Re: [PATCHv2] mmc: block: Check for errors after write on SPI

[Andy Shevchenko <andriy.shevchenko@linux.intel.com>]

On Wed, Mar 23, 2022 at 02:12:43PM +0000, Christian Löhle wrote:
> Introduce a SEND_STATUS check for writes through SPI to not mark
> an unsuccessful write as successful.
> 
> Since SPI SD/MMC does not have states, after a write, the card will
> just hold the line LOW until it is ready again. The driver marks the
> write therefore as completed as soon as it reads something other than
> all zeroes.
> The driver does not distinguish from a card no longer signalling busy
> and it being disconnected (and the line being pulled-up by the host).
> This lead to writes being marked as successful when disconnecting
> a busy card.
> Now the card is ensured to be still connected by an additional CMD13,
> just like non-SPI is ensured to go back to TRAN state.
> 
> While at it and since we already poll for the post-write status anyway,
> we might as well check for SPIs error bits (any of them).
> 
> The disconnecting card problem is reproducable for me after continuous
> write activity and randomly disconnecting, around every 20-50 tries
> on SPI DS for some card.

LGTM, FWIW,
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

(Next time send a new version of the patch as a separate email thread,
 so tools won't mess with the different versions in one thread. I hope
 no need for resend this time and Ulf handles this)

> Fixes: 7213d175e3b6f ("MMC/SD card driver learns SPI")
> Cc: stable@vger.kernel.org
> Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
> ---
> v2:
>   - Reorder err and status check for err to take precedence and look cleaner
> 
>  drivers/mmc/core/block.c | 27 ++++++++++++++++++++++++++-
>  1 file changed, 26 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
> index 4e67c1403cc9..54c2009f398f 100644
> --- a/drivers/mmc/core/block.c
> +++ b/drivers/mmc/core/block.c
> @@ -1903,9 +1903,34 @@ static int mmc_blk_card_busy(struct mmc_card *card, struct request *req)
>  	struct mmc_blk_busy_data cb_data;
>  	int err;
> 
> -	if (mmc_host_is_spi(card->host) || rq_data_dir(req) == READ)
> +	if (rq_data_dir(req) == READ)
>  		return 0;
> 
> +	/*
> +	 * SPI does not have a TRAN state we have to wait on, instead the
> +	 * card is ready again when it no longer holds the line LOW.
> +	 * We still have to ensure two things here before we know the write
> +	 * was successful:
> +	 * 1. The card has not disconnected during busy and we actually read our
> +	 * own pull-up, thinking it was still connected, so ensure it
> +	 * still responds.
> +	 * 2. Check for any error bits, in particular R1_SPI_IDLE to catch a
> +	 * just reconnected card after being disconnected during busy.
> +	 */
> +	if (mmc_host_is_spi(card->host)) {
> +		u32 status = 0;
> +
> +		err = __mmc_send_status(card, &status, 0);
> +		/* All R1 and R2 bits of SPI are errors in our case */
> +		if (err || status) {
> +			mqrq->brq.data.bytes_xfered = 0;
> +			if (err)
> +				return err;
> +			return -EIO;
> +		}
> +		return 0;
> +	}
> +
>  	cb_data.card = card;
>  	cb_data.status = 0;
>  	err = __mmc_poll_for_busy(card->host, 0, MMC_BLK_TIMEOUT_MS,
> --
> 2.34.1
> Hyperstone GmbH | Reichenaustr. 39a  | 78467 Konstanz
> Managing Director: Dr. Jan Peter Berns.
> Commercial register of local courts: Freiburg HRB381782
> 

-- 
With Best Regards,
Andy Shevchenko