From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: MIME-Version: 1.0 Sender: daniel.baluta@gmail.com In-Reply-To: <6e2db76ca3688c86a36a5adcca0b89ecf436cebf.1410393352.git.sathyanarayanan.kuppuswamy@linux.intel.com> References: <6e2db76ca3688c86a36a5adcca0b89ecf436cebf.1410393352.git.sathyanarayanan.kuppuswamy@linux.intel.com> Date: Thu, 11 Sep 2014 11:21:20 +0300 Message-ID: Subject: Re: [PATCH v4 1/1] iio: jsa1212: Add JSA1212 proximity/ALS sensor From: Daniel Baluta To: Kuppuswamy Sathyanarayanan Cc: Jonathan Cameron , linux-iio@vger.kernel.org, Srinivas Pandruvada Content-Type: text/plain; charset=UTF-8 List-ID: On Thu, Sep 11, 2014 at 3:09 AM, Kuppuswamy Sathyanarayanan wrote: > This patch adds a new driver for solteam opto JSA1212 proximity and > ambient light sensor. > > Basic details of the chip can be found here. > > http://www.solteamopto.com.tw/detail.php?ms=3&po_unit=2&pt_unit=29&p_unit=120 > > Signed-off-by: Kuppuswamy Sathyanarayanan > Signed-off-by: Srinivas Pandruvada The code looks nice and clean. Few comments inline. Take them with a grain of salt since I'm new around linux-iio. > --- > drivers/iio/light/Kconfig | 10 + > drivers/iio/light/Makefile | 1 + > drivers/iio/light/jsa1212.c | 487 ++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 498 insertions(+) > create mode 100644 drivers/iio/light/jsa1212.c > > diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig > index bf05ca5..b81d8a3 100644 > --- a/drivers/iio/light/Kconfig > +++ b/drivers/iio/light/Kconfig > @@ -99,6 +99,16 @@ config HID_SENSOR_PROX > To compile this driver as a module, choose M here: the > module will be called hid-sensor-prox. > > +config JSA1212 > + tristate "JSA1212 ALS and proximity sensor driver" > + depends on I2C > + help > + Say Y here if you want to build a IIO driver for JSA1212 > + proximity & ALS sensor device. > + > + To compile this driver as a module, choose M here: > + the module will be called jsa1212. > + > config SENSORS_LM3533 > tristate "LM3533 ambient light sensor" > depends on MFD_LM3533 > diff --git a/drivers/iio/light/Makefile b/drivers/iio/light/Makefile > index 8b8c09f..23c6aa9 100644 > --- a/drivers/iio/light/Makefile > +++ b/drivers/iio/light/Makefile > @@ -11,6 +11,7 @@ obj-$(CONFIG_GP2AP020A00F) += gp2ap020a00f.o > obj-$(CONFIG_HID_SENSOR_ALS) += hid-sensor-als.o > obj-$(CONFIG_HID_SENSOR_PROX) += hid-sensor-prox.o > obj-$(CONFIG_ISL29125) += isl29125.o > +obj-$(CONFIG_JSA1212) += jsa1212.o > obj-$(CONFIG_SENSORS_LM3533) += lm3533-als.o > obj-$(CONFIG_LTR501) += ltr501.o > obj-$(CONFIG_SENSORS_TSL2563) += tsl2563.o > diff --git a/drivers/iio/light/jsa1212.c b/drivers/iio/light/jsa1212.c > new file mode 100644 > index 0000000..9974bac > --- /dev/null > +++ b/drivers/iio/light/jsa1212.c > @@ -0,0 +1,487 @@ > +/* > + * JSA1212 Ambient Light & Proximity Sensor Driver > + * > + * Copyright (c) 2014, Intel Corporation. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for > + * more details. > + */ I think some TODO should be added here. I see that device supports interrupts + thresholds but they are not implemented. Also if there is a fix I2C slave address here is the place you should mention about it. > + > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include I don't think you need irq.h and interrupt.h for the moment. > +#include > +#include > +#include > +#include > +#include > +#include > + > +/* JSA1212 reg address */ > +#define JSA1212_CONF_REG 0x01 > +#define JSA1212_INT_REG 0x02 > +#define JSA1212_PXS_LT_REG 0x03 > +#define JSA1212_PXS_HT_REG 0x04 > +#define JSA1212_ALS_TH1_REG 0x05 > +#define JSA1212_ALS_TH2_REG 0x06 > +#define JSA1212_ALS_TH3_REG 0x07 > +#define JSA1212_PXS_DATA_REG 0x08 > +#define JSA1212_ALS_DT1_REG 0x09 > +#define JSA1212_ALS_DT2_REG 0x0A > +#define JSA1212_ALS_RNG_REG 0x0B > +#define JSA1212_MAX_REG 0x0C > + > +/* JSA1212 reg masks */ > +#define JSA1212_CONF_MASK 0xFF > +#define JSA1212_INT_MASK 0xFF > +#define JSA1212_PXS_LT_MASK 0xFF > +#define JSA1212_PXS_HT_MASK 0xFF > +#define JSA1212_ALS_TH1_MASK 0xFF > +#define JSA1212_ALS_TH2_LT_MASK 0x0F > +#define JSA1212_ALS_TH2_HT_MASK 0xF0 > +#define JSA1212_ALS_TH3_MASK 0xFF > +#define JSA1212_PXS_DATA_MASK 0xFF > +#define JSA1212_ALS_DATA_MASK 0xFFF Is this 0xFF or 0x0FFF? How many bits of ALS data you have? > +#define JSA1212_ALS_DT1_MASK 0xFF > +#define JSA1212_ALS_DT2_MASK 0x0F > +#define JSA1212_ALS_RNG_MASK 0x07 > +#define JSA1212_REG_MASK 0xFF > + > +/* JSA1212 CONF REG bits */ > +#define JSA1212_CONF_PXS_MASK 0x80 > +#define JSA1212_CONF_PXS_ENABLE 0x80 > +#define JSA1212_CONF_PXS_DISABLE 0x00 > +#define JSA1212_CONF_ALS_MASK 0x04 > +#define JSA1212_CONF_ALS_ENABLE 0x04 > +#define JSA1212_CONF_ALS_DISABLE 0x00 > +#define JSA1212_CONF_IRDR_MASK 0x08 > +#define JSA1212_CONF_IRDR_ENABLE 0x08 > +#define JSA1212_CONF_IRDR_DISABLE 0x00 > +#define JSA1212_CONF_PXS_SLP_MASK 0x70 > +#define JSA1212_CONF_PXS_SLP_0MS 0x70 > +#define JSA1212_CONF_PXS_SLP_12MS 0x60 > +#define JSA1212_CONF_PXS_SLP_50MS 0x50 > +#define JSA1212_CONF_PXS_SLP_75MS 0x40 > +#define JSA1212_CONF_PXS_SLP_100MS 0x30 > +#define JSA1212_CONF_PXS_SLP_200MS 0x20 > +#define JSA1212_CONF_PXS_SLP_400MS 0x10 > +#define JSA1212_CONF_PXS_SLP_800MS 0x00 > + > +/* JSA1212 INT REG bits */ > +#define JSA1212_INT_CTRL_MASK 0x01 > +#define JSA1212_INT_CTRL_EITHER 0x00 > +#define JSA1212_INT_CTRL_BOTH 0x01 > +#define JSA1212_INT_ALS_PRST_MASK 0x06 > +#define JSA1212_INT_ALS_PRST_1CONV 0x00 > +#define JSA1212_INT_ALS_PRST_4CONV 0x02 > +#define JSA1212_INT_ALS_PRST_8CONV 0x04 > +#define JSA1212_INT_ALS_PRST_16CONV 0x06 > +#define JSA1212_INT_ALS_FLAG_MASK 0x08 > +#define JSA1212_INT_ALS_FLAG_CLR 0x00 > +#define JSA1212_INT_PXS_PRST_MASK 0x60 > +#define JSA1212_INT_PXS_PRST_1CONV 0x00 > +#define JSA1212_INT_PXS_PRST_4CONV 0x20 > +#define JSA1212_INT_PXS_PRST_8CONV 0x40 > +#define JSA1212_INT_PXS_PRST_16CONV 0x60 > +#define JSA1212_INT_PXS_FLAG_MASK 0x80 > +#define JSA1212_INT_PXS_FLAG_CLR 0x00 > + > +/* JSA1212 ALS RNG REG bits */ > +#define JSA1212_ALS_RNG_0_2048 0x00 > +#define JSA1212_ALS_RNG_0_1024 0x01 > +#define JSA1212_ALS_RNG_0_512 0x02 > +#define JSA1212_ALS_RNG_0_256 0x03 > +#define JSA1212_ALS_RNG_0_128 0x04 > + > +/* JSA1212 INT threshold range */ > +#define JSA1212_ALS_TH_MIN 0x0000 > +#define JSA1212_ALS_TH_MAX 0x0FFF > +#define JSA1212_PXS_TH_MIN 0x00 > +#define JSA1212_PXS_TH_MAX 0xFF > + > +#define JSA1212_ALS_DELAY_MS 0xC8 > +#define JSA1212_PXS_DELAY_MS 0x64 > + > +#define JSA1212_DRIVER_NAME "jsa1212" > +#define JSA1212_REGMAP_NAME "jsa1212_regmap" > + > +enum jsa1212_op_mode { > + JSA1212_OPMODE_ALS_EN, > + JSA1212_OPMODE_PXS_EN, > +}; > + > +struct jsa1212_data { > + struct i2c_client *client; > + struct mutex lock; > + u8 als_rng_idx; > + bool als_en; /* ALS enable status */ > + bool pxs_en; /* proximity enable status */ > + struct regmap *regmap; > +}; > + > +/* ALS range idx to val mapping */ > +static const int jsa1212_als_range_val[] = {2048, 1024, 512, 256, 128, > + 128, 128, 128}; > + > +/* Enables or disables ALS function based on status */ > +static int jsa1212_als_enable(struct jsa1212_data *data, u8 status) > +{ > + int ret; > + > + ret = regmap_update_bits(data->regmap, JSA1212_CONF_REG, > + JSA1212_CONF_ALS_MASK, > + status); > + if (ret < 0) > + return ret; > + > + data->als_en = status ? true : false; This could written as: data->als_en = !!status; > + > + return ret; > +} > + > +/* Enables or disables PXS function based on status */ > +static int jsa1212_pxs_enable(struct jsa1212_data *data, u8 status) > +{ > + int ret; > + > + ret = regmap_update_bits(data->regmap, JSA1212_CONF_REG, > + JSA1212_CONF_PXS_MASK, > + status); > + if (ret < 0) > + return ret; > + > + data->pxs_en = status ? true : false; Ditto. > + > + return ret; > +} > + > +static int jsa1212_read_als_data(struct jsa1212_data *data, > + unsigned int *val) > +{ > + int ret; > + u8 als_data[2]; > + > + ret = jsa1212_als_enable(data, JSA1212_CONF_ALS_ENABLE); > + if (ret < 0) > + return ret; > + > + /* Delay for data output */ > + msleep(JSA1212_ALS_DELAY_MS); > + > + /* Read 12 bit data */ > + ret = regmap_bulk_read(data->regmap, JSA1212_ALS_DT1_REG, als_data, 2); > + if (ret < 0) { > + dev_err(&data->client->dev, "als data read err\n"); > + return ret; > + } If this fails, I think you should disable ALS. > + > + *val = le16_to_cpup((__le16 *)als_data); > + > + ret = jsa1212_als_enable(data, JSA1212_CONF_ALS_DISABLE); > + if (ret < 0) > + return ret; > + > + return 0; > +} > + > +static int jsa1212_read_pxs_data(struct jsa1212_data *data, > + unsigned int *val) > +{ > + int ret; > + unsigned int pxs_data; > + > + ret = jsa1212_pxs_enable(data, JSA1212_CONF_PXS_ENABLE); > + if (ret < 0) > + return ret; > + > + /* Delay for data output */ > + msleep(JSA1212_PXS_DELAY_MS); > + > + /* Read out all data */ > + ret = regmap_read(data->regmap, JSA1212_PXS_DATA_REG, &pxs_data); > + if (ret < 0) { > + dev_err(&data->client->dev, "pxs data read err\n"); > + return ret; > + } Ditto. > + > + *val = pxs_data & JSA1212_PXS_DATA_MASK; > + > + ret = jsa1212_pxs_enable(data, JSA1212_CONF_PXS_DISABLE); > + if (ret < 0) > + return ret; > + > + return 0; > +} > + > +static int jsa1212_read_raw(struct iio_dev *indio_dev, > + struct iio_chan_spec const *chan, > + int *val, int *val2, long mask) > +{ > + int ret; > + struct jsa1212_data *data = iio_priv(indio_dev); > + > + switch (mask) { > + case IIO_CHAN_INFO_RAW: > + mutex_lock(&data->lock); > + switch (chan->type) { > + case IIO_LIGHT: > + ret = jsa1212_read_als_data(data, val); > + break; > + case IIO_PROXIMITY: > + ret = jsa1212_read_pxs_data(data, val); > + break; > + default: > + ret = -EINVAL; > + break; > + } > + ret = ret < 0 ? ret : IIO_VAL_INT; > + mutex_unlock(&data->lock); > + break; > + case IIO_CHAN_INFO_SCALE: > + switch (chan->type) { > + case IIO_LIGHT: > + *val = jsa1212_als_range_val[data->als_rng_idx]; > + *val2 = BIT(12); /* Max 12 bit value */ > + ret = IIO_VAL_FRACTIONAL; > + break; How can one change the scale? I'm fine with implementing jsa1212_write_raw in another patch. > + default: > + ret = -EINVAL; > + break; > + } > + break; > + default: > + ret = -EINVAL; > + break; > + } > + > + return ret; > +} > + > +static const struct iio_chan_spec jsa1212_channels[] = { > + { > + .type = IIO_LIGHT, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | > + BIT(IIO_CHAN_INFO_SCALE), > + }, > + { > + .type = IIO_PROXIMITY, > + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), > + } > +}; > + > +static const struct iio_info jsa1212_info = { > + .driver_module = THIS_MODULE, > + .read_raw = &jsa1212_read_raw, > +}; > + > +static int jsa1212_chip_init(struct jsa1212_data *data) > +{ > + int ret; > + > + ret = regmap_write(data->regmap, JSA1212_CONF_REG, > + (JSA1212_CONF_PXS_SLP_50MS | > + JSA1212_CONF_IRDR_ENABLE)); > + if (ret < 0) > + return ret; > + > + ret = regmap_write(data->regmap, JSA1212_INT_REG, > + JSA1212_INT_ALS_PRST_4CONV); > + if (ret < 0) > + return ret; > + > + data->als_rng_idx = JSA1212_ALS_RNG_0_2048; > + > + return 0; > +} > + > +static bool jsa1212_is_volatile_reg(struct device *dev, unsigned int reg) > +{ > + switch (reg) { > + case JSA1212_PXS_DATA_REG: > + case JSA1212_ALS_DT1_REG: > + case JSA1212_ALS_DT2_REG: > + case JSA1212_INT_REG: > + return true; > + default: > + return false; > + } > +} > + > +static struct regmap_config jsa1212_regmap_config = { > + .name = JSA1212_REGMAP_NAME, > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = JSA1212_MAX_REG, > + .cache_type = REGCACHE_RBTREE, > + .volatile_reg = jsa1212_is_volatile_reg, > +}; > + > +static int jsa1212_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct jsa1212_data *jsa1212_data; > + struct iio_dev *indio_dev; > + struct regmap *regmap; > + int ret; > + > + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) > + return -ENODEV; > + > + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*jsa1212_data)); > + if (!indio_dev) > + return -ENOMEM; > + > + regmap = devm_regmap_init_i2c(client, &jsa1212_regmap_config); > + if (IS_ERR(regmap)) { > + dev_err(&client->dev, "Regmap initialization failed.