ fb_videomode_to_var(&info->var, &modelist->mode);
+ atmel_lcdfb_check_var(&info->var, info);
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs) {
@@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
goto unregister_irqs;
}
- /*
- * This makes sure that our colour bitfield
- * descriptors are correctly initialised.
- */
- atmel_lcdfb_check_var(&info->var, info);
-
- ret = fb_set_var(info, &info->var);
- if (ret) {
- dev_warn(dev, "unable to set display parameters\n");
- goto free_cmap;
- }
-
dev_set_drvdata(dev, info);
/*
@@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
goto reset_drvdata;
}
- /* add selected videomode to modelist */
- fb_var_to_videomode(&fbmode, &info->var);
- fb_add_videomode(&fbmode, &info->modelist);
-
/* Power up the LCDC screen */
atmel_lcdfb_power_control(sinfo, 1);
@@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
reset_drvdata:
dev_set_drvdata(dev, NULL);
-free_cmap:
fb_dealloc_cmap(&info->cmap);
unregister_irqs:
cancel_work_sync(&sinfo->task);
@@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
.driver = {
.name = "atmel_lcdfb",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
},
};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
get display timings from device tree
Use videomode helpers to get display timings and configurations from
device tree
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
.../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
drivers/video/Kconfig | 2 +
drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
3 files changed, 289 insertions(+), 32 deletions(-)
create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
new file mode 100644
index 0000000..1ec175e
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
@@ -0,0 +1,75 @@
+Atmel LCDC Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible :
+ "atmel,at91sam9261-lcdc" ,
+ "atmel,at91sam9263-lcdc" ,
+ "atmel,at91sam9g10-lcdc" ,
+ "atmel,at91sam9g45-lcdc" ,
+ "atmel,at91sam9g45es-lcdc" ,
+ "atmel,at91sam9rl-lcdc" ,
+ "atmel,at32ap-lcdc"
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : framebuffer controller interrupt
+- display: a phandle pointing to the display node
+
+Required nodes:
+- display: a display node is required to initialize the lcd panel
+ This should be in the board dts.
+- default-mode: a videomode within the display with timing parameters
+ as specified below.
+
+Example:
+
+ fb0: fb@0x00500000 {
+ compatible = "atmel,at91sam9g45-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ display = <&display0>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ };
+
+Atmel LCDC Display
+-----------------------------------------------------
+Required properties (as per of_videomode_helper):
+
+ - atmel,dmacon: dma controler configuration
+ - atmel,lcdcon2: lcd controler configuration
+ - atmel,guard-time: lcd guard time (Delay in frame periods)
+ - bits-per-pixel: lcd panel bit-depth.
+
+Optional properties (as per of_videomode_helper):
+ - atmel,lcdcon-backlight: enable backlight
+ - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
+ - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
+
+Example:
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 4c1546f..0687482 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1018,6 +1018,8 @@ config FB_ATMEL
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_VIDEOMODE
help
This enables support for the AT91/AT32 LCD Controller.
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index f67e226..4a31570 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -20,7 +20,11 @@
#include <linux/gfp.h>
#include <linux/module.h>
#include <linux/platform_data/atmel.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <video/of_display_timing.h>
+#include <video/videomode.h>
#include <mach/cpu.h>
#include <asm/gpio.h>
@@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
struct atmel_lcdfb_config *config;
};
+struct atmel_lcdfb_power_ctrl_gpio {
+ int gpio;
+ int active_low;
+
+ struct list_head list;
+};
+
#define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
#define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
@@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
clk_disable(sinfo->lcdc_clk);
}
+#ifdef CONFIG_OF
+static const struct of_device_id atmel_lcdfb_dt_ids[] = {
+ { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
+ { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
+ { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
+ { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
+ { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
+ { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
+ { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
+
+static const char *atmel_lcdfb_wiring_modes[] = {
+ [ATMEL_LCDC_WIRING_BGR] = "BRG",
+ [ATMEL_LCDC_WIRING_RGB] = "RGB",
+};
+
+const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
+{
+ const char *mode;
+ int err, i;
+
+ err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
+ if (err < 0)
+ return ATMEL_LCDC_WIRING_BGR;
+
+ for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
+ if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
+ return i;
+
+ return -ENODEV;
+}
+
+static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
+{
+ struct atmel_lcdfb_power_ctrl_gpio *og;
+
+ list_for_each_entry(og, &pdata->pwr_gpios, list)
+ gpio_set_value(og->gpio, on);
+}
+
+static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
+{
+ struct fb_info *info = sinfo->info;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+ struct fb_var_screeninfo *var = &info->var;
+ struct device *dev = &sinfo->pdev->dev;
+ struct device_node *np Þv->of_node;
+ struct device_node *display_np;
+ struct device_node *timings_np;
+ struct display_timings *timings;
+ enum of_gpio_flags flags;
+ struct atmel_lcdfb_power_ctrl_gpio *og;
+ bool is_gpio_power = false;
+ int ret = -ENOENT;
+ int i, gpio;
+
+ sinfo->config = (struct atmel_lcdfb_config*)
+ of_match_device(atmel_lcdfb_dt_ids, dev)->data;
+
+ display_np = of_parse_phandle(np, "display", 0);
+ if (!display_np) {
+ dev_err(dev, "failed to find display phandle\n");
+ return -ENOENT;
+ }
+
+ ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property atmel,guard-time\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property atmel,lcdcon2\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ ret = -ENOMEM;
+ for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
+ gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
+ i, &flags);
+ if (gpio < 0)
+ continue;
+
+ og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
+ if (!og)
+ goto put_display_node;
+
+ og->gpio = gpio;
+ og->active_low = flags & OF_GPIO_ACTIVE_LOW;
+ is_gpio_power = true;
+ ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
+ if (ret) {
+ dev_err(dev, "request gpio %d failed\n", gpio);
+ goto put_display_node;
+ }
+
+ ret = gpio_direction_output(gpio, og->active_low);
+ if (ret) {
+ dev_err(dev, "set direction output gpio %d failed\n", gpio);
+ goto put_display_node;
+ }
+ }
+
+ if (is_gpio_power)
+ pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
+
+ ret = atmel_lcdfb_get_of_wiring_modes(display_np);
+ if (ret < 0) {
+ dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
+ goto put_display_node;
+ }
+ pdata->lcd_wiring_mode = ret;
+
+ pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
+
+ timings = of_get_display_timings(display_np);
+ if (!timings) {
+ dev_err(dev, "failed to get display timings\n");
+ goto put_display_node;
+ }
+
+ timings_np = of_find_node_by_name(display_np, "display-timings");
+ if (!timings_np) {
+ dev_err(dev, "failed to find display-timings node\n");
+ goto put_display_node;
+ }
+
+ for (i = 0; i < of_get_child_count(timings_np); i++) {
+ struct videomode vm;
+ struct fb_videomode fb_vm;
+
+ ret = videomode_from_timing(timings, &vm, i);
+ if (ret < 0)
+ goto put_timings_node;
+ ret = fb_videomode_from_videomode(&vm, &fb_vm);
+ if (ret < 0)
+ goto put_timings_node;
+
+ fb_add_videomode(&fb_vm, &info->modelist);
+ }
+
+ return 0;
+
+put_timings_node:
+ of_node_put(timings_np);
+put_display_node:
+ of_node_put(display_np);
+ return ret;
+}
+#else
+static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
+{
+ return 0;
+}
+#endif
static int __init atmel_lcdfb_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct fb_info *info;
struct atmel_lcdfb_info *sinfo;
- struct atmel_lcdfb_pdata *pdata;
- struct fb_videomode fbmode;
+ struct atmel_lcdfb_pdata *pdata = NULL;
struct resource *regs = NULL;
struct resource *map = NULL;
+ struct fb_modelist *modelist;
int ret;
dev_dbg(dev, "%s BEGIN\n", __func__);
@@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
}
sinfo = info->par;
+ sinfo->pdev = pdev;
+ sinfo->info = info;
+
+ INIT_LIST_HEAD(&info->modelist);
- if (dev->platform_data) {
- pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
+ if (pdev->dev.of_node) {
+ ret = atmel_lcdfb_of_init(sinfo);
+ if (ret)
+ goto free_info;
+ } else if (dev->platform_data) {
+ struct fb_monspecs *monspecs;
+ int i;
+
+ pdata = dev->platform_data;
+ monspecs = pdata->default_monspecs;
sinfo->pdata = *pdata;
+
+ for (i = 0; i < monspecs->modedb_len; i++)
+ fb_add_videomode(&monspecs->modedb[i], &info->modelist);
+
+ sinfo->config = atmel_lcdfb_get_config(pdev);
+
+ info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
+ memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
}
- sinfo->info = info;
- sinfo->pdev = pdev;
- sinfo->config = atmel_lcdfb_get_config(pdev);
+
if (!sinfo->config)
goto free_info;
@@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
info->pseudo_palette = sinfo->pseudo_palette;
info->fbops = &atmel_lcdfb_ops;
- memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
info->fix = atmel_lcdfb_fix;
/* Enable LCDC Clocks */
@@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
}
atmel_lcdfb_start_clock(sinfo);
- ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
- info->monspecs.modedb_len, info->monspecs.modedb,
- pdata->default_bpp);
- if (!ret) {
- dev_err(dev, "no suitable video mode found\n");
- goto stop_clk;
- }
+ modelist = list_first_entry(&info->modelist,
+ struct fb_modelist, list);
+ fb_videomode_to_var(&info->var, &modelist->mode);
+ atmel_lcdfb_check_var(&info->var, info);
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs) {
@@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
goto unregister_irqs;
}
- /*
- * This makes sure that our colour bitfield
- * descriptors are correctly initialised.
- */
- atmel_lcdfb_check_var(&info->var, info);
-
- ret = fb_set_var(info, &info->var);
- if (ret) {
- dev_warn(dev, "unable to set display parameters\n");
- goto free_cmap;
- }
-
dev_set_drvdata(dev, info);
/*
@@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
goto reset_drvdata;
}
- /* add selected videomode to modelist */
- fb_var_to_videomode(&fbmode, &info->var);
- fb_add_videomode(&fbmode, &info->modelist);
-
/* Power up the LCDC screen */
atmel_lcdfb_power_control(sinfo, 1);
@@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
reset_drvdata:
dev_set_drvdata(dev, NULL);
-free_cmap:
fb_dealloc_cmap(&info->cmap);
unregister_irqs:
cancel_work_sync(&sinfo->task);
@@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
.driver = {
.name = "atmel_lcdfb",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
},
};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
get display timings from device tree
Use videomode helpers to get display timings and configurations from
device tree
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: linux-fbdev at vger.kernel.org
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
---
.../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
drivers/video/Kconfig | 2 +
drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
3 files changed, 289 insertions(+), 32 deletions(-)
create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
new file mode 100644
index 0000000..1ec175e
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
@@ -0,0 +1,75 @@
+Atmel LCDC Framebuffer
+-----------------------------------------------------
+
+Required properties:
+- compatible :
+ "atmel,at91sam9261-lcdc" ,
+ "atmel,at91sam9263-lcdc" ,
+ "atmel,at91sam9g10-lcdc" ,
+ "atmel,at91sam9g45-lcdc" ,
+ "atmel,at91sam9g45es-lcdc" ,
+ "atmel,at91sam9rl-lcdc" ,
+ "atmel,at32ap-lcdc"
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : framebuffer controller interrupt
+- display: a phandle pointing to the display node
+
+Required nodes:
+- display: a display node is required to initialize the lcd panel
+ This should be in the board dts.
+- default-mode: a videomode within the display with timing parameters
+ as specified below.
+
+Example:
+
+ fb0: fb at 0x00500000 {
+ compatible = "atmel,at91sam9g45-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ display = <&display0>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ };
+
+Atmel LCDC Display
+-----------------------------------------------------
+Required properties (as per of_videomode_helper):
+
+ - atmel,dmacon: dma controler configuration
+ - atmel,lcdcon2: lcd controler configuration
+ - atmel,guard-time: lcd guard time (Delay in frame periods)
+ - bits-per-pixel: lcd panel bit-depth.
+
+Optional properties (as per of_videomode_helper):
+ - atmel,lcdcon-backlight: enable backlight
+ - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
+ - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
+
+Example:
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 4c1546f..0687482 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1018,6 +1018,8 @@ config FB_ATMEL
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_VIDEOMODE
help
This enables support for the AT91/AT32 LCD Controller.
diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
index f67e226..4a31570 100644
--- a/drivers/video/atmel_lcdfb.c
+++ b/drivers/video/atmel_lcdfb.c
@@ -20,7 +20,11 @@
#include <linux/gfp.h>
#include <linux/module.h>
#include <linux/platform_data/atmel.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <video/of_display_timing.h>
+#include <video/videomode.h>
#include <mach/cpu.h>
#include <asm/gpio.h>
@@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
struct atmel_lcdfb_config *config;
};
+struct atmel_lcdfb_power_ctrl_gpio {
+ int gpio;
+ int active_low;
+
+ struct list_head list;
+};
+
#define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
#define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
@@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
clk_disable(sinfo->lcdc_clk);
}
+#ifdef CONFIG_OF
+static const struct of_device_id atmel_lcdfb_dt_ids[] = {
+ { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
+ { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
+ { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
+ { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
+ { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
+ { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
+ { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
+
+static const char *atmel_lcdfb_wiring_modes[] = {
+ [ATMEL_LCDC_WIRING_BGR] = "BRG",
+ [ATMEL_LCDC_WIRING_RGB] = "RGB",
+};
+
+const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
+{
+ const char *mode;
+ int err, i;
+
+ err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
+ if (err < 0)
+ return ATMEL_LCDC_WIRING_BGR;
+
+ for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
+ if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
+ return i;
+
+ return -ENODEV;
+}
+
+static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
+{
+ struct atmel_lcdfb_power_ctrl_gpio *og;
+
+ list_for_each_entry(og, &pdata->pwr_gpios, list)
+ gpio_set_value(og->gpio, on);
+}
+
+static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
+{
+ struct fb_info *info = sinfo->info;
+ struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
+ struct fb_var_screeninfo *var = &info->var;
+ struct device *dev = &sinfo->pdev->dev;
+ struct device_node *np =dev->of_node;
+ struct device_node *display_np;
+ struct device_node *timings_np;
+ struct display_timings *timings;
+ enum of_gpio_flags flags;
+ struct atmel_lcdfb_power_ctrl_gpio *og;
+ bool is_gpio_power = false;
+ int ret = -ENOENT;
+ int i, gpio;
+
+ sinfo->config = (struct atmel_lcdfb_config*)
+ of_match_device(atmel_lcdfb_dt_ids, dev)->data;
+
+ display_np = of_parse_phandle(np, "display", 0);
+ if (!display_np) {
+ dev_err(dev, "failed to find display phandle\n");
+ return -ENOENT;
+ }
+
+ ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property atmel,guard-time\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property atmel,lcdcon2\n");
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ ret = -ENOMEM;
+ for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
+ gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
+ i, &flags);
+ if (gpio < 0)
+ continue;
+
+ og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
+ if (!og)
+ goto put_display_node;
+
+ og->gpio = gpio;
+ og->active_low = flags & OF_GPIO_ACTIVE_LOW;
+ is_gpio_power = true;
+ ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
+ if (ret) {
+ dev_err(dev, "request gpio %d failed\n", gpio);
+ goto put_display_node;
+ }
+
+ ret = gpio_direction_output(gpio, og->active_low);
+ if (ret) {
+ dev_err(dev, "set direction output gpio %d failed\n", gpio);
+ goto put_display_node;
+ }
+ }
+
+ if (is_gpio_power)
+ pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
+
+ ret = atmel_lcdfb_get_of_wiring_modes(display_np);
+ if (ret < 0) {
+ dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
+ goto put_display_node;
+ }
+ pdata->lcd_wiring_mode = ret;
+
+ pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
+
+ timings = of_get_display_timings(display_np);
+ if (!timings) {
+ dev_err(dev, "failed to get display timings\n");
+ goto put_display_node;
+ }
+
+ timings_np = of_find_node_by_name(display_np, "display-timings");
+ if (!timings_np) {
+ dev_err(dev, "failed to find display-timings node\n");
+ goto put_display_node;
+ }
+
+ for (i = 0; i < of_get_child_count(timings_np); i++) {
+ struct videomode vm;
+ struct fb_videomode fb_vm;
+
+ ret = videomode_from_timing(timings, &vm, i);
+ if (ret < 0)
+ goto put_timings_node;
+ ret = fb_videomode_from_videomode(&vm, &fb_vm);
+ if (ret < 0)
+ goto put_timings_node;
+
+ fb_add_videomode(&fb_vm, &info->modelist);
+ }
+
+ return 0;
+
+put_timings_node:
+ of_node_put(timings_np);
+put_display_node:
+ of_node_put(display_np);
+ return ret;
+}
+#else
+static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
+{
+ return 0;
+}
+#endif
static int __init atmel_lcdfb_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct fb_info *info;
struct atmel_lcdfb_info *sinfo;
- struct atmel_lcdfb_pdata *pdata;
- struct fb_videomode fbmode;
+ struct atmel_lcdfb_pdata *pdata = NULL;
struct resource *regs = NULL;
struct resource *map = NULL;
+ struct fb_modelist *modelist;
int ret;
dev_dbg(dev, "%s BEGIN\n", __func__);
@@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
}
sinfo = info->par;
+ sinfo->pdev = pdev;
+ sinfo->info = info;
+
+ INIT_LIST_HEAD(&info->modelist);
- if (dev->platform_data) {
- pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
+ if (pdev->dev.of_node) {
+ ret = atmel_lcdfb_of_init(sinfo);
+ if (ret)
+ goto free_info;
+ } else if (dev->platform_data) {
+ struct fb_monspecs *monspecs;
+ int i;
+
+ pdata = dev->platform_data;
+ monspecs = pdata->default_monspecs;
sinfo->pdata = *pdata;
+
+ for (i = 0; i < monspecs->modedb_len; i++)
+ fb_add_videomode(&monspecs->modedb[i], &info->modelist);
+
+ sinfo->config = atmel_lcdfb_get_config(pdev);
+
+ info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
+ memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
} else {
dev_err(dev, "cannot get default configuration\n");
goto free_info;
}
- sinfo->info = info;
- sinfo->pdev = pdev;
- sinfo->config = atmel_lcdfb_get_config(pdev);
+
if (!sinfo->config)
goto free_info;
@@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
info->pseudo_palette = sinfo->pseudo_palette;
info->fbops = &atmel_lcdfb_ops;
- memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
info->fix = atmel_lcdfb_fix;
/* Enable LCDC Clocks */
@@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
}
atmel_lcdfb_start_clock(sinfo);
- ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
- info->monspecs.modedb_len, info->monspecs.modedb,
- pdata->default_bpp);
- if (!ret) {
- dev_err(dev, "no suitable video mode found\n");
- goto stop_clk;
- }
+ modelist = list_first_entry(&info->modelist,
+ struct fb_modelist, list);
+ fb_videomode_to_var(&info->var, &modelist->mode);
+ atmel_lcdfb_check_var(&info->var, info);
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs) {
@@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
goto unregister_irqs;
}
- /*
- * This makes sure that our colour bitfield
- * descriptors are correctly initialised.
- */
- atmel_lcdfb_check_var(&info->var, info);
-
- ret = fb_set_var(info, &info->var);
- if (ret) {
- dev_warn(dev, "unable to set display parameters\n");
- goto free_cmap;
- }
-
dev_set_drvdata(dev, info);
/*
@@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
goto reset_drvdata;
}
- /* add selected videomode to modelist */
- fb_var_to_videomode(&fbmode, &info->var);
- fb_add_videomode(&fbmode, &info->modelist);
-
/* Power up the LCDC screen */
atmel_lcdfb_power_control(sinfo, 1);
@@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
reset_drvdata:
dev_set_drvdata(dev, NULL);
-free_cmap:
fb_dealloc_cmap(&info->cmap);
unregister_irqs:
cancel_work_sync(&sinfo->task);
@@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
.driver = {
.name = "atmel_lcdfb",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
},
};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 5/8] ARM: at91: sam9g45: add lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss, Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 6b1d4ca..ab8a8fc 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -322,6 +322,42 @@
};
};
+ fb {
+ pinctrl_fb: fb-0 {
+ atmel,pins =
+ <4 0 0x1 0x0 /* PE0 periph A */
+ 4 2 0x1 0x0 /* PE2 periph A */
+ 4 3 0x1 0x0 /* PE3 periph A */
+ 4 4 0x1 0x0 /* PE4 periph A */
+ 4 5 0x1 0x0 /* PE5 periph A */
+ 4 6 0x1 0x0 /* PE6 periph A */
+ 4 7 0x1 0x0 /* PE7 periph A */
+ 4 8 0x1 0x0 /* PE8 periph A */
+ 4 9 0x1 0x0 /* PE9 periph A */
+ 4 10 0x1 0x0 /* PE10 periph A */
+ 4 11 0x1 0x0 /* PE11 periph A */
+ 4 12 0x1 0x0 /* PE12 periph A */
+ 4 13 0x1 0x0 /* PE13 periph A */
+ 4 14 0x1 0x0 /* PE14 periph A */
+ 4 15 0x1 0x0 /* PE15 periph A */
+ 4 16 0x1 0x0 /* PE16 periph A */
+ 4 17 0x1 0x0 /* PE17 periph A */
+ 4 18 0x1 0x0 /* PE18 periph A */
+ 4 19 0x1 0x0 /* PE19 periph A */
+ 4 20 0x1 0x0 /* PE20 periph A */
+ 4 21 0x1 0x0 /* PE21 periph A */
+ 4 22 0x1 0x0 /* PE22 periph A */
+ 4 23 0x1 0x0 /* PE23 periph A */
+ 4 24 0x1 0x0 /* PE24 periph A */
+ 4 25 0x1 0x0 /* PE25 periph A */
+ 4 26 0x1 0x0 /* PE26 periph A */
+ 4 27 0x1 0x0 /* PE27 periph A */
+ 4 28 0x1 0x0 /* PE28 periph A */
+ 4 29 0x1 0x0 /* PE29 periph A */
+ 4 30 0x1 0x0>; /* PE30 periph A */
+ };
+ };
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -533,6 +569,17 @@
};
};
+ fb0: fb@0x00500000 {
+ compatible = "atmel,at91sam9g45-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
nand0: nand@40000000 {
compatible = "atmel,at91rm9200-nand";
#address-cells = <1>;
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 5/8] ARM: at91: sam9g45: add lcd support
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 6b1d4ca..ab8a8fc 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -322,6 +322,42 @@
};
};
+ fb {
+ pinctrl_fb: fb-0 {
+ atmel,pins =
+ <4 0 0x1 0x0 /* PE0 periph A */
+ 4 2 0x1 0x0 /* PE2 periph A */
+ 4 3 0x1 0x0 /* PE3 periph A */
+ 4 4 0x1 0x0 /* PE4 periph A */
+ 4 5 0x1 0x0 /* PE5 periph A */
+ 4 6 0x1 0x0 /* PE6 periph A */
+ 4 7 0x1 0x0 /* PE7 periph A */
+ 4 8 0x1 0x0 /* PE8 periph A */
+ 4 9 0x1 0x0 /* PE9 periph A */
+ 4 10 0x1 0x0 /* PE10 periph A */
+ 4 11 0x1 0x0 /* PE11 periph A */
+ 4 12 0x1 0x0 /* PE12 periph A */
+ 4 13 0x1 0x0 /* PE13 periph A */
+ 4 14 0x1 0x0 /* PE14 periph A */
+ 4 15 0x1 0x0 /* PE15 periph A */
+ 4 16 0x1 0x0 /* PE16 periph A */
+ 4 17 0x1 0x0 /* PE17 periph A */
+ 4 18 0x1 0x0 /* PE18 periph A */
+ 4 19 0x1 0x0 /* PE19 periph A */
+ 4 20 0x1 0x0 /* PE20 periph A */
+ 4 21 0x1 0x0 /* PE21 periph A */
+ 4 22 0x1 0x0 /* PE22 periph A */
+ 4 23 0x1 0x0 /* PE23 periph A */
+ 4 24 0x1 0x0 /* PE24 periph A */
+ 4 25 0x1 0x0 /* PE25 periph A */
+ 4 26 0x1 0x0 /* PE26 periph A */
+ 4 27 0x1 0x0 /* PE27 periph A */
+ 4 28 0x1 0x0 /* PE28 periph A */
+ 4 29 0x1 0x0 /* PE29 periph A */
+ 4 30 0x1 0x0>; /* PE30 periph A */
+ };
+ };
+
pioA: gpio at fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -533,6 +569,17 @@
};
};
+ fb0: fb at 0x00500000 {
+ compatible = "atmel,at91sam9g45-lcdc";
+ reg = <0x00500000 0x1000>;
+ interrupts = <23 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
nand0: nand at 40000000 {
compatible = "atmel,at91rm9200-nand";
#address-cells = <1>;
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 6/8] ARM: at91: sam9263: add fb dt support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss, Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 271d4de..3d0effa 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -303,6 +303,34 @@
};
};
+ fb {
+ pinctrl_fb: fb-0 {
+ atmel,pins =
+ <2 1 0x1 0x0 /* PC1 periph A */
+ 2 2 0x1 0x0 /* PC2 periph A */
+ 2 3 0x1 0x0 /* PC3 periph A */
+ 1 9 0x2 0x0 /* PB9 periph B */
+ 2 6 0x1 0x0 /* PC6 periph A */
+ 2 7 0x1 0x0 /* PC7 periph A */
+ 2 8 0x1 0x0 /* PC8 periph A */
+ 2 9 0x1 0x0 /* PC9 periph A */
+ 2 10 0x1 0x0 /* PC10 periph A */
+ 2 11 0x1 0x0 /* PC11 periph A */
+ 2 14 0x1 0x0 /* PC14 periph A */
+ 2 15 0x1 0x0 /* PC15 periph A */
+ 2 16 0x1 0x0 /* PC16 periph A */
+ 2 12 0x2 0x0 /* PC12 periph B */
+ 2 18 0x1 0x0 /* PC18 periph A */
+ 2 19 0x1 0x0 /* PC19 periph A */
+ 2 22 0x1 0x0 /* PC22 periph A */
+ 2 23 0x1 0x0 /* PC23 periph A */
+ 2 24 0x1 0x0 /* PC24 periph A */
+ 2 17 0x2 0x0 /* PC17 periph B */
+ 2 26 0x1 0x0 /* PC26 periph A */
+ 2 27 0x1 0x0>; /* PC27 periph A */
+ };
+ };
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -464,6 +492,17 @@
};
};
+ fb0: fb@0x00500000 {
+ compatible = "atmel,at91sam9263-lcdc";
+ reg = <0x00700000 0x1000>;
+ interrupts = <26 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
nand0: nand@40000000 {
compatible = "atmel,at91rm9200-nand";
#address-cells = <1>;
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 6/8] ARM: at91: sam9263: add fb dt support
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 271d4de..3d0effa 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -303,6 +303,34 @@
};
};
+ fb {
+ pinctrl_fb: fb-0 {
+ atmel,pins =
+ <2 1 0x1 0x0 /* PC1 periph A */
+ 2 2 0x1 0x0 /* PC2 periph A */
+ 2 3 0x1 0x0 /* PC3 periph A */
+ 1 9 0x2 0x0 /* PB9 periph B */
+ 2 6 0x1 0x0 /* PC6 periph A */
+ 2 7 0x1 0x0 /* PC7 periph A */
+ 2 8 0x1 0x0 /* PC8 periph A */
+ 2 9 0x1 0x0 /* PC9 periph A */
+ 2 10 0x1 0x0 /* PC10 periph A */
+ 2 11 0x1 0x0 /* PC11 periph A */
+ 2 14 0x1 0x0 /* PC14 periph A */
+ 2 15 0x1 0x0 /* PC15 periph A */
+ 2 16 0x1 0x0 /* PC16 periph A */
+ 2 12 0x2 0x0 /* PC12 periph B */
+ 2 18 0x1 0x0 /* PC18 periph A */
+ 2 19 0x1 0x0 /* PC19 periph A */
+ 2 22 0x1 0x0 /* PC22 periph A */
+ 2 23 0x1 0x0 /* PC23 periph A */
+ 2 24 0x1 0x0 /* PC24 periph A */
+ 2 17 0x2 0x0 /* PC17 periph B */
+ 2 26 0x1 0x0 /* PC26 periph A */
+ 2 27 0x1 0x0>; /* PC27 periph A */
+ };
+ };
+
pioA: gpio at fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -464,6 +492,17 @@
};
};
+ fb0: fb at 0x00500000 {
+ compatible = "atmel,at91sam9263-lcdc";
+ reg = <0x00700000 0x1000>;
+ interrupts = <26 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fb>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
nand0: nand at 40000000 {
compatible = "atmel,at91rm9200-nand";
#address-cells = <1>;
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 7/8] ARM: at91: at9sam9m10g45ek: add dt lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss, Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9m10g45ek.dts | 29 +++++++++++++++++++++++++++++
1 file changed, 29 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 20c3191..79dc034 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -104,6 +104,35 @@
};
};
+ fb0: fb@0x00500000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = "RGB";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
+ };
+
nand0: nand@40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 7/8] ARM: at91: at9sam9m10g45ek: add dt lcd support
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9m10g45ek.dts | 29 +++++++++++++++++++++++++++++
1 file changed, 29 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 20c3191..79dc034 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -104,6 +104,35 @@
};
};
+ fb0: fb at 0x00500000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <32>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <9>;
+ atmel,lcd-wiring-mode = "RGB";
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <1>;
+ hfront-porch = <1>;
+ vback-porch = <40>;
+ vfront-porch = <1>;
+ hsync-len = <45>;
+ vsync-len = <1>;
+ };
+ };
+ };
+ };
+
nand0: nand at 40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 8/8] ARM: at91: sam9263ek: add dt lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss, Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9263ek.dts | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 1eb0872..d471b49 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -81,6 +81,36 @@
};
};
+ fb0: fb@0x00500000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <4965000>;
+ hactive = <240>;
+ vactive = <320>;
+ hback-porch = <1>;
+ hfront-porch = <33>;
+ vback-porch = <1>;
+ vfront-porch = <0>;
+ hsync-len = <5>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+ };
+
nand0: nand@40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* [PATCH 8/8] ARM: at91: sam9263ek: add dt lcd support
@ 2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-11 15:00 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/at91sam9263ek.dts | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 1eb0872..d471b49 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -81,6 +81,36 @@
};
};
+ fb0: fb at 0x00500000 {
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ atmel,lcdcon-backlight;
+ atmel,dmacon = <0x1>;
+ atmel,lcdcon2 = <0x80008002>;
+ atmel,guard-time = <1>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <4965000>;
+ hactive = <240>;
+ vactive = <320>;
+ hback-porch = <1>;
+ hfront-porch = <33>;
+ vback-porch = <1>;
+ vfront-porch = <0>;
+ hsync-len = <5>;
+ vsync-len = <1>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+ };
+
nand0: nand at 40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
--
1.7.10.4
^ permalink raw reply related [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-12 9:52 ` Hans-Christian Egtvedt
-1 siblings, 0 replies; 91+ messages in thread
From: Hans-Christian Egtvedt @ 2013-04-12 9:52 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Andrew Morton, devicetree-discuss, Nicolas Ferre, linux-fbdev,
linux-arm-kernel
Around Thu 11 Apr 2013 17:00:15 +0200 or thereabout, Jean-Christophe PLAGNIOL-VILLARD wrote:
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
For the AVR32 bits
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
<snipp diff>
--
HcE
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-04-12 9:52 ` Hans-Christian Egtvedt
0 siblings, 0 replies; 91+ messages in thread
From: Hans-Christian Egtvedt @ 2013-04-12 9:52 UTC (permalink / raw)
To: linux-arm-kernel
Around Thu 11 Apr 2013 17:00:15 +0200 or thereabout, Jean-Christophe PLAGNIOL-VILLARD wrote:
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
For the AVR32 bits
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
<snipp diff>
--
HcE
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-04-12 9:52 ` Hans-Christian Egtvedt
0 siblings, 0 replies; 91+ messages in thread
From: Hans-Christian Egtvedt @ 2013-04-12 9:52 UTC (permalink / raw)
To: linux-arm-kernel
Around Thu 11 Apr 2013 17:00:15 +0200 or thereabout, Jean-Christophe PLAGNIOL-VILLARD wrote:
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
For the AVR32 bits
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
<snipp diff>
--
HcE
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-16 12:33 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:33 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Andrew Morton, devicetree-discuss, linux-fbdev, linux-arm-kernel,
Hans-Christian Egtvedt
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
>
> diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
> index 629ea5f..b2a3474 100644
> --- a/arch/arm/mach-at91/at91sam9261_devices.c
> +++ b/arch/arm/mach-at91/at91sam9261_devices.c
> @@ -465,7 +465,7 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -498,7 +498,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data) {
> return;
> @@ -559,7 +559,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
> index 858c8aa..4aeaddd 100644
> --- a/arch/arm/mach-at91/at91sam9263_devices.c
> +++ b/arch/arm/mach-at91/at91sam9263_devices.c
> @@ -832,7 +832,7 @@ void __init at91_add_device_can(struct at91_can_data *data) {}
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -859,7 +859,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data)
> return;
> @@ -891,7 +891,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
> index fe626d4..82636c7 100644
> --- a/arch/arm/mach-at91/at91sam9g45_devices.c
> +++ b/arch/arm/mach-at91/at91sam9g45_devices.c
> @@ -965,7 +965,7 @@ void __init at91_add_device_isi(struct isi_platform_data *data,
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -991,7 +991,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data)
> return;
> @@ -1037,7 +1037,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
> index 352468f..a698bda 100644
> --- a/arch/arm/mach-at91/at91sam9rl_devices.c
> +++ b/arch/arm/mach-at91/at91sam9rl_devices.c
> @@ -498,7 +498,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -525,7 +525,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data) {
> return;
> @@ -557,7 +557,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
> index b446645..c819e29 100644
> --- a/arch/arm/mach-at91/board-sam9261ek.c
> +++ b/arch/arm/mach-at91/board-sam9261ek.c
> @@ -405,7 +405,7 @@ static void at91_lcdc_stn_power_control(int on)
> }
> }
>
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .default_bpp = 1,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> .default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
> @@ -460,7 +460,7 @@ static void at91_lcdc_tft_power_control(int on)
> at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
> }
>
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -475,7 +475,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> #endif
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
> index 3284df0..0fdae3f 100644
> --- a/arch/arm/mach-at91/board-sam9263ek.c
> +++ b/arch/arm/mach-at91/board-sam9263ek.c
> @@ -281,7 +281,7 @@ static void at91_lcdc_power_control(int on)
> }
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -292,7 +292,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
> index 2a94896..ef39078 100644
> --- a/arch/arm/mach-at91/board-sam9m10g45ek.c
> +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
> @@ -284,7 +284,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 32,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -295,7 +295,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
> index aa265dc..b77d7a9 100644
> --- a/arch/arm/mach-at91/board-sam9rlek.c
> +++ b/arch/arm/mach-at91/board-sam9rlek.c
> @@ -179,7 +179,7 @@ static void at91_lcdc_power_control(int on)
> }
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -191,7 +191,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h
> index 4a234fb..6c08b34 100644
> --- a/arch/arm/mach-at91/board.h
> +++ b/arch/arm/mach-at91/board.h
> @@ -107,8 +107,8 @@ extern void __init at91_add_device_pwm(u32 mask);
> extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
>
> /* LCD Controller */
> -struct atmel_lcdfb_info;
> -extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
> +struct atmel_lcdfb_pdata;
> +extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
>
> /* AC97 */
> extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
> diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
> index 2038875..dc42804 100644
> --- a/arch/avr32/boards/atngw100/evklcd10x.c
> +++ b/arch/avr32/boards/atngw100/evklcd10x.c
> @@ -58,7 +58,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 28330000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -96,7 +96,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 7000000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -134,7 +134,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 6400000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c
> index f914319..ccc9599 100644
> --- a/arch/avr32/boards/atngw100/mrmt.c
> +++ b/arch/avr32/boards/atngw100/mrmt.c
> @@ -83,7 +83,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
> .dclkmax = 9260000,
> };
>
> -static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -126,7 +126,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
> .dclkmax = 9260000,
> };
>
> -static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
> index 9392d32..653cc09 100644
> --- a/arch/avr32/boards/atstk1000/atstk1000.h
> +++ b/arch/avr32/boards/atstk1000/atstk1000.h
> @@ -10,7 +10,7 @@
> #ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
> #define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
>
> -extern struct atmel_lcdfb_info atstk1000_lcdc_data;
> +extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
>
> void atstk1000_setup_j2_leds(void);
>
> diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
> index 2d6b560..b6b88f5 100644
> --- a/arch/avr32/boards/atstk1000/setup.c
> +++ b/arch/avr32/boards/atstk1000/setup.c
> @@ -55,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = {
> .dclkmax = 30000000,
> };
>
> -struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
> index 27bd6fb..7b1f2cd 100644
> --- a/arch/avr32/boards/favr-32/setup.c
> +++ b/arch/avr32/boards/favr-32/setup.c
> @@ -125,7 +125,7 @@ static struct fb_monspecs __initdata favr32_default_monspecs = {
> .dclkmax = 28000000,
> };
>
> -struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata favr32_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
> index 9d1efd1..dc0e317 100644
> --- a/arch/avr32/boards/hammerhead/setup.c
> +++ b/arch/avr32/boards/hammerhead/setup.c
> @@ -77,7 +77,7 @@ static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
> .dclkmax = 10000000,
> };
>
> -struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata hammerhead_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
> index 85a543c..e7683ee 100644
> --- a/arch/avr32/boards/merisc/display.c
> +++ b/arch/avr32/boards/merisc/display.c
> @@ -45,7 +45,7 @@ static struct fb_monspecs merisc_fb_monspecs = {
> .dclkmax = 30000000,
> };
>
> -struct atmel_lcdfb_info merisc_lcdc_data = {
> +struct atmel_lcdfb_pdata merisc_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
> index 05358aa..1cb8e9c 100644
> --- a/arch/avr32/boards/mimc200/setup.c
> +++ b/arch/avr32/boards/mimc200/setup.c
> @@ -8,7 +8,7 @@
> * published by the Free Software Foundation.
> */
>
> -extern struct atmel_lcdfb_info mimc200_lcdc_data;
> +extern struct atmel_lcdfb_pdata mimc200_lcdc_data;
>
> #include <linux/clk.h>
> #include <linux/etherdevice.h>
> @@ -71,7 +71,7 @@ static struct fb_monspecs __initdata mimc200_default_monspecs = {
> .dclkmax = 25200000,
> };
>
> -struct atmel_lcdfb_info __initdata mimc200_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata mimc200_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
> index 7c2f668..0badb05 100644
> --- a/arch/avr32/mach-at32ap/at32ap700x.c
> +++ b/arch/avr32/mach-at32ap/at32ap700x.c
> @@ -1437,7 +1437,7 @@ fail:
> * LCDC
> * -------------------------------------------------------------------- */
> #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
> -static struct atmel_lcdfb_info atmel_lcdfb0_data;
> +static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
> static struct resource atmel_lcdfb0_resource[] = {
> {
> .start = 0xff000000,
> @@ -1465,12 +1465,12 @@ static struct clk atmel_lcdfb0_pixclk = {
> };
>
> struct platform_device *__init
> -at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> +at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
> unsigned long fbmem_start, unsigned long fbmem_len,
> u64 pin_mask)
> {
> struct platform_device *pdev;
> - struct atmel_lcdfb_info *info;
> + struct atmel_lcdfb_pdata *info;
> struct fb_monspecs *monspecs;
> struct fb_videomode *modedb;
> unsigned int modedb_size;
> @@ -1527,7 +1527,7 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> }
>
> info = pdev->dev.platform_data;
> - memcpy(info, data, sizeof(struct atmel_lcdfb_info));
> + memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
> info->default_monspecs = monspecs;
>
> pdev->name = "at32ap-lcdfb";
> diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h
> index d485b03..f1a316d 100644
> --- a/arch/avr32/mach-at32ap/include/mach/board.h
> +++ b/arch/avr32/mach-at32ap/include/mach/board.h
> @@ -44,9 +44,9 @@ struct platform_device *
> at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
> void at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n);
>
> -struct atmel_lcdfb_info;
> +struct atmel_lcdfb_pdata;
> struct platform_device *
> -at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> +at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
> unsigned long fbmem_start, unsigned long fbmem_len,
> u64 pin_mask);
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index c1a2914..98733cd4 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,12 +20,45 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <video/of_display_timing.h>
I am not sure this one is useful for this patch, maybe place it in the
4/8 one.
> #include <mach/cpu.h>
> #include <asm/gpio.h>
>
> #include <video/atmel_lcdc.h>
>
> +struct atmel_lcdfb_config {
> + bool have_alt_pixclock;
> + bool have_hozval;
> + bool have_intensity_bit;
> +};
> +
> + /* LCD Controller info data structure, stored in device platform_data */
Is comment still relevant?
> +struct atmel_lcdfb_info {
> + spinlock_t lock;
> + struct fb_info *info;
> + void __iomem *mmio;
> + int irq_base;
> + struct work_struct task;
> +
> + unsigned int smem_len;
> + struct platform_device *pdev;
> + struct clk *bus_clk;
> + struct clk *lcdc_clk;
> +
> + struct backlight_device *backlight;
> + u8 bl_power;
> + bool lcdcon_pol_negative;
> + u8 saved_lcdcon;
> +
> + u32 pseudo_palette[16];
> + bool have_intensity_bit;
> +
> + struct atmel_lcdfb_pdata pdata;
> +
> + struct atmel_lcdfb_config *config;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -34,12 +67,6 @@
> #define ATMEL_LCDC_DMA_BURST_LEN 8 /* words */
> #define ATMEL_LCDC_FIFO_SIZE 512 /* words */
>
> -struct atmel_lcdfb_config {
> - bool have_alt_pixclock;
> - bool have_hozval;
> - bool have_intensity_bit;
> -};
> -
> static struct atmel_lcdfb_config at91sam9261_config = {
> .have_hozval = true,
> .have_intensity_bit = true,
> @@ -242,6 +269,8 @@ static void exit_backlight(struct atmel_lcdfb_info *sinfo)
>
> static void init_contrast(struct atmel_lcdfb_info *sinfo)
> {
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> /* contrast pwm can be 'inverted' */
> if (sinfo->lcdcon_pol_negative)
> contrast_ctr &= ~(ATMEL_LCDC_POL_POSITIVE);
> @@ -250,7 +279,7 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
>
> - if (sinfo->lcdcon_is_backlight)
> + if (pdata->lcdcon_is_backlight)
> init_backlight(sinfo);
> }
>
> @@ -293,9 +322,11 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
>
> static void atmel_lcdfb_stop_nowait(struct atmel_lcdfb_info *sinfo)
> {
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> /* Turn off the LCD controller and the DMA controller */
> lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
> - sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
> + pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
>
> /* Wait for the LCDC core to become idle */
> while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
> @@ -315,9 +346,11 @@ static void atmel_lcdfb_stop(struct atmel_lcdfb_info *sinfo)
>
> static void atmel_lcdfb_start(struct atmel_lcdfb_info *sinfo)
> {
> - lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> + lcdc_writel(sinfo, ATMEL_LCDC_DMACON, pdata->default_dmacon);
> lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
> - (sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
> + (pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
> | ATMEL_LCDC_PWR);
> }
>
> @@ -418,6 +451,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> {
> struct device *dev = info->device;
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned long clk_value_khz;
>
> clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
> @@ -501,7 +535,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> else
> var->green.length = 6;
>
> - if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> /* RGB:5X5 mode */
> var->red.offset = var->green.length + 5;
> var->blue.offset = 0;
> @@ -518,7 +552,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> var->transp.length = 8;
> /* fall through */
> case 24:
> - if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> /* RGB:888 mode */
> var->red.offset = 16;
> var->blue.offset = 0;
> @@ -567,6 +601,7 @@ static void atmel_lcdfb_reset(struct atmel_lcdfb_info *sinfo)
> static int atmel_lcdfb_set_par(struct fb_info *info)
> {
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned long hozval_linesz;
> unsigned long value;
> unsigned long clk_value_khz;
> @@ -628,7 +663,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
>
>
> /* Initialize control register 2 */
> - value = sinfo->default_lcdcon2;
> + value = pdata->default_lcdcon2;
>
> if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
> value |= ATMEL_LCDC_INVLINE_INVERTED;
> @@ -732,6 +767,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
> unsigned int transp, struct fb_info *info)
> {
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned int val;
> u32 *pal;
> int ret = 1;
> @@ -768,8 +804,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
> */
> } else {
> /* new style BGR:565 / RGB:565 */
> - if (sinfo->lcd_wiring_mode ==
> - ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> val = ((blue >> 11) & 0x001f);
> val |= ((red >> 0) & 0xf800);
> } else {
> @@ -909,7 +944,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct fb_info *info;
> struct atmel_lcdfb_info *sinfo;
> - struct atmel_lcdfb_info *pdata_sinfo;
> + struct atmel_lcdfb_pdata *pdata;
> struct fb_videomode fbmode;
> struct resource *regs = NULL;
> struct resource *map = NULL;
> @@ -927,17 +962,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> sinfo = info->par;
>
> if (dev->platform_data) {
> - pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
> - sinfo->default_bpp = pdata_sinfo->default_bpp;
> - sinfo->default_dmacon = pdata_sinfo->default_dmacon;
> - sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
> - sinfo->default_monspecs = pdata_sinfo->default_monspecs;
> - sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
> - sinfo->guard_time = pdata_sinfo->guard_time;
> - sinfo->smem_len = pdata_sinfo->smem_len;
> - sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
> - sinfo->lcdcon_pol_negative = pdata_sinfo->lcdcon_pol_negative;
> - sinfo->lcd_wiring_mode = pdata_sinfo->lcd_wiring_mode;
> + pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> + sinfo->pdata = *pdata;
> } else {
> dev_err(dev, "cannot get default configuration\n");
> goto free_info;
> @@ -953,7 +979,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> info->pseudo_palette = sinfo->pseudo_palette;
> info->fbops = &atmel_lcdfb_ops;
>
> - memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> info->fix = atmel_lcdfb_fix;
>
> /* Enable LCDC Clocks */
> @@ -971,7 +997,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>
> ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> info->monspecs.modedb_len, info->monspecs.modedb,
> - sinfo->default_bpp);
> + pdata->default_bpp);
> if (!ret) {
> dev_err(dev, "no suitable video mode found\n");
> goto stop_clk;
> @@ -1088,8 +1114,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> fb_add_videomode(&fbmode, &info->modelist);
>
> /* Power up the LCDC screen */
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(1);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(1);
>
> dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
> info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
> @@ -1134,15 +1160,17 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct fb_info *info = dev_get_drvdata(dev);
> struct atmel_lcdfb_info *sinfo;
> + struct atmel_lcdfb_pdata *pdata;
>
> if (!info || !info->par)
> return 0;
> sinfo = info->par;
> + pdata = &sinfo->pdata;
>
> cancel_work_sync(&sinfo->task);
> exit_backlight(sinfo);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(0);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(0);
> unregister_framebuffer(info);
> atmel_lcdfb_stop_clock(sinfo);
> clk_put(sinfo->lcdc_clk);
> @@ -1170,6 +1198,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> /*
> * We don't want to handle interrupts while the clock is
> @@ -1179,8 +1208,8 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
>
> sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(0);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(0);
>
> atmel_lcdfb_stop(sinfo);
> atmel_lcdfb_stop_clock(sinfo);
> @@ -1192,11 +1221,12 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> atmel_lcdfb_start_clock(sinfo);
> atmel_lcdfb_start(sinfo);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(1);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(1);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
>
> /* Enable FIFO & DMA errors */
> diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
> index 0f5a2fc..2eb601c 100644
> --- a/include/video/atmel_lcdc.h
> +++ b/include/video/atmel_lcdc.h
> @@ -31,39 +31,17 @@
> #define ATMEL_LCDC_WIRING_BGR 0
> #define ATMEL_LCDC_WIRING_RGB 1
>
> -struct atmel_lcdfb_config;
>
> /* LCD Controller info data structure, stored in device platform_data */
Wrong comment: it is not the "info" data structure, this time.
