Re: [PATCH 5/8] pinctrl: qcom/pinctrl-spmi-gpio: Add compatibles for pmic-gpios on SA8155p-adp

[Bhupesh Sharma <bhupesh.sharma@linaro.org>]

Hi Bjorn,

On Fri, 11 Jun 2021 at 08:30, Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
>
> On Mon 07 Jun 06:38 CDT 2021, Bhupesh Sharma wrote:
>
> > SA8155p-adp PMICs (PMM8155AU_1 and PMM8155AU_2) expose
> > the following PMIC GPIO blocks:
> >
> > - PMM8155AU_1: gpio1-gpio10 (with holes on gpio2, gpio5, gpio7 and gpio8)
> > - PMM8155AU_2: gpio1-gpio10 (with holes on gpio2, gpio5, gpio7)
> >
> > Add support for the same in the pinctrl driver.
> >
> > Cc: Linus Walleij <linus.walleij@linaro.org>
> > Cc: Liam Girdwood <lgirdwood@gmail.com>
> > Cc: Mark Brown <broonie@kernel.org>
> > Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Cc: Vinod Koul <vkoul@kernel.org>
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Andy Gross <agross@kernel.org>
> > Cc: devicetree@vger.kernel.org
> > Cc: linux-kernel@vger.kernel.org
> > Cc: linux-gpio@vger.kernel.org
> > Cc: bhupesh.linux@gmail.com
> > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> > ---
> >  drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 4 ++++
> >  1 file changed, 4 insertions(+)
> >
> > diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> > index 00870da0c94e..890c44b6e198 100644
> > --- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> > +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> > @@ -1127,6 +1127,10 @@ static const struct of_device_id pmic_gpio_of_match[] = {
> >       { .compatible = "qcom,pm8150b-gpio", .data = (void *) 12 },
> >       /* pm8150l has 12 GPIOs with holes on 7 */
> >       { .compatible = "qcom,pm8150l-gpio", .data = (void *) 12 },
> > +     /* pmm8155au-1 has 10 GPIOs with holes on 2, 5, 7 and 8 */
> > +     { .compatible = "qcom,pmm8155au-1-gpio", .data = (void *) 10 },
>
> As noted in the binding, I think this should be "qcom,pmm8155au-gpio"
> and please skip the comment about the holes.

Similar to what I noted in the binding patch review thread, the pmic
gpio holes seem different as per the downstream dtsi.

So, please let me know and if required, I can make the suggested change in v2.

Thanks,
Bhupesh

> > +     /* pmm8155au-2 has 10 GPIOs with holes on 2, 5 and 7 */
> > +     { .compatible = "qcom,pmm8155au-2-gpio", .data = (void *) 10 },
> >       { .compatible = "qcom,pm8350-gpio", .data = (void *) 10 },
> >       { .compatible = "qcom,pm8350b-gpio", .data = (void *) 8 },
> >       { .compatible = "qcom,pm8350c-gpio", .data = (void *) 9 },
> > --
> > 2.31.1
> >