From mboxrd@z Thu Jan 1 00:00:00 1970 From: "Ian Dobson" Date: Sun, 06 Feb 2011 16:03:15 +0000 Subject: Re: [lm-sensors] Standalone driver for W83677HG-I, NCT6775F, Message-Id: List-Id: References: <20110205175852.GA26672@ericsson.com> In-Reply-To: <20110205175852.GA26672@ericsson.com> MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 8bit To: lm-sensors@vger.kernel.org -------------------------------------------------- From: "Jean Delvare" Sent: Sunday, February 06, 2011 4:53 PM To: "Ian Dobson" Cc: Subject: Re: [lm-sensors] Standalone driver for W83677HG-I, NCT6775F, NCT6776F voltage input multipliers > On Sun, 6 Feb 2011 14:37:48 +0100, Ian Dobson wrote: >> OK Here's the infomation >> nct6776-isa-0290 >> Adapter: ISA adapter >> Vcore: +1.18 V (min = +0.00 V, max = +1.74 V) >> in1: +1.02 V (min = +0.00 V, max = +0.00 V) ALARM >> AVCC: +3.36 V (min = +2.98 V, max = +3.63 V) >> +3.3V: +3.34 V (min = +2.98 V, max = +3.63 V) >> in4: +1.03 V (min = +0.00 V, max = +0.00 V) ALARM >> in5: +2.04 V (min = +0.00 V, max = +0.00 V) ALARM >> in6: +0.78 V (min = +0.00 V, max = +0.00 V) ALARM >> 3VSB: +3.42 V (min = +2.98 V, max = +3.63 V) >> Vbat: +3.30 V (min = +2.70 V, max = +3.30 V) ALARM >> fan1: 550 RPM (min = 0 RPM) ALARM >> fan2: 1013 RPM (min = 0 RPM) ALARM >> fan3: 0 RPM (min = 0 RPM) ALARM >> fan4: 824 RPM (min = 0 RPM) ALARM >> fan5: 0 RPM (min = 0 RPM) ALARM >> temp1: +24.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor >> >> thermistor >> temp2: -60.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode >> temp3: +38.0°C (high = +80.0°C, hyst = +75.0°C) sensor >> thermistor >> cpu0_vid: +2.050 V >> >> and BIOS >> CPU temp 43 >> MB temp 25 >> >> CPU Volt 1.114-1.1176 >> 3.3Volt 3.36 - 3.34 >> 5Volt 5.160 >> 12Volt 12.288 >> >> So it looks as if in4 * 5 is 5Volt, in5 * 6 is 12volt. This is on a asus >> p8p67 pro, but I've seen the same values on a asus p8p67 delux. > > in4 * 5 = 5V is possible, in5 * 6 = 12V is not. 2.04 is the saturation > value for the ADC so it looks like in5 isn't used on your system. I'd > rather think that in1 * 12 = 12V. > >> Looking in the n6776f specification if looks as if AUXTIN(temp3) and in6 >> share the same pin (pin 109) so we can't have both enabled. > > This was the case on the W83667HG already, so I'm not surprised, and it > should be very easy to implement in the driver. > > -- > Jean Delvare Yep, your right, here's the config I'm now using and the output chip "nct6775-*" "nct6776-*" # nct6776 values for Asus p8p67 pro label temp1 "Motherboard" ignore temp2 label temp3 "CPU" label in0 "Vcore" set in0_min 1.1 * 0.85 set in0_max 1.1 * 1.20 label in1 "+12V" compute in1 @ * 12, @ / 12 set in1_min 12 * 0.90 set in1_max 12 * 1.15 label in2 "AVCC" set in2_min 3.3 * 0.90 set in2_max 3.3 * 1.10 label in3 "+3.3V" set in3_min 3.3 * 0.90 set in3_max 3.3 * 1.10 label in4 "+5V" compute in4 @ * 5, @ / 5 set in4_min 5 * 0.90 set in4_max 5 * 1.10 ignore in6 label in7 "3VSB" set in7_min 3.3 * 0.90 set in7_min 3.3 * 0.90 set in7_max 3.3 * 1.10 label in8 "Vbat" set in8_min 3.0 * 0.90 set in8_max 3.0 * 1.15 nct6776-isa-0290 Adapter: ISA adapter Vcore: +1.18 V (min = +0.94 V, max = +1.32 V) +12V: +12.29 V (min = +10.85 V, max = +13.82 V) AVCC: +3.36 V (min = +2.98 V, max = +3.63 V) +3.3V: +3.34 V (min = +2.98 V, max = +3.63 V) +5V: +5.16 V (min = +4.52 V, max = +5.52 V) in5: +2.04 V (min = +1.80 V, max = +2.04 V) ALARM 3VSB: +3.42 V (min = +2.98 V, max = +3.63 V) Vbat: +3.30 V (min = +2.70 V, max = +3.46 V) fan1: 526 RPM (min = 0 RPM) ALARM fan2: 995 RPM (min = 0 RPM) ALARM fan3: 0 RPM (min = 0 RPM) ALARM fan4: 773 RPM (min = 0 RPM) ALARM fan5: 0 RPM (min = 0 RPM) ALARM Motherboard: +23.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = thermistor CPU: +37.5°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor cpu0_vid: +2.050 V Note 5V and 12V correspond to bios within 0.01volt Regards Ian Dobson _______________________________________________ lm-sensors mailing list lm-sensors@lm-sensors.org http://lists.lm-sensors.org/mailman/listinfo/lm-sensors