> -struct atmel_lcdfb_info {
> - spinlock_t lock;
> - struct fb_info *info;
> - void __iomem *mmio;
> - int irq_base;
> - struct work_struct task;
> -
> +struct atmel_lcdfb_pdata {
> unsigned int guard_time;
> - unsigned int smem_len;
> - struct platform_device *pdev;
> - struct clk *bus_clk;
> - struct clk *lcdc_clk;
> -
> -#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
> - struct backlight_device *backlight;
> - u8 bl_power;
> -#endif
> bool lcdcon_is_backlight;
> - bool lcdcon_pol_negative;
> - u8 saved_lcdcon;
> -
> u8 default_bpp;
> u8 lcd_wiring_mode;
> unsigned int default_lcdcon2;
> unsigned int default_dmacon;
> void (*atmel_lcdfb_power_control)(int on);
> struct fb_monspecs *default_monspecs;
> - u32 pseudo_palette[16];
> -
> - struct atmel_lcdfb_config *config;
> };
>
> #define ATMEL_LCDC_DMABADDR1 0x00
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-04-16 12:33 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:33 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
>
> diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
> index 629ea5f..b2a3474 100644
> --- a/arch/arm/mach-at91/at91sam9261_devices.c
> +++ b/arch/arm/mach-at91/at91sam9261_devices.c
> @@ -465,7 +465,7 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -498,7 +498,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data) {
> return;
> @@ -559,7 +559,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
> index 858c8aa..4aeaddd 100644
> --- a/arch/arm/mach-at91/at91sam9263_devices.c
> +++ b/arch/arm/mach-at91/at91sam9263_devices.c
> @@ -832,7 +832,7 @@ void __init at91_add_device_can(struct at91_can_data *data) {}
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -859,7 +859,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data)
> return;
> @@ -891,7 +891,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
> index fe626d4..82636c7 100644
> --- a/arch/arm/mach-at91/at91sam9g45_devices.c
> +++ b/arch/arm/mach-at91/at91sam9g45_devices.c
> @@ -965,7 +965,7 @@ void __init at91_add_device_isi(struct isi_platform_data *data,
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -991,7 +991,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data)
> return;
> @@ -1037,7 +1037,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
> index 352468f..a698bda 100644
> --- a/arch/arm/mach-at91/at91sam9rl_devices.c
> +++ b/arch/arm/mach-at91/at91sam9rl_devices.c
> @@ -498,7 +498,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -525,7 +525,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data) {
> return;
> @@ -557,7 +557,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
> index b446645..c819e29 100644
> --- a/arch/arm/mach-at91/board-sam9261ek.c
> +++ b/arch/arm/mach-at91/board-sam9261ek.c
> @@ -405,7 +405,7 @@ static void at91_lcdc_stn_power_control(int on)
> }
> }
>
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .default_bpp = 1,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> .default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
> @@ -460,7 +460,7 @@ static void at91_lcdc_tft_power_control(int on)
> at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
> }
>
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -475,7 +475,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> #endif
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
> index 3284df0..0fdae3f 100644
> --- a/arch/arm/mach-at91/board-sam9263ek.c
> +++ b/arch/arm/mach-at91/board-sam9263ek.c
> @@ -281,7 +281,7 @@ static void at91_lcdc_power_control(int on)
> }
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -292,7 +292,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
> index 2a94896..ef39078 100644
> --- a/arch/arm/mach-at91/board-sam9m10g45ek.c
> +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
> @@ -284,7 +284,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 32,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -295,7 +295,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
> index aa265dc..b77d7a9 100644
> --- a/arch/arm/mach-at91/board-sam9rlek.c
> +++ b/arch/arm/mach-at91/board-sam9rlek.c
> @@ -179,7 +179,7 @@ static void at91_lcdc_power_control(int on)
> }
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -191,7 +191,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h
> index 4a234fb..6c08b34 100644
> --- a/arch/arm/mach-at91/board.h
> +++ b/arch/arm/mach-at91/board.h
> @@ -107,8 +107,8 @@ extern void __init at91_add_device_pwm(u32 mask);
> extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
>
> /* LCD Controller */
> -struct atmel_lcdfb_info;
> -extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
> +struct atmel_lcdfb_pdata;
> +extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
>
> /* AC97 */
> extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
> diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
> index 2038875..dc42804 100644
> --- a/arch/avr32/boards/atngw100/evklcd10x.c
> +++ b/arch/avr32/boards/atngw100/evklcd10x.c
> @@ -58,7 +58,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 28330000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -96,7 +96,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 7000000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -134,7 +134,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 6400000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c
> index f914319..ccc9599 100644
> --- a/arch/avr32/boards/atngw100/mrmt.c
> +++ b/arch/avr32/boards/atngw100/mrmt.c
> @@ -83,7 +83,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
> .dclkmax = 9260000,
> };
>
> -static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -126,7 +126,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
> .dclkmax = 9260000,
> };
>
> -static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
> index 9392d32..653cc09 100644
> --- a/arch/avr32/boards/atstk1000/atstk1000.h
> +++ b/arch/avr32/boards/atstk1000/atstk1000.h
> @@ -10,7 +10,7 @@
> #ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
> #define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
>
> -extern struct atmel_lcdfb_info atstk1000_lcdc_data;
> +extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
>
> void atstk1000_setup_j2_leds(void);
>
> diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
> index 2d6b560..b6b88f5 100644
> --- a/arch/avr32/boards/atstk1000/setup.c
> +++ b/arch/avr32/boards/atstk1000/setup.c
> @@ -55,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = {
> .dclkmax = 30000000,
> };
>
> -struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
> index 27bd6fb..7b1f2cd 100644
> --- a/arch/avr32/boards/favr-32/setup.c
> +++ b/arch/avr32/boards/favr-32/setup.c
> @@ -125,7 +125,7 @@ static struct fb_monspecs __initdata favr32_default_monspecs = {
> .dclkmax = 28000000,
> };
>
> -struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata favr32_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
> index 9d1efd1..dc0e317 100644
> --- a/arch/avr32/boards/hammerhead/setup.c
> +++ b/arch/avr32/boards/hammerhead/setup.c
> @@ -77,7 +77,7 @@ static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
> .dclkmax = 10000000,
> };
>
> -struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata hammerhead_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
> index 85a543c..e7683ee 100644
> --- a/arch/avr32/boards/merisc/display.c
> +++ b/arch/avr32/boards/merisc/display.c
> @@ -45,7 +45,7 @@ static struct fb_monspecs merisc_fb_monspecs = {
> .dclkmax = 30000000,
> };
>
> -struct atmel_lcdfb_info merisc_lcdc_data = {
> +struct atmel_lcdfb_pdata merisc_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
> index 05358aa..1cb8e9c 100644
> --- a/arch/avr32/boards/mimc200/setup.c
> +++ b/arch/avr32/boards/mimc200/setup.c
> @@ -8,7 +8,7 @@
> * published by the Free Software Foundation.
> */
>
> -extern struct atmel_lcdfb_info mimc200_lcdc_data;
> +extern struct atmel_lcdfb_pdata mimc200_lcdc_data;
>
> #include <linux/clk.h>
> #include <linux/etherdevice.h>
> @@ -71,7 +71,7 @@ static struct fb_monspecs __initdata mimc200_default_monspecs = {
> .dclkmax = 25200000,
> };
>
> -struct atmel_lcdfb_info __initdata mimc200_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata mimc200_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
> index 7c2f668..0badb05 100644
> --- a/arch/avr32/mach-at32ap/at32ap700x.c
> +++ b/arch/avr32/mach-at32ap/at32ap700x.c
> @@ -1437,7 +1437,7 @@ fail:
> * LCDC
> * -------------------------------------------------------------------- */
> #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
> -static struct atmel_lcdfb_info atmel_lcdfb0_data;
> +static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
> static struct resource atmel_lcdfb0_resource[] = {
> {
> .start = 0xff000000,
> @@ -1465,12 +1465,12 @@ static struct clk atmel_lcdfb0_pixclk = {
> };
>
> struct platform_device *__init
> -at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> +at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
> unsigned long fbmem_start, unsigned long fbmem_len,
> u64 pin_mask)
> {
> struct platform_device *pdev;
> - struct atmel_lcdfb_info *info;
> + struct atmel_lcdfb_pdata *info;
> struct fb_monspecs *monspecs;
> struct fb_videomode *modedb;
> unsigned int modedb_size;
> @@ -1527,7 +1527,7 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> }
>
> info = pdev->dev.platform_data;
> - memcpy(info, data, sizeof(struct atmel_lcdfb_info));
> + memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
> info->default_monspecs = monspecs;
>
> pdev->name = "at32ap-lcdfb";
> diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h
> index d485b03..f1a316d 100644
> --- a/arch/avr32/mach-at32ap/include/mach/board.h
> +++ b/arch/avr32/mach-at32ap/include/mach/board.h
> @@ -44,9 +44,9 @@ struct platform_device *
> at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
> void at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n);
>
> -struct atmel_lcdfb_info;
> +struct atmel_lcdfb_pdata;
> struct platform_device *
> -at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> +at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
> unsigned long fbmem_start, unsigned long fbmem_len,
> u64 pin_mask);
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index c1a2914..98733cd4 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,12 +20,45 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <video/of_display_timing.h>
I am not sure this one is useful for this patch, maybe place it in the
4/8 one.
> #include <mach/cpu.h>
> #include <asm/gpio.h>
>
> #include <video/atmel_lcdc.h>
>
> +struct atmel_lcdfb_config {
> + bool have_alt_pixclock;
> + bool have_hozval;
> + bool have_intensity_bit;
> +};
> +
> + /* LCD Controller info data structure, stored in device platform_data */
Is comment still relevant?
> +struct atmel_lcdfb_info {
> + spinlock_t lock;
> + struct fb_info *info;
> + void __iomem *mmio;
> + int irq_base;
> + struct work_struct task;
> +
> + unsigned int smem_len;
> + struct platform_device *pdev;
> + struct clk *bus_clk;
> + struct clk *lcdc_clk;
> +
> + struct backlight_device *backlight;
> + u8 bl_power;
> + bool lcdcon_pol_negative;
> + u8 saved_lcdcon;
> +
> + u32 pseudo_palette[16];
> + bool have_intensity_bit;
> +
> + struct atmel_lcdfb_pdata pdata;
> +
> + struct atmel_lcdfb_config *config;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -34,12 +67,6 @@
> #define ATMEL_LCDC_DMA_BURST_LEN 8 /* words */
> #define ATMEL_LCDC_FIFO_SIZE 512 /* words */
>
> -struct atmel_lcdfb_config {
> - bool have_alt_pixclock;
> - bool have_hozval;
> - bool have_intensity_bit;
> -};
> -
> static struct atmel_lcdfb_config at91sam9261_config = {
> .have_hozval = true,
> .have_intensity_bit = true,
> @@ -242,6 +269,8 @@ static void exit_backlight(struct atmel_lcdfb_info *sinfo)
>
> static void init_contrast(struct atmel_lcdfb_info *sinfo)
> {
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> /* contrast pwm can be 'inverted' */
> if (sinfo->lcdcon_pol_negative)
> contrast_ctr &= ~(ATMEL_LCDC_POL_POSITIVE);
> @@ -250,7 +279,7 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
>
> - if (sinfo->lcdcon_is_backlight)
> + if (pdata->lcdcon_is_backlight)
> init_backlight(sinfo);
> }
>
> @@ -293,9 +322,11 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
>
> static void atmel_lcdfb_stop_nowait(struct atmel_lcdfb_info *sinfo)
> {
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> /* Turn off the LCD controller and the DMA controller */
> lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
> - sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
> + pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
>
> /* Wait for the LCDC core to become idle */
> while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
> @@ -315,9 +346,11 @@ static void atmel_lcdfb_stop(struct atmel_lcdfb_info *sinfo)
>
> static void atmel_lcdfb_start(struct atmel_lcdfb_info *sinfo)
> {
> - lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> + lcdc_writel(sinfo, ATMEL_LCDC_DMACON, pdata->default_dmacon);
> lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
> - (sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
> + (pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
> | ATMEL_LCDC_PWR);
> }
>
> @@ -418,6 +451,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> {
> struct device *dev = info->device;
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned long clk_value_khz;
>
> clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
> @@ -501,7 +535,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> else
> var->green.length = 6;
>
> - if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
> /* RGB:5X5 mode */
> var->red.offset = var->green.length + 5;
> var->blue.offset = 0;
> @@ -518,7 +552,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> var->transp.length = 8;
> /* fall through */
> case 24:
> - if (sinfo->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
> /* RGB:888 mode */
> var->red.offset = 16;
> var->blue.offset = 0;
> @@ -567,6 +601,7 @@ static void atmel_lcdfb_reset(struct atmel_lcdfb_info *sinfo)
> static int atmel_lcdfb_set_par(struct fb_info *info)
> {
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned long hozval_linesz;
> unsigned long value;
> unsigned long clk_value_khz;
> @@ -628,7 +663,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
>
>
> /* Initialize control register 2 */
> - value = sinfo->default_lcdcon2;
> + value = pdata->default_lcdcon2;
>
> if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
> value |= ATMEL_LCDC_INVLINE_INVERTED;
> @@ -732,6 +767,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
> unsigned int transp, struct fb_info *info)
> {
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned int val;
> u32 *pal;
> int ret = 1;
> @@ -768,8 +804,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
> */
> } else {
> /* new style BGR:565 / RGB:565 */
> - if (sinfo->lcd_wiring_mode =
> - ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB) {
> val = ((blue >> 11) & 0x001f);
> val |= ((red >> 0) & 0xf800);
> } else {
> @@ -909,7 +944,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct fb_info *info;
> struct atmel_lcdfb_info *sinfo;
> - struct atmel_lcdfb_info *pdata_sinfo;
> + struct atmel_lcdfb_pdata *pdata;
> struct fb_videomode fbmode;
> struct resource *regs = NULL;
> struct resource *map = NULL;
> @@ -927,17 +962,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> sinfo = info->par;
>
> if (dev->platform_data) {
> - pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
> - sinfo->default_bpp = pdata_sinfo->default_bpp;
> - sinfo->default_dmacon = pdata_sinfo->default_dmacon;
> - sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
> - sinfo->default_monspecs = pdata_sinfo->default_monspecs;
> - sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
> - sinfo->guard_time = pdata_sinfo->guard_time;
> - sinfo->smem_len = pdata_sinfo->smem_len;
> - sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
> - sinfo->lcdcon_pol_negative = pdata_sinfo->lcdcon_pol_negative;
> - sinfo->lcd_wiring_mode = pdata_sinfo->lcd_wiring_mode;
> + pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> + sinfo->pdata = *pdata;
> } else {
> dev_err(dev, "cannot get default configuration\n");
> goto free_info;
> @@ -953,7 +979,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> info->pseudo_palette = sinfo->pseudo_palette;
> info->fbops = &atmel_lcdfb_ops;
>
> - memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> info->fix = atmel_lcdfb_fix;
>
> /* Enable LCDC Clocks */
> @@ -971,7 +997,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>
> ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> info->monspecs.modedb_len, info->monspecs.modedb,
> - sinfo->default_bpp);
> + pdata->default_bpp);
> if (!ret) {
> dev_err(dev, "no suitable video mode found\n");
> goto stop_clk;
> @@ -1088,8 +1114,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> fb_add_videomode(&fbmode, &info->modelist);
>
> /* Power up the LCDC screen */
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(1);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(1);
>
> dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
> info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
> @@ -1134,15 +1160,17 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct fb_info *info = dev_get_drvdata(dev);
> struct atmel_lcdfb_info *sinfo;
> + struct atmel_lcdfb_pdata *pdata;
>
> if (!info || !info->par)
> return 0;
> sinfo = info->par;
> + pdata = &sinfo->pdata;
>
> cancel_work_sync(&sinfo->task);
> exit_backlight(sinfo);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(0);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(0);
> unregister_framebuffer(info);
> atmel_lcdfb_stop_clock(sinfo);
> clk_put(sinfo->lcdc_clk);
> @@ -1170,6 +1198,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> /*
> * We don't want to handle interrupts while the clock is
> @@ -1179,8 +1208,8 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
>
> sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(0);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(0);
>
> atmel_lcdfb_stop(sinfo);
> atmel_lcdfb_stop_clock(sinfo);
> @@ -1192,11 +1221,12 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> atmel_lcdfb_start_clock(sinfo);
> atmel_lcdfb_start(sinfo);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(1);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(1);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
>
> /* Enable FIFO & DMA errors */
> diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
> index 0f5a2fc..2eb601c 100644
> --- a/include/video/atmel_lcdc.h
> +++ b/include/video/atmel_lcdc.h
> @@ -31,39 +31,17 @@
> #define ATMEL_LCDC_WIRING_BGR 0
> #define ATMEL_LCDC_WIRING_RGB 1
>
> -struct atmel_lcdfb_config;
>
> /* LCD Controller info data structure, stored in device platform_data */
Wrong comment: it is not the "info" data structure, this time.
> -struct atmel_lcdfb_info {
> - spinlock_t lock;
> - struct fb_info *info;
> - void __iomem *mmio;
> - int irq_base;
> - struct work_struct task;
> -
> +struct atmel_lcdfb_pdata {
> unsigned int guard_time;
> - unsigned int smem_len;
> - struct platform_device *pdev;
> - struct clk *bus_clk;
> - struct clk *lcdc_clk;
> -
> -#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
> - struct backlight_device *backlight;
> - u8 bl_power;
> -#endif
> bool lcdcon_is_backlight;
> - bool lcdcon_pol_negative;
> - u8 saved_lcdcon;
> -
> u8 default_bpp;
> u8 lcd_wiring_mode;
> unsigned int default_lcdcon2;
> unsigned int default_dmacon;
> void (*atmel_lcdfb_power_control)(int on);
> struct fb_monspecs *default_monspecs;
> - u32 pseudo_palette[16];
> -
> - struct atmel_lcdfb_config *config;
> };
>
> #define ATMEL_LCDC_DMABADDR1 0x00
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-04-16 12:33 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:33 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
>
> diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
> index 629ea5f..b2a3474 100644
> --- a/arch/arm/mach-at91/at91sam9261_devices.c
> +++ b/arch/arm/mach-at91/at91sam9261_devices.c
> @@ -465,7 +465,7 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -498,7 +498,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data) {
> return;
> @@ -559,7 +559,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
> index 858c8aa..4aeaddd 100644
> --- a/arch/arm/mach-at91/at91sam9263_devices.c
> +++ b/arch/arm/mach-at91/at91sam9263_devices.c
> @@ -832,7 +832,7 @@ void __init at91_add_device_can(struct at91_can_data *data) {}
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -859,7 +859,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data)
> return;
> @@ -891,7 +891,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
> index fe626d4..82636c7 100644
> --- a/arch/arm/mach-at91/at91sam9g45_devices.c
> +++ b/arch/arm/mach-at91/at91sam9g45_devices.c
> @@ -965,7 +965,7 @@ void __init at91_add_device_isi(struct isi_platform_data *data,
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -991,7 +991,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data)
> return;
> @@ -1037,7 +1037,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
> index 352468f..a698bda 100644
> --- a/arch/arm/mach-at91/at91sam9rl_devices.c
> +++ b/arch/arm/mach-at91/at91sam9rl_devices.c
> @@ -498,7 +498,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
>
> #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
> static u64 lcdc_dmamask = DMA_BIT_MASK(32);
> -static struct atmel_lcdfb_info lcdc_data;
> +static struct atmel_lcdfb_pdata lcdc_data;
>
> static struct resource lcdc_resources[] = {
> [0] = {
> @@ -525,7 +525,7 @@ static struct platform_device at91_lcdc_device = {
> .num_resources = ARRAY_SIZE(lcdc_resources),
> };
>
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
> {
> if (!data) {
> return;
> @@ -557,7 +557,7 @@ void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
> platform_device_register(&at91_lcdc_device);
> }
> #else
> -void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
> +void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
> index b446645..c819e29 100644
> --- a/arch/arm/mach-at91/board-sam9261ek.c
> +++ b/arch/arm/mach-at91/board-sam9261ek.c
> @@ -405,7 +405,7 @@ static void at91_lcdc_stn_power_control(int on)
> }
> }
>
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .default_bpp = 1,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> .default_lcdcon2 = AT91SAM9261_DEFAULT_STN_LCDCON2,
> @@ -460,7 +460,7 @@ static void at91_lcdc_tft_power_control(int on)
> at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
> }
>
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -475,7 +475,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> #endif
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
> index 3284df0..0fdae3f 100644
> --- a/arch/arm/mach-at91/board-sam9263ek.c
> +++ b/arch/arm/mach-at91/board-sam9263ek.c
> @@ -281,7 +281,7 @@ static void at91_lcdc_power_control(int on)
> }
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -292,7 +292,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
> index 2a94896..ef39078 100644
> --- a/arch/arm/mach-at91/board-sam9m10g45ek.c
> +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
> @@ -284,7 +284,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 32,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -295,7 +295,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
> index aa265dc..b77d7a9 100644
> --- a/arch/arm/mach-at91/board-sam9rlek.c
> +++ b/arch/arm/mach-at91/board-sam9rlek.c
> @@ -179,7 +179,7 @@ static void at91_lcdc_power_control(int on)
> }
>
> /* Driver datas */
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
> .lcdcon_is_backlight = true,
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN,
> @@ -191,7 +191,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
> };
>
> #else
> -static struct atmel_lcdfb_info __initdata ek_lcdc_data;
> +static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
> #endif
>
>
> diff --git a/arch/arm/mach-at91/board.h b/arch/arm/mach-at91/board.h
> index 4a234fb..6c08b34 100644
> --- a/arch/arm/mach-at91/board.h
> +++ b/arch/arm/mach-at91/board.h
> @@ -107,8 +107,8 @@ extern void __init at91_add_device_pwm(u32 mask);
> extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
>
> /* LCD Controller */
> -struct atmel_lcdfb_info;
> -extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
> +struct atmel_lcdfb_pdata;
> +extern void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data);
>
> /* AC97 */
> extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
> diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
> index 2038875..dc42804 100644
> --- a/arch/avr32/boards/atngw100/evklcd10x.c
> +++ b/arch/avr32/boards/atngw100/evklcd10x.c
> @@ -58,7 +58,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 28330000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -96,7 +96,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 7000000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -134,7 +134,7 @@ static struct fb_monspecs __initdata atevklcd10x_default_monspecs = {
> .dclkmax = 6400000,
> };
>
> -static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/atngw100/mrmt.c b/arch/avr32/boards/atngw100/mrmt.c
> index f914319..ccc9599 100644
> --- a/arch/avr32/boards/atngw100/mrmt.c
> +++ b/arch/avr32/boards/atngw100/mrmt.c
> @@ -83,7 +83,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
> .dclkmax = 9260000,
> };
>
> -static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> @@ -126,7 +126,7 @@ static struct fb_monspecs __initdata lcd_fb_default_monspecs = {
> .dclkmax = 9260000,
> };
>
> -static struct atmel_lcdfb_info __initdata rmt_lcdc_data = {
> +static struct atmel_lcdfb_pdata __initdata rmt_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
> index 9392d32..653cc09 100644
> --- a/arch/avr32/boards/atstk1000/atstk1000.h
> +++ b/arch/avr32/boards/atstk1000/atstk1000.h
> @@ -10,7 +10,7 @@
> #ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
> #define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
>
> -extern struct atmel_lcdfb_info atstk1000_lcdc_data;
> +extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
>
> void atstk1000_setup_j2_leds(void);
>
> diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
> index 2d6b560..b6b88f5 100644
> --- a/arch/avr32/boards/atstk1000/setup.c
> +++ b/arch/avr32/boards/atstk1000/setup.c
> @@ -55,7 +55,7 @@ static struct fb_monspecs __initdata atstk1000_default_monspecs = {
> .dclkmax = 30000000,
> };
>
> -struct atmel_lcdfb_info __initdata atstk1000_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
> index 27bd6fb..7b1f2cd 100644
> --- a/arch/avr32/boards/favr-32/setup.c
> +++ b/arch/avr32/boards/favr-32/setup.c
> @@ -125,7 +125,7 @@ static struct fb_monspecs __initdata favr32_default_monspecs = {
> .dclkmax = 28000000,
> };
>
> -struct atmel_lcdfb_info __initdata favr32_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata favr32_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
> index 9d1efd1..dc0e317 100644
> --- a/arch/avr32/boards/hammerhead/setup.c
> +++ b/arch/avr32/boards/hammerhead/setup.c
> @@ -77,7 +77,7 @@ static struct fb_monspecs __initdata hammerhead_hda350t_monspecs = {
> .dclkmax = 10000000,
> };
>
> -struct atmel_lcdfb_info __initdata hammerhead_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata hammerhead_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
> index 85a543c..e7683ee 100644
> --- a/arch/avr32/boards/merisc/display.c
> +++ b/arch/avr32/boards/merisc/display.c
> @@ -45,7 +45,7 @@ static struct fb_monspecs merisc_fb_monspecs = {
> .dclkmax = 30000000,
> };
>
> -struct atmel_lcdfb_info merisc_lcdc_data = {
> +struct atmel_lcdfb_pdata merisc_lcdc_data = {
> .default_bpp = 24,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
> index 05358aa..1cb8e9c 100644
> --- a/arch/avr32/boards/mimc200/setup.c
> +++ b/arch/avr32/boards/mimc200/setup.c
> @@ -8,7 +8,7 @@
> * published by the Free Software Foundation.
> */
>
> -extern struct atmel_lcdfb_info mimc200_lcdc_data;
> +extern struct atmel_lcdfb_pdata mimc200_lcdc_data;
>
> #include <linux/clk.h>
> #include <linux/etherdevice.h>
> @@ -71,7 +71,7 @@ static struct fb_monspecs __initdata mimc200_default_monspecs = {
> .dclkmax = 25200000,
> };
>
> -struct atmel_lcdfb_info __initdata mimc200_lcdc_data = {
> +struct atmel_lcdfb_pdata __initdata mimc200_lcdc_data = {
> .default_bpp = 16,
> .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
> .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
> diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
> index 7c2f668..0badb05 100644
> --- a/arch/avr32/mach-at32ap/at32ap700x.c
> +++ b/arch/avr32/mach-at32ap/at32ap700x.c
> @@ -1437,7 +1437,7 @@ fail:
> * LCDC
> * -------------------------------------------------------------------- */
> #if defined(CONFIG_CPU_AT32AP7000) || defined(CONFIG_CPU_AT32AP7002)
> -static struct atmel_lcdfb_info atmel_lcdfb0_data;
> +static struct atmel_lcdfb_pdata atmel_lcdfb0_data;
> static struct resource atmel_lcdfb0_resource[] = {
> {
> .start = 0xff000000,
> @@ -1465,12 +1465,12 @@ static struct clk atmel_lcdfb0_pixclk = {
> };
>
> struct platform_device *__init
> -at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> +at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
> unsigned long fbmem_start, unsigned long fbmem_len,
> u64 pin_mask)
> {
> struct platform_device *pdev;
> - struct atmel_lcdfb_info *info;
> + struct atmel_lcdfb_pdata *info;
> struct fb_monspecs *monspecs;
> struct fb_videomode *modedb;
> unsigned int modedb_size;
> @@ -1527,7 +1527,7 @@ at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> }
>
> info = pdev->dev.platform_data;
> - memcpy(info, data, sizeof(struct atmel_lcdfb_info));
> + memcpy(info, data, sizeof(struct atmel_lcdfb_pdata));
> info->default_monspecs = monspecs;
>
> pdev->name = "at32ap-lcdfb";
> diff --git a/arch/avr32/mach-at32ap/include/mach/board.h b/arch/avr32/mach-at32ap/include/mach/board.h
> index d485b03..f1a316d 100644
> --- a/arch/avr32/mach-at32ap/include/mach/board.h
> +++ b/arch/avr32/mach-at32ap/include/mach/board.h
> @@ -44,9 +44,9 @@ struct platform_device *
> at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
> void at32_spi_setup_slaves(unsigned int bus_num, struct spi_board_info *b, unsigned int n);
>
> -struct atmel_lcdfb_info;
> +struct atmel_lcdfb_pdata;
> struct platform_device *
> -at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
> +at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_pdata *data,
> unsigned long fbmem_start, unsigned long fbmem_len,
> u64 pin_mask);
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index c1a2914..98733cd4 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,12 +20,45 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <video/of_display_timing.h>
I am not sure this one is useful for this patch, maybe place it in the
4/8 one.
> #include <mach/cpu.h>
> #include <asm/gpio.h>
>
> #include <video/atmel_lcdc.h>
>
> +struct atmel_lcdfb_config {
> + bool have_alt_pixclock;
> + bool have_hozval;
> + bool have_intensity_bit;
> +};
> +
> + /* LCD Controller info data structure, stored in device platform_data */
Is comment still relevant?
> +struct atmel_lcdfb_info {
> + spinlock_t lock;
> + struct fb_info *info;
> + void __iomem *mmio;
> + int irq_base;
> + struct work_struct task;
> +
> + unsigned int smem_len;
> + struct platform_device *pdev;
> + struct clk *bus_clk;
> + struct clk *lcdc_clk;
> +
> + struct backlight_device *backlight;
> + u8 bl_power;
> + bool lcdcon_pol_negative;
> + u8 saved_lcdcon;
> +
> + u32 pseudo_palette[16];
> + bool have_intensity_bit;
> +
> + struct atmel_lcdfb_pdata pdata;
> +
> + struct atmel_lcdfb_config *config;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -34,12 +67,6 @@
> #define ATMEL_LCDC_DMA_BURST_LEN 8 /* words */
> #define ATMEL_LCDC_FIFO_SIZE 512 /* words */
>
> -struct atmel_lcdfb_config {
> - bool have_alt_pixclock;
> - bool have_hozval;
> - bool have_intensity_bit;
> -};
> -
> static struct atmel_lcdfb_config at91sam9261_config = {
> .have_hozval = true,
> .have_intensity_bit = true,
> @@ -242,6 +269,8 @@ static void exit_backlight(struct atmel_lcdfb_info *sinfo)
>
> static void init_contrast(struct atmel_lcdfb_info *sinfo)
> {
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> /* contrast pwm can be 'inverted' */
> if (sinfo->lcdcon_pol_negative)
> contrast_ctr &= ~(ATMEL_LCDC_POL_POSITIVE);
> @@ -250,7 +279,7 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, contrast_ctr);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
>
> - if (sinfo->lcdcon_is_backlight)
> + if (pdata->lcdcon_is_backlight)
> init_backlight(sinfo);
> }
>
> @@ -293,9 +322,11 @@ static unsigned long compute_hozval(struct atmel_lcdfb_info *sinfo,
>
> static void atmel_lcdfb_stop_nowait(struct atmel_lcdfb_info *sinfo)
> {
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> /* Turn off the LCD controller and the DMA controller */
> lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
> - sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
> + pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET);
>
> /* Wait for the LCDC core to become idle */
> while (lcdc_readl(sinfo, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
> @@ -315,9 +346,11 @@ static void atmel_lcdfb_stop(struct atmel_lcdfb_info *sinfo)
>
> static void atmel_lcdfb_start(struct atmel_lcdfb_info *sinfo)
> {
> - lcdc_writel(sinfo, ATMEL_LCDC_DMACON, sinfo->default_dmacon);
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> + lcdc_writel(sinfo, ATMEL_LCDC_DMACON, pdata->default_dmacon);
> lcdc_writel(sinfo, ATMEL_LCDC_PWRCON,
> - (sinfo->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
> + (pdata->guard_time << ATMEL_LCDC_GUARDT_OFFSET)
> | ATMEL_LCDC_PWR);
> }
>
> @@ -418,6 +451,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> {
> struct device *dev = info->device;
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned long clk_value_khz;
>
> clk_value_khz = clk_get_rate(sinfo->lcdc_clk) / 1000;
> @@ -501,7 +535,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> else
> var->green.length = 6;
>
> - if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> /* RGB:5X5 mode */
> var->red.offset = var->green.length + 5;
> var->blue.offset = 0;
> @@ -518,7 +552,7 @@ static int atmel_lcdfb_check_var(struct fb_var_screeninfo *var,
> var->transp.length = 8;
> /* fall through */
> case 24:
> - if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> /* RGB:888 mode */
> var->red.offset = 16;
> var->blue.offset = 0;
> @@ -567,6 +601,7 @@ static void atmel_lcdfb_reset(struct atmel_lcdfb_info *sinfo)
> static int atmel_lcdfb_set_par(struct fb_info *info)
> {
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned long hozval_linesz;
> unsigned long value;
> unsigned long clk_value_khz;
> @@ -628,7 +663,7 @@ static int atmel_lcdfb_set_par(struct fb_info *info)
>
>
> /* Initialize control register 2 */
> - value = sinfo->default_lcdcon2;
> + value = pdata->default_lcdcon2;
>
> if (!(info->var.sync & FB_SYNC_HOR_HIGH_ACT))
> value |= ATMEL_LCDC_INVLINE_INVERTED;
> @@ -732,6 +767,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
> unsigned int transp, struct fb_info *info)
> {
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> unsigned int val;
> u32 *pal;
> int ret = 1;
> @@ -768,8 +804,7 @@ static int atmel_lcdfb_setcolreg(unsigned int regno, unsigned int red,
> */
> } else {
> /* new style BGR:565 / RGB:565 */
> - if (sinfo->lcd_wiring_mode ==
> - ATMEL_LCDC_WIRING_RGB) {
> + if (pdata->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB) {
> val = ((blue >> 11) & 0x001f);
> val |= ((red >> 0) & 0xf800);
> } else {
> @@ -909,7 +944,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct fb_info *info;
> struct atmel_lcdfb_info *sinfo;
> - struct atmel_lcdfb_info *pdata_sinfo;
> + struct atmel_lcdfb_pdata *pdata;
> struct fb_videomode fbmode;
> struct resource *regs = NULL;
> struct resource *map = NULL;
> @@ -927,17 +962,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> sinfo = info->par;
>
> if (dev->platform_data) {
> - pdata_sinfo = (struct atmel_lcdfb_info *)dev->platform_data;
> - sinfo->default_bpp = pdata_sinfo->default_bpp;
> - sinfo->default_dmacon = pdata_sinfo->default_dmacon;
> - sinfo->default_lcdcon2 = pdata_sinfo->default_lcdcon2;
> - sinfo->default_monspecs = pdata_sinfo->default_monspecs;
> - sinfo->atmel_lcdfb_power_control = pdata_sinfo->atmel_lcdfb_power_control;
> - sinfo->guard_time = pdata_sinfo->guard_time;
> - sinfo->smem_len = pdata_sinfo->smem_len;
> - sinfo->lcdcon_is_backlight = pdata_sinfo->lcdcon_is_backlight;
> - sinfo->lcdcon_pol_negative = pdata_sinfo->lcdcon_pol_negative;
> - sinfo->lcd_wiring_mode = pdata_sinfo->lcd_wiring_mode;
> + pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> + sinfo->pdata = *pdata;
> } else {
> dev_err(dev, "cannot get default configuration\n");
> goto free_info;
> @@ -953,7 +979,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> info->pseudo_palette = sinfo->pseudo_palette;
> info->fbops = &atmel_lcdfb_ops;
>
> - memcpy(&info->monspecs, sinfo->default_monspecs, sizeof(info->monspecs));
> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> info->fix = atmel_lcdfb_fix;
>
> /* Enable LCDC Clocks */
> @@ -971,7 +997,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>
> ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> info->monspecs.modedb_len, info->monspecs.modedb,
> - sinfo->default_bpp);
> + pdata->default_bpp);
> if (!ret) {
> dev_err(dev, "no suitable video mode found\n");
> goto stop_clk;
> @@ -1088,8 +1114,8 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> fb_add_videomode(&fbmode, &info->modelist);
>
> /* Power up the LCDC screen */
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(1);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(1);
>
> dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
> info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
> @@ -1134,15 +1160,17 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
> struct device *dev = &pdev->dev;
> struct fb_info *info = dev_get_drvdata(dev);
> struct atmel_lcdfb_info *sinfo;
> + struct atmel_lcdfb_pdata *pdata;
>
> if (!info || !info->par)
> return 0;
> sinfo = info->par;
> + pdata = &sinfo->pdata;
>
> cancel_work_sync(&sinfo->task);
> exit_backlight(sinfo);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(0);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(0);
> unregister_framebuffer(info);
> atmel_lcdfb_stop_clock(sinfo);
> clk_put(sinfo->lcdc_clk);
> @@ -1170,6 +1198,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> /*
> * We don't want to handle interrupts while the clock is
> @@ -1179,8 +1208,8 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
>
> sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(0);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(0);
>
> atmel_lcdfb_stop(sinfo);
> atmel_lcdfb_stop_clock(sinfo);
> @@ -1192,11 +1221,12 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> atmel_lcdfb_start_clock(sinfo);
> atmel_lcdfb_start(sinfo);
> - if (sinfo->atmel_lcdfb_power_control)
> - sinfo->atmel_lcdfb_power_control(1);
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(1);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
>
> /* Enable FIFO & DMA errors */
> diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
> index 0f5a2fc..2eb601c 100644
> --- a/include/video/atmel_lcdc.h
> +++ b/include/video/atmel_lcdc.h
> @@ -31,39 +31,17 @@
> #define ATMEL_LCDC_WIRING_BGR 0
> #define ATMEL_LCDC_WIRING_RGB 1
>
> -struct atmel_lcdfb_config;
>
> /* LCD Controller info data structure, stored in device platform_data */
Wrong comment: it is not the "info" data structure, this time.
> -struct atmel_lcdfb_info {
> - spinlock_t lock;
> - struct fb_info *info;
> - void __iomem *mmio;
> - int irq_base;
> - struct work_struct task;
> -
> +struct atmel_lcdfb_pdata {
> unsigned int guard_time;
> - unsigned int smem_len;
> - struct platform_device *pdev;
> - struct clk *bus_clk;
> - struct clk *lcdc_clk;
> -
> -#ifdef CONFIG_BACKLIGHT_ATMEL_LCDC
> - struct backlight_device *backlight;
> - u8 bl_power;
> -#endif
> bool lcdcon_is_backlight;
> - bool lcdcon_pol_negative;
> - u8 saved_lcdcon;
> -
> u8 default_bpp;
> u8 lcd_wiring_mode;
> unsigned int default_lcdcon2;
> unsigned int default_dmacon;
> void (*atmel_lcdfb_power_control)(int on);
> struct fb_monspecs *default_monspecs;
> - u32 pseudo_palette[16];
> -
> - struct atmel_lcdfb_config *config;
> };
>
> #define ATMEL_LCDC_DMABADDR1 0x00
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-16 12:35 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:35 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Andrew Morton, devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ,
linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> to simplify the check on the presence of the callback
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
> Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
Simple and nice
Acked-by: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
> Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
> ---
> drivers/video/atmel_lcdfb.c | 22 +++++++++++-----------
> 1 file changed, 11 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index 98733cd4..9574c47 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -283,6 +283,13 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
> init_backlight(sinfo);
> }
>
> +static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int on)
> +{
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(on);
> +}
>
> static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
> .type = FB_TYPE_PACKED_PIXELS,
> @@ -1114,8 +1121,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> fb_add_videomode(&fbmode, &info->modelist);
>
> /* Power up the LCDC screen */
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(1);
> + atmel_lcdfb_power_control(sinfo, 1);
>
> dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
> info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
> @@ -1169,8 +1175,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
>
> cancel_work_sync(&sinfo->task);
> exit_backlight(sinfo);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(0);
> + atmel_lcdfb_power_control(sinfo, 0);
> unregister_framebuffer(info);
> atmel_lcdfb_stop_clock(sinfo);
> clk_put(sinfo->lcdc_clk);
> @@ -1198,7 +1203,6 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> - struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> /*
> * We don't want to handle interrupts while the clock is
> @@ -1208,9 +1212,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
>
> sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(0);
> -
> + atmel_lcdfb_power_control(sinfo, 0);
> atmel_lcdfb_stop(sinfo);
> atmel_lcdfb_stop_clock(sinfo);
>
> @@ -1221,12 +1223,10 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> - struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> atmel_lcdfb_start_clock(sinfo);
> atmel_lcdfb_start(sinfo);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(1);
> + atmel_lcdfb_power_control(sinfo, 1);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
>
> /* Enable FIFO & DMA errors */
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control
@ 2013-04-16 12:35 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:35 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> to simplify the check on the presence of the callback
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Simple and nice
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> drivers/video/atmel_lcdfb.c | 22 +++++++++++-----------
> 1 file changed, 11 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index 98733cd4..9574c47 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -283,6 +283,13 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
> init_backlight(sinfo);
> }
>
> +static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int on)
> +{
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(on);
> +}
>
> static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
> .type = FB_TYPE_PACKED_PIXELS,
> @@ -1114,8 +1121,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> fb_add_videomode(&fbmode, &info->modelist);
>
> /* Power up the LCDC screen */
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(1);
> + atmel_lcdfb_power_control(sinfo, 1);
>
> dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
> info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
> @@ -1169,8 +1175,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
>
> cancel_work_sync(&sinfo->task);
> exit_backlight(sinfo);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(0);
> + atmel_lcdfb_power_control(sinfo, 0);
> unregister_framebuffer(info);
> atmel_lcdfb_stop_clock(sinfo);
> clk_put(sinfo->lcdc_clk);
> @@ -1198,7 +1203,6 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> - struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> /*
> * We don't want to handle interrupts while the clock is
> @@ -1208,9 +1212,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
>
> sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(0);
> -
> + atmel_lcdfb_power_control(sinfo, 0);
> atmel_lcdfb_stop(sinfo);
> atmel_lcdfb_stop_clock(sinfo);
>
> @@ -1221,12 +1223,10 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> - struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> atmel_lcdfb_start_clock(sinfo);
> atmel_lcdfb_start(sinfo);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(1);
> + atmel_lcdfb_power_control(sinfo, 1);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
>
> /* Enable FIFO & DMA errors */
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control
@ 2013-04-16 12:35 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:35 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> to simplify the check on the presence of the callback
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Simple and nice
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> drivers/video/atmel_lcdfb.c | 22 +++++++++++-----------
> 1 file changed, 11 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index 98733cd4..9574c47 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -283,6 +283,13 @@ static void init_contrast(struct atmel_lcdfb_info *sinfo)
> init_backlight(sinfo);
> }
>
> +static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int on)
> +{
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> +
> + if (pdata->atmel_lcdfb_power_control)
> + pdata->atmel_lcdfb_power_control(on);
> +}
>
> static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
> .type = FB_TYPE_PACKED_PIXELS,
> @@ -1114,8 +1121,7 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> fb_add_videomode(&fbmode, &info->modelist);
>
> /* Power up the LCDC screen */
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(1);
> + atmel_lcdfb_power_control(sinfo, 1);
>
> dev_info(dev, "fb%d: Atmel LCDC at 0x%08lx (mapped at %p), irq %d\n",
> info->node, info->fix.mmio_start, sinfo->mmio, sinfo->irq_base);
> @@ -1169,8 +1175,7 @@ static int __exit atmel_lcdfb_remove(struct platform_device *pdev)
>
> cancel_work_sync(&sinfo->task);
> exit_backlight(sinfo);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(0);
> + atmel_lcdfb_power_control(sinfo, 0);
> unregister_framebuffer(info);
> atmel_lcdfb_stop_clock(sinfo);
> clk_put(sinfo->lcdc_clk);
> @@ -1198,7 +1203,6 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> - struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> /*
> * We don't want to handle interrupts while the clock is
> @@ -1208,9 +1212,7 @@ static int atmel_lcdfb_suspend(struct platform_device *pdev, pm_message_t mesg)
>
> sinfo->saved_lcdcon = lcdc_readl(sinfo, ATMEL_LCDC_CONTRAST_CTR);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, 0);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(0);
> -
> + atmel_lcdfb_power_control(sinfo, 0);
> atmel_lcdfb_stop(sinfo);
> atmel_lcdfb_stop_clock(sinfo);
>
> @@ -1221,12 +1223,10 @@ static int atmel_lcdfb_resume(struct platform_device *pdev)
> {
> struct fb_info *info = platform_get_drvdata(pdev);
> struct atmel_lcdfb_info *sinfo = info->par;
> - struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> atmel_lcdfb_start_clock(sinfo);
> atmel_lcdfb_start(sinfo);
> - if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(1);
> + atmel_lcdfb_power_control(sinfo, 1);
> lcdc_writel(sinfo, ATMEL_LCDC_CONTRAST_CTR, sinfo->saved_lcdcon);
>
> /* Enable FIFO & DMA errors */
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-16 12:38 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:38 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Andrew Morton, devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ,
linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> so we can use have list gpio as example (probe via DT)
Please refine the commit message: I do not understand.
