[v2 0/3] Add dtsi for sc7280 herobrine boards that using rt5682 codec

[v2 0/3] Add dtsi for sc7280 herobrine boards that using rt5682 codec

[Judy Hsiao]

Put sound node and lpass_cpu node settings for boards that use rt5682
codec in the sc7280-herobrine-audio-rt5682.dtsi as there are different
choices of headset codec for herobrine projects. Common audio setting
for the internal speaker is in sc7280-herobrine.dtsi.

This series depends on:
"Add lpass pin control support for audio on sc7280 based targets" [1]
"Add soundcard support for sc7280 based platforms" [2]

[1] https://patchwork.kernel.org/project/linux-arm-msm/list/?series=638776
[2] https://patchwork.kernel.org/project/linux-arm-msm/list/?series=643589

Changes Since V1:
    -- Remove sound-dai-cells in sound node.
    -- Add dependency list.
    -- Update patch subject.

Judy Hsiao (3):
  arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1
  arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi
  arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi
    in villager and herobrine-r1

 .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
 .../qcom/sc7280-herobrine-herobrine-r1.dts    |   1 +
 .../dts/qcom/sc7280-herobrine-villager-r0.dts |   1 +
 .../arm64/boot/dts/qcom/sc7280-herobrine.dtsi |  14 ++
 4 files changed, 136 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi

-- 
2.36.1.124.g0e6072fb45-goog

[v2 0/3] Add dtsi for sc7280 herobrine boards that using rt5682 codec

[Judy Hsiao]

Put sound node and lpass_cpu node settings for boards that use rt5682
codec in the sc7280-herobrine-audio-rt5682.dtsi as there are different
choices of headset codec for herobrine projects. Common audio setting
for the internal speaker is in sc7280-herobrine.dtsi.

This series depends on:
"Add lpass pin control support for audio on sc7280 based targets" [1]
"Add soundcard support for sc7280 based platforms" [2]

[1] https://patchwork.kernel.org/project/linux-arm-msm/list/?series=638776
[2] https://patchwork.kernel.org/project/linux-arm-msm/list/?series=643589

Changes Since V1:
    -- Remove sound-dai-cells in sound node.
    -- Add dependency list.
    -- Update patch subject.

Judy Hsiao (3):
  arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1
  arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi
  arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi
    in villager and herobrine-r1

 .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
 .../qcom/sc7280-herobrine-herobrine-r1.dts    |   1 +
 .../dts/qcom/sc7280-herobrine-villager-r0.dts |   1 +
 .../arm64/boot/dts/qcom/sc7280-herobrine.dtsi |  14 ++
 4 files changed, 136 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi

-- 
2.36.1.124.g0e6072fb45-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Judy Hsiao]

1. Add drive strength property for mi2s1 on sc7280 based platforms.
2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index 9cb1bc8ed6b5..6d8744e130b0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -612,6 +612,20 @@ &dp_hot_plug_det {
 	bias-disable;
 };
 
+&mi2s1_data0 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_sclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_ws {
+	drive-strength = <6>;
+};
+
 &pcie1_clkreq_n {
 	bias-pull-up;
 	drive-strength = <2>;
-- 
2.36.1.124.g0e6072fb45-goog

[v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Judy Hsiao]

1. Add drive strength property for mi2s1 on sc7280 based platforms.
2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index 9cb1bc8ed6b5..6d8744e130b0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -612,6 +612,20 @@ &dp_hot_plug_det {
 	bias-disable;
 };
 
+&mi2s1_data0 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_sclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_ws {
+	drive-strength = <6>;
+};
+
 &pcie1_clkreq_n {
 	bias-pull-up;
 	drive-strength = <2>;
-- 
2.36.1.124.g0e6072fb45-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Matthias Kaehlcke]

On Fri, May 20, 2022 at 04:10:02PM +0000, Judy Hsiao wrote:
> 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.
> 
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Matthias Kaehlcke]

On Fri, May 20, 2022 at 04:10:02PM +0000, Judy Hsiao wrote:
> 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.
> 
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Stephen Boyd]

Quoting Judy Hsiao (2022-05-20 09:10:02)
> 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.

s/Disbale/Disable/

The commit text is a list of things done but no reason why they're done.
I'd appreciate more freeform text with a blurb why a drive strength is
chosen and why pulls are disabled.

> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> index 9cb1bc8ed6b5..6d8744e130b0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> @@ -612,6 +612,20 @@ &dp_hot_plug_det {
>         bias-disable;
>  };
>
> +&mi2s1_data0 {
> +       drive-strength = <6>;
> +       bias-disable;

Is there an external pull on this line?

> +};
> +
> +&mi2s1_sclk {
> +       drive-strength = <6>;
> +       bias-disable;

Is there an external pull on this line? If so please add that details as
a comment like we do for other external pulls.

> +};

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Stephen Boyd]

Quoting Judy Hsiao (2022-05-20 09:10:02)
> 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.

s/Disbale/Disable/

The commit text is a list of things done but no reason why they're done.
I'd appreciate more freeform text with a blurb why a drive strength is
chosen and why pulls are disabled.

> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> index 9cb1bc8ed6b5..6d8744e130b0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> @@ -612,6 +612,20 @@ &dp_hot_plug_det {
>         bias-disable;
>  };
>
> +&mi2s1_data0 {
> +       drive-strength = <6>;
> +       bias-disable;

Is there an external pull on this line?

> +};
> +
> +&mi2s1_sclk {
> +       drive-strength = <6>;
> +       bias-disable;

Is there an external pull on this line? If so please add that details as
a comment like we do for other external pulls.

> +};

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 1:38 PM Stephen Boyd <swboyd@chromium.org> wrote:
>
> Quoting Judy Hsiao (2022-05-20 09:10:02)
> > 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> > 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.
>
> s/Disbale/Disable/
>
> The commit text is a list of things done but no reason why they're done.
> I'd appreciate more freeform text with a blurb why a drive strength is
> chosen and why pulls are disabled.
>
> > Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
> >  1 file changed, 14 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> > index 9cb1bc8ed6b5..6d8744e130b0 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> > @@ -612,6 +612,20 @@ &dp_hot_plug_det {
> >         bias-disable;
> >  };
> >
> > +&mi2s1_data0 {
> > +       drive-strength = <6>;
> > +       bias-disable;
>
> Is there an external pull on this line?
>
> > +};
> > +
> > +&mi2s1_sclk {
> > +       drive-strength = <6>;
> > +       bias-disable;
>
> Is there an external pull on this line? If so please add that details as
> a comment like we do for other external pulls.

Actually, I think they are output lines, which is why they have a
drive-strength. I think for output lines we don't usually comment
about why we're disabling the pulls, only for input lines?

-Doug

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 1:38 PM Stephen Boyd <swboyd@chromium.org> wrote:
>
> Quoting Judy Hsiao (2022-05-20 09:10:02)
> > 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> > 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.
>
> s/Disbale/Disable/
>
> The commit text is a list of things done but no reason why they're done.
> I'd appreciate more freeform text with a blurb why a drive strength is
> chosen and why pulls are disabled.
>
> > Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
> >  1 file changed, 14 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> > index 9cb1bc8ed6b5..6d8744e130b0 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> > @@ -612,6 +612,20 @@ &dp_hot_plug_det {
> >         bias-disable;
> >  };
> >
> > +&mi2s1_data0 {
> > +       drive-strength = <6>;
> > +       bias-disable;
>
> Is there an external pull on this line?
>
> > +};
> > +
> > +&mi2s1_sclk {
> > +       drive-strength = <6>;
> > +       bias-disable;
>
> Is there an external pull on this line? If so please add that details as
> a comment like we do for other external pulls.

Actually, I think they are output lines, which is why they have a
drive-strength. I think for output lines we don't usually comment
about why we're disabling the pulls, only for input lines?

-Doug

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Stephen Boyd]

Quoting Doug Anderson (2022-05-20 13:39:21)
> On Fri, May 20, 2022 at 1:38 PM Stephen Boyd <swboyd@chromium.org> wrote:
> >
> > Quoting Judy Hsiao (2022-05-20 09:10:02)
> > > +};
> > > +
> > > +&mi2s1_sclk {
> > > +       drive-strength = <6>;
> > > +       bias-disable;
> >
> > Is there an external pull on this line? If so please add that details as
> > a comment like we do for other external pulls.
>
> Actually, I think they are output lines, which is why they have a
> drive-strength. I think for output lines we don't usually comment
> about why we're disabling the pulls, only for input lines?

