[PATCH v2 00/15] Conversion of panel bindings to DT schema

[PATCH v2 00/15] Conversion of panel bindings to DT schema

[Rob Herring]

This series converts the common panel bindings to DT schema format. 
Besides the conversion of common panel properties, a few panel bindings 
are converted here as well. These are all the ones with references to 
panel-common.txt or panel-lvds.txt.

Rob

Rob Herring (15):
  dt-bindings: display: rockchip-lvds: Remove panel references
  dt-bindings: display: Convert common panel bindings to DT schema
  dt-bindings: display: Convert ampire,am-480272h3tmqw-t01h panel to DT
    schema
  dt-bindings: display: Convert armadeus,st0700-adapt panel to DT schema
  dt-bindings: display: Convert bananapi,s070wv20-ct16 panel to DT
    schema
  dt-bindings: display: Convert dlc,dlc0700yzg-1 panel to DT schema
  dt-bindings: display: Convert pda,91-00156-a0 panel to DT schema
  dt-bindings: display: Convert raspberrypi,7inch-touchscreen panel to
    DT schema
  dt-bindings: display: Convert tfc,s9700rtwv43tr-01b panel to DT schema
  dt-bindings: display: Convert tpo,tpg110 panel to DT schema
  dt-bindings: display: Convert panel-lvds to DT schema
  dt-bindings: display: Convert innolux,ee101ia-01 panel to DT schema
  dt-bindings: display: Convert mitsubishi,aa104xd12 panel to DT schema
  dt-bindings: display: Convert mitsubishi,aa121td01 panel to DT schema
  dt-bindings: display: Convert sgd,gktw70sdae4se panel to DT schema

 .../panel/ampire,am-480272h3tmqw-t01h.txt     |  26 ---
 .../panel/ampire,am-480272h3tmqw-t01h.yaml    |  42 +++++
 .../display/panel/arm,versatile-tft-panel.txt |   2 +-
 .../display/panel/armadeus,st0700-adapt.txt   |   9 --
 .../display/panel/armadeus,st0700-adapt.yaml  |  27 ++++
 .../display/panel/bananapi,s070wv20-ct16.txt  |  12 --
 .../display/panel/bananapi,s070wv20-ct16.yaml |  24 +++
 .../display/panel/dlc,dlc0700yzg-1.txt        |  13 --
 .../display/panel/dlc,dlc0700yzg-1.yaml       |  28 ++++
 .../display/panel/innolux,ee101ia-01d.txt     |   7 -
 .../display/panel/innolux,ee101ia-01d.yaml    |  22 +++
 .../bindings/display/panel/lvds.yaml          | 107 +++++++++++++
 .../display/panel/mitsubishi,aa104xd12.txt    |  47 ------
 .../display/panel/mitsubishi,aa104xd12.yaml   |  71 +++++++++
 .../display/panel/mitsubishi,aa121td01.txt    |  47 ------
 .../display/panel/mitsubishi,aa121td01.yaml   |  69 ++++++++
 .../bindings/display/panel/panel-common.txt   | 101 ------------
 .../bindings/display/panel/panel-common.yaml  | 149 ++++++++++++++++++
 .../bindings/display/panel/panel-lvds.txt     | 121 --------------
 .../bindings/display/panel/panel.txt          |   4 -
 .../display/panel/pda,91-00156-a0.txt         |  14 --
 .../display/panel/pda,91-00156-a0.yaml        |  25 +++
 .../panel/raspberrypi,7inch-touchscreen.txt   |  49 ------
 .../panel/raspberrypi,7inch-touchscreen.yaml  |  71 +++++++++
 .../display/panel/sgd,gktw70sdae4se.txt       |  41 -----
 .../display/panel/sgd,gktw70sdae4se.yaml      |  63 ++++++++
 .../bindings/display/panel/simple-panel.txt   |  29 +---
 .../display/panel/tfc,s9700rtwv43tr-01b.txt   |  15 --
 .../display/panel/tfc,s9700rtwv43tr-01b.yaml  |  30 ++++
 .../bindings/display/panel/tpo,tpg110.txt     |  70 --------
 .../bindings/display/panel/tpo,tpg110.yaml    | 101 ++++++++++++
 .../display/rockchip/rockchip-lvds.txt        |  11 --
 32 files changed, 831 insertions(+), 616 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml
 create mode 100644 Documentation/devicetree/bindings/display/panel/lvds.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-lvds.txt
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel.txt
 delete mode 100644 Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml

-- 
2.20.1

[PATCH v2 01/15] dt-bindings: display: rockchip-lvds: Remove panel references

[Rob Herring]

The panel bindings are outside the scope of the Rockchip LVDS interface
binding. The references are about to change too, so rather than update
them just drop the section on the panel bindings.

Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../bindings/display/rockchip/rockchip-lvds.txt       | 11 -----------
 1 file changed, 11 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt
index da6939efdb43..7849ff039229 100644
--- a/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt
+++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt
@@ -32,17 +32,6 @@ Their connections are modeled using the OF graph bindings specified in
 - video port 0 for the VOP input, the remote endpoint maybe vopb or vopl
 - video port 1 for either a panel or subsequent encoder
 
-the lvds panel described by
-	Documentation/devicetree/bindings/display/panel/simple-panel.txt
-
-Panel required properties:
-- ports for remote LVDS output
-
-Panel optional properties:
-- data-mapping: should be "vesa-24","jeida-24" or "jeida-18".
-This describes decribed by:
-	Documentation/devicetree/bindings/display/panel/panel-lvds.txt
-
 Example:
 
 lvds_panel: lvds-panel {
-- 
2.20.1

[PATCH v2 02/15] dt-bindings: display: Convert common panel bindings to DT schema

Convert the common panel bindings to DT schema consolidating scattered
definitions to a single schema file.

The 'simple-panel' binding just a collection of properties and not a
complete binding itself. All of the 'simple-panel' properties are
covered by the panel-common.txt binding with the exception of the
'no-hpd' property, so add that to the schema.

As there are lots of references to simple-panel.txt, just keep the file
with a reference to common.yaml for now until all the bindings are
converted.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/arm,versatile-tft-panel.txt |   2 +-
 .../bindings/display/panel/panel-common.txt   | 101 ------------
 .../bindings/display/panel/panel-common.yaml  | 149 ++++++++++++++++++
 .../bindings/display/panel/panel.txt          |   4 -
 .../bindings/display/panel/simple-panel.txt   |  29 +---
 5 files changed, 151 insertions(+), 134 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel.txt

diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
index 248141c3c7e3..0601a9e34703 100644
--- a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
@@ -10,7 +10,7 @@ Required properties:
 - compatible: should be "arm,versatile-tft-panel"
 
 Required subnodes:
-- port: see display/panel/panel-common.txt, graph.txt
+- port: see display/panel/panel-common.yaml, graph.txt
 
 
 Example:
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt
deleted file mode 100644
index 5d2519af4bb5..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel-common.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-Common Properties for Display Panel
-===================================
-
-This document defines device tree properties common to several classes of
-display panels. It doesn't constitue a device tree binding specification by
-itself but is meant to be referenced by device tree bindings.
-
-When referenced from panel device tree bindings the properties defined in this
-document are defined as follows. The panel device tree bindings are
-responsible for defining whether each property is required or optional.
-
-
-Descriptive Properties
-----------------------
-
-- width-mm,
-- height-mm: The width-mm and height-mm specify the width and height of the
-  physical area where images are displayed. These properties are expressed in
-  millimeters and rounded to the closest unit.
-
-- label: The label property specifies a symbolic name for the panel as a
-  string suitable for use by humans. It typically contains a name inscribed on
-  the system (e.g. as an affixed label) or specified in the system's
-  documentation (e.g. in the user's manual).
-
-  If no such name exists, and unless the property is mandatory according to
-  device tree bindings, it shall rather be omitted than constructed of
-  non-descriptive information. For instance an LCD panel in a system that
-  contains a single panel shall not be labelled "LCD" if that name is not
-  inscribed on the system or used in a descriptive fashion in system
-  documentation.
-
-
-Display Timings
----------------
-
-- panel-timing: Most display panels are restricted to a single resolution and
-  require specific display timings. The panel-timing subnode expresses those
-  timings as specified in the timing subnode section of the display timing
-  bindings defined in
-  Documentation/devicetree/bindings/display/panel/display-timing.txt.
-
-
-Connectivity
-------------
-
-- ports: Panels receive video data through one or multiple connections. While
-  the nature of those connections is specific to the panel type, the
-  connectivity is expressed in a standard fashion using ports as specified in
-  the device graph bindings defined in
-  Documentation/devicetree/bindings/graph.txt.
-
-- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible
-  bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
-  phandle to the system I2C controller connected to that bus.
-
-
-Control I/Os
-------------
-
-Many display panels can be controlled through pins driven by GPIOs. The nature
-and timing of those control signals are device-specific and left for panel
-device tree bindings to specify. The following GPIO specifiers can however be
-used for panels that implement compatible control signals.
-
-- enable-gpios: Specifier for a GPIO connected to the panel enable control
-  signal. The enable signal is active high and enables operation of the panel.
-  This property can also be used for panels implementing an active low power
-  down signal, which is a negated version of the enable signal. Active low
-  enable signals (or active high power down signals) can be supported by
-  inverting the GPIO specifier polarity flag.
-
-  Note that the enable signal control panel operation only and must not be
-  confused with a backlight enable signal.
-
-- reset-gpios: Specifier for a GPIO coonnected to the panel reset control
-  signal. The reset signal is active low and resets the panel internal logic
-  while active. Active high reset signals can be supported by inverting the
-  GPIO specifier polarity flag.
-
-Power
------
-
-- power-supply: display panels require power to be supplied. While several
-  panels need more than one power supply with panel-specific constraints
-  governing the order and timings of the power supplies, in many cases a single
-  power supply is sufficient, either because the panel has a single power rail,
-  or because all its power rails can be driven by the same supply. In that case
-  the power-supply property specifies the supply powering the panel as a phandle
-  to a regulator.
-
-Backlight
----------
-
-Most display panels include a backlight. Some of them also include a backlight
-controller exposed through a control bus such as I2C or DSI. Others expose
-backlight control through GPIO, PWM or other signals connected to an external
-backlight controller.
-
-- backlight: For panels whose backlight is controlled by an external backlight
-  controller, this property contains a phandle that references the controller.
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
new file mode 100644
index 000000000000..ef8d8cdfcede
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
@@ -0,0 +1,149 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/panel-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common Properties for Display Panels
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  This document defines device tree properties common to several classes of
+  display panels. It doesn't constitue a device tree binding specification by
+  itself but is meant to be referenced by device tree bindings.
+
+  When referenced from panel device tree bindings the properties defined in this
+  document are defined as follows. The panel device tree bindings are
+  responsible for defining whether each property is required or optional.
+
+properties:
+  # Descriptive Properties
+  width-mm:
+    description:
+      Specifies the width of the physical area where images are displayed. This
+      property is expressed in millimeters and rounded to the closest unit.
+
+  height-mm:
+    description:
+      Specifies the height of the physical area where images are displayed. This
+      property is expressed in millimeters and rounded to the closest unit.
+
+  label:
+    description: |
+      The label property specifies a symbolic name for the panel as a
+      string suitable for use by humans. It typically contains a name inscribed
+      on the system (e.g. as an affixed label) or specified in the system's
+      documentation (e.g. in the user's manual).
+
+      If no such name exists, and unless the property is mandatory according to
+      device tree bindings, it shall rather be omitted than constructed of
+      non-descriptive information. For instance an LCD panel in a system that
+      contains a single panel shall not be labelled "LCD" if that name is not
+      inscribed on the system or used in a descriptive fashion in system
+      documentation.
+
+  rotation:
+    description:
+      Display rotation in degrees counter clockwise (0,90,180,270)
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 90, 180, 270 ]
+
+  # Display Timings
+  panel-timing:
+    type: object
+    description:
+      Most display panels are restricted to a single resolution and
+      require specific display timings. The panel-timing subnode expresses those
+      timings as specified in the timing subnode section of the display timing
+      bindings defined in
+      Documentation/devicetree/bindings/display/panel/display-timing.txt.
+
+  # Connectivity
+  port:
+    type: object
+
+  ports:
+    type: object
+    description:
+      Panels receive video data through one or multiple connections. While
+      the nature of those connections is specific to the panel type, the
+      connectivity is expressed in a standard fashion using ports as specified
+      in the device graph bindings defined in
+      Documentation/devicetree/bindings/graph.txt.
+
+  ddc-i2c-bus:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Some panels expose EDID information through an I2C-compatible
+      bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
+      phandle to the system I2C controller connected to that bus.
+
+  no-hpd:
+    type: boolean
+    description:
+      This panel is supposed to communicate that it's ready via HPD
+      (hot plug detect) signal, but the signal isn't hooked up so we should
+      hardcode the max delay from the panel spec when powering up the panel.
+
+  # Control I/Os
+
+  # Many display panels can be controlled through pins driven by GPIOs. The nature
+  # and timing of those control signals are device-specific and left for panel
+  # device tree bindings to specify. The following GPIO specifiers can however be
+  # used for panels that implement compatible control signals.
+
+  enable-gpios:
+    maxItems: 1
+    description: |
+      Specifier for a GPIO connected to the panel enable control signal. The
+      enable signal is active high and enables operation of the panel. This
+      property can also be used for panels implementing an active low power down
+      signal, which is a negated version of the enable signal. Active low enable
+      signals (or active high power down signals) can be supported by inverting
+      the GPIO specifier polarity flag.
+
+      Note that the enable signal control panel operation only and must not be
+      confused with a backlight enable signal.
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      Specifier for a GPIO connected to the panel reset control signal.
+      The reset signal is active low and resets the panel internal logic
+      while active. Active high reset signals can be supported by inverting the
+      GPIO specifier polarity flag.
+
+  # Power
+  power-supply:
+    description:
+      Display panels require power to be supplied. While several panels need
+      more than one power supply with panel-specific constraints governing the
+      order and timings of the power supplies, in many cases a single power
+      supply is sufficient, either because the panel has a single power rail, or
+      because all its power rails can be driven by the same supply. In that case
+      the power-supply property specifies the supply powering the panel as a
+      phandle to a regulator.
+
+  # Backlight
+
+  # Most display panels include a backlight. Some of them also include a backlight
+  # controller exposed through a control bus such as I2C or DSI. Others expose
+  # backlight control through GPIO, PWM or other signals connected to an external
+  # backlight controller.
+
+  backlight:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      For panels whose backlight is controlled by an external backlight
+      controller, this property contains a phandle that references the
+      controller.
+
+dependencies:
+  width-mm: [ height-mm ]
+  height-mm: [ width-mm ]
+
+...
diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt
deleted file mode 100644
index e2e6867852b8..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel.txt
+++ /dev/null
@@ -1,4 +0,0 @@
-Common display properties
--------------------------
-
-- rotation:	Display rotation in degrees counter clockwise (0,90,180,270)
diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
index b2b872c710f2..e11208fb7da8 100644
--- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
@@ -1,28 +1 @@
-Simple display panel
-====================
-
-panel node
-----------
-
-Required properties:
-- power-supply: See panel-common.txt
-
-Optional properties:
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-- no-hpd: This panel is supposed to communicate that it's ready via HPD
-  (hot plug detect) signal, but the signal isn't hooked up so we should
-  hardcode the max delay from the panel spec when powering up the panel.
-
-Example:
-
-	panel: panel {
-		compatible = "cptt,claa101wb01";
-		ddc-i2c-bus = <&panelddc>;
-
-		power-supply = <&vdd_pnl_reg>;
-		enable-gpios = <&gpio 90 0>;
-
-		backlight = <&backlight>;
-	};
+See panel-common.yaml in this directory.
-- 
2.20.1

