Re: [PATCH v2 2/2] board: mntre: imx8mq: Add MNT Reform 2 board support

[Patrick Wildt <patrick@blueri.se>]

On Thu, Nov 11, 2021 at 12:21:26PM +0100, Patrick Wildt wrote:
> On Wed, Nov 10, 2021 at 02:26:54PM -0800, Vagrant Cascadian wrote:
> > On 2021-09-02, Patrick Wildt wrote:
> > > The MNT Reform 2 is a modular DIY laptop.  In its initial version it
> > > is based on the BoundaryDevices i.MX8MQ SoM.  Some parts have been
> > > lifted from BoundaryDevices official U-Boot downstream project.
> > 
> > Thanks for working on this!
> > 
> > I'm struggling a bit getting it to actually boot; how is this supposed
> > to be installed to the device?
> > 
> > I've built with the two applied patches on a patched v2021.10, copying
> > various firmware parts from:
> > 
> >   https://source.mnt.re/reform/reform-boundary-uboot/-/blob/master/bl31-iMX8MQ.bin
> >   https://source.mnt.re/reform/reform-boundary-uboot/-/blob/master/lpddr4_pmu_train_1d_dmem.bin
> >   https://source.mnt.re/reform/reform-boundary-uboot/-/blob/master/lpddr4_pmu_train_1d_imem.bin
> >   https://source.mnt.re/reform/reform-boundary-uboot/-/blob/master/lpddr4_pmu_train_2d_dmem.bin
> >   https://source.mnt.re/reform/reform-boundary-uboot/-/blob/master/lpddr4_pmu_train_2d_imem.bin
> > 
> >   export BL31=bl31-iMX8MQ.bin
> > 
> >   make imx8mq_reform2_defconfig
> >   make
> >   make flash.bin
> > 
> > Then grepping various other README's from imx8mq devices, I tried two
> > different processes:
> > 
> >   dd if=flash.bin of=/dev/sd[x] bs=1K seek=33
> 
> You only need to dd flash.bin, the command looks fine.

Correction: With Peng's current Binman patchset you need both.  But I
think that is not correct, because for i.MX8MM Binman was changed back
to generate a single image.  The following patch includes that change,
so you only need to dd flash.bin.

> > and:
> > 
> >   dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 conv=sync
> >   dd if=u-boot.itb of=/dev/sd[x] bs=1024 seek=384 conv=sync
> > 
> > Both simply hanging with:
> > 
> >   U-Boot SPL 2021.10 (Jan 01 1970 - 00:00:01 +0000)
> 
> There have been a few changes in U-Boot since I sent my patchset, it's
> possible the diff by itself might not be enough.
> 
> I will send out a new patchset soon, but the move to Binman doesn't work
> for me yet.  It's weird, because I don't see a diff to other i.MX8MQ
> platforms, so I'm still debugging that.  Maybe the other i.MX8MQ boards
> don't work with Binman either?
> 
> Keep note that the build procedure (how to supply bl31) changes once
> Binman is used.

I have fixed the issue.  My changes depend on Peng's patchset to change
i.MX8MQ to Binman, so I will re-issue a v3 of the patchset as soon as
that is done (to not interfere any further with his patchset).

'Attached' you'll find a complete diff you can apply to origin/master,
which includes some of Peng's changes.  Let me know how it goes for you.

Patrick

> > Is the flash.bin step unecessary? I see DDR timing code in the patch
> > series; are corresponding lpddr4*.bin no longer necessary?
> 
> The flash.bin has all bits: U-Boot, U-Boot SPL, lpddr4*.bin and bl31.bin
> 
> lpddr4*.bin is the firmware for the DDR controller.  So you need the
> timing information *and* the firmware.
> 
> > I also tried building with an old version of arm-trusted-firmware
> > (v2.2), as that was the most recent upstream version that successfully
> > built. This seems to be a fork of ATF that has support for iMX8MQ, but
> > it is unclear which branch/tag/etc. should be used with the mnt/reform:
> > 
> >   https://source.codeaurora.org/external/imx/imx-atf
> 
> Not sure right now, but I think I was using the one that's build on
> OpenBSD-current, which seems to be arm-trusted-firmware 2.5.  I'll
> check it.
> 
> > It would be nice to include a board README in the next patch revision to
> > spell out some of the details of exactly which other projects and
> > versions/comments/branches are expected to work with MNT Reform2.
> > 
> 
> This is nothing specific to the MNT Reform2.  It's the same for all
> i.MX8MQ boards.  ATF+DDR+U-Boot have to work together, and it doesn't
> matter which board it is.  Hence I don't believe providing that kind
> information in a Reform-specific README makes sense.
> 
> Patrick
> 
> > 
> > I would be nice if you could CC me on future patch series revisions to
> > be able to test. Thanks!
> > 
> > 
> > live well,
> >   vagrant

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index cc34da7bd8..6c14e9328e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -904,6 +904,7 @@ dtb-$(CONFIG_ARCH_IMX8M) += \
 	imx8mq-evk.dtb \
 	imx8mm-beacon-kit.dtb \
 	imx8mn-beacon-kit.dtb \
+	imx8mq-mnt-reform2.dtb \
 	imx8mq-phanbell.dtb \
 	imx8mp-evk.dtb \
 	imx8mp-phyboard-pollux-rdk.dtb \
diff --git a/arch/arm/dts/imx8mq-mnt-reform2-u-boot.dtsi b/arch/arm/dts/imx8mq-mnt-reform2-u-boot.dtsi
new file mode 100644
index 0000000000..c38c698794
--- /dev/null
+++ b/arch/arm/dts/imx8mq-mnt-reform2-u-boot.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "imx8mq-u-boot.dtsi"
+
+&usdhc1 {
+	mmc-hs400-1_8v;
+};
+
+&usdhc2 {
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+};
diff --git a/arch/arm/dts/imx8mq-mnt-reform2.dts b/arch/arm/dts/imx8mq-mnt-reform2.dts
new file mode 100644
index 0000000000..4f2db6197b
--- /dev/null
+++ b/arch/arm/dts/imx8mq-mnt-reform2.dts
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/*
+ * Copyright 2019-2021 MNT Research GmbH
+ * Copyright 2021 Lucas Stach <dev@lynxeye.de>
+ */
+
+/dts-v1/;
+
+#include "imx8mq-nitrogen-som.dtsi"
+
+/ {
+	model = "MNT Reform 2";
+	compatible = "mntre,reform2", "boundary,imx8mq-nitrogen8m-som", "fsl,imx8mq";
+
+	pcie1_refclk: clock-pcie1-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_main_5v: regulator-main-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_main_3v3: regulator-main-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_main_usb: regulator-main-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_main_5v>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-wm8960";
+		audio-cpu = <&sai2>;
+		audio-codec = <&wm8960>;
+		audio-routing =
+			"Headphone Jack", "HP_L",
+			"Headphone Jack", "HP_R",
+			"Ext Spk", "SPK_LP",
+			"Ext Spk", "SPK_LN",
+			"Ext Spk", "SPK_RP",
+			"Ext Spk", "SPK_RN",
+			"LINPUT1", "Mic Jack",
+			"Mic Jack", "MICB",
+			"LINPUT2", "Line In Jack",
+			"RINPUT2", "Line In Jack";
+		model = "wm8960-audio";
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	wm8960: codec@1a {
+		compatible = "wlf,wm8960";
+		reg = <0x1a>;
+		clocks = <&clk IMX8MQ_CLK_SAI2_ROOT>;
+		clock-names = "mclk";
+		#sound-dai-cells = <0>;
+	};
+
+	rtc@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+};
+
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie1>;
+	reset-gpio = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE2_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE2_PHY>,
+		 <&pcie1_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	status = "okay";
+};
+
+&reg_1p8v {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_snvs {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_arm_dram {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_dram_1p1v {
+	vin-supply = <&reg_main_5v>;
+};
+
+&reg_soc_gpu_vpu {
+	vin-supply = <&reg_main_5v>;
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clk IMX8MQ_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+	assigned-clock-rates = <25000000>;
+	fsl,sai-mclk-direction-output;
+	fsl,sai-asynchronous;
+	status = "okay";
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_main_usb>;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	vbus-supply = <&reg_main_usb>;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vqmmc-supply = <&reg_main_3v3>;