After reading the patch, it seems obvious that more explanations are
needed in the message.
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
> Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
> Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
> ---
> arch/arm/mach-at91/board-sam9261ek.c | 4 ++--
> arch/arm/mach-at91/board-sam9263ek.c | 2 +-
> arch/arm/mach-at91/board-sam9rlek.c | 2 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 2 +-
> drivers/video/atmel_lcdfb.c | 2 +-
> include/video/atmel_lcdc.h | 4 +++-
> 6 files changed, 9 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
> index c819e29..9a6618a 100644
> --- a/arch/arm/mach-at91/board-sam9261ek.c
> +++ b/arch/arm/mach-at91/board-sam9261ek.c
> @@ -393,7 +393,7 @@ static struct fb_monspecs at91fb_default_stn_monspecs = {
> | ATMEL_LCDC_IFWIDTH_4 \
> | ATMEL_LCDC_SCANMOD_SINGLE)
>
> -static void at91_lcdc_stn_power_control(int on)
> +static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> /* backlight */
> if (on) { /* power up */
> @@ -452,7 +452,7 @@ static struct fb_monspecs at91fb_default_tft_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_tft_power_control(int on)
> +static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> if (on)
> at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
> index 0fdae3f..8b4942c 100644
> --- a/arch/arm/mach-at91/board-sam9263ek.c
> +++ b/arch/arm/mach-at91/board-sam9263ek.c
> @@ -275,7 +275,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_power_control(int on)
> +static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> at91_set_gpio_value(AT91_PIN_PA30, on);
> }
> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
> index b77d7a9..604eecf 100644
> --- a/arch/arm/mach-at91/board-sam9rlek.c
> +++ b/arch/arm/mach-at91/board-sam9rlek.c
> @@ -170,7 +170,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_power_control(int on)
> +static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> if (on)
> at91_set_gpio_value(AT91_PIN_PC1, 0); /* power up */
> diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
> index dc42804..64919b0 100644
> --- a/arch/avr32/boards/atngw100/evklcd10x.c
> +++ b/arch/avr32/boards/atngw100/evklcd10x.c
> @@ -145,7 +145,7 @@ static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> };
> #endif
>
> -static void atevklcd10x_lcdc_power_control(int on)
> +static void atevklcd10x_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> gpio_set_value(GPIO_PIN_PB(15), on);
> }
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index 9574c47..f67e226 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -288,7 +288,7 @@ static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int
> struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(on);
> + pdata->atmel_lcdfb_power_control(pdata, on);
> }
>
> static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
> diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
> index 2eb601c..f624c51 100644
> --- a/include/video/atmel_lcdc.h
> +++ b/include/video/atmel_lcdc.h
> @@ -40,8 +40,10 @@ struct atmel_lcdfb_pdata {
> u8 lcd_wiring_mode;
> unsigned int default_lcdcon2;
> unsigned int default_dmacon;
> - void (*atmel_lcdfb_power_control)(int on);
> + void (*atmel_lcdfb_power_control)(struct atmel_lcdfb_pdata *pdata, int on);
> struct fb_monspecs *default_monspecs;
> +
> + struct list_head pwr_gpios;
> };
>
> #define ATMEL_LCDC_DMABADDR1 0x00
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params
@ 2013-04-16 12:38 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:38 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> so we can use have list gpio as example (probe via DT)
Please refine the commit message: I do not understand.
After reading the patch, it seems obvious that more explanations are
needed in the message.
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> arch/arm/mach-at91/board-sam9261ek.c | 4 ++--
> arch/arm/mach-at91/board-sam9263ek.c | 2 +-
> arch/arm/mach-at91/board-sam9rlek.c | 2 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 2 +-
> drivers/video/atmel_lcdfb.c | 2 +-
> include/video/atmel_lcdc.h | 4 +++-
> 6 files changed, 9 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
> index c819e29..9a6618a 100644
> --- a/arch/arm/mach-at91/board-sam9261ek.c
> +++ b/arch/arm/mach-at91/board-sam9261ek.c
> @@ -393,7 +393,7 @@ static struct fb_monspecs at91fb_default_stn_monspecs = {
> | ATMEL_LCDC_IFWIDTH_4 \
> | ATMEL_LCDC_SCANMOD_SINGLE)
>
> -static void at91_lcdc_stn_power_control(int on)
> +static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> /* backlight */
> if (on) { /* power up */
> @@ -452,7 +452,7 @@ static struct fb_monspecs at91fb_default_tft_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_tft_power_control(int on)
> +static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> if (on)
> at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
> index 0fdae3f..8b4942c 100644
> --- a/arch/arm/mach-at91/board-sam9263ek.c
> +++ b/arch/arm/mach-at91/board-sam9263ek.c
> @@ -275,7 +275,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_power_control(int on)
> +static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> at91_set_gpio_value(AT91_PIN_PA30, on);
> }
> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
> index b77d7a9..604eecf 100644
> --- a/arch/arm/mach-at91/board-sam9rlek.c
> +++ b/arch/arm/mach-at91/board-sam9rlek.c
> @@ -170,7 +170,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_power_control(int on)
> +static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> if (on)
> at91_set_gpio_value(AT91_PIN_PC1, 0); /* power up */
> diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
> index dc42804..64919b0 100644
> --- a/arch/avr32/boards/atngw100/evklcd10x.c
> +++ b/arch/avr32/boards/atngw100/evklcd10x.c
> @@ -145,7 +145,7 @@ static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> };
> #endif
>
> -static void atevklcd10x_lcdc_power_control(int on)
> +static void atevklcd10x_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> gpio_set_value(GPIO_PIN_PB(15), on);
> }
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index 9574c47..f67e226 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -288,7 +288,7 @@ static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int
> struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(on);
> + pdata->atmel_lcdfb_power_control(pdata, on);
> }
>
> static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
> diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
> index 2eb601c..f624c51 100644
> --- a/include/video/atmel_lcdc.h
> +++ b/include/video/atmel_lcdc.h
> @@ -40,8 +40,10 @@ struct atmel_lcdfb_pdata {
> u8 lcd_wiring_mode;
> unsigned int default_lcdcon2;
> unsigned int default_dmacon;
> - void (*atmel_lcdfb_power_control)(int on);
> + void (*atmel_lcdfb_power_control)(struct atmel_lcdfb_pdata *pdata, int on);
> struct fb_monspecs *default_monspecs;
> +
> + struct list_head pwr_gpios;
> };
>
> #define ATMEL_LCDC_DMABADDR1 0x00
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params
@ 2013-04-16 12:38 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 12:38 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> so we can use have list gpio as example (probe via DT)
Please refine the commit message: I do not understand.
After reading the patch, it seems obvious that more explanations are
needed in the message.
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> arch/arm/mach-at91/board-sam9261ek.c | 4 ++--
> arch/arm/mach-at91/board-sam9263ek.c | 2 +-
> arch/arm/mach-at91/board-sam9rlek.c | 2 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 2 +-
> drivers/video/atmel_lcdfb.c | 2 +-
> include/video/atmel_lcdc.h | 4 +++-
> 6 files changed, 9 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
> index c819e29..9a6618a 100644
> --- a/arch/arm/mach-at91/board-sam9261ek.c
> +++ b/arch/arm/mach-at91/board-sam9261ek.c
> @@ -393,7 +393,7 @@ static struct fb_monspecs at91fb_default_stn_monspecs = {
> | ATMEL_LCDC_IFWIDTH_4 \
> | ATMEL_LCDC_SCANMOD_SINGLE)
>
> -static void at91_lcdc_stn_power_control(int on)
> +static void at91_lcdc_stn_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> /* backlight */
> if (on) { /* power up */
> @@ -452,7 +452,7 @@ static struct fb_monspecs at91fb_default_tft_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_tft_power_control(int on)
> +static void at91_lcdc_tft_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> if (on)
> at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
> diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
> index 0fdae3f..8b4942c 100644
> --- a/arch/arm/mach-at91/board-sam9263ek.c
> +++ b/arch/arm/mach-at91/board-sam9263ek.c
> @@ -275,7 +275,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_power_control(int on)
> +static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> at91_set_gpio_value(AT91_PIN_PA30, on);
> }
> diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
> index b77d7a9..604eecf 100644
> --- a/arch/arm/mach-at91/board-sam9rlek.c
> +++ b/arch/arm/mach-at91/board-sam9rlek.c
> @@ -170,7 +170,7 @@ static struct fb_monspecs at91fb_default_monspecs = {
> | ATMEL_LCDC_DISTYPE_TFT \
> | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
>
> -static void at91_lcdc_power_control(int on)
> +static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> if (on)
> at91_set_gpio_value(AT91_PIN_PC1, 0); /* power up */
> diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
> index dc42804..64919b0 100644
> --- a/arch/avr32/boards/atngw100/evklcd10x.c
> +++ b/arch/avr32/boards/atngw100/evklcd10x.c
> @@ -145,7 +145,7 @@ static struct atmel_lcdfb_pdata __initdata atevklcd10x_lcdc_data = {
> };
> #endif
>
> -static void atevklcd10x_lcdc_power_control(int on)
> +static void atevklcd10x_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
> {
> gpio_set_value(GPIO_PIN_PB(15), on);
> }
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index 9574c47..f67e226 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -288,7 +288,7 @@ static inline void atmel_lcdfb_power_control(struct atmel_lcdfb_info *sinfo, int
> struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>
> if (pdata->atmel_lcdfb_power_control)
> - pdata->atmel_lcdfb_power_control(on);
> + pdata->atmel_lcdfb_power_control(pdata, on);
> }
>
> static struct fb_fix_screeninfo atmel_lcdfb_fix __initdata = {
> diff --git a/include/video/atmel_lcdc.h b/include/video/atmel_lcdc.h
> index 2eb601c..f624c51 100644
> --- a/include/video/atmel_lcdc.h
> +++ b/include/video/atmel_lcdc.h
> @@ -40,8 +40,10 @@ struct atmel_lcdfb_pdata {
> u8 lcd_wiring_mode;
> unsigned int default_lcdcon2;
> unsigned int default_dmacon;
> - void (*atmel_lcdfb_power_control)(int on);
> + void (*atmel_lcdfb_power_control)(struct atmel_lcdfb_pdata *pdata, int on);
> struct fb_monspecs *default_monspecs;
> +
> + struct list_head pwr_gpios;
> };
>
> #define ATMEL_LCDC_DMABADDR1 0x00
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-16 13:42 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 13:42 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Andrew Morton, devicetree-discuss, linux-fbdev, linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> get display timings from device tree
> Use videomode helpers to get display timings and configurations from
> device tree
2 sentences? Simply elaborate the 2nd one and it will be good.
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> drivers/video/Kconfig | 2 +
> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> 3 files changed, 289 insertions(+), 32 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> new file mode 100644
> index 0000000..1ec175e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
is even more self-explanatory...
> @@ -0,0 +1,75 @@
> +Atmel LCDC Framebuffer
> +-----------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + "atmel,at91sam9261-lcdc" ,
> + "atmel,at91sam9263-lcdc" ,
> + "atmel,at91sam9g10-lcdc" ,
> + "atmel,at91sam9g45-lcdc" ,
> + "atmel,at91sam9g45es-lcdc" ,
> + "atmel,at91sam9rl-lcdc" ,
> + "atmel,at32ap-lcdc"
> +- reg : Should contain 1 register ranges(address and length)
> +- interrupts : framebuffer controller interrupt
> +- display: a phandle pointing to the display node
> +
> +Required nodes:
> +- display: a display node is required to initialize the lcd panel
> + This should be in the board dts.
> +- default-mode: a videomode within the display with timing parameters
> + as specified below.
> +
> +Example:
> +
> + fb0: fb@0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + display = <&display0>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + };
> +
> +Atmel LCDC Display
> +-----------------------------------------------------
> +Required properties (as per of_videomode_helper):
Can you please point somewhere to the documentation:
Documentation/devicetree/bindings/video/display-timing.txt
> + - atmel,dmacon: dma controler configuration
Typo: controller.
> + - atmel,lcdcon2: lcd controler configuration
Ditto
> + - atmel,guard-time: lcd guard time (Delay in frame periods)
periods -> period, no?
> + - bits-per-pixel: lcd panel bit-depth.
> +
> +Optional properties (as per of_videomode_helper):
> + - atmel,lcdcon-backlight: enable backlight
> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
Is it a sting, or a number (as seen below)? If it is a number, please
tell how to choose the index.
> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
> +
> +Example:
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 4c1546f..0687482 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1018,6 +1018,8 @@ config FB_ATMEL
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select FB_MODE_HELPERS
> + select OF_VIDEOMODE
> help
> This enables support for the AT91/AT32 LCD Controller.
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index f67e226..4a31570 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,7 +20,11 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <video/of_display_timing.h>
As said in patch 1/8, this one belongs to this 4/8 patch.
> +#include <video/videomode.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> struct atmel_lcdfb_config *config;
> };
>
> +struct atmel_lcdfb_power_ctrl_gpio {
> + int gpio;
> + int active_low;
> +
> + struct list_head list;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> clk_disable(sinfo->lcdc_clk);
> }
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> +
> +static const char *atmel_lcdfb_wiring_modes[] = {
> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> +};
> +
> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> +{
> + const char *mode;
> + int err, i;
> +
> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> + if (err < 0)
> + return ATMEL_LCDC_WIRING_BGR;
> +
> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> + return i;
> +
> + return -ENODEV;
> +}
> +
> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> +{
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> +
> + list_for_each_entry(og, &pdata->pwr_gpios, list)
> + gpio_set_value(og->gpio, on);
> +}
> +
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + struct fb_info *info = sinfo->info;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> + struct fb_var_screeninfo *var = &info->var;
> + struct device *dev = &sinfo->pdev->dev;
> + struct device_node *np =dev->of_node;
> + struct device_node *display_np;
> + struct device_node *timings_np;
> + struct display_timings *timings;
> + enum of_gpio_flags flags;
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> + bool is_gpio_power = false;
> + int ret = -ENOENT;
> + int i, gpio;
> +
> + sinfo->config = (struct atmel_lcdfb_config*)
> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
Please split it in 2 steps, otherwise the day that the drivers doesn't
find the device in dt_ids table, it hangs here with an Oops.
> +
> + display_np = of_parse_phandle(np, "display", 0);
> + if (!display_np) {
> + dev_err(dev, "failed to find display phandle\n");
> + return -ENOENT;
> + }
> +
> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,guard-time\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
No, wrong error message.
> + goto put_display_node;
> + }
> +
> + ret = -ENOMEM;
> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> + i, &flags);
> + if (gpio < 0)
> + continue;
> +
> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> + if (!og)
> + goto put_display_node;
> +
> + og->gpio = gpio;
> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> + is_gpio_power = true;
> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> + if (ret) {
> + dev_err(dev, "request gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> +
> + ret = gpio_direction_output(gpio, og->active_low);
> + if (ret) {
> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> + }
> +
> + if (is_gpio_power)
> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> +
> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> + if (ret < 0) {
> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> + goto put_display_node;
> + }
> + pdata->lcd_wiring_mode = ret;
> +
> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
> +
> + timings = of_get_display_timings(display_np);
> + if (!timings) {
> + dev_err(dev, "failed to get display timings\n");
> + goto put_display_node;
> + }
> +
> + timings_np = of_find_node_by_name(display_np, "display-timings");
> + if (!timings_np) {
> + dev_err(dev, "failed to find display-timings node\n");
> + goto put_display_node;
> + }
> +
> + for (i = 0; i < of_get_child_count(timings_np); i++) {
> + struct videomode vm;
> + struct fb_videomode fb_vm;
> +
> + ret = videomode_from_timing(timings, &vm, i);
> + if (ret < 0)
> + goto put_timings_node;
> + ret = fb_videomode_from_videomode(&vm, &fb_vm);
> + if (ret < 0)
> + goto put_timings_node;
> +
> + fb_add_videomode(&fb_vm, &info->modelist);
> + }
> +
> + return 0;
> +
> +put_timings_node:
> + of_node_put(timings_np);
> +put_display_node:
> + of_node_put(display_np);
> + return ret;
> +}
> +#else
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + return 0;
> +}
> +#endif
>
> static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> struct fb_info *info;
> struct atmel_lcdfb_info *sinfo;
> - struct atmel_lcdfb_pdata *pdata;
> - struct fb_videomode fbmode;
> + struct atmel_lcdfb_pdata *pdata = NULL;
> struct resource *regs = NULL;
> struct resource *map = NULL;
> + struct fb_modelist *modelist;
> int ret;
>
> dev_dbg(dev, "%s BEGIN\n", __func__);
> @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> }
>
> sinfo = info->par;
> + sinfo->pdev = pdev;
> + sinfo->info = info;
> +
> + INIT_LIST_HEAD(&info->modelist);
>
> - if (dev->platform_data) {
> - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> + if (pdev->dev.of_node) {
> + ret = atmel_lcdfb_of_init(sinfo);
> + if (ret)
> + goto free_info;
> + } else if (dev->platform_data) {
> + struct fb_monspecs *monspecs;
> + int i;
> +
> + pdata = dev->platform_data;
> + monspecs = pdata->default_monspecs;
> sinfo->pdata = *pdata;
> +
> + for (i = 0; i < monspecs->modedb_len; i++)
> + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
> +
> + sinfo->config = atmel_lcdfb_get_config(pdev);
> +
> + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> } else {
> dev_err(dev, "cannot get default configuration\n");
> goto free_info;
> }
> - sinfo->info = info;
> - sinfo->pdev = pdev;
> - sinfo->config = atmel_lcdfb_get_config(pdev);
> +
> if (!sinfo->config)
> goto free_info;
>
> @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> info->pseudo_palette = sinfo->pseudo_palette;
> info->fbops = &atmel_lcdfb_ops;
>
> - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> info->fix = atmel_lcdfb_fix;
>
> /* Enable LCDC Clocks */
> @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> }
> atmel_lcdfb_start_clock(sinfo);
>
> - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> - info->monspecs.modedb_len, info->monspecs.modedb,
> - pdata->default_bpp);
> - if (!ret) {
> - dev_err(dev, "no suitable video mode found\n");
> - goto stop_clk;
> - }
> + modelist = list_first_entry(&info->modelist,
> + struct fb_modelist, list);
> + fb_videomode_to_var(&info->var, &modelist->mode);
>
> + atmel_lcdfb_check_var(&info->var, info);
>
> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> if (!regs) {
> @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> goto unregister_irqs;
> }
>
> - /*
> - * This makes sure that our colour bitfield
> - * descriptors are correctly initialised.
> - */
> - atmel_lcdfb_check_var(&info->var, info);
> -
> - ret = fb_set_var(info, &info->var);
> - if (ret) {
> - dev_warn(dev, "unable to set display parameters\n");
> - goto free_cmap;
> - }
> -
> dev_set_drvdata(dev, info);
>
> /*
> @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> goto reset_drvdata;
> }
>
> - /* add selected videomode to modelist */
> - fb_var_to_videomode(&fbmode, &info->var);
> - fb_add_videomode(&fbmode, &info->modelist);
> -
> /* Power up the LCDC screen */
> atmel_lcdfb_power_control(sinfo, 1);
>
> @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>
> reset_drvdata:
> dev_set_drvdata(dev, NULL);
> -free_cmap:
> fb_dealloc_cmap(&info->cmap);
> unregister_irqs:
> cancel_work_sync(&sinfo->task);
> @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
> .driver = {
> .name = "atmel_lcdfb",
> .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
> },
> };
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-16 13:42 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 13:42 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> get display timings from device tree
> Use videomode helpers to get display timings and configurations from
> device tree
2 sentences? Simply elaborate the 2nd one and it will be good.
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> drivers/video/Kconfig | 2 +
> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> 3 files changed, 289 insertions(+), 32 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> new file mode 100644
> index 0000000..1ec175e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
is even more self-explanatory...
> @@ -0,0 +1,75 @@
> +Atmel LCDC Framebuffer
> +-----------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + "atmel,at91sam9261-lcdc" ,
> + "atmel,at91sam9263-lcdc" ,
> + "atmel,at91sam9g10-lcdc" ,
> + "atmel,at91sam9g45-lcdc" ,
> + "atmel,at91sam9g45es-lcdc" ,
> + "atmel,at91sam9rl-lcdc" ,
> + "atmel,at32ap-lcdc"
> +- reg : Should contain 1 register ranges(address and length)
> +- interrupts : framebuffer controller interrupt
> +- display: a phandle pointing to the display node
> +
> +Required nodes:
> +- display: a display node is required to initialize the lcd panel
> + This should be in the board dts.
> +- default-mode: a videomode within the display with timing parameters
> + as specified below.
> +
> +Example:
> +
> + fb0: fb@0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + display = <&display0>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + };
> +
> +Atmel LCDC Display
> +-----------------------------------------------------
> +Required properties (as per of_videomode_helper):
Can you please point somewhere to the documentation:
Documentation/devicetree/bindings/video/display-timing.txt
> + - atmel,dmacon: dma controler configuration
Typo: controller.
> + - atmel,lcdcon2: lcd controler configuration
Ditto
> + - atmel,guard-time: lcd guard time (Delay in frame periods)
periods -> period, no?
> + - bits-per-pixel: lcd panel bit-depth.
> +
> +Optional properties (as per of_videomode_helper):
> + - atmel,lcdcon-backlight: enable backlight
> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
Is it a sting, or a number (as seen below)? If it is a number, please
tell how to choose the index.
> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
> +
> +Example:
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 4c1546f..0687482 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1018,6 +1018,8 @@ config FB_ATMEL
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select FB_MODE_HELPERS
> + select OF_VIDEOMODE
> help
> This enables support for the AT91/AT32 LCD Controller.
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index f67e226..4a31570 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,7 +20,11 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <video/of_display_timing.h>
As said in patch 1/8, this one belongs to this 4/8 patch.
> +#include <video/videomode.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> struct atmel_lcdfb_config *config;
> };
>
> +struct atmel_lcdfb_power_ctrl_gpio {
> + int gpio;
> + int active_low;
> +
> + struct list_head list;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> clk_disable(sinfo->lcdc_clk);
> }
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> +
> +static const char *atmel_lcdfb_wiring_modes[] = {
> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> +};
> +
> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> +{
> + const char *mode;
> + int err, i;
> +
> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> + if (err < 0)
> + return ATMEL_LCDC_WIRING_BGR;
> +
> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> + return i;
> +
> + return -ENODEV;
> +}
> +
> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> +{
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> +
> + list_for_each_entry(og, &pdata->pwr_gpios, list)
> + gpio_set_value(og->gpio, on);
> +}
> +
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + struct fb_info *info = sinfo->info;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> + struct fb_var_screeninfo *var = &info->var;
> + struct device *dev = &sinfo->pdev->dev;
> + struct device_node *np Þv->of_node;
> + struct device_node *display_np;
> + struct device_node *timings_np;
> + struct display_timings *timings;
> + enum of_gpio_flags flags;
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> + bool is_gpio_power = false;
> + int ret = -ENOENT;
> + int i, gpio;
> +
> + sinfo->config = (struct atmel_lcdfb_config*)
> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
Please split it in 2 steps, otherwise the day that the drivers doesn't
find the device in dt_ids table, it hangs here with an Oops.
> +
> + display_np = of_parse_phandle(np, "display", 0);
> + if (!display_np) {
> + dev_err(dev, "failed to find display phandle\n");
> + return -ENOENT;
> + }
> +
> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,guard-time\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
No, wrong error message.
> + goto put_display_node;
> + }
> +
> + ret = -ENOMEM;
> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> + i, &flags);
> + if (gpio < 0)
> + continue;
> +
> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> + if (!og)
> + goto put_display_node;
> +
> + og->gpio = gpio;
> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> + is_gpio_power = true;
> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> + if (ret) {
> + dev_err(dev, "request gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> +
> + ret = gpio_direction_output(gpio, og->active_low);
> + if (ret) {
> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> + }
> +
> + if (is_gpio_power)
> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> +
> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> + if (ret < 0) {
> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> + goto put_display_node;
> + }
> + pdata->lcd_wiring_mode = ret;
> +
> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
> +
> + timings = of_get_display_timings(display_np);
> + if (!timings) {
> + dev_err(dev, "failed to get display timings\n");
> + goto put_display_node;
> + }
> +
> + timings_np = of_find_node_by_name(display_np, "display-timings");
> + if (!timings_np) {
> + dev_err(dev, "failed to find display-timings node\n");
> + goto put_display_node;
> + }
> +
> + for (i = 0; i < of_get_child_count(timings_np); i++) {
> + struct videomode vm;
> + struct fb_videomode fb_vm;
> +
> + ret = videomode_from_timing(timings, &vm, i);
> + if (ret < 0)
> + goto put_timings_node;
> + ret = fb_videomode_from_videomode(&vm, &fb_vm);
> + if (ret < 0)
> + goto put_timings_node;
> +
> + fb_add_videomode(&fb_vm, &info->modelist);
> + }
> +
> + return 0;
> +
> +put_timings_node:
> + of_node_put(timings_np);
> +put_display_node:
> + of_node_put(display_np);
> + return ret;
> +}
> +#else
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + return 0;
> +}
> +#endif
>
> static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> struct fb_info *info;
> struct atmel_lcdfb_info *sinfo;
> - struct atmel_lcdfb_pdata *pdata;
> - struct fb_videomode fbmode;
> + struct atmel_lcdfb_pdata *pdata = NULL;
> struct resource *regs = NULL;
> struct resource *map = NULL;
> + struct fb_modelist *modelist;
> int ret;
>
> dev_dbg(dev, "%s BEGIN\n", __func__);
> @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> }
>
> sinfo = info->par;
> + sinfo->pdev = pdev;
> + sinfo->info = info;
> +
> + INIT_LIST_HEAD(&info->modelist);
>
> - if (dev->platform_data) {
> - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> + if (pdev->dev.of_node) {
> + ret = atmel_lcdfb_of_init(sinfo);
> + if (ret)
> + goto free_info;
> + } else if (dev->platform_data) {
> + struct fb_monspecs *monspecs;
> + int i;
> +
> + pdata = dev->platform_data;
> + monspecs = pdata->default_monspecs;
> sinfo->pdata = *pdata;
> +
> + for (i = 0; i < monspecs->modedb_len; i++)
> + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
> +
> + sinfo->config = atmel_lcdfb_get_config(pdev);
> +
> + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> } else {
> dev_err(dev, "cannot get default configuration\n");
> goto free_info;
> }
> - sinfo->info = info;
> - sinfo->pdev = pdev;
> - sinfo->config = atmel_lcdfb_get_config(pdev);
> +
> if (!sinfo->config)
> goto free_info;
>
> @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> info->pseudo_palette = sinfo->pseudo_palette;
> info->fbops = &atmel_lcdfb_ops;
>
> - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> info->fix = atmel_lcdfb_fix;
>
> /* Enable LCDC Clocks */
> @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> }
> atmel_lcdfb_start_clock(sinfo);
>
> - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> - info->monspecs.modedb_len, info->monspecs.modedb,
> - pdata->default_bpp);
> - if (!ret) {
> - dev_err(dev, "no suitable video mode found\n");
> - goto stop_clk;
> - }
> + modelist = list_first_entry(&info->modelist,
> + struct fb_modelist, list);
> + fb_videomode_to_var(&info->var, &modelist->mode);
>
> + atmel_lcdfb_check_var(&info->var, info);
>
> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> if (!regs) {
> @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> goto unregister_irqs;
> }
>
> - /*
> - * This makes sure that our colour bitfield
> - * descriptors are correctly initialised.
> - */
> - atmel_lcdfb_check_var(&info->var, info);
> -
> - ret = fb_set_var(info, &info->var);
> - if (ret) {
> - dev_warn(dev, "unable to set display parameters\n");
> - goto free_cmap;
> - }
> -
> dev_set_drvdata(dev, info);
>
> /*
> @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> goto reset_drvdata;
> }
>
> - /* add selected videomode to modelist */
> - fb_var_to_videomode(&fbmode, &info->var);
> - fb_add_videomode(&fbmode, &info->modelist);
> -
> /* Power up the LCDC screen */
> atmel_lcdfb_power_control(sinfo, 1);
>
> @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>
> reset_drvdata:
> dev_set_drvdata(dev, NULL);
> -free_cmap:
> fb_dealloc_cmap(&info->cmap);
> unregister_irqs:
> cancel_work_sync(&sinfo->task);
> @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
> .driver = {
> .name = "atmel_lcdfb",
> .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
> },
> };
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-16 13:42 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 13:42 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> get display timings from device tree
> Use videomode helpers to get display timings and configurations from
> device tree
2 sentences? Simply elaborate the 2nd one and it will be good.
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> drivers/video/Kconfig | 2 +
> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> 3 files changed, 289 insertions(+), 32 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> new file mode 100644
> index 0000000..1ec175e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
is even more self-explanatory...
> @@ -0,0 +1,75 @@
> +Atmel LCDC Framebuffer
> +-----------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + "atmel,at91sam9261-lcdc" ,
> + "atmel,at91sam9263-lcdc" ,
> + "atmel,at91sam9g10-lcdc" ,
> + "atmel,at91sam9g45-lcdc" ,
> + "atmel,at91sam9g45es-lcdc" ,
> + "atmel,at91sam9rl-lcdc" ,
> + "atmel,at32ap-lcdc"
> +- reg : Should contain 1 register ranges(address and length)
> +- interrupts : framebuffer controller interrupt
> +- display: a phandle pointing to the display node
> +
> +Required nodes:
> +- display: a display node is required to initialize the lcd panel
> + This should be in the board dts.
> +- default-mode: a videomode within the display with timing parameters
> + as specified below.
> +
> +Example:
> +
> + fb0: fb at 0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + display = <&display0>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + };
> +
> +Atmel LCDC Display
> +-----------------------------------------------------
> +Required properties (as per of_videomode_helper):
Can you please point somewhere to the documentation:
Documentation/devicetree/bindings/video/display-timing.txt
> + - atmel,dmacon: dma controler configuration
Typo: controller.
> + - atmel,lcdcon2: lcd controler configuration
Ditto
> + - atmel,guard-time: lcd guard time (Delay in frame periods)
periods -> period, no?
> + - bits-per-pixel: lcd panel bit-depth.
> +
> +Optional properties (as per of_videomode_helper):
> + - atmel,lcdcon-backlight: enable backlight
> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
Is it a sting, or a number (as seen below)? If it is a number, please
tell how to choose the index.
> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
> +
> +Example:
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 4c1546f..0687482 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1018,6 +1018,8 @@ config FB_ATMEL
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select FB_MODE_HELPERS
> + select OF_VIDEOMODE
> help
> This enables support for the AT91/AT32 LCD Controller.
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index f67e226..4a31570 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,7 +20,11 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <video/of_display_timing.h>
As said in patch 1/8, this one belongs to this 4/8 patch.
> +#include <video/videomode.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> struct atmel_lcdfb_config *config;
> };
>
> +struct atmel_lcdfb_power_ctrl_gpio {
> + int gpio;
> + int active_low;
> +
> + struct list_head list;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> clk_disable(sinfo->lcdc_clk);
> }
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> +
> +static const char *atmel_lcdfb_wiring_modes[] = {
> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> +};
> +
> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> +{
> + const char *mode;
> + int err, i;
> +
> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> + if (err < 0)
> + return ATMEL_LCDC_WIRING_BGR;
> +
> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> + return i;
> +
> + return -ENODEV;
> +}
> +
> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> +{
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> +
> + list_for_each_entry(og, &pdata->pwr_gpios, list)
> + gpio_set_value(og->gpio, on);
> +}
> +
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + struct fb_info *info = sinfo->info;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> + struct fb_var_screeninfo *var = &info->var;
> + struct device *dev = &sinfo->pdev->dev;
> + struct device_node *np =dev->of_node;
> + struct device_node *display_np;
> + struct device_node *timings_np;
> + struct display_timings *timings;
> + enum of_gpio_flags flags;
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> + bool is_gpio_power = false;
> + int ret = -ENOENT;
> + int i, gpio;
> +
> + sinfo->config = (struct atmel_lcdfb_config*)
> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
Please split it in 2 steps, otherwise the day that the drivers doesn't
find the device in dt_ids table, it hangs here with an Oops.
> +
> + display_np = of_parse_phandle(np, "display", 0);
> + if (!display_np) {
> + dev_err(dev, "failed to find display phandle\n");
> + return -ENOENT;
> + }
> +
> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,guard-time\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
No, wrong error message.
> + goto put_display_node;
> + }
> +
> + ret = -ENOMEM;
> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> + i, &flags);
> + if (gpio < 0)
> + continue;
> +
> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> + if (!og)
> + goto put_display_node;
> +
> + og->gpio = gpio;
> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> + is_gpio_power = true;
> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> + if (ret) {
> + dev_err(dev, "request gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> +
> + ret = gpio_direction_output(gpio, og->active_low);
> + if (ret) {
> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> + }
> +
> + if (is_gpio_power)
> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> +
> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> + if (ret < 0) {
> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> + goto put_display_node;
> + }
> + pdata->lcd_wiring_mode = ret;
> +
> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
> +
> + timings = of_get_display_timings(display_np);
> + if (!timings) {
> + dev_err(dev, "failed to get display timings\n");
> + goto put_display_node;
> + }
> +
> + timings_np = of_find_node_by_name(display_np, "display-timings");
> + if (!timings_np) {
> + dev_err(dev, "failed to find display-timings node\n");
> + goto put_display_node;
> + }
> +
> + for (i = 0; i < of_get_child_count(timings_np); i++) {
> + struct videomode vm;
> + struct fb_videomode fb_vm;
> +
> + ret = videomode_from_timing(timings, &vm, i);
> + if (ret < 0)
> + goto put_timings_node;
> + ret = fb_videomode_from_videomode(&vm, &fb_vm);
> + if (ret < 0)
> + goto put_timings_node;
> +
> + fb_add_videomode(&fb_vm, &info->modelist);
> + }
> +
> + return 0;
> +
> +put_timings_node:
> + of_node_put(timings_np);
> +put_display_node:
> + of_node_put(display_np);
> + return ret;
> +}
> +#else
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + return 0;
> +}
> +#endif
>
> static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> struct fb_info *info;
> struct atmel_lcdfb_info *sinfo;
> - struct atmel_lcdfb_pdata *pdata;
> - struct fb_videomode fbmode;
> + struct atmel_lcdfb_pdata *pdata = NULL;
> struct resource *regs = NULL;
> struct resource *map = NULL;
> + struct fb_modelist *modelist;
> int ret;
>
> dev_dbg(dev, "%s BEGIN\n", __func__);
> @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> }
>
> sinfo = info->par;
> + sinfo->pdev = pdev;
> + sinfo->info = info;
> +
> + INIT_LIST_HEAD(&info->modelist);
>
> - if (dev->platform_data) {
> - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> + if (pdev->dev.of_node) {
> + ret = atmel_lcdfb_of_init(sinfo);
> + if (ret)
> + goto free_info;
> + } else if (dev->platform_data) {
> + struct fb_monspecs *monspecs;
> + int i;
> +
> + pdata = dev->platform_data;
> + monspecs = pdata->default_monspecs;
> sinfo->pdata = *pdata;
> +
> + for (i = 0; i < monspecs->modedb_len; i++)
> + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
> +
> + sinfo->config = atmel_lcdfb_get_config(pdev);
> +
> + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> } else {
> dev_err(dev, "cannot get default configuration\n");
> goto free_info;
> }
> - sinfo->info = info;
> - sinfo->pdev = pdev;
> - sinfo->config = atmel_lcdfb_get_config(pdev);
> +
> if (!sinfo->config)
> goto free_info;
>
> @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> info->pseudo_palette = sinfo->pseudo_palette;
> info->fbops = &atmel_lcdfb_ops;
>
> - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> info->fix = atmel_lcdfb_fix;
>
> /* Enable LCDC Clocks */
> @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> }
> atmel_lcdfb_start_clock(sinfo);
>
> - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> - info->monspecs.modedb_len, info->monspecs.modedb,
> - pdata->default_bpp);
> - if (!ret) {
> - dev_err(dev, "no suitable video mode found\n");
> - goto stop_clk;
> - }
> + modelist = list_first_entry(&info->modelist,
> + struct fb_modelist, list);
> + fb_videomode_to_var(&info->var, &modelist->mode);
>
> + atmel_lcdfb_check_var(&info->var, info);
>
> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> if (!regs) {
> @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> goto unregister_irqs;
> }
>
> - /*
> - * This makes sure that our colour bitfield
> - * descriptors are correctly initialised.
> - */
> - atmel_lcdfb_check_var(&info->var, info);
> -
> - ret = fb_set_var(info, &info->var);
> - if (ret) {
> - dev_warn(dev, "unable to set display parameters\n");
> - goto free_cmap;
> - }
> -
> dev_set_drvdata(dev, info);
>
> /*
> @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> goto reset_drvdata;
> }
>
> - /* add selected videomode to modelist */
> - fb_var_to_videomode(&fbmode, &info->var);
> - fb_add_videomode(&fbmode, &info->modelist);
> -
> /* Power up the LCDC screen */
> atmel_lcdfb_power_control(sinfo, 1);
>
> @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>
> reset_drvdata:
> dev_set_drvdata(dev, NULL);
> -free_cmap:
> fb_dealloc_cmap(&info->cmap);
> unregister_irqs:
> cancel_work_sync(&sinfo->task);
> @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
> .driver = {
> .name = "atmel_lcdfb",
> .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
> },
> };
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
2013-04-16 13:42 ` Nicolas Ferre
(?)
@ 2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 13:44 UTC (permalink / raw)
To: Nicolas Ferre
Cc: Andrew Morton, devicetree-discuss, linux-fbdev, linux-arm-kernel
On 15:42 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > get display timings from device tree
> > Use videomode helpers to get display timings and configurations from
> > device tree
>
> 2 sentences? Simply elaborate the 2nd one and it will be good.
>
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: linux-fbdev@vger.kernel.org
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Andrew Morton <akpm@linux-foundation.org>
> > ---
> > .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> > drivers/video/Kconfig | 2 +
> > drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> > 3 files changed, 289 insertions(+), 32 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
> >
> > diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> > new file mode 100644
> > index 0000000..1ec175e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
> is even more self-explanatory...
we do not describe drivers but IP
>
> > @@ -0,0 +1,75 @@
> > +Atmel LCDC Framebuffer
> > +-----------------------------------------------------
> > +
> > +Required properties:
> > +- compatible :
> > + "atmel,at91sam9261-lcdc" ,
> > + "atmel,at91sam9263-lcdc" ,
> > + "atmel,at91sam9g10-lcdc" ,
> > + "atmel,at91sam9g45-lcdc" ,
> > + "atmel,at91sam9g45es-lcdc" ,
> > + "atmel,at91sam9rl-lcdc" ,
> > + "atmel,at32ap-lcdc"
> > +- reg : Should contain 1 register ranges(address and length)
> > +- interrupts : framebuffer controller interrupt
> > +- display: a phandle pointing to the display node
> > +
> > +Required nodes:
> > +- display: a display node is required to initialize the lcd panel
> > + This should be in the board dts.
> > +- default-mode: a videomode within the display with timing parameters
> > + as specified below.
> > +
> > +Example:
> > +
> > + fb0: fb@0x00500000 {
> > + compatible = "atmel,at91sam9g45-lcdc";
> > + reg = <0x00500000 0x1000>;
> > + interrupts = <23 3 0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fb>;
> > + display = <&display0>;
> > + status = "okay";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + };
> > +
> > +Atmel LCDC Display
> > +-----------------------------------------------------
> > +Required properties (as per of_videomode_helper):
>
> Can you please point somewhere to the documentation:
> Documentation/devicetree/bindings/video/display-timing.txt
>
> > + - atmel,dmacon: dma controler configuration
>
> Typo: controller.
>
> > + - atmel,lcdcon2: lcd controler configuration
>
> Ditto
>
> > + - atmel,guard-time: lcd guard time (Delay in frame periods)
>
> periods -> period, no?
no it's periods even in the datasheet
>
> > + - bits-per-pixel: lcd panel bit-depth.
> > +
> > +Optional properties (as per of_videomode_helper):
> > + - atmel,lcdcon-backlight: enable backlight
> > + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
>
> Is it a sting, or a number (as seen below)? If it is a number, please
> tell how to choose the index.
String
>
>
> > + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
> > +
> > +Example:
> > + display0: display {
> > + bits-per-pixel = <32>;
> > + atmel,lcdcon-backlight;
> > + atmel,dmacon = <0x1>;
> > + atmel,lcdcon2 = <0x80008002>;
> > + atmel,guard-time = <9>;
> > + atmel,lcd-wiring-mode = <1>;
> > +
> > + display-timings {
> > + native-mode = <&timing0>;
> > + timing0: timing0 {
> > + clock-frequency = <9000000>;
> > + hactive = <480>;
> > + vactive = <272>;
> > + hback-porch = <1>;
> > + hfront-porch = <1>;
> > + vback-porch = <40>;
> > + vfront-porch = <1>;
> > + hsync-len = <45>;
> > + vsync-len = <1>;
> > + };
> > + };
> > + };
> > diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> > index 4c1546f..0687482 100644
> > --- a/drivers/video/Kconfig
> > +++ b/drivers/video/Kconfig
> > @@ -1018,6 +1018,8 @@ config FB_ATMEL
> > select FB_CFB_FILLRECT
> > select FB_CFB_COPYAREA
> > select FB_CFB_IMAGEBLIT
> > + select FB_MODE_HELPERS
> > + select OF_VIDEOMODE
> > help
> > This enables support for the AT91/AT32 LCD Controller.
> >
> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> > index f67e226..4a31570 100644
> > --- a/drivers/video/atmel_lcdfb.c
> > +++ b/drivers/video/atmel_lcdfb.c
> > @@ -20,7 +20,11 @@
> > #include <linux/gfp.h>
> > #include <linux/module.h>
> > #include <linux/platform_data/atmel.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_gpio.h>
> > #include <video/of_display_timing.h>
>
> As said in patch 1/8, this one belongs to this 4/8 patch.
