From: Charles Manning <cdhmanning@gmail.com>
To: openembedded-devel@lists.openembedded.org
Subject: Re: Kernel boot problems
Date: Fri, 29 Jul 2011 16:07:07 +1200 [thread overview]
Message-ID: <CAE21AQruB=Yh9pwVPNM1_nxFohRzBbTqsgt9=tJL-cQDX8EvTw@mail.gmail.com> (raw)
In-Reply-To: <F7C0AA5DD1508F4789E10B6CC9BB75DB04B7A4C0@nzc-ap-xch-02.ap.trimblecorp.net>
> Hi Gary,
>
> Did as you suggested .. no printout from serial_imx_probe() is seen, so
> I guess it isn't been called, will have to trace it back to see why not.
> This is going to be tedious ..
>
> EDIT: However the function imx_serial_init() is being called and
> completes without errors, so I don't know why the probe is not being
> called ..
> Any ideas?
The serial initialisation probably happens twice:
Once for the early console stuff to give to the tracing before the
uncompressing.
Then again for setting up the "real" device tree when the decompressed
kernel is being booted.
I think the probing is only during the second.
>
> Thanks,
> bernie
>
>
> ------------------------------------------------------------------------
> ------------------
> I want to die peacefully in my sleep, like my grandfather, not screaming
> and yelling like the passengers in his car.
>
> -----Original Message-----
> From: Gary Thomas [mailto:gary@mlbassoc.com]
> Sent: Friday, 29 July 2011 10:42 a.m.
> To: Bernard Mentink
> Cc: openembedded-devel@lists.openembedded.org
> Subject: Re: [oe] Kernel boot problems
>
> On 2011-07-28 16:10, Bernard Mentink wrote:
>> Hi Gary,
>>
>> Further down I see a confirmation of the boot params ... i.e
>> console=ttymxc0,115200
>>
>> 8030d600: 73747369 206e6920 656e6f5a 64726f20 ists in Zone ord
>> 8030d610: 202c7265 69626f6d 7974696c 6f726720 er, mobility gro
>> 8030d620: 6e697075 6e6f2067 5420202e 6c61746f uping on. Total
>> 8030d630: 67617020 203a7365 31353233 353c0a32 pages: 32512.<5
>> 8030d640: 72654b3e 206c656e 6d6d6f63 20646e61>Kernel command
>> 8030d650: 656e696c 6f63203a 6c6f736e 74743d65 line: console=tt
>> 8030d660: 63786d79 31312c30 30303235 3e363c0a ymxc0,115200.<6>
>> 8030d670: 20444950 68736168 62617420 6520656c PID hash table e
>> 8030d680: 6972746e 203a7365 20323135 64726f28 ntries: 512 (ord
>> 8030d690: 203a7265 202c312d 38343032 74796220 er: -1, 2048 byt
>> 8030d6a0: 0a297365 443e363c 72746e65 61632079 es).<6>Dentry ca
>> 8030d6b0: 20656863 68736168 62617420 6520656c che hash table e
>> 8030d6c0: 6972746e 203a7365 38333631 6f282034 ntries: 16384 (o
>> 8030d6d0: 72656472 2c34203a 35353620 62203633 rder: 4, 65536 b
>> 8030d6e0: 73657479 363c0a29 6f6e493e 632d6564 ytes).<6>Inode-c
>> 8030d6f0: 65686361 73616820 61742068 20656c62 ache hash table
>>
>> The only mention of serial port is:
>>
>> 8030df00: 20656e69 69676572 72657473 3c0a6465 ine registered.<
>> 8030df10: 6f693e36 68637320 6c756465 63207265 6>io scheduler c
>> 8030df20: 72207166 73696765 65726574 64282064 fq registered (d
>> 8030df30: 75616665 0a29746c 533e363c 61697265 efault).<6>Seria
>> 8030df40: 49203a6c 6420584d 65766972 353c0a72 l: IMX driver.<5
>> 8030df50: 7968703e 70616d73 616c7020 726f6674>physmap platfor
>> 8030df60: 6c66206d 20687361 69766564 203a6563 m flash device:
>> 8030df70: 30303230 30303030 20746120 30303061 02000000 at a000
>> 8030df80: 30303030 3e363c0a 73796870 2d70616d 0000.<6>physmap-
>> 8030df90: 73616c66 3a302e68 756f4620 3120646e flash.0: Found 1
>> 8030dfa0: 36317820 76656420 73656369 20746120 x16 devices at
>> 8030dfb0: 20307830 31206e69 69622d36 61622074 0x0 in 16-bit ba
>> 8030dfc0: 202e6b6e 756e614d 74636166 72657275 nk. Manufacturer
>> 8030dfd0: 20444920 30307830 39383030 69684320 ID 0x000089 Chi
>> 8030dfe0: 44492070 30783020 31393830 353c0a63 p ID 0x00891c.<5
>> 8030dff0: 7075533e 74726f70 726f6620 6d6f6320>Support for com
>>
>> .. And yes I did turn on early debug in the kernel config .. But I
>> don't see any extra messages out the serial port.