+	vmmc-supply = <&reg_main_3v3>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_pcie1: pcie1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x16
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0		0xd6
+			MX8MQ_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC		0xd6
+			MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK		0xd6
+			MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC		0xd6
+			MX8MQ_IOMUXC_SAI2_RXC_SAI2_RX_BCLK		0xd6
+			MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK		0xd6
+			MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0		0xd6
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x45
+			MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x45
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B		0x0
+			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
+			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
+			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
+			MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3
+			MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3
+			MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3
+		>;
+	};
+};
diff --git a/arch/arm/dts/imx8mq-nitrogen-som.dtsi b/arch/arm/dts/imx8mq-nitrogen-som.dtsi
new file mode 100644
index 0000000000..36fc428ebe
--- /dev/null
+++ b/arch/arm/dts/imx8mq-nitrogen-som.dtsi
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2018 Boundary Devices
+ * Copyright 2021 Lucas Stach <dev@lynxeye.de>
+ */
+
+#include "imx8mq.dtsi"
+
+/ {
+	model = "Boundary Devices i.MX8MQ Nitrogen8M";
+	compatible = "boundary,imx8mq-nitrogen8m-som", "fsl,imx8mq";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_1p8v: regulator-fixed-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_snvs: regulator-fixed-snvs {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_SNVS";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&{/opp-table/opp-800000000} {
+	opp-microvolt = <1000000>;
+};
+
+&{/opp-table/opp-1000000000} {
+	opp-microvolt = <1000000>;
+};
+
+&A53_0 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_arm_dram>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c1_pca9546>;
+		reg = <0x70>;
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c1a: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg_arm_dram: regulator@60 {
+				compatible = "fcs,fan53555";
+				reg = <0x60>;
+				regulator-name = "VDD_ARM_DRAM_1V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+		};
+
+		i2c1b: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg_dram_1p1v: regulator@60 {
+				compatible = "fcs,fan53555";
+				reg = <0x60>;
+				regulator-name = "NVCC_DRAM_1P1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+		};
+
+		i2c1c: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg_soc_gpu_vpu: regulator@60 {
+				compatible = "fcs,fan53555";
+				reg = <0x60>;
+				regulator-name = "VDD_SOC_GPU_VPU";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-always-on;
+			};
+		};
+
+		i2c1d: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&pgc_gpu {
+	power-supply = <&reg_soc_gpu_vpu>;
+};
+
+&pgc_vpu {
+	power-supply = <&reg_soc_gpu_vpu>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vqmmc-supply = <&reg_1p8v>;
+	vmmc-supply = <&reg_snvs>;
+	bus-width = <8>;
+	non-removable;
+	no-mmc-hs400;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO		0x23
+			MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x59
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f
+			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x4000007f
+		>;
+	};
+
+	pinctrl_i2c1_pca9546: i2c1-pca9546grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x49
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x45
+			MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x45
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x83
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xc3
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3
+			MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0xc1
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x8d
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xcd
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xcd
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xcd
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xcd
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xcd
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xcd
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xcd
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xcd
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xcd
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK			0x9f
+			MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD			0xdf
+			MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xdf
+			MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xdf
+			MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xdf
+			MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xdf
+			MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xdf
+			MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xdf
+			MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xdf
+			MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xdf
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
diff --git a/arch/arm/dts/imx8mq-u-boot.dtsi b/arch/arm/dts/imx8mq-u-boot.dtsi
new file mode 100644
index 0000000000..ece14696fb
--- /dev/null
+++ b/arch/arm/dts/imx8mq-u-boot.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ */
+
+/ {
+	binman: binman {
+		multiple-images;
+	};
+
+};
+
+&binman {
+	u-boot-spl-ddr {
+		filename = "u-boot-spl-ddr.bin";
+		pad-byte = <0xff>;
+		align-size = <4>;
+		align = <4>;
+
+		u-boot-spl {
+			align-end = <4>;
+		};
+
+		blob_1: blob-ext@1 {
+			filename = "lpddr4_pmu_train_1d_imem.bin";
+			size = <0x8000>;
+		};
+
+		blob_2: blob-ext@2 {
+			filename = "lpddr4_pmu_train_1d_dmem.bin";
+			size = <0x4000>;
+		};
+
+		blob_3: blob-ext@3 {
+			filename = "lpddr4_pmu_train_2d_imem.bin";
+			size = <0x8000>;
+		};
+
+		blob_4: blob-ext@4 {
+			filename = "lpddr4_pmu_train_2d_dmem.bin";
+			size = <0x4000>;
+		};
+	};
+
+	signed_hdmi {
+		filename = "signed_hdmi.bin";
+
+		blob_5: blob-ext@5 {
+			filename = "signed_hdmi_imx8m.bin";
+		};
+	};
+
+	spl {
+		filename = "spl.bin";
+
+		mkimage {
+			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000";
+
+			blob {
+				filename = "u-boot-spl-ddr.bin";
+			};
+		};
+	};
+
+	itb {
+		filename = "u-boot.itb";
+
+		fit {
+			description = "Configuration to load ATF before U-Boot";
+			#address-cells = <1>;
+			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+
+			images {
+				uboot {
+					description = "U-Boot (64-bit)";
+					type = "standalone";
+					arch = "arm64";
+					compression = "none";
+					load = <CONFIG_SYS_TEXT_BASE>;
+
+					uboot_blob: blob-ext {
+						filename = "u-boot-nodtb.bin";
+					};
+				};
+
+				atf {
+					description = "ARM Trusted Firmware";
+					type = "firmware";
+					arch = "arm64";
+					compression = "none";
+					load = <0x910000>;
+					entry = <0x910000>;
+
+					atf_blob: blob-ext {
+						filename = "bl31.bin";
+					};
+				};
+
+				fdt {
+					description = "NAME";
+					type = "flat_dt";
+					compression = "none";
+
+					uboot_fdt_blob: blob-ext {
+						filename = "u-boot.dtb";
+					};
+				};
+			};
+
+			configurations {
+				default = "conf";
+
+				conf {
+					description = "NAME";
+					firmware = "uboot";
+					loadables = "atf";
+					fdt = "fdt";
+				};
+			};
+		};
+	};
+
+	imx-boot {
+		filename = "flash.bin";
+		pad-byte = <0x00>;
+