>
> > +#include <video/videomode.h>
> >
> > #include <mach/cpu.h>
> > #include <asm/gpio.h>
> > @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> > struct atmel_lcdfb_config *config;
> > };
> >
> > +struct atmel_lcdfb_power_ctrl_gpio {
> > + int gpio;
> > + int active_low;
> > +
> > + struct list_head list;
> > +};
> > +
> > #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> > #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
> >
> > @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> > clk_disable(sinfo->lcdc_clk);
> > }
> >
> > +#ifdef CONFIG_OF
> > +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> > + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> > + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> > + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> > + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> > + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> > + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> > + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> > + { /* sentinel */ }
> > +};
> > +
> > +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> > +
> > +static const char *atmel_lcdfb_wiring_modes[] = {
> > + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> > + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> > +};
> > +
> > +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> > +{
> > + const char *mode;
> > + int err, i;
> > +
> > + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> > + if (err < 0)
> > + return ATMEL_LCDC_WIRING_BGR;
> > +
> > + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> > + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> > + return i;
> > +
> > + return -ENODEV;
> > +}
> > +
> > +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> > +{
> > + struct atmel_lcdfb_power_ctrl_gpio *og;
> > +
> > + list_for_each_entry(og, &pdata->pwr_gpios, list)
> > + gpio_set_value(og->gpio, on);
> > +}
> > +
> > +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> > +{
> > + struct fb_info *info = sinfo->info;
> > + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> > + struct fb_var_screeninfo *var = &info->var;
> > + struct device *dev = &sinfo->pdev->dev;
> > + struct device_node *np =dev->of_node;
> > + struct device_node *display_np;
> > + struct device_node *timings_np;
> > + struct display_timings *timings;
> > + enum of_gpio_flags flags;
> > + struct atmel_lcdfb_power_ctrl_gpio *og;
> > + bool is_gpio_power = false;
> > + int ret = -ENOENT;
> > + int i, gpio;
> > +
> > + sinfo->config = (struct atmel_lcdfb_config*)
> > + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
>
> Please split it in 2 steps, otherwise the day that the drivers doesn't
> find the device in dt_ids table, it hangs here with an Oops.
no as you will never end here in this case
>
> > +
> > + display_np = of_parse_phandle(np, "display", 0);
> > + if (!display_np) {
> > + dev_err(dev, "failed to find display phandle\n");
> > + return -ENOENT;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property bits-per-pixel\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property atmel,guard-time\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property bits-per-pixel\n");
>
> No, wrong error message.
>
> > + goto put_display_node;
> > + }
> > +
> > + ret = -ENOMEM;
> > + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> > + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> > + i, &flags);
> > + if (gpio < 0)
> > + continue;
> > +
> > + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> > + if (!og)
> > + goto put_display_node;
> > +
> > + og->gpio = gpio;
> > + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> > + is_gpio_power = true;
> > + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> > + if (ret) {
> > + dev_err(dev, "request gpio %d failed\n", gpio);
> > + goto put_display_node;
> > + }
> > +
> > + ret = gpio_direction_output(gpio, og->active_low);
> > + if (ret) {
> > + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> > + goto put_display_node;
> > + }
> > + }
> > +
> > + if (is_gpio_power)
> > + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> > +
> > + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> > + if (ret < 0) {
> > + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> > + goto put_display_node;
> > + }
> > + pdata->lcd_wiring_mode = ret;
> > +
> > + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
> > +
> > + timings = of_get_display_timings(display_np);
> > + if (!timings) {
> > + dev_err(dev, "failed to get display timings\n");
> > + goto put_display_node;
> > + }
> > +
> > + timings_np = of_find_node_by_name(display_np, "display-timings");
> > + if (!timings_np) {
> > + dev_err(dev, "failed to find display-timings node\n");
> > + goto put_display_node;
> > + }
> > +
> > + for (i = 0; i < of_get_child_count(timings_np); i++) {
> > + struct videomode vm;
> > + struct fb_videomode fb_vm;
> > +
> > + ret = videomode_from_timing(timings, &vm, i);
> > + if (ret < 0)
> > + goto put_timings_node;
> > + ret = fb_videomode_from_videomode(&vm, &fb_vm);
> > + if (ret < 0)
> > + goto put_timings_node;
> > +
> > + fb_add_videomode(&fb_vm, &info->modelist);
> > + }
> > +
> > + return 0;
> > +
> > +put_timings_node:
> > + of_node_put(timings_np);
> > +put_display_node:
> > + of_node_put(display_np);
> > + return ret;
> > +}
> > +#else
> > +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> > +{
> > + return 0;
> > +}
> > +#endif
> >
> > static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > {
> > struct device *dev = &pdev->dev;
> > struct fb_info *info;
> > struct atmel_lcdfb_info *sinfo;
> > - struct atmel_lcdfb_pdata *pdata;
> > - struct fb_videomode fbmode;
> > + struct atmel_lcdfb_pdata *pdata = NULL;
> > struct resource *regs = NULL;
> > struct resource *map = NULL;
> > + struct fb_modelist *modelist;
> > int ret;
> >
> > dev_dbg(dev, "%s BEGIN\n", __func__);
> > @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > }
> >
> > sinfo = info->par;
> > + sinfo->pdev = pdev;
> > + sinfo->info = info;
> > +
> > + INIT_LIST_HEAD(&info->modelist);
> >
> > - if (dev->platform_data) {
> > - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> > + if (pdev->dev.of_node) {
> > + ret = atmel_lcdfb_of_init(sinfo);
> > + if (ret)
> > + goto free_info;
> > + } else if (dev->platform_data) {
> > + struct fb_monspecs *monspecs;
> > + int i;
> > +
> > + pdata = dev->platform_data;
> > + monspecs = pdata->default_monspecs;
> > sinfo->pdata = *pdata;
> > +
> > + for (i = 0; i < monspecs->modedb_len; i++)
> > + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
> > +
> > + sinfo->config = atmel_lcdfb_get_config(pdev);
> > +
> > + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
> > + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> > } else {
> > dev_err(dev, "cannot get default configuration\n");
> > goto free_info;
> > }
> > - sinfo->info = info;
> > - sinfo->pdev = pdev;
> > - sinfo->config = atmel_lcdfb_get_config(pdev);
> > +
> > if (!sinfo->config)
> > goto free_info;
> >
> > @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > info->pseudo_palette = sinfo->pseudo_palette;
> > info->fbops = &atmel_lcdfb_ops;
> >
> > - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> > info->fix = atmel_lcdfb_fix;
> >
> > /* Enable LCDC Clocks */
> > @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > }
> > atmel_lcdfb_start_clock(sinfo);
> >
> > - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> > - info->monspecs.modedb_len, info->monspecs.modedb,
> > - pdata->default_bpp);
> > - if (!ret) {
> > - dev_err(dev, "no suitable video mode found\n");
> > - goto stop_clk;
> > - }
> > + modelist = list_first_entry(&info->modelist,
> > + struct fb_modelist, list);
> > + fb_videomode_to_var(&info->var, &modelist->mode);
> >
> > + atmel_lcdfb_check_var(&info->var, info);
> >
> > regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > if (!regs) {
> > @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > goto unregister_irqs;
> > }
> >
> > - /*
> > - * This makes sure that our colour bitfield
> > - * descriptors are correctly initialised.
> > - */
> > - atmel_lcdfb_check_var(&info->var, info);
> > -
> > - ret = fb_set_var(info, &info->var);
> > - if (ret) {
> > - dev_warn(dev, "unable to set display parameters\n");
> > - goto free_cmap;
> > - }
> > -
> > dev_set_drvdata(dev, info);
> >
> > /*
> > @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > goto reset_drvdata;
> > }
> >
> > - /* add selected videomode to modelist */
> > - fb_var_to_videomode(&fbmode, &info->var);
> > - fb_add_videomode(&fbmode, &info->modelist);
> > -
> > /* Power up the LCDC screen */
> > atmel_lcdfb_power_control(sinfo, 1);
> >
> > @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> >
> > reset_drvdata:
> > dev_set_drvdata(dev, NULL);
> > -free_cmap:
> > fb_dealloc_cmap(&info->cmap);
> > unregister_irqs:
> > cancel_work_sync(&sinfo->task);
> > @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
> > .driver = {
> > .name = "atmel_lcdfb",
> > .owner = THIS_MODULE,
> > + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
> > },
> > };
> >
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 13:44 UTC (permalink / raw)
To: linux-arm-kernel
On 15:42 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > get display timings from device tree
> > Use videomode helpers to get display timings and configurations from
> > device tree
>
> 2 sentences? Simply elaborate the 2nd one and it will be good.
>
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: linux-fbdev@vger.kernel.org
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Andrew Morton <akpm@linux-foundation.org>
> > ---
> > .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> > drivers/video/Kconfig | 2 +
> > drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> > 3 files changed, 289 insertions(+), 32 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
> >
> > diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> > new file mode 100644
> > index 0000000..1ec175e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
> is even more self-explanatory...
we do not describe drivers but IP
>
> > @@ -0,0 +1,75 @@
> > +Atmel LCDC Framebuffer
> > +-----------------------------------------------------
> > +
> > +Required properties:
> > +- compatible :
> > + "atmel,at91sam9261-lcdc" ,
> > + "atmel,at91sam9263-lcdc" ,
> > + "atmel,at91sam9g10-lcdc" ,
> > + "atmel,at91sam9g45-lcdc" ,
> > + "atmel,at91sam9g45es-lcdc" ,
> > + "atmel,at91sam9rl-lcdc" ,
> > + "atmel,at32ap-lcdc"
> > +- reg : Should contain 1 register ranges(address and length)
> > +- interrupts : framebuffer controller interrupt
> > +- display: a phandle pointing to the display node
> > +
> > +Required nodes:
> > +- display: a display node is required to initialize the lcd panel
> > + This should be in the board dts.
> > +- default-mode: a videomode within the display with timing parameters
> > + as specified below.
> > +
> > +Example:
> > +
> > + fb0: fb@0x00500000 {
> > + compatible = "atmel,at91sam9g45-lcdc";
> > + reg = <0x00500000 0x1000>;
> > + interrupts = <23 3 0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fb>;
> > + display = <&display0>;
> > + status = "okay";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + };
> > +
> > +Atmel LCDC Display
> > +-----------------------------------------------------
> > +Required properties (as per of_videomode_helper):
>
> Can you please point somewhere to the documentation:
> Documentation/devicetree/bindings/video/display-timing.txt
>
> > + - atmel,dmacon: dma controler configuration
>
> Typo: controller.
>
> > + - atmel,lcdcon2: lcd controler configuration
>
> Ditto
>
> > + - atmel,guard-time: lcd guard time (Delay in frame periods)
>
> periods -> period, no?
no it's periods even in the datasheet
>
> > + - bits-per-pixel: lcd panel bit-depth.
> > +
> > +Optional properties (as per of_videomode_helper):
> > + - atmel,lcdcon-backlight: enable backlight
> > + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
>
> Is it a sting, or a number (as seen below)? If it is a number, please
> tell how to choose the index.
String
>
>
> > + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
> > +
> > +Example:
> > + display0: display {
> > + bits-per-pixel = <32>;
> > + atmel,lcdcon-backlight;
> > + atmel,dmacon = <0x1>;
> > + atmel,lcdcon2 = <0x80008002>;
> > + atmel,guard-time = <9>;
> > + atmel,lcd-wiring-mode = <1>;
> > +
> > + display-timings {
> > + native-mode = <&timing0>;
> > + timing0: timing0 {
> > + clock-frequency = <9000000>;
> > + hactive = <480>;
> > + vactive = <272>;
> > + hback-porch = <1>;
> > + hfront-porch = <1>;
> > + vback-porch = <40>;
> > + vfront-porch = <1>;
> > + hsync-len = <45>;
> > + vsync-len = <1>;
> > + };
> > + };
> > + };
> > diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> > index 4c1546f..0687482 100644
> > --- a/drivers/video/Kconfig
> > +++ b/drivers/video/Kconfig
> > @@ -1018,6 +1018,8 @@ config FB_ATMEL
> > select FB_CFB_FILLRECT
> > select FB_CFB_COPYAREA
> > select FB_CFB_IMAGEBLIT
> > + select FB_MODE_HELPERS
> > + select OF_VIDEOMODE
> > help
> > This enables support for the AT91/AT32 LCD Controller.
> >
> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> > index f67e226..4a31570 100644
> > --- a/drivers/video/atmel_lcdfb.c
> > +++ b/drivers/video/atmel_lcdfb.c
> > @@ -20,7 +20,11 @@
> > #include <linux/gfp.h>
> > #include <linux/module.h>
> > #include <linux/platform_data/atmel.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_gpio.h>
> > #include <video/of_display_timing.h>
>
> As said in patch 1/8, this one belongs to this 4/8 patch.
>
> > +#include <video/videomode.h>
> >
> > #include <mach/cpu.h>
> > #include <asm/gpio.h>
> > @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> > struct atmel_lcdfb_config *config;
> > };
> >
> > +struct atmel_lcdfb_power_ctrl_gpio {
> > + int gpio;
> > + int active_low;
> > +
> > + struct list_head list;
> > +};
> > +
> > #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> > #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
> >
> > @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> > clk_disable(sinfo->lcdc_clk);
> > }
> >
> > +#ifdef CONFIG_OF
> > +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> > + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> > + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> > + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> > + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> > + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> > + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> > + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> > + { /* sentinel */ }
> > +};
> > +
> > +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> > +
> > +static const char *atmel_lcdfb_wiring_modes[] = {
> > + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> > + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> > +};
> > +
> > +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> > +{
> > + const char *mode;
> > + int err, i;
> > +
> > + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> > + if (err < 0)
> > + return ATMEL_LCDC_WIRING_BGR;
> > +
> > + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> > + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> > + return i;
> > +
> > + return -ENODEV;
> > +}
> > +
> > +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> > +{
> > + struct atmel_lcdfb_power_ctrl_gpio *og;
> > +
> > + list_for_each_entry(og, &pdata->pwr_gpios, list)
> > + gpio_set_value(og->gpio, on);
> > +}
> > +
> > +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> > +{
> > + struct fb_info *info = sinfo->info;
> > + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> > + struct fb_var_screeninfo *var = &info->var;
> > + struct device *dev = &sinfo->pdev->dev;
> > + struct device_node *np Þv->of_node;
> > + struct device_node *display_np;
> > + struct device_node *timings_np;
> > + struct display_timings *timings;
> > + enum of_gpio_flags flags;
> > + struct atmel_lcdfb_power_ctrl_gpio *og;
> > + bool is_gpio_power = false;
> > + int ret = -ENOENT;
> > + int i, gpio;
> > +
> > + sinfo->config = (struct atmel_lcdfb_config*)
> > + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
>
> Please split it in 2 steps, otherwise the day that the drivers doesn't
> find the device in dt_ids table, it hangs here with an Oops.
no as you will never end here in this case
>
> > +
> > + display_np = of_parse_phandle(np, "display", 0);
> > + if (!display_np) {
> > + dev_err(dev, "failed to find display phandle\n");
> > + return -ENOENT;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property bits-per-pixel\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property atmel,guard-time\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property bits-per-pixel\n");
>
> No, wrong error message.
>
> > + goto put_display_node;
> > + }
> > +
> > + ret = -ENOMEM;
> > + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> > + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> > + i, &flags);
> > + if (gpio < 0)
> > + continue;
> > +
> > + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> > + if (!og)
> > + goto put_display_node;
> > +
> > + og->gpio = gpio;
> > + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> > + is_gpio_power = true;
> > + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> > + if (ret) {
> > + dev_err(dev, "request gpio %d failed\n", gpio);
> > + goto put_display_node;
> > + }
> > +
> > + ret = gpio_direction_output(gpio, og->active_low);
> > + if (ret) {
> > + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> > + goto put_display_node;
> > + }
> > + }
> > +
> > + if (is_gpio_power)
> > + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> > +
> > + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> > + if (ret < 0) {
> > + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> > + goto put_display_node;
> > + }
> > + pdata->lcd_wiring_mode = ret;
> > +
> > + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
> > +
> > + timings = of_get_display_timings(display_np);
> > + if (!timings) {
> > + dev_err(dev, "failed to get display timings\n");
> > + goto put_display_node;
> > + }
> > +
> > + timings_np = of_find_node_by_name(display_np, "display-timings");
> > + if (!timings_np) {
> > + dev_err(dev, "failed to find display-timings node\n");
> > + goto put_display_node;
> > + }
> > +
> > + for (i = 0; i < of_get_child_count(timings_np); i++) {
> > + struct videomode vm;
> > + struct fb_videomode fb_vm;
> > +
> > + ret = videomode_from_timing(timings, &vm, i);
> > + if (ret < 0)
> > + goto put_timings_node;
> > + ret = fb_videomode_from_videomode(&vm, &fb_vm);
> > + if (ret < 0)
> > + goto put_timings_node;
> > +
> > + fb_add_videomode(&fb_vm, &info->modelist);
> > + }
> > +
> > + return 0;
> > +
> > +put_timings_node:
> > + of_node_put(timings_np);
> > +put_display_node:
> > + of_node_put(display_np);
> > + return ret;
> > +}
> > +#else
> > +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> > +{
> > + return 0;
> > +}
> > +#endif
> >
> > static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > {
> > struct device *dev = &pdev->dev;
> > struct fb_info *info;
> > struct atmel_lcdfb_info *sinfo;
> > - struct atmel_lcdfb_pdata *pdata;
> > - struct fb_videomode fbmode;
> > + struct atmel_lcdfb_pdata *pdata = NULL;
> > struct resource *regs = NULL;
> > struct resource *map = NULL;
> > + struct fb_modelist *modelist;
> > int ret;
> >
> > dev_dbg(dev, "%s BEGIN\n", __func__);
> > @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > }
> >
> > sinfo = info->par;
> > + sinfo->pdev = pdev;
> > + sinfo->info = info;
> > +
> > + INIT_LIST_HEAD(&info->modelist);
> >
> > - if (dev->platform_data) {
> > - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> > + if (pdev->dev.of_node) {
> > + ret = atmel_lcdfb_of_init(sinfo);
> > + if (ret)
> > + goto free_info;
> > + } else if (dev->platform_data) {
> > + struct fb_monspecs *monspecs;
> > + int i;
> > +
> > + pdata = dev->platform_data;
> > + monspecs = pdata->default_monspecs;
> > sinfo->pdata = *pdata;
> > +
> > + for (i = 0; i < monspecs->modedb_len; i++)
> > + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
> > +
> > + sinfo->config = atmel_lcdfb_get_config(pdev);
> > +
> > + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
> > + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> > } else {
> > dev_err(dev, "cannot get default configuration\n");
> > goto free_info;
> > }
> > - sinfo->info = info;
> > - sinfo->pdev = pdev;
> > - sinfo->config = atmel_lcdfb_get_config(pdev);
> > +
> > if (!sinfo->config)
> > goto free_info;
> >
> > @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > info->pseudo_palette = sinfo->pseudo_palette;
> > info->fbops = &atmel_lcdfb_ops;
> >
> > - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> > info->fix = atmel_lcdfb_fix;
> >
> > /* Enable LCDC Clocks */
> > @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > }
> > atmel_lcdfb_start_clock(sinfo);
> >
> > - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> > - info->monspecs.modedb_len, info->monspecs.modedb,
> > - pdata->default_bpp);
> > - if (!ret) {
> > - dev_err(dev, "no suitable video mode found\n");
> > - goto stop_clk;
> > - }
> > + modelist = list_first_entry(&info->modelist,
> > + struct fb_modelist, list);
> > + fb_videomode_to_var(&info->var, &modelist->mode);
> >
> > + atmel_lcdfb_check_var(&info->var, info);
> >
> > regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > if (!regs) {
> > @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > goto unregister_irqs;
> > }
> >
> > - /*
> > - * This makes sure that our colour bitfield
> > - * descriptors are correctly initialised.
> > - */
> > - atmel_lcdfb_check_var(&info->var, info);
> > -
> > - ret = fb_set_var(info, &info->var);
> > - if (ret) {
> > - dev_warn(dev, "unable to set display parameters\n");
> > - goto free_cmap;
> > - }
> > -
> > dev_set_drvdata(dev, info);
> >
> > /*
> > @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > goto reset_drvdata;
> > }
> >
> > - /* add selected videomode to modelist */
> > - fb_var_to_videomode(&fbmode, &info->var);
> > - fb_add_videomode(&fbmode, &info->modelist);
> > -
> > /* Power up the LCDC screen */
> > atmel_lcdfb_power_control(sinfo, 1);
> >
> > @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> >
> > reset_drvdata:
> > dev_set_drvdata(dev, NULL);
> > -free_cmap:
> > fb_dealloc_cmap(&info->cmap);
> > unregister_irqs:
> > cancel_work_sync(&sinfo->task);
> > @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
> > .driver = {
> > .name = "atmel_lcdfb",
> > .owner = THIS_MODULE,
> > + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
> > },
> > };
> >
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 13:44 UTC (permalink / raw)
To: linux-arm-kernel
On 15:42 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > get display timings from device tree
> > Use videomode helpers to get display timings and configurations from
> > device tree
>
> 2 sentences? Simply elaborate the 2nd one and it will be good.
>
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: linux-fbdev at vger.kernel.org
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Andrew Morton <akpm@linux-foundation.org>
> > ---
> > .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> > drivers/video/Kconfig | 2 +
> > drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> > 3 files changed, 289 insertions(+), 32 deletions(-)
> > create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
> >
> > diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> > new file mode 100644
> > index 0000000..1ec175e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
> is even more self-explanatory...
we do not describe drivers but IP
>
> > @@ -0,0 +1,75 @@
> > +Atmel LCDC Framebuffer
> > +-----------------------------------------------------
> > +
> > +Required properties:
> > +- compatible :
> > + "atmel,at91sam9261-lcdc" ,
> > + "atmel,at91sam9263-lcdc" ,
> > + "atmel,at91sam9g10-lcdc" ,
> > + "atmel,at91sam9g45-lcdc" ,
> > + "atmel,at91sam9g45es-lcdc" ,
> > + "atmel,at91sam9rl-lcdc" ,
> > + "atmel,at32ap-lcdc"
> > +- reg : Should contain 1 register ranges(address and length)
> > +- interrupts : framebuffer controller interrupt
> > +- display: a phandle pointing to the display node
> > +
> > +Required nodes:
> > +- display: a display node is required to initialize the lcd panel
> > + This should be in the board dts.
> > +- default-mode: a videomode within the display with timing parameters
> > + as specified below.
> > +
> > +Example:
> > +
> > + fb0: fb at 0x00500000 {
> > + compatible = "atmel,at91sam9g45-lcdc";
> > + reg = <0x00500000 0x1000>;
> > + interrupts = <23 3 0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fb>;
> > + display = <&display0>;
> > + status = "okay";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + };
> > +
> > +Atmel LCDC Display
> > +-----------------------------------------------------
> > +Required properties (as per of_videomode_helper):
>
> Can you please point somewhere to the documentation:
> Documentation/devicetree/bindings/video/display-timing.txt
>
> > + - atmel,dmacon: dma controler configuration
>
> Typo: controller.
>
> > + - atmel,lcdcon2: lcd controler configuration
>
> Ditto
>
> > + - atmel,guard-time: lcd guard time (Delay in frame periods)
>
> periods -> period, no?
no it's periods even in the datasheet
>
> > + - bits-per-pixel: lcd panel bit-depth.
> > +
> > +Optional properties (as per of_videomode_helper):
> > + - atmel,lcdcon-backlight: enable backlight
> > + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
>
> Is it a sting, or a number (as seen below)? If it is a number, please
> tell how to choose the index.
String
>
>
> > + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
> > +
> > +Example:
> > + display0: display {
> > + bits-per-pixel = <32>;
> > + atmel,lcdcon-backlight;
> > + atmel,dmacon = <0x1>;
> > + atmel,lcdcon2 = <0x80008002>;
> > + atmel,guard-time = <9>;
> > + atmel,lcd-wiring-mode = <1>;
> > +
> > + display-timings {
> > + native-mode = <&timing0>;
> > + timing0: timing0 {
> > + clock-frequency = <9000000>;
> > + hactive = <480>;
> > + vactive = <272>;
> > + hback-porch = <1>;
> > + hfront-porch = <1>;
> > + vback-porch = <40>;
> > + vfront-porch = <1>;
> > + hsync-len = <45>;
> > + vsync-len = <1>;
> > + };
> > + };
> > + };
> > diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> > index 4c1546f..0687482 100644
> > --- a/drivers/video/Kconfig
> > +++ b/drivers/video/Kconfig
> > @@ -1018,6 +1018,8 @@ config FB_ATMEL
> > select FB_CFB_FILLRECT
> > select FB_CFB_COPYAREA
> > select FB_CFB_IMAGEBLIT
> > + select FB_MODE_HELPERS
> > + select OF_VIDEOMODE
> > help
> > This enables support for the AT91/AT32 LCD Controller.
> >
> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> > index f67e226..4a31570 100644
> > --- a/drivers/video/atmel_lcdfb.c
> > +++ b/drivers/video/atmel_lcdfb.c
> > @@ -20,7 +20,11 @@
> > #include <linux/gfp.h>
> > #include <linux/module.h>
> > #include <linux/platform_data/atmel.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_gpio.h>
> > #include <video/of_display_timing.h>
>
> As said in patch 1/8, this one belongs to this 4/8 patch.
>
> > +#include <video/videomode.h>
> >
> > #include <mach/cpu.h>
> > #include <asm/gpio.h>
> > @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> > struct atmel_lcdfb_config *config;
> > };
> >
> > +struct atmel_lcdfb_power_ctrl_gpio {
> > + int gpio;
> > + int active_low;
> > +
> > + struct list_head list;
> > +};
> > +
> > #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> > #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
> >
> > @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> > clk_disable(sinfo->lcdc_clk);
> > }
> >
> > +#ifdef CONFIG_OF
> > +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> > + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> > + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> > + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> > + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> > + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> > + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> > + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> > + { /* sentinel */ }
> > +};
> > +
> > +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> > +
> > +static const char *atmel_lcdfb_wiring_modes[] = {
> > + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> > + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> > +};
> > +
> > +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> > +{
> > + const char *mode;
> > + int err, i;
> > +
> > + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> > + if (err < 0)
> > + return ATMEL_LCDC_WIRING_BGR;
> > +
> > + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> > + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> > + return i;
> > +
> > + return -ENODEV;
> > +}
> > +
> > +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> > +{
> > + struct atmel_lcdfb_power_ctrl_gpio *og;
> > +
> > + list_for_each_entry(og, &pdata->pwr_gpios, list)
> > + gpio_set_value(og->gpio, on);
> > +}
> > +
> > +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> > +{
> > + struct fb_info *info = sinfo->info;
> > + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> > + struct fb_var_screeninfo *var = &info->var;
> > + struct device *dev = &sinfo->pdev->dev;
> > + struct device_node *np =dev->of_node;
> > + struct device_node *display_np;
> > + struct device_node *timings_np;
> > + struct display_timings *timings;
> > + enum of_gpio_flags flags;
> > + struct atmel_lcdfb_power_ctrl_gpio *og;
> > + bool is_gpio_power = false;
> > + int ret = -ENOENT;
> > + int i, gpio;
> > +
> > + sinfo->config = (struct atmel_lcdfb_config*)
> > + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
>
> Please split it in 2 steps, otherwise the day that the drivers doesn't
> find the device in dt_ids table, it hangs here with an Oops.
no as you will never end here in this case
>
> > +
> > + display_np = of_parse_phandle(np, "display", 0);
> > + if (!display_np) {
> > + dev_err(dev, "failed to find display phandle\n");
> > + return -ENOENT;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property bits-per-pixel\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property atmel,guard-time\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> > + goto put_display_node;
> > + }
> > +
> > + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get property bits-per-pixel\n");
>
> No, wrong error message.
>
> > + goto put_display_node;
> > + }
> > +
> > + ret = -ENOMEM;
> > + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> > + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> > + i, &flags);
> > + if (gpio < 0)
> > + continue;
> > +
> > + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> > + if (!og)
> > + goto put_display_node;
> > +
> > + og->gpio = gpio;
> > + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> > + is_gpio_power = true;
> > + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> > + if (ret) {
> > + dev_err(dev, "request gpio %d failed\n", gpio);
> > + goto put_display_node;
> > + }
> > +
> > + ret = gpio_direction_output(gpio, og->active_low);
> > + if (ret) {
> > + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> > + goto put_display_node;
> > + }
> > + }
> > +
> > + if (is_gpio_power)
> > + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> > +
> > + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> > + if (ret < 0) {
> > + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> > + goto put_display_node;
> > + }
> > + pdata->lcd_wiring_mode = ret;
> > +
> > + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
> > +
> > + timings = of_get_display_timings(display_np);
> > + if (!timings) {
> > + dev_err(dev, "failed to get display timings\n");
> > + goto put_display_node;
> > + }
> > +
> > + timings_np = of_find_node_by_name(display_np, "display-timings");
> > + if (!timings_np) {
> > + dev_err(dev, "failed to find display-timings node\n");
> > + goto put_display_node;
> > + }
> > +
> > + for (i = 0; i < of_get_child_count(timings_np); i++) {
> > + struct videomode vm;
> > + struct fb_videomode fb_vm;
> > +
> > + ret = videomode_from_timing(timings, &vm, i);
> > + if (ret < 0)
> > + goto put_timings_node;
> > + ret = fb_videomode_from_videomode(&vm, &fb_vm);
> > + if (ret < 0)
> > + goto put_timings_node;
> > +
> > + fb_add_videomode(&fb_vm, &info->modelist);
> > + }
> > +
> > + return 0;
> > +
> > +put_timings_node:
> > + of_node_put(timings_np);
> > +put_display_node:
> > + of_node_put(display_np);
> > + return ret;
> > +}
> > +#else
> > +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> > +{
> > + return 0;
> > +}
> > +#endif
> >
> > static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > {
> > struct device *dev = &pdev->dev;
> > struct fb_info *info;
> > struct atmel_lcdfb_info *sinfo;
> > - struct atmel_lcdfb_pdata *pdata;
> > - struct fb_videomode fbmode;
> > + struct atmel_lcdfb_pdata *pdata = NULL;
> > struct resource *regs = NULL;
> > struct resource *map = NULL;
> > + struct fb_modelist *modelist;
> > int ret;
> >
> > dev_dbg(dev, "%s BEGIN\n", __func__);
> > @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > }
> >
> > sinfo = info->par;
> > + sinfo->pdev = pdev;
> > + sinfo->info = info;
> > +
> > + INIT_LIST_HEAD(&info->modelist);
> >
> > - if (dev->platform_data) {
> > - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
> > + if (pdev->dev.of_node) {
> > + ret = atmel_lcdfb_of_init(sinfo);
> > + if (ret)
> > + goto free_info;
> > + } else if (dev->platform_data) {
> > + struct fb_monspecs *monspecs;
> > + int i;
> > +
> > + pdata = dev->platform_data;
> > + monspecs = pdata->default_monspecs;
> > sinfo->pdata = *pdata;
> > +
> > + for (i = 0; i < monspecs->modedb_len; i++)
> > + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
> > +
> > + sinfo->config = atmel_lcdfb_get_config(pdev);
> > +
> > + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
> > + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> > } else {
> > dev_err(dev, "cannot get default configuration\n");
> > goto free_info;
> > }
> > - sinfo->info = info;
> > - sinfo->pdev = pdev;
> > - sinfo->config = atmel_lcdfb_get_config(pdev);
> > +
> > if (!sinfo->config)
> > goto free_info;
> >
> > @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > info->pseudo_palette = sinfo->pseudo_palette;
> > info->fbops = &atmel_lcdfb_ops;
> >
> > - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
> > info->fix = atmel_lcdfb_fix;
> >
> > /* Enable LCDC Clocks */
> > @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > }
> > atmel_lcdfb_start_clock(sinfo);
> >
> > - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
> > - info->monspecs.modedb_len, info->monspecs.modedb,
> > - pdata->default_bpp);
> > - if (!ret) {
> > - dev_err(dev, "no suitable video mode found\n");
> > - goto stop_clk;
> > - }
> > + modelist = list_first_entry(&info->modelist,
> > + struct fb_modelist, list);
> > + fb_videomode_to_var(&info->var, &modelist->mode);
> >
> > + atmel_lcdfb_check_var(&info->var, info);
> >
> > regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > if (!regs) {
> > @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > goto unregister_irqs;
> > }
> >
> > - /*
> > - * This makes sure that our colour bitfield
> > - * descriptors are correctly initialised.
> > - */
> > - atmel_lcdfb_check_var(&info->var, info);
> > -
> > - ret = fb_set_var(info, &info->var);
> > - if (ret) {
> > - dev_warn(dev, "unable to set display parameters\n");
> > - goto free_cmap;
> > - }
> > -
> > dev_set_drvdata(dev, info);
> >
> > /*
> > @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> > goto reset_drvdata;
> > }
> >
> > - /* add selected videomode to modelist */
> > - fb_var_to_videomode(&fbmode, &info->var);
> > - fb_add_videomode(&fbmode, &info->modelist);
> > -
> > /* Power up the LCDC screen */
> > atmel_lcdfb_power_control(sinfo, 1);
> >
> > @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
> >
> > reset_drvdata:
> > dev_set_drvdata(dev, NULL);
> > -free_cmap:
> > fb_dealloc_cmap(&info->cmap);
> > unregister_irqs:
> > cancel_work_sync(&sinfo->task);
> > @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
> > .driver = {
> > .name = "atmel_lcdfb",
> > .owner = THIS_MODULE,
> > + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
> > },
> > };
> >
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 5/8] ARM: at91: sam9g45: add lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-16 13:57 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 13:57 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: devicetree-discuss, linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
> index 6b1d4ca..ab8a8fc 100644
> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
> @@ -322,6 +322,42 @@
> };
> };
>
> + fb {
> + pinctrl_fb: fb-0 {
> + atmel,pins =
> + <4 0 0x1 0x0 /* PE0 periph A */
> + 4 2 0x1 0x0 /* PE2 periph A */
> + 4 3 0x1 0x0 /* PE3 periph A */
> + 4 4 0x1 0x0 /* PE4 periph A */
> + 4 5 0x1 0x0 /* PE5 periph A */
> + 4 6 0x1 0x0 /* PE6 periph A */
> + 4 7 0x1 0x0 /* PE7 periph A */
> + 4 8 0x1 0x0 /* PE8 periph A */
> + 4 9 0x1 0x0 /* PE9 periph A */
> + 4 10 0x1 0x0 /* PE10 periph A */
> + 4 11 0x1 0x0 /* PE11 periph A */
> + 4 12 0x1 0x0 /* PE12 periph A */
> + 4 13 0x1 0x0 /* PE13 periph A */
> + 4 14 0x1 0x0 /* PE14 periph A */
> + 4 15 0x1 0x0 /* PE15 periph A */
> + 4 16 0x1 0x0 /* PE16 periph A */
> + 4 17 0x1 0x0 /* PE17 periph A */
> + 4 18 0x1 0x0 /* PE18 periph A */
> + 4 19 0x1 0x0 /* PE19 periph A */
> + 4 20 0x1 0x0 /* PE20 periph A */
> + 4 21 0x1 0x0 /* PE21 periph A */
> + 4 22 0x1 0x0 /* PE22 periph A */
> + 4 23 0x1 0x0 /* PE23 periph A */
> + 4 24 0x1 0x0 /* PE24 periph A */
> + 4 25 0x1 0x0 /* PE25 periph A */
> + 4 26 0x1 0x0 /* PE26 periph A */
> + 4 27 0x1 0x0 /* PE27 periph A */
> + 4 28 0x1 0x0 /* PE28 periph A */
> + 4 29 0x1 0x0 /* PE29 periph A */
> + 4 30 0x1 0x0>; /* PE30 periph A */
Verified, correct.
> + };
> + };
> +
> pioA: gpio@fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -533,6 +569,17 @@
> };
> };
>
> + fb0: fb@0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
If we change to "atmel,at91sam9g45-lcdfb", we will have to change this
as-well.
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
I do not think we need these 2 properties: is a "reg" property existing
in child nodes?
> + };
> +
> nand0: nand@40000000 {
> compatible = "atmel,at91rm9200-nand";
> #address-cells = <1>;
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 5/8] ARM: at91: sam9g45: add lcd support
@ 2013-04-16 13:57 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 13:57 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
> index 6b1d4ca..ab8a8fc 100644
> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
> @@ -322,6 +322,42 @@
> };
> };
>
> + fb {
> + pinctrl_fb: fb-0 {
> + atmel,pins =
> + <4 0 0x1 0x0 /* PE0 periph A */
> + 4 2 0x1 0x0 /* PE2 periph A */
> + 4 3 0x1 0x0 /* PE3 periph A */
> + 4 4 0x1 0x0 /* PE4 periph A */
> + 4 5 0x1 0x0 /* PE5 periph A */
> + 4 6 0x1 0x0 /* PE6 periph A */
> + 4 7 0x1 0x0 /* PE7 periph A */
> + 4 8 0x1 0x0 /* PE8 periph A */
> + 4 9 0x1 0x0 /* PE9 periph A */
> + 4 10 0x1 0x0 /* PE10 periph A */
> + 4 11 0x1 0x0 /* PE11 periph A */
> + 4 12 0x1 0x0 /* PE12 periph A */
> + 4 13 0x1 0x0 /* PE13 periph A */
> + 4 14 0x1 0x0 /* PE14 periph A */
> + 4 15 0x1 0x0 /* PE15 periph A */
> + 4 16 0x1 0x0 /* PE16 periph A */
> + 4 17 0x1 0x0 /* PE17 periph A */
> + 4 18 0x1 0x0 /* PE18 periph A */
> + 4 19 0x1 0x0 /* PE19 periph A */
> + 4 20 0x1 0x0 /* PE20 periph A */
> + 4 21 0x1 0x0 /* PE21 periph A */
> + 4 22 0x1 0x0 /* PE22 periph A */
> + 4 23 0x1 0x0 /* PE23 periph A */
> + 4 24 0x1 0x0 /* PE24 periph A */
> + 4 25 0x1 0x0 /* PE25 periph A */
> + 4 26 0x1 0x0 /* PE26 periph A */
> + 4 27 0x1 0x0 /* PE27 periph A */
> + 4 28 0x1 0x0 /* PE28 periph A */
> + 4 29 0x1 0x0 /* PE29 periph A */
> + 4 30 0x1 0x0>; /* PE30 periph A */
Verified, correct.
> + };
> + };
> +
> pioA: gpio at fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -533,6 +569,17 @@
> };
> };
>
> + fb0: fb at 0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
If we change to "atmel,at91sam9g45-lcdfb", we will have to change this
as-well.
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
I do not think we need these 2 properties: is a "reg" property existing
in child nodes?
> + };
> +
> nand0: nand at 40000000 {
> compatible = "atmel,at91rm9200-nand";
> #address-cells = <1>;
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 5/8] ARM: at91: sam9g45: add lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-16 14:00 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:00 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: devicetree-discuss, linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
> index 6b1d4ca..ab8a8fc 100644
> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
> @@ -322,6 +322,42 @@
> };
> };
>
> + fb {
> + pinctrl_fb: fb-0 {
> + atmel,pins =
> + <4 0 0x1 0x0 /* PE0 periph A */
> + 4 2 0x1 0x0 /* PE2 periph A */
> + 4 3 0x1 0x0 /* PE3 periph A */
> + 4 4 0x1 0x0 /* PE4 periph A */
> + 4 5 0x1 0x0 /* PE5 periph A */
> + 4 6 0x1 0x0 /* PE6 periph A */
> + 4 7 0x1 0x0 /* PE7 periph A */
> + 4 8 0x1 0x0 /* PE8 periph A */
> + 4 9 0x1 0x0 /* PE9 periph A */
> + 4 10 0x1 0x0 /* PE10 periph A */
> + 4 11 0x1 0x0 /* PE11 periph A */
> + 4 12 0x1 0x0 /* PE12 periph A */
> + 4 13 0x1 0x0 /* PE13 periph A */
> + 4 14 0x1 0x0 /* PE14 periph A */
> + 4 15 0x1 0x0 /* PE15 periph A */
> + 4 16 0x1 0x0 /* PE16 periph A */
> + 4 17 0x1 0x0 /* PE17 periph A */
> + 4 18 0x1 0x0 /* PE18 periph A */
> + 4 19 0x1 0x0 /* PE19 periph A */
> + 4 20 0x1 0x0 /* PE20 periph A */
> + 4 21 0x1 0x0 /* PE21 periph A */
> + 4 22 0x1 0x0 /* PE22 periph A */
> + 4 23 0x1 0x0 /* PE23 periph A */
> + 4 24 0x1 0x0 /* PE24 periph A */
> + 4 25 0x1 0x0 /* PE25 periph A */
> + 4 26 0x1 0x0 /* PE26 periph A */
> + 4 27 0x1 0x0 /* PE27 periph A */
> + 4 28 0x1 0x0 /* PE28 periph A */
> + 4 29 0x1 0x0 /* PE29 periph A */
> + 4 30 0x1 0x0>; /* PE30 periph A */
> + };
> + };
> +
> pioA: gpio@fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -533,6 +569,17 @@
> };
> };
>
> + fb0: fb@0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
Error: here, it is <23 4 0>
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +
> nand0: nand@40000000 {
> compatible = "atmel,at91rm9200-nand";
> #address-cells = <1>;
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 5/8] ARM: at91: sam9g45: add lcd support
@ 2013-04-16 14:00 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:00 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
> index 6b1d4ca..ab8a8fc 100644
> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
> @@ -322,6 +322,42 @@
> };
> };
>
> + fb {
> + pinctrl_fb: fb-0 {
> + atmel,pins =
> + <4 0 0x1 0x0 /* PE0 periph A */
> + 4 2 0x1 0x0 /* PE2 periph A */
> + 4 3 0x1 0x0 /* PE3 periph A */
> + 4 4 0x1 0x0 /* PE4 periph A */
> + 4 5 0x1 0x0 /* PE5 periph A */
> + 4 6 0x1 0x0 /* PE6 periph A */
> + 4 7 0x1 0x0 /* PE7 periph A */
> + 4 8 0x1 0x0 /* PE8 periph A */
> + 4 9 0x1 0x0 /* PE9 periph A */
> + 4 10 0x1 0x0 /* PE10 periph A */
> + 4 11 0x1 0x0 /* PE11 periph A */
> + 4 12 0x1 0x0 /* PE12 periph A */
> + 4 13 0x1 0x0 /* PE13 periph A */
> + 4 14 0x1 0x0 /* PE14 periph A */
> + 4 15 0x1 0x0 /* PE15 periph A */
> + 4 16 0x1 0x0 /* PE16 periph A */
> + 4 17 0x1 0x0 /* PE17 periph A */
> + 4 18 0x1 0x0 /* PE18 periph A */
> + 4 19 0x1 0x0 /* PE19 periph A */
> + 4 20 0x1 0x0 /* PE20 periph A */
> + 4 21 0x1 0x0 /* PE21 periph A */
> + 4 22 0x1 0x0 /* PE22 periph A */
> + 4 23 0x1 0x0 /* PE23 periph A */
> + 4 24 0x1 0x0 /* PE24 periph A */
> + 4 25 0x1 0x0 /* PE25 periph A */
> + 4 26 0x1 0x0 /* PE26 periph A */
> + 4 27 0x1 0x0 /* PE27 periph A */
> + 4 28 0x1 0x0 /* PE28 periph A */
> + 4 29 0x1 0x0 /* PE29 periph A */
> + 4 30 0x1 0x0>; /* PE30 periph A */
> + };
> + };
> +
> pioA: gpio at fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -533,6 +569,17 @@
> };
> };
>
> + fb0: fb at 0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
Error: here, it is <23 4 0>
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +
> nand0: nand at 40000000 {
> compatible = "atmel,at91rm9200-nand";
> #address-cells = <1>;
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 6/8] ARM: at91: sam9263: add fb dt support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-16 14:11 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:11 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: devicetree-discuss, linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
> index 271d4de..3d0effa 100644
> --- a/arch/arm/boot/dts/at91sam9263.dtsi
> +++ b/arch/arm/boot/dts/at91sam9263.dtsi
> @@ -303,6 +303,34 @@
> };
> };
>
> + fb {
> + pinctrl_fb: fb-0 {
> + atmel,pins =
> + <2 1 0x1 0x0 /* PC1 periph A */
> + 2 2 0x1 0x0 /* PC2 periph A */
> + 2 3 0x1 0x0 /* PC3 periph A */
> + 1 9 0x2 0x0 /* PB9 periph B */
> + 2 6 0x1 0x0 /* PC6 periph A */
> + 2 7 0x1 0x0 /* PC7 periph A */
> + 2 8 0x1 0x0 /* PC8 periph A */
> + 2 9 0x1 0x0 /* PC9 periph A */
> + 2 10 0x1 0x0 /* PC10 periph A */
> + 2 11 0x1 0x0 /* PC11 periph A */
> + 2 14 0x1 0x0 /* PC14 periph A */
> + 2 15 0x1 0x0 /* PC15 periph A */
> + 2 16 0x1 0x0 /* PC16 periph A */
> + 2 12 0x2 0x0 /* PC12 periph B */
> + 2 18 0x1 0x0 /* PC18 periph A */
> + 2 19 0x1 0x0 /* PC19 periph A */
> + 2 22 0x1 0x0 /* PC22 periph A */
> + 2 23 0x1 0x0 /* PC23 periph A */
> + 2 24 0x1 0x0 /* PC24 periph A */
> + 2 17 0x2 0x0 /* PC17 periph B */
> + 2 26 0x1 0x0 /* PC26 periph A */
> + 2 27 0x1 0x0>; /* PC27 periph A */
Verified, okay.
