All of lore.kernel.org
 help / color / mirror / Atom feed
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>,
	niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org,
	Mauro Carvalho Chehab <mchehab@kernel.org>,
	linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH 13/16] media: i2c: rdacm2x: Implement .init() subdev op
Date: Mon, 22 Feb 2021 03:52:41 +0200	[thread overview]
Message-ID: <YDMOaZUi8Q1vWq9j@pendragon.ideasonboard.com> (raw)
In-Reply-To: <ce1673db-9ea7-f28c-a22a-0d129c0bff98@ideasonboard.com>

Hi Jacopo,

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

On Thu, Feb 18, 2021 at 04:13:14PM +0000, Kieran Bingham wrote:
> On 16/02/2021 17:41, Jacopo Mondi wrote:
> > The current probe() procedure of the RDACM20 and RDACM20 performs
> 
> and RDACM21?
> 
> > initialization of the serializer image sensors and increases the noise
> 
> Of the serializer 'and' image sensors ?
> or perhaps just
> 
> s/serializer/serializer,/ ?
> 
> > immunity threshold as last operation, which is then compensated by the
> 
> as a last operation
> or
> as a final operation
> 
> 
> > remote deserializer by increasing the reverse channel signal amplitude
> > once all remotes have bound.
> > 
> > The probe routine is then run without noise immunity activated which

Maybe s/then/thus/ ? I initially interpreted this as meaning the probe
routine is run after the operations listed above.

> > in noisy environment conditions makes the probe sequence less reliable as
> > the chips configuration requires a relevant amount of i2c transactions.
> 
> s/relevant/relatively high/ ?
> 
> > Break chip initialization in two:
> > - At probe time only configure the serializer's reverse channel with
> >   noise immunity activated, to reduce the number of transactions
> >   performed without noise immunity protection
> > - Move the chips initialization to the .init() core subdev operation to
> >   be invoked by the deserializer after the camera has probed and it has
> >   increased the reverse channel amplitude
> 
> Is this the op you said was deprecated?
> 
> 
> Functionally in this code, it seems fine, but as mentioned on the next
> patch, I suspect it might need squashing to make sure it stays functional...
> 
> I'm not fully sure of the implications of this patch, but your tests
> have reportede that this series is helping a lot with reliability so I
> don't want to block it.
> 
> The code changes themselves look ok, with the following thougts:
> 
>  - If this op/methodology is deprecated it might be harder to get
>    acceptance?

I think we need to propose de-deprecating the operation, which should
include a clear explanation of the valid use cases.

>  - now we have _init and _initialise - should that be made more
>    distinct?
> 
>  - Seeing the duplication of the MAX9271_DEFAULT_ADDR / ping again
>    really makes me want to see that wrapped in the max9271.c ;-)
> 
>  - Likely needs squashed with relevant changes in max9286?