+		spl: blob-ext@1 {
+			offset = <0x0>;
+			filename = "spl.bin";
+		};
+
+		uboot: blob-ext@2 {
+			offset = <0x57c00>;
+			filename = "u-boot.itb";
+		};
+	};
+};
diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig
index 276b8bd974..c719da4c8b 100644
--- a/arch/arm/mach-imx/imx8m/Kconfig
+++ b/arch/arm/mach-imx/imx8m/Kconfig
@@ -44,6 +44,12 @@ config TARGET_IMX8MQ_PHANBELL
         select IMX8MQ
         select IMX8M_LPDDR4
 
+config TARGET_IMX8MQ_REFORM2
+	bool "imx8mq_reform2"
+	select BINMAN
+	select IMX8MQ
+	select IMX8M_LPDDR4
+
 config TARGET_IMX8MM_EVK
 	bool "imx8mm LPDDR4 EVK board"
 	select BINMAN
@@ -167,6 +173,7 @@ source "board/freescale/imx8mp_evk/Kconfig"
 source "board/gateworks/venice/Kconfig"
 source "board/google/imx8mq_phanbell/Kconfig"
 source "board/kontron/sl-mx8mm/Kconfig"
+source "board/mntre/imx8mq_reform2/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mp/Kconfig"
 source "board/ronetix/imx8mq-cm/Kconfig"
diff --git a/arch/arm/mach-imx/imx8m/imximage.cfg b/arch/arm/mach-imx/imx8m/imximage.cfg
index 714b24273b..2a3f959183 100644
--- a/arch/arm/mach-imx/imx8m/imximage.cfg
+++ b/arch/arm/mach-imx/imx8m/imximage.cfg
@@ -1,17 +1,11 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
- * Copyright 2018 NXP
+ * Copyright 2018-2021 NXP
  */
 
 #define __ASSEMBLY__
 
 FIT
 BOOT_FROM	sd
-SIGNED_HDMI	signed_hdmi_imx8m.bin
-LOADER		spl/u-boot-spl-ddr.bin	0x7E1000
-SECOND_LOADER	u-boot.itb		0x40200000 0x60000
-
-DDR_FW lpddr4_pmu_train_1d_imem.bin
-DDR_FW lpddr4_pmu_train_1d_dmem.bin
-DDR_FW lpddr4_pmu_train_2d_imem.bin
-DDR_FW lpddr4_pmu_train_2d_dmem.bin
+SIGNED_HDMI	signed_hdmi.bin
+LOADER		u-boot-spl-ddr.bin	0x7e1000
diff --git a/board/mntre/imx8mq_reform2/Kconfig b/board/mntre/imx8mq_reform2/Kconfig
new file mode 100644
index 0000000000..f9260cb7f5
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_IMX8MQ_REFORM2
+
+config SYS_BOARD
+	default "imx8mq_reform2"
+
+config SYS_VENDOR
+	default "mntre"
+
+config SYS_CONFIG_NAME
+	default "imx8mq_reform2"
+
+config IMX_CONFIG
+	default "arch/arm/mach-imx/imx8m/imximage.cfg"
+
+endif
diff --git a/board/mntre/imx8mq_reform2/MAINTAINERS b/board/mntre/imx8mq_reform2/MAINTAINERS
new file mode 100644
index 0000000000..946f287ecf
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/MAINTAINERS
@@ -0,0 +1,7 @@
+REFORM2 IMX8MQ BOARD
+M:	Lukas F. Hartmann <lukas@mntre.com>
+M:	Patrick Wildt <patrick@blueri.se>
+S:	Maintained
+F:	board/mntre/imx8mq_reform2/
+F:	include/configs/imx8mq_reform2.h
+F:	configs/imx8mq_reform2_defconfig
diff --git a/board/mntre/imx8mq_reform2/Makefile b/board/mntre/imx8mq_reform2/Makefile
new file mode 100644
index 0000000000..2efd56bb4a
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/Makefile
@@ -0,0 +1,12 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+obj-y += imx8mq_reform2.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o
+endif
diff --git a/board/mntre/imx8mq_reform2/imx8mq_reform2.c b/board/mntre/imx8mq_reform2/imx8mq_reform2.c
new file mode 100644
index 0000000000..f7cb32dd98
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/imx8mq_reform2.c
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ * Copyright (C) 2018, Boundary Devices <info@boundarydevices.com>
+ */
+
+#include <common.h>
+#include <env.h>
+#include <init.h>
+#include <malloc.h>
+#include <errno.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm-generic/gpio.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <asm/arch/imx8mq_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/arch/clock.h>
+#include <spl.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <power/pmic.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_FSEL1)
+
+#define WDOG_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart_pads[] = {
+	IMX8MQ_PAD_UART1_RXD__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	IMX8MQ_PAD_UART1_TXD__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+int board_early_init_f(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+	set_wdog_reset(wdog);
+
+	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
+
+	return 0;
+}
+
+#ifdef CONFIG_FEC_MXC
+
+#define PHY_RESET	IMX_GPIO_NR(1, 9)
+#define PHY_RX_CTL	IMX_GPIO_NR(1, 24)
+#define PHY_RXC		IMX_GPIO_NR(1, 25)
+#define PHY_RD0		IMX_GPIO_NR(1, 26)
+#define PHY_RD1		IMX_GPIO_NR(1, 27)
+#define PHY_RD2		IMX_GPIO_NR(1, 28)
+#define PHY_RD3		IMX_GPIO_NR(1, 29)
+
+#define STRAP_AR8035	(0x28) // 0010 1000
+
+static const iomux_v3_cfg_t enet_ar8035_gpio_pads[] = {
+	IMX8MQ_PAD_GPIO1_IO09__GPIO1_IO9 | MUX_PAD_CTRL(PAD_CTL_DSE6),
+	IMX8MQ_PAD_ENET_RD0__GPIO1_IO26 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RD1__GPIO1_IO27 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RD2__GPIO1_IO28 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RD3__GPIO1_IO29 | MUX_PAD_CTRL(0xd1),
+	IMX8MQ_PAD_ENET_RX_CTL__GPIO1_IO24 | MUX_PAD_CTRL(0x91),
+	/* 1.8V(1)/1.5V select(0) */
+	IMX8MQ_PAD_ENET_RXC__GPIO1_IO25 | MUX_PAD_CTRL(0xd1),
+};
+
+static const iomux_v3_cfg_t enet_ar8035_pads[] = {
+	IMX8MQ_PAD_ENET_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RX_CTL__ENET_RGMII_RX_CTL | MUX_PAD_CTRL(0x91),
+	IMX8MQ_PAD_ENET_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(0x91),
+};
+
+static void setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *gpr =
+		(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+	/* Pull PHY into reset */
+	gpio_request(PHY_RESET, "fec_rst");
+	gpio_direction_output(PHY_RESET, 0);
+
+	/* Configure ethernet pins value as GPIOs */
+	gpio_request(PHY_RD0, "fec_rd0");
+	gpio_direction_output(PHY_RD0, 0);
+	gpio_request(PHY_RD1, "fec_rd1");
+	gpio_direction_output(PHY_RD1, 0);
+	gpio_request(PHY_RD2, "fec_rd2");
+	gpio_direction_output(PHY_RD2, 0);
+	gpio_request(PHY_RD3, "fec_rd3");
+	gpio_direction_output(PHY_RD3, 1);
+	gpio_request(PHY_RX_CTL, "fec_rx_ctl");
+	gpio_direction_output(PHY_RX_CTL, 0);
+	gpio_request(PHY_RXC, "fec_rxc");
+	gpio_direction_output(PHY_RXC, 1);
+
+	/* Set ethernet pins to GPIO to bootstrap PHY */
+	imx_iomux_v3_setup_multiple_pads(enet_ar8035_gpio_pads,
+	    ARRAY_SIZE(enet_ar8035_gpio_pads));
+
+	/* Use 125M anatop REF_CLK1 for ENET1, not from external */
+	clrsetbits_le32(&gpr->gpr[1], BIT(13) | BIT(17), 0);
+	/* Enable RGMII TX clk output */
+	setbits_le32(&gpr->gpr[1], BIT(22));
+	set_clk_enet(ENET_125MHZ);
+
+	/* 1 ms minimum reset pulse for ar8035 */
+	mdelay(1);
+
+	/* Release PHY from reset */
+	gpio_set_value(PHY_RESET, 1);
+
+	/* strap hold time for AR8035, 5 fails, 6 works, so 12 should be safe */
+	udelay(12);
+
+	/* Change ethernet pins back to normal function */
+	imx_iomux_v3_setup_multiple_pads(enet_ar8035_pads,
+	    ARRAY_SIZE(enet_ar8035_pads));
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	int val;
+
+	/*
+	 * Ar803x phy SmartEEE feature cause link status generates glitch,
+	 * which cause ethernet link down/up issue, so disable SmartEEE
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val & ~(1 << 8));
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x0007);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+	val &= ~0x11c;
+	val |= 0x80; /* 1/2 drive strength */
+	val |= 0x18; /* 125 MHz */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+	/* rgmii tx clock delay enable */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val | 0x0100);
+
+	phydev->supported = phydev->drv->features;
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+	return 0;
+}
+#endif
+
+#define USB1_HUB_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
+#define USB1_HUB_RESET		IMX_GPIO_NR(1, 14)
+
+static void setup_usb(void)
+{
+	imx_iomux_v3_setup_pad(IMX8MQ_PAD_GPIO1_IO14__GPIO1_IO14 |
+	    MUX_PAD_CTRL(USB1_HUB_PAD_CTRL));
+	gpio_request(USB1_HUB_RESET, "usb1_rst");
+	gpio_direction_output(USB1_HUB_RESET, 0);
+	mdelay(10);
+	gpio_set_value(USB1_HUB_RESET, 1);
+}
+
+int board_init(void)
+{
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+	setup_usb();
+
+#if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_DWC3)
+	init_usb_clk();
+#endif
+
+	return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+	return devno;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "Reform2");
+	env_set("board_rev", "iMX8MQ");
+#endif
+
+	return 0;
+}
diff --git a/board/mntre/imx8mq_reform2/imximage.cfg b/board/mntre/imx8mq_reform2/imximage.cfg
new file mode 100644
index 0000000000..74f12b30d2
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/imximage.cfg
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2021 NXP
+ */
+
+#define __ASSEMBLY__
+
+FIT
+BOOT_FROM	sd
+SIGNED_HDMI	signed_hdmi.bin
+LOADER		mkimage.flash.mkimage	0x7e1000
diff --git a/board/mntre/imx8mq_reform2/lpddr4_timing.c b/board/mntre/imx8mq_reform2/lpddr4_timing.c
new file mode 100644
index 0000000000..e5303db0f8
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/lpddr4_timing.c
@@ -0,0 +1,1014 @@
+/*
+ * Copyright 2019 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Generated code from MX8M_DDR_tool
+ * Align with uboot version:
+ * imx_v2018.03_4.14.78_1.0.0_ga ~ imx_v2018.04_4.19.35_1.0.0_ga
+ */
+#include "lpddr4_timing_ch2.h"
+
+static struct dram_cfg_param lpddr4_ddrc_cfg[] = {
+	/** Initialize DDRC registers **/
+	{ DDRC_DBG1(0), 1 },
+	/* selfref_en=1, SDRAM enter self-refresh state */
+	{ DDRC_PWRCTL(0), 1 },
+	{ DDRC_MSTR(0), 0xa0080020 | (CH2_LPDDR4_CS << 24) },
+	{ DDRC_MSTR2(0), 0 },
+	{ DDRC_DERATEEN(0), 0x0203 },
+	{ DDRC_DERATEINT(0), 0x0003e800 },
+	{ DDRC_RFSHTMG(0), 0x006100e0 },
+	{ DDRC_INIT0(0), 0xc003061c },
+	{ DDRC_INIT1(0), 0x009e0000 },
+	{ DDRC_INIT3(0), 0x00d4002d },
+	{ DDRC_INIT4(0), CH2_VAL_INIT4 },
+	{ DDRC_INIT6(0), 0x0066004a },
+	{ DDRC_INIT7(0), 0x0016004a },
+	{ DDRC_DRAMTMG0(0), 0x1a201b22 },
+	{ DDRC_DRAMTMG1(0), 0x00060633 },
+	{ DDRC_DRAMTMG3(0), 0x00c0c000 },
+	{ DDRC_DRAMTMG4(0), 0x0f04080f },
+	{ DDRC_DRAMTMG5(0), 0x02040c0c },
+	{ DDRC_DRAMTMG6(0), 0x01010007 },
+	{ DDRC_DRAMTMG7(0), 0x0401 },
+	{ DDRC_DRAMTMG12(0), 0x00020600 },
+	{ DDRC_DRAMTMG13(0), 0x0c100002 },
+	{ DDRC_DRAMTMG14(0), 0xe6 },
+	{ DDRC_DRAMTMG17(0), 0x00a00050 },
+	{ DDRC_ZQCTL0(0), 0xc3200018 },
+	{ DDRC_ZQCTL1(0), 0x028061a8 },
+	{ DDRC_ZQCTL2(0), 0 },
+	{ DDRC_DFITMG0(0), 0x0497820a },
+	{ DDRC_DFITMG1(0), 0x00080303 },
+	{ DDRC_DFIUPD0(0), 0xe0400018 },
+	{ DDRC_DFIUPD1(0), 0x00df00e4 },
+	{ DDRC_DFIUPD2(0), 0x80000000 },
+	{ DDRC_DFIMISC(0), 0x11 },
+	{ DDRC_DFITMG2(0), 0x170a },
+	{ DDRC_DBICTL(0), 1 },
+	{ DDRC_DFIPHYMSTR(0), 1 },
+	{ DDRC_RANKCTL(0), 0x0639 },
+	{ DDRC_DRAMTMG2(0), 0x070e1617 },
+
+	/* address mapping */
+	{ DDRC_ADDRMAP0(0), CH2_VAL_DDRC_ADDRMAP0 },
+	{ DDRC_ADDRMAP3(0), 0 },
+	/* addrmap_col_b10 and addrmap_col_b11 set to de-activated (5-bit width) */
+	{ DDRC_ADDRMAP4(0), 0x1f1f },
+	/* bank interleave */
+	/* addrmap_bank_b2, addrmap_bank_b1, addrmap_bank_b0 */
+	{ DDRC_ADDRMAP1(0), 0x00080808 },
+	/* addrmap_row_b11, addrmap_row_b10_b2, addrmap_row_b1, addrmap_row_b0 */
+	{ DDRC_ADDRMAP5(0), 0x07070707 },
+	/* addrmap_row_b15, addrmap_row_b14, addrmap_row_b13, addrmap_row_b12 */
+	{ DDRC_ADDRMAP6(0), CH2_VAL_DDRC_ADDRMAP6 },
+	{ DDRC_ADDRMAP7(0), 0x0f0f },
+	{ DDRC_FREQ1_DERATEEN(0), 1 },
+	{ DDRC_FREQ1_DERATEINT(0), 0xd0c0 },
+	{ DDRC_FREQ1_RFSHCTL0(0), 0x0020d040 },
+	{ DDRC_FREQ1_RFSHTMG(0), 0x0014002f },
+	{ DDRC_FREQ1_INIT3(0), 0x00940009 },
+	{ DDRC_FREQ1_INIT4(0), CH2_VAL_INIT4 },
+	{ DDRC_FREQ1_INIT6(0), 0x0066004a },
+	{ DDRC_FREQ1_INIT7(0), 0x0016004a },
+	{ DDRC_FREQ1_DRAMTMG0(0), 0x0b070508 },
+	{ DDRC_FREQ1_DRAMTMG1(0), 0x0003040b },
+	{ DDRC_FREQ1_DRAMTMG2(0), 0x0305090c },
+	{ DDRC_FREQ1_DRAMTMG3(0), 0x00505000 },
+	{ DDRC_FREQ1_DRAMTMG4(0), 0x04040204 },
+	{ DDRC_FREQ1_DRAMTMG5(0), 0x02030303 },
+	{ DDRC_FREQ1_DRAMTMG6(0), 0x01010004 },
+	{ DDRC_FREQ1_DRAMTMG7(0), 0x0301 },
+	{ DDRC_FREQ1_DRAMTMG12(0), 0x00020300 },
+	{ DDRC_FREQ1_DRAMTMG13(0), 0x0a100002 },
+	{ DDRC_FREQ1_DRAMTMG14(0), 0x31 },
+	{ DDRC_FREQ1_DRAMTMG17(0), 0x00220011 },
+	{ DDRC_FREQ1_ZQCTL0(0), 0xc0a70006 },
+	{ DDRC_FREQ1_DFITMG0(0), 0x03858202 },
+	{ DDRC_FREQ1_DFITMG1(0), 0x00080303 },
+	{ DDRC_FREQ1_DFITMG2(0), 0x0502 },
+	{ DDRC_ODTMAP(0), 0 },
+	{ DDRC_SCHED(0), 0x29001505 },
+	{ DDRC_SCHED1(0), 0x2c },
+	{ DDRC_PERFHPR1(0), 0x5900575b },
+	{ DDRC_PERFLPR1(0), 0x90000096 },
+	{ DDRC_PERFWR1(0), 0x1000012c },
+	{ DDRC_DBG0(0), 0x16 },
+	{ DDRC_DBG1(0), 0 },
+	{ DDRC_DBGCMD(0), 0 },
+	{ DDRC_SWCTL(0), 1 },
+	{ DDRC_POISONCFG(0), 0x11 },
+	{ DDRC_PCCFG(0), 0x0111 },
+	{ DDRC_PCFGR_0(0), 0x10f3 },
+	{ DDRC_PCFGW_0(0), 0x72ff },
+	{ DDRC_PCTRL_0(0), 1 },
+	{ DDRC_PCFGQOS0_0(0), 0x0e00 },
+	{ DDRC_PCFGQOS1_0(0), 0x0062ffff },
+	{ DDRC_PCFGWQOS0_0(0), 0x0e00 },
+	{ DDRC_PCFGWQOS1_0(0), 0xffff },
+};
+
+/* PHY Initialize Configuration */
+static struct dram_cfg_param lpddr4_ddrphy_cfg[] = {
+	{ 0x100a0, 0 },
+	{ 0x100a1, 1 },
+	{ 0x100a2, 2 },
+	{ 0x100a3, 3 },
+	{ 0x100a4, 4 },
+	{ 0x100a5, 5 },
+	{ 0x100a6, 6 },
+	{ 0x100a7, 7 },
+	{ 0x110a0, 0 },
+	{ 0x110a1, 1 },
+	{ 0x110a2, 2 },
+	{ 0x110a3, 3 },
+	{ 0x110a4, 4 },
+	{ 0x110a5, 5 },
+	{ 0x110a6, 6 },
+	{ 0x110a7, 7 },
+	{ 0x120a0, 0 },
+	{ 0x120a1, 1 },
+	{ 0x120a2, 2 },
+	{ 0x120a3, 3 },
+	{ 0x120a4, 4 },
+	{ 0x120a5, 5 },
+	{ 0x120a6, 6 },
+	{ 0x120a7, 7 },
+	{ 0x130a0, 0 },
+	{ 0x130a1, 1 },
+	{ 0x130a2, 2 },
+	{ 0x130a3, 3 },
+	{ 0x130a4, 4 },
+	{ 0x130a5, 5 },
+	{ 0x130a6, 6 },
+	{ 0x130a7, 7 },
+	{ 0x1005f, 0x01ff },
+	{ 0x1015f, 0x01ff },
+	{ 0x1105f, 0x01ff },
+	{ 0x1115f, 0x01ff },
+	{ 0x1205f, 0x01ff },
+	{ 0x1215f, 0x01ff },
+	{ 0x1305f, 0x01ff },
+	{ 0x1315f, 0x01ff },
+	{ 0x11005f, 0x01ff },
+	{ 0x11015f, 0x01ff },
+	{ 0x11105f, 0x01ff },
+	{ 0x11115f, 0x01ff },
+	{ 0x11205f, 0x01ff },
+	{ 0x11215f, 0x01ff },
+	{ 0x11305f, 0x01ff },
+	{ 0x11315f, 0x01ff },
+	{ 0x0055, 0x01ff },
+	{ 0x1055, 0x01ff },
+	{ 0x2055, 0x01ff },
+	{ 0x3055, 0x01ff },
+	{ 0x4055, 0x01ff },
+	{ 0x5055, 0x01ff },
+	{ 0x6055, 0x01ff },
+	{ 0x7055, 0x01ff },
+	{ 0x8055, 0x01ff },
+	{ 0x9055, 0x01ff },
+	{ 0x200c5, 0x19 },
+	{ 0x1200c5, 7 },
+	{ 0x2002e, 2 },
+	{ 0x12002e, 1 },
+	{ 0x90204, 0 },
+	{ 0x190204, 0 },
+	{ 0x20024, 0x01ab },
+	{ 0x2003a, 0 },
+	{ 0x120024, 0x01ab },
+	{ 0x2003a, 0 },
+	{ 0x20056, 3 },
+	{ 0x120056, 3 },
+	{ 0x1004d, 0x0e00 },
+	{ 0x1014d, 0x0e00 },
+	{ 0x1104d, 0x0e00 },
+	{ 0x1114d, 0x0e00 },
+	{ 0x1204d, 0x0e00 },
+	{ 0x1214d, 0x0e00 },
+	{ 0x1304d, 0x0e00 },
+	{ 0x1314d, 0x0e00 },
+	{ 0x11004d, 0x0e00 },
+	{ 0x11014d, 0x0e00 },
+	{ 0x11104d, 0x0e00 },
+	{ 0x11114d, 0x0e00 },
+	{ 0x11204d, 0x0e00 },
+	{ 0x11214d, 0x0e00 },
+	{ 0x11304d, 0x0e00 },
+	{ 0x11314d, 0x0e00 },
+	{ 0x10049, 0x0eba },
+	{ 0x10149, 0x0eba },
+	{ 0x11049, 0x0eba },
+	{ 0x11149, 0x0eba },
+	{ 0x12049, 0x0eba },
+	{ 0x12149, 0x0eba },
+	{ 0x13049, 0x0eba },
+	{ 0x13149, 0x0eba },
+	{ 0x110049, 0x0eba },
+	{ 0x110149, 0x0eba },
+	{ 0x111049, 0x0eba },
+	{ 0x111149, 0x0eba },
+	{ 0x112049, 0x0eba },
+	{ 0x112149, 0x0eba },
+	{ 0x113049, 0x0eba },
+	{ 0x113149, 0x0eba },
+	{ 0x0043, 0x63 },
+	{ 0x1043, 0x63 },
+	{ 0x2043, 0x63 },
+	{ 0x3043, 0x63 },
+	{ 0x4043, 0x63 },
+	{ 0x5043, 0x63 },
+	{ 0x6043, 0x63 },
+	{ 0x7043, 0x63 },
+	{ 0x8043, 0x63 },
+	{ 0x9043, 0x63 },
+	{ 0x20018, 3 },
+	{ 0x20075, 4 },
+	{ 0x20050, 0 },
+	{ 0x20008, 0x0320 },
+	{ 0x120008, 0xa7 },
+	{ 0x20088, 9 },
+	{ 0x200b2, 0xdc },
+	{ 0x10043, 0x05a1 },
+	{ 0x10143, 0x05a1 },
+	{ 0x11043, 0x05a1 },
+	{ 0x11143, 0x05a1 },
+	{ 0x12043, 0x05a1 },
+	{ 0x12143, 0x05a1 },
+	{ 0x13043, 0x05a1 },
+	{ 0x13143, 0x05a1 },
+	{ 0x1200b2, 0xdc },
+	{ 0x110043, 0x05a1 },
+	{ 0x110143, 0x05a1 },
+	{ 0x111043, 0x05a1 },
+	{ 0x111143, 0x05a1 },
+	{ 0x112043, 0x05a1 },
+	{ 0x112143, 0x05a1 },
+	{ 0x113043, 0x05a1 },
+	{ 0x113143, 0x05a1 },
+	{ 0x200fa, 1 },
+	{ 0x1200fa, 1 },
+	{ 0x20019, 1 },
+	{ 0x120019, 1 },
+	{ 0x200f0, 0 },
+	{ 0x200f1, 0 },
+	{ 0x200f2, 0x4444 },
+	{ 0x200f3, 0x8888 },
+	{ 0x200f4, 0x5555 },
+	{ 0x200f5, 0 },
+	{ 0x200f6, 0 },
+	{ 0x200f7, 0xf000 },
+	{ 0x20025, 0 },
+	{ 0x2002d, 0 },
+	{ 0x12002d, 0 },
+	{ 0x200c7, 0x80 },
+	{ 0x1200c7, 0x80 },
+	{ 0x200ca, 0x0106 },
+	{ 0x1200ca, 0x0106 },
+	{ 0x20110, 2 },
+	{ 0x20111, 3 },
+	{ 0x20112, 4 },
+	{ 0x20113, 5 },
+	{ 0x20114, 0 },
+	{ 0x20115, 1 },
+};
+
+/* P0 message block parameter for training firmware */
+static struct dram_cfg_param lpddr4_fsp0_cfg[] = {
+	{ 0xd0000, 0 },
+	{ 0x54003, 0x0c80 },
+	{ 0x54004, 2 },
+	{ 0x54005, 0x2228 },
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54008, 0x131f },
+	{ 0x54009, LPDDR4_HDT_CTL_3200_1D },
+	{ 0x5400b, 2 },
+	{ 0x54012, 0x10 | (CH2_LPDDR4_CS << 8) },
+	{ 0x54019, 0x2dd4 },
+	{ 0x5401a, 0x31 },
+	{ 0x5401b, 0x4a66 },
+	{ 0x5401c, 0x4a08 },
+	{ 0x5401e, 0x16 },
+	{ 0x5401f, 0x2dd4 },
+	{ 0x54020, 0x31 },
+	{ 0x54021, 0x4a66 },
+	{ 0x54022, 0x4a08 },
+	{ 0x54024, 0x16 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, CH2_LPDDR4_CS },
+	{ 0x54032, 0xd400 },
+	{ 0x54033, 0x312d },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x084a },
+	{ 0x54036, 0x4a },
+	{ 0x54037, 0x1600 },
+	{ 0x54038, 0xd400 },
+	{ 0x54039, 0x312d },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x084a },
+	{ 0x5403c, 0x4a },
+	{ 0x5403d, 0x1600 },
+	{ 0xd0000, 1 },
+};
+
+
+/* P1 message block parameter for training firmware */
+static struct dram_cfg_param lpddr4_fsp1_cfg[] = {
+	{ 0xd0000, 0 },
+	{ 0x54002, 1 },
+	{ 0x54003, 0x029c },
+	{ 0x54004, 2 },
+	{ 0x54005, 0x2228 },
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54008, 0x121f },
+	{ 0x54009, LPDDR4_HDT_CTL_3200_1D },
+	{ 0x5400b, 2 },
+	{ 0x54012, 0x10 | (CH2_LPDDR4_CS << 8) },
+	{ 0x54019, 0x0994 },
+	{ 0x5401a, 0x31 },
+	{ 0x5401b, 0x4a66 },
+	{ 0x5401c, 0x4a08 },
+	{ 0x5401e, 0x16 },
+	{ 0x5401f, 0x0994 },
+	{ 0x54020, 0x31 },
+	{ 0x54021, 0x4a66 },
+	{ 0x54022, 0x4a08 },
+	{ 0x54024, 0x16 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, CH2_LPDDR4_CS },
+	{ 0x54032, 0x9400 },
+	{ 0x54033, 0x3109 },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x084a },
+	{ 0x54036, 0x4a },
+	{ 0x54037, 0x1600 },
+	{ 0x54038, 0x9400 },
+	{ 0x54039, 0x3109 },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x084a },
+	{ 0x5403c, 0x4a },
+	{ 0x5403d, 0x1600 },
+	{ 0xd0000, 1 },
+};
+
+
+/* P0 2D message block parameter for training firmware */
+static struct dram_cfg_param lpddr4_fsp0_2d_cfg[] = {
+	{ 0xd0000, 0 },
+	{ 0x54003, 0x0c80 },
+	{ 0x54004, 2 },
+	{ 0x54005, 0x2228 },
+	{ 0x54006, LPDDR4_PHY_VREF_VALUE },
+	{ 0x54008, 0x61 },
+	{ 0x54009, LPDDR4_HDT_CTL_3200_1D },
+	{ 0x5400b, 2 },
+	{ 0x5400d, 0x0100 },
+	{ 0x5400f, 0x0100 },
+	{ 0x54010, 0x1f7f },
+	{ 0x54012, 0x10 | (CH2_LPDDR4_CS << 8) },
+	{ 0x54019, 0x2dd4 },
+	{ 0x5401a, 0x31 },
+	{ 0x5401b, 0x4a66 },
+	{ 0x5401c, 0x4a08 },
+	{ 0x5401e, 0x16 },
+	{ 0x5401f, 0x2dd4 },
+	{ 0x54020, 0x31 },
+	{ 0x54021, 0x4a66 },
+	{ 0x54022, 0x4a08 },
+	{ 0x54024, 0x16 },
+	{ 0x5402b, 0x1000 },
+	{ 0x5402c, CH2_LPDDR4_CS },
+	{ 0x54032, 0xd400 },
+	{ 0x54033, 0x312d },
+	{ 0x54034, 0x6600 },
+	{ 0x54035, 0x084a },
+	{ 0x54036, 0x4a },
+	{ 0x54037, 0x1600 },
+	{ 0x54038, 0xd400 },
+	{ 0x54039, 0x312d },
+	{ 0x5403a, 0x6600 },
+	{ 0x5403b, 0x084a },
+	{ 0x5403c, 0x4a },
+	{ 0x5403d, 0x1600 },
+	{ 0xd0000, 1 },
+};
+
+/* DRAM PHY init engine image */
+static struct dram_cfg_param lpddr4_phy_pie[] = {
+	{ 0xd0000, 0 },
+	{ 0x90000, 0x10 },
+	{ 0x90001, 0x0400 },
+	{ 0x90002, 0x010e },
+	{ 0x90003, 0 },
+	{ 0x90004, 0 },
+	{ 0x90005, 8 },
+	{ 0x90029, 0x0b },
+	{ 0x9002a, 0x0480 },
+	{ 0x9002b, 0x0109 },
+	{ 0x9002c, 8 },
+	{ 0x9002d, 0x0448 },
+	{ 0x9002e, 0x0139 },
+	{ 0x9002f, 8 },
+	{ 0x90030, 0x0478 },
+	{ 0x90031, 0x0109 },
+	{ 0x90032, 0 },
+	{ 0x90033, 0xe8 },
+	{ 0x90034, 0x0109 },
+	{ 0x90035, 2 },
+	{ 0x90036, 0x10 },
+	{ 0x90037, 0x0139 },
+	{ 0x90038, 0x0f },
+	{ 0x90039, 0x07c0 },
+	{ 0x9003a, 0x0139 },
+	{ 0x9003b, 0x44 },
+	{ 0x9003c, 0x0630 },
+	{ 0x9003d, 0x0159 },
+	{ 0x9003e, 0x014f },
+	{ 0x9003f, 0x0630 },
+	{ 0x90040, 0x0159 },
+	{ 0x90041, 0x47 },
+	{ 0x90042, 0x0630 },
+	{ 0x90043, 0x0149 },
+	{ 0x90044, 0x4f },
+	{ 0x90045, 0x0630 },
+	{ 0x90046, 0x0179 },
+	{ 0x90047, 8 },
+	{ 0x90048, 0xe0 },
+	{ 0x90049, 0x0109 },
+	{ 0x9004a, 0 },
+	{ 0x9004b, 0x07c8 },
+	{ 0x9004c, 0x0109 },
+	{ 0x9004d, 0 },
+	{ 0x9004e, 1 },
+	{ 0x9004f, 8 },
+	{ 0x90050, 0 },
+	{ 0x90051, 0x045a },
+	{ 0x90052, 9 },
+	{ 0x90053, 0 },
+	{ 0x90054, 0x0448 },
+	{ 0x90055, 0x0109 },
+	{ 0x90056, 0x40 },
+	{ 0x90057, 0x0630 },
+	{ 0x90058, 0x0179 },
+	{ 0x90059, 1 },
+	{ 0x9005a, 0x0618 },
+	{ 0x9005b, 0x0109 },
+	{ 0x9005c, 0x40c0 },
+	{ 0x9005d, 0x0630 },
+	{ 0x9005e, 0x0149 },
+	{ 0x9005f, 8 },
+	{ 0x90060, 4 },
+	{ 0x90061, 0x48 },
+	{ 0x90062, 0x4040 },
+	{ 0x90063, 0x0630 },
+	{ 0x90064, 0x0149 },
+	{ 0x90065, 0 },
+	{ 0x90066, 4 },
+	{ 0x90067, 0x48 },
+	{ 0x90068, 0x40 },
+	{ 0x90069, 0x0630 },
+	{ 0x9006a, 0x0149 },
+	{ 0x9006b, 0x10 },
+	{ 0x9006c, 4 },
+	{ 0x9006d, 0x18 },
+	{ 0x9006e, 0 },
+	{ 0x9006f, 4 },
+	{ 0x90070, 0x78 },
+	{ 0x90071, 0x0549 },
+	{ 0x90072, 0x0630 },
+	{ 0x90073, 0x0159 },
+	{ 0x90074, 0x0d49 },
+	{ 0x90075, 0x0630 },
+	{ 0x90076, 0x0159 },
+	{ 0x90077, 0x094a },
+	{ 0x90078, 0x0630 },
+	{ 0x90079, 0x0159 },
+	{ 0x9007a, 0x0441 },
+	{ 0x9007b, 0x0630 },
+	{ 0x9007c, 0x0149 },
+	{ 0x9007d, 0x42 },
+	{ 0x9007e, 0x0630 },
+	{ 0x9007f, 0x0149 },
+	{ 0x90080, 1 },
+	{ 0x90081, 0x0630 },
+	{ 0x90082, 0x0149 },
+	{ 0x90083, 0 },
+	{ 0x90084, 0xe0 },
+	{ 0x90085, 0x0109 },
+	{ 0x90086, 0x0a },
+	{ 0x90087, 0x10 },
+	{ 0x90088, 0x0109 },
+	{ 0x90089, 9 },
+	{ 0x9008a, 0x03c0 },
+	{ 0x9008b, 0x0149 },
+	{ 0x9008c, 9 },
+	{ 0x9008d, 0x03c0 },
+	{ 0x9008e, 0x0159 },
+	{ 0x9008f, 0x18 },
+	{ 0x90090, 0x10 },
+	{ 0x90091, 0x0109 },
+	{ 0x90092, 0 },
+	{ 0x90093, 0x03c0 },
+	{ 0x90094, 0x0109 },
+	{ 0x90095, 0x18 },
+	{ 0x90096, 4 },
+	{ 0x90097, 0x48 },
+	{ 0x90098, 0x18 },
+	{ 0x90099, 4 },
+	{ 0x9009a, 0x58 },
+	{ 0x9009b, 0x0a },
+	{ 0x9009c, 0x10 },
+	{ 0x9009d, 0x0109 },
+	{ 0x9009e, 2 },
+	{ 0x9009f, 0x10 },
+	{ 0x900a0, 0x0109 },
+	{ 0x900a1, 5 },
+	{ 0x900a2, 0x07c0 },
+	{ 0x900a3, 0x0109 },
+	{ 0x900a4, 0x10 },
+	{ 0x900a5, 0x10 },
+	{ 0x900a6, 0x0109 },
+	{ 0x40000, 0x0811 },
+	{ 0x40020, 0x0880 },
+	{ 0x40040, 0 },
+	{ 0x40060, 0 },
+	{ 0x40001, 0x4008 },
+	{ 0x40021, 0x83 },
+	{ 0x40041, 0x4f },
+	{ 0x40061, 0 },
+	{ 0x40002, 0x4040 },
+	{ 0x40022, 0x83 },
+	{ 0x40042, 0x51 },
+	{ 0x40062, 0 },
+	{ 0x40003, 0x0811 },
+	{ 0x40023, 0x0880 },
+	{ 0x40043, 0 },
+	{ 0x40063, 0 },
+	{ 0x40004, 0x0720 },
+	{ 0x40024, 0x0f },
+	{ 0x40044, 0x1740 },
+	{ 0x40064, 0 },
+	{ 0x40005, 0x16 },
+	{ 0x40025, 0x83 },
+	{ 0x40045, 0x4b },
+	{ 0x40065, 0 },
+	{ 0x40006, 0x0716 },
+	{ 0x40026, 0x0f },
+	{ 0x40046, 0x2001 },
+	{ 0x40066, 0 },
+	{ 0x40007, 0x0716 },
+	{ 0x40027, 0x0f },
+	{ 0x40047, 0x2800 },
+	{ 0x40067, 0 },
+	{ 0x40008, 0x0716 },
+	{ 0x40028, 0x0f },
+	{ 0x40048, 0x0f00 },
+	{ 0x40068, 0 },
+	{ 0x40009, 0x0720 },
+	{ 0x40029, 0x0f },
+	{ 0x40049, 0x1400 },
+	{ 0x40069, 0 },
+	{ 0x4000a, 0x0e08 },
+	{ 0x4002a, 0x0c15 },
+	{ 0x4004a, 0 },
+	{ 0x4006a, 0 },
+	{ 0x4000b, 0x0623 },
+	{ 0x4002b, 0x15 },
+	{ 0x4004b, 0 },
+	{ 0x4006b, 0 },
+	{ 0x4000c, 0x4028 },
+	{ 0x4002c, 0x80 },
+	{ 0x4004c, 0 },
+	{ 0x4006c, 0 },
+	{ 0x4000d, 0x0e08 },
+	{ 0x4002d, 0x0c1a },
+	{ 0x4004d, 0 },
+	{ 0x4006d, 0 },
+	{ 0x4000e, 0x0623 },
+	{ 0x4002e, 0x1a },
+	{ 0x4004e, 0 },
+	{ 0x4006e, 0 },
+	{ 0x4000f, 0x4040 },
+	{ 0x4002f, 0x80 },
+	{ 0x4004f, 0 },
+	{ 0x4006f, 0 },
+	{ 0x40010, 0x2604 },
+	{ 0x40030, 0x15 },
+	{ 0x40050, 0 },
+	{ 0x40070, 0 },
+	{ 0x40011, 0x0708 },
+	{ 0x40031, 5 },
+	{ 0x40051, 0 },
+	{ 0x40071, 0x2002 },
+	{ 0x40012, 8 },
+	{ 0x40032, 0x80 },
+	{ 0x40052, 0 },
+	{ 0x40072, 0 },
+	{ 0x40013, 0x2604 },
+	{ 0x40033, 0x1a },
+	{ 0x40053, 0 },
+	{ 0x40073, 0 },
+	{ 0x40014, 0x0708 },
+	{ 0x40034, 0x0a },
+	{ 0x40054, 0 },
+	{ 0x40074, 0x2002 },
+	{ 0x40015, 0x4040 },
+	{ 0x40035, 0x80 },
+	{ 0x40055, 0 },
+	{ 0x40075, 0 },
+	{ 0x40016, 0x060a },
+	{ 0x40036, 0x15 },
+	{ 0x40056, 0x1200 },
+	{ 0x40076, 0 },
+	{ 0x40017, 0x061a },
+	{ 0x40037, 0x15 },
+	{ 0x40057, 0x1300 },
+	{ 0x40077, 0 },
+	{ 0x40018, 0x060a },
+	{ 0x40038, 0x1a },
+	{ 0x40058, 0x1200 },
+	{ 0x40078, 0 },
+	{ 0x40019, 0x0642 },
+	{ 0x40039, 0x1a },
+	{ 0x40059, 0x1300 },
+	{ 0x40079, 0 },
+	{ 0x4001a, 0x4808 },
+	{ 0x4003a, 0x0880 },
+	{ 0x4005a, 0 },
+	{ 0x4007a, 0 },
+	{ 0x900a7, 0 },
+	{ 0x900a8, 0x0790 },
+	{ 0x900a9, 0x011a },
+	{ 0x900aa, 8 },
+	{ 0x900ab, 0x07aa },
+	{ 0x900ac, 0x2a },
+	{ 0x900ad, 0x10 },
+	{ 0x900ae, 0x07b2 },
+	{ 0x900af, 0x2a },
+	{ 0x900b0, 0 },
+	{ 0x900b1, 0x07c8 },
+	{ 0x900b2, 0x0109 },
+	{ 0x900b3, 0x10 },
+	{ 0x900b4, 0x02a8 },
+	{ 0x900b5, 0x0129 },
+	{ 0x900b6, 8 },
+	{ 0x900b7, 0x0370 },
+	{ 0x900b8, 0x0129 },
+	{ 0x900b9, 0x0a },
+	{ 0x900ba, 0x03c8 },
+	{ 0x900bb, 0x01a9 },
+	{ 0x900bc, 0x0c },
+	{ 0x900bd, 0x0408 },
+	{ 0x900be, 0x0199 },
+	{ 0x900bf, 0x14 },
+	{ 0x900c0, 0x0790 },
+	{ 0x900c1, 0x011a },
+	{ 0x900c2, 8 },
+	{ 0x900c3, 4 },
+	{ 0x900c4, 0x18 },
+	{ 0x900c5, 0x0e },
+	{ 0x900c6, 0x0408 },
+	{ 0x900c7, 0x0199 },
+	{ 0x900c8, 8 },
+	{ 0x900c9, 0x8568 },
+	{ 0x900ca, 0x0108 },
+	{ 0x900cb, 0x18 },
+	{ 0x900cc, 0x0790 },
+	{ 0x900cd, 0x016a },
+	{ 0x900ce, 8 },
+	{ 0x900cf, 0x01d8 },
+	{ 0x900d0, 0x0169 },
+	{ 0x900d1, 0x10 },
+	{ 0x900d2, 0x8558 },
+	{ 0x900d3, 0x0168 },
+	{ 0x900d4, 0x70 },
+	{ 0x900d5, 0x0788 },
+	{ 0x900d6, 0x016a },
+	{ 0x900d7, 0x1ff8 },
+	{ 0x900d8, 0x85a8 },
+	{ 0x900d9, 0x01e8 },
+	{ 0x900da, 0x50 },
+	{ 0x900db, 0x0798 },
+	{ 0x900dc, 0x016a },
+	{ 0x900dd, 0x60 },
+	{ 0x900de, 0x07a0 },
+	{ 0x900df, 0x016a },
+	{ 0x900e0, 8 },
+	{ 0x900e1, 0x8310 },
+	{ 0x900e2, 0x0168 },
+	{ 0x900e3, 8 },
+	{ 0x900e4, 0xa310 },
+	{ 0x900e5, 0x0168 },
+	{ 0x900e6, 0x0a },
+	{ 0x900e7, 0x0408 },
+	{ 0x900e8, 0x0169 },
+	{ 0x900e9, 0x6e },
+	{ 0x900ea, 0 },
+	{ 0x900eb, 0x68 },
+	{ 0x900ec, 0 },
+	{ 0x900ed, 0x0408 },
+	{ 0x900ee, 0x0169 },
+	{ 0x900ef, 0 },
+	{ 0x900f0, 0x8310 },
+	{ 0x900f1, 0x0168 },
+	{ 0x900f2, 0 },
+	{ 0x900f3, 0xa310 },
+	{ 0x900f4, 0x0168 },
+	{ 0x900f5, 0x1ff8 },
+	{ 0x900f6, 0x85a8 },
+	{ 0x900f7, 0x01e8 },
+	{ 0x900f8, 0x68 },
+	{ 0x900f9, 0x0798 },
+	{ 0x900fa, 0x016a },
+	{ 0x900fb, 0x78 },
+	{ 0x900fc, 0x07a0 },
+	{ 0x900fd, 0x016a },
+	{ 0x900fe, 0x68 },
+	{ 0x900ff, 0x0790 },
+	{ 0x90100, 0x016a },
+	{ 0x90101, 8 },
+	{ 0x90102, 0x8b10 },
+	{ 0x90103, 0x0168 },
+	{ 0x90104, 8 },
+	{ 0x90105, 0xab10 },
+	{ 0x90106, 0x0168 },
+	{ 0x90107, 0x0a },
+	{ 0x90108, 0x0408 },
+	{ 0x90109, 0x0169 },
+	{ 0x9010a, 0x58 },
+	{ 0x9010b, 0 },
+	{ 0x9010c, 0x68 },
+	{ 0x9010d, 0 },
+	{ 0x9010e, 0x0408 },
+	{ 0x9010f, 0x0169 },
+	{ 0x90110, 0 },
+	{ 0x90111, 0x8b10 },
+	{ 0x90112, 0x0168 },
+	{ 0x90113, 0 },
+	{ 0x90114, 0xab10 },
+	{ 0x90115, 0x0168 },
+	{ 0x90116, 0 },
+	{ 0x90117, 0x01d8 },
+	{ 0x90118, 0x0169 },
+	{ 0x90119, 0x80 },
+	{ 0x9011a, 0x0790 },
+	{ 0x9011b, 0x016a },
+	{ 0x9011c, 0x18 },
+	{ 0x9011d, 0x07aa },
+	{ 0x9011e, 0x6a },
+	{ 0x9011f, 0x0a },
+	{ 0x90120, 0 },
+	{ 0x90121, 0x01e9 },
+	{ 0x90122, 8 },
+	{ 0x90123, 0x8080 },
+	{ 0x90124, 0x0108 },
+	{ 0x90125, 0x0f },
+	{ 0x90126, 0x0408 },
+	{ 0x90127, 0x0169 },
+	{ 0x90128, 0x0c },
+	{ 0x90129, 0 },
+	{ 0x9012a, 0x68 },
+	{ 0x9012b, 9 },
+	{ 0x9012c, 0 },
+	{ 0x9012d, 0x01a9 },
+	{ 0x9012e, 0 },
+	{ 0x9012f, 0x0408 },
+	{ 0x90130, 0x0169 },
+	{ 0x90131, 0 },
+	{ 0x90132, 0x8080 },
+	{ 0x90133, 0x0108 },
+	{ 0x90134, 8 },
+	{ 0x90135, 0x07aa },
+	{ 0x90136, 0x6a },
+	{ 0x90137, 0 },
+	{ 0x90138, 0x8568 },
+	{ 0x90139, 0x0108 },
+	{ 0x9013a, 0xb7 },
+	{ 0x9013b, 0x0790 },
+	{ 0x9013c, 0x016a },
+	{ 0x9013d, 0x1f },
+	{ 0x9013e, 0 },
+	{ 0x9013f, 0x68 },
+	{ 0x90140, 8 },
+	{ 0x90141, 0x8558 },
+	{ 0x90142, 0x0168 },
+	{ 0x90143, 0x0f },
+	{ 0x90144, 0x0408 },
+	{ 0x90145, 0x0169 },
+	{ 0x90146, 0x0c },
+	{ 0x90147, 0 },
+	{ 0x90148, 0x68 },
+	{ 0x90149, 0 },
+	{ 0x9014a, 0x0408 },
+	{ 0x9014b, 0x0169 },
+	{ 0x9014c, 0 },
+	{ 0x9014d, 0x8558 },
+	{ 0x9014e, 0x0168 },
+	{ 0x9014f, 8 },
+	{ 0x90150, 0x03c8 },
+	{ 0x90151, 0x01a9 },
+	{ 0x90152, 3 },
+	{ 0x90153, 0x0370 },
+	{ 0x90154, 0x0129 },
+	{ 0x90155, 0x20 },
+	{ 0x90156, 0x02aa },
+	{ 0x90157, 9 },
+	{ 0x90158, 0 },
+	{ 0x90159, 0x0400 },
+	{ 0x9015a, 0x010e },
+	{ 0x9015b, 8 },
+	{ 0x9015c, 0xe8 },
+	{ 0x9015d, 0x0109 },
+	{ 0x9015e, 0 },
+	{ 0x9015f, 0x8140 },
+	{ 0x90160, 0x010c },
+	{ 0x90161, 0x10 },
+	{ 0x90162, 0x8138 },
+	{ 0x90163, 0x010c },
+	{ 0x90164, 8 },
+	{ 0x90165, 0x07c8 },
+	{ 0x90166, 0x0101 },
+	{ 0x90167, 8 },
+	{ 0x90168, 0 },
+	{ 0x90169, 8 },
+	{ 0x9016a, 8 },
+	{ 0x9016b, 0x0448 },
+	{ 0x9016c, 0x0109 },
+	{ 0x9016d, 0x0f },
+	{ 0x9016e, 0x07c0 },
+	{ 0x9016f, 0x0109 },
+	{ 0x90170, 0 },
+	{ 0x90171, 0xe8 },
+	{ 0x90172, 0x0109 },
+	{ 0x90173, 0x47 },
+	{ 0x90174, 0x0630 },
+	{ 0x90175, 0x0109 },
+	{ 0x90176, 8 },
+	{ 0x90177, 0x0618 },
+	{ 0x90178, 0x0109 },
+	{ 0x90179, 8 },
+	{ 0x9017a, 0xe0 },
+	{ 0x9017b, 0x0109 },
+	{ 0x9017c, 0 },
+	{ 0x9017d, 0x07c8 },
+	{ 0x9017e, 0x0109 },
+	{ 0x9017f, 8 },
+	{ 0x90180, 0x8140 },
+	{ 0x90181, 0x010c },
+	{ 0x90182, 0 },
+	{ 0x90183, 1 },
+	{ 0x90184, 8 },
+	{ 0x90185, 8 },
+	{ 0x90186, 4 },
+	{ 0x90187, 8 },
+	{ 0x90188, 8 },
+	{ 0x90189, 0x07c8 },
+	{ 0x9018a, 0x0101 },
+	{ 0x90006, 0 },
+	{ 0x90007, 0 },
+	{ 0x90008, 8 },
+	{ 0x90009, 0 },
+	{ 0x9000a, 0 },
+	{ 0x9000b, 0 },
+	{ 0xd00e7, 0x0400 },
+	{ 0x90017, 0 },
+	{ 0x9001f, 0x2a },
+	{ 0x90026, 0x6a },
+	{ 0x400d0, 0 },
+	{ 0x400d1, 0x0101 },
+	{ 0x400d2, 0x0105 },
+	{ 0x400d3, 0x0107 },
+	{ 0x400d4, 0x010f },
+	{ 0x400d5, 0x0202 },
+	{ 0x400d6, 0x020a },
+	{ 0x400d7, 0x020b },
+	{ 0x2003a, 2 },
+	{ 0x2000b, 0x64 },
+	{ 0x2000c, 0xc8 },
+	{ 0x2000d, 0x07d0 },
+	{ 0x2000e, 0x2c },
+	{ 0x12000b, 0x14 },
+	{ 0x12000c, 0x29 },
+	{ 0x12000d, 0x01a1 },
+	{ 0x12000e, 0x10 },
+	{ 0x9000c, 0 },
+	{ 0x9000d, 0x0173 },
+	{ 0x9000e, 0x60 },
+	{ 0x9000f, 0x6110 },
+	{ 0x90010, 0x2152 },
+	{ 0x90011, 0xdfbd },
+	{ 0x90012, 0x60 },
+	{ 0x90013, 0x6152 },
+	{ 0x20010, 0x5a },
+	{ 0x20011, 3 },
+	{ 0x40080, 0xe0 },
+	{ 0x40081, 0x12 },
+	{ 0x40082, 0xe0 },
+	{ 0x40083, 0x12 },
+	{ 0x40084, 0xe0 },
+	{ 0x40085, 0x12 },
+	{ 0x140080, 0xe0 },
+	{ 0x140081, 0x12 },
+	{ 0x140082, 0xe0 },
+	{ 0x140083, 0x12 },
+	{ 0x140084, 0xe0 },
+	{ 0x140085, 0x12 },
+	{ 0x400fd, 0x0f },
+	{ 0x10011, 1 },
+	{ 0x10012, 1 },
+	{ 0x10013, 0x0180 },
+	{ 0x10018, 1 },
+	{ 0x10002, 0x6209 },
+	{ 0x100b2, 1 },
+	{ 0x101b4, 1 },
+	{ 0x102b4, 1 },
+	{ 0x103b4, 1 },
+	{ 0x104b4, 1 },
+	{ 0x105b4, 1 },
+	{ 0x106b4, 1 },
+	{ 0x107b4, 1 },
+	{ 0x108b4, 1 },
+	{ 0x11011, 1 },
+	{ 0x11012, 1 },
+	{ 0x11013, 0x0180 },
+	{ 0x11018, 1 },
+	{ 0x11002, 0x6209 },
+	{ 0x110b2, 1 },
+	{ 0x111b4, 1 },
+	{ 0x112b4, 1 },
+	{ 0x113b4, 1 },
+	{ 0x114b4, 1 },
+	{ 0x115b4, 1 },
+	{ 0x116b4, 1 },
+	{ 0x117b4, 1 },
+	{ 0x118b4, 1 },
+	{ 0x12011, 1 },
+	{ 0x12012, 1 },
+	{ 0x12013, 0x0180 },
+	{ 0x12018, 1 },
+	{ 0x12002, 0x6209 },
+	{ 0x120b2, 1 },
+	{ 0x121b4, 1 },
+	{ 0x122b4, 1 },
+	{ 0x123b4, 1 },
+	{ 0x124b4, 1 },
+	{ 0x125b4, 1 },
+	{ 0x126b4, 1 },
+	{ 0x127b4, 1 },
+	{ 0x128b4, 1 },
+	{ 0x13011, 1 },
+	{ 0x13012, 1 },
+	{ 0x13013, 0x0180 },
+	{ 0x13018, 1 },
+	{ 0x13002, 0x6209 },
+	{ 0x130b2, 1 },
+	{ 0x131b4, 1 },
+	{ 0x132b4, 1 },
+	{ 0x133b4, 1 },
+	{ 0x134b4, 1 },
+	{ 0x135b4, 1 },
+	{ 0x136b4, 1 },
+	{ 0x137b4, 1 },
+	{ 0x138b4, 1 },
+	{ 0x2003a, 2 },
+	{ 0xc0080, 2 },
+	{ 0xd0000, 1 }
+};
+
+static struct dram_fsp_msg lpddr4_dram_fsp_msg[] = {
+	{
+		/* P0 3200mts 1D */
+		.drate = 3200,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp0_cfg,
+		.fsp_cfg_num = ARRAY_SIZE(lpddr4_fsp0_cfg),
+	},
+	{
+		/* P1 667mts 1D */
+		.drate = 667,
+		.fw_type = FW_1D_IMAGE,
+		.fsp_cfg = lpddr4_fsp1_cfg,
+		.fsp_cfg_num = ARRAY_SIZE(lpddr4_fsp1_cfg),
+	},
+	{
+		/* P0 3200mts 2D */
+		.drate = 3200,
+		.fw_type = FW_2D_IMAGE,
+		.fsp_cfg = lpddr4_fsp0_2d_cfg,
+		.fsp_cfg_num = ARRAY_SIZE(lpddr4_fsp0_2d_cfg),
+	},
+};
+
+/* ddr timing config params */
+struct dram_timing_info dram_timing_ch2 = {
+	.ddrc_cfg = lpddr4_ddrc_cfg,
+	.ddrc_cfg_num = ARRAY_SIZE(lpddr4_ddrc_cfg),
+	.ddrphy_cfg = lpddr4_ddrphy_cfg,
+	.ddrphy_cfg_num = ARRAY_SIZE(lpddr4_ddrphy_cfg),
+	.fsp_msg = lpddr4_dram_fsp_msg,
+	.fsp_msg_num = ARRAY_SIZE(lpddr4_dram_fsp_msg),
+	.ddrphy_pie = lpddr4_phy_pie,
+	.ddrphy_pie_num = ARRAY_SIZE(lpddr4_phy_pie),
+	.fsp_table = { 3200, 667, },
+};
diff --git a/board/mntre/imx8mq_reform2/lpddr4_timing_ch2.h b/board/mntre/imx8mq_reform2/lpddr4_timing_ch2.h
new file mode 100644
index 0000000000..7dcc9a7db7
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/lpddr4_timing_ch2.h
@@ -0,0 +1,95 @@
+/*
+ * Copyright Boundary Devices
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <config.h>
+#include <linux/kernel.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/lpddr4_define.h>
+
+/* MNT Reform2 */
+#define CONFIG_DDR_MB 4096
+#define CONFIG_DDR_RANK_BITS 1
+#define CONFIG_DDR_CHANNEL_CNT 2
+
+#ifdef WR_POST_EXT_3200
+#define CH2_VAL_INIT4	((LPDDR4_MR3 << 16) | 0x00020008)
+#else
+#define CH2_VAL_INIT4	((LPDDR4_MR3 << 16) | 8)
+#endif
+
+#if CONFIG_DDR_MB == 1024
+	/* Address map is from MSB 28: r14, r13-r0, b2-b0, c9-c0 */
+#define CH2_VAL_DDRC_ADDRMAP0_R0	0x0000001F
+#define CH2_VAL_DDRC_ADDRMAP6_R0	0x0F070707
+
+#elif CONFIG_DDR_MB == 2048
+	/* Address map is from MSB 28: r15, r14, r13-r0, b2-b0, c9-c0 */
+#define CH2_VAL_DDRC_ADDRMAP0_R0	0x0000001F
+#define CH2_VAL_DDRC_ADDRMAP6_R0	0x07070707
+	/* Address map is from MSB 28: cs, r14, r13-r0, b2-b0, c9-c0 */
+#define CH2_VAL_DDRC_ADDRMAP0_R1	0x00000016
+#define CH2_VAL_DDRC_ADDRMAP6_R1	0x0F070707
+
+#elif CONFIG_DDR_MB == 3072
+	/* Address map is from MSB 29: r15, r14, cs, r13-r0, b2-b0, c9-c0 */
+#define CH2_VAL_DDRC_ADDRMAP0_R1	0x00000015
+#define CH2_VAL_DDRC_ADDRMAP6_R1	0x48080707
+
+#elif CONFIG_DDR_MB == 4096
+	/* Address map is from MSB 29: cs, r15, r14, r13-r0, b2-b0, c9-c0 */
+#define CH2_VAL_DDRC_ADDRMAP0_R1	0x00000017
+#define CH2_VAL_DDRC_ADDRMAP6_R1	0x07070707
+#else
+#error unsupported memory size
+#endif
+
+#define LPDDR4_CS_R0	0x1	/* 0 rank bits, 1 chip select */
+#define LPDDR4_CS_R1	0x3	/* 1 rank bit, 2 chip selects */
+
+#if (CONFIG_DDR_RANK_BITS == 0) || !defined(CH2_VAL_DDRC_ADDRMAP0_R1)
+#ifdef CH2_VAL_DDRC_ADDRMAP0_R0
+#define CH2_LPDDR4_CS			LPDDR4_CS_R0
+#define CH2_VAL_DDRC_ADDRMAP0		CH2_VAL_DDRC_ADDRMAP0_R0
+#define CH2_VAL_DDRC_ADDRMAP6		CH2_VAL_DDRC_ADDRMAP6_R0
+#else
+#error unsupported memory rank/size
+#endif
+/*
+ * rank0 will succeed, even if really rank 1, so we need
+ * to probe memory if rank0 succeeds
+ */
+#if defined(CH2_VAL_DDRC_ADDRMAP0_R0) && defined(CH2_VAL_DDRC_ADDRMAP0_R1)
+#define CH2_LPDDR4_CS_NEW		LPDDR4_CS_R1
+#define CH2_VAL_DDRC_ADDRMAP0_NEW	CH2_VAL_DDRC_ADDRMAP0_R1
+#define CH2_VAL_DDRC_ADDRMAP6_NEW	CH2_VAL_DDRC_ADDRMAP6_R1
+#endif
+
+#elif (CONFIG_DDR_RANK_BITS == 1) || !defined(CH2_VAL_DDRC_ADDRMAP0_R0)
+#ifdef CH2_VAL_DDRC_ADDRMAP0_R1
+#define CH2_LPDDR4_CS			LPDDR4_CS_R1
+#define CH2_VAL_DDRC_ADDRMAP0		CH2_VAL_DDRC_ADDRMAP0_R1
+#define CH2_VAL_DDRC_ADDRMAP6		CH2_VAL_DDRC_ADDRMAP6_R1
+#else
+#error unsupported memory rank/size
+#endif
+
+#if defined(CH2_VAL_DDRC_ADDRMAP0_R0) && defined(CH2_VAL_DDRC_ADDRMAP0_R1)
+#define CH2_LPDDR4_CS_NEW		LPDDR4_CS_R0
+#define CH2_VAL_DDRC_ADDRMAP0_NEW	CH2_VAL_DDRC_ADDRMAP0_R0
+#define CH2_VAL_DDRC_ADDRMAP6_NEW	CH2_VAL_DDRC_ADDRMAP6_R0
+#endif
+
+#else
+#error unsupported rank bits
+#endif
+
+#if (CONFIG_DDR_CHANNEL_CNT == 2)
+#if (CONFIG_DDR_RANK_BITS == 0) && !defined(CH2_VAL_DDRC_ADDRMAP0_R0)
+#error unsupported options
+#endif
+#if (CONFIG_DDR_RANK_BITS == 1) && !defined(CH2_VAL_DDRC_ADDRMAP0_R1)
+#error unsupported options
+#endif
+#endif
diff --git a/board/mntre/imx8mq_reform2/spl.c b/board/mntre/imx8mq_reform2/spl.c
new file mode 100644
index 0000000000..c0885e422c
--- /dev/null
+++ b/board/mntre/imx8mq_reform2/spl.c
@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <hang.h>
+#include <image.h>
+#include <init.h>
+#include <log.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/imx8mq_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/clock.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc_imx.h>
+#include <mmc.h>
+#include <linux/delay.h>
+#include <power/pmic.h>
+#include <spl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern struct dram_timing_info dram_timing_ch2;
+
+static void spl_dram_init(void)
+{
+	ddr_init(&dram_timing_ch2);
+}
+
+#define I2C_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = IMX8MQ_PAD_I2C1_SCL__I2C1_SCL | PC,
+		.gpio_mode = IMX8MQ_PAD_I2C1_SCL__GPIO5_IO14 | PC,
+		.gp = IMX_GPIO_NR(5, 14),
+	},
+	.sda = {
+		.i2c_mode = IMX8MQ_PAD_I2C1_SDA__I2C1_SDA | PC,
+		.gpio_mode = IMX8MQ_PAD_I2C1_SDA__GPIO5_IO15 | PC,
+		.gp = IMX_GPIO_NR(5, 15),
+	},
+};
+
+#define USDHC2_VSEL	IMX_GPIO_NR(1, 8)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 12)
+#define USDHC1_PWR_GPIO IMX_GPIO_NR(2, 10)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		return ret;
+	}
+
+	return 1;
+}
+
+#define USDHC_PAD_CTRL	(PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | \
+			 PAD_CTL_FSEL2)
+#define USDHC_GPIO_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_DSE1)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	IMX8MQ_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA4__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA5__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA6__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_DATA7__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	IMX8MQ_PAD_SD1_RESET_B__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	IMX8MQ_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+	IMX8MQ_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+	IMX8MQ_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+	IMX8MQ_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+	IMX8MQ_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0x16 */
+	IMX8MQ_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
+	IMX8MQ_PAD_SD2_CD_B__GPIO2_IO12 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
+	IMX8MQ_PAD_GPIO1_IO08__GPIO1_IO8 | MUX_PAD_CTRL(0x91),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC1_BASE_ADDR, 0, 8},
+	{USDHC2_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_init(struct bd_info *bis)
+{
+	int i, ret;
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			init_clk_usdhc(0);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(USDHC1_CLK_ROOT);
+			imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
+							 ARRAY_SIZE(usdhc1_pads));
+			gpio_request(USDHC1_PWR_GPIO, "usdhc1_reset");
+			gpio_direction_output(USDHC1_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC1_PWR_GPIO, 1);
+			break;
+		case 1:
+			init_clk_usdhc(1);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(USDHC2_CLK_ROOT);
+			imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
+							 ARRAY_SIZE(usdhc2_pads));
+			gpio_request(USDHC2_VSEL, "usdhc2_vsel");
+			gpio_direction_output(USDHC2_VSEL, 0);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers(%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+#define I2C1_PCA9546_RESET	IMX_GPIO_NR(1, 4)
+#define ARM_DRAM_VSEL		IMX_GPIO_NR(3, 24)
+#define DRAM_1P1_VSEL		IMX_GPIO_NR(2, 11)
+#define SOC_GPU_VPU_VSEL	IMX_GPIO_NR(2, 20)
+
+#define I2C_MUX_ADDR		0x70
+#define I2C_FAN53555_ADDR	0x60
+
+static iomux_v3_cfg_t const power_pads[] = {
+	IMX8MQ_PAD_GPIO1_IO04__GPIO1_IO4 | MUX_PAD_CTRL(0x46),
+};
+
+int power_init_board(void)
+{
+	uint8_t val;
+
+	imx_iomux_v3_setup_multiple_pads(power_pads,
+					 ARRAY_SIZE(usdhc2_pads));
+
+	/* Release I2C multiplexer reset */
+	gpio_request(I2C1_PCA9546_RESET, "pca9546_reset");
+	gpio_direction_output(I2C1_PCA9546_RESET, 1);
+
+	/* Select VSEL0 on voltage regulators */
+	gpio_request(ARM_DRAM_VSEL, "arm_dram_vsel");
+	gpio_direction_output(ARM_DRAM_VSEL, 0);
+	gpio_request(DRAM_1P1_VSEL, "dram_1p1_vsel");
+	gpio_direction_output(DRAM_1P1_VSEL, 0);
+	gpio_request(SOC_GPU_VPU_VSEL, "soc_gpu_vpu_vsel");
+	gpio_direction_output(SOC_GPU_VPU_VSEL, 0);
+
+	/* Set mux to target ARM/DRAM regulator */
+	i2c_write(I2C_MUX_ADDR, 1, 1, NULL, 0);
+	/* .6 + .40 = 1.00 */
+	val = 0x80 + 40;
+	i2c_write(I2C_FAN53555_ADDR, 0, 1, &val, 1);
+	i2c_write(I2C_FAN53555_ADDR, 1, 1, &val, 1);
+
+	/* Set mux to target DRAM regulator */
+	i2c_write(I2C_MUX_ADDR, 2, 1, NULL, 0);
+	/* .6 + .50 = 1.10 */
+	val = 0x80 + 50;
+	i2c_write(I2C_FAN53555_ADDR, 0, 1, &val, 1);
+	i2c_write(I2C_FAN53555_ADDR, 1, 1, &val, 1);
+
+	/* Set mux to target SoC/GPU/VPU regulator */
+	i2c_write(I2C_MUX_ADDR, 4, 1, NULL, 0);
+	/*  .6 + .30 = .90 */
+	val = 0x80 + 30;
+	i2c_write(I2C_FAN53555_ADDR, 0, 1, &val, 1);
+	i2c_write(I2C_FAN53555_ADDR, 1, 1, &val, 1);
+
+	/* Set mux to target peripherals */
+	i2c_write(I2C_MUX_ADDR, 8, 1, NULL, 0);
+
+	return 0;
+}
+
+void spl_board_init(void)
+{
+	puts("Normal Boot\n");
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+	/* Just empty function now - can't decide what to choose */
+	debug("%s: %s\n", __func__, name);
+
+	return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+	int ret;
+
+	/* Clear global data */
+	memset((void *)gd, 0, sizeof(gd_t));
+
+	arch_cpu_init();
+
+	init_uart_clk(0);
+
+	board_early_init_f();
+
+	timer_init();
+
+	preloader_console_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	ret = spl_init();
+	if (ret) {
+		debug("spl_init() failed: %d\n", ret);
+		hang();
+	}
+
+	enable_tzc380();
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+	power_init_board();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	board_init_r(NULL, 0);
+}
diff --git a/configs/imx8mq_reform2_defconfig b/configs/imx8mq_reform2_defconfig
new file mode 100644
index 0000000000..ec6b52117d
--- /dev/null
+++ b/configs/imx8mq_reform2_defconfig
@@ -0,0 +1,82 @@
+CONFIG_ARM=y
+CONFIG_ARCH_IMX8M=y
+CONFIG_SYS_TEXT_BASE=0x40200000
+CONFIG_SYS_MALLOC_LEN=0x600000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_ENV_SIZE=0x1000
+CONFIG_ENV_OFFSET=0x400000
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx8mq-mnt-reform2"
+CONFIG_SPL_TEXT_BASE=0x7E1000
+CONFIG_TARGET_IMX8MQ_REFORM2=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_DRIVERS_MISC=y
+CONFIG_SPL=y
+CONFIG_IMX_HAB=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_SYS_LOAD_ADDR=0x40480000
+CONFIG_FIT=y
+CONFIG_FIT_EXTERNAL_OFFSET=0x3000
+CONFIG_SPL_LOAD_FIT=y
+# CONFIG_USE_SPL_FIT_GENERATOR is not set
+CONFIG_USE_PREBOOT=y
+CONFIG_DEFAULT_FDT_FILE="imx8mq-mnt-reform2.dtb"
+CONFIG_CONSOLE_MUX=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_I2C=y
+CONFIG_SPL_POWER=y
+CONFIG_SPL_WATCHDOG=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
+# CONFIG_CMD_CRC32 is not set
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_MDIO is not set
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
+CONFIG_DM_I2C=y
+CONFIG_SPL_SYS_I2C_LEGACY=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
+CONFIG_PHY=y
+CONFIG_PHY_IMX8MQ_USB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX8M=y
+CONFIG_SPL_POWER_LEGACY=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8M_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_POWER_I2C=y
+CONFIG_DM_RESET=y
+CONFIG_MXC_UART=y
+CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_KEYBOARD=y
diff --git a/include/configs/imx8mq_reform2.h b/include/configs/imx8mq_reform2.h
new file mode 100644
index 0000000000..8aed1acfcf
--- /dev/null
+++ b/include/configs/imx8mq_reform2.h
@@ -0,0 +1,114 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#ifndef __IMX8M_REFORM2_H
+#define __IMX8M_REFORM2_H
+
+#include <linux/sizes.h>
+#include <linux/stringify.h>
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_SPL_MAX_SIZE		(124 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
+
+#ifdef CONFIG_SPL_BUILD
+/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
+#define CONFIG_SPL_STACK		0x187FF0
+#define CONFIG_SPL_BSS_START_ADDR	0x00180000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x2000	/* 8 KB */
+#define CONFIG_SYS_SPL_MALLOC_START	0x42200000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000	/* 512 KB */
+#define CONFIG_SYS_SPL_PTE_RAM_BASE	0x41580000
+
+/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
+#define CONFIG_MALLOC_F_ADDR		0x182000
+/* For RAW image gives a error info not panic */
+#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
+
+#undef CONFIG_DM_MMC
+#endif
+
+#define CONFIG_REMAKE_ELF
+
+/* ENET Config */
+/* ENET1 */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_MII
+#define CONFIG_ETHPRIME			"FEC"
+
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_FEC_MXC_PHYADDR		4
+#define FEC_QUIRK_ENET_MAC
+
+#define CONFIG_PHY_GIGE
+#define IMX_FEC_BASE			0x30BE0000
+#endif
+
+#ifndef CONFIG_SPL_BUILD
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 1) \
+	func(MMC, mmc, 0) \
+	func(USB, usb, 0) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+#endif
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	BOOTENV \
+	"scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+	"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+	"image=Image\0" \
+	"console=ttymxc0,115200\0" \
+	"fdt_addr_r=0x43000000\0"			\
+	"boot_fdt=try\0" \
+	"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
+	"initrd_addr=0x43800000\0"		\
+	"bootm_size=0x10000000\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"stdin=serial,usbkbd\0" \
+
+/* Link Definitions */
+
+#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
+#define CONFIG_SYS_INIT_RAM_SIZE	0x80000
+#define CONFIG_SYS_INIT_SP_OFFSET	\
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR		\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"	/* USDHC2 */
+
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+#define PHYS_SDRAM			0x40000000
+#define PHYS_SDRAM_SIZE			0x100000000	/* 4 GiB DDR */
+
+#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_MAXARGS		64
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+
+#define CONFIG_IMX_BOOTAUX
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_OF_SYSTEM_SETUP
+
+#define CONFIG_SYS_BOOTM_LEN		SZ_128M
+
+#endif