> + };
> + };
> +
> pioA: gpio@fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -464,6 +492,17 @@
> };
> };
>
> + fb0: fb@0x00500000 {
No, it is 0x700000
> + compatible = "atmel,at91sam9263-lcdc";
> + reg = <0x00700000 0x1000>;
Ditto.
> + interrupts = <26 3 0>;
<26 4 0> here.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
Ditto in 9g45 case.
> + };
> +
> nand0: nand@40000000 {
> compatible = "atmel,at91rm9200-nand";
> #address-cells = <1>;
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 6/8] ARM: at91: sam9263: add fb dt support
@ 2013-04-16 14:11 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:11 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
> index 271d4de..3d0effa 100644
> --- a/arch/arm/boot/dts/at91sam9263.dtsi
> +++ b/arch/arm/boot/dts/at91sam9263.dtsi
> @@ -303,6 +303,34 @@
> };
> };
>
> + fb {
> + pinctrl_fb: fb-0 {
> + atmel,pins =
> + <2 1 0x1 0x0 /* PC1 periph A */
> + 2 2 0x1 0x0 /* PC2 periph A */
> + 2 3 0x1 0x0 /* PC3 periph A */
> + 1 9 0x2 0x0 /* PB9 periph B */
> + 2 6 0x1 0x0 /* PC6 periph A */
> + 2 7 0x1 0x0 /* PC7 periph A */
> + 2 8 0x1 0x0 /* PC8 periph A */
> + 2 9 0x1 0x0 /* PC9 periph A */
> + 2 10 0x1 0x0 /* PC10 periph A */
> + 2 11 0x1 0x0 /* PC11 periph A */
> + 2 14 0x1 0x0 /* PC14 periph A */
> + 2 15 0x1 0x0 /* PC15 periph A */
> + 2 16 0x1 0x0 /* PC16 periph A */
> + 2 12 0x2 0x0 /* PC12 periph B */
> + 2 18 0x1 0x0 /* PC18 periph A */
> + 2 19 0x1 0x0 /* PC19 periph A */
> + 2 22 0x1 0x0 /* PC22 periph A */
> + 2 23 0x1 0x0 /* PC23 periph A */
> + 2 24 0x1 0x0 /* PC24 periph A */
> + 2 17 0x2 0x0 /* PC17 periph B */
> + 2 26 0x1 0x0 /* PC26 periph A */
> + 2 27 0x1 0x0>; /* PC27 periph A */
Verified, okay.
> + };
> + };
> +
> pioA: gpio at fffff200 {
> compatible = "atmel,at91rm9200-gpio";
> reg = <0xfffff200 0x200>;
> @@ -464,6 +492,17 @@
> };
> };
>
> + fb0: fb at 0x00500000 {
No, it is 0x700000
> + compatible = "atmel,at91sam9263-lcdc";
> + reg = <0x00700000 0x1000>;
Ditto.
> + interrupts = <26 3 0>;
<26 4 0> here.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <1>;
Ditto in 9g45 case.
> + };
> +
> nand0: nand at 40000000 {
> compatible = "atmel,at91rm9200-nand";
> #address-cells = <1>;
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 6/8] ARM: at91: sam9263: add fb dt support
2013-04-16 14:11 ` Nicolas Ferre
@ 2013-04-16 14:13 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 14:13 UTC (permalink / raw)
To: Nicolas Ferre; +Cc: devicetree-discuss, linux-arm-kernel
On 16:11 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > ---
> > arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
> > 1 file changed, 39 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
> > index 271d4de..3d0effa 100644
> > --- a/arch/arm/boot/dts/at91sam9263.dtsi
> > +++ b/arch/arm/boot/dts/at91sam9263.dtsi
> > @@ -303,6 +303,34 @@
> > };
> > };
> >
> > + fb {
> > + pinctrl_fb: fb-0 {
> > + atmel,pins =
> > + <2 1 0x1 0x0 /* PC1 periph A */
> > + 2 2 0x1 0x0 /* PC2 periph A */
> > + 2 3 0x1 0x0 /* PC3 periph A */
> > + 1 9 0x2 0x0 /* PB9 periph B */
> > + 2 6 0x1 0x0 /* PC6 periph A */
> > + 2 7 0x1 0x0 /* PC7 periph A */
> > + 2 8 0x1 0x0 /* PC8 periph A */
> > + 2 9 0x1 0x0 /* PC9 periph A */
> > + 2 10 0x1 0x0 /* PC10 periph A */
> > + 2 11 0x1 0x0 /* PC11 periph A */
> > + 2 14 0x1 0x0 /* PC14 periph A */
> > + 2 15 0x1 0x0 /* PC15 periph A */
> > + 2 16 0x1 0x0 /* PC16 periph A */
> > + 2 12 0x2 0x0 /* PC12 periph B */
> > + 2 18 0x1 0x0 /* PC18 periph A */
> > + 2 19 0x1 0x0 /* PC19 periph A */
> > + 2 22 0x1 0x0 /* PC22 periph A */
> > + 2 23 0x1 0x0 /* PC23 periph A */
> > + 2 24 0x1 0x0 /* PC24 periph A */
> > + 2 17 0x2 0x0 /* PC17 periph B */
> > + 2 26 0x1 0x0 /* PC26 periph A */
> > + 2 27 0x1 0x0>; /* PC27 periph A */
>
> Verified, okay.
>
> > + };
> > + };
> > +
> > pioA: gpio@fffff200 {
> > compatible = "atmel,at91rm9200-gpio";
> > reg = <0xfffff200 0x200>;
> > @@ -464,6 +492,17 @@
> > };
> > };
> >
> > + fb0: fb@0x00500000 {
>
> No, it is 0x700000
>
> > + compatible = "atmel,at91sam9263-lcdc";
> > + reg = <0x00700000 0x1000>;
>
> Ditto.
>
> > + interrupts = <26 3 0>;
>
> <26 4 0> here.
no lcd is 3 even in c
and even 3 could be slow in some big lcd case
>
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fb>;
> > + status = "disabled";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
>
> Ditto in 9g45 case.
>
> > + };
> > +
> > nand0: nand@40000000 {
> > compatible = "atmel,at91rm9200-nand";
> > #address-cells = <1>;
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 6/8] ARM: at91: sam9263: add fb dt support
@ 2013-04-16 14:13 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 14:13 UTC (permalink / raw)
To: linux-arm-kernel
On 16:11 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > ---
> > arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
> > 1 file changed, 39 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
> > index 271d4de..3d0effa 100644
> > --- a/arch/arm/boot/dts/at91sam9263.dtsi
> > +++ b/arch/arm/boot/dts/at91sam9263.dtsi
> > @@ -303,6 +303,34 @@
> > };
> > };
> >
> > + fb {
> > + pinctrl_fb: fb-0 {
> > + atmel,pins =
> > + <2 1 0x1 0x0 /* PC1 periph A */
> > + 2 2 0x1 0x0 /* PC2 periph A */
> > + 2 3 0x1 0x0 /* PC3 periph A */
> > + 1 9 0x2 0x0 /* PB9 periph B */
> > + 2 6 0x1 0x0 /* PC6 periph A */
> > + 2 7 0x1 0x0 /* PC7 periph A */
> > + 2 8 0x1 0x0 /* PC8 periph A */
> > + 2 9 0x1 0x0 /* PC9 periph A */
> > + 2 10 0x1 0x0 /* PC10 periph A */
> > + 2 11 0x1 0x0 /* PC11 periph A */
> > + 2 14 0x1 0x0 /* PC14 periph A */
> > + 2 15 0x1 0x0 /* PC15 periph A */
> > + 2 16 0x1 0x0 /* PC16 periph A */
> > + 2 12 0x2 0x0 /* PC12 periph B */
> > + 2 18 0x1 0x0 /* PC18 periph A */
> > + 2 19 0x1 0x0 /* PC19 periph A */
> > + 2 22 0x1 0x0 /* PC22 periph A */
> > + 2 23 0x1 0x0 /* PC23 periph A */
> > + 2 24 0x1 0x0 /* PC24 periph A */
> > + 2 17 0x2 0x0 /* PC17 periph B */
> > + 2 26 0x1 0x0 /* PC26 periph A */
> > + 2 27 0x1 0x0>; /* PC27 periph A */
>
> Verified, okay.
>
> > + };
> > + };
> > +
> > pioA: gpio at fffff200 {
> > compatible = "atmel,at91rm9200-gpio";
> > reg = <0xfffff200 0x200>;
> > @@ -464,6 +492,17 @@
> > };
> > };
> >
> > + fb0: fb at 0x00500000 {
>
> No, it is 0x700000
>
> > + compatible = "atmel,at91sam9263-lcdc";
> > + reg = <0x00700000 0x1000>;
>
> Ditto.
>
> > + interrupts = <26 3 0>;
>
> <26 4 0> here.
no lcd is 3 even in c
and even 3 could be slow in some big lcd case
>
>
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fb>;
> > + status = "disabled";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
>
> Ditto in 9g45 case.
>
> > + };
> > +
> > nand0: nand at 40000000 {
> > compatible = "atmel,at91rm9200-nand";
> > #address-cells = <1>;
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 8/8] ARM: at91: sam9263ek: add dt lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-16 14:54 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:54 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: devicetree-discuss, linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9263ek.dts | 30 ++++++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
> index 1eb0872..d471b49 100644
> --- a/arch/arm/boot/dts/at91sam9263ek.dts
> +++ b/arch/arm/boot/dts/at91sam9263ek.dts
> @@ -81,6 +81,36 @@
> };
> };
>
> + fb0: fb@0x00500000 {
Ditto: Not good address: 0x700000
> + display = <&display0>;
> + status = "okay";
> +
> + display0: display {
> + bits-per-pixel = <16>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <4965000>;
> + hactive = <240>;
> + vactive = <320>;
> + hback-porch = <1>;
> + hfront-porch = <33>;
> + vback-porch = <1>;
> + vfront-porch = <0>;
> + hsync-len = <5>;
> + vsync-len = <1>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + };
> + };
> + };
> + };
Otherwise, seems good.
> +
> nand0: nand@40000000 {
> nand-bus-width = <8>;
> nand-ecc-mode = "soft";
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 8/8] ARM: at91: sam9263ek: add dt lcd support
@ 2013-04-16 14:54 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:54 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9263ek.dts | 30 ++++++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
> index 1eb0872..d471b49 100644
> --- a/arch/arm/boot/dts/at91sam9263ek.dts
> +++ b/arch/arm/boot/dts/at91sam9263ek.dts
> @@ -81,6 +81,36 @@
> };
> };
>
> + fb0: fb at 0x00500000 {
Ditto: Not good address: 0x700000
> + display = <&display0>;
> + status = "okay";
> +
> + display0: display {
> + bits-per-pixel = <16>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <4965000>;
> + hactive = <240>;
> + vactive = <320>;
> + hback-porch = <1>;
> + hfront-porch = <33>;
> + vback-porch = <1>;
> + vfront-porch = <0>;
> + hsync-len = <5>;
> + vsync-len = <1>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + };
> + };
> + };
> + };
Otherwise, seems good.
> +
> nand0: nand at 40000000 {
> nand-bus-width = <8>;
> nand-ecc-mode = "soft";
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 7/8] ARM: at91: at9sam9m10g45ek: add dt lcd support
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-16 14:56 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:56 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: devicetree-discuss, linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9m10g45ek.dts | 29 +++++++++++++++++++++++++++++
> 1 file changed, 29 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
> index 20c3191..79dc034 100644
> --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
> +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
> @@ -104,6 +104,35 @@
> };
> };
>
> + fb0: fb@0x00500000 {
> + display = <&display0>;
> + status = "okay";
> +
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = "RGB";
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> + };
> +
Seems good.
> nand0: nand@40000000 {
> nand-bus-width = <8>;
> nand-ecc-mode = "soft";
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 7/8] ARM: at91: at9sam9m10g45ek: add dt lcd support
@ 2013-04-16 14:56 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 14:56 UTC (permalink / raw)
To: linux-arm-kernel
On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/at91sam9m10g45ek.dts | 29 +++++++++++++++++++++++++++++
> 1 file changed, 29 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
> index 20c3191..79dc034 100644
> --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
> +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
> @@ -104,6 +104,35 @@
> };
> };
>
> + fb0: fb at 0x00500000 {
> + display = <&display0>;
> + status = "okay";
> +
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = "RGB";
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> + };
> +
Seems good.
> nand0: nand at 40000000 {
> nand-bus-width = <8>;
> nand-ecc-mode = "soft";
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 6/8] ARM: at91: sam9263: add fb dt support
2013-04-16 14:13 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2013-04-16 15:11 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:11 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: devicetree-discuss, linux-arm-kernel
On 04/16/2013 04:13 PM, Jean-Christophe PLAGNIOL-VILLARD :
> On 16:11 Tue 16 Apr , Nicolas Ferre wrote:
>> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>> ---
>>> arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
>>> 1 file changed, 39 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
>>> index 271d4de..3d0effa 100644
>>> --- a/arch/arm/boot/dts/at91sam9263.dtsi
>>> +++ b/arch/arm/boot/dts/at91sam9263.dtsi
>>> @@ -303,6 +303,34 @@
>>> };
>>> };
>>>
>>> + fb {
>>> + pinctrl_fb: fb-0 {
>>> + atmel,pins =
>>> + <2 1 0x1 0x0 /* PC1 periph A */
>>> + 2 2 0x1 0x0 /* PC2 periph A */
>>> + 2 3 0x1 0x0 /* PC3 periph A */
>>> + 1 9 0x2 0x0 /* PB9 periph B */
>>> + 2 6 0x1 0x0 /* PC6 periph A */
>>> + 2 7 0x1 0x0 /* PC7 periph A */
>>> + 2 8 0x1 0x0 /* PC8 periph A */
>>> + 2 9 0x1 0x0 /* PC9 periph A */
>>> + 2 10 0x1 0x0 /* PC10 periph A */
>>> + 2 11 0x1 0x0 /* PC11 periph A */
>>> + 2 14 0x1 0x0 /* PC14 periph A */
>>> + 2 15 0x1 0x0 /* PC15 periph A */
>>> + 2 16 0x1 0x0 /* PC16 periph A */
>>> + 2 12 0x2 0x0 /* PC12 periph B */
>>> + 2 18 0x1 0x0 /* PC18 periph A */
>>> + 2 19 0x1 0x0 /* PC19 periph A */
>>> + 2 22 0x1 0x0 /* PC22 periph A */
>>> + 2 23 0x1 0x0 /* PC23 periph A */
>>> + 2 24 0x1 0x0 /* PC24 periph A */
>>> + 2 17 0x2 0x0 /* PC17 periph B */
>>> + 2 26 0x1 0x0 /* PC26 periph A */
>>> + 2 27 0x1 0x0>; /* PC27 periph A */
>>
>> Verified, okay.
>>
>>> + };
>>> + };
>>> +
>>> pioA: gpio@fffff200 {
>>> compatible = "atmel,at91rm9200-gpio";
>>> reg = <0xfffff200 0x200>;
>>> @@ -464,6 +492,17 @@
>>> };
>>> };
>>>
>>> + fb0: fb@0x00500000 {
>>
>> No, it is 0x700000
>>
>>> + compatible = "atmel,at91sam9263-lcdc";
>>> + reg = <0x00700000 0x1000>;
>>
>> Ditto.
>>
>>> + interrupts = <26 3 0>;
>>
>> <26 4 0> here.
> no lcd is 3 even in c
>
> and even 3 could be slow in some big lcd case
No, you mean the priority, but priority is encoded as the 3rd cell. So,
we end up with:
<26 4 3>
(I agree with the 3)
>>
>>
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_fb>;
>>> + status = "disabled";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>
>> Ditto in 9g45 case.
>>
>>> + };
>>> +
>>> nand0: nand@40000000 {
>>> compatible = "atmel,at91rm9200-nand";
>>> #address-cells = <1>;
>>>
>>
>>
>> --
>> Nicolas Ferre
>
Bye,
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 6/8] ARM: at91: sam9263: add fb dt support
@ 2013-04-16 15:11 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:11 UTC (permalink / raw)
To: linux-arm-kernel
On 04/16/2013 04:13 PM, Jean-Christophe PLAGNIOL-VILLARD :
> On 16:11 Tue 16 Apr , Nicolas Ferre wrote:
>> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>> ---
>>> arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
>>> 1 file changed, 39 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
>>> index 271d4de..3d0effa 100644
>>> --- a/arch/arm/boot/dts/at91sam9263.dtsi
>>> +++ b/arch/arm/boot/dts/at91sam9263.dtsi
>>> @@ -303,6 +303,34 @@
>>> };
>>> };
>>>
>>> + fb {
>>> + pinctrl_fb: fb-0 {
>>> + atmel,pins =
>>> + <2 1 0x1 0x0 /* PC1 periph A */
>>> + 2 2 0x1 0x0 /* PC2 periph A */
>>> + 2 3 0x1 0x0 /* PC3 periph A */
>>> + 1 9 0x2 0x0 /* PB9 periph B */
>>> + 2 6 0x1 0x0 /* PC6 periph A */
>>> + 2 7 0x1 0x0 /* PC7 periph A */
>>> + 2 8 0x1 0x0 /* PC8 periph A */
>>> + 2 9 0x1 0x0 /* PC9 periph A */
>>> + 2 10 0x1 0x0 /* PC10 periph A */
>>> + 2 11 0x1 0x0 /* PC11 periph A */
>>> + 2 14 0x1 0x0 /* PC14 periph A */
>>> + 2 15 0x1 0x0 /* PC15 periph A */
>>> + 2 16 0x1 0x0 /* PC16 periph A */
>>> + 2 12 0x2 0x0 /* PC12 periph B */
>>> + 2 18 0x1 0x0 /* PC18 periph A */
>>> + 2 19 0x1 0x0 /* PC19 periph A */
>>> + 2 22 0x1 0x0 /* PC22 periph A */
>>> + 2 23 0x1 0x0 /* PC23 periph A */
>>> + 2 24 0x1 0x0 /* PC24 periph A */
>>> + 2 17 0x2 0x0 /* PC17 periph B */
>>> + 2 26 0x1 0x0 /* PC26 periph A */
>>> + 2 27 0x1 0x0>; /* PC27 periph A */
>>
>> Verified, okay.
>>
>>> + };
>>> + };
>>> +
>>> pioA: gpio at fffff200 {
>>> compatible = "atmel,at91rm9200-gpio";
>>> reg = <0xfffff200 0x200>;
>>> @@ -464,6 +492,17 @@
>>> };
>>> };
>>>
>>> + fb0: fb at 0x00500000 {
>>
>> No, it is 0x700000
>>
>>> + compatible = "atmel,at91sam9263-lcdc";
>>> + reg = <0x00700000 0x1000>;
>>
>> Ditto.
>>
>>> + interrupts = <26 3 0>;
>>
>> <26 4 0> here.
> no lcd is 3 even in c
>
> and even 3 could be slow in some big lcd case
No, you mean the priority, but priority is encoded as the 3rd cell. So,
we end up with:
<26 4 3>
(I agree with the 3)
>>
>>
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_fb>;
>>> + status = "disabled";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>
>> Ditto in 9g45 case.
>>
>>> + };
>>> +
>>> nand0: nand at 40000000 {
>>> compatible = "atmel,at91rm9200-nand";
>>> #address-cells = <1>;
>>>
>>
>>
>> --
>> Nicolas Ferre
>
Bye,
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 5/8] ARM: at91: sam9g45: add lcd support
2013-04-16 14:00 ` Nicolas Ferre
@ 2013-04-16 15:12 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:12 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On 04/16/2013 04:00 PM, Nicolas Ferre :
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
>> Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
>> ---
>> arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
>> 1 file changed, 47 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
>> index 6b1d4ca..ab8a8fc 100644
>> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
>> @@ -322,6 +322,42 @@
>> };
>> };
>>
>> + fb {
>> + pinctrl_fb: fb-0 {
>> + atmel,pins =
>> + <4 0 0x1 0x0 /* PE0 periph A */
>> + 4 2 0x1 0x0 /* PE2 periph A */
>> + 4 3 0x1 0x0 /* PE3 periph A */
>> + 4 4 0x1 0x0 /* PE4 periph A */
>> + 4 5 0x1 0x0 /* PE5 periph A */
>> + 4 6 0x1 0x0 /* PE6 periph A */
>> + 4 7 0x1 0x0 /* PE7 periph A */
>> + 4 8 0x1 0x0 /* PE8 periph A */
>> + 4 9 0x1 0x0 /* PE9 periph A */
>> + 4 10 0x1 0x0 /* PE10 periph A */
>> + 4 11 0x1 0x0 /* PE11 periph A */
>> + 4 12 0x1 0x0 /* PE12 periph A */
>> + 4 13 0x1 0x0 /* PE13 periph A */
>> + 4 14 0x1 0x0 /* PE14 periph A */
>> + 4 15 0x1 0x0 /* PE15 periph A */
>> + 4 16 0x1 0x0 /* PE16 periph A */
>> + 4 17 0x1 0x0 /* PE17 periph A */
>> + 4 18 0x1 0x0 /* PE18 periph A */
>> + 4 19 0x1 0x0 /* PE19 periph A */
>> + 4 20 0x1 0x0 /* PE20 periph A */
>> + 4 21 0x1 0x0 /* PE21 periph A */
>> + 4 22 0x1 0x0 /* PE22 periph A */
>> + 4 23 0x1 0x0 /* PE23 periph A */
>> + 4 24 0x1 0x0 /* PE24 periph A */
>> + 4 25 0x1 0x0 /* PE25 periph A */
>> + 4 26 0x1 0x0 /* PE26 periph A */
>> + 4 27 0x1 0x0 /* PE27 periph A */
>> + 4 28 0x1 0x0 /* PE28 periph A */
>> + 4 29 0x1 0x0 /* PE29 periph A */
>> + 4 30 0x1 0x0>; /* PE30 periph A */
>> + };
>> + };
>> +
>> pioA: gpio@fffff200 {
>> compatible = "atmel,at91rm9200-gpio";
>> reg = <0xfffff200 0x200>;
>> @@ -533,6 +569,17 @@
>> };
>> };
>>
>> + fb0: fb@0x00500000 {
>> + compatible = "atmel,at91sam9g45-lcdc";
>> + reg = <0x00500000 0x1000>;
>> + interrupts = <23 3 0>;
>
> Error: here, it is <23 4 0>
Collecting all the remarks, we end-up with:
<23 4 3>
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_fb>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + };
>> +
>> nand0: nand@40000000 {
>> compatible = "atmel,at91rm9200-nand";
>> #address-cells = <1>;
>>
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 5/8] ARM: at91: sam9g45: add lcd support
@ 2013-04-16 15:12 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:12 UTC (permalink / raw)
To: linux-arm-kernel
On 04/16/2013 04:00 PM, Nicolas Ferre :
> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>> ---
>> arch/arm/boot/dts/at91sam9g45.dtsi | 47 ++++++++++++++++++++++++++++++++++++
>> 1 file changed, 47 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
>> index 6b1d4ca..ab8a8fc 100644
>> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
>> @@ -322,6 +322,42 @@
>> };
>> };
>>
>> + fb {
>> + pinctrl_fb: fb-0 {
>> + atmel,pins =
>> + <4 0 0x1 0x0 /* PE0 periph A */
>> + 4 2 0x1 0x0 /* PE2 periph A */
>> + 4 3 0x1 0x0 /* PE3 periph A */
>> + 4 4 0x1 0x0 /* PE4 periph A */
>> + 4 5 0x1 0x0 /* PE5 periph A */
>> + 4 6 0x1 0x0 /* PE6 periph A */
>> + 4 7 0x1 0x0 /* PE7 periph A */
>> + 4 8 0x1 0x0 /* PE8 periph A */
>> + 4 9 0x1 0x0 /* PE9 periph A */
>> + 4 10 0x1 0x0 /* PE10 periph A */
>> + 4 11 0x1 0x0 /* PE11 periph A */
>> + 4 12 0x1 0x0 /* PE12 periph A */
>> + 4 13 0x1 0x0 /* PE13 periph A */
>> + 4 14 0x1 0x0 /* PE14 periph A */
>> + 4 15 0x1 0x0 /* PE15 periph A */
>> + 4 16 0x1 0x0 /* PE16 periph A */
>> + 4 17 0x1 0x0 /* PE17 periph A */
>> + 4 18 0x1 0x0 /* PE18 periph A */
>> + 4 19 0x1 0x0 /* PE19 periph A */
>> + 4 20 0x1 0x0 /* PE20 periph A */
>> + 4 21 0x1 0x0 /* PE21 periph A */
>> + 4 22 0x1 0x0 /* PE22 periph A */
>> + 4 23 0x1 0x0 /* PE23 periph A */
>> + 4 24 0x1 0x0 /* PE24 periph A */
>> + 4 25 0x1 0x0 /* PE25 periph A */
>> + 4 26 0x1 0x0 /* PE26 periph A */
>> + 4 27 0x1 0x0 /* PE27 periph A */
>> + 4 28 0x1 0x0 /* PE28 periph A */
>> + 4 29 0x1 0x0 /* PE29 periph A */
>> + 4 30 0x1 0x0>; /* PE30 periph A */
>> + };
>> + };
>> +
>> pioA: gpio at fffff200 {
>> compatible = "atmel,at91rm9200-gpio";
>> reg = <0xfffff200 0x200>;
>> @@ -533,6 +569,17 @@
>> };
>> };
>>
>> + fb0: fb at 0x00500000 {
>> + compatible = "atmel,at91sam9g45-lcdc";
>> + reg = <0x00500000 0x1000>;
>> + interrupts = <23 3 0>;
>
> Error: here, it is <23 4 0>
Collecting all the remarks, we end-up with:
<23 4 3>
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_fb>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + };
>> +
>> nand0: nand at 40000000 {
>> compatible = "atmel,at91rm9200-nand";
>> #address-cells = <1>;
>>
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-04-16 15:43 ` Nicolas Ferre
-1 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:43 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: Andrew Morton, devicetree-discuss, linux-fbdev, linux-arm-kernel
On 04/16/2013 03:44 PM, Jean-Christophe PLAGNIOL-VILLARD :
> On 15:42 Tue 16 Apr , Nicolas Ferre wrote:
>> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>>> get display timings from device tree
>>> Use videomode helpers to get display timings and configurations from
>>> device tree
>>
>> 2 sentences? Simply elaborate the 2nd one and it will be good.
>>
>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> Cc: linux-fbdev@vger.kernel.org
>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>> Cc: Andrew Morton <akpm@linux-foundation.org>
>>> ---
>>> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
>>> drivers/video/Kconfig | 2 +
>>> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
>>> 3 files changed, 289 insertions(+), 32 deletions(-)
>>> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>> new file mode 100644
>>> index 0000000..1ec175e
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>
>> Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
>> is even more self-explanatory...
> we do not describe drivers but IP
fine, but in
static const struct platform_device_id atmel_lcdfb_devtypes, we use
"xxx-lcdfb" type...
>>
>>> @@ -0,0 +1,75 @@
>>> +Atmel LCDC Framebuffer
>>> +-----------------------------------------------------
>>> +
>>> +Required properties:
>>> +- compatible :
>>> + "atmel,at91sam9261-lcdc" ,
>>> + "atmel,at91sam9263-lcdc" ,
>>> + "atmel,at91sam9g10-lcdc" ,
>>> + "atmel,at91sam9g45-lcdc" ,
>>> + "atmel,at91sam9g45es-lcdc" ,
>>> + "atmel,at91sam9rl-lcdc" ,
>>> + "atmel,at32ap-lcdc"
>>> +- reg : Should contain 1 register ranges(address and length)
>>> +- interrupts : framebuffer controller interrupt
>>> +- display: a phandle pointing to the display node
>>> +
>>> +Required nodes:
>>> +- display: a display node is required to initialize the lcd panel
>>> + This should be in the board dts.
>>> +- default-mode: a videomode within the display with timing parameters
>>> + as specified below.
>>> +
>>> +Example:
>>> +
>>> + fb0: fb@0x00500000 {
>>> + compatible = "atmel,at91sam9g45-lcdc";
>>> + reg = <0x00500000 0x1000>;
>>> + interrupts = <23 3 0>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_fb>;
>>> + display = <&display0>;
>>> + status = "okay";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> +
>>> + };
>>> +
>>> +Atmel LCDC Display
>>> +-----------------------------------------------------
>>> +Required properties (as per of_videomode_helper):
>>
>> Can you please point somewhere to the documentation:
>> Documentation/devicetree/bindings/video/display-timing.txt
>>
>>> + - atmel,dmacon: dma controler configuration
>>
>> Typo: controller.
>>
>>> + - atmel,lcdcon2: lcd controler configuration
>>
>> Ditto
>>
>>> + - atmel,guard-time: lcd guard time (Delay in frame periods)
>>
>> periods -> period, no?
> no it's periods even in the datasheet
>>
>>> + - bits-per-pixel: lcd panel bit-depth.
>>> +
>>> +Optional properties (as per of_videomode_helper):
>>> + - atmel,lcdcon-backlight: enable backlight
>>> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
>>
>> Is it a sting, or a number (as seen below)? If it is a number, please
>> tell how to choose the index.
> String
Okay: so tell it in the description and correct the example below.
>>> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
>>> +
>>> +Example:
>>> + display0: display {
>>> + bits-per-pixel = <32>;
>>> + atmel,lcdcon-backlight;
>>> + atmel,dmacon = <0x1>;
>>> + atmel,lcdcon2 = <0x80008002>;
>>> + atmel,guard-time = <9>;
>>> + atmel,lcd-wiring-mode = <1>;
Here ----------------------------------^^^^
>>> +
>>> + display-timings {
>>> + native-mode = <&timing0>;
>>> + timing0: timing0 {
>>> + clock-frequency = <9000000>;
>>> + hactive = <480>;
>>> + vactive = <272>;
>>> + hback-porch = <1>;
>>> + hfront-porch = <1>;
>>> + vback-porch = <40>;
>>> + vfront-porch = <1>;
>>> + hsync-len = <45>;
>>> + vsync-len = <1>;
>>> + };
>>> + };
>>> + };
>>> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
>>> index 4c1546f..0687482 100644
>>> --- a/drivers/video/Kconfig
>>> +++ b/drivers/video/Kconfig
>>> @@ -1018,6 +1018,8 @@ config FB_ATMEL
>>> select FB_CFB_FILLRECT
>>> select FB_CFB_COPYAREA
>>> select FB_CFB_IMAGEBLIT
>>> + select FB_MODE_HELPERS
>>> + select OF_VIDEOMODE
>>> help
>>> This enables support for the AT91/AT32 LCD Controller.
>>>
>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>>> index f67e226..4a31570 100644
>>> --- a/drivers/video/atmel_lcdfb.c
>>> +++ b/drivers/video/atmel_lcdfb.c
>>> @@ -20,7 +20,11 @@
>>> #include <linux/gfp.h>
>>> #include <linux/module.h>
>>> #include <linux/platform_data/atmel.h>
>>> +#include <linux/of.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/of_gpio.h>
>>> #include <video/of_display_timing.h>
>>
>> As said in patch 1/8, this one belongs to this 4/8 patch.
>>
>>> +#include <video/videomode.h>
>>>
>>> #include <mach/cpu.h>
>>> #include <asm/gpio.h>
>>> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
>>> struct atmel_lcdfb_config *config;
>>> };
>>>
>>> +struct atmel_lcdfb_power_ctrl_gpio {
>>> + int gpio;
>>> + int active_low;
>>> +
>>> + struct list_head list;
>>> +};
>>> +
>>> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
>>> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>>>
>>> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
>>> clk_disable(sinfo->lcdc_clk);
>>> }
>>>
>>> +#ifdef CONFIG_OF
>>> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
>>> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
>>> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
>>> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
>>> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
>>> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
>>> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
>>> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
>>> + { /* sentinel */ }
>>> +};
>>> +
>>> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
>>> +
>>> +static const char *atmel_lcdfb_wiring_modes[] = {
>>> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
>>> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
>>> +};
>>> +
>>> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
>>> +{
>>> + const char *mode;
>>> + int err, i;
>>> +
>>> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
>>> + if (err < 0)
>>> + return ATMEL_LCDC_WIRING_BGR;
>>> +
>>> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
>>> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
>>> + return i;
>>> +
>>> + return -ENODEV;
>>> +}
>>> +
>>> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
>>> +{
>>> + struct atmel_lcdfb_power_ctrl_gpio *og;
>>> +
>>> + list_for_each_entry(og, &pdata->pwr_gpios, list)
>>> + gpio_set_value(og->gpio, on);
>>> +}
>>> +
>>> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
>>> +{
>>> + struct fb_info *info = sinfo->info;
>>> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>>> + struct fb_var_screeninfo *var = &info->var;
>>> + struct device *dev = &sinfo->pdev->dev;
>>> + struct device_node *np =dev->of_node;
>>> + struct device_node *display_np;
>>> + struct device_node *timings_np;
>>> + struct display_timings *timings;
>>> + enum of_gpio_flags flags;
>>> + struct atmel_lcdfb_power_ctrl_gpio *og;
>>> + bool is_gpio_power = false;
>>> + int ret = -ENOENT;
>>> + int i, gpio;
>>> +
>>> + sinfo->config = (struct atmel_lcdfb_config*)
>>> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
>>
>> Please split it in 2 steps, otherwise the day that the drivers doesn't
>> find the device in dt_ids table, it hangs here with an Oops.
> no as you will never end here in this case
Ok, I see.
>>
>>> +
>>> + display_np = of_parse_phandle(np, "display", 0);
>>> + if (!display_np) {
>>> + dev_err(dev, "failed to find display phandle\n");
>>> + return -ENOENT;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property bits-per-pixel\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property atmel,guard-time\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property bits-per-pixel\n");
>>
>> No, wrong error message.
>>
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = -ENOMEM;
>>> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
>>> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
>>> + i, &flags);
>>> + if (gpio < 0)
>>> + continue;
>>> +
>>> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
>>> + if (!og)
>>> + goto put_display_node;
>>> +
>>> + og->gpio = gpio;
>>> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
>>> + is_gpio_power = true;
>>> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
>>> + if (ret) {
>>> + dev_err(dev, "request gpio %d failed\n", gpio);
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = gpio_direction_output(gpio, og->active_low);
>>> + if (ret) {
>>> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
>>> + goto put_display_node;
>>> + }
>>> + }
>>> +
>>> + if (is_gpio_power)
>>> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
>>> +
>>> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
>>> + if (ret < 0) {
>>> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
>>> + goto put_display_node;
>>> + }
>>> + pdata->lcd_wiring_mode = ret;
>>> +
>>> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
>>> +
>>> + timings = of_get_display_timings(display_np);
>>> + if (!timings) {
>>> + dev_err(dev, "failed to get display timings\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + timings_np = of_find_node_by_name(display_np, "display-timings");
>>> + if (!timings_np) {
>>> + dev_err(dev, "failed to find display-timings node\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + for (i = 0; i < of_get_child_count(timings_np); i++) {
>>> + struct videomode vm;
>>> + struct fb_videomode fb_vm;
>>> +
>>> + ret = videomode_from_timing(timings, &vm, i);
>>> + if (ret < 0)
>>> + goto put_timings_node;
>>> + ret = fb_videomode_from_videomode(&vm, &fb_vm);
>>> + if (ret < 0)
>>> + goto put_timings_node;
>>> +
>>> + fb_add_videomode(&fb_vm, &info->modelist);
>>> + }
>>> +
>>> + return 0;
>>> +
>>> +put_timings_node:
>>> + of_node_put(timings_np);
>>> +put_display_node:
>>> + of_node_put(display_np);
>>> + return ret;
>>> +}
>>> +#else
>>> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
>>> +{
>>> + return 0;
>>> +}
>>> +#endif
>>>
>>> static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> {
>>> struct device *dev = &pdev->dev;
>>> struct fb_info *info;
>>> struct atmel_lcdfb_info *sinfo;
>>> - struct atmel_lcdfb_pdata *pdata;
>>> - struct fb_videomode fbmode;
>>> + struct atmel_lcdfb_pdata *pdata = NULL;
>>> struct resource *regs = NULL;
>>> struct resource *map = NULL;
>>> + struct fb_modelist *modelist;
>>> int ret;
>>>
>>> dev_dbg(dev, "%s BEGIN\n", __func__);
>>> @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> }
>>>
>>> sinfo = info->par;
>>> + sinfo->pdev = pdev;
>>> + sinfo->info = info;
>>> +
>>> + INIT_LIST_HEAD(&info->modelist);
>>>
>>> - if (dev->platform_data) {
>>> - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
>>> + if (pdev->dev.of_node) {
>>> + ret = atmel_lcdfb_of_init(sinfo);
>>> + if (ret)
>>> + goto free_info;
>>> + } else if (dev->platform_data) {
>>> + struct fb_monspecs *monspecs;
>>> + int i;
>>> +
>>> + pdata = dev->platform_data;
>>> + monspecs = pdata->default_monspecs;
>>> sinfo->pdata = *pdata;
>>> +
>>> + for (i = 0; i < monspecs->modedb_len; i++)
>>> + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
>>> +
>>> + sinfo->config = atmel_lcdfb_get_config(pdev);
>>> +
>>> + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
>>> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
>>> } else {
>>> dev_err(dev, "cannot get default configuration\n");
>>> goto free_info;
>>> }
>>> - sinfo->info = info;
>>> - sinfo->pdev = pdev;
>>> - sinfo->config = atmel_lcdfb_get_config(pdev);
>>> +
>>> if (!sinfo->config)
>>> goto free_info;
>>>
>>> @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> info->pseudo_palette = sinfo->pseudo_palette;
>>> info->fbops = &atmel_lcdfb_ops;
>>>
>>> - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
>>> info->fix = atmel_lcdfb_fix;
>>>
>>> /* Enable LCDC Clocks */
>>> @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> }
>>> atmel_lcdfb_start_clock(sinfo);
>>>
>>> - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
>>> - info->monspecs.modedb_len, info->monspecs.modedb,
>>> - pdata->default_bpp);
>>> - if (!ret) {
>>> - dev_err(dev, "no suitable video mode found\n");
>>> - goto stop_clk;
>>> - }
>>> + modelist = list_first_entry(&info->modelist,
>>> + struct fb_modelist, list);
>>> + fb_videomode_to_var(&info->var, &modelist->mode);
>>>
>>> + atmel_lcdfb_check_var(&info->var, info);
>>>
>>> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> if (!regs) {
>>> @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> goto unregister_irqs;
>>> }
>>>
>>> - /*
>>> - * This makes sure that our colour bitfield
>>> - * descriptors are correctly initialised.
>>> - */
>>> - atmel_lcdfb_check_var(&info->var, info);
>>> -
>>> - ret = fb_set_var(info, &info->var);
>>> - if (ret) {
>>> - dev_warn(dev, "unable to set display parameters\n");
>>> - goto free_cmap;
>>> - }
>>> -
>>> dev_set_drvdata(dev, info);
>>>
>>> /*
>>> @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> goto reset_drvdata;
>>> }
>>>
>>> - /* add selected videomode to modelist */
>>> - fb_var_to_videomode(&fbmode, &info->var);
>>> - fb_add_videomode(&fbmode, &info->modelist);
>>> -
>>> /* Power up the LCDC screen */
>>> atmel_lcdfb_power_control(sinfo, 1);
>>>
>>> @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>>
>>> reset_drvdata:
>>> dev_set_drvdata(dev, NULL);
>>> -free_cmap:
>>> fb_dealloc_cmap(&info->cmap);
>>> unregister_irqs:
>>> cancel_work_sync(&sinfo->task);
>>> @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
>>> .driver = {
>>> .name = "atmel_lcdfb",
>>> .owner = THIS_MODULE,
>>> + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
>>> },
>>> };
>>>
>>>
>>
>>
>> --
>> Nicolas Ferre
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-16 15:43 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:43 UTC (permalink / raw)
To: linux-arm-kernel
On 04/16/2013 03:44 PM, Jean-Christophe PLAGNIOL-VILLARD :
> On 15:42 Tue 16 Apr , Nicolas Ferre wrote:
>> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>>> get display timings from device tree
>>> Use videomode helpers to get display timings and configurations from
>>> device tree
>>
>> 2 sentences? Simply elaborate the 2nd one and it will be good.
>>
>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> Cc: linux-fbdev@vger.kernel.org
>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>> Cc: Andrew Morton <akpm@linux-foundation.org>
>>> ---
>>> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
>>> drivers/video/Kconfig | 2 +
>>> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
>>> 3 files changed, 289 insertions(+), 32 deletions(-)
>>> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>> new file mode 100644
>>> index 0000000..1ec175e
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>
>> Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
>> is even more self-explanatory...
> we do not describe drivers but IP
fine, but in
static const struct platform_device_id atmel_lcdfb_devtypes, we use
"xxx-lcdfb" type...
>>
>>> @@ -0,0 +1,75 @@
>>> +Atmel LCDC Framebuffer
>>> +-----------------------------------------------------
>>> +
>>> +Required properties:
>>> +- compatible :
>>> + "atmel,at91sam9261-lcdc" ,
>>> + "atmel,at91sam9263-lcdc" ,
>>> + "atmel,at91sam9g10-lcdc" ,
>>> + "atmel,at91sam9g45-lcdc" ,
>>> + "atmel,at91sam9g45es-lcdc" ,
>>> + "atmel,at91sam9rl-lcdc" ,
>>> + "atmel,at32ap-lcdc"
>>> +- reg : Should contain 1 register ranges(address and length)
>>> +- interrupts : framebuffer controller interrupt
>>> +- display: a phandle pointing to the display node
>>> +
>>> +Required nodes:
>>> +- display: a display node is required to initialize the lcd panel
>>> + This should be in the board dts.
>>> +- default-mode: a videomode within the display with timing parameters
>>> + as specified below.
>>> +
>>> +Example:
>>> +
>>> + fb0: fb@0x00500000 {
>>> + compatible = "atmel,at91sam9g45-lcdc";
>>> + reg = <0x00500000 0x1000>;
>>> + interrupts = <23 3 0>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_fb>;
>>> + display = <&display0>;
>>> + status = "okay";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> +
>>> + };
>>> +
>>> +Atmel LCDC Display
>>> +-----------------------------------------------------
>>> +Required properties (as per of_videomode_helper):
>>
>> Can you please point somewhere to the documentation:
>> Documentation/devicetree/bindings/video/display-timing.txt
>>
>>> + - atmel,dmacon: dma controler configuration
>>
>> Typo: controller.
>>
>>> + - atmel,lcdcon2: lcd controler configuration
>>
>> Ditto
>>
>>> + - atmel,guard-time: lcd guard time (Delay in frame periods)
>>
>> periods -> period, no?
> no it's periods even in the datasheet
>>
>>> + - bits-per-pixel: lcd panel bit-depth.
>>> +
>>> +Optional properties (as per of_videomode_helper):
>>> + - atmel,lcdcon-backlight: enable backlight
>>> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
>>
>> Is it a sting, or a number (as seen below)? If it is a number, please
>> tell how to choose the index.
> String
Okay: so tell it in the description and correct the example below.
>>> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
>>> +
>>> +Example:
>>> + display0: display {
>>> + bits-per-pixel = <32>;
>>> + atmel,lcdcon-backlight;
>>> + atmel,dmacon = <0x1>;
>>> + atmel,lcdcon2 = <0x80008002>;
>>> + atmel,guard-time = <9>;
>>> + atmel,lcd-wiring-mode = <1>;
Here ----------------------------------^^^^
>>> +
>>> + display-timings {
>>> + native-mode = <&timing0>;
>>> + timing0: timing0 {
>>> + clock-frequency = <9000000>;
>>> + hactive = <480>;
>>> + vactive = <272>;
>>> + hback-porch = <1>;
>>> + hfront-porch = <1>;
>>> + vback-porch = <40>;
>>> + vfront-porch = <1>;
>>> + hsync-len = <45>;
>>> + vsync-len = <1>;
>>> + };
>>> + };
>>> + };
>>> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
>>> index 4c1546f..0687482 100644
>>> --- a/drivers/video/Kconfig
>>> +++ b/drivers/video/Kconfig
>>> @@ -1018,6 +1018,8 @@ config FB_ATMEL
>>> select FB_CFB_FILLRECT
>>> select FB_CFB_COPYAREA
>>> select FB_CFB_IMAGEBLIT
>>> + select FB_MODE_HELPERS
>>> + select OF_VIDEOMODE
>>> help
>>> This enables support for the AT91/AT32 LCD Controller.
>>>
>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>>> index f67e226..4a31570 100644
>>> --- a/drivers/video/atmel_lcdfb.c
>>> +++ b/drivers/video/atmel_lcdfb.c
>>> @@ -20,7 +20,11 @@
>>> #include <linux/gfp.h>
>>> #include <linux/module.h>
>>> #include <linux/platform_data/atmel.h>
>>> +#include <linux/of.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/of_gpio.h>
>>> #include <video/of_display_timing.h>
>>
>> As said in patch 1/8, this one belongs to this 4/8 patch.
>>
>>> +#include <video/videomode.h>
>>>
>>> #include <mach/cpu.h>
>>> #include <asm/gpio.h>
>>> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
>>> struct atmel_lcdfb_config *config;
>>> };
>>>
>>> +struct atmel_lcdfb_power_ctrl_gpio {
>>> + int gpio;
>>> + int active_low;
>>> +
>>> + struct list_head list;
>>> +};
>>> +
>>> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
>>> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>>>
>>> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
>>> clk_disable(sinfo->lcdc_clk);
>>> }
>>>
>>> +#ifdef CONFIG_OF
>>> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
>>> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
>>> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
>>> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
>>> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
>>> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
>>> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
>>> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
>>> + { /* sentinel */ }
>>> +};
>>> +
>>> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
>>> +
>>> +static const char *atmel_lcdfb_wiring_modes[] = {
>>> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
>>> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
>>> +};
>>> +
>>> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
>>> +{
>>> + const char *mode;
>>> + int err, i;
>>> +
>>> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
>>> + if (err < 0)
>>> + return ATMEL_LCDC_WIRING_BGR;
>>> +
>>> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
>>> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
>>> + return i;
>>> +
>>> + return -ENODEV;
>>> +}
>>> +
>>> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
>>> +{
>>> + struct atmel_lcdfb_power_ctrl_gpio *og;
>>> +
>>> + list_for_each_entry(og, &pdata->pwr_gpios, list)
>>> + gpio_set_value(og->gpio, on);
>>> +}
>>> +
>>> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
>>> +{
>>> + struct fb_info *info = sinfo->info;
>>> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>>> + struct fb_var_screeninfo *var = &info->var;
>>> + struct device *dev = &sinfo->pdev->dev;
>>> + struct device_node *np Þv->of_node;
>>> + struct device_node *display_np;
>>> + struct device_node *timings_np;
>>> + struct display_timings *timings;
>>> + enum of_gpio_flags flags;
>>> + struct atmel_lcdfb_power_ctrl_gpio *og;
>>> + bool is_gpio_power = false;
>>> + int ret = -ENOENT;
>>> + int i, gpio;
>>> +
>>> + sinfo->config = (struct atmel_lcdfb_config*)
>>> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
>>
>> Please split it in 2 steps, otherwise the day that the drivers doesn't
>> find the device in dt_ids table, it hangs here with an Oops.
> no as you will never end here in this case
Ok, I see.
>>
>>> +
>>> + display_np = of_parse_phandle(np, "display", 0);
>>> + if (!display_np) {
>>> + dev_err(dev, "failed to find display phandle\n");
>>> + return -ENOENT;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property bits-per-pixel\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property atmel,guard-time\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property bits-per-pixel\n");
>>
>> No, wrong error message.
>>
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = -ENOMEM;
>>> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
>>> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
>>> + i, &flags);
>>> + if (gpio < 0)
>>> + continue;
>>> +
>>> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
>>> + if (!og)
>>> + goto put_display_node;
>>> +
>>> + og->gpio = gpio;
>>> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
>>> + is_gpio_power = true;
>>> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
>>> + if (ret) {
>>> + dev_err(dev, "request gpio %d failed\n", gpio);
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = gpio_direction_output(gpio, og->active_low);
>>> + if (ret) {
>>> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
>>> + goto put_display_node;
>>> + }
>>> + }
>>> +
>>> + if (is_gpio_power)
>>> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
>>> +
>>> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
>>> + if (ret < 0) {
>>> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
>>> + goto put_display_node;
>>> + }
>>> + pdata->lcd_wiring_mode = ret;
>>> +
>>> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
>>> +
>>> + timings = of_get_display_timings(display_np);
>>> + if (!timings) {
>>> + dev_err(dev, "failed to get display timings\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + timings_np = of_find_node_by_name(display_np, "display-timings");
>>> + if (!timings_np) {
>>> + dev_err(dev, "failed to find display-timings node\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + for (i = 0; i < of_get_child_count(timings_np); i++) {
>>> + struct videomode vm;
>>> + struct fb_videomode fb_vm;
>>> +
>>> + ret = videomode_from_timing(timings, &vm, i);
>>> + if (ret < 0)
>>> + goto put_timings_node;
>>> + ret = fb_videomode_from_videomode(&vm, &fb_vm);
>>> + if (ret < 0)
>>> + goto put_timings_node;
>>> +
>>> + fb_add_videomode(&fb_vm, &info->modelist);
>>> + }
>>> +
>>> + return 0;
>>> +
>>> +put_timings_node:
>>> + of_node_put(timings_np);
>>> +put_display_node:
>>> + of_node_put(display_np);
>>> + return ret;
>>> +}
>>> +#else
>>> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
>>> +{
>>> + return 0;
>>> +}
>>> +#endif
>>>
>>> static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> {
>>> struct device *dev = &pdev->dev;
>>> struct fb_info *info;
>>> struct atmel_lcdfb_info *sinfo;
>>> - struct atmel_lcdfb_pdata *pdata;
>>> - struct fb_videomode fbmode;
>>> + struct atmel_lcdfb_pdata *pdata = NULL;
>>> struct resource *regs = NULL;
>>> struct resource *map = NULL;
>>> + struct fb_modelist *modelist;
>>> int ret;
>>>
>>> dev_dbg(dev, "%s BEGIN\n", __func__);
>>> @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> }
>>>
>>> sinfo = info->par;
>>> + sinfo->pdev = pdev;
>>> + sinfo->info = info;
>>> +
>>> + INIT_LIST_HEAD(&info->modelist);
>>>
>>> - if (dev->platform_data) {
>>> - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
>>> + if (pdev->dev.of_node) {
>>> + ret = atmel_lcdfb_of_init(sinfo);
>>> + if (ret)
>>> + goto free_info;
>>> + } else if (dev->platform_data) {
>>> + struct fb_monspecs *monspecs;
>>> + int i;
>>> +
>>> + pdata = dev->platform_data;
>>> + monspecs = pdata->default_monspecs;
>>> sinfo->pdata = *pdata;
>>> +
>>> + for (i = 0; i < monspecs->modedb_len; i++)
>>> + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
>>> +
>>> + sinfo->config = atmel_lcdfb_get_config(pdev);
>>> +
>>> + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
>>> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
>>> } else {
>>> dev_err(dev, "cannot get default configuration\n");
>>> goto free_info;
>>> }
>>> - sinfo->info = info;
>>> - sinfo->pdev = pdev;
>>> - sinfo->config = atmel_lcdfb_get_config(pdev);
>>> +
>>> if (!sinfo->config)
>>> goto free_info;
>>>
>>> @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> info->pseudo_palette = sinfo->pseudo_palette;
>>> info->fbops = &atmel_lcdfb_ops;
>>>
>>> - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
>>> info->fix = atmel_lcdfb_fix;
>>>
>>> /* Enable LCDC Clocks */
>>> @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> }
>>> atmel_lcdfb_start_clock(sinfo);
>>>
>>> - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
>>> - info->monspecs.modedb_len, info->monspecs.modedb,
>>> - pdata->default_bpp);
>>> - if (!ret) {
>>> - dev_err(dev, "no suitable video mode found\n");
>>> - goto stop_clk;
>>> - }
>>> + modelist = list_first_entry(&info->modelist,
>>> + struct fb_modelist, list);
>>> + fb_videomode_to_var(&info->var, &modelist->mode);
>>>
>>> + atmel_lcdfb_check_var(&info->var, info);
>>>
>>> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> if (!regs) {
>>> @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> goto unregister_irqs;
>>> }
>>>
>>> - /*
>>> - * This makes sure that our colour bitfield
>>> - * descriptors are correctly initialised.
>>> - */
>>> - atmel_lcdfb_check_var(&info->var, info);
>>> -
>>> - ret = fb_set_var(info, &info->var);
>>> - if (ret) {
>>> - dev_warn(dev, "unable to set display parameters\n");
>>> - goto free_cmap;
>>> - }
>>> -
>>> dev_set_drvdata(dev, info);
>>>
>>> /*
>>> @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> goto reset_drvdata;
>>> }
>>>
>>> - /* add selected videomode to modelist */
>>> - fb_var_to_videomode(&fbmode, &info->var);
>>> - fb_add_videomode(&fbmode, &info->modelist);
>>> -
>>> /* Power up the LCDC screen */
>>> atmel_lcdfb_power_control(sinfo, 1);
>>>
>>> @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>>
>>> reset_drvdata:
>>> dev_set_drvdata(dev, NULL);
>>> -free_cmap:
>>> fb_dealloc_cmap(&info->cmap);
>>> unregister_irqs:
>>> cancel_work_sync(&sinfo->task);
>>> @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
>>> .driver = {
>>> .name = "atmel_lcdfb",
>>> .owner = THIS_MODULE,
>>> + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
>>> },
>>> };
>>>
>>>
>>
>>
>> --
>> Nicolas Ferre
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-04-16 15:43 ` Nicolas Ferre
0 siblings, 0 replies; 91+ messages in thread
From: Nicolas Ferre @ 2013-04-16 15:43 UTC (permalink / raw)
To: linux-arm-kernel
On 04/16/2013 03:44 PM, Jean-Christophe PLAGNIOL-VILLARD :
> On 15:42 Tue 16 Apr , Nicolas Ferre wrote:
>> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
>>> get display timings from device tree
>>> Use videomode helpers to get display timings and configurations from
>>> device tree
>>
>> 2 sentences? Simply elaborate the 2nd one and it will be good.
>>
>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> Cc: linux-fbdev at vger.kernel.org
>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>> Cc: Andrew Morton <akpm@linux-foundation.org>
>>> ---
>>> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
>>> drivers/video/Kconfig | 2 +
>>> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
>>> 3 files changed, 289 insertions(+), 32 deletions(-)
>>> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>> new file mode 100644
>>> index 0000000..1ec175e
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
>>
>> Why lcdc? I would have preferred atmel,lcdfb, like the driver's name: it
>> is even more self-explanatory...
> we do not describe drivers but IP
fine, but in
static const struct platform_device_id atmel_lcdfb_devtypes, we use
"xxx-lcdfb" type...
>>
>>> @@ -0,0 +1,75 @@
>>> +Atmel LCDC Framebuffer
>>> +-----------------------------------------------------
>>> +
>>> +Required properties:
>>> +- compatible :
>>> + "atmel,at91sam9261-lcdc" ,
>>> + "atmel,at91sam9263-lcdc" ,
>>> + "atmel,at91sam9g10-lcdc" ,
>>> + "atmel,at91sam9g45-lcdc" ,
>>> + "atmel,at91sam9g45es-lcdc" ,
>>> + "atmel,at91sam9rl-lcdc" ,
>>> + "atmel,at32ap-lcdc"
>>> +- reg : Should contain 1 register ranges(address and length)
>>> +- interrupts : framebuffer controller interrupt
>>> +- display: a phandle pointing to the display node
>>> +
>>> +Required nodes:
>>> +- display: a display node is required to initialize the lcd panel
>>> + This should be in the board dts.
>>> +- default-mode: a videomode within the display with timing parameters
>>> + as specified below.
>>> +
>>> +Example:
>>> +
>>> + fb0: fb at 0x00500000 {
>>> + compatible = "atmel,at91sam9g45-lcdc";
>>> + reg = <0x00500000 0x1000>;
>>> + interrupts = <23 3 0>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pinctrl_fb>;
>>> + display = <&display0>;
>>> + status = "okay";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> +
>>> + };
>>> +
>>> +Atmel LCDC Display
>>> +-----------------------------------------------------
>>> +Required properties (as per of_videomode_helper):
>>
>> Can you please point somewhere to the documentation:
>> Documentation/devicetree/bindings/video/display-timing.txt
>>
>>> + - atmel,dmacon: dma controler configuration
>>
>> Typo: controller.
>>
>>> + - atmel,lcdcon2: lcd controler configuration
>>
>> Ditto
>>
>>> + - atmel,guard-time: lcd guard time (Delay in frame periods)
>>
>> periods -> period, no?
> no it's periods even in the datasheet
>>
>>> + - bits-per-pixel: lcd panel bit-depth.
>>> +
>>> +Optional properties (as per of_videomode_helper):
>>> + - atmel,lcdcon-backlight: enable backlight
>>> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
>>
>> Is it a sting, or a number (as seen below)? If it is a number, please
>> tell how to choose the index.
> String
Okay: so tell it in the description and correct the example below.
>>> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
>>> +
>>> +Example:
>>> + display0: display {
>>> + bits-per-pixel = <32>;
>>> + atmel,lcdcon-backlight;
>>> + atmel,dmacon = <0x1>;
>>> + atmel,lcdcon2 = <0x80008002>;
>>> + atmel,guard-time = <9>;
>>> + atmel,lcd-wiring-mode = <1>;
Here ----------------------------------^^^^
>>> +
>>> + display-timings {
>>> + native-mode = <&timing0>;
>>> + timing0: timing0 {
>>> + clock-frequency = <9000000>;
>>> + hactive = <480>;
>>> + vactive = <272>;
>>> + hback-porch = <1>;
>>> + hfront-porch = <1>;
>>> + vback-porch = <40>;
>>> + vfront-porch = <1>;
>>> + hsync-len = <45>;
>>> + vsync-len = <1>;
>>> + };
>>> + };
>>> + };
>>> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
>>> index 4c1546f..0687482 100644
>>> --- a/drivers/video/Kconfig
>>> +++ b/drivers/video/Kconfig
>>> @@ -1018,6 +1018,8 @@ config FB_ATMEL
>>> select FB_CFB_FILLRECT
>>> select FB_CFB_COPYAREA
>>> select FB_CFB_IMAGEBLIT
>>> + select FB_MODE_HELPERS
>>> + select OF_VIDEOMODE
>>> help
>>> This enables support for the AT91/AT32 LCD Controller.
>>>
>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>>> index f67e226..4a31570 100644
>>> --- a/drivers/video/atmel_lcdfb.c
>>> +++ b/drivers/video/atmel_lcdfb.c
>>> @@ -20,7 +20,11 @@
>>> #include <linux/gfp.h>
>>> #include <linux/module.h>
>>> #include <linux/platform_data/atmel.h>
>>> +#include <linux/of.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/of_gpio.h>
>>> #include <video/of_display_timing.h>
>>
>> As said in patch 1/8, this one belongs to this 4/8 patch.
>>
>>> +#include <video/videomode.h>
>>>
>>> #include <mach/cpu.h>
>>> #include <asm/gpio.h>
>>> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
>>> struct atmel_lcdfb_config *config;
>>> };
>>>
>>> +struct atmel_lcdfb_power_ctrl_gpio {
>>> + int gpio;
>>> + int active_low;
>>> +
>>> + struct list_head list;
>>> +};
>>> +
>>> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
>>> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>>>
>>> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
>>> clk_disable(sinfo->lcdc_clk);
>>> }
>>>
>>> +#ifdef CONFIG_OF
>>> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
>>> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
>>> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
>>> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
>>> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
>>> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
>>> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
>>> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
>>> + { /* sentinel */ }
>>> +};
>>> +
>>> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
>>> +
>>> +static const char *atmel_lcdfb_wiring_modes[] = {
>>> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
>>> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
>>> +};
>>> +
>>> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
>>> +{
>>> + const char *mode;
>>> + int err, i;
>>> +
>>> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
>>> + if (err < 0)
>>> + return ATMEL_LCDC_WIRING_BGR;
>>> +
>>> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
>>> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
>>> + return i;
>>> +
>>> + return -ENODEV;
>>> +}
>>> +
>>> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
>>> +{
>>> + struct atmel_lcdfb_power_ctrl_gpio *og;
>>> +
>>> + list_for_each_entry(og, &pdata->pwr_gpios, list)
>>> + gpio_set_value(og->gpio, on);
>>> +}
>>> +
>>> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
>>> +{
>>> + struct fb_info *info = sinfo->info;
>>> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
>>> + struct fb_var_screeninfo *var = &info->var;
>>> + struct device *dev = &sinfo->pdev->dev;
>>> + struct device_node *np =dev->of_node;
>>> + struct device_node *display_np;
>>> + struct device_node *timings_np;
>>> + struct display_timings *timings;
>>> + enum of_gpio_flags flags;
>>> + struct atmel_lcdfb_power_ctrl_gpio *og;
>>> + bool is_gpio_power = false;
>>> + int ret = -ENOENT;
>>> + int i, gpio;
>>> +
>>> + sinfo->config = (struct atmel_lcdfb_config*)
>>> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
>>
>> Please split it in 2 steps, otherwise the day that the drivers doesn't
>> find the device in dt_ids table, it hangs here with an Oops.
> no as you will never end here in this case
Ok, I see.
>>
>>> +
>>> + display_np = of_parse_phandle(np, "display", 0);
>>> + if (!display_np) {
>>> + dev_err(dev, "failed to find display phandle\n");
>>> + return -ENOENT;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property bits-per-pixel\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property atmel,guard-time\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
>>> + if (ret < 0) {
>>> + dev_err(dev, "failed to get property bits-per-pixel\n");
>>
>> No, wrong error message.
>>
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = -ENOMEM;
>>> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
>>> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
>>> + i, &flags);
>>> + if (gpio < 0)
>>> + continue;
>>> +
>>> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
>>> + if (!og)
>>> + goto put_display_node;
>>> +
>>> + og->gpio = gpio;
>>> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
>>> + is_gpio_power = true;
>>> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
>>> + if (ret) {
>>> + dev_err(dev, "request gpio %d failed\n", gpio);
>>> + goto put_display_node;
>>> + }
>>> +
>>> + ret = gpio_direction_output(gpio, og->active_low);
>>> + if (ret) {
>>> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
>>> + goto put_display_node;
>>> + }
>>> + }
>>> +
>>> + if (is_gpio_power)
>>> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
>>> +
>>> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
>>> + if (ret < 0) {
>>> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
>>> + goto put_display_node;
>>> + }
>>> + pdata->lcd_wiring_mode = ret;
>>> +
>>> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
>>> +
>>> + timings = of_get_display_timings(display_np);
>>> + if (!timings) {
>>> + dev_err(dev, "failed to get display timings\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + timings_np = of_find_node_by_name(display_np, "display-timings");
>>> + if (!timings_np) {
>>> + dev_err(dev, "failed to find display-timings node\n");
>>> + goto put_display_node;
>>> + }
>>> +
>>> + for (i = 0; i < of_get_child_count(timings_np); i++) {
>>> + struct videomode vm;
>>> + struct fb_videomode fb_vm;
>>> +
>>> + ret = videomode_from_timing(timings, &vm, i);
>>> + if (ret < 0)
>>> + goto put_timings_node;
>>> + ret = fb_videomode_from_videomode(&vm, &fb_vm);
>>> + if (ret < 0)
>>> + goto put_timings_node;
>>> +
>>> + fb_add_videomode(&fb_vm, &info->modelist);
>>> + }
>>> +
>>> + return 0;
>>> +
>>> +put_timings_node:
>>> + of_node_put(timings_np);
>>> +put_display_node:
>>> + of_node_put(display_np);
>>> + return ret;
>>> +}
>>> +#else
>>> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
>>> +{
>>> + return 0;
>>> +}
>>> +#endif
>>>
>>> static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> {
>>> struct device *dev = &pdev->dev;
>>> struct fb_info *info;
>>> struct atmel_lcdfb_info *sinfo;
>>> - struct atmel_lcdfb_pdata *pdata;
>>> - struct fb_videomode fbmode;
>>> + struct atmel_lcdfb_pdata *pdata = NULL;
>>> struct resource *regs = NULL;
>>> struct resource *map = NULL;
>>> + struct fb_modelist *modelist;
>>> int ret;
>>>
>>> dev_dbg(dev, "%s BEGIN\n", __func__);
>>> @@ -967,17 +1149,35 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> }
>>>
>>> sinfo = info->par;
>>> + sinfo->pdev = pdev;
>>> + sinfo->info = info;
>>> +
>>> + INIT_LIST_HEAD(&info->modelist);
>>>
>>> - if (dev->platform_data) {
>>> - pdata = (struct atmel_lcdfb_pdata *)dev->platform_data;
>>> + if (pdev->dev.of_node) {
>>> + ret = atmel_lcdfb_of_init(sinfo);
>>> + if (ret)
>>> + goto free_info;
>>> + } else if (dev->platform_data) {
>>> + struct fb_monspecs *monspecs;
>>> + int i;
>>> +
>>> + pdata = dev->platform_data;
>>> + monspecs = pdata->default_monspecs;
>>> sinfo->pdata = *pdata;
>>> +
>>> + for (i = 0; i < monspecs->modedb_len; i++)
>>> + fb_add_videomode(&monspecs->modedb[i], &info->modelist);
>>> +
>>> + sinfo->config = atmel_lcdfb_get_config(pdev);
>>> +
>>> + info->var.bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
>>> + memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
>>> } else {
>>> dev_err(dev, "cannot get default configuration\n");
>>> goto free_info;
>>> }
>>> - sinfo->info = info;
>>> - sinfo->pdev = pdev;
>>> - sinfo->config = atmel_lcdfb_get_config(pdev);
>>> +
>>> if (!sinfo->config)
>>> goto free_info;
>>>
>>> @@ -986,7 +1186,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> info->pseudo_palette = sinfo->pseudo_palette;
>>> info->fbops = &atmel_lcdfb_ops;
>>>
>>> - memcpy(&info->monspecs, pdata->default_monspecs, sizeof(info->monspecs));
>>> info->fix = atmel_lcdfb_fix;
>>>
>>> /* Enable LCDC Clocks */
>>> @@ -1002,14 +1201,11 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> }
>>> atmel_lcdfb_start_clock(sinfo);
>>>
>>> - ret = fb_find_mode(&info->var, info, NULL, info->monspecs.modedb,
>>> - info->monspecs.modedb_len, info->monspecs.modedb,
>>> - pdata->default_bpp);
>>> - if (!ret) {
>>> - dev_err(dev, "no suitable video mode found\n");
>>> - goto stop_clk;
>>> - }
>>> + modelist = list_first_entry(&info->modelist,
>>> + struct fb_modelist, list);
>>> + fb_videomode_to_var(&info->var, &modelist->mode);
>>>
>>> + atmel_lcdfb_check_var(&info->var, info);
>>>
>>> regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>>> if (!regs) {
>>> @@ -1093,18 +1289,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> goto unregister_irqs;
>>> }
>>>
>>> - /*
>>> - * This makes sure that our colour bitfield
>>> - * descriptors are correctly initialised.
>>> - */
>>> - atmel_lcdfb_check_var(&info->var, info);
>>> -
>>> - ret = fb_set_var(info, &info->var);
>>> - if (ret) {
>>> - dev_warn(dev, "unable to set display parameters\n");
>>> - goto free_cmap;
>>> - }
>>> -
>>> dev_set_drvdata(dev, info);
>>>
>>> /*
>>> @@ -1116,10 +1300,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>> goto reset_drvdata;
>>> }
>>>
>>> - /* add selected videomode to modelist */
>>> - fb_var_to_videomode(&fbmode, &info->var);
>>> - fb_add_videomode(&fbmode, &info->modelist);
>>> -
>>> /* Power up the LCDC screen */
>>> atmel_lcdfb_power_control(sinfo, 1);
>>>
>>> @@ -1130,7 +1310,6 @@ static int __init atmel_lcdfb_probe(struct platform_device *pdev)
>>>
>>> reset_drvdata:
>>> dev_set_drvdata(dev, NULL);
>>> -free_cmap:
>>> fb_dealloc_cmap(&info->cmap);
>>> unregister_irqs:
>>> cancel_work_sync(&sinfo->task);
>>> @@ -1249,6 +1428,7 @@ static struct platform_driver atmel_lcdfb_driver = {
>>> .driver = {
>>> .name = "atmel_lcdfb",
>>> .owner = THIS_MODULE,
>>> + .of_match_table = of_match_ptr(atmel_lcdfb_dt_ids),
>>> },
>>> };
>>>
>>>
>>
>>
>> --
>> Nicolas Ferre
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 6/8] ARM: at91: sam9263: add fb dt support
2013-04-16 15:11 ` Nicolas Ferre
@ 2013-04-16 15:48 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 15:48 UTC (permalink / raw)
To: Nicolas Ferre; +Cc: devicetree-discuss, linux-arm-kernel
On 17:11 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/16/2013 04:13 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > On 16:11 Tue 16 Apr , Nicolas Ferre wrote:
> >> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> >>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >>> ---
> >>> arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
> >>> 1 file changed, 39 insertions(+)
> >>>
> >>> diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
> >>> index 271d4de..3d0effa 100644
> >>> --- a/arch/arm/boot/dts/at91sam9263.dtsi
> >>> +++ b/arch/arm/boot/dts/at91sam9263.dtsi
> >>> @@ -303,6 +303,34 @@
> >>> };
> >>> };
> >>>
> >>> + fb {
> >>> + pinctrl_fb: fb-0 {
> >>> + atmel,pins =
> >>> + <2 1 0x1 0x0 /* PC1 periph A */
> >>> + 2 2 0x1 0x0 /* PC2 periph A */
> >>> + 2 3 0x1 0x0 /* PC3 periph A */
> >>> + 1 9 0x2 0x0 /* PB9 periph B */
> >>> + 2 6 0x1 0x0 /* PC6 periph A */
> >>> + 2 7 0x1 0x0 /* PC7 periph A */
> >>> + 2 8 0x1 0x0 /* PC8 periph A */
> >>> + 2 9 0x1 0x0 /* PC9 periph A */
> >>> + 2 10 0x1 0x0 /* PC10 periph A */
> >>> + 2 11 0x1 0x0 /* PC11 periph A */
> >>> + 2 14 0x1 0x0 /* PC14 periph A */
> >>> + 2 15 0x1 0x0 /* PC15 periph A */
> >>> + 2 16 0x1 0x0 /* PC16 periph A */
> >>> + 2 12 0x2 0x0 /* PC12 periph B */
> >>> + 2 18 0x1 0x0 /* PC18 periph A */
> >>> + 2 19 0x1 0x0 /* PC19 periph A */
> >>> + 2 22 0x1 0x0 /* PC22 periph A */
> >>> + 2 23 0x1 0x0 /* PC23 periph A */
> >>> + 2 24 0x1 0x0 /* PC24 periph A */
> >>> + 2 17 0x2 0x0 /* PC17 periph B */
> >>> + 2 26 0x1 0x0 /* PC26 periph A */
> >>> + 2 27 0x1 0x0>; /* PC27 periph A */
> >>
> >> Verified, okay.
> >>
> >>> + };
> >>> + };
> >>> +
> >>> pioA: gpio@fffff200 {
> >>> compatible = "atmel,at91rm9200-gpio";
> >>> reg = <0xfffff200 0x200>;
> >>> @@ -464,6 +492,17 @@
> >>> };
> >>> };
> >>>
> >>> + fb0: fb@0x00500000 {
> >>
> >> No, it is 0x700000
> >>
> >>> + compatible = "atmel,at91sam9263-lcdc";
> >>> + reg = <0x00700000 0x1000>;
> >>
> >> Ditto.
> >>
> >>> + interrupts = <26 3 0>;
> >>
> >> <26 4 0> here.
> > no lcd is 3 even in c
> >
> > and even 3 could be slow in some big lcd case
>
> No, you mean the priority, but priority is encoded as the 3rd cell. So,
> we end up with:
>
> <26 4 3>
>
> (I agree with the 3)
I hate those magic number
so this is the las patch to go in with as soon as the macro for dts are in I
free the at91 dts and switch to it
>
>
> >>
> >>
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&pinctrl_fb>;
> >>> + status = "disabled";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>
> >> Ditto in 9g45 case.
> >>
> >>> + };
> >>> +
> >>> nand0: nand@40000000 {
> >>> compatible = "atmel,at91rm9200-nand";
> >>> #address-cells = <1>;
> >>>
> >>
> >>
> >> --
> >> Nicolas Ferre
> >
>
> Bye,
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 6/8] ARM: at91: sam9263: add fb dt support
@ 2013-04-16 15:48 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-04-16 15:48 UTC (permalink / raw)
To: linux-arm-kernel
On 17:11 Tue 16 Apr , Nicolas Ferre wrote:
> On 04/16/2013 04:13 PM, Jean-Christophe PLAGNIOL-VILLARD :
> > On 16:11 Tue 16 Apr , Nicolas Ferre wrote:
> >> On 04/11/2013 05:00 PM, Jean-Christophe PLAGNIOL-VILLARD :
> >>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >>> ---
> >>> arch/arm/boot/dts/at91sam9263.dtsi | 39 ++++++++++++++++++++++++++++++++++++
> >>> 1 file changed, 39 insertions(+)
> >>>
> >>> diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
> >>> index 271d4de..3d0effa 100644
> >>> --- a/arch/arm/boot/dts/at91sam9263.dtsi
> >>> +++ b/arch/arm/boot/dts/at91sam9263.dtsi
> >>> @@ -303,6 +303,34 @@
> >>> };
> >>> };
> >>>
> >>> + fb {
> >>> + pinctrl_fb: fb-0 {
> >>> + atmel,pins =
> >>> + <2 1 0x1 0x0 /* PC1 periph A */
> >>> + 2 2 0x1 0x0 /* PC2 periph A */
> >>> + 2 3 0x1 0x0 /* PC3 periph A */
> >>> + 1 9 0x2 0x0 /* PB9 periph B */
> >>> + 2 6 0x1 0x0 /* PC6 periph A */
> >>> + 2 7 0x1 0x0 /* PC7 periph A */
> >>> + 2 8 0x1 0x0 /* PC8 periph A */
> >>> + 2 9 0x1 0x0 /* PC9 periph A */
> >>> + 2 10 0x1 0x0 /* PC10 periph A */
> >>> + 2 11 0x1 0x0 /* PC11 periph A */
> >>> + 2 14 0x1 0x0 /* PC14 periph A */
> >>> + 2 15 0x1 0x0 /* PC15 periph A */
> >>> + 2 16 0x1 0x0 /* PC16 periph A */
> >>> + 2 12 0x2 0x0 /* PC12 periph B */
> >>> + 2 18 0x1 0x0 /* PC18 periph A */
> >>> + 2 19 0x1 0x0 /* PC19 periph A */
> >>> + 2 22 0x1 0x0 /* PC22 periph A */
> >>> + 2 23 0x1 0x0 /* PC23 periph A */
> >>> + 2 24 0x1 0x0 /* PC24 periph A */
> >>> + 2 17 0x2 0x0 /* PC17 periph B */
> >>> + 2 26 0x1 0x0 /* PC26 periph A */
> >>> + 2 27 0x1 0x0>; /* PC27 periph A */
> >>
> >> Verified, okay.
> >>
> >>> + };
> >>> + };
> >>> +
> >>> pioA: gpio at fffff200 {
> >>> compatible = "atmel,at91rm9200-gpio";
> >>> reg = <0xfffff200 0x200>;
> >>> @@ -464,6 +492,17 @@
> >>> };
> >>> };
> >>>
> >>> + fb0: fb at 0x00500000 {
> >>
> >> No, it is 0x700000
> >>
> >>> + compatible = "atmel,at91sam9263-lcdc";
> >>> + reg = <0x00700000 0x1000>;
> >>
> >> Ditto.
> >>
> >>> + interrupts = <26 3 0>;
> >>
> >> <26 4 0> here.
> > no lcd is 3 even in c
> >
> > and even 3 could be slow in some big lcd case
>
> No, you mean the priority, but priority is encoded as the 3rd cell. So,
> we end up with:
>
> <26 4 3>
>
> (I agree with the 3)
I hate those magic number
so this is the las patch to go in with as soon as the macro for dts are in I
free the at91 dts and switch to it
>
>
> >>
> >>
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&pinctrl_fb>;
> >>> + status = "disabled";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <1>;
> >>
> >> Ditto in 9g45 case.
> >>
> >>> + };
> >>> +
> >>> nand0: nand at 40000000 {
> >>> compatible = "atmel,at91rm9200-nand";
> >>> #address-cells = <1>;
> >>>
> >>
> >>
> >> --
> >> Nicolas Ferre
> >
>
> Bye,
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-05-29 14:36 ` Richard Genoud
-1 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 14:36 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andreas Bießmann,
Andrew Morton, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Hans-Christian Egtvedt
2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
> Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
> Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
> Cc: Hans-Christian Egtvedt <egtvedt-BrfabpQBY5qlHtIdYg32fQ@public.gmane.org>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
>
[snip]
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index c1a2914..98733cd4 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,12 +20,45 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <video/of_display_timing.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
>
> #include <video/atmel_lcdc.h>
>
> +struct atmel_lcdfb_config {
> + bool have_alt_pixclock;
> + bool have_hozval;
> + bool have_intensity_bit;
> +};
> +
> + /* LCD Controller info data structure, stored in device platform_data */
> +struct atmel_lcdfb_info {
> + spinlock_t lock;
> + struct fb_info *info;
> + void __iomem *mmio;
> + int irq_base;
> + struct work_struct task;
> +
> + unsigned int smem_len;
> + struct platform_device *pdev;
> + struct clk *bus_clk;
> + struct clk *lcdc_clk;
> +
> + struct backlight_device *backlight;
> + u8 bl_power;
> + bool lcdcon_pol_negative;
I think lcdcon_pol_negative should be part of pdata, because it really
depends on how the PWM is wired on the board.
Regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 14:36 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 14:36 UTC (permalink / raw)
To: linux-arm-kernel
2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
>
[snip]
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index c1a2914..98733cd4 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,12 +20,45 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <video/of_display_timing.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
>
> #include <video/atmel_lcdc.h>
>
> +struct atmel_lcdfb_config {
> + bool have_alt_pixclock;
> + bool have_hozval;
> + bool have_intensity_bit;
> +};
> +
> + /* LCD Controller info data structure, stored in device platform_data */
> +struct atmel_lcdfb_info {
> + spinlock_t lock;
> + struct fb_info *info;
> + void __iomem *mmio;
> + int irq_base;
> + struct work_struct task;
> +
> + unsigned int smem_len;
> + struct platform_device *pdev;
> + struct clk *bus_clk;
> + struct clk *lcdc_clk;
> +
> + struct backlight_device *backlight;
> + u8 bl_power;
> + bool lcdcon_pol_negative;
I think lcdcon_pol_negative should be part of pdata, because it really
depends on how the PWM is wired on the board.
Regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 14:36 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 14:36 UTC (permalink / raw)
To: linux-arm-kernel
2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> ---
> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> arch/arm/mach-at91/board.h | 4 +-
> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> arch/avr32/boards/atstk1000/setup.c | 2 +-
> arch/avr32/boards/favr-32/setup.c | 2 +-
> arch/avr32/boards/hammerhead/setup.c | 2 +-
> arch/avr32/boards/merisc/display.c | 2 +-
> arch/avr32/boards/mimc200/setup.c | 4 +-
> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> include/video/atmel_lcdc.h | 24 +------
> 21 files changed, 109 insertions(+), 101 deletions(-)
>
[snip]
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index c1a2914..98733cd4 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,12 +20,45 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <video/of_display_timing.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
>
> #include <video/atmel_lcdc.h>
>
> +struct atmel_lcdfb_config {
> + bool have_alt_pixclock;
> + bool have_hozval;
> + bool have_intensity_bit;
> +};
> +
> + /* LCD Controller info data structure, stored in device platform_data */
> +struct atmel_lcdfb_info {
> + spinlock_t lock;
> + struct fb_info *info;
> + void __iomem *mmio;
> + int irq_base;
> + struct work_struct task;
> +
> + unsigned int smem_len;
> + struct platform_device *pdev;
> + struct clk *bus_clk;
> + struct clk *lcdc_clk;
> +
> + struct backlight_device *backlight;
> + u8 bl_power;
> + bool lcdcon_pol_negative;
I think lcdcon_pol_negative should be part of pdata, because it really
depends on how the PWM is wired on the board.
Regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-05-29 15:01 ` Richard Genoud
-1 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 15:01 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andreas Bießmann,
Andrew Morton, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
> get display timings from device tree
> Use videomode helpers to get display timings and configurations from
> device tree
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
> Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
> Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
> ---
> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> drivers/video/Kconfig | 2 +
> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> 3 files changed, 289 insertions(+), 32 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> new file mode 100644
> index 0000000..1ec175e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> @@ -0,0 +1,75 @@
> +Atmel LCDC Framebuffer
> +-----------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + "atmel,at91sam9261-lcdc" ,
> + "atmel,at91sam9263-lcdc" ,
> + "atmel,at91sam9g10-lcdc" ,
> + "atmel,at91sam9g45-lcdc" ,
> + "atmel,at91sam9g45es-lcdc" ,
> + "atmel,at91sam9rl-lcdc" ,
> + "atmel,at32ap-lcdc"
> +- reg : Should contain 1 register ranges(address and length)
> +- interrupts : framebuffer controller interrupt
> +- display: a phandle pointing to the display node
> +
> +Required nodes:
> +- display: a display node is required to initialize the lcd panel
> + This should be in the board dts.
> +- default-mode: a videomode within the display with timing parameters
> + as specified below.
> +
> +Example:
> +
> + fb0: fb@0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + display = <&display0>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + };
> +
> +Atmel LCDC Display
> +-----------------------------------------------------
> +Required properties (as per of_videomode_helper):
> +
> + - atmel,dmacon: dma controler configuration
> + - atmel,lcdcon2: lcd controler configuration
> + - atmel,guard-time: lcd guard time (Delay in frame periods)
> + - bits-per-pixel: lcd panel bit-depth.
> +
> +Optional properties (as per of_videomode_helper):
> + - atmel,lcdcon-backlight: enable backlight
> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
still on lcdcon_pol_negative, we can add something like that:
- atmel,lcdcon-pwm-pulse-low: Output PWM pulses are low level (high
level if not set)
> +
> +Example:
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 4c1546f..0687482 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1018,6 +1018,8 @@ config FB_ATMEL
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select FB_MODE_HELPERS
> + select OF_VIDEOMODE
> help
> This enables support for the AT91/AT32 LCD Controller.
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index f67e226..4a31570 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,7 +20,11 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <video/of_display_timing.h>
> +#include <video/videomode.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> struct atmel_lcdfb_config *config;
> };
>
> +struct atmel_lcdfb_power_ctrl_gpio {
> + int gpio;
> + int active_low;
> +
> + struct list_head list;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> clk_disable(sinfo->lcdc_clk);
> }
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> +
> +static const char *atmel_lcdfb_wiring_modes[] = {
> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> +};
> +
> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> +{
> + const char *mode;
> + int err, i;
> +
> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> + if (err < 0)
> + return ATMEL_LCDC_WIRING_BGR;
> +
> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> + return i;
> +
> + return -ENODEV;
> +}
> +
> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> +{
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> +
> + list_for_each_entry(og, &pdata->pwr_gpios, list)
> + gpio_set_value(og->gpio, on);
> +}
> +
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + struct fb_info *info = sinfo->info;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> + struct fb_var_screeninfo *var = &info->var;
> + struct device *dev = &sinfo->pdev->dev;
> + struct device_node *np =dev->of_node;
> + struct device_node *display_np;
> + struct device_node *timings_np;
> + struct display_timings *timings;
> + enum of_gpio_flags flags;
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> + bool is_gpio_power = false;
> + int ret = -ENOENT;
> + int i, gpio;
> +
> + sinfo->config = (struct atmel_lcdfb_config*)
> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
> +
> + display_np = of_parse_phandle(np, "display", 0);
> + if (!display_np) {
> + dev_err(dev, "failed to find display phandle\n");
> + return -ENOENT;
> + }
> +
> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,guard-time\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = -ENOMEM;
> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> + i, &flags);
> + if (gpio < 0)
> + continue;
> +
> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> + if (!og)
> + goto put_display_node;
> +
> + og->gpio = gpio;
> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> + is_gpio_power = true;
> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> + if (ret) {
> + dev_err(dev, "request gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> +
> + ret = gpio_direction_output(gpio, og->active_low);
> + if (ret) {
> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> + }
> +
> + if (is_gpio_power)
> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> +
> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> + if (ret < 0) {
> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> + goto put_display_node;
> + }
> + pdata->lcd_wiring_mode = ret;
> +
> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
and here, something like:
pdata->lcdcon_pol_negative = of_property_read_bool(display_np,
"atmel,lcdcon-pwm-pulse-low");
would be nice
Regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-05-29 15:01 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 15:01 UTC (permalink / raw)
To: linux-arm-kernel
2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> get display timings from device tree
> Use videomode helpers to get display timings and configurations from
> device tree
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev@vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> drivers/video/Kconfig | 2 +
> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> 3 files changed, 289 insertions(+), 32 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> new file mode 100644
> index 0000000..1ec175e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> @@ -0,0 +1,75 @@
> +Atmel LCDC Framebuffer
> +-----------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + "atmel,at91sam9261-lcdc" ,
> + "atmel,at91sam9263-lcdc" ,
> + "atmel,at91sam9g10-lcdc" ,
> + "atmel,at91sam9g45-lcdc" ,
> + "atmel,at91sam9g45es-lcdc" ,
> + "atmel,at91sam9rl-lcdc" ,
> + "atmel,at32ap-lcdc"
> +- reg : Should contain 1 register ranges(address and length)
> +- interrupts : framebuffer controller interrupt
> +- display: a phandle pointing to the display node
> +
> +Required nodes:
> +- display: a display node is required to initialize the lcd panel
> + This should be in the board dts.
> +- default-mode: a videomode within the display with timing parameters
> + as specified below.
> +
> +Example:
> +
> + fb0: fb@0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + display = <&display0>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + };
> +
> +Atmel LCDC Display
> +-----------------------------------------------------
> +Required properties (as per of_videomode_helper):
> +
> + - atmel,dmacon: dma controler configuration
> + - atmel,lcdcon2: lcd controler configuration
> + - atmel,guard-time: lcd guard time (Delay in frame periods)
> + - bits-per-pixel: lcd panel bit-depth.
> +
> +Optional properties (as per of_videomode_helper):
> + - atmel,lcdcon-backlight: enable backlight
> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
still on lcdcon_pol_negative, we can add something like that:
- atmel,lcdcon-pwm-pulse-low: Output PWM pulses are low level (high
level if not set)
> +
> +Example:
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 4c1546f..0687482 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1018,6 +1018,8 @@ config FB_ATMEL
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select FB_MODE_HELPERS
> + select OF_VIDEOMODE
> help
> This enables support for the AT91/AT32 LCD Controller.
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index f67e226..4a31570 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,7 +20,11 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <video/of_display_timing.h>
> +#include <video/videomode.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> struct atmel_lcdfb_config *config;
> };
>
> +struct atmel_lcdfb_power_ctrl_gpio {
> + int gpio;
> + int active_low;
> +
> + struct list_head list;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> clk_disable(sinfo->lcdc_clk);
> }
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> +
> +static const char *atmel_lcdfb_wiring_modes[] = {
> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> +};
> +
> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> +{
> + const char *mode;
> + int err, i;
> +
> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> + if (err < 0)
> + return ATMEL_LCDC_WIRING_BGR;
> +
> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> + return i;
> +
> + return -ENODEV;
> +}
> +
> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> +{
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> +
> + list_for_each_entry(og, &pdata->pwr_gpios, list)
> + gpio_set_value(og->gpio, on);
> +}
> +
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + struct fb_info *info = sinfo->info;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> + struct fb_var_screeninfo *var = &info->var;
> + struct device *dev = &sinfo->pdev->dev;
> + struct device_node *np Þv->of_node;
> + struct device_node *display_np;
> + struct device_node *timings_np;
> + struct display_timings *timings;
> + enum of_gpio_flags flags;
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> + bool is_gpio_power = false;
> + int ret = -ENOENT;
> + int i, gpio;
> +
> + sinfo->config = (struct atmel_lcdfb_config*)
> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
> +
> + display_np = of_parse_phandle(np, "display", 0);
> + if (!display_np) {
> + dev_err(dev, "failed to find display phandle\n");
> + return -ENOENT;
> + }
> +
> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,guard-time\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = -ENOMEM;
> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> + i, &flags);
> + if (gpio < 0)
> + continue;
> +
> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> + if (!og)
> + goto put_display_node;
> +
> + og->gpio = gpio;
> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> + is_gpio_power = true;
> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> + if (ret) {
> + dev_err(dev, "request gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> +
> + ret = gpio_direction_output(gpio, og->active_low);
> + if (ret) {
> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> + }
> +
> + if (is_gpio_power)
> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> +
> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> + if (ret < 0) {
> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> + goto put_display_node;
> + }
> + pdata->lcd_wiring_mode = ret;
> +
> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
and here, something like:
pdata->lcdcon_pol_negative = of_property_read_bool(display_np,
"atmel,lcdcon-pwm-pulse-low");
would be nice
Regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 4/8] video: atmel_lcdfb: add device tree suport
@ 2013-05-29 15:01 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 15:01 UTC (permalink / raw)
To: linux-arm-kernel
2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> get display timings from device tree
> Use videomode helpers to get display timings and configurations from
> device tree
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: linux-fbdev at vger.kernel.org
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> ---
> .../devicetree/bindings/video/atmel,lcdc.txt | 75 ++++++
> drivers/video/Kconfig | 2 +
> drivers/video/atmel_lcdfb.c | 244 +++++++++++++++++---
> 3 files changed, 289 insertions(+), 32 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/video/atmel,lcdc.txt
>
> diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> new file mode 100644
> index 0000000..1ec175e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt
> @@ -0,0 +1,75 @@
> +Atmel LCDC Framebuffer
> +-----------------------------------------------------
> +
> +Required properties:
> +- compatible :
> + "atmel,at91sam9261-lcdc" ,
> + "atmel,at91sam9263-lcdc" ,
> + "atmel,at91sam9g10-lcdc" ,
> + "atmel,at91sam9g45-lcdc" ,
> + "atmel,at91sam9g45es-lcdc" ,
> + "atmel,at91sam9rl-lcdc" ,
> + "atmel,at32ap-lcdc"
> +- reg : Should contain 1 register ranges(address and length)
> +- interrupts : framebuffer controller interrupt
> +- display: a phandle pointing to the display node
> +
> +Required nodes:
> +- display: a display node is required to initialize the lcd panel
> + This should be in the board dts.
