[PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, to define the pixel data sampling edge.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
---
V4: New patch split from combined V3
V5: Rebase on recent linux-next
---
 .../bindings/display/bridge/lvds-codec.yaml    | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
index 1faae3e323a4..708de84ac138 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
@@ -79,6 +79,14 @@ properties:
       - port@0
       - port@1
 
+  pclk-sample:
+    description:
+      Data sampling on rising or falling edge.
+    enum:
+      - 0  # Falling edge
+      - 1  # Rising edge
+    default: 0
+
   powerdown-gpios:
     description:
       The GPIO used to control the power down line of this device.
@@ -102,6 +110,16 @@ then:
               properties:
                 data-mapping: false
 
+if:
+  not:
+    properties:
+      compatible:
+        contains:
+          const: lvds-encoder
+then:
+  properties:
+    pclk-sample: false
+
 required:
   - compatible
   - ports
-- 
2.33.0

[PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, and configure bus flags based on this DT property.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
---
V2: - Limit the pixelclk-active to encoders only
    - Update DT binding document
V3: - Determine whether this is encoder from connector, i.e.
      lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS
V4: - Switch to pclk-sample. Note that the value of this is inverted,
      so all the existing users of pixelclk-active using previous
      previous version of this patch must be reworked
V5: Rebase on recent linux-next
---
 drivers/gpu/drm/bridge/lvds-codec.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/gpu/drm/bridge/lvds-codec.c b/drivers/gpu/drm/bridge/lvds-codec.c
index f991842a161f..702ea803a743 100644
--- a/drivers/gpu/drm/bridge/lvds-codec.c
+++ b/drivers/gpu/drm/bridge/lvds-codec.c
@@ -21,6 +21,7 @@ struct lvds_codec {
 	struct device *dev;
 	struct drm_bridge bridge;
 	struct drm_bridge *panel_bridge;
+	struct drm_bridge_timings timings;
 	struct regulator *vcc;
 	struct gpio_desc *powerdown_gpio;
 	u32 connector_type;
@@ -119,6 +120,7 @@ static int lvds_codec_probe(struct platform_device *pdev)
 	struct device_node *bus_node;
 	struct drm_panel *panel;
 	struct lvds_codec *lvds_codec;
+	u32 val;
 	int ret;
 
 	lvds_codec = devm_kzalloc(dev, sizeof(*lvds_codec), GFP_KERNEL);
@@ -187,12 +189,25 @@ static int lvds_codec_probe(struct platform_device *pdev)
 		}
 	}
 
+	/*
+	 * Encoder might sample data on different clock edge than the display,
+	 * for example OnSemi FIN3385 has a dedicated strapping pin to select
+	 * the sampling edge.
+	 */
+	if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
+	    !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
+		lvds_codec->timings.input_bus_flags = val ?
+			DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
+			DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
+	}
+
 	/*
 	 * The panel_bridge bridge is attached to the panel's of_node,
 	 * but we need a bridge attached to our of_node for our user
 	 * to look up.
 	 */
 	lvds_codec->bridge.of_node = dev->of_node;
+	lvds_codec->bridge.timings = &lvds_codec->timings;
 	drm_bridge_add(&lvds_codec->bridge);
 
 	platform_set_drvdata(pdev, lvds_codec);
-- 
2.33.0

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Sam Ravnborg]

Hi Marek,

On Sun, Oct 17, 2021 at 02:12:04AM +0200, Marek Vasut wrote:
> The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
> select input pixel data sampling edge. Add DT property "pclk-sample", not
> the same as the one used by display timings but rather the same as used by
> media, and configure bus flags based on this DT property.

Late to the party here - sorry.

> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: devicetree@vger.kernel.org
> To: dri-devel@lists.freedesktop.org
> ---
> V2: - Limit the pixelclk-active to encoders only
>     - Update DT binding document
> V3: - Determine whether this is encoder from connector, i.e.
>       lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS
> V4: - Switch to pclk-sample. Note that the value of this is inverted,
>       so all the existing users of pixelclk-active using previous
>       previous version of this patch must be reworked
> V5: Rebase on recent linux-next
> ---
>  drivers/gpu/drm/bridge/lvds-codec.c | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/drivers/gpu/drm/bridge/lvds-codec.c b/drivers/gpu/drm/bridge/lvds-codec.c
> index f991842a161f..702ea803a743 100644
> --- a/drivers/gpu/drm/bridge/lvds-codec.c
> +++ b/drivers/gpu/drm/bridge/lvds-codec.c
> @@ -21,6 +21,7 @@ struct lvds_codec {
>  	struct device *dev;
>  	struct drm_bridge bridge;
>  	struct drm_bridge *panel_bridge;
> +	struct drm_bridge_timings timings;
>  	struct regulator *vcc;
>  	struct gpio_desc *powerdown_gpio;
>  	u32 connector_type;
> @@ -119,6 +120,7 @@ static int lvds_codec_probe(struct platform_device *pdev)
>  	struct device_node *bus_node;
>  	struct drm_panel *panel;
>  	struct lvds_codec *lvds_codec;
> +	u32 val;
>  	int ret;
>  
>  	lvds_codec = devm_kzalloc(dev, sizeof(*lvds_codec), GFP_KERNEL);
> @@ -187,12 +189,25 @@ static int lvds_codec_probe(struct platform_device *pdev)
>  		}
>  	}
>  
> +	/*
> +	 * Encoder might sample data on different clock edge than the display,
> +	 * for example OnSemi FIN3385 has a dedicated strapping pin to select
> +	 * the sampling edge.
> +	 */
> +	if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
> +	    !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
> +		lvds_codec->timings.input_bus_flags = val ?
> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
> +	}
> +
>  	/*
>  	 * The panel_bridge bridge is attached to the panel's of_node,
>  	 * but we need a bridge attached to our of_node for our user
>  	 * to look up.
>  	 */
>  	lvds_codec->bridge.of_node = dev->of_node;
> +	lvds_codec->bridge.timings = &lvds_codec->timings;
I do not understand how this will work. The only field that is set is timings.input_bus_flags
but any user will see bridge.timings is set and will think this is all
timing info.