[PATCH v2 02/15] dt-bindings: display: Convert common panel bindings to DT schema

[Rob Herring]

Convert the common panel bindings to DT schema consolidating scattered
definitions to a single schema file.

The 'simple-panel' binding just a collection of properties and not a
complete binding itself. All of the 'simple-panel' properties are
covered by the panel-common.txt binding with the exception of the
'no-hpd' property, so add that to the schema.

As there are lots of references to simple-panel.txt, just keep the file
with a reference to common.yaml for now until all the bindings are
converted.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/arm,versatile-tft-panel.txt |   2 +-
 .../bindings/display/panel/panel-common.txt   | 101 ------------
 .../bindings/display/panel/panel-common.yaml  | 149 ++++++++++++++++++
 .../bindings/display/panel/panel.txt          |   4 -
 .../bindings/display/panel/simple-panel.txt   |  29 +---
 5 files changed, 151 insertions(+), 134 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/panel-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel.txt

diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
index 248141c3c7e3..0601a9e34703 100644
--- a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.txt
@@ -10,7 +10,7 @@ Required properties:
 - compatible: should be "arm,versatile-tft-panel"
 
 Required subnodes:
-- port: see display/panel/panel-common.txt, graph.txt
+- port: see display/panel/panel-common.yaml, graph.txt
 
 
 Example:
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt
deleted file mode 100644
index 5d2519af4bb5..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel-common.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-Common Properties for Display Panel
-===================================
-
-This document defines device tree properties common to several classes of
-display panels. It doesn't constitue a device tree binding specification by
-itself but is meant to be referenced by device tree bindings.
-
-When referenced from panel device tree bindings the properties defined in this
-document are defined as follows. The panel device tree bindings are
-responsible for defining whether each property is required or optional.
-
-
-Descriptive Properties
-----------------------
-
-- width-mm,
-- height-mm: The width-mm and height-mm specify the width and height of the
-  physical area where images are displayed. These properties are expressed in
-  millimeters and rounded to the closest unit.
-
-- label: The label property specifies a symbolic name for the panel as a
-  string suitable for use by humans. It typically contains a name inscribed on
-  the system (e.g. as an affixed label) or specified in the system's
-  documentation (e.g. in the user's manual).
-
-  If no such name exists, and unless the property is mandatory according to
-  device tree bindings, it shall rather be omitted than constructed of
-  non-descriptive information. For instance an LCD panel in a system that
-  contains a single panel shall not be labelled "LCD" if that name is not
-  inscribed on the system or used in a descriptive fashion in system
-  documentation.
-
-
-Display Timings
----------------
-
-- panel-timing: Most display panels are restricted to a single resolution and
-  require specific display timings. The panel-timing subnode expresses those
-  timings as specified in the timing subnode section of the display timing
-  bindings defined in
-  Documentation/devicetree/bindings/display/panel/display-timing.txt.
-
-
-Connectivity
-------------
-
-- ports: Panels receive video data through one or multiple connections. While
-  the nature of those connections is specific to the panel type, the
-  connectivity is expressed in a standard fashion using ports as specified in
-  the device graph bindings defined in
-  Documentation/devicetree/bindings/graph.txt.
-
-- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible
-  bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
-  phandle to the system I2C controller connected to that bus.
-
-
-Control I/Os
-------------
-
-Many display panels can be controlled through pins driven by GPIOs. The nature
-and timing of those control signals are device-specific and left for panel
-device tree bindings to specify. The following GPIO specifiers can however be
-used for panels that implement compatible control signals.
-
-- enable-gpios: Specifier for a GPIO connected to the panel enable control
-  signal. The enable signal is active high and enables operation of the panel.
-  This property can also be used for panels implementing an active low power
-  down signal, which is a negated version of the enable signal. Active low
-  enable signals (or active high power down signals) can be supported by
-  inverting the GPIO specifier polarity flag.
-
-  Note that the enable signal control panel operation only and must not be
-  confused with a backlight enable signal.
-
-- reset-gpios: Specifier for a GPIO coonnected to the panel reset control
-  signal. The reset signal is active low and resets the panel internal logic
-  while active. Active high reset signals can be supported by inverting the
-  GPIO specifier polarity flag.
-
-Power
------
-
-- power-supply: display panels require power to be supplied. While several
-  panels need more than one power supply with panel-specific constraints
-  governing the order and timings of the power supplies, in many cases a single
-  power supply is sufficient, either because the panel has a single power rail,
-  or because all its power rails can be driven by the same supply. In that case
-  the power-supply property specifies the supply powering the panel as a phandle
-  to a regulator.
-
-Backlight
----------
-
-Most display panels include a backlight. Some of them also include a backlight
-controller exposed through a control bus such as I2C or DSI. Others expose
-backlight control through GPIO, PWM or other signals connected to an external
-backlight controller.
-
-- backlight: For panels whose backlight is controlled by an external backlight
-  controller, this property contains a phandle that references the controller.
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.yaml b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
new file mode 100644
index 000000000000..ef8d8cdfcede
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/panel-common.yaml
@@ -0,0 +1,149 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/panel-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common Properties for Display Panels
+
+maintainers:
+  - Thierry Reding <thierry.reding@gmail.com>
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  This document defines device tree properties common to several classes of
+  display panels. It doesn't constitue a device tree binding specification by
+  itself but is meant to be referenced by device tree bindings.
+
+  When referenced from panel device tree bindings the properties defined in this
+  document are defined as follows. The panel device tree bindings are
+  responsible for defining whether each property is required or optional.
+
+properties:
+  # Descriptive Properties
+  width-mm:
+    description:
+      Specifies the width of the physical area where images are displayed. This
+      property is expressed in millimeters and rounded to the closest unit.
+
+  height-mm:
+    description:
+      Specifies the height of the physical area where images are displayed. This
+      property is expressed in millimeters and rounded to the closest unit.
+
+  label:
+    description: |
+      The label property specifies a symbolic name for the panel as a
+      string suitable for use by humans. It typically contains a name inscribed
+      on the system (e.g. as an affixed label) or specified in the system's
+      documentation (e.g. in the user's manual).
+
+      If no such name exists, and unless the property is mandatory according to
+      device tree bindings, it shall rather be omitted than constructed of
+      non-descriptive information. For instance an LCD panel in a system that
+      contains a single panel shall not be labelled "LCD" if that name is not
+      inscribed on the system or used in a descriptive fashion in system
+      documentation.
+
+  rotation:
+    description:
+      Display rotation in degrees counter clockwise (0,90,180,270)
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 90, 180, 270 ]
+
+  # Display Timings
+  panel-timing:
+    type: object
+    description:
+      Most display panels are restricted to a single resolution and
+      require specific display timings. The panel-timing subnode expresses those
+      timings as specified in the timing subnode section of the display timing
+      bindings defined in
+      Documentation/devicetree/bindings/display/panel/display-timing.txt.
+
+  # Connectivity
+  port:
+    type: object
+
+  ports:
+    type: object
+    description:
+      Panels receive video data through one or multiple connections. While
+      the nature of those connections is specific to the panel type, the
+      connectivity is expressed in a standard fashion using ports as specified
+      in the device graph bindings defined in
+      Documentation/devicetree/bindings/graph.txt.
+
+  ddc-i2c-bus:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Some panels expose EDID information through an I2C-compatible
+      bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
+      phandle to the system I2C controller connected to that bus.
+
+  no-hpd:
+    type: boolean
+    description:
+      This panel is supposed to communicate that it's ready via HPD
+      (hot plug detect) signal, but the signal isn't hooked up so we should
+      hardcode the max delay from the panel spec when powering up the panel.
+
+  # Control I/Os
+
+  # Many display panels can be controlled through pins driven by GPIOs. The nature
+  # and timing of those control signals are device-specific and left for panel
+  # device tree bindings to specify. The following GPIO specifiers can however be
+  # used for panels that implement compatible control signals.
+
+  enable-gpios:
+    maxItems: 1
+    description: |
+      Specifier for a GPIO connected to the panel enable control signal. The
+      enable signal is active high and enables operation of the panel. This
+      property can also be used for panels implementing an active low power down
+      signal, which is a negated version of the enable signal. Active low enable
+      signals (or active high power down signals) can be supported by inverting
+      the GPIO specifier polarity flag.
+
+      Note that the enable signal control panel operation only and must not be
+      confused with a backlight enable signal.
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      Specifier for a GPIO connected to the panel reset control signal.
+      The reset signal is active low and resets the panel internal logic
+      while active. Active high reset signals can be supported by inverting the
+      GPIO specifier polarity flag.
+
+  # Power
+  power-supply:
+    description:
+      Display panels require power to be supplied. While several panels need
+      more than one power supply with panel-specific constraints governing the
+      order and timings of the power supplies, in many cases a single power
+      supply is sufficient, either because the panel has a single power rail, or
+      because all its power rails can be driven by the same supply. In that case
+      the power-supply property specifies the supply powering the panel as a
+      phandle to a regulator.
+
+  # Backlight
+
+  # Most display panels include a backlight. Some of them also include a backlight
+  # controller exposed through a control bus such as I2C or DSI. Others expose
+  # backlight control through GPIO, PWM or other signals connected to an external
+  # backlight controller.
+
+  backlight:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      For panels whose backlight is controlled by an external backlight
+      controller, this property contains a phandle that references the
+      controller.
+
+dependencies:
+  width-mm: [ height-mm ]
+  height-mm: [ width-mm ]
+
+...
diff --git a/Documentation/devicetree/bindings/display/panel/panel.txt b/Documentation/devicetree/bindings/display/panel/panel.txt
deleted file mode 100644
index e2e6867852b8..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel.txt
+++ /dev/null
@@ -1,4 +0,0 @@
-Common display properties
--------------------------
-
-- rotation:	Display rotation in degrees counter clockwise (0,90,180,270)
diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
index b2b872c710f2..e11208fb7da8 100644
--- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
@@ -1,28 +1 @@
-Simple display panel
-====================
-
-panel node
-----------
-
-Required properties:
-- power-supply: See panel-common.txt
-
-Optional properties:
-- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-- no-hpd: This panel is supposed to communicate that it's ready via HPD
-  (hot plug detect) signal, but the signal isn't hooked up so we should
-  hardcode the max delay from the panel spec when powering up the panel.
-
-Example:
-
-	panel: panel {
-		compatible = "cptt,claa101wb01";
-		ddc-i2c-bus = <&panelddc>;
-
-		power-supply = <&vdd_pnl_reg>;
-		enable-gpios = <&gpio 90 0>;
-
-		backlight = <&backlight>;
-	};
+See panel-common.yaml in this directory.
-- 
2.20.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 03/15] dt-bindings: display: Convert ampire,am-480272h3tmqw-t01h panel to DT schema

[Rob Herring]

Convert the ampire,am-480272h3tmqw-t01h panel binding to DT schema.

Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../panel/ampire,am-480272h3tmqw-t01h.txt     | 26 ------------
 .../panel/ampire,am-480272h3tmqw-t01h.yaml    | 42 +++++++++++++++++++
 2 files changed, 42 insertions(+), 26 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
deleted file mode 100644
index 6812280cb109..000000000000
--- a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
+++ /dev/null
@@ -1,26 +0,0 @@
-Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
-
-Required properties:
-- compatible: should be "ampire,am-480272h3tmqw-t01h"
-
-Optional properties:
-- power-supply: regulator to provide the supply voltage
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-
-Optional nodes:
-- Video port for RGB input.
-
-Example:
-	panel_rgb: panel-rgb {
-		compatible = "ampire,am-480272h3tmqw-t01h";
-		enable-gpios = <&gpioa 8 1>;
-		port {
-			panel_in_rgb: endpoint {
-				remote-endpoint = <&controller_out_rgb>;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml
new file mode 100644
index 000000000000..c6e33e7f36d0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ampire,am-480272h3tmqw-t01h.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel
+
+maintainers:
+  - Yannick Fertre <yannick.fertre@st.com>
+  - Thierry Reding <treding@nvidia.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: ampire,am-480272h3tmqw-t01h
+
+  power-supply: true
+  enable-gpios: true
+  backlight: true
+  port: true
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    panel_rgb: panel {
+      compatible = "ampire,am-480272h3tmqw-t01h";
+      enable-gpios = <&gpioa 8 1>;
+      port {
+        panel_in_rgb: endpoint {
+          remote-endpoint = <&controller_out_rgb>;
+        };
+      };
+    };
+
+...
-- 
2.20.1

[PATCH v2 03/15] dt-bindings: display: Convert ampire, am-480272h3tmqw-t01h panel to DT schema

[Rob Herring]

Convert the ampire,am-480272h3tmqw-t01h panel binding to DT schema.

Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../panel/ampire,am-480272h3tmqw-t01h.txt     | 26 ------------
 .../panel/ampire,am-480272h3tmqw-t01h.yaml    | 42 +++++++++++++++++++
 2 files changed, 42 insertions(+), 26 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
deleted file mode 100644
index 6812280cb109..000000000000
--- a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.txt
+++ /dev/null
@@ -1,26 +0,0 @@
-Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
-
-Required properties:
-- compatible: should be "ampire,am-480272h3tmqw-t01h"
-
-Optional properties:
-- power-supply: regulator to provide the supply voltage
-- enable-gpios: GPIO pin to enable or disable the panel
-- backlight: phandle of the backlight device attached to the panel
-
-Optional nodes:
-- Video port for RGB input.
-
-Example:
-	panel_rgb: panel-rgb {
-		compatible = "ampire,am-480272h3tmqw-t01h";
-		enable-gpios = <&gpioa 8 1>;
-		port {
-			panel_in_rgb: endpoint {
-				remote-endpoint = <&controller_out_rgb>;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml
new file mode 100644
index 000000000000..c6e33e7f36d0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ampire,am-480272h3tmqw-t01h.yaml
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ampire,am-480272h3tmqw-t01h.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ampire AM-480272H3TMQW-T01H 4.3" WQVGA TFT LCD panel
+
+maintainers:
+  - Yannick Fertre <yannick.fertre@st.com>
+  - Thierry Reding <treding@nvidia.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: ampire,am-480272h3tmqw-t01h
+
+  power-supply: true
+  enable-gpios: true
+  backlight: true
+  port: true
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    panel_rgb: panel {
+      compatible = "ampire,am-480272h3tmqw-t01h";
+      enable-gpios = <&gpioa 8 1>;
+      port {
+        panel_in_rgb: endpoint {
+          remote-endpoint = <&controller_out_rgb>;
+        };
+      };
+    };
+
+...
-- 
2.20.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 04/15] dt-bindings: display: Convert armadeus,st0700-adapt panel to DT schema

[Rob Herring]

Convert the armadeus,st0700-adapt panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/armadeus,st0700-adapt.txt   |  9 -------
 .../display/panel/armadeus,st0700-adapt.yaml  | 27 +++++++++++++++++++
 2 files changed, 27 insertions(+), 9 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
deleted file mode 100644
index a30d63db3c8f..000000000000
--- a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
+++ /dev/null
@@ -1,9 +0,0 @@
-Armadeus ST0700 Adapt. A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with
-an adapter board.
-
-Required properties:
-- compatible: "armadeus,st0700-adapt"
-- power-supply: see panel-common.txt
-
-Optional properties:
-- backlight: see panel-common.txt
diff --git a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml
new file mode 100644
index 000000000000..59376669442a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml
@@ -0,0 +1,27 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/armadeus,st0700-adapt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Armadeus ST0700 Adapter
+
+description:
+  A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with an adapter board.
+
+maintainers:
+  - '"Sébastien Szymanski" <sebastien.szymanski@armadeus.com>'
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: armadeus,st0700-adapt
+
+required:
+  - compatible
+  - power-supply
+
+...
-- 
2.20.1

[PATCH v2 04/15] dt-bindings: display: Convert armadeus, st0700-adapt panel to DT schema

[Rob Herring]

Convert the armadeus,st0700-adapt panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/armadeus,st0700-adapt.txt   |  9 -------
 .../display/panel/armadeus,st0700-adapt.yaml  | 27 +++++++++++++++++++
 2 files changed, 27 insertions(+), 9 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
deleted file mode 100644
index a30d63db3c8f..000000000000
--- a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.txt
+++ /dev/null
@@ -1,9 +0,0 @@
-Armadeus ST0700 Adapt. A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with
-an adapter board.
-
-Required properties:
-- compatible: "armadeus,st0700-adapt"
-- power-supply: see panel-common.txt
-
-Optional properties:
-- backlight: see panel-common.txt
diff --git a/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml
new file mode 100644
index 000000000000..59376669442a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/armadeus,st0700-adapt.yaml
@@ -0,0 +1,27 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/armadeus,st0700-adapt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Armadeus ST0700 Adapter
+
+description:
+  A Santek ST0700I5Y-RBSLW 7.0" WVGA (800x480) TFT with an adapter board.
+
+maintainers:
+  - '"Sébastien Szymanski" <sebastien.szymanski@armadeus.com>'
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: armadeus,st0700-adapt
+
+required:
+  - compatible
+  - power-supply
+
+...
-- 
2.20.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 05/15] dt-bindings: display: Convert bananapi,s070wv20-ct16 panel to DT schema

[Rob Herring]

Convert the bananapi,s070wv20-ct16 panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/bananapi,s070wv20-ct16.txt  | 12 ----------
 .../display/panel/bananapi,s070wv20-ct16.yaml | 24 +++++++++++++++++++
 2 files changed, 24 insertions(+), 12 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
deleted file mode 100644
index 35bc0c839f49..000000000000
--- a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.txt
+++ /dev/null
@@ -1,12 +0,0 @@
-Banana Pi 7" (S070WV20-CT16) TFT LCD Panel
-
-Required properties:
-- compatible: should be "bananapi,s070wv20-ct16"
-- power-supply: see ./panel-common.txt
-
-Optional properties:
-- enable-gpios: see ./simple-panel.txt
-- backlight: see ./simple-panel.txt
-
-This binding is compatible with the simple-panel binding, which is specified
-in ./simple-panel.txt.
diff --git a/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml
new file mode 100644
index 000000000000..2c1d3bf2baa0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/bananapi,s070wv20-ct16.yaml
@@ -0,0 +1,24 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/bananapi,s070wv20-ct16.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Banana Pi 7" (S070WV20-CT16) TFT LCD Panel
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: bananapi,s070wv20-ct16
+
+required:
+  - compatible
+  - power-supply
+
+...
-- 
2.20.1

[PATCH v2 06/15] dt-bindings: display: Convert dlc,dlc0700yzg-1 panel to DT schema

[Rob Herring]

Convert the dlc,dlc0700yzg-1 panel binding to DT schema.

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/dlc,dlc0700yzg-1.txt        | 13 ---------
 .../display/panel/dlc,dlc0700yzg-1.yaml       | 28 +++++++++++++++++++
 2 files changed, 28 insertions(+), 13 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
deleted file mode 100644
index bf06bb025b08..000000000000
--- a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
+++ /dev/null
@@ -1,13 +0,0 @@
-DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "dlc,dlc0700yzg-1"
-- power-supply: See simple-panel.txt
-
-Optional properties:
-- reset-gpios: See panel-common.txt
-- enable-gpios: See simple-panel.txt
-- backlight: See simple-panel.txt
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
new file mode 100644
index 000000000000..1b0b63d46f3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
@@ -0,0 +1,28 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
+
+maintainers:
+  - Philipp Zabel <p.zabel@pengutronix.de>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: dlc,dlc0700yzg-1
+
+  reset-gpios: true
+  enable-gpios: true
+  backlight: true
+
+required:
+  - compatible
+  - power-supply
+
+...
-- 
2.20.1

[PATCH v2 07/15] dt-bindings: display: Convert pda,91-00156-a0 panel to DT schema

[Rob Herring]

Convert the pda,91-00156-a0 panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/pda,91-00156-a0.txt         | 14 -----------
 .../display/panel/pda,91-00156-a0.yaml        | 25 +++++++++++++++++++
 2 files changed, 25 insertions(+), 14 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
deleted file mode 100644
index 1639fb17a9f0..000000000000
--- a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
+++ /dev/null
@@ -1,14 +0,0 @@
-PDA 91-00156-A0 5.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "pda,91-00156-a0"
-- power-supply: this panel requires a single power supply. A phandle to a
-regulator needs to be specified here. Compatible with panel-common binding which
-is specified in the panel-common.txt in this directory.
-- backlight: this panel's backlight is controlled by an external backlight
-controller. A phandle to this controller needs to be specified here.
-Compatible with panel-common binding which is specified in the panel-common.txt
-in this directory.
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml
new file mode 100644
index 000000000000..cea5bcb3c455
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/pda,91-00156-a0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PDA 91-00156-A0 5.0" WVGA TFT LCD panel
+
+maintainers:
+  - Cristian Birsan <cristian.birsan@microchip.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: pda,91-00156-a0
+
+required:
+  - compatible
+  - power-supply
+  - backlight
+
+...
-- 
2.20.1

[PATCH v2 07/15] dt-bindings: display: Convert pda, 91-00156-a0 panel to DT schema

[Rob Herring]

Convert the pda,91-00156-a0 panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/pda,91-00156-a0.txt         | 14 -----------
 .../display/panel/pda,91-00156-a0.yaml        | 25 +++++++++++++++++++
 2 files changed, 25 insertions(+), 14 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
deleted file mode 100644
index 1639fb17a9f0..000000000000
--- a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.txt
+++ /dev/null
@@ -1,14 +0,0 @@
-PDA 91-00156-A0 5.0" WVGA TFT LCD panel
-
-Required properties:
-- compatible: should be "pda,91-00156-a0"
-- power-supply: this panel requires a single power supply. A phandle to a
-regulator needs to be specified here. Compatible with panel-common binding which
-is specified in the panel-common.txt in this directory.
-- backlight: this panel's backlight is controlled by an external backlight
-controller. A phandle to this controller needs to be specified here.
-Compatible with panel-common binding which is specified in the panel-common.txt
-in this directory.
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml
new file mode 100644
index 000000000000..cea5bcb3c455
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/pda,91-00156-a0.yaml
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/pda,91-00156-a0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PDA 91-00156-A0 5.0" WVGA TFT LCD panel
+
+maintainers:
+  - Cristian Birsan <cristian.birsan@microchip.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: pda,91-00156-a0
+
+required:
+  - compatible
+  - power-supply
+  - backlight
+
+...
-- 
2.20.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 08/15] dt-bindings: display: Convert raspberrypi,7inch-touchscreen panel to DT schema

[Rob Herring]

Convert the raspberrypi,7inch-touchscreen panel binding to DT schema.