Ok makes sense. Even for an open drain signal it would be an "input" so
that rule still applies?

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Stephen Boyd]

Quoting Doug Anderson (2022-05-20 13:39:21)
> On Fri, May 20, 2022 at 1:38 PM Stephen Boyd <swboyd@chromium.org> wrote:
> >
> > Quoting Judy Hsiao (2022-05-20 09:10:02)
> > > +};
> > > +
> > > +&mi2s1_sclk {
> > > +       drive-strength = <6>;
> > > +       bias-disable;
> >
> > Is there an external pull on this line? If so please add that details as
> > a comment like we do for other external pulls.
>
> Actually, I think they are output lines, which is why they have a
> drive-strength. I think for output lines we don't usually comment
> about why we're disabling the pulls, only for input lines?

Ok makes sense. Even for an open drain signal it would be an "input" so
that rule still applies?

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 2:01 PM Stephen Boyd <swboyd@chromium.org> wrote:
>
> Quoting Doug Anderson (2022-05-20 13:39:21)
> > On Fri, May 20, 2022 at 1:38 PM Stephen Boyd <swboyd@chromium.org> wrote:
> > >
> > > Quoting Judy Hsiao (2022-05-20 09:10:02)
> > > > +};
> > > > +
> > > > +&mi2s1_sclk {
> > > > +       drive-strength = <6>;
> > > > +       bias-disable;
> > >
> > > Is there an external pull on this line? If so please add that details as
> > > a comment like we do for other external pulls.
> >
> > Actually, I think they are output lines, which is why they have a
> > drive-strength. I think for output lines we don't usually comment
> > about why we're disabling the pulls, only for input lines?
>
> Ok makes sense. Even for an open drain signal it would be an "input" so
> that rule still applies?

I think open drain is mostly used for bidirectional signals, like i2c
lines. In that case then you're right, you can have a drive-strength
and a pull. ...I thought i2s was not bidirectoinal and not open-drain,
but I certainly could be wrong.

-Doug

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 2:01 PM Stephen Boyd <swboyd@chromium.org> wrote:
>
> Quoting Doug Anderson (2022-05-20 13:39:21)
> > On Fri, May 20, 2022 at 1:38 PM Stephen Boyd <swboyd@chromium.org> wrote:
> > >
> > > Quoting Judy Hsiao (2022-05-20 09:10:02)
> > > > +};
> > > > +
> > > > +&mi2s1_sclk {
> > > > +       drive-strength = <6>;
> > > > +       bias-disable;
> > >
> > > Is there an external pull on this line? If so please add that details as
> > > a comment like we do for other external pulls.
> >
> > Actually, I think they are output lines, which is why they have a
> > drive-strength. I think for output lines we don't usually comment
> > about why we're disabling the pulls, only for input lines?
>
> Ok makes sense. Even for an open drain signal it would be an "input" so
> that rule still applies?

I think open drain is mostly used for bidirectional signals, like i2c
lines. In that case then you're right, you can have a drive-strength
and a pull. ...I thought i2s was not bidirectoinal and not open-drain,
but I certainly could be wrong.

-Doug

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 9:10 AM Judy Hsiao <judyhsiao@chromium.org> wrote:
>
> 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.
>
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> index 9cb1bc8ed6b5..6d8744e130b0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> @@ -612,6 +612,20 @@ &dp_hot_plug_det {
>         bias-disable;
>  };
>
> +&mi2s1_data0 {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s1_sclk {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s1_ws {
> +       drive-strength = <6>;
> +};

I'm actually curious why this line has a drive-strength but _no_ bias
setting. I guess I should figure out what the heck "ws" is. Ah, I
guess it is word select.

Since this is an output I'd expect to see "bias-disable" here too.