Maybe I just misses something obvious?

	Sam



>  	drm_bridge_add(&lvds_codec->bridge);
>  
>  	platform_set_drvdata(pdev, lvds_codec);
> -- 
> 2.33.0

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 10/17/21 6:49 PM, Sam Ravnborg wrote:

[...]

>> +	/*
>> +	 * Encoder might sample data on different clock edge than the display,
>> +	 * for example OnSemi FIN3385 has a dedicated strapping pin to select
>> +	 * the sampling edge.
>> +	 */
>> +	if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>> +	    !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>> +		lvds_codec->timings.input_bus_flags = val ?
>> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>> +	}
>> +
>>   	/*
>>   	 * The panel_bridge bridge is attached to the panel's of_node,
>>   	 * but we need a bridge attached to our of_node for our user
>>   	 * to look up.
>>   	 */
>>   	lvds_codec->bridge.of_node = dev->of_node;
>> +	lvds_codec->bridge.timings = &lvds_codec->timings;
> I do not understand how this will work. The only field that is set is timings.input_bus_flags
> but any user will see bridge.timings is set and will think this is all
> timing info.
> 
> Maybe I just misses something obvious?

Is there anything else in those timings that should be set ? See
include/drm/drm_bridge.h around line 640

setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, so 
it is 0 or false anyway, i.e. no change.

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Sam Ravnborg]

Hi Marek,

On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
> 
> [...]
> 
> > > +	/*
> > > +	 * Encoder might sample data on different clock edge than the display,
> > > +	 * for example OnSemi FIN3385 has a dedicated strapping pin to select
> > > +	 * the sampling edge.
> > > +	 */
> > > +	if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
> > > +	    !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
> > > +		lvds_codec->timings.input_bus_flags = val ?
> > > +			DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
> > > +			DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
> > > +	}
> > > +
> > >   	/*
> > >   	 * The panel_bridge bridge is attached to the panel's of_node,
> > >   	 * but we need a bridge attached to our of_node for our user
> > >   	 * to look up.
> > >   	 */
> > >   	lvds_codec->bridge.of_node = dev->of_node;
> > > +	lvds_codec->bridge.timings = &lvds_codec->timings;
> > I do not understand how this will work. The only field that is set is timings.input_bus_flags
> > but any user will see bridge.timings is set and will think this is all
> > timing info.
> > 
> > Maybe I just misses something obvious?
> 
> Is there anything else in those timings that should be set ? See
> include/drm/drm_bridge.h around line 640
> 
> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, so it
> is 0 or false anyway, i.e. no change.

Just me being confused with display_timings. Patch looks good.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>

Ping me in a few days to apply it if there is no more feedback.

	Sam

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 10/17/21 7:40 PM, Sam Ravnborg wrote:
> Hi Marek,
> 
> On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
>> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
>>
>> [...]
>>
>>>> +	/*
>>>> +	 * Encoder might sample data on different clock edge than the display,
>>>> +	 * for example OnSemi FIN3385 has a dedicated strapping pin to select
>>>> +	 * the sampling edge.
>>>> +	 */
>>>> +	if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>>>> +	    !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>>>> +		lvds_codec->timings.input_bus_flags = val ?
>>>> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>>>> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>>>> +	}
>>>> +
>>>>    	/*
>>>>    	 * The panel_bridge bridge is attached to the panel's of_node,
>>>>    	 * but we need a bridge attached to our of_node for our user
>>>>    	 * to look up.
>>>>    	 */
>>>>    	lvds_codec->bridge.of_node = dev->of_node;
>>>> +	lvds_codec->bridge.timings = &lvds_codec->timings;
>>> I do not understand how this will work. The only field that is set is timings.input_bus_flags
>>> but any user will see bridge.timings is set and will think this is all
>>> timing info.
>>>
>>> Maybe I just misses something obvious?
>>
>> Is there anything else in those timings that should be set ? See
>> include/drm/drm_bridge.h around line 640
>>
>> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, so it
>> is 0 or false anyway, i.e. no change.
> 
> Just me being confused with display_timings. Patch looks good.
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
> 
> Ping me in a few days to apply it if there is no more feedback.

ACK

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Rob Herring]

On Sun, 17 Oct 2021 02:12:03 +0200, Marek Vasut wrote:
> The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
> select input pixel data sampling edge. Add DT property "pclk-sample", not
> the same as the one used by display timings but rather the same as used by
> media, to define the pixel data sampling edge.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: devicetree@vger.kernel.org
> To: dri-devel@lists.freedesktop.org
> ---
> V4: New patch split from combined V3
> V5: Rebase on recent linux-next
> ---
>  .../bindings/display/bridge/lvds-codec.yaml    | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Laurent Pinchart]

Hi Marek,

Thank you for the patch.

On Sun, Oct 17, 2021 at 02:12:03AM +0200, Marek Vasut wrote:
> The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
> select input pixel data sampling edge. Add DT property "pclk-sample", not
> the same as the one used by display timings but rather the same as used by
> media, to define the pixel data sampling edge.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: devicetree@vger.kernel.org
> To: dri-devel@lists.freedesktop.org
> ---
> V4: New patch split from combined V3
> V5: Rebase on recent linux-next
> ---
>  .../bindings/display/bridge/lvds-codec.yaml    | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> index 1faae3e323a4..708de84ac138 100644
> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> @@ -79,6 +79,14 @@ properties:
>        - port@0
>        - port@1
>  
> +  pclk-sample:
> +    description:
> +      Data sampling on rising or falling edge.
> +    enum:
> +      - 0  # Falling edge
> +      - 1  # Rising edge
> +    default: 0
> +

Shouldn't this be moved to the endpoint, the same way data-mapping is
defined as an endpoint property ?

>    powerdown-gpios:
>      description:
>        The GPIO used to control the power down line of this device.
> @@ -102,6 +110,16 @@ then:
>                properties:
>                  data-mapping: false
>  
> +if:
> +  not:
> +    properties:
> +      compatible:
> +        contains:
> +          const: lvds-encoder
> +then:
> +  properties:
> +    pclk-sample: false
> +
>  required:
>    - compatible
>    - ports

-- 
Regards,

Laurent Pinchart

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

On 10/18/21 8:08 PM, Laurent Pinchart wrote:

[...]

>> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>> index 1faae3e323a4..708de84ac138 100644
>> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>> @@ -79,6 +79,14 @@ properties:
>>         - port@0
>>         - port@1
>>   
>> +  pclk-sample:
>> +    description:
>> +      Data sampling on rising or falling edge.
>> +    enum:
>> +      - 0  # Falling edge
>> +      - 1  # Rising edge
>> +    default: 0
>> +
> 
> Shouldn't this be moved to the endpoint, the same way data-mapping is
> defined as an endpoint property ?

The strapping is a chip property, not port property, so no.

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Laurent Pinchart]

Hi Marek,

On Mon, Oct 18, 2021 at 09:47:13PM +0200, Marek Vasut wrote:
> On 10/18/21 8:08 PM, Laurent Pinchart wrote:
> 
> [...]
> 
> >> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >> index 1faae3e323a4..708de84ac138 100644
> >> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >> @@ -79,6 +79,14 @@ properties:
> >>         - port@0
> >>         - port@1
> >>   
> >> +  pclk-sample:
> >> +    description:
> >> +      Data sampling on rising or falling edge.
> >> +    enum:
> >> +      - 0  # Falling edge
> >> +      - 1  # Rising edge
> >> +    default: 0
> >> +
> > 
> > Shouldn't this be moved to the endpoint, the same way data-mapping is
> > defined as an endpoint property ?
> 
> The strapping is a chip property, not port property, so no.

For this particular chip that's true. I'm still not convinced overall.
For some cases it could be a per-port property, and moving it there for
lvds-codec too could allow implementing helpers to parse DT properties,
without much drawback for this particular use case as far as I can see.
It's hard to predict the future with certainty of course, so I won't
insist.

-- 
Regards,

Laurent Pinchart

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

On 10/18/21 9:57 PM, Laurent Pinchart wrote:

Hi,

>>>> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>> index 1faae3e323a4..708de84ac138 100644
>>>> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>> @@ -79,6 +79,14 @@ properties:
>>>>          - port@0
>>>>          - port@1
>>>>    
>>>> +  pclk-sample:
>>>> +    description:
>>>> +      Data sampling on rising or falling edge.
>>>> +    enum:
>>>> +      - 0  # Falling edge
>>>> +      - 1  # Rising edge
>>>> +    default: 0
>>>> +
>>>
>>> Shouldn't this be moved to the endpoint, the same way data-mapping is
>>> defined as an endpoint property ?
>>
>> The strapping is a chip property, not port property, so no.
> 
> For this particular chip that's true. I'm still not convinced overall.
> For some cases it could be a per-port property

Can you be more specific about "some cases" ?

