[PATCH v3 0/6] Add LCLK control into Aspeed LPC sub drivers

[PATCH v3 0/6] Add LCLK control into Aspeed LPC sub drivers

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

Hello all,

This series is for appliying below fix to all Aspped LPC sub drivers.
https://lore.kernel.org/all/20201208091748.1920-1-wangzhiqiang.bj@bytedance.com/

An LPC sub driver can be enabled without using the lpc-ctrl driver or it
can be registered ahead of lpc-ctrl depends on each system configuration and
this difference introduces that LPC can be enabled without heart beating of
LCLK so it causes improper handling on host interrupts when the host sends
interrupts in that time frame. Then kernel eventually forcibly disables the
interrupt with dumping stack and printing a 'nobody cared this irq' message
out.

To prevent this issue, all LPC sub drivers should enable LCLK individually
so this patch adds clock control logic into the remaining Aspeed LPC sub
drivers.

Please review this series.

Thanks,
Jae

Changes sinve v2:
 * Rebased it on the latest master.
 * Made dts and bindigs changes' commit message more descriptive.
 * Simplified the -EPROBE_DEFER handling using dev_err_probe().

Changes sinve v1:
 * Added 'clocks' property into ibt and kcs-bmc bindings using
   'aspeed,ast2400-ibt-bmc.txt' and 'aspeed,ast2400-kcs-bmc.yaml'
   respectively because these are not merged into 'aspeed-lpc.yaml' yet.
   The bindings merging could be done using a separate patch later.

Jae Hyun Yoo (6):
  ARM: dts: aspeed: add LCLK setting into LPC IBT node
  dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
  ipmi: bt: add clock control logic
  ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
  dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property
  ipmi: kcs_bmc_aspeed: add clock control logic

 .../bindings/ipmi/aspeed,ast2400-ibt-bmc.txt  |  2 ++
 .../bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml |  7 +++++
 arch/arm/boot/dts/aspeed-g4.dtsi              |  1 +
 arch/arm/boot/dts/aspeed-g5.dtsi              |  5 ++++
 arch/arm/boot/dts/aspeed-g6.dtsi              |  5 ++++
 drivers/char/ipmi/bt-bmc.c                    | 21 +++++++++++++-
 drivers/char/ipmi/kcs_bmc_aspeed.c            | 28 ++++++++++++++++---
 7 files changed, 64 insertions(+), 5 deletions(-)

-- 
2.25.1

[PATCH v3 0/6] Add LCLK control into Aspeed LPC sub drivers

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

Hello all,

This series is for appliying below fix to all Aspped LPC sub drivers.
https://lore.kernel.org/all/20201208091748.1920-1-wangzhiqiang.bj@bytedance.com/

An LPC sub driver can be enabled without using the lpc-ctrl driver or it
can be registered ahead of lpc-ctrl depends on each system configuration and
this difference introduces that LPC can be enabled without heart beating of
LCLK so it causes improper handling on host interrupts when the host sends
interrupts in that time frame. Then kernel eventually forcibly disables the
interrupt with dumping stack and printing a 'nobody cared this irq' message
out.

To prevent this issue, all LPC sub drivers should enable LCLK individually
so this patch adds clock control logic into the remaining Aspeed LPC sub
drivers.

Please review this series.

Thanks,
Jae

Changes sinve v2:
 * Rebased it on the latest master.
 * Made dts and bindigs changes' commit message more descriptive.
 * Simplified the -EPROBE_DEFER handling using dev_err_probe().

Changes sinve v1:
 * Added 'clocks' property into ibt and kcs-bmc bindings using
   'aspeed,ast2400-ibt-bmc.txt' and 'aspeed,ast2400-kcs-bmc.yaml'
   respectively because these are not merged into 'aspeed-lpc.yaml' yet.
   The bindings merging could be done using a separate patch later.