I share the bisectability concerns.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> But even with those thoughts, I don't think this is necessarily wrong so:
> 
> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> 
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> > ---
> >  drivers/media/i2c/rdacm20.c | 65 ++++++++++++++++++++++---------------
> >  drivers/media/i2c/rdacm21.c | 65 ++++++++++++++++++++++---------------
> >  2 files changed, 78 insertions(+), 52 deletions(-)
> > 
> > diff --git a/drivers/media/i2c/rdacm20.c b/drivers/media/i2c/rdacm20.c
> > index 39e4b4241870..0632ef98eea7 100644
> > --- a/drivers/media/i2c/rdacm20.c
> > +++ b/drivers/media/i2c/rdacm20.c
> > @@ -437,36 +437,12 @@ static int rdacm20_get_fmt(struct v4l2_subdev *sd,
> >  	return 0;
> >  }
> >  
> > -static const struct v4l2_subdev_video_ops rdacm20_video_ops = {
> > -	.s_stream	= rdacm20_s_stream,
> > -};
> > -
> > -static const struct v4l2_subdev_pad_ops rdacm20_subdev_pad_ops = {
> > -	.enum_mbus_code = rdacm20_enum_mbus_code,
> > -	.get_fmt	= rdacm20_get_fmt,
> > -	.set_fmt	= rdacm20_get_fmt,
> > -};
> > -
> > -static const struct v4l2_subdev_ops rdacm20_subdev_ops = {
> > -	.video		= &rdacm20_video_ops,
> > -	.pad		= &rdacm20_subdev_pad_ops,
> > -};
> > -
> > -static int rdacm20_initialize(struct rdacm20_device *dev)
> > +static int rdacm20_init(struct v4l2_subdev *sd, unsigned int val)
> >  {
> > +	struct rdacm20_device *dev = sd_to_rdacm20(sd);
> >  	unsigned int i;
> >  	int ret;
> >  
> > -	/* Verify communication with the MAX9271: ping to wakeup. */
> > -	dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
> > -	i2c_smbus_read_byte(dev->serializer.client);
> > -	usleep_range(5000, 8000);
> > -
> > -	/* Serial link disabled during config as it needs a valid pixel clock. */
> > -	ret = max9271_set_serial_link(&dev->serializer, false);
> > -	if (ret)
> > -		return ret;
> > -
> >  	/*
> >  	 *  Ensure that we have a good link configuration before attempting to
> >  	 *  identify the device.
> > @@ -537,6 +513,43 @@ static int rdacm20_initialize(struct rdacm20_device *dev)
> >  
> >  	dev_info(dev->dev, "Identified RDACM20 camera module\n");
> >  
> > +	return 0;
> > +}
> > +
> > +static const struct v4l2_subdev_core_ops rdacm20_core_ops = {
> > +	.init           = rdacm20_init,
> > +};
> > +
> > +static const struct v4l2_subdev_video_ops rdacm20_video_ops = {
> > +	.s_stream	= rdacm20_s_stream,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops rdacm20_subdev_pad_ops = {
> > +	.enum_mbus_code = rdacm20_enum_mbus_code,
> > +	.get_fmt	= rdacm20_get_fmt,
> > +	.set_fmt	= rdacm20_get_fmt,
> > +};
> > +
> > +static const struct v4l2_subdev_ops rdacm20_subdev_ops = {
> > +	.core		= &rdacm20_core_ops,
> > +	.video		= &rdacm20_video_ops,
> > +	.pad		= &rdacm20_subdev_pad_ops,
> > +};
> > +
> > +static int rdacm20_initialize(struct rdacm20_device *dev)
> > +{
> > +	int ret;
> > +
> > +	/* Verify communication with the MAX9271: ping to wakeup. */
> > +	dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
> > +	i2c_smbus_read_byte(dev->serializer.client);
> > +	usleep_range(5000, 8000);
> > +
> > +	/* Serial link disabled during config as it needs a valid pixel clock. */