> , and moving it there for
> lvds-codec too could allow implementing helpers to parse DT properties,
> without much drawback for this particular use case as far as I can see.
> It's hard to predict the future with certainty of course, so I won't
> insist.

The DT bindings and the OS drivers are separate thing, we really 
shouldn't start bending DT bindings so that they would fit nicely with a 
specific OS driver model.

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Laurent Pinchart]

Hi Marek,

On Tue, Oct 19, 2021 at 12:18:11AM +0200, Marek Vasut wrote:
> On 10/18/21 9:57 PM, Laurent Pinchart wrote:
> 
> Hi,
> 
> >>>> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >>>> index 1faae3e323a4..708de84ac138 100644
> >>>> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >>>> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >>>> @@ -79,6 +79,14 @@ properties:
> >>>>          - port@0
> >>>>          - port@1
> >>>>    
> >>>> +  pclk-sample:
> >>>> +    description:
> >>>> +      Data sampling on rising or falling edge.
> >>>> +    enum:
> >>>> +      - 0  # Falling edge
> >>>> +      - 1  # Rising edge
> >>>> +    default: 0
> >>>> +
> >>>
> >>> Shouldn't this be moved to the endpoint, the same way data-mapping is
> >>> defined as an endpoint property ?
> >>
> >> The strapping is a chip property, not port property, so no.
> > 
> > For this particular chip that's true. I'm still not convinced overall.
> > For some cases it could be a per-port property
> 
> Can you be more specific about "some cases" ?

I'm thinking about bridges that could have multiple parallel inputs.

> > , and moving it there for
> > lvds-codec too could allow implementing helpers to parse DT properties,
> > without much drawback for this particular use case as far as I can see.
> > It's hard to predict the future with certainty of course, so I won't
> > insist.
> 
> The DT bindings and the OS drivers are separate thing, we really 
> shouldn't start bending DT bindings so that they would fit nicely with a 
> specific OS driver model.

DT bindings are not holy beings that live in a mythical heaven way above
the mere mortal drivers, they would be useless without implementations.
It's not about bending them, which I regularly push against during
review, but about structuring them in a way that facilitates
implementations when all other things are equal.

As I said, despite wondering whether or not it would be better to move
the property to the endpoint (and that was a genuine open question), I
won't insist in this case.

-- 
Regards,

Laurent Pinchart

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

On 10/19/21 8:49 AM, Laurent Pinchart wrote:
> Hi Marek,

Hi,

>>>>>> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>>>> index 1faae3e323a4..708de84ac138 100644
>>>>>> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>>>> @@ -79,6 +79,14 @@ properties:
>>>>>>           - port@0
>>>>>>           - port@1
>>>>>>     
>>>>>> +  pclk-sample:
>>>>>> +    description:
>>>>>> +      Data sampling on rising or falling edge.
>>>>>> +    enum:
>>>>>> +      - 0  # Falling edge
>>>>>> +      - 1  # Rising edge
>>>>>> +    default: 0
>>>>>> +
>>>>>
>>>>> Shouldn't this be moved to the endpoint, the same way data-mapping is
>>>>> defined as an endpoint property ?
>>>>
>>>> The strapping is a chip property, not port property, so no.
>>>
>>> For this particular chip that's true. I'm still not convinced overall.
>>> For some cases it could be a per-port property
>>
>> Can you be more specific about "some cases" ?
> 
> I'm thinking about bridges that could have multiple parallel inputs.

Can you draft an example how such a binding would look like within the 
confines of this lvds-codec.yaml ?

I also have to wonder how such a hypothetical device would work, would 
it serialize two parallel bussed into single LVDS one ?

>>> , and moving it there for
>>> lvds-codec too could allow implementing helpers to parse DT properties,
>>> without much drawback for this particular use case as far as I can see.
>>> It's hard to predict the future with certainty of course, so I won't
>>> insist.
>>
>> The DT bindings and the OS drivers are separate thing, we really
>> shouldn't start bending DT bindings so that they would fit nicely with a
>> specific OS driver model.
> 
> DT bindings are not holy beings that live in a mythical heaven way above
> the mere mortal drivers, they would be useless without implementations.
> It's not about bending them, which I regularly push against during
> review, but about structuring them in a way that facilitates
> implementations when all other things are equal.

Note that the pclk-sample isn't a property of the input, but of the 
chip, I don't think it is a good idea to say they are equal and conflate 
them like so.

> As I said, despite wondering whether or not it would be better to move
> the property to the endpoint (and that was a genuine open question), I
> won't insist in this case.

[...]