-Doug

Re: [v2 1/3] arm64: dts: qcom: sc7280: herobrine: Add pinconf settings for mi2s1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 9:10 AM Judy Hsiao <judyhsiao@chromium.org> wrote:
>
> 1. Add drive strength property for mi2s1 on sc7280 based platforms.
> 2. Disbale the pull-up mi2s1_data0, mi2s1_sclk.
>
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> index 9cb1bc8ed6b5..6d8744e130b0 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
> @@ -612,6 +612,20 @@ &dp_hot_plug_det {
>         bias-disable;
>  };
>
> +&mi2s1_data0 {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s1_sclk {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s1_ws {
> +       drive-strength = <6>;
> +};

I'm actually curious why this line has a drive-strength but _no_ bias
setting. I guess I should figure out what the heck "ws" is. Ah, I
guess it is word select.

Since this is an output I'd expect to see "bias-disable" here too.

-Doug

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[v2 2/3] arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi

[Judy Hsiao]

Audio dtsi for sc7280 boards that using rt5682 headset codec:
1. Add dt nodes for sound card which use I2S playback and record
   through rt5682s and I2S playback through max98357a.
2. Enable lpass cpu node and add pin control and dai-links.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
---
 .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
 1 file changed, 120 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
new file mode 100644
index 000000000000..d83e99f1d417
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ *
+ * This file defines the common audio settings for the child boards using rt5682 codec.
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/ {
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+	sound: sound {
+		compatible = "google,sc7280-herobrine";
+		model = "sc7280-rt5682-max98360a-1mic";
+
+		status = "okay";
+		audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		dai-link@0 {
+			link-name = "MAX98360";
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_SECONDARY>;
+			};
+
+			codec {
+				sound-dai = <&max98360a>;
+			};
+		};
+
+		dai-link@1 {
+			link-name = "ALC5682";
+			reg = <1>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_PRIMARY>;
+			};
+
+			codec {
+				sound-dai = <&alc5682 0 /* aif1 */>;
+			};
+		};
+	};
+};
+
+hp_i2c: &i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	alc5682: codec@1a {
+		compatible = "realtek,rt5682s";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_irq>;
+
+		#sound-dai-cells = <1>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <101 IRQ_TYPE_EDGE_BOTH>;
+
+		AVDD-supply = <&pp1800_alc5682>;
+		MICVDD-supply = <&pp3300_codec>;
+
+		realtek,dmic1-data-pin = <1>;
+		realtek,dmic1-clk-pin = <2>;
+		realtek,jd-src = <1>;
+		realtek,dmic-clk-rate-hz = <2048000>;
+	};
+};
+
+&lpass_cpu {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mi2s0_data0 &mi2s0_data1 &mi2s0_mclk &mi2s0_sclk &mi2s0_ws
+		     &mi2s1_data0 &mi2s1_sclk &mi2s1_ws>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	dai-link@0 {
+		reg = <MI2S_PRIMARY>;
+		qcom,playback-sd-lines = <1>;
+		qcom,capture-sd-lines = <0>;
+	};
+
+	dai-link@1 {
+		reg = <MI2S_SECONDARY>;
+		qcom,playback-sd-lines = <0>;
+	};
+};
+
+&mi2s0_data0 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_data1 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_mclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_sclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_ws {
+	drive-strength = <6>;
+};
-- 
2.36.1.124.g0e6072fb45-goog

[v2 2/3] arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi

[Judy Hsiao]

Audio dtsi for sc7280 boards that using rt5682 headset codec:
1. Add dt nodes for sound card which use I2S playback and record
   through rt5682s and I2S playback through max98357a.
2. Enable lpass cpu node and add pin control and dai-links.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
---
 .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
 1 file changed, 120 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
new file mode 100644
index 000000000000..d83e99f1d417
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ *
+ * This file defines the common audio settings for the child boards using rt5682 codec.
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/ {
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+	sound: sound {
+		compatible = "google,sc7280-herobrine";
+		model = "sc7280-rt5682-max98360a-1mic";
+
+		status = "okay";
+		audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		dai-link@0 {
+			link-name = "MAX98360";
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_SECONDARY>;
+			};
+
+			codec {
+				sound-dai = <&max98360a>;
+			};
+		};
+
+		dai-link@1 {
+			link-name = "ALC5682";
+			reg = <1>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_PRIMARY>;
+			};
+
+			codec {
+				sound-dai = <&alc5682 0 /* aif1 */>;
+			};
+		};
+	};
+};
+
+hp_i2c: &i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	alc5682: codec@1a {
+		compatible = "realtek,rt5682s";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_irq>;
+
+		#sound-dai-cells = <1>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <101 IRQ_TYPE_EDGE_BOTH>;
+
+		AVDD-supply = <&pp1800_alc5682>;
+		MICVDD-supply = <&pp3300_codec>;
+
+		realtek,dmic1-data-pin = <1>;
+		realtek,dmic1-clk-pin = <2>;
+		realtek,jd-src = <1>;
+		realtek,dmic-clk-rate-hz = <2048000>;
+	};
+};
+
+&lpass_cpu {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mi2s0_data0 &mi2s0_data1 &mi2s0_mclk &mi2s0_sclk &mi2s0_ws
+		     &mi2s1_data0 &mi2s1_sclk &mi2s1_ws>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	dai-link@0 {
+		reg = <MI2S_PRIMARY>;
+		qcom,playback-sd-lines = <1>;
+		qcom,capture-sd-lines = <0>;
+	};
+
+	dai-link@1 {
+		reg = <MI2S_SECONDARY>;
+		qcom,playback-sd-lines = <0>;
+	};
+};
+
+&mi2s0_data0 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_data1 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_mclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_sclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s0_ws {
+	drive-strength = <6>;
+};
-- 
2.36.1.124.g0e6072fb45-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 2/3] arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi

[Matthias Kaehlcke]

On Fri, May 20, 2022 at 04:10:03PM +0000, Judy Hsiao wrote:
> Audio dtsi for sc7280 boards that using rt5682 headset codec:
> 1. Add dt nodes for sound card which use I2S playback and record
>    through rt5682s and I2S playback through max98357a.
> 2. Enable lpass cpu node and add pin control and dai-links.
> 
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
>  1 file changed, 120 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> new file mode 100644
> index 000000000000..d83e99f1d417
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + *
> + * This file defines the common audio settings for the child boards using rt5682 codec.
> + *
> + * Copyright 2022 Google LLC.
> + */
> +
> +/ {
> +	/* BOARD-SPECIFIC TOP LEVEL NODES */
> +	sound: sound {

nit: the label might not be needed, unless we expect board files to override
settings. But well, there is also nothing inherently wrong with having it :)

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [v2 2/3] arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi

[Matthias Kaehlcke]

On Fri, May 20, 2022 at 04:10:03PM +0000, Judy Hsiao wrote:
> Audio dtsi for sc7280 boards that using rt5682 headset codec:
> 1. Add dt nodes for sound card which use I2S playback and record
>    through rt5682s and I2S playback through max98357a.
> 2. Enable lpass cpu node and add pin control and dai-links.
> 
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
>  1 file changed, 120 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> new file mode 100644
> index 000000000000..d83e99f1d417
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + *
> + * This file defines the common audio settings for the child boards using rt5682 codec.
> + *
> + * Copyright 2022 Google LLC.
> + */
> +
> +/ {
> +	/* BOARD-SPECIFIC TOP LEVEL NODES */
> +	sound: sound {

nit: the label might not be needed, unless we expect board files to override
settings. But well, there is also nothing inherently wrong with having it :)

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 2/3] arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 9:10 AM Judy Hsiao <judyhsiao@chromium.org> wrote:
>
> Audio dtsi for sc7280 boards that using rt5682 headset codec:
> 1. Add dt nodes for sound card which use I2S playback and record
>    through rt5682s and I2S playback through max98357a.
> 2. Enable lpass cpu node and add pin control and dai-links.
>
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
>  1 file changed, 120 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> new file mode 100644
> index 000000000000..d83e99f1d417
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + *
> + * This file defines the common audio settings for the child boards using rt5682 codec.
> + *
> + * Copyright 2022 Google LLC.
> + */
> +
> +/ {
> +       /* BOARD-SPECIFIC TOP LEVEL NODES */
> +       sound: sound {
> +               compatible = "google,sc7280-herobrine";
> +               model = "sc7280-rt5682-max98360a-1mic";
> +
> +               status = "okay";
> +               audio-routing =
> +                       "Headphone Jack", "HPOL",
> +                       "Headphone Jack", "HPOR";
> +
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               dai-link@0 {
> +                       link-name = "MAX98360";
> +                       reg = <0>;
> +
> +                       cpu {
> +                               sound-dai = <&lpass_cpu MI2S_SECONDARY>;
> +                       };
> +
> +                       codec {
> +                               sound-dai = <&max98360a>;
> +                       };
> +               };
> +
> +               dai-link@1 {
> +                       link-name = "ALC5682";
> +                       reg = <1>;
> +
> +                       cpu {
> +                               sound-dai = <&lpass_cpu MI2S_PRIMARY>;
> +                       };
> +
> +                       codec {
> +                               sound-dai = <&alc5682 0 /* aif1 */>;
> +                       };
> +               };
> +       };
> +};
> +
> +hp_i2c: &i2c2 {
> +       status = "okay";
> +       clock-frequency = <400000>;
> +
> +       alc5682: codec@1a {
> +               compatible = "realtek,rt5682s";
> +               reg = <0x1a>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&hp_irq>;
> +
> +               #sound-dai-cells = <1>;
> +
> +               interrupt-parent = <&tlmm>;
> +               interrupts = <101 IRQ_TYPE_EDGE_BOTH>;
> +
> +               AVDD-supply = <&pp1800_alc5682>;
> +               MICVDD-supply = <&pp3300_codec>;
> +
> +               realtek,dmic1-data-pin = <1>;
> +               realtek,dmic1-clk-pin = <2>;
> +               realtek,jd-src = <1>;
> +               realtek,dmic-clk-rate-hz = <2048000>;
> +       };
> +};
> +
> +&lpass_cpu {
> +       status = "okay";
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mi2s0_data0 &mi2s0_data1 &mi2s0_mclk &mi2s0_sclk &mi2s0_ws
> +                    &mi2s1_data0 &mi2s1_sclk &mi2s1_ws>;
> +
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
> +       dai-link@0 {
> +               reg = <MI2S_PRIMARY>;
> +               qcom,playback-sd-lines = <1>;
> +               qcom,capture-sd-lines = <0>;
> +       };
> +
> +       dai-link@1 {
> +               reg = <MI2S_SECONDARY>;
> +               qcom,playback-sd-lines = <0>;
> +       };
> +};
> +
> +&mi2s0_data0 {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_data1 {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_mclk {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_sclk {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_ws {
> +       drive-strength = <6>;

Just like for patch #1, I think you want "bias-disable" here, too.

-Doug

Re: [v2 2/3] arm64: dts: qcom: sc7280: Add sc7280-herobrine-audio-rt5682.dtsi

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 9:10 AM Judy Hsiao <judyhsiao@chromium.org> wrote:
>
> Audio dtsi for sc7280 boards that using rt5682 headset codec:
> 1. Add dt nodes for sound card which use I2S playback and record
>    through rt5682s and I2S playback through max98357a.
> 2. Enable lpass cpu node and add pin control and dai-links.
>
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  .../qcom/sc7280-herobrine-audio-rt5682.dtsi   | 120 ++++++++++++++++++
>  1 file changed, 120 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> new file mode 100644
> index 000000000000..d83e99f1d417
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-rt5682.dtsi
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + *
> + * This file defines the common audio settings for the child boards using rt5682 codec.
> + *
> + * Copyright 2022 Google LLC.
> + */
> +
> +/ {
> +       /* BOARD-SPECIFIC TOP LEVEL NODES */
> +       sound: sound {
> +               compatible = "google,sc7280-herobrine";
> +               model = "sc7280-rt5682-max98360a-1mic";
> +
> +               status = "okay";
> +               audio-routing =
> +                       "Headphone Jack", "HPOL",
> +                       "Headphone Jack", "HPOR";
> +
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               dai-link@0 {
> +                       link-name = "MAX98360";
> +                       reg = <0>;
> +
> +                       cpu {
> +                               sound-dai = <&lpass_cpu MI2S_SECONDARY>;
> +                       };
> +
> +                       codec {
> +                               sound-dai = <&max98360a>;
> +                       };
> +               };
> +
> +               dai-link@1 {
> +                       link-name = "ALC5682";
> +                       reg = <1>;
> +
> +                       cpu {
> +                               sound-dai = <&lpass_cpu MI2S_PRIMARY>;
> +                       };
> +
> +                       codec {
> +                               sound-dai = <&alc5682 0 /* aif1 */>;
> +                       };
> +               };
> +       };
> +};
> +
> +hp_i2c: &i2c2 {
> +       status = "okay";
> +       clock-frequency = <400000>;
> +
> +       alc5682: codec@1a {
> +               compatible = "realtek,rt5682s";
> +               reg = <0x1a>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&hp_irq>;
> +
> +               #sound-dai-cells = <1>;
> +
> +               interrupt-parent = <&tlmm>;
> +               interrupts = <101 IRQ_TYPE_EDGE_BOTH>;
> +
> +               AVDD-supply = <&pp1800_alc5682>;
> +               MICVDD-supply = <&pp3300_codec>;
> +
> +               realtek,dmic1-data-pin = <1>;
> +               realtek,dmic1-clk-pin = <2>;
> +               realtek,jd-src = <1>;
> +               realtek,dmic-clk-rate-hz = <2048000>;
> +       };
> +};
> +
> +&lpass_cpu {
> +       status = "okay";
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mi2s0_data0 &mi2s0_data1 &mi2s0_mclk &mi2s0_sclk &mi2s0_ws
> +                    &mi2s1_data0 &mi2s1_sclk &mi2s1_ws>;
> +
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
> +       dai-link@0 {
> +               reg = <MI2S_PRIMARY>;
> +               qcom,playback-sd-lines = <1>;
> +               qcom,capture-sd-lines = <0>;
> +       };
> +
> +       dai-link@1 {
> +               reg = <MI2S_SECONDARY>;
> +               qcom,playback-sd-lines = <0>;
> +       };
> +};
> +
> +&mi2s0_data0 {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_data1 {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_mclk {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_sclk {
> +       drive-strength = <6>;
> +       bias-disable;
> +};
> +
> +&mi2s0_ws {
> +       drive-strength = <6>;