Cc: Eric Anholt <eric@anholt.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../panel/raspberrypi,7inch-touchscreen.txt   | 49 -------------
 .../panel/raspberrypi,7inch-touchscreen.yaml  | 71 +++++++++++++++++++
 2 files changed, 71 insertions(+), 49 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
deleted file mode 100644
index e9e19c059260..000000000000
--- a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
+++ /dev/null
@@ -1,49 +0,0 @@
-This binding covers the official 7" (800x480) Raspberry Pi touchscreen
-panel.
-
-This DSI panel contains:
-
-- TC358762 DSI->DPI bridge
-- Atmel microcontroller on I2C for power sequencing the DSI bridge and
-  controlling backlight
-- Touchscreen controller on I2C for touch input
-
-and this binding covers the DSI display parts but not its touch input.
-
-Required properties:
-- compatible:	Must be "raspberrypi,7inch-touchscreen-panel"
-- reg:		Must be "45"
-- port:		See panel-common.txt
-
-Example:
-
-dsi1: dsi@7e700000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	<...>
-
-	port {
-		dsi_out_port: endpoint {
-			remote-endpoint = <&panel_dsi_port>;
-		};
-	};
-};
-
-i2c_dsi: i2c {
-	compatible = "i2c-gpio";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	gpios = <&gpio 28 0
-		 &gpio 29 0>;
-
-	lcd@45 {
-		compatible = "raspberrypi,7inch-touchscreen-panel";
-		reg = <0x45>;
-
-		port {
-			panel_dsi_port: endpoint {
-				remote-endpoint = <&dsi_out_port>;
-			};
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml
new file mode 100644
index 000000000000..22a083f7bc8e
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/raspberrypi,7inch-touchscreen.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: The official 7" (800x480) Raspberry Pi touchscreen
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+description: |+
+  This DSI panel contains:
+
+  - TC358762 DSI->DPI bridge
+  - Atmel microcontroller on I2C for power sequencing the DSI bridge and
+    controlling backlight
+  - Touchscreen controller on I2C for touch input
+
+  and this binding covers the DSI display parts but not its touch input.
+
+properties:
+  compatible:
+    const: raspberrypi,7inch-touchscreen-panel
+
+  reg:
+    const: 0x45
+
+  port: true
+
+required:
+  - compatible
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |+
+    dsi1: dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      port {
+        dsi_out_port: endpoint {
+          remote-endpoint = <&panel_dsi_port>;
+        };
+      };
+    };
+
+    i2c_dsi: i2c {
+      compatible = "i2c-gpio";
+      #address-cells = <1>;
+      #size-cells = <0>;
+      scl-gpios = <&gpio 28 0>;
+      sda-gpios = <&gpio 29 0>;
+
+      lcd@45 {
+        compatible = "raspberrypi,7inch-touchscreen-panel";
+        reg = <0x45>;
+
+        port {
+          panel_dsi_port: endpoint {
+            remote-endpoint = <&dsi_out_port>;
+          };
+        };
+      };
+    };
+
+...
-- 
2.20.1

[PATCH v2 08/15] dt-bindings: display: Convert raspberrypi, 7inch-touchscreen panel to DT schema

[Rob Herring]

Convert the raspberrypi,7inch-touchscreen panel binding to DT schema.

Cc: Eric Anholt <eric@anholt.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../panel/raspberrypi,7inch-touchscreen.txt   | 49 -------------
 .../panel/raspberrypi,7inch-touchscreen.yaml  | 71 +++++++++++++++++++
 2 files changed, 71 insertions(+), 49 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
deleted file mode 100644
index e9e19c059260..000000000000
--- a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt
+++ /dev/null
@@ -1,49 +0,0 @@
-This binding covers the official 7" (800x480) Raspberry Pi touchscreen
-panel.
-
-This DSI panel contains:
-
-- TC358762 DSI->DPI bridge
-- Atmel microcontroller on I2C for power sequencing the DSI bridge and
-  controlling backlight
-- Touchscreen controller on I2C for touch input
-
-and this binding covers the DSI display parts but not its touch input.
-
-Required properties:
-- compatible:	Must be "raspberrypi,7inch-touchscreen-panel"
-- reg:		Must be "45"
-- port:		See panel-common.txt
-
-Example:
-
-dsi1: dsi@7e700000 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	<...>
-
-	port {
-		dsi_out_port: endpoint {
-			remote-endpoint = <&panel_dsi_port>;
-		};
-	};
-};
-
-i2c_dsi: i2c {
-	compatible = "i2c-gpio";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	gpios = <&gpio 28 0
-		 &gpio 29 0>;
-
-	lcd@45 {
-		compatible = "raspberrypi,7inch-touchscreen-panel";
-		reg = <0x45>;
-
-		port {
-			panel_dsi_port: endpoint {
-				remote-endpoint = <&dsi_out_port>;
-			};
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml
new file mode 100644
index 000000000000..22a083f7bc8e
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/raspberrypi,7inch-touchscreen.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: The official 7" (800x480) Raspberry Pi touchscreen
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+description: |+
+  This DSI panel contains:
+
+  - TC358762 DSI->DPI bridge
+  - Atmel microcontroller on I2C for power sequencing the DSI bridge and
+    controlling backlight
+  - Touchscreen controller on I2C for touch input
+
+  and this binding covers the DSI display parts but not its touch input.
+
+properties:
+  compatible:
+    const: raspberrypi,7inch-touchscreen-panel
+
+  reg:
+    const: 0x45
+
+  port: true
+
+required:
+  - compatible
+  - reg
+  - port
+
+additionalProperties: false
+
+examples:
+  - |+
+    dsi1: dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      port {
+        dsi_out_port: endpoint {
+          remote-endpoint = <&panel_dsi_port>;
+        };
+      };
+    };
+
+    i2c_dsi: i2c {
+      compatible = "i2c-gpio";
+      #address-cells = <1>;
+      #size-cells = <0>;
+      scl-gpios = <&gpio 28 0>;
+      sda-gpios = <&gpio 29 0>;
+
+      lcd@45 {
+        compatible = "raspberrypi,7inch-touchscreen-panel";
+        reg = <0x45>;
+
+        port {
+          panel_dsi_port: endpoint {
+            remote-endpoint = <&dsi_out_port>;
+          };
+        };
+      };
+    };
+
+...
-- 
2.20.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[PATCH v2 09/15] dt-bindings: display: Convert tfc,s9700rtwv43tr-01b panel to DT schema

[Rob Herring]

Convert the tfc,s9700rtwv43tr-01b panel binding to DT schema.

Cc: Heiko Stuebner <heiko.stuebner@bq.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/tfc,s9700rtwv43tr-01b.txt   | 15 ----------
 .../display/panel/tfc,s9700rtwv43tr-01b.yaml  | 30 +++++++++++++++++++
 2 files changed, 30 insertions(+), 15 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
deleted file mode 100644
index dfb572f085eb..000000000000
--- a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
+++ /dev/null
@@ -1,15 +0,0 @@
-TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with
-resistive touch
-
-The panel is found on TI AM335x-evm.
-
-Required properties:
-- compatible: should be "tfc,s9700rtwv43tr-01b"
-- power-supply: See panel-common.txt
-
-Optional properties:
-- enable-gpios: GPIO pin to enable or disable the panel, if there is one
-- backlight: phandle of the backlight device attached to the panel
-
-This binding is compatible with the simple-panel binding, which is specified
-in simple-panel.txt in this directory.
diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
new file mode 100644
index 000000000000..614f4a8d8403
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/tfc,s9700rtwv43tr-01b.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with resistive touch
+
+maintainers:
+  - Jyri Sarha <jsarha@ti.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+description: |+
+  The panel is found on TI AM335x-evm.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: tfc,s9700rtwv43tr-01b
+
+  enable-gpios: true
+  backlight: true
+
+required:
+  - compatible
+  - power-supply
+
+...
-- 
2.20.1

[PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Rob Herring]

Convert the tpo,tpg110 panel binding to DT schema.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../bindings/display/panel/tpo,tpg110.txt     |  70 ------------
 .../bindings/display/panel/tpo,tpg110.yaml    | 101 ++++++++++++++++++
 2 files changed, 101 insertions(+), 70 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt
deleted file mode 100644
index 40f3d7c713bb..000000000000
--- a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-TPO TPG110 Panel
-================
-
-This panel driver is a component that acts as an intermediary
-between an RGB output and a variety of panels. The panel
-driver is strapped up in electronics to the desired resolution
-and other properties, and has a control interface over 3WIRE
-SPI. By talking to the TPG110 over SPI, the strapped properties
-can be discovered and the hardware is therefore mostly
-self-describing.
-
-       +--------+
-SPI -> |  TPO   | -> physical display
-RGB -> | TPG110 |
-       +--------+
-
-If some electrical strap or alternate resolution is desired,
-this can be set up by taking software control of the display
-over the SPI interface. The interface can also adjust
-for properties of the display such as gamma correction and
-certain electrical driving levels.
-
-The TPG110 does not know the physical dimensions of the panel
-connected, so this needs to be specified in the device tree.
-
-It requires a GPIO line for control of its reset line.
-
-The serial protocol has line names that resemble I2C but the
-protocol is not I2C but 3WIRE SPI.
-
-Required properties:
-- compatible : one of:
-  "ste,nomadik-nhk15-display", "tpo,tpg110"
-  "tpo,tpg110"
-- grestb-gpios : panel reset GPIO
-- width-mm : see display/panel/panel-common.txt
-- height-mm : see display/panel/panel-common.txt
-
-The device needs to be a child of an SPI bus, see
-spi/spi-bus.txt. The SPI child must set the following
-properties:
-- spi-3wire
-- spi-max-frequency = <3000000>;
-as these are characteristics of this device.
-
-The device node can contain one 'port' child node with one child
-'endpoint' node, according to the bindings defined in
-media/video-interfaces.txt. This node should describe panel's video bus.
-
-Example
--------
-
-panel: display@0 {
-	compatible = "tpo,tpg110";
-	reg = <0>;
-	spi-3wire;
-	/* 320 ns min period ~= 3 MHz */
-	spi-max-frequency = <3000000>;
-	/* Width and height from data sheet */
-	width-mm = <116>;
-	height-mm = <87>;
-	grestb-gpios = <&foo_gpio 5 GPIO_ACTIVE_LOW>;
-	backlight = <&bl>;
-
-	port {
-		nomadik_clcd_panel: endpoint {
-			remote-endpoint = <&foo>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml
new file mode 100644
index 000000000000..a51660b73f28
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/tpo,tpg110.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/tpo,tpg110.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TPO TPG110 Panel
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+description: |+
+  This panel driver is a component that acts as an intermediary
+  between an RGB output and a variety of panels. The panel
+  driver is strapped up in electronics to the desired resolution
+  and other properties, and has a control interface over 3WIRE
+  SPI. By talking to the TPG110 over SPI, the strapped properties
+  can be discovered and the hardware is therefore mostly
+  self-describing.
+
+         +--------+
+  SPI -> |  TPO   | -> physical display
+  RGB -> | TPG110 |
+         +--------+
+
+  If some electrical strap or alternate resolution is desired,
+  this can be set up by taking software control of the display
+  over the SPI interface. The interface can also adjust
+  for properties of the display such as gamma correction and
+  certain electrical driving levels.
+
+  The TPG110 does not know the physical dimensions of the panel
+  connected, so this needs to be specified in the device tree.
+
+  It requires a GPIO line for control of its reset line.
+
+  The serial protocol has line names that resemble I2C but the
+  protocol is not I2C but 3WIRE SPI.
+
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - ste,nomadik-nhk15-display
+          - const: tpo,tpg110
+      - const: tpo,tpg110
+
+  reg: true
+
+  grestb-gpios:
+    maxItems: 1
+    description: panel reset GPIO
+
+  spi-3wire: true
+
+  spi-max-frequency:
+    const: 3000000
+
+required:
+  - compatible
+  - reg
+  - grestb-gpios
+  - width-mm
+  - height-mm
+  - spi-3wire
+  - spi-max-frequency
+  - port
+
+examples:
+  - |+
+    spi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      panel: display@0 {
+        compatible = "tpo,tpg110";
+        reg = <0>;
+        spi-3wire;
+        /* 320 ns min period ~= 3 MHz */
+        spi-max-frequency = <3000000>;
+        /* Width and height from data sheet */
+        width-mm = <116>;
+        height-mm = <87>;
+        grestb-gpios = <&foo_gpio 5 1>;
+        backlight = <&bl>;
+
+        port {
+          nomadik_clcd_panel: endpoint {
+            remote-endpoint = <&foo>;
+          };
+        };
+      };
+    };
+
+...
-- 
2.20.1