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 10/17/21 7:40 PM, Sam Ravnborg wrote:
> Hi Marek,

Hi,

> On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
>> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
>>
>> [...]
>>
>>>> +	/*
>>>> +	 * Encoder might sample data on different clock edge than the display,
>>>> +	 * for example OnSemi FIN3385 has a dedicated strapping pin to select
>>>> +	 * the sampling edge.
>>>> +	 */
>>>> +	if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>>>> +	    !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>>>> +		lvds_codec->timings.input_bus_flags = val ?
>>>> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>>>> +			DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>>>> +	}
>>>> +
>>>>    	/*
>>>>    	 * The panel_bridge bridge is attached to the panel's of_node,
>>>>    	 * but we need a bridge attached to our of_node for our user
>>>>    	 * to look up.
>>>>    	 */
>>>>    	lvds_codec->bridge.of_node = dev->of_node;
>>>> +	lvds_codec->bridge.timings = &lvds_codec->timings;
>>> I do not understand how this will work. The only field that is set is timings.input_bus_flags
>>> but any user will see bridge.timings is set and will think this is all
>>> timing info.
>>>
>>> Maybe I just misses something obvious?
>>
>> Is there anything else in those timings that should be set ? See
>> include/drm/drm_bridge.h around line 640
>>
>> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, so it
>> is 0 or false anyway, i.e. no change.
> 
> Just me being confused with display_timings. Patch looks good.
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
> 
> Ping me in a few days to apply it if there is no more feedback.

Ping I guess ... Laurent ?

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Laurent Pinchart]

On Tue, Oct 19, 2021 at 04:39:05PM +0200, Marek Vasut wrote:
> On 10/19/21 8:49 AM, Laurent Pinchart wrote:
> > Hi Marek,
> 
> Hi,
> 
> >>>>>> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >>>>>> index 1faae3e323a4..708de84ac138 100644
> >>>>>> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >>>>>> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
> >>>>>> @@ -79,6 +79,14 @@ properties:
> >>>>>>           - port@0
> >>>>>>           - port@1
> >>>>>>     
> >>>>>> +  pclk-sample:
> >>>>>> +    description:
> >>>>>> +      Data sampling on rising or falling edge.
> >>>>>> +    enum:
> >>>>>> +      - 0  # Falling edge
> >>>>>> +      - 1  # Rising edge
> >>>>>> +    default: 0
> >>>>>> +
> >>>>>
> >>>>> Shouldn't this be moved to the endpoint, the same way data-mapping is
> >>>>> defined as an endpoint property ?
> >>>>
> >>>> The strapping is a chip property, not port property, so no.
> >>>
> >>> For this particular chip that's true. I'm still not convinced overall.
> >>> For some cases it could be a per-port property
> >>
> >> Can you be more specific about "some cases" ?
> > 
> > I'm thinking about bridges that could have multiple parallel inputs.
> 
> Can you draft an example how such a binding would look like within the 
> confines of this lvds-codec.yaml ?
> 
> I also have to wonder how such a hypothetical device would work, would 
> it serialize two parallel bussed into single LVDS one ?

Such a device would require custom bindings I think, as lvds-codec is
limited to a single input and a single output. thine,thc63lvd1024.yaml
is an example of such a device.

> >>> , and moving it there for
> >>> lvds-codec too could allow implementing helpers to parse DT properties,
> >>> without much drawback for this particular use case as far as I can see.
> >>> It's hard to predict the future with certainty of course, so I won't
> >>> insist.
> >>
> >> The DT bindings and the OS drivers are separate thing, we really
> >> shouldn't start bending DT bindings so that they would fit nicely with a
> >> specific OS driver model.
> > 
> > DT bindings are not holy beings that live in a mythical heaven way above
> > the mere mortal drivers, they would be useless without implementations.
> > It's not about bending them, which I regularly push against during
> > review, but about structuring them in a way that facilitates
> > implementations when all other things are equal.
> 
> Note that the pclk-sample isn't a property of the input, but of the 
> chip, I don't think it is a good idea to say they are equal and conflate 
> them like so.

With a chip that has a single input, that's always the case :-)

Anyway, I don't mind a chip-level property for this binding as we're
limited to a single port. If other devices need to specify this at the
port level, I'm sure we'll be able to cope with the lack of uniformity.

> > As I said, despite wondering whether or not it would be better to move
> > the property to the endpoint (and that was a genuine open question), I
> > won't insist in this case.
> 
> [...]

-- 
Regards,

Laurent Pinchart

Re: [PATCH v5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

On 10/27/21 1:43 AM, Laurent Pinchart wrote:

[...]

>>>>>>>> diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>>>>>> index 1faae3e323a4..708de84ac138 100644
>>>>>>>> --- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>>>>>> +++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
>>>>>>>> @@ -79,6 +79,14 @@ properties:
>>>>>>>>            - port@0
>>>>>>>>            - port@1
>>>>>>>>      
>>>>>>>> +  pclk-sample:
>>>>>>>> +    description:
>>>>>>>> +      Data sampling on rising or falling edge.
>>>>>>>> +    enum:
>>>>>>>> +      - 0  # Falling edge
>>>>>>>> +      - 1  # Rising edge
>>>>>>>> +    default: 0
>>>>>>>> +
>>>>>>>
>>>>>>> Shouldn't this be moved to the endpoint, the same way data-mapping is
>>>>>>> defined as an endpoint property ?
>>>>>>
>>>>>> The strapping is a chip property, not port property, so no.
>>>>>
>>>>> For this particular chip that's true. I'm still not convinced overall.
>>>>> For some cases it could be a per-port property
>>>>
>>>> Can you be more specific about "some cases" ?
>>>
>>> I'm thinking about bridges that could have multiple parallel inputs.
>>
>> Can you draft an example how such a binding would look like within the
>> confines of this lvds-codec.yaml ?
>>
>> I also have to wonder how such a hypothetical device would work, would
>> it serialize two parallel bussed into single LVDS one ?
> 
> Such a device would require custom bindings I think, as lvds-codec is
> limited to a single input and a single output. thine,thc63lvd1024.yaml
> is an example of such a device.

