All of lore.kernel.org
 help / color / mirror / Atom feed
From: Geert Uytterhoeven <geert@linux-m68k.org>
To: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Cc: Linus Walleij <linus.walleij@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	"open list:GPIO SUBSYSTEM" <linux-gpio@vger.kernel.org>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
	<devicetree@vger.kernel.org>,
	Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
	Linux-Renesas <linux-renesas-soc@vger.kernel.org>,
	Prabhakar <prabhakar.csengg@gmail.com>,
	Biju Das <biju.das.jz@bp.renesas.com>
Subject: Re: [PATCH v2 5/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength and output-impedance-ohms
Date: Mon, 8 Nov 2021 16:40:24 +0100	[thread overview]
Message-ID: <CAMuHMdXwJ043PuJnNU=L9+oN05ExjU-Km9CWBoXO9zqAVizByg@mail.gmail.com> (raw)
In-Reply-To: <20211029124437.20721-6-prabhakar.mahadev-lad.rj@bp.renesas.com>

Hi Prabhakar,

On Fri, Oct 29, 2021 at 2:45 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> RZ/G2L supports two groups of pins Group-A and Group-B. For Group-A
> pins drive-strength can be configured and for Group-B output-impedance
> can be configured.
>
> This patch splits PIN_CFG_IOLH macro to PIN_CFG_IOLH_A/B and adds
> support to get/set drive-strength and output-impedance-ohms for the
> supported pins.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>

Thanks for your patch!

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c

> @@ -501,7 +507,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>         unsigned int arg = 0;
>         unsigned long flags;
>         void __iomem *addr;
> -       u32 port = 0;
> +       u32 port = 0, reg;

"unsigned int index", for symmetry with rzg2l_pinctrl_pinconf_set()?

>         u32 cfg = 0;
>         u8 bit = 0;
>
> @@ -549,6 +555,24 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
>                 break;
>         }
>
> +       case PIN_CONFIG_DRIVE_STRENGTH: {
> +               if (!(cfg & PIN_CFG_IOLH_A))
> +                       return -EINVAL;
> +
> +               reg = rzg2l_read_pin_config(pctrl, port_pin, IOLH(port), bit, IOLH_MASK);

port_pin still under discussion, cfr. my comments for the other
patches in this series.

The rest looks good to me, so
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

  reply	other threads:[~2021-11-08 15:40 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-10-29 12:44 [PATCH v2 0/5] RZ/G2L: pinctrl: Support to get/set drive-strength and output-impedance-ohms Lad Prabhakar
2021-10-29 12:44 ` [PATCH v2 1/5] dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Add output-impedance-ohms property Lad Prabhakar
2021-11-08 20:56   ` Rob Herring
2021-10-29 12:44 ` [PATCH v2 2/5] pinctrl: renesas: pinctrl-rzg2l: Add helper functions to read/write pin config Lad Prabhakar
2021-11-08 15:32   ` Geert Uytterhoeven
2021-10-29 12:44 ` [PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins Lad Prabhakar
2021-11-08 15:35   ` Geert Uytterhoeven
2021-11-09 14:31     ` Lad, Prabhakar
2021-11-09 15:00       ` Geert Uytterhoeven
2021-11-09 15:24         ` Lad, Prabhakar
2021-10-29 12:44 ` [PATCH v2 4/5] pinctrl: renesas: pinctrl-rzg2l: Rename PIN_CFG_* macros to match HW manual Lad Prabhakar
2021-11-08 14:13   ` Geert Uytterhoeven
2021-10-29 12:44 ` [PATCH v2 5/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set drive-strength and output-impedance-ohms Lad Prabhakar
2021-11-08 15:40   ` Geert Uytterhoeven [this message]
2021-11-10 13:39     ` Lad, Prabhakar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CAMuHMdXwJ043PuJnNU=L9+oN05ExjU-Km9CWBoXO9zqAVizByg@mail.gmail.com' \
    --to=geert@linux-m68k.org \
    --cc=biju.das.jz@bp.renesas.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=prabhakar.csengg@gmail.com \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.