>> How can I check that my .config changes have propagated through ok? ..
>
> Do you have CONFIG_SERIAL_IMX_CONSOLE in your config? You can just grep
> for 'SERIAL_IMX_CONSOLE' in .config
>
> You could also edit drivers/serial/imx.c and put some printk() messages
> in serial_imx_probe() to see if it's being called to register your
> device.
> Of course, you'll have to look at the log_buf to read the messages :-)
>
> I notice that your bootargs don't specify a file system. Perhaps if you
> added that the system could actually make it up to multi-user and you
> could log in (serial, SSH, ...)
>
>> ----------------------------------------------------------------------
>> --
>> ------------------
>> I want to die peacefully in my sleep, like my grandfather, not
>> screaming and yelling like the passengers in his car.
>>
>> -----Original Message-----
>> From: Gary Thomas [mailto:gary@mlbassoc.com]
>> Sent: Friday, 29 July 2011 9:40 a.m.
>> To: Bernard Mentink
>> Cc: openembedded-devel@lists.openembedded.org
>> Subject: Re: [oe] Kernel boot problems
>>
>> On 2011-07-28 14:51, Bernard Mentink wrote:
>>> Many thanks for that,
>>>
>>> I had a look through the buffer and I see pretty much normal bootup
>>> text ... It just isn't coming out of the serial port ..
>>>
>>> The only error I saw was the following:
>>> -----------------------------------------
>>> 8030cf80: 00000000 00000001 3a534656 6e614320 ........VFS: Can
>>> 8030cf90: 20746f6e 6e65706f 6f6f7220 65642074 not open root de
>>> 8030cfa0: 65636976 6e282220 296c6c75 726f2022 vice "(null)" or
>>> 8030cfb0: 6b6e7520 6e776f6e 6f6c622d 32286b63 unknown-block(2
>>> 8030cfc0: 64646100 66663d72 66666666 303a6666 .addr=ffffffff:0
>>> 8030cfd0: 69202c31 2d3d7172 000a2931 20393830 1, irq=-1)..089
>>> 8030cfe0: 30373178 20000a29 30307830 63313938 x170).. 0x00891c
>>> 8030cff0: 2030000a 7830202d 65666666 30303030 ..0 - 0xfffe0000
>>> 8030d000: 28202020 36393820 29426b20 2020200a ( 896 kB).
>>> 8030d010: 414d4420 20202020 30203a20 63666678 DMA : 0xffc
>>> 8030d020: 30303030 202d2030 66667830 30303065 00000 - 0xffe000
>>> 8030d030: 20203030 20202820 4d203220 200a2942 00 ( 2 MB).
>>> 8030d040: 76202020 6c6c616d 3a20636f 63783020 vmalloc : 0xc
>>> 8030d050: 30303834 20303030 7830202d 30303466 4800000 - 0xf400
>>> 8030d060: 30303030 28202020 30363720 29424d20 0000 ( 760 MB)
>>> 8030d070: 2020200a 776f6c20 206d656d 30203a20 . lowmem : 0
>>> 8030d080: 30306378 30303030 202d2030 34637830 xc0000000 - 0xc4
>>> 8030d090: 30303030 20203030 20202820 4d203436 000000 ( 64 M
>>> 8030d0a0: 200a2942 6d202020 6c75646f 3a207365 B). modules :
>>> 8030d0b0: 62783020 30303066 20303030 7830202d 0xbf000000 - 0x
>>> 8030d0c0: 30303063 30303030 28202020 36312020 c0000000 ( 16
>>> 8030d0d0: 29424d20 2020200a 2e202020 74696e69 MB). .init
>>> 8030d0e0: 30203a20 30306378 30303830 202d2030 : 0xc0008000 -
>>> 8030d0f0: 30637830 30653130 20203030 20202820 0xc001e000 (
>>> 8030d100: 6b203838 200a2942 20202020 65742e20 88 kB). .te
>>> 8030d110: 3a207478 63783020 65313030 20303030 xt : 0xc001e000
>>> 8030d120: 7830202d 65323063 30303031 28202020 - 0xc02e1000 (
>>> 8030d130: 38323832 29426b20 2020200a 2e202020 2828 kB). .
>>> 8030d140: 61746164 30203a20 32306378 30303666 data : 0xc02f600
>>> 8030d150: 202d2030 30637830 36633033 20203065 0 - 0xc030c6e0
>>> 8030d160: 20202820 6b203039 000a2942 00000000 ( 90 kB)......
>>> --------------------------------------------
>>>
>>> A bit futher down the buffer I saw normal printout ..
>>>
>>> ______________________________________________
>>>
>>> 8030d380: 00000000 00000000 00000000 00000000 ................
>>> 8030d390: 00000000 00000000 00000000 4c3e353c ............<5>L
>>> 8030d3a0: 78756e69 72657620 6e6f6973 362e3220 inux version 2.6
>>> 8030d3b0: 2e36332e 62282031 746e656d 406b6e69 .36.1 (bmentink@
>>> 8030d3c0: 68637241 29786f42 63672820 65762063 ArchBox) (gcc ve
>>> 8030d3d0: 6f697372 2e34206e 20332e35 31313032 rsion 4.5.3 2011
>>> 8030d3e0: 31313330 72702820 6c657265 65736165 0311 (prerelease
>>> 8030d3f0: 47282029 20294343 31232029 45525020 ) (GCC) ) #1 PRE
>>> 8030d400: 54504d45 69724620 6c754a20 20393220 EMPT Fri Jul 29
>>> 8030d410: 303a3830 36313a31 535a4e20 30322054 08:01:16 NZST 20
>>> 8030d420: 3c0a3131 50433e34 41203a55 36764d52 11.<4>CPU: ARMv6
>>> 8030d430: 6d6f632d 69746170 20656c62 636f7270 -compatible proc
>>> 8030d440: 6f737365 345b2072 62373031 5d343633 essor [4107b364]
>>> 8030d450: 76657220 6f697369 2034206e 4d524128 revision 4 (ARM
>>> 8030d460: 45543676 202c294a 303d7263 33356330 v6TEJ), cr=00c53
>>> 8030d470: 0a663738 433e343c 203a5550 54504956 87f.<4>CPU: VIPT
>>> 8030d480: 6e6f6e20 61696c61 676e6973 74616420 nonaliasing dat
>>> 8030d490: 61632061 2c656863 50495620 6f6e2054 a cache, VIPT no
>>> 8030d4a0: 696c616e 6e697361 6e692067 75727473 naliasing instru
>>> 8030d4b0: 6f697463 6163206e 0a656863 4d3e343c ction cache.<4>M
>>> 8030d4c0: 69686361 203a656e 69676f4c 20445063 achine: LogicPD
>>> 8030d4d0: 584d2e69 53203133 3c0a4d4f 654d3e34 i.MX31 SOM.<4>Me
>>> 8030d4e0: 79726f6d 6c6f7020 3a796369 43434520 mory policy: ECC
>>> 8030d4f0: 73696420 656c6261 44202c64 20617461 disabled, Data
>>> 8030d500: 68636163 72772065 62657469 0a6b6361 cache writeback.
>>> 8030d510: 4f3e373c 6f6e206e 30206564 746f7420<7>On node 0 tot
>>> 8030d520: 61706c61 3a736567 33363120 3c0a3438 alpages: 16384.<
>>> 8030d530: 72663e37 615f6565 5f616572 74696e69 7>free_area_init
>>> 8030d540: 646f6e5f 6e203a65 2065646f 70202c30 _node: node 0, p
>>> 8030d550: 74616467 33306320 64306330 6e202c38 gdat c030c0d8, n
>>> 8030d560: 5f65646f 5f6d656d 2070616d 32333063 ode_mem_map c032
>>> 8030d570: 30303031 3e373c0a 6f4e2020 6c616d72 1000.<7> Normal
>>> 8030d580: 6e6f7a20 31203a65 70203832 73656761 zone: 128 pages
>>> 8030d590: 65737520 6f662064 656d2072 70616d6d used for memmap
>>> 8030d5a0: 3e373c0a 6f4e2020 6c616d72 6e6f7a20 .<7> Normal zon
>>> 8030d5b0: 30203a65 67617020 72207365 72657365 e: 0 pages reser
>>> 8030d5c0: 0a646576 203e373c 726f4e20 206c616d ved.<7> Normal
>>> ---------------------------------------------------------------------
>>> -
>>>
>>> I am not sure why it is not printing out the port, my boot param =
>>> "console=ttymxc0,115200"
>>> And the relevent part of conf/machine/mx31ads.conf = SERIAL_CONSOLE =
>
>>> "115200 ttymxc0"
>>>
>>> Any idea's?
>>
>> If you look a bit further you may see some messages about what the
>> serial ports are called, e.g. on my OMAP/3530 I see these messages:
>> omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
>> console [ttyO0] enabled
>> omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
>> omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
>>
>> I don't have an iMX31 available so it's hard to know what they are
>> called.
>>
>> Did you try enabling the early print messages like was suggested? If
>> it works these can be a big help. Your problem is that the kernel is
>> getting started, albeit failing because of no root file system but
>> that's the next step. If the console=XXX selection on the command
>> line is incorrect, there will be no place for the bootup messages to
>> go, hence the silence.
>>
>>
>>> ---------------------------------------------------------------------
>>> -
>>> --
>>> ------------------
>>> I want to die peacefully in my sleep, like my grandfather, not
>>> screaming and yelling like the passengers in his car.
>>>
>>> -----Original Message-----
>>> From: Gary Thomas [mailto:gary@mlbassoc.com]
>>> Sent: Thursday, 28 July 2011 11:22 p.m.
>>> To: openembedded-devel@lists.openembedded.org
>>> Cc: Bernard Mentink
>>> Subject: Re: [oe] Kernel boot problems
>>>
>>> On 2011-07-27 20:20, Bernard Mentink wrote:
>>>>
>>>> Hi Guys,
>>>>
>>>> I have got a bit further with my efforts to boot linux on an imx31
>>>> based platform using u-boot.
>>>>
>>>> My console output is now:
>>>>
>>>> ----------------------------------------------------------------
>>>> uboot> bootm 80100000
>>>> ## Booting kernel from Legacy Image at 80100000 ...
>>>> Image Name: Angstrom/2.6.36/mx31ads
>>>> Created: 2011-07-28 2:03:27 UTC
>>>> Image Type: ARM Linux Kernel Image (uncompressed)
>>>> Data Size: 1586172 Bytes = 1.5 MiB
>>>> Load Address: 8f000000
>>>> Entry Point: 8f000000
>>>> Verifying Checksum ... OK
>>>> Loading Kernel Image ... OK
>>>> OK
>>>>
>>>> Starting kernel ...
>>>>
>>>> Uncompressing Linux... done, booting the kernel.
>>>> -------------------------------------------------------------------
>>>>
>>>> So it seems to be getting to the 1st part of the kernel boot
>>>> process,
>>
>>>> then hangs (I presume the last line comes from kernel code.) I don't
>
>>>> know if the kernel is hanging, or if I don't have any more serial
>>>> out
>>
>>>> ....
>>>> I am passing "console=ttymxc0,115200" to the kernel ..
>>>> Can someone confirm:
>>>> A) If I have the correct Entry point, or does this need to be offset
>
>>>> into the kernel? ..
>>>> B) Is the serial console parameters correct?
>>>> C) What is the correct way to set up the memory map? (my ram starts
>>>> at
>>>
>>>> 0x80000000, ends at 0x8fffffff)
>>>> D) Is there a way to debug initial kernel stuff with serial output?