It seems THC63LVD1024 is LVDS->to->Parallel DPI, so pclk-sample does not 
seem applicable there either.

[...]

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 10/24/21 1:04 AM, Marek Vasut wrote:
> On 10/17/21 7:40 PM, Sam Ravnborg wrote:
>> Hi Marek,
> 
> Hi,
> 
>> On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
>>> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
>>>
>>> [...]
>>>
>>>>> +    /*
>>>>> +     * Encoder might sample data on different clock edge than the 
>>>>> display,
>>>>> +     * for example OnSemi FIN3385 has a dedicated strapping pin to 
>>>>> select
>>>>> +     * the sampling edge.
>>>>> +     */
>>>>> +    if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>>>>> +        !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>>>>> +        lvds_codec->timings.input_bus_flags = val ?
>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>>>>> +    }
>>>>> +
>>>>>        /*
>>>>>         * The panel_bridge bridge is attached to the panel's of_node,
>>>>>         * but we need a bridge attached to our of_node for our user
>>>>>         * to look up.
>>>>>         */
>>>>>        lvds_codec->bridge.of_node = dev->of_node;
>>>>> +    lvds_codec->bridge.timings = &lvds_codec->timings;
>>>> I do not understand how this will work. The only field that is set 
>>>> is timings.input_bus_flags
>>>> but any user will see bridge.timings is set and will think this is all
>>>> timing info.
>>>>
>>>> Maybe I just misses something obvious?
>>>
>>> Is there anything else in those timings that should be set ? See
>>> include/drm/drm_bridge.h around line 640
>>>
>>> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, 
>>> so it
>>> is 0 or false anyway, i.e. no change.
>>
>> Just me being confused with display_timings. Patch looks good.
>> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
>>
>> Ping me in a few days to apply it if there is no more feedback.
> 
> Ping I guess ... Laurent ?

Ping one more time ?

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 10/24/21 1:04 AM, Marek Vasut wrote:
> On 10/17/21 7:40 PM, Sam Ravnborg wrote:
>> Hi Marek,
> 
> Hi,
> 
>> On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
>>> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
>>>
>>> [...]
>>>
>>>>> +    /*
>>>>> +     * Encoder might sample data on different clock edge than the 
>>>>> display,
>>>>> +     * for example OnSemi FIN3385 has a dedicated strapping pin to 
>>>>> select
>>>>> +     * the sampling edge.
>>>>> +     */
>>>>> +    if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>>>>> +        !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>>>>> +        lvds_codec->timings.input_bus_flags = val ?
>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>>>>> +    }
>>>>> +
>>>>>        /*
>>>>>         * The panel_bridge bridge is attached to the panel's of_node,
>>>>>         * but we need a bridge attached to our of_node for our user
>>>>>         * to look up.
>>>>>         */
>>>>>        lvds_codec->bridge.of_node = dev->of_node;
>>>>> +    lvds_codec->bridge.timings = &lvds_codec->timings;
>>>> I do not understand how this will work. The only field that is set 
>>>> is timings.input_bus_flags
>>>> but any user will see bridge.timings is set and will think this is all
>>>> timing info.
>>>>
>>>> Maybe I just misses something obvious?
>>>
>>> Is there anything else in those timings that should be set ? See
>>> include/drm/drm_bridge.h around line 640
>>>
>>> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, 
>>> so it
>>> is 0 or false anyway, i.e. no change.
>>
>> Just me being confused with display_timings. Patch looks good.
>> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
>>
>> Ping me in a few days to apply it if there is no more feedback.
> 
> Ping I guess ... Laurent ?

Ping one more time ?

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 11/24/21 04:02, Marek Vasut wrote:
> On 10/24/21 1:04 AM, Marek Vasut wrote:
>> On 10/17/21 7:40 PM, Sam Ravnborg wrote:
>>> Hi Marek,
>>
>> Hi,
>>
>>> On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
>>>> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
>>>>
>>>> [...]
>>>>
>>>>>> +    /*
>>>>>> +     * Encoder might sample data on different clock edge than the 
>>>>>> display,
>>>>>> +     * for example OnSemi FIN3385 has a dedicated strapping pin 
>>>>>> to select
>>>>>> +     * the sampling edge.
>>>>>> +     */
>>>>>> +    if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>>>>>> +        !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>>>>>> +        lvds_codec->timings.input_bus_flags = val ?
>>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>>>>>> +    }
>>>>>> +
>>>>>>        /*
>>>>>>         * The panel_bridge bridge is attached to the panel's of_node,
>>>>>>         * but we need a bridge attached to our of_node for our user
>>>>>>         * to look up.
>>>>>>         */
>>>>>>        lvds_codec->bridge.of_node = dev->of_node;
>>>>>> +    lvds_codec->bridge.timings = &lvds_codec->timings;
>>>>> I do not understand how this will work. The only field that is set 
>>>>> is timings.input_bus_flags
>>>>> but any user will see bridge.timings is set and will think this is all
>>>>> timing info.
>>>>>
>>>>> Maybe I just misses something obvious?
>>>>
>>>> Is there anything else in those timings that should be set ? See
>>>> include/drm/drm_bridge.h around line 640
>>>>
>>>> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, 
>>>> so it
>>>> is 0 or false anyway, i.e. no change.
>>>
>>> Just me being confused with display_timings. Patch looks good.
>>> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
>>>
>>> Ping me in a few days to apply it if there is no more feedback.
>>
>> Ping I guess ... Laurent ?
> 
> Ping one more time ?

Ping yet again ?

Re: [PATCH v5 2/2] drm/bridge: lvds-codec: Add support for pixel data sampling edge select

[Marek Vasut]

On 11/24/21 04:02, Marek Vasut wrote:
> On 10/24/21 1:04 AM, Marek Vasut wrote:
>> On 10/17/21 7:40 PM, Sam Ravnborg wrote:
>>> Hi Marek,
>>
>> Hi,
>>
>>> On Sun, Oct 17, 2021 at 07:29:51PM +0200, Marek Vasut wrote:
>>>> On 10/17/21 6:49 PM, Sam Ravnborg wrote:
>>>>
>>>> [...]
>>>>
>>>>>> +    /*
>>>>>> +     * Encoder might sample data on different clock edge than the 
>>>>>> display,
>>>>>> +     * for example OnSemi FIN3385 has a dedicated strapping pin 
>>>>>> to select
>>>>>> +     * the sampling edge.
>>>>>> +     */
>>>>>> +    if (lvds_codec->connector_type == DRM_MODE_CONNECTOR_LVDS &&
>>>>>> +        !of_property_read_u32(dev->of_node, "pclk-sample", &val)) {
>>>>>> +        lvds_codec->timings.input_bus_flags = val ?
>>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE :
>>>>>> +            DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
>>>>>> +    }
>>>>>> +
>>>>>>        /*
>>>>>>         * The panel_bridge bridge is attached to the panel's of_node,
>>>>>>         * but we need a bridge attached to our of_node for our user
>>>>>>         * to look up.
>>>>>>         */
>>>>>>        lvds_codec->bridge.of_node = dev->of_node;
>>>>>> +    lvds_codec->bridge.timings = &lvds_codec->timings;
>>>>> I do not understand how this will work. The only field that is set 
>>>>> is timings.input_bus_flags
>>>>> but any user will see bridge.timings is set and will think this is all
>>>>> timing info.
>>>>>
>>>>> Maybe I just misses something obvious?
>>>>
>>>> Is there anything else in those timings that should be set ? See
>>>> include/drm/drm_bridge.h around line 640
>>>>
>>>> setup_time_ps/hold_time_ps/dual_link isn't supported by this driver, 
>>>> so it
>>>> is 0 or false anyway, i.e. no change.
>>>
>>> Just me being confused with display_timings. Patch looks good.
>>> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
>>>
>>> Ping me in a few days to apply it if there is no more feedback.
>>
>> Ping I guess ... Laurent ?
> 
> Ping one more time ?

Ping yet again ?

Re: [PATCH V5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Rob Herring]

On Wed, 02 Jun 2021 22:36:07 +0200, Marek Vasut wrote:
> The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
> select input pixel data sampling edge. Add DT property "pclk-sample", not
> the same as the one used by display timings but rather the same as used by
> media, to define the pixel data sampling edge.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Antonio Borneo <antonio.borneo@st.com>
> Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
> Cc: Biju Das <biju.das.jz@bp.renesas.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Philippe Cornu <philippe.cornu@st.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Vincent Abriou <vincent.abriou@st.com>
> Cc: Yannick Fertre <yannick.fertre@st.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: dri-devel@lists.freedesktop.org
> ---
> V4: New patch split from combined V3
> V5: Move the pclk-sample into port@0 endpoint
> ---
>  .../bindings/display/bridge/lvds-codec.yaml   | 24 +++++++++++++++++++
>  1 file changed, 24 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH V5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Rob Herring]