[PATCH v2 11/15] dt-bindings: display: Convert panel-lvds to DT schema

[Rob Herring]

Convert the panel-lvds binding to use DT schema. The panel-lvds schema
inherits from the panel-common.yaml schema and specific LVDS panel
bindings should inherit from this schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../bindings/display/panel/lvds.yaml          | 107 ++++++++++++++++
 .../bindings/display/panel/panel-lvds.txt     | 121 ------------------
 2 files changed, 107 insertions(+), 121 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/panel/lvds.yaml
 delete mode 100644 Documentation/devicetree/bindings/display/panel/panel-lvds.txt

diff --git a/Documentation/devicetree/bindings/display/panel/lvds.yaml b/Documentation/devicetree/bindings/display/panel/lvds.yaml
new file mode 100644
index 000000000000..d0083301acbe
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/lvds.yaml
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/lvds.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LVDS Display Panel
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+description: |+
+  LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple
+  incompatible data link layers have been used over time to transmit image data
+  to LVDS panels. This bindings supports display panels compatible with the
+  following specifications.
+
+  [JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February
+  1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA)
+  [LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National
+  Semiconductor
+  [VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video
+  Electronics Standards Association (VESA)
+
+  Device compatible with those specifications have been marketed under the
+  FPD-Link and FlatLink brands.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    contains:
+      const: panel-lvds
+    description:
+      Shall contain "panel-lvds" in addition to a mandatory panel-specific
+      compatible string defined in individual panel bindings. The "panel-lvds"
+      value shall never be used on its own.
+
+  data-mapping:
+    enum:
+      - jeida-18
+      - jeida-24
+      - vesa-24
+    description: |
+      The color signals mapping order.
+
+      LVDS data mappings are defined as follows.
+
+      - "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and
+        [VESA] specifications. Data are transferred as follows on 3 LVDS lanes.
+
+      Slot	    0       1       2       3       4       5       6
+            ________________                         _________________
+      Clock	                \_______________________/
+              ______  ______  ______  ______  ______  ______  ______
+      DATA0	><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
+      DATA1	><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
+      DATA2	><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
+
+      - "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI]
+        specifications. Data are transferred as follows on 4 LVDS lanes.
+
+      Slot	    0       1       2       3       4       5       6
+            ________________                         _________________
+      Clock	                \_______________________/
+              ______  ______  ______  ______  ______  ______  ______
+      DATA0	><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__><
+      DATA1	><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__><
+      DATA2	><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__><
+      DATA3	><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__><
+
+      - "vesa-24" - 24-bit data mapping compatible with the [VESA] specification.
+        Data are transferred as follows on 4 LVDS lanes.
+
+      Slot	    0       1       2       3       4       5       6
+            ________________                         _________________
+      Clock	                \_______________________/
+              ______  ______  ______  ______  ______  ______  ______
+      DATA0	><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
+      DATA1	><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
+      DATA2	><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
+      DATA3	><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__><
+
+      Control signals are mapped as follows.
+
+      CTL0: HSync
+      CTL1: VSync
+      CTL2: Data Enable
+      CTL3: 0
+
+  data-mirror:
+    type: boolean
+    description:
+      If set, reverse the bit order described in the data mappings below on all
+      data lanes, transmitting bits for slots 6 to 0 instead of 0 to 6.
+
+required:
+  - compatible
+  - data-mapping
+  - width-mm
+  - height-mm
+  - panel-timing
+  - port
+
+...
diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
deleted file mode 100644
index 250850a2150b..000000000000
--- a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
+++ /dev/null
@@ -1,121 +0,0 @@
-LVDS Display Panel
-==================
-
-LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple
-incompatible data link layers have been used over time to transmit image data
-to LVDS panels. This bindings supports display panels compatible with the
-following specifications.
-
-[JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February
-1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA)
-[LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National
-Semiconductor
-[VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video
-Electronics Standards Association (VESA)
-
-Device compatible with those specifications have been marketed under the
-FPD-Link and FlatLink brands.
-
-
-Required properties:
-
-- compatible: Shall contain "panel-lvds" in addition to a mandatory
-  panel-specific compatible string defined in individual panel bindings. The
-  "panel-lvds" value shall never be used on its own.
-- width-mm: See panel-common.txt.
-- height-mm: See panel-common.txt.
-- data-mapping: The color signals mapping order, "jeida-18", "jeida-24"
-  or "vesa-24".
-
-Optional properties:
-
-- label: See panel-common.txt.
-- gpios: See panel-common.txt.
-- backlight: See panel-common.txt.
-- power-supply: See panel-common.txt.
-- data-mirror: If set, reverse the bit order described in the data mappings
-  below on all data lanes, transmitting bits for slots 6 to 0 instead of
-  0 to 6.
-
-Required nodes:
-
-- panel-timing: See panel-common.txt.
-- ports: See panel-common.txt. These bindings require a single port subnode
-  corresponding to the panel LVDS input.
-
-
-LVDS data mappings are defined as follows.
-
-- "jeida-18" - 18-bit data mapping compatible with the [JEIDA], [LDI] and
-  [VESA] specifications. Data are transferred as follows on 3 LVDS lanes.
-
-Slot	    0       1       2       3       4       5       6
-	________________                         _________________
-Clock	                \_______________________/
-	  ______  ______  ______  ______  ______  ______  ______
-DATA0	><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
-DATA1	><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
-DATA2	><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
-
-- "jeida-24" - 24-bit data mapping compatible with the [DSIM] and [LDI]
-  specifications. Data are transferred as follows on 4 LVDS lanes.
-
-Slot	    0       1       2       3       4       5       6
-	________________                         _________________
-Clock	                \_______________________/
-	  ______  ______  ______  ______  ______  ______  ______
-DATA0	><__G2__><__R7__><__R6__><__R5__><__R4__><__R3__><__R2__><
-DATA1	><__B3__><__B2__><__G7__><__G6__><__G5__><__G4__><__G3__><
-DATA2	><_CTL2_><_CTL1_><_CTL0_><__B7__><__B6__><__B5__><__B4__><
-DATA3	><_CTL3_><__B1__><__B0__><__G1__><__G0__><__R1__><__R0__><
-
-- "vesa-24" - 24-bit data mapping compatible with the [VESA] specification.
-  Data are transferred as follows on 4 LVDS lanes.
-
-Slot	    0       1       2       3       4       5       6
-	________________                         _________________
-Clock	                \_______________________/
-	  ______  ______  ______  ______  ______  ______  ______
-DATA0	><__G0__><__R5__><__R4__><__R3__><__R2__><__R1__><__R0__><
-DATA1	><__B1__><__B0__><__G5__><__G4__><__G3__><__G2__><__G1__><
-DATA2	><_CTL2_><_CTL1_><_CTL0_><__B5__><__B4__><__B3__><__B2__><
-DATA3	><_CTL3_><__B7__><__B6__><__G7__><__G6__><__R7__><__R6__><
-
-Control signals are mapped as follows.
-
-CTL0: HSync
-CTL1: VSync
-CTL2: Data Enable
-CTL3: 0
-
-
-Example
--------
-
-panel {
-	compatible = "mitsubishi,aa121td01", "panel-lvds";
-
-	width-mm = <261>;
-	height-mm = <163>;
-
-	data-mapping = "jeida-24";
-
-	panel-timing {
-		/* 1280x800 @60Hz */
-		clock-frequency = <71000000>;
-		hactive = <1280>;
-		vactive = <800>;
-		hsync-len = <70>;
-		hfront-porch = <20>;
-		hback-porch = <70>;
-		vsync-len = <5>;
-		vfront-porch = <3>;
-		vback-porch = <15>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};
-- 
2.20.1

[PATCH v2 12/15] dt-bindings: display: Convert innolux,ee101ia-01 panel to DT schema

[Rob Herring]

Convert the innolux,ee101ia-01 LVDS panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/innolux,ee101ia-01d.txt     |  7 ------
 .../display/panel/innolux,ee101ia-01d.yaml    | 22 +++++++++++++++++++
 2 files changed, 22 insertions(+), 7 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt
deleted file mode 100644
index e5ca4ccd55ed..000000000000
--- a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.txt
+++ /dev/null
@@ -1,7 +0,0 @@
-Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel
-
-Required properties:
-- compatible: should be "innolux,ee101ia-01d"
-
-This binding is compatible with the lvds-panel binding, which is specified
-in panel-lvds.txt in this directory.
diff --git a/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml
new file mode 100644
index 000000000000..5cc97cbe17fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/innolux,ee101ia-01d.yaml
@@ -0,0 +1,22 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/innolux,ee101ia-01d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Innolux Corporation 10.1" EE101IA-01D WXGA (1280x800) LVDS panel
+
+maintainers:
+  - Heiko Stuebner <heiko.stuebner@bq.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: lvds.yaml#
+
+properties:
+  compatible:
+    items:
+      - const: innolux,ee101ia-01d
+      - {} # panel-lvds, but not listed here to avoid false select
+
+...
-- 
2.20.1

[PATCH v2 13/15] dt-bindings: display: Convert mitsubishi,aa104xd12 panel to DT schema

[Rob Herring]

Convert the mitsubishi,aa104xd12 LVDS panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/mitsubishi,aa104xd12.txt    | 47 ------------
 .../display/panel/mitsubishi,aa104xd12.yaml   | 71 +++++++++++++++++++
 2 files changed, 71 insertions(+), 47 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt
deleted file mode 100644
index ced0121aed7d..000000000000
--- a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.txt
+++ /dev/null
@@ -1,47 +0,0 @@
-Mitsubishi AA204XD12 LVDS Display Panel
-=======================================
-
-The AA104XD12 is a 10.4" XGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-
-Required properties:
-
-- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that
-  order.
-- vcc-supply: Reference to the regulator powering the panel VCC pins.
-
-
-Example
--------
-
-panel {
-	compatible = "mitsubishi,aa104xd12", "panel-lvds";
-	vcc-supply = <&vcc_3v3>;
-
-	width-mm = <210>;
-	height-mm = <158>;
-
-	data-mapping = "jeida-24";
-
-	panel-timing {
-		/* 1024x768 @65Hz */
-		clock-frequency = <65000000>;
-		hactive = <1024>;
-		vactive = <768>;
-		hsync-len = <136>;
-		hfront-porch = <20>;
-		hback-porch = <160>;
-		vfront-porch = <3>;
-		vback-porch = <29>;
-		vsync-len = <6>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml
new file mode 100644
index 000000000000..fd97ca49c104
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa104xd12.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/mitsubishi,aa104xd12.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mitsubishi AA104XD12 10.4" XGA LVDS Display Panel
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: lvds.yaml#
+
+properties:
+  compatible:
+    items:
+      - const: mitsubishi,aa104xd12
+      - {} # panel-lvds, but not listed here to avoid false select
+
+  vcc-supply:
+    description: Reference to the regulator powering the panel VCC pins.
+
+  data-mapping:
+    const: jeida-24
+
+  width-mm:
+    const: 210
+
+  height-mm:
+    const: 158
+
+
+required:
+  - compatible
+  - vcc-supply
+
+examples:
+  - |+
+
+    panel {
+      compatible = "mitsubishi,aa104xd12", "panel-lvds";
+      vcc-supply = <&vcc_3v3>;
+
+      width-mm = <210>;
+      height-mm = <158>;
+
+      data-mapping = "jeida-24";
+
+      panel-timing {
+        /* 1024x768 @65Hz */
+        clock-frequency = <65000000>;
+        hactive = <1024>;
+        vactive = <768>;
+        hsync-len = <136>;
+        hfront-porch = <20>;
+        hback-porch = <160>;
+        vfront-porch = <3>;
+        vback-porch = <29>;
+        vsync-len = <6>;
+      };
+
+      port {
+        panel_in: endpoint {
+          remote-endpoint = <&lvds_encoder>;
+        };
+      };
+    };
+
+...
-- 
2.20.1

[PATCH v2 14/15] dt-bindings: display: Convert mitsubishi,aa121td01 panel to DT schema

[Rob Herring]

Convert the mitsubishi,aa121td01 LVDS panel binding to DT schema.

Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/mitsubishi,aa121td01.txt    | 47 -------------
 .../display/panel/mitsubishi,aa121td01.yaml   | 69 +++++++++++++++++++
 2 files changed, 69 insertions(+), 47 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt
deleted file mode 100644
index d6e1097504fe..000000000000
--- a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.txt
+++ /dev/null
@@ -1,47 +0,0 @@
-Mitsubishi AA121TD01 LVDS Display Panel
-=======================================
-
-The AA121TD01 is a 12.1" WXGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-
-Required properties:
-
-- compatible: Shall contain "mitsubishi,aa121td01" and "panel-lvds", in that
-  order.
-- vcc-supply: Reference to the regulator powering the panel VCC pins.
-
-
-Example
--------
-
-panel {
-	compatible = "mitsubishi,aa121td01", "panel-lvds";
-	vcc-supply = <&vcc_3v3>;
-
-	width-mm = <261>;
-	height-mm = <163>;
-
-	data-mapping = "jeida-24";
-
-	panel-timing {
-		/* 1280x800 @60Hz */
-		clock-frequency = <71000000>;
-		hactive = <1280>;
-		vactive = <800>;
-		hsync-len = <70>;
-		hfront-porch = <20>;
-		hback-porch = <70>;
-		vsync-len = <5>;
-		vfront-porch = <3>;
-		vback-porch = <15>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml
new file mode 100644
index 000000000000..68750d8f0aef
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/mitsubishi,aa121td01.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/mitsubishi,aa121td01.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mitsubishi AA121TD01 12.1" WXGA LVDS Display Panel
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: lvds.yaml#
+
+properties:
+  compatible:
+    items:
+      - const: mitsubishi,aa121td01
+      - {} # panel-lvds, but not listed here to avoid false select
+
+  vcc-supply:
+    description: Reference to the regulator powering the panel VCC pins.
+
+  data-mapping:
+    const: jeida-24
+
+  width-mm:
+    const: 261
+
+  height-mm:
+    const: 163
+
+required:
+  - compatible
+  - vcc-supply
+
+examples:
+  - |+
+    panel {
+      compatible = "mitsubishi,aa121td01", "panel-lvds";
+      vcc-supply = <&vcc_3v3>;
+
+      width-mm = <261>;
+      height-mm = <163>;
+
+      data-mapping = "jeida-24";
+
+      panel-timing {
+        /* 1280x800 @60Hz */
+        clock-frequency = <71000000>;
+        hactive = <1280>;
+        vactive = <800>;
+        hsync-len = <70>;
+        hfront-porch = <20>;
+        hback-porch = <70>;
+        vsync-len = <5>;
+        vfront-porch = <3>;
+        vback-porch = <15>;
+      };
+
+      port {
+        panel_in: endpoint {
+          remote-endpoint = <&lvds_encoder>;
+        };
+      };
+    };
+
+...
-- 
2.20.1

[PATCH v2 15/15] dt-bindings: display: Convert sgd,gktw70sdae4se panel to DT schema

[Rob Herring]

Convert the sgd,gktw70sdae4se LVDS panel binding to DT schema.

Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/sgd,gktw70sdae4se.txt       | 41 ------------
 .../display/panel/sgd,gktw70sdae4se.yaml      | 63 +++++++++++++++++++
 2 files changed, 63 insertions(+), 41 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
deleted file mode 100644
index d06644b555bd..000000000000
--- a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel
-==========================================================
-
-The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-Required properties:
-
-- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order.
-
-Example
--------
-
-panel {
-	compatible = "sgd,gktw70sdae4se", "panel-lvds";
-
-	width-mm = <153>;
-	height-mm = <86>;
-
-	data-mapping = "jeida-18";
-
-	panel-timing {
-		clock-frequency = <32000000>;
-		hactive = <800>;
-		vactive = <480>;
-		hback-porch = <39>;
-		hfront-porch = <39>;
-		vback-porch = <29>;
-		vfront-porch = <13>;
-		hsync-len = <47>;
-		vsync-len = <2>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml
new file mode 100644
index 000000000000..487283288cb0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/sgd,gktw70sdae4se.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Solomon Goldentek Display GKTW70SDAE4SE 7" WVGA LVDS Display Panel
+
+maintainers:
+  - Neil Armstrong <narmstrong@baylibre.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: lvds.yaml#
+
+properties:
+  compatible:
+    items:
+      - const: sgd,gktw70sdae4se
+      - {} # panel-lvds, but not listed here to avoid false select
+
+  data-mapping:
+    const: jeida-18
+
+  width-mm:
+    const: 153
+
+  height-mm:
+    const: 86
+
+required:
+  - compatible
+
+examples:
+  - |+
+    panel {
+      compatible = "sgd,gktw70sdae4se", "panel-lvds";
+
+      width-mm = <153>;
+      height-mm = <86>;
+
+      data-mapping = "jeida-18";
+
+      panel-timing {
+        clock-frequency = <32000000>;
+        hactive = <800>;
+        vactive = <480>;
+        hback-porch = <39>;
+        hfront-porch = <39>;
+        vback-porch = <29>;
+        vfront-porch = <13>;
+        hsync-len = <47>;
+        vsync-len = <2>;
+      };
+
+      port {
+        panel_in: endpoint {
+          remote-endpoint = <&lvds_encoder>;
+        };
+      };
+    };
+
+...
-- 
2.20.1

[PATCH v2 15/15] dt-bindings: display: Convert sgd, gktw70sdae4se panel to DT schema

[Rob Herring]

Convert the sgd,gktw70sdae4se LVDS panel binding to DT schema.

Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../display/panel/sgd,gktw70sdae4se.txt       | 41 ------------
 .../display/panel/sgd,gktw70sdae4se.yaml      | 63 +++++++++++++++++++
 2 files changed, 63 insertions(+), 41 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
 create mode 100644 Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
deleted file mode 100644
index d06644b555bd..000000000000
--- a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.txt
+++ /dev/null
@@ -1,41 +0,0 @@
-Solomon Goldentek Display GKTW70SDAE4SE LVDS Display Panel
-==========================================================
-
-The GKTW70SDAE4SE is a 7" WVGA TFT-LCD display panel.
-
-These DT bindings follow the LVDS panel bindings defined in panel-lvds.txt
-with the following device-specific properties.
-
-Required properties:
-
-- compatible: Shall contain "sgd,gktw70sdae4se" and "panel-lvds", in that order.
-
-Example
--------
-
-panel {
-	compatible = "sgd,gktw70sdae4se", "panel-lvds";
-
-	width-mm = <153>;
-	height-mm = <86>;
-
-	data-mapping = "jeida-18";
-
-	panel-timing {
-		clock-frequency = <32000000>;
-		hactive = <800>;
-		vactive = <480>;
-		hback-porch = <39>;
-		hfront-porch = <39>;
-		vback-porch = <29>;
-		vfront-porch = <13>;
-		hsync-len = <47>;
-		vsync-len = <2>;
-	};
-
-	port {
-		panel_in: endpoint {
-			remote-endpoint = <&lvds_encoder>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml
new file mode 100644
index 000000000000..487283288cb0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/sgd,gktw70sdae4se.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/sgd,gktw70sdae4se.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Solomon Goldentek Display GKTW70SDAE4SE 7" WVGA LVDS Display Panel
+
+maintainers:
+  - Neil Armstrong <narmstrong@baylibre.com>
+  - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+  - $ref: lvds.yaml#
+
+properties:
+  compatible:
+    items:
+      - const: sgd,gktw70sdae4se
+      - {} # panel-lvds, but not listed here to avoid false select
+
+  data-mapping:
+    const: jeida-18
+
+  width-mm:
+    const: 153
+
+  height-mm:
+    const: 86
+
+required:
+  - compatible
+
+examples:
+  - |+
+    panel {
+      compatible = "sgd,gktw70sdae4se", "panel-lvds";
+
+      width-mm = <153>;
+      height-mm = <86>;
+
+      data-mapping = "jeida-18";
+
+      panel-timing {
+        clock-frequency = <32000000>;
+        hactive = <800>;
+        vactive = <480>;
+        hback-porch = <39>;
+        hfront-porch = <39>;
+        vback-porch = <29>;
+        vfront-porch = <13>;
+        hsync-len = <47>;
+        vsync-len = <2>;
+      };
+
+      port {
+        panel_in: endpoint {
+          remote-endpoint = <&lvds_encoder>;
+        };
+      };
+    };
+
+...
-- 
2.20.1

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Linus Walleij]

On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:

> Convert the tpo,tpg110 panel binding to DT schema.
>
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Awesome, fixed up the MAINATINERS entry and applied and
pushed for DRM next with my Reviewed-by.

Yours,
Linus Walleij

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Linus Walleij]

On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:

> Convert the tpo,tpg110 panel binding to DT schema.
>
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Awesome, fixed up the MAINATINERS entry and applied and
pushed for DRM next with my Reviewed-by.

Yours,
Linus Walleij
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Rob Herring]

On Mon, Jun 24, 2019 at 4:13 PM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:
>
> > Convert the tpo,tpg110 panel binding to DT schema.
> >
> > Cc: Linus Walleij <linus.walleij@linaro.org>
> > Cc: Thierry Reding <thierry.reding@gmail.com>
> > Cc: Sam Ravnborg <sam@ravnborg.org>
> > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Cc: dri-devel@lists.freedesktop.org
> > Signed-off-by: Rob Herring <robh@kernel.org>
>
> Awesome, fixed up the MAINATINERS entry and applied and
> pushed for DRM next with my Reviewed-by.

You shouldn't have because this is dependent on patch 2 and
panel-common.yaml. So now 'make dt_binding_check' is broken.

Rob

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Rob Herring]

On Mon, Jun 24, 2019 at 4:13 PM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:
>
> > Convert the tpo,tpg110 panel binding to DT schema.
> >
> > Cc: Linus Walleij <linus.walleij@linaro.org>
> > Cc: Thierry Reding <thierry.reding@gmail.com>
> > Cc: Sam Ravnborg <sam@ravnborg.org>
> > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Cc: dri-devel@lists.freedesktop.org
> > Signed-off-by: Rob Herring <robh@kernel.org>
>
> Awesome, fixed up the MAINATINERS entry and applied and
> pushed for DRM next with my Reviewed-by.

You shouldn't have because this is dependent on patch 2 and
panel-common.yaml. So now 'make dt_binding_check' is broken.

Rob

Re: [PATCH v2 04/15] dt-bindings: display: Convert armadeus,st0700-adapt panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 554 bytes --]

On Mon, Jun 24, 2019 at 03:56:38PM -0600, Rob Herring wrote:
> Convert the armadeus,st0700-adapt panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 04/15] dt-bindings: display: Convert armadeus,st0700-adapt panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 554 bytes --]

On Mon, Jun 24, 2019 at 03:56:38PM -0600, Rob Herring wrote:
> Convert the armadeus,st0700-adapt panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 05/15] dt-bindings: display: Convert bananapi,s070wv20-ct16 panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 555 bytes --]

On Mon, Jun 24, 2019 at 03:56:39PM -0600, Rob Herring wrote:
> Convert the bananapi,s070wv20-ct16 panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 05/15] dt-bindings: display: Convert bananapi,s070wv20-ct16 panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 555 bytes --]

On Mon, Jun 24, 2019 at 03:56:39PM -0600, Rob Herring wrote:
> Convert the bananapi,s070wv20-ct16 panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 06/15] dt-bindings: display: Convert dlc,dlc0700yzg-1 panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2871 bytes --]

Hi,

On Mon, Jun 24, 2019 at 03:56:40PM -0600, Rob Herring wrote:
> Convert the dlc,dlc0700yzg-1 panel binding to DT schema.
>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>
> ---
>  .../display/panel/dlc,dlc0700yzg-1.txt        | 13 ---------
>  .../display/panel/dlc,dlc0700yzg-1.yaml       | 28 +++++++++++++++++++
>  2 files changed, 28 insertions(+), 13 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
>  create mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> deleted file mode 100644
> index bf06bb025b08..000000000000
> --- a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> -
> -Required properties:
> -- compatible: should be "dlc,dlc0700yzg-1"
> -- power-supply: See simple-panel.txt
> -
> -Optional properties:
> -- reset-gpios: See panel-common.txt
> -- enable-gpios: See simple-panel.txt
> -- backlight: See simple-panel.txt
> -
> -This binding is compatible with the simple-panel binding, which is specified
> -in simple-panel.txt in this directory.
> diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> new file mode 100644
> index 000000000000..1b0b63d46f3e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> @@ -0,0 +1,28 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> +
> +maintainers:
> +  - Philipp Zabel <p.zabel@pengutronix.de>
> +  - Thierry Reding <thierry.reding@gmail.com>
> +
> +allOf:
> +  - $ref: panel-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: dlc,dlc0700yzg-1
> +
> +  reset-gpios: true
> +  enable-gpios: true
> +  backlight: true

Do we need to list them?

Since we don't have additionalItems, it doesn't really change anything
since it will be validated by panel-common.

Either way, it should be consistent between your patches, and the
previous patches in this series didn't list all the properties in the
binding.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 06/15] dt-bindings: display: Convert dlc,dlc0700yzg-1 panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 2871 bytes --]

Hi,

On Mon, Jun 24, 2019 at 03:56:40PM -0600, Rob Herring wrote:
> Convert the dlc,dlc0700yzg-1 panel binding to DT schema.
>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>
> ---
>  .../display/panel/dlc,dlc0700yzg-1.txt        | 13 ---------
>  .../display/panel/dlc,dlc0700yzg-1.yaml       | 28 +++++++++++++++++++
>  2 files changed, 28 insertions(+), 13 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
>  create mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> deleted file mode 100644
> index bf06bb025b08..000000000000
> --- a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> +++ /dev/null
> @@ -1,13 +0,0 @@
> -DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> -
> -Required properties:
> -- compatible: should be "dlc,dlc0700yzg-1"
> -- power-supply: See simple-panel.txt
> -
> -Optional properties:
> -- reset-gpios: See panel-common.txt
> -- enable-gpios: See simple-panel.txt
> -- backlight: See simple-panel.txt
> -
> -This binding is compatible with the simple-panel binding, which is specified
> -in simple-panel.txt in this directory.
> diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> new file mode 100644
> index 000000000000..1b0b63d46f3e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> @@ -0,0 +1,28 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> +
> +maintainers:
> +  - Philipp Zabel <p.zabel@pengutronix.de>
> +  - Thierry Reding <thierry.reding@gmail.com>
> +
> +allOf:
> +  - $ref: panel-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: dlc,dlc0700yzg-1
> +
> +  reset-gpios: true
> +  enable-gpios: true
> +  backlight: true

Do we need to list them?

Since we don't have additionalItems, it doesn't really change anything
since it will be validated by panel-common.

Either way, it should be consistent between your patches, and the
previous patches in this series didn't list all the properties in the
binding.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 07/15] dt-bindings: display: Convert pda,91-00156-a0 panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 548 bytes --]

On Mon, Jun 24, 2019 at 03:56:41PM -0600, Rob Herring wrote:
> Convert the pda,91-00156-a0 panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 07/15] dt-bindings: display: Convert pda,91-00156-a0 panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 548 bytes --]

On Mon, Jun 24, 2019 at 03:56:41PM -0600, Rob Herring wrote:
> Convert the pda,91-00156-a0 panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 08/15] dt-bindings: display: Convert raspberrypi,7inch-touchscreen panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 598 bytes --]

On Mon, Jun 24, 2019 at 03:56:42PM -0600, Rob Herring wrote:
> Convert the raspberrypi,7inch-touchscreen panel binding to DT schema.
>
> Cc: Eric Anholt <eric@anholt.net>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 09/15] dt-bindings: display: Convert tfc,s9700rtwv43tr-01b panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2913 bytes --]

On Mon, Jun 24, 2019 at 03:56:43PM -0600, Rob Herring wrote:
> Convert the tfc,s9700rtwv43tr-01b panel binding to DT schema.
>
> Cc: Heiko Stuebner <heiko.stuebner@bq.com>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>
> ---
>  .../display/panel/tfc,s9700rtwv43tr-01b.txt   | 15 ----------
>  .../display/panel/tfc,s9700rtwv43tr-01b.yaml  | 30 +++++++++++++++++++
>  2 files changed, 30 insertions(+), 15 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
>  create mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
> deleted file mode 100644
> index dfb572f085eb..000000000000
> --- a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
> +++ /dev/null
> @@ -1,15 +0,0 @@
> -TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with
> -resistive touch
> -
> -The panel is found on TI AM335x-evm.
> -
> -Required properties:
> -- compatible: should be "tfc,s9700rtwv43tr-01b"
> -- power-supply: See panel-common.txt
> -
> -Optional properties:
> -- enable-gpios: GPIO pin to enable or disable the panel, if there is one
> -- backlight: phandle of the backlight device attached to the panel
> -
> -This binding is compatible with the simple-panel binding, which is specified
> -in simple-panel.txt in this directory.
> diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
> new file mode 100644
> index 000000000000..614f4a8d8403
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
> @@ -0,0 +1,30 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/panel/tfc,s9700rtwv43tr-01b.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with resistive touch
> +
> +maintainers:
> +  - Jyri Sarha <jsarha@ti.com>
> +  - Thierry Reding <thierry.reding@gmail.com>
> +
> +description: |+
> +  The panel is found on TI AM335x-evm.
> +
> +allOf:
> +  - $ref: panel-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: tfc,s9700rtwv43tr-01b
> +
> +  enable-gpios: true
> +  backlight: true

There's the same remark than on patch 6. Once figured out,
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 09/15] dt-bindings: display: Convert tfc,s9700rtwv43tr-01b panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 2913 bytes --]

On Mon, Jun 24, 2019 at 03:56:43PM -0600, Rob Herring wrote:
> Convert the tfc,s9700rtwv43tr-01b panel binding to DT schema.
>
> Cc: Heiko Stuebner <heiko.stuebner@bq.com>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>
> ---
>  .../display/panel/tfc,s9700rtwv43tr-01b.txt   | 15 ----------
>  .../display/panel/tfc,s9700rtwv43tr-01b.yaml  | 30 +++++++++++++++++++
>  2 files changed, 30 insertions(+), 15 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
>  create mode 100644 Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
>
> diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
> deleted file mode 100644
> index dfb572f085eb..000000000000
> --- a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.txt
> +++ /dev/null
> @@ -1,15 +0,0 @@
> -TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with
> -resistive touch
> -
> -The panel is found on TI AM335x-evm.
> -
> -Required properties:
> -- compatible: should be "tfc,s9700rtwv43tr-01b"
> -- power-supply: See panel-common.txt
> -
> -Optional properties:
> -- enable-gpios: GPIO pin to enable or disable the panel, if there is one
> -- backlight: phandle of the backlight device attached to the panel
> -
> -This binding is compatible with the simple-panel binding, which is specified
> -in simple-panel.txt in this directory.
> diff --git a/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
> new file mode 100644
> index 000000000000..614f4a8d8403
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/tfc,s9700rtwv43tr-01b.yaml
> @@ -0,0 +1,30 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/panel/tfc,s9700rtwv43tr-01b.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TFC S9700RTWV43TR-01B 7" Three Five Corp 800x480 LCD panel with resistive touch
> +
> +maintainers:
> +  - Jyri Sarha <jsarha@ti.com>
> +  - Thierry Reding <thierry.reding@gmail.com>
> +
> +description: |+
> +  The panel is found on TI AM335x-evm.
> +
> +allOf:
> +  - $ref: panel-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: tfc,s9700rtwv43tr-01b
> +
> +  enable-gpios: true
> +  backlight: true

There's the same remark than on patch 6. Once figured out,
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 13/15] dt-bindings: display: Convert mitsubishi,aa104xd12 panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 520 bytes --]

On Mon, Jun 24, 2019 at 03:56:47PM -0600, Rob Herring wrote:
> Convert the mitsubishi,aa104xd12 LVDS panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 13/15] dt-bindings: display: Convert mitsubishi,aa104xd12 panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 520 bytes --]

On Mon, Jun 24, 2019 at 03:56:47PM -0600, Rob Herring wrote:
> Convert the mitsubishi,aa104xd12 LVDS panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 14/15] dt-bindings: display: Convert mitsubishi,aa121td01 panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 520 bytes --]

On Mon, Jun 24, 2019 at 03:56:48PM -0600, Rob Herring wrote:
> Convert the mitsubishi,aa121td01 LVDS panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 14/15] dt-bindings: display: Convert mitsubishi,aa121td01 panel to DT schema

[Maxime Ripard]

[-- Attachment #1.1: Type: text/plain, Size: 520 bytes --]

On Mon, Jun 24, 2019 at 03:56:48PM -0600, Rob Herring wrote:
> Convert the mitsubishi,aa121td01 LVDS panel binding to DT schema.
>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 159 bytes --]

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 15/15] dt-bindings: display: Convert sgd,gktw70sdae4se panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 564 bytes --]

On Mon, Jun 24, 2019 at 03:56:49PM -0600, Rob Herring wrote:
> Convert the sgd,gktw70sdae4se LVDS panel binding to DT schema.
>
> Cc: Neil Armstrong <narmstrong@baylibre.com>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 590 bytes --]

On Mon, Jun 24, 2019 at 03:56:44PM -0600, Rob Herring wrote:
> Convert the tpo,tpg110 panel binding to DT schema.
>
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Cc: Thierry Reding <thierry.reding@gmail.com>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: dri-devel@lists.freedesktop.org
> Signed-off-by: Rob Herring <robh@kernel.org>

Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Linus Walleij]

On Tue, Jun 25, 2019 at 12:47 AM Rob Herring <robh@kernel.org> wrote:
> On Mon, Jun 24, 2019 at 4:13 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> > On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:
> >
> > > Convert the tpo,tpg110 panel binding to DT schema.
> > >
> > > Cc: Linus Walleij <linus.walleij@linaro.org>
> > > Cc: Thierry Reding <thierry.reding@gmail.com>
> > > Cc: Sam Ravnborg <sam@ravnborg.org>
> > > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > > Cc: dri-devel@lists.freedesktop.org
> > > Signed-off-by: Rob Herring <robh@kernel.org>
> >
> > Awesome, fixed up the MAINATINERS entry and applied and
> > pushed for DRM next with my Reviewed-by.
>
> You shouldn't have because this is dependent on patch 2 and
> panel-common.yaml. So now 'make dt_binding_check' is broken.

Ooops easily happens when I am only adressee on this patch and
there is no mention of any dependencies.

Can I simply just merge the panel-common patch as well and we
are all happy?

I can also pick up more panel binding patches, IMO the yaml
conversions are especially uncontroversial and should have low
threshold for merging.

Yours,
Linus Walleij

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Linus Walleij]

On Tue, Jun 25, 2019 at 12:47 AM Rob Herring <robh@kernel.org> wrote:
> On Mon, Jun 24, 2019 at 4:13 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> > On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:
> >
> > > Convert the tpo,tpg110 panel binding to DT schema.
> > >
> > > Cc: Linus Walleij <linus.walleij@linaro.org>
> > > Cc: Thierry Reding <thierry.reding@gmail.com>
> > > Cc: Sam Ravnborg <sam@ravnborg.org>
> > > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > > Cc: dri-devel@lists.freedesktop.org
> > > Signed-off-by: Rob Herring <robh@kernel.org>
> >
> > Awesome, fixed up the MAINATINERS entry and applied and
> > pushed for DRM next with my Reviewed-by.
>
> You shouldn't have because this is dependent on patch 2 and
> panel-common.yaml. So now 'make dt_binding_check' is broken.