Jae Hyun Yoo (6):
  ARM: dts: aspeed: add LCLK setting into LPC IBT node
  dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
  ipmi: bt: add clock control logic
  ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
  dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property
  ipmi: kcs_bmc_aspeed: add clock control logic

 .../bindings/ipmi/aspeed,ast2400-ibt-bmc.txt  |  2 ++
 .../bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml |  7 +++++
 arch/arm/boot/dts/aspeed-g4.dtsi              |  1 +
 arch/arm/boot/dts/aspeed-g5.dtsi              |  5 ++++
 arch/arm/boot/dts/aspeed-g6.dtsi              |  5 ++++
 drivers/char/ipmi/bt-bmc.c                    | 21 +++++++++++++-
 drivers/char/ipmi/kcs_bmc_aspeed.c            | 28 ++++++++++++++++---
 7 files changed, 64 insertions(+), 5 deletions(-)

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/6] ARM: dts: aspeed: add LCLK setting into LPC IBT node

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property setting into LPC
IBT node as one of required properties to enable the LCLK by the
LPC IBT driver.

Note: dtbs should be re-compiled after applying this change since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
 * No change.

 arch/arm/boot/dts/aspeed-g4.dtsi | 1 +
 arch/arm/boot/dts/aspeed-g5.dtsi | 1 +
 arch/arm/boot/dts/aspeed-g6.dtsi | 1 +
 3 files changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed-g4.dtsi
index b313a1cf5f73..f14dace34c5a 100644
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed-g4.dtsi
@@ -381,6 +381,7 @@ ibt: ibt@140 {
 					compatible = "aspeed,ast2400-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index c7049454c7cb..d0cc4be2de59 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -507,6 +507,7 @@ ibt: ibt@140 {
 					compatible = "aspeed,ast2500-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 			};
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index 5106a424f1ce..465c3549fdc3 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -581,6 +581,7 @@ ibt: ibt@140 {
 					compatible = "aspeed,ast2600-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 			};
-- 
2.25.1

[PATCH v3 1/6] ARM: dts: aspeed: add LCLK setting into LPC IBT node

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property setting into LPC
IBT node as one of required properties to enable the LCLK by the
LPC IBT driver.

Note: dtbs should be re-compiled after applying this change since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
 * No change.

 arch/arm/boot/dts/aspeed-g4.dtsi | 1 +
 arch/arm/boot/dts/aspeed-g5.dtsi | 1 +
 arch/arm/boot/dts/aspeed-g6.dtsi | 1 +
 3 files changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed-g4.dtsi
index b313a1cf5f73..f14dace34c5a 100644
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed-g4.dtsi
@@ -381,6 +381,7 @@ ibt: ibt@140 {
 					compatible = "aspeed,ast2400-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index c7049454c7cb..d0cc4be2de59 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -507,6 +507,7 @@ ibt: ibt@140 {
 					compatible = "aspeed,ast2500-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 			};
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index 5106a424f1ce..465c3549fdc3 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -581,6 +581,7 @@ ibt: ibt@140 {
 					compatible = "aspeed,ast2600-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 			};
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/6] dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property as one of
required properties to enable the LCLK by the LPC IBT driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
 * Added 'clocks' property into ibt bindings using
   'aspeed,ast2400-ibt-bmc.txt' because it's not merged into
   'aspeed-lpc.yaml' yet. The bindings merging could be done using a
   separate patch later.

 .../devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt
index c9902fd4b38b..25f86da804b7 100644
--- a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt
+++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt
@@ -11,6 +11,7 @@ Required properties:
 	"aspeed,ast2500-ibt-bmc"
 	"aspeed,ast2600-ibt-bmc"
 - reg: physical address and size of the registers
+- clocks: clock for the device
 
 Optional properties:
 
@@ -23,4 +24,5 @@ Example:
 		compatible = "aspeed,ast2400-ibt-bmc";
 		reg = <0x1e789140 0x18>;
 		interrupts = <8>;
+		clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 	};
-- 
2.25.1

[PATCH v3 2/6] dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property as one of
required properties to enable the LCLK by the LPC IBT driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
 * Added 'clocks' property into ibt bindings using
   'aspeed,ast2400-ibt-bmc.txt' because it's not merged into
   'aspeed-lpc.yaml' yet. The bindings merging could be done using a
   separate patch later.

 .../devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt
index c9902fd4b38b..25f86da804b7 100644
--- a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt
+++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt
@@ -11,6 +11,7 @@ Required properties:
 	"aspeed,ast2500-ibt-bmc"
 	"aspeed,ast2600-ibt-bmc"
 - reg: physical address and size of the registers
+- clocks: clock for the device
 
 Optional properties:
 
@@ -23,4 +24,5 @@ Example:
 		compatible = "aspeed,ast2400-ibt-bmc";
 		reg = <0x1e789140 0x18>;
 		interrupts = <8>;
+		clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 	};
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/6] ipmi: bt: add clock control logic

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds clock control logic into the LPC
BT driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise this driver will not
be probed correctly.

Fixes: 54f9c4d0778b ("ipmi: add an Aspeed BT IPMI BMC driver")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
---
v2 -> v3:
 * Simplified the -EPROBE_DEFER handling using dev_err_probe().

v1 -> v2:
 * No change.

 drivers/char/ipmi/bt-bmc.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/char/ipmi/bt-bmc.c b/drivers/char/ipmi/bt-bmc.c
index 7450904e330a..f6547ddd7284 100644
--- a/drivers/char/ipmi/bt-bmc.c
+++ b/drivers/char/ipmi/bt-bmc.c
@@ -5,6 +5,7 @@
 
 #include <linux/atomic.h>
 #include <linux/bt-bmc.h>
+#include <linux/clk.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
@@ -62,6 +63,7 @@ struct bt_bmc {
 	wait_queue_head_t	queue;
 	struct timer_list	poll_timer;
 	struct mutex		mutex;
+	struct clk		*clk;
 };
 
 static atomic_t open_count = ATOMIC_INIT(0);
@@ -423,6 +425,16 @@ static int bt_bmc_probe(struct platform_device *pdev)
 	if (IS_ERR(bt_bmc->base))
 		return PTR_ERR(bt_bmc->base);
 
+	bt_bmc->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(bt_bmc->clk))
+		return dev_err_probe(dev, PTR_ERR(bt_bmc->clk),
+				     "Unable to get clock\n");
+	rc = clk_prepare_enable(bt_bmc->clk);
+	if (rc) {
+		dev_err(dev, "Unable to enable clock\n");
+		return rc;
+	}
+
 	mutex_init(&bt_bmc->mutex);
 	init_waitqueue_head(&bt_bmc->queue);
 
@@ -433,7 +445,7 @@ static int bt_bmc_probe(struct platform_device *pdev)
 	rc = misc_register(&bt_bmc->miscdev);
 	if (rc) {
 		dev_err(dev, "Unable to register misc device\n");
-		return rc;
+		goto err;
 	}
 
 	bt_bmc_config_irq(bt_bmc, pdev);
@@ -457,6 +469,11 @@ static int bt_bmc_probe(struct platform_device *pdev)
 	clr_b_busy(bt_bmc);
 
 	return 0;
+
+err:
+	clk_disable_unprepare(bt_bmc->clk);
+
+	return rc;
 }
 
 static int bt_bmc_remove(struct platform_device *pdev)
@@ -466,6 +483,8 @@ static int bt_bmc_remove(struct platform_device *pdev)
 	misc_deregister(&bt_bmc->miscdev);
 	if (bt_bmc->irq < 0)
 		del_timer_sync(&bt_bmc->poll_timer);
+	clk_disable_unprepare(bt_bmc->clk);
+
 	return 0;
 }
 
-- 
2.25.1

[PATCH v3 3/6] ipmi: bt: add clock control logic

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds clock control logic into the LPC
BT driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise this driver will not
be probed correctly.

Fixes: 54f9c4d0778b ("ipmi: add an Aspeed BT IPMI BMC driver")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
---
v2 -> v3:
 * Simplified the -EPROBE_DEFER handling using dev_err_probe().

v1 -> v2:
 * No change.

 drivers/char/ipmi/bt-bmc.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/char/ipmi/bt-bmc.c b/drivers/char/ipmi/bt-bmc.c
index 7450904e330a..f6547ddd7284 100644
--- a/drivers/char/ipmi/bt-bmc.c
+++ b/drivers/char/ipmi/bt-bmc.c
@@ -5,6 +5,7 @@
 
 #include <linux/atomic.h>
 #include <linux/bt-bmc.h>
+#include <linux/clk.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
@@ -62,6 +63,7 @@ struct bt_bmc {
 	wait_queue_head_t	queue;
 	struct timer_list	poll_timer;
 	struct mutex		mutex;
+	struct clk		*clk;
 };
 
 static atomic_t open_count = ATOMIC_INIT(0);
@@ -423,6 +425,16 @@ static int bt_bmc_probe(struct platform_device *pdev)
 	if (IS_ERR(bt_bmc->base))
 		return PTR_ERR(bt_bmc->base);
 
+	bt_bmc->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(bt_bmc->clk))
+		return dev_err_probe(dev, PTR_ERR(bt_bmc->clk),
+				     "Unable to get clock\n");
+	rc = clk_prepare_enable(bt_bmc->clk);
+	if (rc) {
+		dev_err(dev, "Unable to enable clock\n");
+		return rc;
+	}
+
 	mutex_init(&bt_bmc->mutex);
 	init_waitqueue_head(&bt_bmc->queue);
 
@@ -433,7 +445,7 @@ static int bt_bmc_probe(struct platform_device *pdev)
 	rc = misc_register(&bt_bmc->miscdev);
 	if (rc) {
 		dev_err(dev, "Unable to register misc device\n");
-		return rc;
+		goto err;
 	}
 
 	bt_bmc_config_irq(bt_bmc, pdev);
@@ -457,6 +469,11 @@ static int bt_bmc_probe(struct platform_device *pdev)
 	clr_b_busy(bt_bmc);
 
 	return 0;
+
+err:
+	clk_disable_unprepare(bt_bmc->clk);
+
+	return rc;
 }
 
 static int bt_bmc_remove(struct platform_device *pdev)
@@ -466,6 +483,8 @@ static int bt_bmc_remove(struct platform_device *pdev)
 	misc_deregister(&bt_bmc->miscdev);
 	if (bt_bmc->irq < 0)
 		del_timer_sync(&bt_bmc->poll_timer);
+	clk_disable_unprepare(bt_bmc->clk);
+
 	return 0;
 }
 
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/6] ARM: dts: aspeed: add LCLK setting into LPC KCS nodes

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property setting into LPC
KCS node as one of required properties to enable the LCLK by the
LPC KCS driver.

Note: dtbs should be re-compiled after applying this change since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
 * No change.

 arch/arm/boot/dts/aspeed-g5.dtsi | 4 ++++
 arch/arm/boot/dts/aspeed-g6.dtsi | 4 ++++
 2 files changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index d0cc4be2de59..7495f93c5069 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -446,6 +446,7 @@ kcs1: kcs@24 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -453,6 +454,7 @@ kcs2: kcs@28 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -460,6 +462,7 @@ kcs3: kcs@2c {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -467,6 +470,7 @@ kcs4: kcs@114 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index 465c3549fdc3..891b862363a7 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -520,6 +520,7 @@ kcs1: kcs@24 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
 					interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					kcs_chan = <1>;
 					status = "disabled";
 				};
@@ -528,6 +529,7 @@ kcs2: kcs@28 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
 					interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -535,6 +537,7 @@ kcs3: kcs@2c {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
 					interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -542,6 +545,7 @@ kcs4: kcs@114 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
 					interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
-- 
2.25.1

[PATCH v3 4/6] ARM: dts: aspeed: add LCLK setting into LPC KCS nodes

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property setting into LPC
KCS node as one of required properties to enable the LCLK by the
LPC KCS driver.

Note: dtbs should be re-compiled after applying this change since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
 * No change.

 arch/arm/boot/dts/aspeed-g5.dtsi | 4 ++++
 arch/arm/boot/dts/aspeed-g6.dtsi | 4 ++++
 2 files changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index d0cc4be2de59..7495f93c5069 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -446,6 +446,7 @@ kcs1: kcs@24 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -453,6 +454,7 @@ kcs2: kcs@28 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -460,6 +462,7 @@ kcs3: kcs@2c {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -467,6 +470,7 @@ kcs4: kcs@114 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index 465c3549fdc3..891b862363a7 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -520,6 +520,7 @@ kcs1: kcs@24 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
 					interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					kcs_chan = <1>;
 					status = "disabled";
 				};
@@ -528,6 +529,7 @@ kcs2: kcs@28 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
 					interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -535,6 +537,7 @@ kcs3: kcs@2c {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
 					interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -542,6 +545,7 @@ kcs4: kcs@114 {
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
 					interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 5/6] dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property as one of
required properties to enable the LCLK by the LPC KCS driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
Changes sinve v1:
 * Added 'clocks' property into kcs-bmc bindings using
   'aspeed,ast2400-kcs-bmc.yaml' because it's not merged into
   'aspeed-lpc.yaml' yet. The bindings merging could be done using a
   separate patch later.

 .../devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml   | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
index 4ff6fabfcb30..92ec0da047f4 100644
--- a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
+++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
@@ -71,9 +71,14 @@ properties:
     $ref: '/schemas/types.yaml#/definitions/uint32'
     description: The host CPU IO map address
 
+  clocks:
+    maxItems: 1
+    description: Reference clock for the LPC controller
+
 required:
   - compatible
   - interrupts
+  - clocks
 
 additionalProperties: false
 
@@ -96,6 +101,7 @@ allOf:
 
 examples:
   - |
+    #include <dt-bindings/clock/aspeed-clock.h>
     #include <dt-bindings/interrupt-controller/irq.h>
     kcs3: kcs@24 {
         compatible = "aspeed,ast2600-kcs-bmc";
@@ -103,4 +109,5 @@ examples:
         aspeed,lpc-io-reg = <0xca2>;
         aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
         interrupts = <8>;
+        clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
     };
-- 
2.25.1

[PATCH v3 5/6] dt-bindings: ipmi: aspeed, kcs-bmc: add 'clocks' as a required property

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
hardware block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds 'clocks' property as one of
required properties to enable the LCLK by the LPC KCS driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise the driver will not
be probed correctly.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
---
v2 -> v3:
 * Made commit message more descriptive.

v1 -> v2:
Changes sinve v1:
 * Added 'clocks' property into kcs-bmc bindings using
   'aspeed,ast2400-kcs-bmc.yaml' because it's not merged into
   'aspeed-lpc.yaml' yet. The bindings merging could be done using a
   separate patch later.

 .../devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml   | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
index 4ff6fabfcb30..92ec0da047f4 100644
--- a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
+++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml
@@ -71,9 +71,14 @@ properties:
     $ref: '/schemas/types.yaml#/definitions/uint32'
     description: The host CPU IO map address
 
+  clocks:
+    maxItems: 1
+    description: Reference clock for the LPC controller
+
 required:
   - compatible
   - interrupts
+  - clocks
 
 additionalProperties: false
 
@@ -96,6 +101,7 @@ allOf:
 
 examples:
   - |
+    #include <dt-bindings/clock/aspeed-clock.h>
     #include <dt-bindings/interrupt-controller/irq.h>
     kcs3: kcs@24 {
         compatible = "aspeed,ast2600-kcs-bmc";
@@ -103,4 +109,5 @@ examples:
         aspeed,lpc-io-reg = <0xca2>;
         aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
         interrupts = <8>;
+        clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
     };
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 6/6] ipmi: kcs_bmc_aspeed: add clock control logic

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC KCS driver is registered ahead of lpc-ctrl module, LPC
KCS block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds clock control logic into the LPC
KCS driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise this driver will not
be probed correctly.

Fixes: be2ed207e374 ("ipmi: add an Aspeed KCS IPMI BMC driver")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
---
v2 -> v3:
 * Simplified the -EPROBE_DEFER handling using dev_err_probe().

v1 -> v2:
 * No change.

 drivers/char/ipmi/kcs_bmc_aspeed.c | 28 ++++++++++++++++++++++++----
 1 file changed, 24 insertions(+), 4 deletions(-)

diff --git a/drivers/char/ipmi/kcs_bmc_aspeed.c b/drivers/char/ipmi/kcs_bmc_aspeed.c
index 92a37b33494c..66c9f51ae611 100644
--- a/drivers/char/ipmi/kcs_bmc_aspeed.c
+++ b/drivers/char/ipmi/kcs_bmc_aspeed.c
@@ -6,6 +6,7 @@
 #define pr_fmt(fmt) "aspeed-kcs-bmc: " fmt
 
 #include <linux/atomic.h>
+#include <linux/clk.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
@@ -126,6 +127,8 @@ struct aspeed_kcs_bmc {
 		bool remove;
 		struct timer_list timer;
 	} obe;
+
+	struct clk *clk;
 };
 
 struct aspeed_kcs_of_ops {
@@ -620,24 +623,34 @@ static int aspeed_kcs_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(priv->clk),
+				     "Couldn't get clock\n");
+	rc = clk_prepare_enable(priv->clk);
+	if (rc) {
+		dev_err(&pdev->dev, "Couldn't enable clock\n");
+		return rc;
+	}
+
 	spin_lock_init(&priv->obe.lock);
 	priv->obe.remove = false;
 	timer_setup(&priv->obe.timer, aspeed_kcs_check_obe, 0);
 
 	rc = aspeed_kcs_set_address(kcs_bmc, addrs, nr_addrs);
 	if (rc)
-		return rc;
+		goto err;
 
 	/* Host to BMC IRQ */
 	rc = aspeed_kcs_config_downstream_irq(kcs_bmc, pdev);
 	if (rc)
-		return rc;
+		goto err;
 
 	/* BMC to Host IRQ */
 	if (have_upstream_irq) {
 		rc = aspeed_kcs_config_upstream_irq(priv, upstream_irq[0], upstream_irq[1]);
 		if (rc < 0)
-			return rc;
+			goto err;
 	} else {
 		priv->upstream_irq.mode = aspeed_kcs_irq_none;
 	}
@@ -650,13 +663,19 @@ static int aspeed_kcs_probe(struct platform_device *pdev)
 	rc = kcs_bmc_add_device(&priv->kcs_bmc);
 	if (rc) {
 		dev_warn(&pdev->dev, "Failed to register channel %d: %d\n", kcs_bmc->channel, rc);
-		return rc;
+		goto err;
 	}
 
 	dev_info(&pdev->dev, "Initialised channel %d at 0x%x\n",
 			kcs_bmc->channel, addrs[0]);
 
 	return 0;
+
+err:
+	aspeed_kcs_enable_channel(kcs_bmc, false);
+	clk_disable_unprepare(priv->clk);
+
+	return rc;
 }
 
 static int aspeed_kcs_remove(struct platform_device *pdev)
@@ -664,6 +683,7 @@ static int aspeed_kcs_remove(struct platform_device *pdev)
 	struct aspeed_kcs_bmc *priv = platform_get_drvdata(pdev);
 	struct kcs_bmc_device *kcs_bmc = &priv->kcs_bmc;
 
+	clk_disable_unprepare(priv->clk);
 	kcs_bmc_remove_device(kcs_bmc);
 
 	aspeed_kcs_enable_channel(kcs_bmc, false);
-- 
2.25.1

[PATCH v3 6/6] ipmi: kcs_bmc_aspeed: add clock control logic

[jae.hyun.yoo]

From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>

If LPC KCS driver is registered ahead of lpc-ctrl module, LPC
KCS block will be enabled without heart beating of LCLK until
lpc-ctrl enables the LCLK. This issue causes improper handling on
host interrupts when the host sends interrupts in that time frame.
Then kernel eventually forcibly disables the interrupt with
dumping stack and printing a 'nobody cared this irq' message out.

To prevent this issue, all LPC sub drivers should enable LCLK
individually so this patch adds clock control logic into the LPC
KCS driver.

Note: dtsi change in this patch series should be applied along with,
and dtbs should be re-compiled after applying this series since
it's adding a new required property otherwise this driver will not
be probed correctly.

Fixes: be2ed207e374 ("ipmi: add an Aspeed KCS IPMI BMC driver")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
---
v2 -> v3:
 * Simplified the -EPROBE_DEFER handling using dev_err_probe().

v1 -> v2:
 * No change.

 drivers/char/ipmi/kcs_bmc_aspeed.c | 28 ++++++++++++++++++++++++----
 1 file changed, 24 insertions(+), 4 deletions(-)

diff --git a/drivers/char/ipmi/kcs_bmc_aspeed.c b/drivers/char/ipmi/kcs_bmc_aspeed.c
index 92a37b33494c..66c9f51ae611 100644
--- a/drivers/char/ipmi/kcs_bmc_aspeed.c
+++ b/drivers/char/ipmi/kcs_bmc_aspeed.c
@@ -6,6 +6,7 @@
 #define pr_fmt(fmt) "aspeed-kcs-bmc: " fmt
 
 #include <linux/atomic.h>
+#include <linux/clk.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
@@ -126,6 +127,8 @@ struct aspeed_kcs_bmc {
 		bool remove;
 		struct timer_list timer;
 	} obe;
+
+	struct clk *clk;
 };
 
 struct aspeed_kcs_of_ops {
@@ -620,24 +623,34 @@ static int aspeed_kcs_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(priv->clk),
+				     "Couldn't get clock\n");
+	rc = clk_prepare_enable(priv->clk);
+	if (rc) {
+		dev_err(&pdev->dev, "Couldn't enable clock\n");
+		return rc;
+	}
+
 	spin_lock_init(&priv->obe.lock);
 	priv->obe.remove = false;
 	timer_setup(&priv->obe.timer, aspeed_kcs_check_obe, 0);
 
 	rc = aspeed_kcs_set_address(kcs_bmc, addrs, nr_addrs);
 	if (rc)
-		return rc;
+		goto err;
 
 	/* Host to BMC IRQ */
 	rc = aspeed_kcs_config_downstream_irq(kcs_bmc, pdev);
 	if (rc)
-		return rc;
+		goto err;
 
 	/* BMC to Host IRQ */
 	if (have_upstream_irq) {
 		rc = aspeed_kcs_config_upstream_irq(priv, upstream_irq[0], upstream_irq[1]);
 		if (rc < 0)
-			return rc;
+			goto err;
 	} else {
 		priv->upstream_irq.mode = aspeed_kcs_irq_none;
 	}
@@ -650,13 +663,19 @@ static int aspeed_kcs_probe(struct platform_device *pdev)
 	rc = kcs_bmc_add_device(&priv->kcs_bmc);
 	if (rc) {
 		dev_warn(&pdev->dev, "Failed to register channel %d: %d\n", kcs_bmc->channel, rc);
-		return rc;
+		goto err;
 	}
 
 	dev_info(&pdev->dev, "Initialised channel %d at 0x%x\n",
 			kcs_bmc->channel, addrs[0]);
 
 	return 0;
+
+err:
+	aspeed_kcs_enable_channel(kcs_bmc, false);
+	clk_disable_unprepare(priv->clk);
+
+	return rc;
 }
 
 static int aspeed_kcs_remove(struct platform_device *pdev)
@@ -664,6 +683,7 @@ static int aspeed_kcs_remove(struct platform_device *pdev)
 	struct aspeed_kcs_bmc *priv = platform_get_drvdata(pdev);
 	struct kcs_bmc_device *kcs_bmc = &priv->kcs_bmc;
 
+	clk_disable_unprepare(priv->clk);
 	kcs_bmc_remove_device(kcs_bmc);
 
 	aspeed_kcs_enable_channel(kcs_bmc, false);
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/6] dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property

[Rob Herring]

On Mon, 08 Nov 2021 11:01:56 -0800, jae.hyun.yoo@intel.com wrote:
> From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> 
> If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
> hardware block will be enabled without heart beating of LCLK until
> lpc-ctrl enables the LCLK. This issue causes improper handling on
> host interrupts when the host sends interrupts in that time frame.
> Then kernel eventually forcibly disables the interrupt with
> dumping stack and printing a 'nobody cared this irq' message out.
> 
> To prevent this issue, all LPC sub drivers should enable LCLK
> individually so this patch adds 'clocks' property as one of
> required properties to enable the LCLK by the LPC IBT driver.
> 
> Note: dtsi change in this patch series should be applied along with,
> and dtbs should be re-compiled after applying this series since
> it's adding a new required property otherwise the driver will not
> be probed correctly.
> 
> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> ---
> v2 -> v3:
>  * Made commit message more descriptive.
> 
> v1 -> v2:
>  * Added 'clocks' property into ibt bindings using
>    'aspeed,ast2400-ibt-bmc.txt' because it's not merged into
>    'aspeed-lpc.yaml' yet. The bindings merging could be done using a
>    separate patch later.
> 
>  .../devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt         | 2 ++
>  1 file changed, 2 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 2/6] dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property

[Rob Herring]

On Mon, 08 Nov 2021 11:01:56 -0800, jae.hyun.yoo@intel.com wrote:
> From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> 
> If LPC BT driver is registered ahead of lpc-ctrl module, LPC BT
> hardware block will be enabled without heart beating of LCLK until
> lpc-ctrl enables the LCLK. This issue causes improper handling on
> host interrupts when the host sends interrupts in that time frame.
> Then kernel eventually forcibly disables the interrupt with
> dumping stack and printing a 'nobody cared this irq' message out.
> 
> To prevent this issue, all LPC sub drivers should enable LCLK
> individually so this patch adds 'clocks' property as one of
> required properties to enable the LCLK by the LPC IBT driver.
> 
> Note: dtsi change in this patch series should be applied along with,
> and dtbs should be re-compiled after applying this series since
> it's adding a new required property otherwise the driver will not
> be probed correctly.
> 
> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> ---
> v2 -> v3:
>  * Made commit message more descriptive.
> 
> v1 -> v2:
>  * Added 'clocks' property into ibt bindings using
>    'aspeed,ast2400-ibt-bmc.txt' because it's not merged into
>    'aspeed-lpc.yaml' yet. The bindings merging could be done using a
>    separate patch later.
> 
>  .../devicetree/bindings/ipmi/aspeed,ast2400-ibt-bmc.txt         | 2 ++
>  1 file changed, 2 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 5/6] dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property

[Rob Herring]

On Mon, 08 Nov 2021 11:01:59 -0800, jae.hyun.yoo@intel.com wrote:
> From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> 
> If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
> hardware block will be enabled without heart beating of LCLK until
> lpc-ctrl enables the LCLK. This issue causes improper handling on
> host interrupts when the host sends interrupts in that time frame.
> Then kernel eventually forcibly disables the interrupt with
> dumping stack and printing a 'nobody cared this irq' message out.
> 
> To prevent this issue, all LPC sub drivers should enable LCLK
> individually so this patch adds 'clocks' property as one of
> required properties to enable the LCLK by the LPC KCS driver.
> 
> Note: dtsi change in this patch series should be applied along with,
> and dtbs should be re-compiled after applying this series since
> it's adding a new required property otherwise the driver will not
> be probed correctly.
> 
> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> ---
> v2 -> v3:
>  * Made commit message more descriptive.
> 
> v1 -> v2:
> Changes sinve v1:
>  * Added 'clocks' property into kcs-bmc bindings using
>    'aspeed,ast2400-kcs-bmc.yaml' because it's not merged into
>    'aspeed-lpc.yaml' yet. The bindings merging could be done using a
>    separate patch later.
> 
>  .../devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml   | 7 +++++++
>  1 file changed, 7 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 5/6] dt-bindings: ipmi: aspeed,kcs-bmc: add 'clocks' as a required property

[Rob Herring]

On Mon, 08 Nov 2021 11:01:59 -0800, jae.hyun.yoo@intel.com wrote:
> From: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> 
> If LPC KCS driver is registered ahead of lpc-ctrl module, LPC KCS
> hardware block will be enabled without heart beating of LCLK until
> lpc-ctrl enables the LCLK. This issue causes improper handling on
> host interrupts when the host sends interrupts in that time frame.
> Then kernel eventually forcibly disables the interrupt with
> dumping stack and printing a 'nobody cared this irq' message out.
> 
> To prevent this issue, all LPC sub drivers should enable LCLK
> individually so this patch adds 'clocks' property as one of
> required properties to enable the LCLK by the LPC KCS driver.
> 
> Note: dtsi change in this patch series should be applied along with,
> and dtbs should be re-compiled after applying this series since
> it's adding a new required property otherwise the driver will not
> be probed correctly.
> 
> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
> ---
> v2 -> v3:
>  * Made commit message more descriptive.
> 
> v1 -> v2:
> Changes sinve v1:
>  * Added 'clocks' property into kcs-bmc bindings using
>    'aspeed,ast2400-kcs-bmc.yaml' because it's not merged into
>    'aspeed-lpc.yaml' yet. The bindings merging could be done using a
>    separate patch later.
> 
>  .../devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml   | 7 +++++++
>  1 file changed, 7 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel