> From: Deren Wu <deren.wu@mediatek.com>
> 
> When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
> fw for channel config. This would cause rx performance bad while
> monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
> get the same performance as normal channels.

Hi Deren,

> 
> Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
> Signed-off-by: Deren Wu <deren.wu@mediatek.com>
> ---
>  drivers/net/wireless/mediatek/mt76/mt7615/mcu.c | 3 ++-
>  drivers/net/wireless/mediatek/mt76/mt7915/mcu.c | 3 ++-
>  drivers/net/wireless/mediatek/mt76/mt7921/mcu.c | 3 ++-
>  3 files changed, 6 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
> index 390add3144c2..97e2a85cb728 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
> @@ -2151,7 +2151,8 @@ int mt7615_mcu_set_chan_info(struct mt7615_phy *phy, int cmd)
>  		.center_chan2 = ieee80211_frequency_to_channel(freq2),
>  	};
>  
> -	if (cmd == MCU_EXT_CMD(SET_RX_PATH))
> +	if (cmd == MCU_EXT_CMD(SET_RX_PATH) ||
> +	    dev->mt76.hw->conf.flags & IEEE80211_CONF_MONITOR)

is this patch compliant with 802.11h DFS standard?

Regards,
Lorenzo

>  		req.switch_reason = CH_SWITCH_NORMAL;
>  	else if (phy->mt76->hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
>  		req.switch_reason = CH_SWITCH_SCAN_BYPASS_DPD;
> diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
> index 10dc4bf5adec..c56d48342aaf 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
> @@ -2833,7 +2833,8 @@ int mt7915_mcu_set_chan_info(struct mt7915_phy *phy, int cmd)
>  	}
>  #endif
>  
> -	if (cmd == MCU_EXT_CMD(SET_RX_PATH))
> +	if (cmd == MCU_EXT_CMD(SET_RX_PATH) ||
> +	    dev->mt76.hw->conf.flags & IEEE80211_CONF_MONITOR)
>  		req.switch_reason = CH_SWITCH_NORMAL;
>  	else if (phy->mt76->hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
>  		req.switch_reason = CH_SWITCH_SCAN_BYPASS_DPD;
> diff --git a/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c
> index 5ef8b24f0ab3..da2be050ed7c 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt7921/mcu.c
> @@ -863,7 +863,8 @@ int mt7921_mcu_set_chan_info(struct mt7921_phy *phy, int cmd)
>  	else
>  		req.channel_band = chandef->chan->band;
>  
> -	if (cmd == MCU_EXT_CMD(SET_RX_PATH))
> +	if (cmd == MCU_EXT_CMD(SET_RX_PATH) ||
> +	    dev->mt76.hw->conf.flags & IEEE80211_CONF_MONITOR)
>  		req.switch_reason = CH_SWITCH_NORMAL;
>  	else if (dev->mt76.hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
>  		req.switch_reason = CH_SWITCH_SCAN_BYPASS_DPD;
> -- 
> 2.18.0
>