> +- default-mode: a videomode within the display with timing parameters
> + as specified below.
> +
> +Example:
> +
> + fb0: fb at 0x00500000 {
> + compatible = "atmel,at91sam9g45-lcdc";
> + reg = <0x00500000 0x1000>;
> + interrupts = <23 3 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fb>;
> + display = <&display0>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + };
> +
> +Atmel LCDC Display
> +-----------------------------------------------------
> +Required properties (as per of_videomode_helper):
> +
> + - atmel,dmacon: dma controler configuration
> + - atmel,lcdcon2: lcd controler configuration
> + - atmel,guard-time: lcd guard time (Delay in frame periods)
> + - bits-per-pixel: lcd panel bit-depth.
> +
> +Optional properties (as per of_videomode_helper):
> + - atmel,lcdcon-backlight: enable backlight
> + - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
> + - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
still on lcdcon_pol_negative, we can add something like that:
- atmel,lcdcon-pwm-pulse-low: Output PWM pulses are low level (high
level if not set)
> +
> +Example:
> + display0: display {
> + bits-per-pixel = <32>;
> + atmel,lcdcon-backlight;
> + atmel,dmacon = <0x1>;
> + atmel,lcdcon2 = <0x80008002>;
> + atmel,guard-time = <9>;
> + atmel,lcd-wiring-mode = <1>;
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: timing0 {
> + clock-frequency = <9000000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <1>;
> + hfront-porch = <1>;
> + vback-porch = <40>;
> + vfront-porch = <1>;
> + hsync-len = <45>;
> + vsync-len = <1>;
> + };
> + };
> + };
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 4c1546f..0687482 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1018,6 +1018,8 @@ config FB_ATMEL
> select FB_CFB_FILLRECT
> select FB_CFB_COPYAREA
> select FB_CFB_IMAGEBLIT
> + select FB_MODE_HELPERS
> + select OF_VIDEOMODE
> help
> This enables support for the AT91/AT32 LCD Controller.
>
> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> index f67e226..4a31570 100644
> --- a/drivers/video/atmel_lcdfb.c
> +++ b/drivers/video/atmel_lcdfb.c
> @@ -20,7 +20,11 @@
> #include <linux/gfp.h>
> #include <linux/module.h>
> #include <linux/platform_data/atmel.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> #include <video/of_display_timing.h>
> +#include <video/videomode.h>
>
> #include <mach/cpu.h>
> #include <asm/gpio.h>
> @@ -59,6 +63,13 @@ struct atmel_lcdfb_info {
> struct atmel_lcdfb_config *config;
> };
>
> +struct atmel_lcdfb_power_ctrl_gpio {
> + int gpio;
> + int active_low;
> +
> + struct list_head list;
> +};
> +
> #define lcdc_readl(sinfo, reg) __raw_readl((sinfo)->mmio+(reg))
> #define lcdc_writel(sinfo, reg, val) __raw_writel((val), (sinfo)->mmio+(reg))
>
> @@ -945,16 +956,187 @@ static void atmel_lcdfb_stop_clock(struct atmel_lcdfb_info *sinfo)
> clk_disable(sinfo->lcdc_clk);
> }
>
> +#ifdef CONFIG_OF
> +static const struct of_device_id atmel_lcdfb_dt_ids[] = {
> + { .compatible = "atmel,at91sam9261-lcdc" , .data = &at91sam9261_config, },
> + { .compatible = "atmel,at91sam9263-lcdc" , .data = &at91sam9263_config, },
> + { .compatible = "atmel,at91sam9g10-lcdc" , .data = &at91sam9g10_config, },
> + { .compatible = "atmel,at91sam9g45-lcdc" , .data = &at91sam9g45_config, },
> + { .compatible = "atmel,at91sam9g45es-lcdc" , .data = &at91sam9g45es_config, },
> + { .compatible = "atmel,at91sam9rl-lcdc" , .data = &at91sam9rl_config, },
> + { .compatible = "atmel,at32ap-lcdc" , .data = &at32ap_config, },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_lcdfb_dt_ids);
> +
> +static const char *atmel_lcdfb_wiring_modes[] = {
> + [ATMEL_LCDC_WIRING_BGR] = "BRG",
> + [ATMEL_LCDC_WIRING_RGB] = "RGB",
> +};
> +
> +const int atmel_lcdfb_get_of_wiring_modes(struct device_node *np)
> +{
> + const char *mode;
> + int err, i;
> +
> + err = of_property_read_string(np, "atmel,lcd-wiring-mode", &mode);
> + if (err < 0)
> + return ATMEL_LCDC_WIRING_BGR;
> +
> + for (i = 0; i < ARRAY_SIZE(atmel_lcdfb_wiring_modes); i++)
> + if (!strcasecmp(mode, atmel_lcdfb_wiring_modes[i]))
> + return i;
> +
> + return -ENODEV;
> +}
> +
> +static void atmel_lcdfb_power_control_gpio(struct atmel_lcdfb_pdata *pdata, int on)
> +{
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> +
> + list_for_each_entry(og, &pdata->pwr_gpios, list)
> + gpio_set_value(og->gpio, on);
> +}
> +
> +static int atmel_lcdfb_of_init(struct atmel_lcdfb_info *sinfo)
> +{
> + struct fb_info *info = sinfo->info;
> + struct atmel_lcdfb_pdata *pdata = &sinfo->pdata;
> + struct fb_var_screeninfo *var = &info->var;
> + struct device *dev = &sinfo->pdev->dev;
> + struct device_node *np =dev->of_node;
> + struct device_node *display_np;
> + struct device_node *timings_np;
> + struct display_timings *timings;
> + enum of_gpio_flags flags;
> + struct atmel_lcdfb_power_ctrl_gpio *og;
> + bool is_gpio_power = false;
> + int ret = -ENOENT;
> + int i, gpio;
> +
> + sinfo->config = (struct atmel_lcdfb_config*)
> + of_match_device(atmel_lcdfb_dt_ids, dev)->data;
> +
> + display_np = of_parse_phandle(np, "display", 0);
> + if (!display_np) {
> + dev_err(dev, "failed to find display phandle\n");
> + return -ENOENT;
> + }
> +
> + ret = of_property_read_u32(display_np, "bits-per-pixel", &var->bits_per_pixel);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,guard-time", &pdata->guard_time);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,guard-time\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,lcdcon2", &pdata->default_lcdcon2);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property atmel,lcdcon2\n");
> + goto put_display_node;
> + }
> +
> + ret = of_property_read_u32(display_np, "atmel,dmacon", &pdata->default_dmacon);
> + if (ret < 0) {
> + dev_err(dev, "failed to get property bits-per-pixel\n");
> + goto put_display_node;
> + }
> +
> + ret = -ENOMEM;
> + for (i = 0; i < of_gpio_named_count(display_np, "atmel,power-control-gpio"); i++) {
> + gpio = of_get_named_gpio_flags(display_np, "atmel,power-control-gpio",
> + i, &flags);
> + if (gpio < 0)
> + continue;
> +
> + og = devm_kzalloc(dev, sizeof(*og), GFP_KERNEL);
> + if (!og)
> + goto put_display_node;
> +
> + og->gpio = gpio;
> + og->active_low = flags & OF_GPIO_ACTIVE_LOW;
> + is_gpio_power = true;
> + ret = devm_gpio_request(dev, gpio, "lcd-power-control-gpio");
> + if (ret) {
> + dev_err(dev, "request gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> +
> + ret = gpio_direction_output(gpio, og->active_low);
> + if (ret) {
> + dev_err(dev, "set direction output gpio %d failed\n", gpio);
> + goto put_display_node;
> + }
> + }
> +
> + if (is_gpio_power)
> + pdata->atmel_lcdfb_power_control = atmel_lcdfb_power_control_gpio;
> +
> + ret = atmel_lcdfb_get_of_wiring_modes(display_np);
> + if (ret < 0) {
> + dev_err(dev, "invalid atmel,lcd-wiring-mode\n");
> + goto put_display_node;
> + }
> + pdata->lcd_wiring_mode = ret;
> +
> + pdata->lcdcon_is_backlight = of_property_read_bool(display_np, "atmel,lcdcon-backlight");
and here, something like:
pdata->lcdcon_pol_negative = of_property_read_bool(display_np,
"atmel,lcdcon-pwm-pulse-low");
would be nice
Regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-29 14:36 ` Richard Genoud
(?)
@ 2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-29 17:35 UTC (permalink / raw)
To: Richard Genoud
Cc: linux-fbdev, devicetree-discuss, Nicolas Ferre,
Andreas Bießmann, Andrew Morton, linux-arm-kernel,
Hans-Christian Egtvedt
On 16:36 Wed 29 May , Richard Genoud wrote:
> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: linux-fbdev@vger.kernel.org
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Andrew Morton <akpm@linux-foundation.org>
> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> > ---
> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> > arch/arm/mach-at91/board.h | 4 +-
> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> > arch/avr32/boards/favr-32/setup.c | 2 +-
> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> > arch/avr32/boards/merisc/display.c | 2 +-
> > arch/avr32/boards/mimc200/setup.c | 4 +-
> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> > include/video/atmel_lcdc.h | 24 +------
> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >
> [snip]
> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> > index c1a2914..98733cd4 100644
> > --- a/drivers/video/atmel_lcdfb.c
> > +++ b/drivers/video/atmel_lcdfb.c
> > @@ -20,12 +20,45 @@
> > #include <linux/gfp.h>
> > #include <linux/module.h>
> > #include <linux/platform_data/atmel.h>
> > +#include <video/of_display_timing.h>
> >
> > #include <mach/cpu.h>
> > #include <asm/gpio.h>
> >
> > #include <video/atmel_lcdc.h>
> >
> > +struct atmel_lcdfb_config {
> > + bool have_alt_pixclock;
> > + bool have_hozval;
> > + bool have_intensity_bit;
> > +};
> > +
> > + /* LCD Controller info data structure, stored in device platform_data */
> > +struct atmel_lcdfb_info {
> > + spinlock_t lock;
> > + struct fb_info *info;
> > + void __iomem *mmio;
> > + int irq_base;
> > + struct work_struct task;
> > +
> > + unsigned int smem_len;
> > + struct platform_device *pdev;
> > + struct clk *bus_clk;
> > + struct clk *lcdc_clk;
> > +
> > + struct backlight_device *backlight;
> > + u8 bl_power;
> > + bool lcdcon_pol_negative;
> I think lcdcon_pol_negative should be part of pdata, because it really
> depends on how the PWM is wired on the board.
>
maybe but no one mainline use it on any pdata for non-dt boars
so I did not want to expose it
Best Regatgards,
J.
>
> Regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-29 17:35 UTC (permalink / raw)
To: linux-arm-kernel
On 16:36 Wed 29 May , Richard Genoud wrote:
> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: linux-fbdev@vger.kernel.org
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Andrew Morton <akpm@linux-foundation.org>
> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> > ---
> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> > arch/arm/mach-at91/board.h | 4 +-
> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> > arch/avr32/boards/favr-32/setup.c | 2 +-
> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> > arch/avr32/boards/merisc/display.c | 2 +-
> > arch/avr32/boards/mimc200/setup.c | 4 +-
> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> > include/video/atmel_lcdc.h | 24 +------
> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >
> [snip]
> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> > index c1a2914..98733cd4 100644
> > --- a/drivers/video/atmel_lcdfb.c
> > +++ b/drivers/video/atmel_lcdfb.c
> > @@ -20,12 +20,45 @@
> > #include <linux/gfp.h>
> > #include <linux/module.h>
> > #include <linux/platform_data/atmel.h>
> > +#include <video/of_display_timing.h>
> >
> > #include <mach/cpu.h>
> > #include <asm/gpio.h>
> >
> > #include <video/atmel_lcdc.h>
> >
> > +struct atmel_lcdfb_config {
> > + bool have_alt_pixclock;
> > + bool have_hozval;
> > + bool have_intensity_bit;
> > +};
> > +
> > + /* LCD Controller info data structure, stored in device platform_data */
> > +struct atmel_lcdfb_info {
> > + spinlock_t lock;
> > + struct fb_info *info;
> > + void __iomem *mmio;
> > + int irq_base;
> > + struct work_struct task;
> > +
> > + unsigned int smem_len;
> > + struct platform_device *pdev;
> > + struct clk *bus_clk;
> > + struct clk *lcdc_clk;
> > +
> > + struct backlight_device *backlight;
> > + u8 bl_power;
> > + bool lcdcon_pol_negative;
> I think lcdcon_pol_negative should be part of pdata, because it really
> depends on how the PWM is wired on the board.
>
maybe but no one mainline use it on any pdata for non-dt boars
so I did not want to expose it
Best Regatgards,
J.
>
> Regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-29 17:35 UTC (permalink / raw)
To: linux-arm-kernel
On 16:36 Wed 29 May , Richard Genoud wrote:
> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: linux-fbdev at vger.kernel.org
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Andrew Morton <akpm@linux-foundation.org>
> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> > ---
> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> > arch/arm/mach-at91/board.h | 4 +-
> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> > arch/avr32/boards/favr-32/setup.c | 2 +-
> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> > arch/avr32/boards/merisc/display.c | 2 +-
> > arch/avr32/boards/mimc200/setup.c | 4 +-
> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> > include/video/atmel_lcdc.h | 24 +------
> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >
> [snip]
> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> > index c1a2914..98733cd4 100644
> > --- a/drivers/video/atmel_lcdfb.c
> > +++ b/drivers/video/atmel_lcdfb.c
> > @@ -20,12 +20,45 @@
> > #include <linux/gfp.h>
> > #include <linux/module.h>
> > #include <linux/platform_data/atmel.h>
> > +#include <video/of_display_timing.h>
> >
> > #include <mach/cpu.h>
> > #include <asm/gpio.h>
> >
> > #include <video/atmel_lcdc.h>
> >
> > +struct atmel_lcdfb_config {
> > + bool have_alt_pixclock;
> > + bool have_hozval;
> > + bool have_intensity_bit;
> > +};
> > +
> > + /* LCD Controller info data structure, stored in device platform_data */
> > +struct atmel_lcdfb_info {
> > + spinlock_t lock;
> > + struct fb_info *info;
> > + void __iomem *mmio;
> > + int irq_base;
> > + struct work_struct task;
> > +
> > + unsigned int smem_len;
> > + struct platform_device *pdev;
> > + struct clk *bus_clk;
> > + struct clk *lcdc_clk;
> > +
> > + struct backlight_device *backlight;
> > + u8 bl_power;
> > + bool lcdcon_pol_negative;
> I think lcdcon_pol_negative should be part of pdata, because it really
> depends on how the PWM is wired on the board.
>
maybe but no one mainline use it on any pdata for non-dt boars
so I did not want to expose it
Best Regatgards,
J.
>
> Regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-05-29 17:44 ` Richard Genoud
-1 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 17:44 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andreas Bießmann,
Andrew Morton, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Hans-Christian Egtvedt
2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
> On 16:36 Wed 29 May , Richard Genoud wrote:
>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
>> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>> >
>> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
>> > Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> > Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
>> > Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
>> > Cc: Hans-Christian Egtvedt <egtvedt-BrfabpQBY5qlHtIdYg32fQ@public.gmane.org>
>> > ---
>> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>> > arch/arm/mach-at91/board.h | 4 +-
>> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
>> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>> > arch/avr32/boards/atstk1000/setup.c | 2 +-
>> > arch/avr32/boards/favr-32/setup.c | 2 +-
>> > arch/avr32/boards/hammerhead/setup.c | 2 +-
>> > arch/avr32/boards/merisc/display.c | 2 +-
>> > arch/avr32/boards/mimc200/setup.c | 4 +-
>> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>> > include/video/atmel_lcdc.h | 24 +------
>> > 21 files changed, 109 insertions(+), 101 deletions(-)
>> >
>> [snip]
>> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>> > index c1a2914..98733cd4 100644
>> > --- a/drivers/video/atmel_lcdfb.c
>> > +++ b/drivers/video/atmel_lcdfb.c
>> > @@ -20,12 +20,45 @@
>> > #include <linux/gfp.h>
>> > #include <linux/module.h>
>> > #include <linux/platform_data/atmel.h>
>> > +#include <video/of_display_timing.h>
>> >
>> > #include <mach/cpu.h>
>> > #include <asm/gpio.h>
>> >
>> > #include <video/atmel_lcdc.h>
>> >
>> > +struct atmel_lcdfb_config {
>> > + bool have_alt_pixclock;
>> > + bool have_hozval;
>> > + bool have_intensity_bit;
>> > +};
>> > +
>> > + /* LCD Controller info data structure, stored in device platform_data */
>> > +struct atmel_lcdfb_info {
>> > + spinlock_t lock;
>> > + struct fb_info *info;
>> > + void __iomem *mmio;
>> > + int irq_base;
>> > + struct work_struct task;
>> > +
>> > + unsigned int smem_len;
>> > + struct platform_device *pdev;
>> > + struct clk *bus_clk;
>> > + struct clk *lcdc_clk;
>> > +
>> > + struct backlight_device *backlight;
>> > + u8 bl_power;
>> > + bool lcdcon_pol_negative;
>> I think lcdcon_pol_negative should be part of pdata, because it really
>> depends on how the PWM is wired on the board.
>>
>
> maybe but no one mainline use it on any pdata for non-dt boars
> so I did not want to expose it
Well, at least, I'm using it :)
(and I guess that Andreas is using it also, otherwise he wouldn't have
introduce it !)
Best regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 17:44 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 17:44 UTC (permalink / raw)
To: linux-arm-kernel
2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> On 16:36 Wed 29 May , Richard Genoud wrote:
>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>> >
>> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>> > Cc: linux-fbdev@vger.kernel.org
>> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>> > Cc: Andrew Morton <akpm@linux-foundation.org>
>> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>> > ---
>> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>> > arch/arm/mach-at91/board.h | 4 +-
>> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
>> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>> > arch/avr32/boards/atstk1000/setup.c | 2 +-
>> > arch/avr32/boards/favr-32/setup.c | 2 +-
>> > arch/avr32/boards/hammerhead/setup.c | 2 +-
>> > arch/avr32/boards/merisc/display.c | 2 +-
>> > arch/avr32/boards/mimc200/setup.c | 4 +-
>> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>> > include/video/atmel_lcdc.h | 24 +------
>> > 21 files changed, 109 insertions(+), 101 deletions(-)
>> >
>> [snip]
>> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>> > index c1a2914..98733cd4 100644
>> > --- a/drivers/video/atmel_lcdfb.c
>> > +++ b/drivers/video/atmel_lcdfb.c
>> > @@ -20,12 +20,45 @@
>> > #include <linux/gfp.h>
>> > #include <linux/module.h>
>> > #include <linux/platform_data/atmel.h>
>> > +#include <video/of_display_timing.h>
>> >
>> > #include <mach/cpu.h>
>> > #include <asm/gpio.h>
>> >
>> > #include <video/atmel_lcdc.h>
>> >
>> > +struct atmel_lcdfb_config {
>> > + bool have_alt_pixclock;
>> > + bool have_hozval;
>> > + bool have_intensity_bit;
>> > +};
>> > +
>> > + /* LCD Controller info data structure, stored in device platform_data */
>> > +struct atmel_lcdfb_info {
>> > + spinlock_t lock;
>> > + struct fb_info *info;
>> > + void __iomem *mmio;
>> > + int irq_base;
>> > + struct work_struct task;
>> > +
>> > + unsigned int smem_len;
>> > + struct platform_device *pdev;
>> > + struct clk *bus_clk;
>> > + struct clk *lcdc_clk;
>> > +
>> > + struct backlight_device *backlight;
>> > + u8 bl_power;
>> > + bool lcdcon_pol_negative;
>> I think lcdcon_pol_negative should be part of pdata, because it really
>> depends on how the PWM is wired on the board.
>>
>
> maybe but no one mainline use it on any pdata for non-dt boars
> so I did not want to expose it
Well, at least, I'm using it :)
(and I guess that Andreas is using it also, otherwise he wouldn't have
introduce it !)
Best regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 17:44 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-29 17:44 UTC (permalink / raw)
To: linux-arm-kernel
2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> On 16:36 Wed 29 May , Richard Genoud wrote:
>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>> >
>> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>> > Cc: linux-fbdev at vger.kernel.org
>> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>> > Cc: Andrew Morton <akpm@linux-foundation.org>
>> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>> > ---
>> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>> > arch/arm/mach-at91/board.h | 4 +-
>> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
>> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>> > arch/avr32/boards/atstk1000/setup.c | 2 +-
>> > arch/avr32/boards/favr-32/setup.c | 2 +-
>> > arch/avr32/boards/hammerhead/setup.c | 2 +-
>> > arch/avr32/boards/merisc/display.c | 2 +-
>> > arch/avr32/boards/mimc200/setup.c | 4 +-
>> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>> > include/video/atmel_lcdc.h | 24 +------
>> > 21 files changed, 109 insertions(+), 101 deletions(-)
>> >
>> [snip]
>> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>> > index c1a2914..98733cd4 100644
>> > --- a/drivers/video/atmel_lcdfb.c
>> > +++ b/drivers/video/atmel_lcdfb.c
>> > @@ -20,12 +20,45 @@
>> > #include <linux/gfp.h>
>> > #include <linux/module.h>
>> > #include <linux/platform_data/atmel.h>
>> > +#include <video/of_display_timing.h>
>> >
>> > #include <mach/cpu.h>
>> > #include <asm/gpio.h>
>> >
>> > #include <video/atmel_lcdc.h>
>> >
>> > +struct atmel_lcdfb_config {
>> > + bool have_alt_pixclock;
>> > + bool have_hozval;
>> > + bool have_intensity_bit;
>> > +};
>> > +
>> > + /* LCD Controller info data structure, stored in device platform_data */
>> > +struct atmel_lcdfb_info {
>> > + spinlock_t lock;
>> > + struct fb_info *info;
>> > + void __iomem *mmio;
>> > + int irq_base;
>> > + struct work_struct task;
>> > +
>> > + unsigned int smem_len;
>> > + struct platform_device *pdev;
>> > + struct clk *bus_clk;
>> > + struct clk *lcdc_clk;
>> > +
>> > + struct backlight_device *backlight;
>> > + u8 bl_power;
>> > + bool lcdcon_pol_negative;
>> I think lcdcon_pol_negative should be part of pdata, because it really
>> depends on how the PWM is wired on the board.
>>
>
> maybe but no one mainline use it on any pdata for non-dt boars
> so I did not want to expose it
Well, at least, I'm using it :)
(and I guess that Andreas is using it also, otherwise he wouldn't have
introduce it !)
Best regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-29 17:44 ` Richard Genoud
(?)
@ 2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-29 19:32 UTC (permalink / raw)
To: Richard Genoud
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andreas Bießmann,
Andrew Morton, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Hans-Christian Egtvedt
On 19:44 Wed 29 May , Richard Genoud wrote:
> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
> > On 16:36 Wed 29 May , Richard Genoud wrote:
> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >> >
> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
> >> > Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> >> > Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
> >> > Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
> >> > Cc: Hans-Christian Egtvedt <egtvedt-BrfabpQBY5qlHtIdYg32fQ@public.gmane.org>
> >> > ---
> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >> > arch/arm/mach-at91/board.h | 4 +-
> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> >> > arch/avr32/boards/merisc/display.c | 2 +-
> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >> > include/video/atmel_lcdc.h | 24 +------
> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >> >
> >> [snip]
> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >> > index c1a2914..98733cd4 100644
> >> > --- a/drivers/video/atmel_lcdfb.c
> >> > +++ b/drivers/video/atmel_lcdfb.c
> >> > @@ -20,12 +20,45 @@
> >> > #include <linux/gfp.h>
> >> > #include <linux/module.h>
> >> > #include <linux/platform_data/atmel.h>
> >> > +#include <video/of_display_timing.h>
> >> >
> >> > #include <mach/cpu.h>
> >> > #include <asm/gpio.h>
> >> >
> >> > #include <video/atmel_lcdc.h>
> >> >
> >> > +struct atmel_lcdfb_config {
> >> > + bool have_alt_pixclock;
> >> > + bool have_hozval;
> >> > + bool have_intensity_bit;
> >> > +};
> >> > +
> >> > + /* LCD Controller info data structure, stored in device platform_data */
> >> > +struct atmel_lcdfb_info {
> >> > + spinlock_t lock;
> >> > + struct fb_info *info;
> >> > + void __iomem *mmio;
> >> > + int irq_base;
> >> > + struct work_struct task;
> >> > +
> >> > + unsigned int smem_len;
> >> > + struct platform_device *pdev;
> >> > + struct clk *bus_clk;
> >> > + struct clk *lcdc_clk;
> >> > +
> >> > + struct backlight_device *backlight;
> >> > + u8 bl_power;
> >> > + bool lcdcon_pol_negative;
> >> I think lcdcon_pol_negative should be part of pdata, because it really
> >> depends on how the PWM is wired on the board.
> >>
> >
> > maybe but no one mainline use it on any pdata for non-dt boars
> > so I did not want to expose it
> Well, at least, I'm using it :)
> (and I guess that Andreas is using it also, otherwise he wouldn't have
> introduce it !)
yes but pdata is for non-dt boards, for dt you can keep it in struct
atmel_lcdfb_info and add a property
if non-dt boards want it my answer is I do not care switch to DT
Best Regards,
J.
>
>
> Best regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-29 19:32 UTC (permalink / raw)
To: linux-arm-kernel
On 19:44 Wed 29 May , Richard Genoud wrote:
> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > On 16:36 Wed 29 May , Richard Genoud wrote:
> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >> >
> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >> > Cc: linux-fbdev@vger.kernel.org
> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >> > ---
> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >> > arch/arm/mach-at91/board.h | 4 +-
> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> >> > arch/avr32/boards/merisc/display.c | 2 +-
> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >> > include/video/atmel_lcdc.h | 24 +------
> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >> >
> >> [snip]
> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >> > index c1a2914..98733cd4 100644
> >> > --- a/drivers/video/atmel_lcdfb.c
> >> > +++ b/drivers/video/atmel_lcdfb.c
> >> > @@ -20,12 +20,45 @@
> >> > #include <linux/gfp.h>
> >> > #include <linux/module.h>
> >> > #include <linux/platform_data/atmel.h>
> >> > +#include <video/of_display_timing.h>
> >> >
> >> > #include <mach/cpu.h>
> >> > #include <asm/gpio.h>
> >> >
> >> > #include <video/atmel_lcdc.h>
> >> >
> >> > +struct atmel_lcdfb_config {
> >> > + bool have_alt_pixclock;
> >> > + bool have_hozval;
> >> > + bool have_intensity_bit;
> >> > +};
> >> > +
> >> > + /* LCD Controller info data structure, stored in device platform_data */
> >> > +struct atmel_lcdfb_info {
> >> > + spinlock_t lock;
> >> > + struct fb_info *info;
> >> > + void __iomem *mmio;
> >> > + int irq_base;
> >> > + struct work_struct task;
> >> > +
> >> > + unsigned int smem_len;
> >> > + struct platform_device *pdev;
> >> > + struct clk *bus_clk;
> >> > + struct clk *lcdc_clk;
> >> > +
> >> > + struct backlight_device *backlight;
> >> > + u8 bl_power;
> >> > + bool lcdcon_pol_negative;
> >> I think lcdcon_pol_negative should be part of pdata, because it really
> >> depends on how the PWM is wired on the board.
> >>
> >
> > maybe but no one mainline use it on any pdata for non-dt boars
> > so I did not want to expose it
> Well, at least, I'm using it :)
> (and I guess that Andreas is using it also, otherwise he wouldn't have
> introduce it !)
yes but pdata is for non-dt boards, for dt you can keep it in struct
atmel_lcdfb_info and add a property
if non-dt boards want it my answer is I do not care switch to DT
Best Regards,
J.
>
>
> Best regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-29 19:32 UTC (permalink / raw)
To: linux-arm-kernel
On 19:44 Wed 29 May , Richard Genoud wrote:
> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > On 16:36 Wed 29 May , Richard Genoud wrote:
> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >> >
> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >> > Cc: linux-fbdev at vger.kernel.org
> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >> > ---
> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >> > arch/arm/mach-at91/board.h | 4 +-
> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> >> > arch/avr32/boards/merisc/display.c | 2 +-
> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >> > include/video/atmel_lcdc.h | 24 +------
> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >> >
> >> [snip]
> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >> > index c1a2914..98733cd4 100644
> >> > --- a/drivers/video/atmel_lcdfb.c
> >> > +++ b/drivers/video/atmel_lcdfb.c
> >> > @@ -20,12 +20,45 @@
> >> > #include <linux/gfp.h>
> >> > #include <linux/module.h>
> >> > #include <linux/platform_data/atmel.h>
> >> > +#include <video/of_display_timing.h>
> >> >
> >> > #include <mach/cpu.h>
> >> > #include <asm/gpio.h>
> >> >
> >> > #include <video/atmel_lcdc.h>
> >> >
> >> > +struct atmel_lcdfb_config {
> >> > + bool have_alt_pixclock;
> >> > + bool have_hozval;
> >> > + bool have_intensity_bit;
> >> > +};
> >> > +
> >> > + /* LCD Controller info data structure, stored in device platform_data */
> >> > +struct atmel_lcdfb_info {
> >> > + spinlock_t lock;
> >> > + struct fb_info *info;
> >> > + void __iomem *mmio;
> >> > + int irq_base;
> >> > + struct work_struct task;
> >> > +
> >> > + unsigned int smem_len;
> >> > + struct platform_device *pdev;
> >> > + struct clk *bus_clk;
> >> > + struct clk *lcdc_clk;
> >> > +
> >> > + struct backlight_device *backlight;
> >> > + u8 bl_power;
> >> > + bool lcdcon_pol_negative;
> >> I think lcdcon_pol_negative should be part of pdata, because it really
> >> depends on how the PWM is wired on the board.
> >>
> >
> > maybe but no one mainline use it on any pdata for non-dt boars
> > so I did not want to expose it
> Well, at least, I'm using it :)
> (and I guess that Andreas is using it also, otherwise he wouldn't have
> introduce it !)
yes but pdata is for non-dt boards, for dt you can keep it in struct
atmel_lcdfb_info and add a property
if non-dt boards want it my answer is I do not care switch to DT
Best Regards,
J.
>
>
> Best regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-05-30 6:39 ` Richard Genoud
-1 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-30 6:39 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA,
devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Andreas Bießmann,
Andrew Morton, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Hans-Christian Egtvedt
2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
> On 19:44 Wed 29 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
>> > On 16:36 Wed 29 May , Richard Genoud wrote:
>> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>:
>> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>> >> >
>> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
>> >> > Cc: linux-fbdev-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
>> >> > Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
>> >> > Cc: Andrew Morton <akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org>
>> >> > Cc: Hans-Christian Egtvedt <egtvedt-BrfabpQBY5qlHtIdYg32fQ@public.gmane.org>
>> >> > ---
>> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>> >> > arch/arm/mach-at91/board.h | 4 +-
>> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
>> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
>> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
>> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
>> >> > arch/avr32/boards/merisc/display.c | 2 +-
>> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
>> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>> >> > include/video/atmel_lcdc.h | 24 +------
>> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
>> >> >
>> >> [snip]
>> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>> >> > index c1a2914..98733cd4 100644
>> >> > --- a/drivers/video/atmel_lcdfb.c
>> >> > +++ b/drivers/video/atmel_lcdfb.c
>> >> > @@ -20,12 +20,45 @@
>> >> > #include <linux/gfp.h>
>> >> > #include <linux/module.h>
>> >> > #include <linux/platform_data/atmel.h>
>> >> > +#include <video/of_display_timing.h>
>> >> >
>> >> > #include <mach/cpu.h>
>> >> > #include <asm/gpio.h>
>> >> >
>> >> > #include <video/atmel_lcdc.h>
>> >> >
>> >> > +struct atmel_lcdfb_config {
>> >> > + bool have_alt_pixclock;
>> >> > + bool have_hozval;
>> >> > + bool have_intensity_bit;
>> >> > +};
>> >> > +
>> >> > + /* LCD Controller info data structure, stored in device platform_data */
>> >> > +struct atmel_lcdfb_info {
>> >> > + spinlock_t lock;
>> >> > + struct fb_info *info;
>> >> > + void __iomem *mmio;
>> >> > + int irq_base;
>> >> > + struct work_struct task;
>> >> > +
>> >> > + unsigned int smem_len;
>> >> > + struct platform_device *pdev;
>> >> > + struct clk *bus_clk;
>> >> > + struct clk *lcdc_clk;
>> >> > +
>> >> > + struct backlight_device *backlight;
>> >> > + u8 bl_power;
>> >> > + bool lcdcon_pol_negative;
>> >> I think lcdcon_pol_negative should be part of pdata, because it really
>> >> depends on how the PWM is wired on the board.
>> >>
>> >
>> > maybe but no one mainline use it on any pdata for non-dt boars
>> > so I did not want to expose it
>> Well, at least, I'm using it :)
>> (and I guess that Andreas is using it also, otherwise he wouldn't have
>> introduce it !)
>
> yes but pdata is for non-dt boards, for dt you can keep it in struct
> atmel_lcdfb_info and add a property
>
> if non-dt boards want it my answer is I do not care switch to DT
ok (I use a full DT board based on sam9g35)
so I'll add something like
sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
"atmel,lcdcon-pwm-pulse-low");
in /atmel_lcdfb.c
But I thought the goal of this patch was to separate driver data from
platform specific data, and IMHO, lcdcon_pol_negative is a specificity
of the platform.
Best regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 6:39 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-30 6:39 UTC (permalink / raw)
To: linux-arm-kernel
2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> On 19:44 Wed 29 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > On 16:36 Wed 29 May , Richard Genoud wrote:
>> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>> >> >
>> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>> >> > Cc: linux-fbdev@vger.kernel.org
>> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
>> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>> >> > ---
>> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>> >> > arch/arm/mach-at91/board.h | 4 +-
>> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
>> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
>> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
>> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
>> >> > arch/avr32/boards/merisc/display.c | 2 +-
>> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
>> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>> >> > include/video/atmel_lcdc.h | 24 +------
>> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
>> >> >
>> >> [snip]
>> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>> >> > index c1a2914..98733cd4 100644
>> >> > --- a/drivers/video/atmel_lcdfb.c
>> >> > +++ b/drivers/video/atmel_lcdfb.c
>> >> > @@ -20,12 +20,45 @@
>> >> > #include <linux/gfp.h>
>> >> > #include <linux/module.h>
>> >> > #include <linux/platform_data/atmel.h>
>> >> > +#include <video/of_display_timing.h>
>> >> >
>> >> > #include <mach/cpu.h>
>> >> > #include <asm/gpio.h>
>> >> >
>> >> > #include <video/atmel_lcdc.h>
>> >> >
>> >> > +struct atmel_lcdfb_config {
>> >> > + bool have_alt_pixclock;
>> >> > + bool have_hozval;
>> >> > + bool have_intensity_bit;
>> >> > +};
>> >> > +
>> >> > + /* LCD Controller info data structure, stored in device platform_data */
>> >> > +struct atmel_lcdfb_info {
>> >> > + spinlock_t lock;
>> >> > + struct fb_info *info;
>> >> > + void __iomem *mmio;
>> >> > + int irq_base;
>> >> > + struct work_struct task;
>> >> > +
>> >> > + unsigned int smem_len;
>> >> > + struct platform_device *pdev;
>> >> > + struct clk *bus_clk;
>> >> > + struct clk *lcdc_clk;
>> >> > +
>> >> > + struct backlight_device *backlight;
>> >> > + u8 bl_power;
>> >> > + bool lcdcon_pol_negative;
>> >> I think lcdcon_pol_negative should be part of pdata, because it really
>> >> depends on how the PWM is wired on the board.
>> >>
>> >
>> > maybe but no one mainline use it on any pdata for non-dt boars
>> > so I did not want to expose it
>> Well, at least, I'm using it :)
>> (and I guess that Andreas is using it also, otherwise he wouldn't have
>> introduce it !)
>
> yes but pdata is for non-dt boards, for dt you can keep it in struct
> atmel_lcdfb_info and add a property
>
> if non-dt boards want it my answer is I do not care switch to DT
ok (I use a full DT board based on sam9g35)
so I'll add something like
sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
"atmel,lcdcon-pwm-pulse-low");
in /atmel_lcdfb.c
But I thought the goal of this patch was to separate driver data from
platform specific data, and IMHO, lcdcon_pol_negative is a specificity
of the platform.
Best regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 6:39 ` Richard Genoud
0 siblings, 0 replies; 91+ messages in thread
From: Richard Genoud @ 2013-05-30 6:39 UTC (permalink / raw)
To: linux-arm-kernel
2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> On 19:44 Wed 29 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > On 16:36 Wed 29 May , Richard Genoud wrote:
>> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>> >> >
>> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>> >> > Cc: linux-fbdev at vger.kernel.org
>> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
>> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>> >> > ---
>> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>> >> > arch/arm/mach-at91/board.h | 4 +-
>> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
>> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
>> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
>> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
>> >> > arch/avr32/boards/merisc/display.c | 2 +-
>> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
>> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>> >> > include/video/atmel_lcdc.h | 24 +------
>> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
>> >> >
>> >> [snip]
>> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>> >> > index c1a2914..98733cd4 100644
>> >> > --- a/drivers/video/atmel_lcdfb.c
>> >> > +++ b/drivers/video/atmel_lcdfb.c
>> >> > @@ -20,12 +20,45 @@
>> >> > #include <linux/gfp.h>
>> >> > #include <linux/module.h>
>> >> > #include <linux/platform_data/atmel.h>
>> >> > +#include <video/of_display_timing.h>
>> >> >
>> >> > #include <mach/cpu.h>
>> >> > #include <asm/gpio.h>
>> >> >
>> >> > #include <video/atmel_lcdc.h>
>> >> >
>> >> > +struct atmel_lcdfb_config {
>> >> > + bool have_alt_pixclock;
>> >> > + bool have_hozval;
>> >> > + bool have_intensity_bit;
>> >> > +};
>> >> > +
>> >> > + /* LCD Controller info data structure, stored in device platform_data */
>> >> > +struct atmel_lcdfb_info {
>> >> > + spinlock_t lock;
>> >> > + struct fb_info *info;
>> >> > + void __iomem *mmio;
>> >> > + int irq_base;
>> >> > + struct work_struct task;
>> >> > +
>> >> > + unsigned int smem_len;
>> >> > + struct platform_device *pdev;
>> >> > + struct clk *bus_clk;
>> >> > + struct clk *lcdc_clk;
>> >> > +
>> >> > + struct backlight_device *backlight;
>> >> > + u8 bl_power;
>> >> > + bool lcdcon_pol_negative;
>> >> I think lcdcon_pol_negative should be part of pdata, because it really
>> >> depends on how the PWM is wired on the board.
>> >>
>> >
>> > maybe but no one mainline use it on any pdata for non-dt boars
>> > so I did not want to expose it
>> Well, at least, I'm using it :)
>> (and I guess that Andreas is using it also, otherwise he wouldn't have
>> introduce it !)
>
> yes but pdata is for non-dt boards, for dt you can keep it in struct
> atmel_lcdfb_info and add a property
>
> if non-dt boards want it my answer is I do not care switch to DT
ok (I use a full DT board based on sam9g35)
so I'll add something like
sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
"atmel,lcdcon-pwm-pulse-low");
in /atmel_lcdfb.c
But I thought the goal of this patch was to separate driver data from
platform specific data, and IMHO, lcdcon_pol_negative is a specificity
of the platform.
Best regards,
Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-30 6:39 ` Richard Genoud
(?)
@ 2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-30 7:23 UTC (permalink / raw)
To: Richard Genoud
Cc: linux-fbdev, devicetree-discuss, Nicolas Ferre,
Andreas Bießmann, Andrew Morton, linux-arm-kernel,
Hans-Christian Egtvedt
On 08:39 Thu 30 May , Richard Genoud wrote:
> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > On 19:44 Wed 29 May , Richard Genoud wrote:
> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> > On 16:36 Wed 29 May , Richard Genoud wrote:
> >> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >> >> >
> >> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >> >> > Cc: linux-fbdev@vger.kernel.org
> >> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
> >> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >> >> > ---
> >> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >> >> > arch/arm/mach-at91/board.h | 4 +-
> >> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> >> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
> >> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> >> >> > arch/avr32/boards/merisc/display.c | 2 +-
> >> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
> >> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >> >> > include/video/atmel_lcdc.h | 24 +------
> >> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >> >> >
> >> >> [snip]
> >> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >> >> > index c1a2914..98733cd4 100644
> >> >> > --- a/drivers/video/atmel_lcdfb.c
> >> >> > +++ b/drivers/video/atmel_lcdfb.c
> >> >> > @@ -20,12 +20,45 @@
> >> >> > #include <linux/gfp.h>
> >> >> > #include <linux/module.h>
> >> >> > #include <linux/platform_data/atmel.h>
> >> >> > +#include <video/of_display_timing.h>
> >> >> >
> >> >> > #include <mach/cpu.h>
> >> >> > #include <asm/gpio.h>
> >> >> >
> >> >> > #include <video/atmel_lcdc.h>
> >> >> >
> >> >> > +struct atmel_lcdfb_config {
> >> >> > + bool have_alt_pixclock;
> >> >> > + bool have_hozval;
> >> >> > + bool have_intensity_bit;
> >> >> > +};
> >> >> > +
> >> >> > + /* LCD Controller info data structure, stored in device platform_data */
> >> >> > +struct atmel_lcdfb_info {
> >> >> > + spinlock_t lock;
> >> >> > + struct fb_info *info;
> >> >> > + void __iomem *mmio;
> >> >> > + int irq_base;
> >> >> > + struct work_struct task;
> >> >> > +
> >> >> > + unsigned int smem_len;
> >> >> > + struct platform_device *pdev;
> >> >> > + struct clk *bus_clk;
> >> >> > + struct clk *lcdc_clk;
> >> >> > +
> >> >> > + struct backlight_device *backlight;
> >> >> > + u8 bl_power;
> >> >> > + bool lcdcon_pol_negative;
> >> >> I think lcdcon_pol_negative should be part of pdata, because it really
> >> >> depends on how the PWM is wired on the board.
> >> >>
> >> >
> >> > maybe but no one mainline use it on any pdata for non-dt boars
> >> > so I did not want to expose it
> >> Well, at least, I'm using it :)
> >> (and I guess that Andreas is using it also, otherwise he wouldn't have
> >> introduce it !)
> >
> > yes but pdata is for non-dt boards, for dt you can keep it in struct
> > atmel_lcdfb_info and add a property
> >
> > if non-dt boards want it my answer is I do not care switch to DT
>
> ok (I use a full DT board based on sam9g35)
>
> so I'll add something like
> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
> "atmel,lcdcon-pwm-pulse-low");
> in /atmel_lcdfb.c
>
> But I thought the goal of this patch was to separate driver data from
> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
> of the platform.
You are right but as non one mainline use it as pdata I choose to drop it
and only keep it on the driver as we can still use it for DT
It's a way to force peopoe to switch to DT
Best Regards,
J.
>
> Best regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-30 7:23 UTC (permalink / raw)
To: linux-arm-kernel
On 08:39 Thu 30 May , Richard Genoud wrote:
> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > On 19:44 Wed 29 May , Richard Genoud wrote:
> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> > On 16:36 Wed 29 May , Richard Genoud wrote:
> >> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >> >> >
> >> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >> >> > Cc: linux-fbdev@vger.kernel.org
> >> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
> >> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >> >> > ---
> >> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >> >> > arch/arm/mach-at91/board.h | 4 +-
> >> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> >> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
> >> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> >> >> > arch/avr32/boards/merisc/display.c | 2 +-
> >> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
> >> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >> >> > include/video/atmel_lcdc.h | 24 +------
> >> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >> >> >
> >> >> [snip]
> >> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >> >> > index c1a2914..98733cd4 100644
> >> >> > --- a/drivers/video/atmel_lcdfb.c
> >> >> > +++ b/drivers/video/atmel_lcdfb.c
> >> >> > @@ -20,12 +20,45 @@
> >> >> > #include <linux/gfp.h>
> >> >> > #include <linux/module.h>
> >> >> > #include <linux/platform_data/atmel.h>
> >> >> > +#include <video/of_display_timing.h>
> >> >> >
> >> >> > #include <mach/cpu.h>
> >> >> > #include <asm/gpio.h>
> >> >> >
> >> >> > #include <video/atmel_lcdc.h>
> >> >> >
> >> >> > +struct atmel_lcdfb_config {
> >> >> > + bool have_alt_pixclock;
> >> >> > + bool have_hozval;
> >> >> > + bool have_intensity_bit;
> >> >> > +};
> >> >> > +
> >> >> > + /* LCD Controller info data structure, stored in device platform_data */
> >> >> > +struct atmel_lcdfb_info {
> >> >> > + spinlock_t lock;
> >> >> > + struct fb_info *info;
> >> >> > + void __iomem *mmio;
> >> >> > + int irq_base;
> >> >> > + struct work_struct task;
> >> >> > +
> >> >> > + unsigned int smem_len;
> >> >> > + struct platform_device *pdev;
> >> >> > + struct clk *bus_clk;
> >> >> > + struct clk *lcdc_clk;
> >> >> > +
> >> >> > + struct backlight_device *backlight;
> >> >> > + u8 bl_power;
> >> >> > + bool lcdcon_pol_negative;
> >> >> I think lcdcon_pol_negative should be part of pdata, because it really
> >> >> depends on how the PWM is wired on the board.