> > +	ret = max9271_set_serial_link(&dev->serializer, false);
> > +	if (ret)
> > +		return ret;
> > +
> >  	/*
> >  	 * Set reverse channel high threshold to increase noise immunity.
> >  	 *
> > diff --git a/drivers/media/i2c/rdacm21.c b/drivers/media/i2c/rdacm21.c
> > index c420a6b96879..80b6f16f87a8 100644
> > --- a/drivers/media/i2c/rdacm21.c
> > +++ b/drivers/media/i2c/rdacm21.c
> > @@ -314,21 +314,6 @@ static int rdacm21_get_fmt(struct v4l2_subdev *sd,
> >  	return 0;
> >  }
> >  
> > -static const struct v4l2_subdev_video_ops rdacm21_video_ops = {
> > -	.s_stream	= rdacm21_s_stream,
> > -};
> > -
> > -static const struct v4l2_subdev_pad_ops rdacm21_subdev_pad_ops = {
> > -	.enum_mbus_code = rdacm21_enum_mbus_code,
> > -	.get_fmt	= rdacm21_get_fmt,
> > -	.set_fmt	= rdacm21_get_fmt,
> > -};
> > -
> > -static const struct v4l2_subdev_ops rdacm21_subdev_ops = {
> > -	.video		= &rdacm21_video_ops,
> > -	.pad		= &rdacm21_subdev_pad_ops,
> > -};
> > -
> >  static int ov10640_initialize(struct rdacm21_device *dev)
> >  {
> >  	u8 val;
> > @@ -448,20 +433,11 @@ static int ov490_initialize(struct rdacm21_device *dev)
> >  	return 0;
> >  }
> >  
> > -static int rdacm21_initialize(struct rdacm21_device *dev)
> > +static int rdacm21_init(struct v4l2_subdev *sd, unsigned int val)
> >  {
> > +	struct rdacm21_device *dev = sd_to_rdacm21(sd);
> >  	int ret;
> >  
> > -	/* Verify communication with the MAX9271: ping to wakeup. */
> > -	dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
> > -	i2c_smbus_read_byte(dev->serializer.client);
> > -	usleep_range(5000, 8000);
> > -
> > -	/* Enable reverse channel and disable the serial link. */
> > -	ret = max9271_set_serial_link(&dev->serializer, false);
> > -	if (ret)
> > -		return ret;
> > -
> >  	/* Configure I2C bus at 105Kbps speed and configure GMSL. */
> >  	ret = max9271_configure_i2c(&dev->serializer,
> >  				    MAX9271_I2CSLVSH_469NS_234NS |
> > @@ -508,6 +484,43 @@ static int rdacm21_initialize(struct rdacm21_device *dev)
> >  	if (ret)
> >  		return ret;
> >  
> > +	return 0;
> > +}
> > +
> > +static const struct v4l2_subdev_core_ops rdacm21_core_ops = {
> > +	.init		= rdacm21_init,
> > +};
> > +
> > +static const struct v4l2_subdev_video_ops rdacm21_video_ops = {
> > +	.s_stream	= rdacm21_s_stream,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops rdacm21_subdev_pad_ops = {
> > +	.enum_mbus_code = rdacm21_enum_mbus_code,
> > +	.get_fmt	= rdacm21_get_fmt,
> > +	.set_fmt	= rdacm21_get_fmt,
> > +};
> > +
> > +static const struct v4l2_subdev_ops rdacm21_subdev_ops = {
> > +	.core		= &rdacm21_core_ops,
> > +	.video		= &rdacm21_video_ops,
> > +	.pad		= &rdacm21_subdev_pad_ops,
> > +};
> > +
> > +static int rdacm21_initialize(struct rdacm21_device *dev)
> > +{
> > +	int ret;
> > +
> > +	/* Verify communication with the MAX9271: ping to wakeup. */
> > +	dev->serializer.client->addr = MAX9271_DEFAULT_ADDR;
> > +	i2c_smbus_read_byte(dev->serializer.client);
> > +	usleep_range(5000, 8000);
> > +
> > +	/* Enable reverse channel and disable the serial link. */
> > +	ret = max9271_set_serial_link(&dev->serializer, false);
> > +	if (ret)
> > +		return ret;
> > +
> >  	/*
> >  	 * Set reverse channel high threshold to increase noise immunity.
> >  	 *

-- 
Regards,

Laurent Pinchart

  reply	other threads:[~2021-02-22  1:54 UTC|newest]

Thread overview: 65+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-02-16 17:41 [PATCH 00/16] media: i2c: GMSL reliability improvements Jacopo Mondi
2021-02-16 17:41 ` [PATCH 01/16] media: i2c: rdacm20: Enable noise immunity Jacopo Mondi
2021-02-17 12:55   ` Kieran Bingham
2021-02-22  0:49     ` Laurent Pinchart
2021-02-22 14:59       ` Jacopo Mondi
2021-02-24 20:35         ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 02/16] media: i2c: rdacm20: Embedded 'serializer' field Jacopo Mondi
2021-02-17 12:56   ` Kieran Bingham
2021-02-22  0:58   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 03/16] media: i2c: rdacm20: Replace goto with a loop Jacopo Mondi
2021-02-17 13:01   ` Kieran Bingham
2021-02-22  1:05     ` Laurent Pinchart
2021-02-22 15:06       ` Jacopo Mondi
2021-02-24 20:27         ` Laurent Pinchart
2021-02-25  8:56           ` Kieran Bingham
2021-02-16 17:41 ` [PATCH 04/16] media: i2c: rdacm20: Report camera module name Jacopo Mondi
2021-02-17 13:02   ` Kieran Bingham
2021-02-22  1:06   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 05/16] media: i2c: rdacm20: Check return values Jacopo Mondi
2021-02-17 13:08   ` Kieran Bingham
2021-02-22  1:09   ` Laurent Pinchart
2021-02-22 15:08     ` Jacopo Mondi
2021-02-16 17:41 ` [PATCH 06/16] media: i2c: rdacm20: Re-work ov10635 reset Jacopo Mondi
2021-02-17 13:22   ` Kieran Bingham
2021-02-22  1:15   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 07/16] media: i2c: rdacm2x: Fix wake up delay Jacopo Mondi
2021-02-17  8:02   ` Geert Uytterhoeven
2021-02-17 13:33   ` Kieran Bingham
2021-02-22  1:18     ` Laurent Pinchart
2021-02-22 15:11       ` Jacopo Mondi
2021-02-24 20:29         ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 08/16] media: i2c: max9286: Adjust parameters indent Jacopo Mondi
2021-02-17 13:36   ` Kieran Bingham
2021-02-22  1:20   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 09/16] media: i2c: rdacm21: Re-work OV10640 initialization Jacopo Mondi
2021-02-17  8:06   ` Geert Uytterhoeven
2021-02-17 13:55   ` Kieran Bingham
2021-02-22  1:27   ` Laurent Pinchart
2021-02-22 15:19     ` Jacopo Mondi
2021-02-24 20:30       ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 10/16] media: i2c: max9286: Rename reverse_channel_mv Jacopo Mondi
2021-02-17  8:07   ` Geert Uytterhoeven
2021-02-18 15:06   ` Kieran Bingham
2021-02-22  1:29   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 11/16] media: i2c: max9286: Cache channel amplitude Jacopo Mondi
2021-02-17  8:08   ` Geert Uytterhoeven
2021-02-18 15:39   ` Kieran Bingham
2021-02-22  1:33   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 12/16] media: i2c: max9286: Define high " Jacopo Mondi
2021-02-18 15:39   ` Kieran Bingham
2021-02-22  1:35   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 13/16] media: i2c: rdacm2x: Implement .init() subdev op Jacopo Mondi
2021-02-17  8:17   ` Geert Uytterhoeven
2021-02-18 16:13   ` Kieran Bingham
2021-02-22  1:52     ` Laurent Pinchart [this message]
2021-02-16 17:41 ` [PATCH 14/16] media: i2c: max9286: Initialize remotes when bound Jacopo Mondi
2021-02-17  8:19   ` Geert Uytterhoeven
2021-02-18 16:00   ` Kieran Bingham
2021-02-22  2:03   ` Laurent Pinchart
2021-02-16 17:41 ` [PATCH 15/16] media: i2c: max9286: Rework comments in .bound() Jacopo Mondi
2021-02-18 16:03   ` Kieran Bingham
2021-02-16 17:41 ` [PATCH 16/16] media: i2c: gmsl: Use 339Kbps I2C bit-rate Jacopo Mondi
2021-02-17  8:19   ` Geert Uytterhoeven
2021-02-18 16:07   ` Kieran Bingham
2021-02-22  2:06     ` Laurent Pinchart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=YDMOaZUi8Q1vWq9j@pendragon.ideasonboard.com \
    --to=laurent.pinchart@ideasonboard.com \
    --cc=geert@linux-m68k.org \
    --cc=jacopo+renesas@jmondi.org \
    --cc=kieran.bingham+renesas@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=mchehab@kernel.org \
    --cc=niklas.soderlund+renesas@ragnatech.se \
    --subject='Re: [PATCH 13/16] media: i2c: rdacm2x: Implement .init() subdev op' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.