\n"); > + return PTR_ERR(regmap); > + } > + > + jsa1212_data = iio_priv(indio_dev); > + > + i2c_set_clientdata(client, indio_dev); > + jsa1212_data->client = client; > + jsa1212_data->regmap = regmap; > + > + mutex_init(&jsa1212_data->lock); > + > + ret = jsa1212_chip_init(jsa1212_data); > + if (ret < 0) > + return ret; > + > + indio_dev->dev.parent = &client->dev; > + indio_dev->channels = jsa1212_channels; > + indio_dev->num_channels = ARRAY_SIZE(jsa1212_channels); > + indio_dev->name = JSA1212_DRIVER_NAME; > + indio_dev->modes = INDIO_DIRECT_MODE; > + > + indio_dev->info = &jsa1212_info; > + > + ret = iio_device_register(indio_dev); > + if (ret < 0) { > + dev_err(&client->dev, "%s: register device failed\n", __func__); > + return ret; > + } > + > + return 0; > +} > + > + /* power off the device */ > +static int jsa1212_power_off(struct jsa1212_data *data) > +{ > + int ret; > + > + mutex_lock(&data->lock); > + > + ret = regmap_update_bits(data->regmap, JSA1212_CONF_REG, > + JSA1212_CONF_ALS_MASK | > + JSA1212_CONF_PXS_MASK, > + JSA1212_CONF_ALS_DISABLE | > + JSA1212_CONF_PXS_DISABLE); > + > + if (ret < 0) > + dev_err(&data->client->dev, "power off cmd failed\n"); > + > + mutex_unlock(&data->lock); > + > + return ret; > +} > + > + > +static int jsa1212_remove(struct i2c_client *client) > +{ > + struct iio_dev *indio_dev = i2c_get_clientdata(client); > + struct jsa1212_data *data = iio_priv(indio_dev); > + int ret; > + > + iio_device_unregister(indio_dev); > + > + ret = jsa1212_power_off(data); > + > + return ret; No need for ret variable here. You could just return js1212_power_off(data); > +} > + > +#ifdef CONFIG_PM_SLEEP > +static int jsa1212_suspend(struct device *dev) > +{ > + struct jsa1212_data *data; > + > + data = iio_priv(i2c_get_clientdata(to_i2c_client(dev))); > + > + return jsa1212_power_off(data); > +} > + > +static int jsa1212_resume(struct device *dev) > +{ > + int ret = 0; > + struct jsa1212_data *data; > + > + data = iio_priv(i2c_get_clientdata(to_i2c_client(dev))); > + > + mutex_lock(&data->lock); > + > + if (data->als_en) { > + ret = jsa1212_als_enable(data, JSA1212_CONF_ALS_ENABLE); > + if (ret < 0) { > + dev_err(dev, "als resume failed\n"); > + goto unlock_and_ret; > + } > + } > + > + if (data->pxs_en) { > + ret = jsa1212_pxs_enable(data, JSA1212_CONF_PXS_ENABLE); > + if (ret < 0) > + dev_err(dev, "pxs resume failed\n"); > + } > + > +unlock_and_ret: > + mutex_unlock(&data->lock); > + return ret; > +} > + > +static SIMPLE_DEV_PM_OPS(jsa1212_pm_ops, jsa1212_suspend, jsa1212_resume); > + > +#define JSA1212_PM_OPS (&jsa1212_pm_ops) > +#else > +#define JSA1212_PM_OPS NULL > +#endif > + > +static const struct acpi_device_id jsa1212_acpi_match[] = { > + {"JSA1212", 0}, > + { }, > +}; > +MODULE_DEVICE_TABLE(acpi, jsa1212_acpi_match); > + > +static const struct i2c_device_id jsa1212_id[] = { > + { JSA1212_DRIVER_NAME, 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, jsa1212_id); > + > +static struct i2c_driver jsa1212_driver = { > + .driver = { > + .name = JSA1212_DRIVER_NAME, > + .pm = JSA1212_PM_OPS, > + .owner = THIS_MODULE, > + .acpi_match_table = ACPI_PTR(jsa1212_acpi_match), > + }, > + .probe = jsa1212_probe, > + .remove = jsa1212_remove, > + .id_table = jsa1212_id, > +}; > +module_i2c_driver(jsa1212_driver); > + > +MODULE_AUTHOR("Sathya Kuppuswamy "); > +MODULE_DESCRIPTION("JSA1212 proximity/ambient light sensor driver"); > +MODULE_LICENSE("GPL v2"); thanks, Daniel.