Re: [PATCH 2/3] ARM: dts: omap3-igep0020: Add HS USB Host support

[Enric Balletbo Serra <eballetbo@gmail.com>]

Hi,

2013/10/5 Javier Martinez Canillas <javier.martinez@collabora.co.uk>:
> Add device nodes for the HS USB Host port 1, USB PHY and its
> required regulator and also pin mux setup for HS USB1 pins.
>
> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
> ---
>  arch/arm/boot/dts/omap3-igep.dtsi    | 22 ++++++++++++++++++++++
>  arch/arm/boot/dts/omap3-igep0020.dts | 25 +++++++++++++++++++++++++
>  2 files changed, 47 insertions(+)
>
> diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
> index 0f92224..ec2ecd2 100644
> --- a/arch/arm/boot/dts/omap3-igep.dtsi
> +++ b/arch/arm/boot/dts/omap3-igep.dtsi
> @@ -27,6 +27,11 @@
>  };
>
>  &omap3_pmx_core {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <
> +               &hsusbb1_pins
> +       >;
> +
>         uart1_pins: pinmux_uart1_pins {
>                 pinctrl-single,pins = <
>                         0x152 (PIN_INPUT | MUX_MODE0)           /* uart1_rx.uart1_rx */
> @@ -78,6 +83,23 @@
>                 >;
>         };
>
> +       hsusbb1_pins: pinmux_hsusbb1_pins {
> +               pinctrl-single,pins = <
> +                       0x5aa (PIN_OUTPUT | MUX_MODE3)          /* etk_ctl.hsusb1_clk */
> +                       0x5a8 (PIN_OUTPUT | MUX_MODE3)          /* etk_clk.hsusb1_stp */
> +                       0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d8.hsusb1_dir */
> +                       0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d9.hsusb1_nxt */
> +                       0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d0.hsusb1_data0 */
> +                       0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d1.hsusb1_data1 */
> +                       0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d2.hsusb1_data2 */
> +                       0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d3.hsusb1_data7 */
> +                       0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d4.hsusb1_data4 */
> +                       0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d5.hsusb1_data5 */
> +                       0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d6.hsusb1_data6 */
> +                       0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d7.hsusb1_data3 */
> +               >;
> +       };
> +
>         leds_pins: pinmux_leds_pins { };
>  };
>
> diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
> index 903e944..180b186 100644
> --- a/arch/arm/boot/dts/omap3-igep0020.dts
> +++ b/arch/arm/boot/dts/omap3-igep0020.dts
> @@ -55,6 +55,23 @@
>                 regulator-name = "vdd33a";
>                 regulator-always-on;
>         };
> +
> +       /* HS USB Port 1 Power */
> +       hsusb1_power: hsusb1_power_reg {
> +               compatible = "regulator-fixed";
> +               regulator-name = "hsusb1_vbus";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>;  /* GPIO LEDA */
> +               startup-delay-us = <70000>;
> +       };
> +
> +       /* HS USB Host PHY on PORT 1 */
> +       hsusb1_phy: hsusb1_phy {
> +               compatible = "usb-nop-xceiv";
> +               reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
> +               vcc-supply = <&hsusb1_power>;
> +       };
>  };
>
>  &leds_pins {
> @@ -173,3 +190,11 @@
>         mode = <3>;
>         power = <50>;
>  };
> +
> +&usbhshost {
> +       port1-mode = "ehci-phy";
> +};
> +
> +&usbhsehci {
> +       phys = <&hsusb1_phy>;
> +};
> --
> 1.8.4.rc3
>

Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>