From: Dave Stevenson <dave.stevenson@raspberrypi.com>
To: Adam Ford <aford173@gmail.com>
Cc: Linux Media Mailing List <linux-media@vger.kernel.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
LKML <linux-kernel@vger.kernel.org>,
Adam Ford-BE <aford@beaconembedded.com>
Subject: Re: [PATCH V2 1/2] media: i2c: imx219: Split common registers from mode tables
Date: Tue, 21 Jun 2022 16:46:21 +0100 [thread overview]
Message-ID: <CAPY8ntCmov0OY3tBabf7ndSVCNgeYeSy+e4E0sdaW54zZpoauw@mail.gmail.com> (raw)
In-Reply-To: <20220616123150.5890-1-aford173@gmail.com>
Hi Adam
Thanks for the patch, and sorry it's taken me a few days to get to it.
On Thu, 16 Jun 2022 at 13:31, Adam Ford <aford173@gmail.com> wrote:
>
> There are four modes, and each mode has a table of registers.
> Some of the registers are common to all modes, so create new
> tables for these common registers to reduce duplicate code.
>
> Signed-off-by: Adam Ford <aford173@gmail.com>
> ---
> V2: Merge the PLL table into the common table instead of having
> two separate, common tables.
>
> diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
> index e10af3f74b38..a43eed143999 100644
> --- a/drivers/media/i2c/imx219.c
> +++ b/drivers/media/i2c/imx219.c
> @@ -145,23 +145,60 @@ struct imx219_mode {
> struct imx219_reg_list reg_list;
> };
>
> -/*
> - * Register sets lifted off the i2C interface from the Raspberry Pi firmware
> - * driver.
> - * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
> - */
> -static const struct imx219_reg mode_3280x2464_regs[] = {
> - {0x0100, 0x00},
> +/* To Access Addresses 3000-5fff, send the following commands */
> +static const struct imx219_reg imx219_common_regs[] = {
> + {0x0100, 0x00}, /* Mode Select */
> +
> + /* Access Command Sequence */
> {0x30eb, 0x0c},
> {0x30eb, 0x05},
> {0x300a, 0xff},
> {0x300b, 0xff},
> {0x30eb, 0x05},
> {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> +
> + /* PLL Clock Table */
> + {0x0301, 0x05}, /* VTPXCK_DIV */
> + {0x0303, 0x01}, /* VTSYSCK_DIV */
> + {0x0304, 0x03}, /* PREPLLCK_VT_DIV 0x03 = AUTO set */
> + {0x0305, 0x03}, /* PREPLLCK_OP_DIV 0x03 = AUTO set */
> + {0x0306, 0x00}, /* PLL_VT_MPY */
> + {0x0307, 0x39},
> + {0x030b, 0x01}, /* OP_SYS_CLK_DIV */
> + {0x030c, 0x00}, /* PLL_OP_MPY */
> + {0x030d, 0x72},
> +
> + /* Undocumented registers */
> + {0x455e, 0x00},
> + {0x471e, 0x4b},
> + {0x4767, 0x0f},
> + {0x4750, 0x14},
> + {0x4540, 0x00},
> + {0x47b4, 0x14},
> + {0x4713, 0x30},
> + {0x478b, 0x10},
> + {0x478f, 0x10},
> + {0x4793, 0x10},
> + {0x4797, 0x0e},
> + {0x479b, 0x0e},
> +
> + /* Frame Bank Register Group "A" */
> + {0x0162, 0x0d}, /* Line_Length_A */
> + {0x0163, 0x78},
Registers 0x0170 and 0x171 for X_ODD_INC_A and Y_ODD_INC_A are also
common to all modes as 0x01. You could have modes with skipping, but
currently there are none.
> +
> + /* Output setup registers */
> + {0x0114, 0x01}, /* CSI 2-Lane Mode */
> + {0x0128, 0x00}, /* DPHY Auto Mode */
> + {0x012a, 0x18}, /* EXCK_Freq */
> {0x012b, 0x00},
> +};
> +
> +/*
> + * Register sets lifted off the i2C interface from the Raspberry Pi firmware
> + * driver.
> + * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
> + */
> +static const struct imx219_reg mode_3280x2464_regs[] = {
> {0x0164, 0x00},
> {0x0165, 0x00},
> {0x0166, 0x0c},
> @@ -176,51 +213,15 @@ static const struct imx219_reg mode_3280x2464_regs[] = {
> {0x016f, 0xa0},
> {0x0170, 0x01},
> {0x0171, 0x01},
> - {0x0174, 0x00},
> + {0x0174, 0x00}, /* No-Binning */
> {0x0175, 0x00},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x0c},
> {0x0625, 0xd0},
> {0x0626, 0x09},
> {0x0627, 0xa0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> };
>
> static const struct imx219_reg mode_1920_1080_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x05},
> - {0x30eb, 0x0c},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> {0x0164, 0x02},
> {0x0165, 0xa8},
> {0x0166, 0x0a},
> @@ -235,47 +236,15 @@ static const struct imx219_reg mode_1920_1080_regs[] = {
> {0x016f, 0x38},
> {0x0170, 0x01},
> {0x0171, 0x01},
> - {0x0174, 0x00},
> + {0x0174, 0x00}, /* No-Binning */
> {0x0175, 0x00},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x07},
> {0x0625, 0x80},
> {0x0626, 0x04},
> {0x0627, 0x38},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> };
>
> static const struct imx219_reg mode_1640_1232_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x0c},
> - {0x30eb, 0x05},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> {0x0164, 0x00},
> {0x0165, 0x00},
> {0x0166, 0x0c},
> @@ -290,51 +259,15 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
> {0x016f, 0xd0},
> {0x0170, 0x01},
> {0x0171, 0x01},
> - {0x0174, 0x01},
> + {0x0174, 0x01}, /* x2-Binning */
> {0x0175, 0x01},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x06},
> {0x0625, 0x68},
> {0x0626, 0x04},
> {0x0627, 0xd0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> };
>
> static const struct imx219_reg mode_640_480_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x05},
> - {0x30eb, 0x0c},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> {0x0164, 0x03},
> {0x0165, 0xe8},
> {0x0166, 0x08},
> @@ -349,33 +282,12 @@ static const struct imx219_reg mode_640_480_regs[] = {
> {0x016f, 0xe0},
> {0x0170, 0x01},
> {0x0171, 0x01},
> - {0x0174, 0x03},
> + {0x0174, 0x03}, /* x2-analog binning */
> {0x0175, 0x03},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x06},
> {0x0625, 0x68},
> {0x0626, 0x04},
> {0x0627, 0xd0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> };
>
> static const struct imx219_reg raw8_framefmt_regs[] = {
> @@ -1041,6 +953,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
> if (ret < 0)
> return ret;
>
> + /* Send the Manufacturing Header common to all modes */
It's a table of common settings, not a manufacturing header.
s/Send the Manufacturing Header/Send all registers that are
Dave
> + ret = imx219_write_regs(imx219, imx219_common_regs, ARRAY_SIZE(imx219_common_regs));
> + if (ret) {
> + dev_err(&client->dev, "%s failed to send mfg header\n", __func__);
> + goto err_rpm_put;
> + }
> +
> /* Apply default values of current mode */
> reg_list = &imx219->mode->reg_list;
> ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
> --
> 2.34.1
>
next prev parent reply other threads:[~2022-06-21 15:46 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-06-16 12:31 [PATCH V2 1/2] media: i2c: imx219: Split common registers from mode tables Adam Ford
2022-06-16 12:31 ` [PATCH V2 2/2] media: i2c: imx219: Support four-lane operation Adam Ford
2022-06-21 16:05 ` Dave Stevenson
2022-06-21 17:08 ` Adam Ford
2022-06-21 17:31 ` Dave Stevenson
2022-06-21 15:46 ` Dave Stevenson [this message]
2022-06-21 15:58 ` [PATCH V2 1/2] media: i2c: imx219: Split common registers from mode tables Adam Ford
2022-06-21 16:23 ` Dave Stevenson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAPY8ntCmov0OY3tBabf7ndSVCNgeYeSy+e4E0sdaW54zZpoauw@mail.gmail.com \
--to=dave.stevenson@raspberrypi.com \
--cc=aford173@gmail.com \
--cc=aford@beaconembedded.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.