---------- Forwarded message --------- From: Chakravarthi Pradeep Date: Sun 5 Aug, 2018, 14:19 Subject: Re: [alsa-devel] ALSA queries To: Hello Takashi, Thanks for your reply. periods_min = the minimal number of periods period_bytes_min = the minimal size of bytes for one period period_bytes_max = the maximal size of bytes for one period periods_min = the minimal number of periods : what is meaning of periods , is it minimal number of interrupts ? period_bytes_min = the minimal size of bytes for one period : it means, minimal size of bytes per interrupt in case of device, Is it correct ? what about period_max ? It's most likely the ALSA PCM core's safety stop; your driver seem to have missed snd_pcm_period_elapsed() calls, so the hwptr isn't updated, resulting in XRUN. ALSA PCM core checks such XRUN condition with the own timer. I'm attaching my driver thread along with this mail. Can you please let me know if I have missed something in audio thread. ?. How to make sure in driver that, trigger stop should be called only when stop command is sent from application. I'm getting cut cut cut ... noise along with audio in VLC application. Initially for 2 or 4 seconds, cut cut cut noise is not heard in VLC application, However after almost after 5 sec ,I can hear cut cut cut noise in VLC application. With my analysis, hwptr is getting updated properly however I have doubt in app_ptr. I'm attaching the excl sheet with hw_ptr,app_ptr and buf_pos values. How to remove the cut cut cut ... noise in audio ? Regards, Chakravarthi On Fri, Aug 3, 2018 at 1:05 PM Takashi Iwai wrote: > > On Thu, 02 Aug 2018 16:31:13 +0200, > Chakravarthi Pradeep wrote: > > > > I'm working on ALSA driver for PCIe card. My ALSA driver and it's > > initializing struct snd_pcm_hardware with below parameter. > > > > /************************ code start > > ************************************************/ > > static struct snd_pcm_hardware audio_pcm_hardware = { > > .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_MMAP | > > SNDRV_PCM_INFO_MMAP_VALID | > > SNDRV_PCM_INFO_BLOCK_TRANSFER | > > SNDRV_PCM_INFO_RESUME ), > > .formats = (SNDRV_PCM_FORMAT_S16_LE | SNDRV_PCM_FORMAT_S24_LE), > > .rates = (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | > > SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_192000), > > .rate_min = 44100, > > .rate_max = 192000, > > .channels_min = 2, > > .channels_max = 8, > > .buffer_bytes_max = 76800, /*75 kbytes */ > > .period_bytes_min = 512,//4410, /* (channel (2) * sample_rate (44100) > > * bit width (24)) / (60 * 8) */ > > .period_bytes_max = 16*1024, > > .periods_min = 10, > > .periods_max = 255, > > > > }; > > /************************ code end > > ************************************************/ > > > > 1) I did not understand what is significance of periods_min , > > period_bytes_min , period_bytes_max and periods_max. Can you please > > tell me what is importance of these parameter and what value should be > > mentioned according into ALSA. > > These three defines the values your hardware may accept: > periods_min = the minimal number of periods > period_bytes_min = the minimal size of bytes for one period > period_bytes_max = the maximal size of bytes for one period > > > 2) snd_pcm_ops trigger callback is getting called in the driver when > > application sends "start" command. But ALSA driver is stopping by > > itself after one frame is copied to ALSA framework, without waiting > > for "stop" command. > > > > For instance: > > In trigger callback , I'm getting these logs after one frame is copied. > > Trigger:Start (When Play button is selected/clicked in application, > > Start command is sent to ALSA driver) > > Dma transfer is completed. > > Trigger:Stop. (When Stop button is selected/clicked in application, > > Stop command is sent to ALSA driver. But stop button is not clicked in > > this case) > > It's most likely the ALSA PCM core's safety stop; your driver seem to > have missed snd_pcm_period_elapsed() calls, so the hwptr isn't > updated, resulting in XRUN. ALSA PCM core checks such XRUN condition > with the own timer. > > > Takashi -- Thanks and Regards Chakravarthi Pradeep.K Ph: 91 9980434900