> >> >>
> >> >
> >> > maybe but no one mainline use it on any pdata for non-dt boars
> >> > so I did not want to expose it
> >> Well, at least, I'm using it :)
> >> (and I guess that Andreas is using it also, otherwise he wouldn't have
> >> introduce it !)
> >
> > yes but pdata is for non-dt boards, for dt you can keep it in struct
> > atmel_lcdfb_info and add a property
> >
> > if non-dt boards want it my answer is I do not care switch to DT
>
> ok (I use a full DT board based on sam9g35)
>
> so I'll add something like
> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
> "atmel,lcdcon-pwm-pulse-low");
> in /atmel_lcdfb.c
>
> But I thought the goal of this patch was to separate driver data from
> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
> of the platform.
You are right but as non one mainline use it as pdata I choose to drop it
and only keep it on the driver as we can still use it for DT
It's a way to force peopoe to switch to DT
Best Regards,
J.
>
> Best regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-30 7:23 UTC (permalink / raw)
To: linux-arm-kernel
On 08:39 Thu 30 May , Richard Genoud wrote:
> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> > On 19:44 Wed 29 May , Richard Genoud wrote:
> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> > On 16:36 Wed 29 May , Richard Genoud wrote:
> >> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >> >> > Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >> >> > Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >> >> >
> >> >> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >> >> > Cc: linux-fbdev at vger.kernel.org
> >> >> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >> >> > Cc: Andrew Morton <akpm@linux-foundation.org>
> >> >> > Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >> >> > ---
> >> >> > arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >> >> > arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >> >> > arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >> >> > arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >> >> > arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >> >> > arch/arm/mach-at91/board.h | 4 +-
> >> >> > arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >> >> > arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >> >> > arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >> >> > arch/avr32/boards/atstk1000/setup.c | 2 +-
> >> >> > arch/avr32/boards/favr-32/setup.c | 2 +-
> >> >> > arch/avr32/boards/hammerhead/setup.c | 2 +-
> >> >> > arch/avr32/boards/merisc/display.c | 2 +-
> >> >> > arch/avr32/boards/mimc200/setup.c | 4 +-
> >> >> > arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >> >> > arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >> >> > drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >> >> > include/video/atmel_lcdc.h | 24 +------
> >> >> > 21 files changed, 109 insertions(+), 101 deletions(-)
> >> >> >
> >> >> [snip]
> >> >> > diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >> >> > index c1a2914..98733cd4 100644
> >> >> > --- a/drivers/video/atmel_lcdfb.c
> >> >> > +++ b/drivers/video/atmel_lcdfb.c
> >> >> > @@ -20,12 +20,45 @@
> >> >> > #include <linux/gfp.h>
> >> >> > #include <linux/module.h>
> >> >> > #include <linux/platform_data/atmel.h>
> >> >> > +#include <video/of_display_timing.h>
> >> >> >
> >> >> > #include <mach/cpu.h>
> >> >> > #include <asm/gpio.h>
> >> >> >
> >> >> > #include <video/atmel_lcdc.h>
> >> >> >
> >> >> > +struct atmel_lcdfb_config {
> >> >> > + bool have_alt_pixclock;
> >> >> > + bool have_hozval;
> >> >> > + bool have_intensity_bit;
> >> >> > +};
> >> >> > +
> >> >> > + /* LCD Controller info data structure, stored in device platform_data */
> >> >> > +struct atmel_lcdfb_info {
> >> >> > + spinlock_t lock;
> >> >> > + struct fb_info *info;
> >> >> > + void __iomem *mmio;
> >> >> > + int irq_base;
> >> >> > + struct work_struct task;
> >> >> > +
> >> >> > + unsigned int smem_len;
> >> >> > + struct platform_device *pdev;
> >> >> > + struct clk *bus_clk;
> >> >> > + struct clk *lcdc_clk;
> >> >> > +
> >> >> > + struct backlight_device *backlight;
> >> >> > + u8 bl_power;
> >> >> > + bool lcdcon_pol_negative;
> >> >> I think lcdcon_pol_negative should be part of pdata, because it really
> >> >> depends on how the PWM is wired on the board.
> >> >>
> >> >
> >> > maybe but no one mainline use it on any pdata for non-dt boars
> >> > so I did not want to expose it
> >> Well, at least, I'm using it :)
> >> (and I guess that Andreas is using it also, otherwise he wouldn't have
> >> introduce it !)
> >
> > yes but pdata is for non-dt boards, for dt you can keep it in struct
> > atmel_lcdfb_info and add a property
> >
> > if non-dt boards want it my answer is I do not care switch to DT
>
> ok (I use a full DT board based on sam9g35)
>
> so I'll add something like
> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
> "atmel,lcdcon-pwm-pulse-low");
> in /atmel_lcdfb.c
>
> But I thought the goal of this patch was to separate driver data from
> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
> of the platform.
You are right but as non one mainline use it as pdata I choose to drop it
and only keep it on the driver as we can still use it for DT
It's a way to force peopoe to switch to DT
Best Regards,
J.
>
> Best regards,
> Richard.
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-05-30 14:05 ` Hans-Christian Egtvedt
-1 siblings, 0 replies; 91+ messages in thread
From: Hans-Christian Egtvedt @ 2013-05-30 14:05 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: linux-fbdev, Richard Genoud, devicetree-discuss, Nicolas Ferre,
Andreas Bießmann, Andrew Morton, linux-arm-kernel
Around Thu 30 May 2013 09:23:28 +0200 or thereabout, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 08:39 Thu 30 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > On 19:44 Wed 29 May , Richard Genoud wrote:
>> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> >> > On 16:36 Wed 29 May , Richard Genoud wrote:
>> >> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
<snipp diff>
>> >> >> > + bool lcdcon_pol_negative;
>> >> >> I think lcdcon_pol_negative should be part of pdata, because it really
>> >> >> depends on how the PWM is wired on the board.
>> >> >>
>> >> >
>> >> > maybe but no one mainline use it on any pdata for non-dt boars
>> >> > so I did not want to expose it
>> >> Well, at least, I'm using it :)
>> >> (and I guess that Andreas is using it also, otherwise he wouldn't have
>> >> introduce it !)
>> >
>> > yes but pdata is for non-dt boards, for dt you can keep it in struct
>> > atmel_lcdfb_info and add a property
>> >
>> > if non-dt boards want it my answer is I do not care switch to DT
>>
>> ok (I use a full DT board based on sam9g35)
>>
>> so I'll add something like
>> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
>> "atmel,lcdcon-pwm-pulse-low");
>> in /atmel_lcdfb.c
>>
>> But I thought the goal of this patch was to separate driver data from
>> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
>> of the platform.
>
> You are right but as non one mainline use it as pdata I choose to drop it
> and only keep it on the driver as we can still use it for DT
>
> It's a way to force peopoe to switch to DT
FYI AVR32 architecture doesn't support device tree, nor is it likely to do
so. However there are no users of the PWM output from the LCDC block for the
boards in the current kernel, and I doubt new boards will pop.
--
Hans-Christian Egtvedt
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 14:05 ` Hans-Christian Egtvedt
0 siblings, 0 replies; 91+ messages in thread
From: Hans-Christian Egtvedt @ 2013-05-30 14:05 UTC (permalink / raw)
To: linux-arm-kernel
Around Thu 30 May 2013 09:23:28 +0200 or thereabout, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 08:39 Thu 30 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > On 19:44 Wed 29 May , Richard Genoud wrote:
>> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> >> > On 16:36 Wed 29 May , Richard Genoud wrote:
>> >> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
<snipp diff>
>> >> >> > + bool lcdcon_pol_negative;
>> >> >> I think lcdcon_pol_negative should be part of pdata, because it really
>> >> >> depends on how the PWM is wired on the board.
>> >> >>
>> >> >
>> >> > maybe but no one mainline use it on any pdata for non-dt boars
>> >> > so I did not want to expose it
>> >> Well, at least, I'm using it :)
>> >> (and I guess that Andreas is using it also, otherwise he wouldn't have
>> >> introduce it !)
>> >
>> > yes but pdata is for non-dt boards, for dt you can keep it in struct
>> > atmel_lcdfb_info and add a property
>> >
>> > if non-dt boards want it my answer is I do not care switch to DT
>>
>> ok (I use a full DT board based on sam9g35)
>>
>> so I'll add something like
>> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
>> "atmel,lcdcon-pwm-pulse-low");
>> in /atmel_lcdfb.c
>>
>> But I thought the goal of this patch was to separate driver data from
>> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
>> of the platform.
>
> You are right but as non one mainline use it as pdata I choose to drop it
> and only keep it on the driver as we can still use it for DT
>
> It's a way to force peopoe to switch to DT
FYI AVR32 architecture doesn't support device tree, nor is it likely to do
so. However there are no users of the PWM output from the LCDC block for the
boards in the current kernel, and I doubt new boards will pop.
--
Hans-Christian Egtvedt
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 14:05 ` Hans-Christian Egtvedt
0 siblings, 0 replies; 91+ messages in thread
From: Hans-Christian Egtvedt @ 2013-05-30 14:05 UTC (permalink / raw)
To: linux-arm-kernel
Around Thu 30 May 2013 09:23:28 +0200 or thereabout, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 08:39 Thu 30 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> > On 19:44 Wed 29 May , Richard Genoud wrote:
>> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>> >> > On 16:36 Wed 29 May , Richard Genoud wrote:
>> >> >> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
<snipp diff>
>> >> >> > + bool lcdcon_pol_negative;
>> >> >> I think lcdcon_pol_negative should be part of pdata, because it really
>> >> >> depends on how the PWM is wired on the board.
>> >> >>
>> >> >
>> >> > maybe but no one mainline use it on any pdata for non-dt boars
>> >> > so I did not want to expose it
>> >> Well, at least, I'm using it :)
>> >> (and I guess that Andreas is using it also, otherwise he wouldn't have
>> >> introduce it !)
>> >
>> > yes but pdata is for non-dt boards, for dt you can keep it in struct
>> > atmel_lcdfb_info and add a property
>> >
>> > if non-dt boards want it my answer is I do not care switch to DT
>>
>> ok (I use a full DT board based on sam9g35)
>>
>> so I'll add something like
>> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
>> "atmel,lcdcon-pwm-pulse-low");
>> in /atmel_lcdfb.c
>>
>> But I thought the goal of this patch was to separate driver data from
>> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
>> of the platform.
>
> You are right but as non one mainline use it as pdata I choose to drop it
> and only keep it on the driver as we can still use it for DT
>
> It's a way to force peopoe to switch to DT
FYI AVR32 architecture doesn't support device tree, nor is it likely to do
so. However there are no users of the PWM output from the LCDC block for the
boards in the current kernel, and I doubt new boards will pop.
--
Hans-Christian Egtvedt
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
(?)
@ 2013-05-30 14:27 ` Andreas Bießmann
-1 siblings, 0 replies; 91+ messages in thread
From: Andreas Bießmann @ 2013-05-30 14:27 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD
Cc: linux-fbdev, Richard Genoud, devicetree-discuss, Nicolas Ferre,
Andreas Bießmann, Andrew Morton, linux-arm-kernel,
Hans-Christian Egtvedt
On 30.05.13 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 08:39 Thu 30 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>> On 19:44 Wed 29 May , Richard Genoud wrote:
>>>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>>>> On 16:36 Wed 29 May , Richard Genoud wrote:
>>>>>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>>>>>> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>>>>>>> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>>>>>>>
>>>>>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>>>>>> Cc: linux-fbdev@vger.kernel.org
>>>>>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>>>>>> Cc: Andrew Morton <akpm@linux-foundation.org>
>>>>>>> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>>>>>>> ---
>>>>>>> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>>>>>>> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board.h | 4 +-
>>>>>>> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>>>>>>> arch/avr32/boards/atngw100/mrmt.c | 4 +-
>>>>>>> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>>>>>>> arch/avr32/boards/atstk1000/setup.c | 2 +-
>>>>>>> arch/avr32/boards/favr-32/setup.c | 2 +-
>>>>>>> arch/avr32/boards/hammerhead/setup.c | 2 +-
>>>>>>> arch/avr32/boards/merisc/display.c | 2 +-
>>>>>>> arch/avr32/boards/mimc200/setup.c | 4 +-
>>>>>>> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>>>>>>> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>>>>>>> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>>>>>>> include/video/atmel_lcdc.h | 24 +------
>>>>>>> 21 files changed, 109 insertions(+), 101 deletions(-)
>>>>>>>
>>>>>> [snip]
>>>>>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>>>>>>> index c1a2914..98733cd4 100644
>>>>>>> --- a/drivers/video/atmel_lcdfb.c
>>>>>>> +++ b/drivers/video/atmel_lcdfb.c
>>>>>>> @@ -20,12 +20,45 @@
>>>>>>> #include <linux/gfp.h>
>>>>>>> #include <linux/module.h>
>>>>>>> #include <linux/platform_data/atmel.h>
>>>>>>> +#include <video/of_display_timing.h>
>>>>>>>
>>>>>>> #include <mach/cpu.h>
>>>>>>> #include <asm/gpio.h>
>>>>>>>
>>>>>>> #include <video/atmel_lcdc.h>
>>>>>>>
>>>>>>> +struct atmel_lcdfb_config {
>>>>>>> + bool have_alt_pixclock;
>>>>>>> + bool have_hozval;
>>>>>>> + bool have_intensity_bit;
>>>>>>> +};
>>>>>>> +
>>>>>>> + /* LCD Controller info data structure, stored in device platform_data */
>>>>>>> +struct atmel_lcdfb_info {
>>>>>>> + spinlock_t lock;
>>>>>>> + struct fb_info *info;
>>>>>>> + void __iomem *mmio;
>>>>>>> + int irq_base;
>>>>>>> + struct work_struct task;
>>>>>>> +
>>>>>>> + unsigned int smem_len;
>>>>>>> + struct platform_device *pdev;
>>>>>>> + struct clk *bus_clk;
>>>>>>> + struct clk *lcdc_clk;
>>>>>>> +
>>>>>>> + struct backlight_device *backlight;
>>>>>>> + u8 bl_power;
>>>>>>> + bool lcdcon_pol_negative;
>>>>>> I think lcdcon_pol_negative should be part of pdata, because it really
>>>>>> depends on how the PWM is wired on the board.
>>>>>>
>>>>>
>>>>> maybe but no one mainline use it on any pdata for non-dt boars
>>>>> so I did not want to expose it
>>>> Well, at least, I'm using it :)
>>>> (and I guess that Andreas is using it also, otherwise he wouldn't have
>>>> introduce it !)
>>>
>>> yes but pdata is for non-dt boards, for dt you can keep it in struct
>>> atmel_lcdfb_info and add a property
>>>
>>> if non-dt boards want it my answer is I do not care switch to DT
>>
>> ok (I use a full DT board based on sam9g35)
>>
>> so I'll add something like
>> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
>> "atmel,lcdcon-pwm-pulse-low");
>> in /atmel_lcdfb.c
>>
>> But I thought the goal of this patch was to separate driver data from
>> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
>> of the platform.
>
> You are right but as non one mainline use it as pdata I choose to drop it
> and only keep it on the driver as we can still use it for DT
>
> It's a way to force peopoe to switch to DT
well, we use it on an avr32 board (not mainlined; though no kernel
update planned currently) ... but no way to use DT currently.
Best regards
Andreas Bießmann
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 14:27 ` Andreas Bießmann
0 siblings, 0 replies; 91+ messages in thread
From: Andreas Bießmann @ 2013-05-30 14:27 UTC (permalink / raw)
To: linux-arm-kernel
On 30.05.13 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 08:39 Thu 30 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>> On 19:44 Wed 29 May , Richard Genoud wrote:
>>>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>>>> On 16:36 Wed 29 May , Richard Genoud wrote:
>>>>>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>>>>>> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>>>>>>> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>>>>>>>
>>>>>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>>>>>> Cc: linux-fbdev@vger.kernel.org
>>>>>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>>>>>> Cc: Andrew Morton <akpm@linux-foundation.org>
>>>>>>> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>>>>>>> ---
>>>>>>> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>>>>>>> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board.h | 4 +-
>>>>>>> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>>>>>>> arch/avr32/boards/atngw100/mrmt.c | 4 +-
>>>>>>> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>>>>>>> arch/avr32/boards/atstk1000/setup.c | 2 +-
>>>>>>> arch/avr32/boards/favr-32/setup.c | 2 +-
>>>>>>> arch/avr32/boards/hammerhead/setup.c | 2 +-
>>>>>>> arch/avr32/boards/merisc/display.c | 2 +-
>>>>>>> arch/avr32/boards/mimc200/setup.c | 4 +-
>>>>>>> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>>>>>>> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>>>>>>> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>>>>>>> include/video/atmel_lcdc.h | 24 +------
>>>>>>> 21 files changed, 109 insertions(+), 101 deletions(-)
>>>>>>>
>>>>>> [snip]
>>>>>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>>>>>>> index c1a2914..98733cd4 100644
>>>>>>> --- a/drivers/video/atmel_lcdfb.c
>>>>>>> +++ b/drivers/video/atmel_lcdfb.c
>>>>>>> @@ -20,12 +20,45 @@
>>>>>>> #include <linux/gfp.h>
>>>>>>> #include <linux/module.h>
>>>>>>> #include <linux/platform_data/atmel.h>
>>>>>>> +#include <video/of_display_timing.h>
>>>>>>>
>>>>>>> #include <mach/cpu.h>
>>>>>>> #include <asm/gpio.h>
>>>>>>>
>>>>>>> #include <video/atmel_lcdc.h>
>>>>>>>
>>>>>>> +struct atmel_lcdfb_config {
>>>>>>> + bool have_alt_pixclock;
>>>>>>> + bool have_hozval;
>>>>>>> + bool have_intensity_bit;
>>>>>>> +};
>>>>>>> +
>>>>>>> + /* LCD Controller info data structure, stored in device platform_data */
>>>>>>> +struct atmel_lcdfb_info {
>>>>>>> + spinlock_t lock;
>>>>>>> + struct fb_info *info;
>>>>>>> + void __iomem *mmio;
>>>>>>> + int irq_base;
>>>>>>> + struct work_struct task;
>>>>>>> +
>>>>>>> + unsigned int smem_len;
>>>>>>> + struct platform_device *pdev;
>>>>>>> + struct clk *bus_clk;
>>>>>>> + struct clk *lcdc_clk;
>>>>>>> +
>>>>>>> + struct backlight_device *backlight;
>>>>>>> + u8 bl_power;
>>>>>>> + bool lcdcon_pol_negative;
>>>>>> I think lcdcon_pol_negative should be part of pdata, because it really
>>>>>> depends on how the PWM is wired on the board.
>>>>>>
>>>>>
>>>>> maybe but no one mainline use it on any pdata for non-dt boars
>>>>> so I did not want to expose it
>>>> Well, at least, I'm using it :)
>>>> (and I guess that Andreas is using it also, otherwise he wouldn't have
>>>> introduce it !)
>>>
>>> yes but pdata is for non-dt boards, for dt you can keep it in struct
>>> atmel_lcdfb_info and add a property
>>>
>>> if non-dt boards want it my answer is I do not care switch to DT
>>
>> ok (I use a full DT board based on sam9g35)
>>
>> so I'll add something like
>> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
>> "atmel,lcdcon-pwm-pulse-low");
>> in /atmel_lcdfb.c
>>
>> But I thought the goal of this patch was to separate driver data from
>> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
>> of the platform.
>
> You are right but as non one mainline use it as pdata I choose to drop it
> and only keep it on the driver as we can still use it for DT
>
> It's a way to force peopoe to switch to DT
well, we use it on an avr32 board (not mainlined; though no kernel
update planned currently) ... but no way to use DT currently.
Best regards
Andreas Bießmann
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 14:27 ` Andreas Bießmann
0 siblings, 0 replies; 91+ messages in thread
From: Andreas Bießmann @ 2013-05-30 14:27 UTC (permalink / raw)
To: linux-arm-kernel
On 30.05.13 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 08:39 Thu 30 May , Richard Genoud wrote:
>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>> On 19:44 Wed 29 May , Richard Genoud wrote:
>>>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>>>> On 16:36 Wed 29 May , Richard Genoud wrote:
>>>>>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
>>>>>>> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
>>>>>>> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
>>>>>>>
>>>>>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>>>>>> Cc: linux-fbdev at vger.kernel.org
>>>>>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>>>>>> Cc: Andrew Morton <akpm@linux-foundation.org>
>>>>>>> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
>>>>>>> ---
>>>>>>> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
>>>>>>> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
>>>>>>> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
>>>>>>> arch/arm/mach-at91/board.h | 4 +-
>>>>>>> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
>>>>>>> arch/avr32/boards/atngw100/mrmt.c | 4 +-
>>>>>>> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
>>>>>>> arch/avr32/boards/atstk1000/setup.c | 2 +-
>>>>>>> arch/avr32/boards/favr-32/setup.c | 2 +-
>>>>>>> arch/avr32/boards/hammerhead/setup.c | 2 +-
>>>>>>> arch/avr32/boards/merisc/display.c | 2 +-
>>>>>>> arch/avr32/boards/mimc200/setup.c | 4 +-
>>>>>>> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
>>>>>>> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
>>>>>>> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
>>>>>>> include/video/atmel_lcdc.h | 24 +------
>>>>>>> 21 files changed, 109 insertions(+), 101 deletions(-)
>>>>>>>
>>>>>> [snip]
>>>>>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
>>>>>>> index c1a2914..98733cd4 100644
>>>>>>> --- a/drivers/video/atmel_lcdfb.c
>>>>>>> +++ b/drivers/video/atmel_lcdfb.c
>>>>>>> @@ -20,12 +20,45 @@
>>>>>>> #include <linux/gfp.h>
>>>>>>> #include <linux/module.h>
>>>>>>> #include <linux/platform_data/atmel.h>
>>>>>>> +#include <video/of_display_timing.h>
>>>>>>>
>>>>>>> #include <mach/cpu.h>
>>>>>>> #include <asm/gpio.h>
>>>>>>>
>>>>>>> #include <video/atmel_lcdc.h>
>>>>>>>
>>>>>>> +struct atmel_lcdfb_config {
>>>>>>> + bool have_alt_pixclock;
>>>>>>> + bool have_hozval;
>>>>>>> + bool have_intensity_bit;
>>>>>>> +};
>>>>>>> +
>>>>>>> + /* LCD Controller info data structure, stored in device platform_data */
>>>>>>> +struct atmel_lcdfb_info {
>>>>>>> + spinlock_t lock;
>>>>>>> + struct fb_info *info;
>>>>>>> + void __iomem *mmio;
>>>>>>> + int irq_base;
>>>>>>> + struct work_struct task;
>>>>>>> +
>>>>>>> + unsigned int smem_len;
>>>>>>> + struct platform_device *pdev;
>>>>>>> + struct clk *bus_clk;
>>>>>>> + struct clk *lcdc_clk;
>>>>>>> +
>>>>>>> + struct backlight_device *backlight;
>>>>>>> + u8 bl_power;
>>>>>>> + bool lcdcon_pol_negative;
>>>>>> I think lcdcon_pol_negative should be part of pdata, because it really
>>>>>> depends on how the PWM is wired on the board.
>>>>>>
>>>>>
>>>>> maybe but no one mainline use it on any pdata for non-dt boars
>>>>> so I did not want to expose it
>>>> Well, at least, I'm using it :)
>>>> (and I guess that Andreas is using it also, otherwise he wouldn't have
>>>> introduce it !)
>>>
>>> yes but pdata is for non-dt boards, for dt you can keep it in struct
>>> atmel_lcdfb_info and add a property
>>>
>>> if non-dt boards want it my answer is I do not care switch to DT
>>
>> ok (I use a full DT board based on sam9g35)
>>
>> so I'll add something like
>> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
>> "atmel,lcdcon-pwm-pulse-low");
>> in /atmel_lcdfb.c
>>
>> But I thought the goal of this patch was to separate driver data from
>> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
>> of the platform.
>
> You are right but as non one mainline use it as pdata I choose to drop it
> and only keep it on the driver as we can still use it for DT
>
> It's a way to force peopoe to switch to DT
well, we use it on an avr32 board (not mainlined; though no kernel
update planned currently) ... but no way to use DT currently.
Best regards
Andreas Bie?mann
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
2013-05-30 14:27 ` Andreas Bießmann
(?)
@ 2013-05-30 14:59 ` Jean-Christophe PLAGNIOL-VILLARD
-1 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-30 14:59 UTC (permalink / raw)
To: Andreas Bießmann
Cc: linux-fbdev, Richard Genoud, devicetree-discuss, Nicolas Ferre,
Andreas Bießmann, Andrew Morton, linux-arm-kernel,
Hans-Christian Egtvedt
On 16:27 Thu 30 May , Andreas Bießmann wrote:
> On 30.05.13 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > On 08:39 Thu 30 May , Richard Genoud wrote:
> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>> On 19:44 Wed 29 May , Richard Genoud wrote:
> >>>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>>>> On 16:36 Wed 29 May , Richard Genoud wrote:
> >>>>>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>>>>>> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >>>>>>> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >>>>>>>
> >>>>>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >>>>>>> Cc: linux-fbdev@vger.kernel.org
> >>>>>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >>>>>>> Cc: Andrew Morton <akpm@linux-foundation.org>
> >>>>>>> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >>>>>>> ---
> >>>>>>> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >>>>>>> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board.h | 4 +-
> >>>>>>> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >>>>>>> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >>>>>>> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >>>>>>> arch/avr32/boards/atstk1000/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/favr-32/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/hammerhead/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/merisc/display.c | 2 +-
> >>>>>>> arch/avr32/boards/mimc200/setup.c | 4 +-
> >>>>>>> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >>>>>>> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >>>>>>> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >>>>>>> include/video/atmel_lcdc.h | 24 +------
> >>>>>>> 21 files changed, 109 insertions(+), 101 deletions(-)
> >>>>>>>
> >>>>>> [snip]
> >>>>>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >>>>>>> index c1a2914..98733cd4 100644
> >>>>>>> --- a/drivers/video/atmel_lcdfb.c
> >>>>>>> +++ b/drivers/video/atmel_lcdfb.c
> >>>>>>> @@ -20,12 +20,45 @@
> >>>>>>> #include <linux/gfp.h>
> >>>>>>> #include <linux/module.h>
> >>>>>>> #include <linux/platform_data/atmel.h>
> >>>>>>> +#include <video/of_display_timing.h>
> >>>>>>>
> >>>>>>> #include <mach/cpu.h>
> >>>>>>> #include <asm/gpio.h>
> >>>>>>>
> >>>>>>> #include <video/atmel_lcdc.h>
> >>>>>>>
> >>>>>>> +struct atmel_lcdfb_config {
> >>>>>>> + bool have_alt_pixclock;
> >>>>>>> + bool have_hozval;
> >>>>>>> + bool have_intensity_bit;
> >>>>>>> +};
> >>>>>>> +
> >>>>>>> + /* LCD Controller info data structure, stored in device platform_data */
> >>>>>>> +struct atmel_lcdfb_info {
> >>>>>>> + spinlock_t lock;
> >>>>>>> + struct fb_info *info;
> >>>>>>> + void __iomem *mmio;
> >>>>>>> + int irq_base;
> >>>>>>> + struct work_struct task;
> >>>>>>> +
> >>>>>>> + unsigned int smem_len;
> >>>>>>> + struct platform_device *pdev;
> >>>>>>> + struct clk *bus_clk;
> >>>>>>> + struct clk *lcdc_clk;
> >>>>>>> +
> >>>>>>> + struct backlight_device *backlight;
> >>>>>>> + u8 bl_power;
> >>>>>>> + bool lcdcon_pol_negative;
> >>>>>> I think lcdcon_pol_negative should be part of pdata, because it really
> >>>>>> depends on how the PWM is wired on the board.
> >>>>>>
> >>>>>
> >>>>> maybe but no one mainline use it on any pdata for non-dt boars
> >>>>> so I did not want to expose it
> >>>> Well, at least, I'm using it :)
> >>>> (and I guess that Andreas is using it also, otherwise he wouldn't have
> >>>> introduce it !)
> >>>
> >>> yes but pdata is for non-dt boards, for dt you can keep it in struct
> >>> atmel_lcdfb_info and add a property
> >>>
> >>> if non-dt boards want it my answer is I do not care switch to DT
> >>
> >> ok (I use a full DT board based on sam9g35)
> >>
> >> so I'll add something like
> >> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
> >> "atmel,lcdcon-pwm-pulse-low");
> >> in /atmel_lcdfb.c
> >>
> >> But I thought the goal of this patch was to separate driver data from
> >> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
> >> of the platform.
> >
> > You are right but as non one mainline use it as pdata I choose to drop it
> > and only keep it on the driver as we can still use it for DT
> >
> > It's a way to force peopoe to switch to DT
>
> well, we use it on an avr32 board (not mainlined; though no kernel
> update planned currently) ... but no way to use DT currently.
If there is 1 ARV32 user it's an other story
Best Regards,
J.
>
> Best regards
>
> Andreas Bießmann
^ permalink raw reply [flat|nested] 91+ messages in thread
* Re: [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 14:59 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-30 14:59 UTC (permalink / raw)
To: linux-arm-kernel
On 16:27 Thu 30 May , Andreas Bießmann wrote:
> On 30.05.13 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > On 08:39 Thu 30 May , Richard Genoud wrote:
> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>> On 19:44 Wed 29 May , Richard Genoud wrote:
> >>>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>>>> On 16:36 Wed 29 May , Richard Genoud wrote:
> >>>>>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>>>>>> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >>>>>>> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >>>>>>>
> >>>>>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >>>>>>> Cc: linux-fbdev@vger.kernel.org
> >>>>>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >>>>>>> Cc: Andrew Morton <akpm@linux-foundation.org>
> >>>>>>> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >>>>>>> ---
> >>>>>>> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >>>>>>> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board.h | 4 +-
> >>>>>>> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >>>>>>> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >>>>>>> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >>>>>>> arch/avr32/boards/atstk1000/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/favr-32/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/hammerhead/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/merisc/display.c | 2 +-
> >>>>>>> arch/avr32/boards/mimc200/setup.c | 4 +-
> >>>>>>> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >>>>>>> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >>>>>>> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >>>>>>> include/video/atmel_lcdc.h | 24 +------
> >>>>>>> 21 files changed, 109 insertions(+), 101 deletions(-)
> >>>>>>>
> >>>>>> [snip]
> >>>>>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >>>>>>> index c1a2914..98733cd4 100644
> >>>>>>> --- a/drivers/video/atmel_lcdfb.c
> >>>>>>> +++ b/drivers/video/atmel_lcdfb.c
> >>>>>>> @@ -20,12 +20,45 @@
> >>>>>>> #include <linux/gfp.h>
> >>>>>>> #include <linux/module.h>
> >>>>>>> #include <linux/platform_data/atmel.h>
> >>>>>>> +#include <video/of_display_timing.h>
> >>>>>>>
> >>>>>>> #include <mach/cpu.h>
> >>>>>>> #include <asm/gpio.h>
> >>>>>>>
> >>>>>>> #include <video/atmel_lcdc.h>
> >>>>>>>
> >>>>>>> +struct atmel_lcdfb_config {
> >>>>>>> + bool have_alt_pixclock;
> >>>>>>> + bool have_hozval;
> >>>>>>> + bool have_intensity_bit;
> >>>>>>> +};
> >>>>>>> +
> >>>>>>> + /* LCD Controller info data structure, stored in device platform_data */
> >>>>>>> +struct atmel_lcdfb_info {
> >>>>>>> + spinlock_t lock;
> >>>>>>> + struct fb_info *info;
> >>>>>>> + void __iomem *mmio;
> >>>>>>> + int irq_base;
> >>>>>>> + struct work_struct task;
> >>>>>>> +
> >>>>>>> + unsigned int smem_len;
> >>>>>>> + struct platform_device *pdev;
> >>>>>>> + struct clk *bus_clk;
> >>>>>>> + struct clk *lcdc_clk;
> >>>>>>> +
> >>>>>>> + struct backlight_device *backlight;
> >>>>>>> + u8 bl_power;
> >>>>>>> + bool lcdcon_pol_negative;
> >>>>>> I think lcdcon_pol_negative should be part of pdata, because it really
> >>>>>> depends on how the PWM is wired on the board.
> >>>>>>
> >>>>>
> >>>>> maybe but no one mainline use it on any pdata for non-dt boars
> >>>>> so I did not want to expose it
> >>>> Well, at least, I'm using it :)
> >>>> (and I guess that Andreas is using it also, otherwise he wouldn't have
> >>>> introduce it !)
> >>>
> >>> yes but pdata is for non-dt boards, for dt you can keep it in struct
> >>> atmel_lcdfb_info and add a property
> >>>
> >>> if non-dt boards want it my answer is I do not care switch to DT
> >>
> >> ok (I use a full DT board based on sam9g35)
> >>
> >> so I'll add something like
> >> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
> >> "atmel,lcdcon-pwm-pulse-low");
> >> in /atmel_lcdfb.c
> >>
> >> But I thought the goal of this patch was to separate driver data from
> >> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
> >> of the platform.
> >
> > You are right but as non one mainline use it as pdata I choose to drop it
> > and only keep it on the driver as we can still use it for DT
> >
> > It's a way to force peopoe to switch to DT
>
> well, we use it on an avr32 board (not mainlined; though no kernel
> update planned currently) ... but no way to use DT currently.
If there is 1 ARV32 user it's an other story
Best Regards,
J.
>
> Best regards
>
> Andreas Bießmann
^ permalink raw reply [flat|nested] 91+ messages in thread
* [PATCH 1/8] video: atmel_lcdfb: fix platform data struct
@ 2013-05-30 14:59 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 0 replies; 91+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2013-05-30 14:59 UTC (permalink / raw)
To: linux-arm-kernel
On 16:27 Thu 30 May , Andreas Bie?mann wrote:
> On 30.05.13 09:23, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > On 08:39 Thu 30 May , Richard Genoud wrote:
> >> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>> On 19:44 Wed 29 May , Richard Genoud wrote:
> >>>> 2013/5/29 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>>>> On 16:36 Wed 29 May , Richard Genoud wrote:
> >>>>>> 2013/4/11 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
> >>>>>>> Today we mix pdata and drivers data in the struct atmel_lcdfb_info
> >>>>>>> Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
> >>>>>>>
> >>>>>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> >>>>>>> Cc: linux-fbdev at vger.kernel.org
> >>>>>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> >>>>>>> Cc: Andrew Morton <akpm@linux-foundation.org>
> >>>>>>> Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
> >>>>>>> ---
> >>>>>>> arch/arm/mach-at91/at91sam9261_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9263_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9g45_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/at91sam9rl_devices.c | 6 +-
> >>>>>>> arch/arm/mach-at91/board-sam9261ek.c | 6 +-
> >>>>>>> arch/arm/mach-at91/board-sam9263ek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board-sam9m10g45ek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board-sam9rlek.c | 4 +-
> >>>>>>> arch/arm/mach-at91/board.h | 4 +-
> >>>>>>> arch/avr32/boards/atngw100/evklcd10x.c | 6 +-
> >>>>>>> arch/avr32/boards/atngw100/mrmt.c | 4 +-
> >>>>>>> arch/avr32/boards/atstk1000/atstk1000.h | 2 +-
> >>>>>>> arch/avr32/boards/atstk1000/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/favr-32/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/hammerhead/setup.c | 2 +-
> >>>>>>> arch/avr32/boards/merisc/display.c | 2 +-
> >>>>>>> arch/avr32/boards/mimc200/setup.c | 4 +-
> >>>>>>> arch/avr32/mach-at32ap/at32ap700x.c | 8 +--
> >>>>>>> arch/avr32/mach-at32ap/include/mach/board.h | 4 +-
> >>>>>>> drivers/video/atmel_lcdfb.c | 104 +++++++++++++++++----------
> >>>>>>> include/video/atmel_lcdc.h | 24 +------
> >>>>>>> 21 files changed, 109 insertions(+), 101 deletions(-)
> >>>>>>>
> >>>>>> [snip]
> >>>>>>> diff --git a/drivers/video/atmel_lcdfb.c b/drivers/video/atmel_lcdfb.c
> >>>>>>> index c1a2914..98733cd4 100644
> >>>>>>> --- a/drivers/video/atmel_lcdfb.c
> >>>>>>> +++ b/drivers/video/atmel_lcdfb.c
> >>>>>>> @@ -20,12 +20,45 @@
> >>>>>>> #include <linux/gfp.h>
> >>>>>>> #include <linux/module.h>
> >>>>>>> #include <linux/platform_data/atmel.h>
> >>>>>>> +#include <video/of_display_timing.h>
> >>>>>>>
> >>>>>>> #include <mach/cpu.h>
> >>>>>>> #include <asm/gpio.h>
> >>>>>>>
> >>>>>>> #include <video/atmel_lcdc.h>
> >>>>>>>
> >>>>>>> +struct atmel_lcdfb_config {
> >>>>>>> + bool have_alt_pixclock;
> >>>>>>> + bool have_hozval;
> >>>>>>> + bool have_intensity_bit;
> >>>>>>> +};
> >>>>>>> +
> >>>>>>> + /* LCD Controller info data structure, stored in device platform_data */
> >>>>>>> +struct atmel_lcdfb_info {
> >>>>>>> + spinlock_t lock;
> >>>>>>> + struct fb_info *info;
> >>>>>>> + void __iomem *mmio;
> >>>>>>> + int irq_base;
> >>>>>>> + struct work_struct task;
> >>>>>>> +
> >>>>>>> + unsigned int smem_len;
> >>>>>>> + struct platform_device *pdev;
> >>>>>>> + struct clk *bus_clk;
> >>>>>>> + struct clk *lcdc_clk;
> >>>>>>> +
> >>>>>>> + struct backlight_device *backlight;
> >>>>>>> + u8 bl_power;
> >>>>>>> + bool lcdcon_pol_negative;
> >>>>>> I think lcdcon_pol_negative should be part of pdata, because it really
> >>>>>> depends on how the PWM is wired on the board.
> >>>>>>
> >>>>>
> >>>>> maybe but no one mainline use it on any pdata for non-dt boars
> >>>>> so I did not want to expose it
> >>>> Well, at least, I'm using it :)
> >>>> (and I guess that Andreas is using it also, otherwise he wouldn't have
> >>>> introduce it !)
> >>>
> >>> yes but pdata is for non-dt boards, for dt you can keep it in struct
> >>> atmel_lcdfb_info and add a property
> >>>
> >>> if non-dt boards want it my answer is I do not care switch to DT
> >>
> >> ok (I use a full DT board based on sam9g35)
> >>
> >> so I'll add something like
> >> sinfo->lcdcon_pol_negative = of_property_read_bool(display_np,
> >> "atmel,lcdcon-pwm-pulse-low");
> >> in /atmel_lcdfb.c
> >>
> >> But I thought the goal of this patch was to separate driver data from
> >> platform specific data, and IMHO, lcdcon_pol_negative is a specificity
> >> of the platform.
> >
> > You are right but as non one mainline use it as pdata I choose to drop it
> > and only keep it on the driver as we can still use it for DT
> >
> > It's a way to force peopoe to switch to DT
>
> well, we use it on an avr32 board (not mainlined; though no kernel
> update planned currently) ... but no way to use DT currently.
If there is 1 ARV32 user it's an other story
Best Regards,
J.
>
> Best regards
>
> Andreas Bie?mann
^ permalink raw reply [flat|nested] 91+ messages in thread
end of thread, other threads:[~2013-05-30 14:59 UTC | newest]
Thread overview: 91+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-04-11 14:57 [PATCH 0/8] ARM: at91: atmel_lcdc: add DT support Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 14:57 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` [PATCH 1/8] video: atmel_lcdfb: fix platform data struct Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` [PATCH 2/8] video: atmel_lcdfb: introduce atmel_lcdfb_power_control Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <1365692422-9565-2-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
2013-04-16 12:35 ` Nicolas Ferre
2013-04-16 12:35 ` Nicolas Ferre
2013-04-16 12:35 ` Nicolas Ferre
2013-04-11 15:00 ` [PATCH 3/8] video: atmel_lcdfb: pass the pdata as params Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <1365692422-9565-3-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
2013-04-16 12:38 ` Nicolas Ferre
2013-04-16 12:38 ` Nicolas Ferre
2013-04-16 12:38 ` Nicolas Ferre
2013-04-11 15:00 ` [PATCH 4/8] video: atmel_lcdfb: add device tree suport Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 13:42 ` Nicolas Ferre
2013-04-16 13:42 ` Nicolas Ferre
2013-04-16 13:42 ` Nicolas Ferre
2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 13:44 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 15:43 ` Nicolas Ferre
2013-04-16 15:43 ` Nicolas Ferre
2013-04-16 15:43 ` Nicolas Ferre
[not found] ` <1365692422-9565-4-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
2013-05-29 15:01 ` Richard Genoud
2013-05-29 15:01 ` Richard Genoud
2013-05-29 15:01 ` Richard Genoud
2013-04-11 15:00 ` [PATCH 5/8] ARM: at91: sam9g45: add lcd support Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 13:57 ` Nicolas Ferre
2013-04-16 13:57 ` Nicolas Ferre
2013-04-16 14:00 ` Nicolas Ferre
2013-04-16 14:00 ` Nicolas Ferre
[not found] ` <516D5991.8020603-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
2013-04-16 15:12 ` Nicolas Ferre
2013-04-16 15:12 ` Nicolas Ferre
2013-04-11 15:00 ` [PATCH 6/8] ARM: at91: sam9263: add fb dt support Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 14:11 ` Nicolas Ferre
2013-04-16 14:11 ` Nicolas Ferre
2013-04-16 14:13 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 14:13 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 15:11 ` Nicolas Ferre
2013-04-16 15:11 ` Nicolas Ferre
2013-04-16 15:48 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 15:48 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` [PATCH 7/8] ARM: at91: at9sam9m10g45ek: add dt lcd support Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 14:56 ` Nicolas Ferre
2013-04-16 14:56 ` Nicolas Ferre
2013-04-11 15:00 ` [PATCH 8/8] ARM: at91: sam9263ek: " Jean-Christophe PLAGNIOL-VILLARD
2013-04-11 15:00 ` Jean-Christophe PLAGNIOL-VILLARD
2013-04-16 14:54 ` Nicolas Ferre
2013-04-16 14:54 ` Nicolas Ferre
2013-04-12 9:52 ` [PATCH 1/8] video: atmel_lcdfb: fix platform data struct Hans-Christian Egtvedt
2013-04-12 9:52 ` Hans-Christian Egtvedt
2013-04-12 9:52 ` Hans-Christian Egtvedt
2013-04-16 12:33 ` Nicolas Ferre
2013-04-16 12:33 ` Nicolas Ferre
2013-04-16 12:33 ` Nicolas Ferre
[not found] ` <1365692422-9565-1-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
2013-05-29 14:36 ` Richard Genoud
2013-05-29 14:36 ` Richard Genoud
2013-05-29 14:36 ` Richard Genoud
2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-29 17:35 ` Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <20130529173538.GC23899-RQcB7r2h9QmfDR2tN2SG5Ni2O/JbrIOy@public.gmane.org>
2013-05-29 17:44 ` Richard Genoud
2013-05-29 17:44 ` Richard Genoud
2013-05-29 17:44 ` Richard Genoud
[not found] ` <CACQ1gAhhsMw1-Znd8BC=A0rJBrB4pphCtH9v9qOQR+j2dY3vCw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-29 19:32 ` Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <20130529193220.GB19468-RQcB7r2h9QmfDR2tN2SG5Ni2O/JbrIOy@public.gmane.org>
2013-05-30 6:39 ` Richard Genoud
2013-05-30 6:39 ` Richard Genoud
2013-05-30 6:39 ` Richard Genoud
2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-30 7:23 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-30 14:05 ` Hans-Christian Egtvedt
2013-05-30 14:05 ` Hans-Christian Egtvedt
2013-05-30 14:05 ` Hans-Christian Egtvedt
2013-05-30 14:27 ` Andreas Bießmann
2013-05-30 14:27 ` Andreas Bießmann
2013-05-30 14:27 ` Andreas Bießmann
2013-05-30 14:59 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-30 14:59 ` Jean-Christophe PLAGNIOL-VILLARD
2013-05-30 14:59 ` Jean-Christophe PLAGNIOL-VILLARD
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.