From: George McCollister <george.mccollister@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [RFC] x86: baytrail: azalia DT configuration mock-up
Date: Thu, 9 Jun 2016 15:57:12 -0500 [thread overview]
Message-ID: <CAFSKS=NmJ9_dwxaoWdq4gEC8sUgaOiO8i_0NaP=y9WW+sJM4Vw@mail.gmail.com> (raw)
I'm looking for feedback on this mock-up of fsp,azalia-config DT
before I proceed to writing code. I included everything in fsp for
context.
fsp {
compatible = "intel,baytrail-fsp";
fsp,mrc-init-tseg-size = <0>;
fsp,mrc-init-mmio-size = <0x800>;
fsp,mrc-init-spd-addr1 = <0xa0>;
fsp,mrc-init-spd-addr2 = <0xa2>;
fsp,emmc-boot-mode = <2>;
fsp,enable-sdio;
fsp,enable-sdcard;
fsp,enable-hsuart1;
fsp,enable-spi;
fsp,enable-sata;
fsp,sata-mode = <1>;
fsp,enable-azalia;
fsp,azalia-config {
compatible = "intel,baytrail-fsp-azalia-config";
fsp,pme-enable = <1>;
fsp,docking-supported = <1>;
fsp,docking-attached = <0>;
fsp,hdmi-codec-enable = <1>;
fsp,azalia-v-ci-enable = <1>;
fsp,rsvdbits = <0>;
fsp,reset-wait-timer-us = <300>;
alc262 {
compatible = "fsp,azalia-verb-table";
fsp,vendor-device-id = <0x10ec0262>;
fsp,sub-system-id = <0>;
fsp,revision-id = <0xff>;
fsp,front-panel-support = <1>;
fsp,number-of-rear-jacks = <11>;
fsp,number-of-front-jacks = <2>;
fsp,verb-table-data = <
/* Pin Complex (NID 0x11) */
0x01171cf0
0x01171d11
0x01171e11
0x01171f41
/* Pin Complex (NID 0x12) */
0x01271cf0
0x01271d11
0x01271e11
0x01271f41
/* Pin Complex (NID 0x14) */
0x01471c10
0x01471d40
0x01471e01
0x01471f01
/* Pin Complex (NID 0x15) */
0x01571cf0
0x01571d11
0x01571e11
0x01571f41
/* Pin Complex (NID 0x16) */
0x01671cf0
0x01671d11
0x01671e11
0x01671f41
/* Pin Complex (NID 0x18) */
0x01871c20
0x01871d98
0x01871ea1
0x01871f01
/* Pin Complex (NID 0x19) */
0x01971c21
0x01971d98
0x01971ea1
0x01971f02
/* Pin Complex (NID 0x1A) */
0x01a71c2f
0x01a71d30
0x01a71e81
0x01a71f01
/* Pin Complex */
0x01b71c1f
0x01b71d40
0x01b71e21
0x01b71f02
/* Pin Complex */
0x01c71cf0
0x01c71d11
0x01c71e11
0x01c71f41
/* Pin Complex */
0x01d71c01
0x01d71dc6
0x01d71e14
0x01d71f40
/* Pin Complex */
0x01e71cf0
0x01e71d11
0x01e71e11
0x01e71f41
/* Pin Complex */
0x01f71cf0
0x01f71d11
0x01f71e11
0x01f71f41
>;
};
};
fsp,lpss-sio-enable-pci-mode;
fsp,enable-dma0;
fsp,enable-dma1;
fsp,enable-i2c0;
fsp,enable-i2c1;
fsp,enable-i2c2;
fsp,enable-i2c3;
fsp,enable-i2c4;
fsp,enable-i2c5;
fsp,enable-i2c6;
fsp,enable-pwm0;
fsp,enable-pwm1;
fsp,igd-dvmt50-pre-alloc = <2>;
fsp,aperture-size = <2>;
fsp,gtt-size = <2>;
fsp,serial-debug-port-address = <0x3f8>;
fsp,serial-debug-port-type = <1>;
fsp,scc-enable-pci-mode;
fsp,os-selection = <4>;
fsp,emmc45-ddr50-enabled;
fsp,emmc45-retune-timer-value = <8>;
fsp,enable-igd;
fsp,enable-memory-down;
fsp,memory-down-params {
compatible = "intel,baytrail-fsp-mdp";
fsp,dram-speed = <1>;
fsp,dram-type = <1>;
fsp,dimm-0-enable;
fsp,dimm-width = <1>;
fsp,dimm-density = <2>;
fsp,dimm-bus-width = <3>;
fsp,dimm-sides = <0>;
fsp,dimm-tcl = <0xb>;
fsp,dimm-trpt-rcd = <0xb>;
fsp,dimm-twr = <0xc>;
fsp,dimm-twtr = <6>;
fsp,dimm-trrd = <6>;
fsp,dimm-trtp = <6>;
fsp,dimm-tfaw = <0x14>;
};
};
Thanks,
George McCollister
next reply other threads:[~2016-06-09 20:57 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-09 20:57 George McCollister [this message]
2016-06-11 0:17 ` [U-Boot] [RFC] x86: baytrail: azalia DT configuration mock-up Bin Meng
2016-06-13 13:09 ` George McCollister
2016-06-14 2:09 ` Bin Meng
2016-06-14 17:12 ` George McCollister
2016-06-17 5:05 ` Bin Meng
2016-06-17 13:09 ` George McCollister
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAFSKS=NmJ9_dwxaoWdq4gEC8sUgaOiO8i_0NaP=y9WW+sJM4Vw@mail.gmail.com' \
--to=george.mccollister@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.