Ooops easily happens when I am only adressee on this patch and
there is no mention of any dependencies.

Can I simply just merge the panel-common patch as well and we
are all happy?

I can also pick up more panel binding patches, IMO the yaml
conversions are especially uncontroversial and should have low
threshold for merging.

Yours,
Linus Walleij

Re: [PATCH v2 06/15] dt-bindings: display: Convert dlc,dlc0700yzg-1 panel to DT schema

[Rob Herring]

On Tue, Jun 25, 2019 at 1:55 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> Hi,
>
> On Mon, Jun 24, 2019 at 03:56:40PM -0600, Rob Herring wrote:
> > Convert the dlc,dlc0700yzg-1 panel binding to DT schema.
> >
> > Cc: Philipp Zabel <p.zabel@pengutronix.de>
> > Cc: Thierry Reding <thierry.reding@gmail.com>
> > Cc: Sam Ravnborg <sam@ravnborg.org>
> > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Cc: dri-devel@lists.freedesktop.org
> > Signed-off-by: Rob Herring <robh@kernel.org>
> > ---
> >  .../display/panel/dlc,dlc0700yzg-1.txt        | 13 ---------
> >  .../display/panel/dlc,dlc0700yzg-1.yaml       | 28 +++++++++++++++++++
> >  2 files changed, 28 insertions(+), 13 deletions(-)
> >  delete mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> >  create mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> > deleted file mode 100644
> > index bf06bb025b08..000000000000
> > --- a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> > +++ /dev/null
> > @@ -1,13 +0,0 @@
> > -DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> > -
> > -Required properties:
> > -- compatible: should be "dlc,dlc0700yzg-1"
> > -- power-supply: See simple-panel.txt
> > -
> > -Optional properties:
> > -- reset-gpios: See panel-common.txt
> > -- enable-gpios: See simple-panel.txt
> > -- backlight: See simple-panel.txt
> > -
> > -This binding is compatible with the simple-panel binding, which is specified
> > -in simple-panel.txt in this directory.
> > diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> > new file mode 100644
> > index 000000000000..1b0b63d46f3e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> > @@ -0,0 +1,28 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> > +
> > +maintainers:
> > +  - Philipp Zabel <p.zabel@pengutronix.de>
> > +  - Thierry Reding <thierry.reding@gmail.com>
> > +
> > +allOf:
> > +  - $ref: panel-common.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: dlc,dlc0700yzg-1
> > +
> > +  reset-gpios: true
> > +  enable-gpios: true
> > +  backlight: true
>
> Do we need to list them?
>
> Since we don't have additionalItems, it doesn't really change anything
> since it will be validated by panel-common.

I've gone back and forth on it. I think we need to express what
properties from the common properties apply for a particular panel.
I've been requiring panel bindings to be explicit here rather than
just say "uses the simple-panel binding." For example, if
'power-supply' is not listed, does the panel have a single supply or
multiple supplies that haven't haven't been considered?

> Either way, it should be consistent between your patches, and the
> previous patches in this series didn't list all the properties in the
> binding.

Indeed.

Rob

Re: [PATCH v2 06/15] dt-bindings: display: Convert dlc,dlc0700yzg-1 panel to DT schema

[Rob Herring]

On Tue, Jun 25, 2019 at 1:55 AM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> Hi,
>
> On Mon, Jun 24, 2019 at 03:56:40PM -0600, Rob Herring wrote:
> > Convert the dlc,dlc0700yzg-1 panel binding to DT schema.
> >
> > Cc: Philipp Zabel <p.zabel@pengutronix.de>
> > Cc: Thierry Reding <thierry.reding@gmail.com>
> > Cc: Sam Ravnborg <sam@ravnborg.org>
> > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Cc: dri-devel@lists.freedesktop.org
> > Signed-off-by: Rob Herring <robh@kernel.org>
> > ---
> >  .../display/panel/dlc,dlc0700yzg-1.txt        | 13 ---------
> >  .../display/panel/dlc,dlc0700yzg-1.yaml       | 28 +++++++++++++++++++
> >  2 files changed, 28 insertions(+), 13 deletions(-)
> >  delete mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> >  create mode 100644 Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> > deleted file mode 100644
> > index bf06bb025b08..000000000000
> > --- a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.txt
> > +++ /dev/null
> > @@ -1,13 +0,0 @@
> > -DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> > -
> > -Required properties:
> > -- compatible: should be "dlc,dlc0700yzg-1"
> > -- power-supply: See simple-panel.txt
> > -
> > -Optional properties:
> > -- reset-gpios: See panel-common.txt
> > -- enable-gpios: See simple-panel.txt
> > -- backlight: See simple-panel.txt
> > -
> > -This binding is compatible with the simple-panel binding, which is specified
> > -in simple-panel.txt in this directory.
> > diff --git a/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> > new file mode 100644
> > index 000000000000..1b0b63d46f3e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/panel/dlc,dlc0700yzg-1.yaml
> > @@ -0,0 +1,28 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/panel/dlc,dlc0700yzg-1.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: DLC Display Co. DLC0700YZG-1 7.0" WSVGA TFT LCD panel
> > +
> > +maintainers:
> > +  - Philipp Zabel <p.zabel@pengutronix.de>
> > +  - Thierry Reding <thierry.reding@gmail.com>
> > +
> > +allOf:
> > +  - $ref: panel-common.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: dlc,dlc0700yzg-1
> > +
> > +  reset-gpios: true
> > +  enable-gpios: true
> > +  backlight: true
>
> Do we need to list them?
>
> Since we don't have additionalItems, it doesn't really change anything
> since it will be validated by panel-common.

I've gone back and forth on it. I think we need to express what
properties from the common properties apply for a particular panel.
I've been requiring panel bindings to be explicit here rather than
just say "uses the simple-panel binding." For example, if
'power-supply' is not listed, does the panel have a single supply or
multiple supplies that haven't haven't been considered?

> Either way, it should be consistent between your patches, and the
> previous patches in this series didn't list all the properties in the
> binding.

Indeed.

Rob
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Rob Herring]

On Tue, Jun 25, 2019 at 2:26 AM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Tue, Jun 25, 2019 at 12:47 AM Rob Herring <robh@kernel.org> wrote:
> > On Mon, Jun 24, 2019 at 4:13 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> > > On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:
> > >
> > > > Convert the tpo,tpg110 panel binding to DT schema.
> > > >
> > > > Cc: Linus Walleij <linus.walleij@linaro.org>
> > > > Cc: Thierry Reding <thierry.reding@gmail.com>
> > > > Cc: Sam Ravnborg <sam@ravnborg.org>
> > > > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > > > Cc: dri-devel@lists.freedesktop.org
> > > > Signed-off-by: Rob Herring <robh@kernel.org>
> > >
> > > Awesome, fixed up the MAINATINERS entry and applied and
> > > pushed for DRM next with my Reviewed-by.
> >
> > You shouldn't have because this is dependent on patch 2 and
> > panel-common.yaml. So now 'make dt_binding_check' is broken.
>
> Ooops easily happens when I am only adressee on this patch and
> there is no mention of any dependencies.

It's a series. I would assume the default is 1 person applies a series
unless explicitly stated otherwise.

> Can I simply just merge the panel-common patch as well and we
> are all happy?

I have drm-misc commit rights too, so I'll apply the whole lot when it's ready.

> I can also pick up more panel binding patches, IMO the yaml
> conversions are especially uncontroversial and should have low
> threshold for merging.

Yes, but the threshold is at least 'make dt_binding_check' should not
break. But don't worry, there are 2 other breakages in linux-next
currently.

Rob

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Rob Herring]

On Tue, Jun 25, 2019 at 2:26 AM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Tue, Jun 25, 2019 at 12:47 AM Rob Herring <robh@kernel.org> wrote:
> > On Mon, Jun 24, 2019 at 4:13 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> > > On Mon, Jun 24, 2019 at 11:59 PM Rob Herring <robh@kernel.org> wrote:
> > >
> > > > Convert the tpo,tpg110 panel binding to DT schema.
> > > >
> > > > Cc: Linus Walleij <linus.walleij@linaro.org>
> > > > Cc: Thierry Reding <thierry.reding@gmail.com>
> > > > Cc: Sam Ravnborg <sam@ravnborg.org>
> > > > Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> > > > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > > > Cc: dri-devel@lists.freedesktop.org
> > > > Signed-off-by: Rob Herring <robh@kernel.org>
> > >
> > > Awesome, fixed up the MAINATINERS entry and applied and
> > > pushed for DRM next with my Reviewed-by.
> >
> > You shouldn't have because this is dependent on patch 2 and
> > panel-common.yaml. So now 'make dt_binding_check' is broken.
>
> Ooops easily happens when I am only adressee on this patch and
> there is no mention of any dependencies.

It's a series. I would assume the default is 1 person applies a series
unless explicitly stated otherwise.

> Can I simply just merge the panel-common patch as well and we
> are all happy?

I have drm-misc commit rights too, so I'll apply the whole lot when it's ready.

> I can also pick up more panel binding patches, IMO the yaml
> conversions are especially uncontroversial and should have low
> threshold for merging.

Yes, but the threshold is at least 'make dt_binding_check' should not
break. But don't worry, there are 2 other breakages in linux-next
currently.

Rob

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Linus Walleij]

On Tue, Jun 25, 2019 at 4:26 PM Rob Herring <robh@kernel.org> wrote:
> On Tue, Jun 25, 2019 at 2:26 AM Linus Walleij <linus.walleij@linaro.org> wrote:

> > Can I simply just merge the panel-common patch as well and we
> > are all happy?
>
> I have drm-misc commit rights too, so I'll apply the whole lot when it's ready.
>
> > I can also pick up more panel binding patches, IMO the yaml
> > conversions are especially uncontroversial and should have low
> > threshold for merging.
>
> Yes, but the threshold is at least 'make dt_binding_check' should not
> break. But don't worry, there are 2 other breakages in linux-next
> currently.

OK let's try to live with it for now, if it makes you too much trouble
we can just revert it, accidents happen.

Yours,
Linus Walleij

Re: [PATCH v2 10/15] dt-bindings: display: Convert tpo,tpg110 panel to DT schema

[Linus Walleij]

On Tue, Jun 25, 2019 at 4:26 PM Rob Herring <robh@kernel.org> wrote:
> On Tue, Jun 25, 2019 at 2:26 AM Linus Walleij <linus.walleij@linaro.org> wrote:

> > Can I simply just merge the panel-common patch as well and we
> > are all happy?
>
> I have drm-misc commit rights too, so I'll apply the whole lot when it's ready.
>
> > I can also pick up more panel binding patches, IMO the yaml
> > conversions are especially uncontroversial and should have low
> > threshold for merging.
>
> Yes, but the threshold is at least 'make dt_binding_check' should not
> break. But don't worry, there are 2 other breakages in linux-next
> currently.

OK let's try to live with it for now, if it makes you too much trouble
we can just revert it, accidents happen.

Yours,
Linus Walleij
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [PATCH v2 01/15] dt-bindings: display: rockchip-lvds: Remove panel references

[Heiko Stuebner]

Am Montag, 24. Juni 2019, 23:56:35 CEST schrieb Rob Herring:
> The panel bindings are outside the scope of the Rockchip LVDS interface
> binding. The references are about to change too, so rather than update
> them just drop the section on the panel bindings.
> 
> Cc: Sandy Huang <hjc@rock-chips.com>
> Cc: "Heiko Stübner" <heiko@sntech.de>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: dri-devel@lists.freedesktop.org
> Cc: linux-rockchip@lists.infradead.org
> Signed-off-by: Rob Herring <robh@kernel.org>

applied to drm-misc-next

Thanks
Heiko

Re: [PATCH v2 01/15] dt-bindings: display: rockchip-lvds: Remove panel references

[Heiko Stuebner]

Am Montag, 24. Juni 2019, 23:56:35 CEST schrieb Rob Herring:
> The panel bindings are outside the scope of the Rockchip LVDS interface
> binding. The references are about to change too, so rather than update
> them just drop the section on the panel bindings.
> 
> Cc: Sandy Huang <hjc@rock-chips.com>
> Cc: "Heiko Stübner" <heiko@sntech.de>
> Cc: Maxime Ripard <maxime.ripard@bootlin.com>
> Cc: dri-devel@lists.freedesktop.org
> Cc: linux-rockchip@lists.infradead.org
> Signed-off-by: Rob Herring <robh@kernel.org>

applied to drm-misc-next

Thanks
Heiko


_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel