* [0/2] arm64: Initial support for Texas Instruments J721E EAIK
@ 2021-06-02 18:22 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2021-06-02 18:22 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC. This series intoduces the basic support for J721E
EAIK.
Sinthu Raja (2):
dt-bindings: arm: ti: Add bindings for J721E EAIK
arm64: dts: ti: Add support for J721E EAIK
.../devicetree/bindings/arm/ti/k3.yaml | 2 +
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 343 ++++++++++++++++++
3 files changed, 347 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
base-commit: 231bc539066760aaa44d46818c85b14ca2f56d9f
--
2.31.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [0/2] arm64: Initial support for Texas Instruments J721E EAIK
@ 2021-06-02 18:22 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2021-06-02 18:22 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC. This series intoduces the basic support for J721E
EAIK.
Sinthu Raja (2):
dt-bindings: arm: ti: Add bindings for J721E EAIK
arm64: dts: ti: Add support for J721E EAIK
.../devicetree/bindings/arm/ti/k3.yaml | 2 +
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 343 ++++++++++++++++++
3 files changed, 347 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
base-commit: 231bc539066760aaa44d46818c85b14ca2f56d9f
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* [1/2] dt-bindings: arm: ti: Add bindings for J721E EAIK
2021-06-02 18:22 ` Sinthu Raja
@ 2021-06-02 18:22 ` Sinthu Raja
-1 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2021-06-02 18:22 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC.
Add DT binding documentation for J721E EAIK
Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
Documentation/devicetree/bindings/arm/ti/k3.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index c5aa362e4026..923dd7cf1dc6 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -29,6 +29,8 @@ properties:
- description: K3 J721E SoC
items:
+ - enum:
+ - ti,j721e-eaik
- const: ti,j721e
- description: K3 J7200 SoC
--
2.31.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [1/2] dt-bindings: arm: ti: Add bindings for J721E EAIK
@ 2021-06-02 18:22 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2021-06-02 18:22 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC.
Add DT binding documentation for J721E EAIK
Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
Documentation/devicetree/bindings/arm/ti/k3.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index c5aa362e4026..923dd7cf1dc6 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -29,6 +29,8 @@ properties:
- description: K3 J721E SoC
items:
+ - enum:
+ - ti,j721e-eaik
- const: ti,j721e
- description: K3 J7200 SoC
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [2/2] arm64: dts: ti: Add support for J721E EAIK
2021-06-02 18:22 ` Sinthu Raja
@ 2021-06-02 18:22 ` Sinthu Raja
-1 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2021-06-02 18:22 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for perception, sensor
fusion, localization, path planning tasks in robotics, industrial and
automotive applications.
J721E EAIK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 UHS-1 capable µSD card slot
* x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* x4 CAN-FD interface
* x1 DP interface
* x1 HDMI interface
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi compatible GPIO header
* Compact TI 20-Pin connector for JTAG debug
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for J721E-EAIK.
Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 343 +++++++++++++++++++++++
2 files changed, 345 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d56c742f5a10..00eb2077616e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
+
dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
new file mode 100644
index 000000000000..66a9fe19df4f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ compatible = "ti,j721e-eaik", "ti,j721e";
+ model = "Texas Instruments J721E EAIK";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* 4G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+ <0x00000008 0x80000000 0x00000000 0x80000000>;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+ };
+
+ vusb_main: fixedregulator-vusb-main5v0 {
+ /* USB MAIN INPUT 5V DC */
+ compatible = "regulator-fixed";
+ regulator-name = "vusb-main5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: fixedregulator-vsys3v3 {
+ /* Output of LM5141 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vusb_main>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_mmc1_en_pins_default>;
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv_alt: gpio-regulator-tps659411 {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
+ regulator-name = "tps659411";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_3v3>;
+ gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+};
+
+&main_pmx0 {
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
+ J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
+ J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
+ J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+ J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
+ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
+ J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
+ >;
+ };
+
+ main_uart0_pins_default: main-uart0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
+ J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
+ J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
+ J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+ J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+ J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+ >;
+ };
+
+ main_i2c3_pins_default: main-i2c3-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+ J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+ >;
+ };
+};
+
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
+ J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
+ J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
+ J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
+ J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
+ J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
+ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
+ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
+ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
+ J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
+ >;
+ };
+
+ vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
+ >;
+ };
+
+ vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
+ >;
+ };
+
+ wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
+ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
+ >;
+ };
+};
+
+&wkup_uart0 {
+ /* Wakeup UART is used by System firmware */
+ status = "reserved";
+};
+
+&main_uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
+ /* Shared with ATF on this platform */
+ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+};
+
+&main_uart2 {
+ /* Brought out on RPi header */
+ status = "disabled";
+};
+
+&main_uart3 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart5 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart6 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart7 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart8 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart9 {
+ /* Brought out on M.2 E Key */
+ status = "disabled";
+};
+
+&main_sdhci0 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_sdhci1 {
+ /* SD Card */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv_alt>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&main_sdhci2 {
+ /* Unused */
+ status = "disabled";
+};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ u-boot,dm-spl;
+ };
+ };
+};
+
+&ospi1 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+
+ /* PCIe1 M.2 M Key I2C */
+ pcie1_m2_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ /* PCIe0 M.2 E Key I2C */
+ pcie0_m2_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+};
+
+&main_i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c3_pins_default>;
+ clock-frequency = <400000>;
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+
+ /* CAM0 I2C */
+ ti_cam0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ /* CAM1 I2C */
+ rpi_cam0_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&main_i2c4 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_i2c5 {
+ /* Brought out on RPi Header */
+ status = "disabled";
+};
+
+&main_i2c6 {
+ /* Unused */
+ status = "disabled";
+};
+
--
2.31.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [2/2] arm64: dts: ti: Add support for J721E EAIK
@ 2021-06-02 18:22 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2021-06-02 18:22 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Device Tree Mailing List, Linux ARM Mailing List, Lokesh Vutla,
Amarnath MB, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for perception, sensor
fusion, localization, path planning tasks in robotics, industrial and
automotive applications.
J721E EAIK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 UHS-1 capable µSD card slot
* x1 PCIe M.2 E Key with x1 USB2.0, x1 MCASP, x1 MMC, x1 UART
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* x4 CAN-FD interface
* x1 DP interface
* x1 HDMI interface
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi compatible GPIO header
* Compact TI 20-Pin connector for JTAG debug
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for J721E-EAIK.
Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j721e-eaik.dts | 343 +++++++++++++++++++++++
2 files changed, 345 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d56c742f5a10..00eb2077616e 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -12,6 +12,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-eaik.dtb
+
dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
new file mode 100644
index 000000000000..66a9fe19df4f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-eaik.dts
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ compatible = "ti,j721e-eaik", "ti,j721e";
+ model = "Texas Instruments J721E EAIK";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* 4G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+ <0x00000008 0x80000000 0x00000000 0x80000000>;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+ };
+
+ vusb_main: fixedregulator-vusb-main5v0 {
+ /* USB MAIN INPUT 5V DC */
+ compatible = "regulator-fixed";
+ regulator-name = "vusb-main5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: fixedregulator-vsys3v3 {
+ /* Output of LM5141 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vusb_main>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_mmc1_en_pins_default>;
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv_alt: gpio-regulator-tps659411 {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
+ regulator-name = "tps659411";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_3v3>;
+ gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+};
+
+&main_pmx0 {
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
+ J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
+ J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
+ J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+ J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
+ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
+ J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
+ >;
+ };
+
+ main_uart0_pins_default: main-uart0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
+ J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
+ J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
+ J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+ J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+ J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+ >;
+ };
+
+ main_i2c3_pins_default: main-i2c3-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+ J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+ >;
+ };
+};
+
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
+ J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
+ J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
+ J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
+ J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
+ J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
+ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
+ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
+ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
+ J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
+ >;
+ };
+
+ vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
+ >;
+ };
+
+ vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
+ >;
+ };
+
+ wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
+ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
+ >;
+ };
+};
+
+&wkup_uart0 {
+ /* Wakeup UART is used by System firmware */
+ status = "reserved";
+};
+
+&main_uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
+ /* Shared with ATF on this platform */
+ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+};
+
+&main_uart2 {
+ /* Brought out on RPi header */
+ status = "disabled";
+};
+
+&main_uart3 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart5 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart6 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart7 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart8 {
+ /* UART not brought out */
+ status = "disabled";
+};
+
+&main_uart9 {
+ /* Brought out on M.2 E Key */
+ status = "disabled";
+};
+
+&main_sdhci0 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_sdhci1 {
+ /* SD Card */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv_alt>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&main_sdhci2 {
+ /* Unused */
+ status = "disabled";
+};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ u-boot,dm-spl;
+ };
+ };
+};
+
+&ospi1 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ i2c-switch@71 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+
+ /* PCIe1 M.2 M Key I2C */
+ pcie1_m2_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ /* PCIe0 M.2 E Key I2C */
+ pcie0_m2_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&main_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+};
+
+&main_i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c3_pins_default>;
+ clock-frequency = <400000>;
+
+ i2c-switch@70 {
+ compatible = "nxp,pca9543";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+
+ /* CAM0 I2C */
+ ti_cam0_i2c: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ /* CAM1 I2C */
+ rpi_cam0_i2c: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+};
+
+&main_i2c4 {
+ /* Unused */
+ status = "disabled";
+};
+
+&main_i2c5 {
+ /* Brought out on RPi Header */
+ status = "disabled";
+};
+
+&main_i2c6 {
+ /* Unused */
+ status = "disabled";
+};
+
--
2.31.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [1/2] dt-bindings: arm: ti: Add bindings for J721E EAIK
2021-06-02 18:22 ` Sinthu Raja
@ 2021-06-02 20:19 ` Rob Herring
-1 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2021-06-02 20:19 UTC (permalink / raw)
To: Sinthu Raja
Cc: Amarnath MB, Lokesh Vutla, Linux ARM Mailing List, Rob Herring,
Tero Kristo, Sinthu Raja, Device Tree Mailing List,
Nishanth Menon
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 1525 bytes --]
On Wed, 02 Jun 2021 23:52:36 +0530, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> for TI’s J721E SoC.
> Add DT binding documentation for J721E EAIK
>
> Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
> Documentation/devicetree/bindings/arm/ti/k3.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/remoteproc/ti,k3-dsp-rproc.example.dt.yaml: /: compatible: 'oneOf' conditional failed, one must be fixed:
['ti,j721e'] is too short
'ti,j721e' is not one of ['ti,am654-evm', 'siemens,iot2050-basic', 'siemens,iot2050-advanced']
'ti,j721e' is not one of ['ti,j721e-eaik']
'ti,j7200' was expected
'ti,j721e' is not one of ['ti,am642-evm', 'ti,am642-sk']
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/arm/ti/k3.yaml
See https://patchwork.ozlabs.org/patch/1486849
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [1/2] dt-bindings: arm: ti: Add bindings for J721E EAIK
@ 2021-06-02 20:19 ` Rob Herring
0 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2021-06-02 20:19 UTC (permalink / raw)
To: Sinthu Raja
Cc: Amarnath MB, Lokesh Vutla, Linux ARM Mailing List, Rob Herring,
Tero Kristo, Sinthu Raja, Device Tree Mailing List,
Nishanth Menon
[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]
On Wed, 02 Jun 2021 23:52:36 +0530, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> for TI’s J721E SoC.
> Add DT binding documentation for J721E EAIK
>
> Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
> Documentation/devicetree/bindings/arm/ti/k3.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/remoteproc/ti,k3-dsp-rproc.example.dt.yaml: /: compatible: 'oneOf' conditional failed, one must be fixed:
['ti,j721e'] is too short
'ti,j721e' is not one of ['ti,am654-evm', 'siemens,iot2050-basic', 'siemens,iot2050-advanced']
'ti,j721e' is not one of ['ti,j721e-eaik']
'ti,j7200' was expected
'ti,j721e' is not one of ['ti,am642-evm', 'ti,am642-sk']
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/arm/ti/k3.yaml
See https://patchwork.ozlabs.org/patch/1486849
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [1/2] dt-bindings: arm: ti: Add bindings for J721E EAIK
2021-06-02 20:19 ` Rob Herring
@ 2021-06-03 12:24 ` Sinthu Raja M
-1 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja M @ 2021-06-03 12:24 UTC (permalink / raw)
To: Rob Herring
Cc: Amarnath MB, Lokesh Vutla, Linux ARM Mailing List, Rob Herring,
Tero Kristo, Sinthu Raja, Device Tree Mailing List,
Nishanth Menon
On Thu, Jun 3, 2021 at 1:49 AM Rob Herring <robh@kernel.org> wrote:
>
> On Wed, 02 Jun 2021 23:52:36 +0530, Sinthu Raja wrote:
> > From: Sinthu Raja <sinthu.raja@ti.com>
> >
> > J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> > for TI’s J721E SoC.
> > Add DT binding documentation for J721E EAIK
> >
> > Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> > ---
> > Documentation/devicetree/bindings/arm/ti/k3.yaml | 2 ++
> > 1 file changed, 2 insertions(+)
> >
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/remoteproc/ti,k3-dsp-rproc.example.dt.yaml: /: compatible: 'oneOf' conditional failed, one must be fixed:
> ['ti,j721e'] is too short
> 'ti,j721e' is not one of ['ti,am654-evm', 'siemens,iot2050-basic', 'siemens,iot2050-advanced']
> 'ti,j721e' is not one of ['ti,j721e-eaik']
> 'ti,j7200' was expected
> 'ti,j721e' is not one of ['ti,am642-evm', 'ti,am642-sk']
> From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/arm/ti/k3.yaml
>
> See https://linkprotect.cudasvc.com/url?a=https%3a%2f%2fpatchwork.ozlabs.org%2fpatch%2f1486849&c=E,1,iIjO1U6FeYcns7IR90F8V0U--545Y71F5JY6Imzb3PvTuPMht6sg0BpDbx7zvPe6hiInzXD-Jlt9L7harG-5n6pTJTnQ-haZhbukv25Bt-8NVFlY-Xcc9fR68g,,&typo=1
>
> This check can fail if there are any dependencies. The base for a patch
> series is generally the most recent rc1.
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
>
Hi Rob,
Thanks for your comment and valuable inputs. Earlier with the 'make
dt_binding_check', I didn't get the mentioned error. After installing
the yamllint and dt-schema update I am able to see the error(s).
Will fix and resubmit the patches.
Regards
Sinthu Raja
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [1/2] dt-bindings: arm: ti: Add bindings for J721E EAIK
@ 2021-06-03 12:24 ` Sinthu Raja M
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja M @ 2021-06-03 12:24 UTC (permalink / raw)
To: Rob Herring
Cc: Amarnath MB, Lokesh Vutla, Linux ARM Mailing List, Rob Herring,
Tero Kristo, Sinthu Raja, Device Tree Mailing List,
Nishanth Menon
On Thu, Jun 3, 2021 at 1:49 AM Rob Herring <robh@kernel.org> wrote:
>
> On Wed, 02 Jun 2021 23:52:36 +0530, Sinthu Raja wrote:
> > From: Sinthu Raja <sinthu.raja@ti.com>
> >
> > J721E EdgeAI Kit (EAIK) is a low cost, small form factor board designed
> > for TI’s J721E SoC.
> > Add DT binding documentation for J721E EAIK
> >
> > Signed-off-by: Amarnath MB <amarnath.mb@ti.com>
> > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> > ---
> > Documentation/devicetree/bindings/arm/ti/k3.yaml | 2 ++
> > 1 file changed, 2 insertions(+)
> >
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/remoteproc/ti,k3-dsp-rproc.example.dt.yaml: /: compatible: 'oneOf' conditional failed, one must be fixed:
> ['ti,j721e'] is too short
> 'ti,j721e' is not one of ['ti,am654-evm', 'siemens,iot2050-basic', 'siemens,iot2050-advanced']
> 'ti,j721e' is not one of ['ti,j721e-eaik']
> 'ti,j7200' was expected
> 'ti,j721e' is not one of ['ti,am642-evm', 'ti,am642-sk']
> From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/arm/ti/k3.yaml
>
> See https://linkprotect.cudasvc.com/url?a=https%3a%2f%2fpatchwork.ozlabs.org%2fpatch%2f1486849&c=E,1,iIjO1U6FeYcns7IR90F8V0U--545Y71F5JY6Imzb3PvTuPMht6sg0BpDbx7zvPe6hiInzXD-Jlt9L7harG-5n6pTJTnQ-haZhbukv25Bt-8NVFlY-Xcc9fR68g,,&typo=1
>
> This check can fail if there are any dependencies. The base for a patch
> series is generally the most recent rc1.
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
>
Hi Rob,
Thanks for your comment and valuable inputs. Earlier with the 'make
dt_binding_check', I didn't get the mentioned error. After installing
the yamllint and dt-schema update I am able to see the error(s).
Will fix and resubmit the patches.
Regards
Sinthu Raja
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2021-06-03 12:26 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-06-02 18:22 [0/2] arm64: Initial support for Texas Instruments J721E EAIK Sinthu Raja
2021-06-02 18:22 ` Sinthu Raja
2021-06-02 18:22 ` [1/2] dt-bindings: arm: ti: Add bindings for " Sinthu Raja
2021-06-02 18:22 ` Sinthu Raja
2021-06-02 20:19 ` Rob Herring
2021-06-02 20:19 ` Rob Herring
2021-06-03 12:24 ` Sinthu Raja M
2021-06-03 12:24 ` Sinthu Raja M
2021-06-02 18:22 ` [2/2] arm64: dts: ti: Add support " Sinthu Raja
2021-06-02 18:22 ` Sinthu Raja
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.