>>>> In the above, I have decompressed the kernel to the top of the 256M
>>> ram,
>>>> but have only advertised 120M via the bootloader ... for now, not
>>>> knowing what is correct and not wanting the kernel to stomp all over
>
>>>> itself running in ram.
>>>
>>> Analyzing this failure can be hard. If you have some sort of JTAG
>>> setup you might be able to break in at this point, figure out where
>>> it's hanging up, etc.
>>>
>>> Even if you don't have JTAG, there might be some crumbs left around
>>> for you to look at. Linux keeps everything that goes to the
> "console"
>>
>>> in a circular buffer __log_buf[]. Look up that symbol in System.map
>>> (which will be found in your linux build tree). Here's the tricky
>>> part - the map will show a logical address, but U-Boot only knows
>>> physical addresses.
>>> Normally the mapping is pretty easy, e.g. on my OMAP/3530 I might
> see:
>>> $ grep __log_buf linux-2.6.37/System.map
>>> c0527058 b __log_buf
>>> So in U-Boot, I would look at the buffer like this:
>>> U-Boot> md 0x80527058
>>> 80527058: 4c3e353c 78756e69 72657620 6e6f6973<5>Linux version
>>> 80527068: 362e3220 2e37332e 67282033 6d6f6874 2.6.37.3
> (gthom
>>> 80527078: 74407361 6e617469 67282029 76206363 as@titan) (gcc
> v
>>> 80527088: 69737265 34206e6f 312e362e 31303220 ersion 4.6.1
> 201
>>> 80527098: 32363031 70282037 65726572 7361656c 10627
> (prereleas
>>> 805270a8: 28202965 29434347 23202920 72462031 e) (GCC) ) #1
> Fr
>>> 805270b8: 754a2069 3232206c 3a393020 303a3135 i Jul 22
> 09:51:0
>>> ...
>>>
>>> Keep looking through this buffer until it stops with useful
>> characters.
>>> That may tell you where the kernel got hung up and why. If you find
>>> only garbage, it may be more difficult to tell.
>>>
>>> Note: hopefully your board has a RESET button which you can use to
>>> get
>>
>>> back into U-Boot once the kernel boot process hangs. Power cycling
>>> to
>>
>>> reset the board won't work as the contents of RAM will likely be
>>> destroyed.
>>>
>>>
>>> --
>>> ------------------------------------------------------------
>>> Gary Thomas | Consulting for the
>>> MLB Associates | Embedded world
>>> ------------------------------------------------------------
>>
>> --
>> ------------------------------------------------------------
>> Gary Thomas | Consulting for the
>> MLB Associates | Embedded world
>> ------------------------------------------------------------
>
> --
> ------------------------------------------------------------
> Gary Thomas | Consulting for the
> MLB Associates | Embedded world
> ------------------------------------------------------------
>
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
>
> _______________________________________________
> Openembedded-devel mailing list
> Openembedded-devel@lists.openembedded.org
> http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel
>
next prev parent reply other threads:[~2011-07-29 4:11 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-07-28 2:20 Kernel boot problems Bernard Mentink
2011-07-28 11:22 ` Gary Thomas
2011-07-28 12:51 ` Andrea Adami
2011-07-28 20:51 ` Bernard Mentink
2011-07-28 21:39 ` Gary Thomas
2011-07-28 22:10 ` Bernard Mentink
2011-07-28 22:41 ` Gary Thomas
2011-07-28 23:03 ` Bernard Mentink
2011-07-29 1:18 ` Bernard Mentink
2011-07-29 1:41 ` Bernard Mentink
2011-07-29 4:07 ` Charles Manning [this message]
2011-07-31 20:57 ` Bernard Mentink
2011-07-28 15:47 ` Daniel Smith
-- strict thread matches above, loose matches on Subject: below --
2001-01-28 0:14 kernel " Derek Benson
2001-01-28 0:49 ` Andre Hedrick
2001-01-27 20:58 Ryan Hairyes
2001-01-27 21:46 ` Joe deBlaquiere
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAE21AQruB=Yh9pwVPNM1_nxFohRzBbTqsgt9=tJL-cQDX8EvTw@mail.gmail.com' \
--to=cdhmanning@gmail.com \
--cc=openembedded-devel@lists.openembedded.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.