attrib_bleep Beeps the PC speaker when there is an attribute change such as foreground or background color when using speakup review commands. One = on, zero = off. bell_pos This works much like a typewriter bell. If for example 72 is echoed to bell_pos, it will beep the PC speaker when typing on a line past character 72. bleeps This controls whether one hears beeps through the PC speaker when using speakup's review commands. bleep_time This controls the duration of the PC speaker beeps speakup produces. TODO: What are the units? Jiffies? cursor_time This controls cursor delay when using arrow keys. When a connection is very slow, with the default setting, when moving with the arrows, or backspacing etc. speakup says the incorrect characters. Set this to a higher value to adjust for the delay and better synchronisation between cursor position and speech. delimiters Delimit a word from speakup. TODO: add more info ex_num TODO: key_echo Controls if speakup speaks keys when they are typed. One = on, zero = off or don't echo keys. keymap Speakup keymap remaps keys to Speakup functins. It uses a binary format. A special program called genmap is needed to compile a textual keymap into the binary format which is then loaded into /sys/accessibility/speakup/keymap. no_interrupt Controls if typing interrupts output from speakup. With no_interrupt set to zero, typing on the keyboard will interrupt speakup if for example the say screen command is used before the entire screen is read. With no_interrupt set to one, if the say screen command is used, and one then types on the keyboard, speakup will continue to say the whole screen regardless until it finishes. punc_all This is a list of all the punctuation speakup should speak when punc_level is set to four. punc_level Controls the level of punctuation spoken as the screen is displayed, not reviewed. Levels range from zero no punctuation, to four, all punctuation. One corresponds to punc_some, two corresponds to punc_most, and three as well as four both correspond to punc_all. Some hardware synthesizers may have different levels each corresponding to three and four for punc_level. Also note that if punc_level is set to zero, and key_echo is set to one, typed punctuation is still spoken as it is typed. punc_most This is a list of all the punctuation speakup should speak when punc_level is set to two. punc_some This is a list of all the punctuation speakup should speak when punc_level is set to one. reading_punc Almost the same as punc_level, the differences being that reading_punc controls the level of punctuation when reviewing the screen with speakup's screen review commands. The other difference is that reading_punc set to three speaks punc_all, and reading_punc set to four speaks all punctuation, including spaces. repeats A list of characters speakup repeats. Normally, when there are more than three characters in a row, speakup just reads three of those characters. For example, "......" would be read as dot, dot, dot. If a . is added to the list of characters in repeats, "......" would be read as dot, dot, dot, times six. say_control If set to one, speakup speaks shift, alt and control when those keys are pressed. If say_control is set to zero, shift, ctrl, and alt are not spoken when they are pressed. say_word_ctl TODO: silent TODO: spell_delay This controls how fast a word is spelled when speakup's say word review command is pressed twice quickly to speak the current word being reviewed. Zero just speaks the letters one after another, while values one through four seem to introduce more of a pause between the spelling of each letter by speakup. synth Gets or sets the synthesizer driver currently in use. Reading synth returns the synthesizer driver currently in use. Writing synth switches to the given synthesizer driver, provided it is either built into the kernel, or already loaded as a module. synth_direct Sends whatever is written to synth_direct directly to the speech synthesizer in use, bypassing speakup. This could be used to make the synthesizer speak a string, or to send control sequences to the synthesizer to change how the synthesizer behaves. version Reading version returns the version of speakup, and the version of the synthesizer driver currently in use. Synthesizer Driver Parameters In `/sys/accessibility/speakup` is a directory corresponding to the synthesizer driver currently in use (E.G) `soft` for the soft driver. This directory contains files which control the speech synthesizer itself, as opposed to controlling the speakup screen reader. The parameters in this directory have the same names and functions across all supported synthesizers. The range of values for freq, pitch, rate, and vol is the same for all supported synthesizers, with the given range being internally mapped by the driver to more or less fit the range of values supported for a given parameter by the individual synthesizer. Below is a description of values and parameters for soft synthesizer, which is currently the most commonly used. caps_start This is the string that is sent to the synthesizer to cause it to start speaking uppercase letters. For the soft synthesizer and most others, this causes the pitch of the voice to rise above the currently set pitch. caps_stop This is the string sent to the synthesizer to cause it to stop speaking uppercase letters. In the case of the soft synthesizer and most others, this returns the pitch of the voice down to the currently set pitch. delay_time TODO: direct Controls if punctuation is spoken by speakup, or by the synthesizer. For example, speakup speaks ">" as "greater", while the espeak synthesizer used by the soft driver speaks "greater than". Zero lets speakup speak the punctuation. One lets the synthesizer itself speak punctuation. freq Gets or sets the frequency of the speech synthesizer. Range is 0-9. full_time TODO: jiffy_delta This controls how many jiffys the kernel gives to the synthesizer. Setting this too high can make a system unstable, or even crash it. pitch Gets or sets the pitch of the synthesizer. The range is 0-9. punct Gets or sets the amount of punctuation spoken by the synthesizer. The range for the soft driver seems to be 0-2. TODO: How is this related to speakup's punc_level, or reading_punc rate Gets or sets the rate of the synthesizer. Range is from zero slowest, to nine fastest. tone Gets or sets the tone of the speech synthesizer. The range for the soft driver seems to be 0-2. This seems to make no difference if using espeak and the espeakup connector. TODO: does espeakup support different tonalities? trigger_time Don't know. voice Gets or sets the voice used by the synthesizer if the synthesizer can speak in more than one voice. The range for the soft driver is 0-7. Note that while espeak supports multiple voices, this parameter will not set the voice when the espeakup connector is used between speakup and espeak. vol Gets or sets the volume of the speech synthesizer. Range is 0-9, with zero being the softest, and nine being the loudest.