Re: [PATCH v3 2/3] dt-binding: hwmon: Add documentation for ADM1177

[Rob Herring <robh@kernel.org>]

On Tue, Jan 7, 2020 at 4:58 AM Beniamin Bia <beniamin.bia@analog.com> wrote:
>
> Documentation for ADM1177 was added.
>
> Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> Changes in v3:
> -nothing changed
>
>  .../bindings/hwmon/adi,adm1177.yaml           | 66 +++++++++++++++++++
>  1 file changed, 66 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml

This is breaking linux-next. Please fix and run 'make dt_binding_check':

Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml: while
scanning a block scalar
  in "<unicode string>", line 51, column 5
 found a tab character where an indentation space is expected
  in "<unicode string>", line 61, column 1
>
> diff --git a/Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml b/Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml
> new file mode 100644
> index 000000000000..65ef95328bc6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml
> @@ -0,0 +1,66 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/hwmon/adi,adm1177.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor
> +
> +maintainers:
> +  - Michael Hennerich <michael.hennerich@analog.com>
> +  - Beniamin Bia <beniamin.bia@analog.com>
> +
> +description: |
> +  Analog Devices ADM1177 Hot Swap Controller and Digital Power Monitor
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1177.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,adm1177
> +
> +  reg:
> +    maxItems: 1
> +
> +  avcc-supply:
> +    description:
> +      Phandle to the Avcc power supply
> +
> +  shunt-resistor-micro-ohms:
> +    description:
> +      The value of curent sense resistor in microohms. If not provided,
> +      the current reading and overcurrent alert is disabled.
> +
> +  adi,shutdown-threshold-microamp:
> +    description:
> +      Specifies the current level at which an over current alert occurs.
> +      If not provided, the overcurrent alert is configured to max ADC range
> +      based on shunt-resistor-micro-ohms.
> +
> +  adi,vrange-high-enable:
> +    description:
> +      Specifies which internal voltage divider to be used. A 1 selects
> +      a 7:2 voltage divider while a 0 selects a 14:1 voltage divider.
> +    type: boolean
> +
> +required:
> +  - compatible
> +  - reg
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    i2c0 {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        pwmon@5a {
> +                compatible = "adi,adm1177";
> +                reg = <0x5a>;
> +               shunt-resistor-micro-ohms = <50000>; /* 50 mOhm */
> +                adi,shutdown-threshold-microamp = <1059000>; /* 1.059 A */
> +                adi,vrange-high-enable;
> +        };
> +    };
> +...
> --
> 2.17.1
>