On Wed, 02 Jun 2021 22:36:07 +0200, Marek Vasut wrote:
> The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
> select input pixel data sampling edge. Add DT property "pclk-sample", not
> the same as the one used by display timings but rather the same as used by
> media, to define the pixel data sampling edge.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Antonio Borneo <antonio.borneo@st.com>
> Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
> Cc: Biju Das <biju.das.jz@bp.renesas.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Philippe Cornu <philippe.cornu@st.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Vincent Abriou <vincent.abriou@st.com>
> Cc: Yannick Fertre <yannick.fertre@st.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: dri-devel@lists.freedesktop.org
> ---
> V4: New patch split from combined V3
> V5: Move the pclk-sample into port@0 endpoint
> ---
>  .../bindings/display/bridge/lvds-codec.yaml   | 24 +++++++++++++++++++
>  1 file changed, 24 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Rob Herring]

On Wed, 02 Jun 2021 22:36:07 +0200, Marek Vasut wrote:
> The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
> select input pixel data sampling edge. Add DT property "pclk-sample", not
> the same as the one used by display timings but rather the same as used by
> media, to define the pixel data sampling edge.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Alexandre Torgue <alexandre.torgue@st.com>
> Cc: Andrzej Hajda <a.hajda@samsung.com>
> Cc: Antonio Borneo <antonio.borneo@st.com>
> Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
> Cc: Biju Das <biju.das.jz@bp.renesas.com>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
> Cc: Philippe Cornu <philippe.cornu@st.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Sam Ravnborg <sam@ravnborg.org>
> Cc: Vincent Abriou <vincent.abriou@st.com>
> Cc: Yannick Fertre <yannick.fertre@st.com>
> Cc: devicetree@vger.kernel.org
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-stm32@st-md-mailman.stormreply.com
> To: dri-devel@lists.freedesktop.org
> ---
> V4: New patch split from combined V3
> V5: Move the pclk-sample into port@0 endpoint
> ---
>  .../bindings/display/bridge/lvds-codec.yaml   | 24 +++++++++++++++++++
>  1 file changed, 24 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH V5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, to define the pixel data sampling edge.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: dri-devel@lists.freedesktop.org
---
V4: New patch split from combined V3
V5: Move the pclk-sample into port@0 endpoint
---
 .../bindings/display/bridge/lvds-codec.yaml   | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
index 304a1367faaa7..cacafa61e3f52 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
@@ -54,6 +54,14 @@ properties:
           For LVDS encoders, port 0 is the parallel input
           For LVDS decoders, port 0 is the LVDS input
 
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              pclk-sample: true
+
       port@1:
         $ref: /schemas/graph.yaml#/properties/port
         description: |
@@ -71,6 +79,22 @@ properties:
 
   power-supply: true
 
+if:
+  not:
+    properties:
+      compatible:
+        contains:
+          const: lvds-encoder
+then:
+  properties:
+    ports:
+      properties:
+        port@0:
+          properties:
+            endpoint:
+              properties:
+                pclk-sample: false
+
 required:
   - compatible
   - ports
-- 
2.30.2

[PATCH V5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, to define the pixel data sampling edge.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: dri-devel@lists.freedesktop.org
---
V4: New patch split from combined V3
V5: Move the pclk-sample into port@0 endpoint
---
 .../bindings/display/bridge/lvds-codec.yaml   | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
index 304a1367faaa7..cacafa61e3f52 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
@@ -54,6 +54,14 @@ properties:
           For LVDS encoders, port 0 is the parallel input
           For LVDS decoders, port 0 is the LVDS input
 
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              pclk-sample: true
+
       port@1:
         $ref: /schemas/graph.yaml#/properties/port
         description: |
@@ -71,6 +79,22 @@ properties:
 
   power-supply: true
 
+if:
+  not:
+    properties:
+      compatible:
+        contains:
+          const: lvds-encoder
+then:
+  properties:
+    ports:
+      properties:
+        port@0:
+          properties:
+            endpoint:
+              properties:
+                pclk-sample: false
+
 required:
   - compatible
   - ports
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V5 1/2] dt-bindings: display: bridge: lvds-codec: Document pixel data sampling edge select

[Marek Vasut]

The OnSemi FIN3385 Parallel-to-LVDS encoder has a dedicated input line to
select input pixel data sampling edge. Add DT property "pclk-sample", not
the same as the one used by display timings but rather the same as used by
media, to define the pixel data sampling edge.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: dri-devel@lists.freedesktop.org
---
V4: New patch split from combined V3
V5: Move the pclk-sample into port@0 endpoint
---
 .../bindings/display/bridge/lvds-codec.yaml   | 24 +++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
index 304a1367faaa7..cacafa61e3f52 100644
--- a/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/lvds-codec.yaml
@@ -54,6 +54,14 @@ properties:
           For LVDS encoders, port 0 is the parallel input
           For LVDS decoders, port 0 is the LVDS input
 
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              pclk-sample: true
+
       port@1:
         $ref: /schemas/graph.yaml#/properties/port
         description: |
@@ -71,6 +79,22 @@ properties:
 
   power-supply: true
 
+if:
+  not:
+    properties:
+      compatible:
+        contains:
+          const: lvds-encoder
+then:
+  properties:
+    ports:
+      properties:
+        port@0:
+          properties:
+            endpoint:
+              properties:
+                pclk-sample: false
+
 required:
   - compatible
   - ports
-- 
2.30.2