Just like for patch #1, I think you want "bias-disable" here, too.

-Doug

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[v2 3/3] arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1

[Judy Hsiao]

Include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1 as
these boards use rt5682 codec.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts | 1 +
 arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts  | 1 +
 2 files changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
index b69ca09d9bfb..f68d28f8701b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-audio-rt5682.dtsi"
 
 / {
 	model = "Google Herobrine (rev1+)";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
index d3d6ffad4eff..7a4acd3b9ee3 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-audio-rt5682.dtsi"
 
 / {
 	model = "Google Villager (rev0+)";
-- 
2.36.1.124.g0e6072fb45-goog

[v2 3/3] arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1

[Judy Hsiao]

Include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1 as
these boards use rt5682 codec.

Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
---
 arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts | 1 +
 arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts  | 1 +
 2 files changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
index b69ca09d9bfb..f68d28f8701b 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-audio-rt5682.dtsi"
 
 / {
 	model = "Google Herobrine (rev1+)";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
index d3d6ffad4eff..7a4acd3b9ee3 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-audio-rt5682.dtsi"
 
 / {
 	model = "Google Villager (rev0+)";
-- 
2.36.1.124.g0e6072fb45-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 3/3] arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1

[Matthias Kaehlcke]

On Fri, May 20, 2022 at 04:10:04PM +0000, Judy Hsiao wrote:
> Include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1 as
> these boards use rt5682 codec.
> 
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>

Please make sure to collect tags when sending new revisions, you already
had this for v1:

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [v2 3/3] arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1

[Matthias Kaehlcke]

On Fri, May 20, 2022 at 04:10:04PM +0000, Judy Hsiao wrote:
> Include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1 as
> these boards use rt5682 codec.
> 
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>

Please make sure to collect tags when sending new revisions, you already
had this for v1:

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [v2 3/3] arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 9:10 AM Judy Hsiao <judyhsiao@chromium.org> wrote:
>
> Include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1 as
> these boards use rt5682 codec.
>
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts | 1 +
>  arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts  | 1 +
>  2 files changed, 2 insertions(+)

Reviewed-by: Douglas Anderson <dianders@chromium.org>

Re: [v2 3/3] arm64: dts: qcom: sc7280: include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1

[Doug Anderson]

Hi,

On Fri, May 20, 2022 at 9:10 AM Judy Hsiao <judyhsiao@chromium.org> wrote:
>
> Include sc7280-herobrine-audio-rt5682.dtsi in villager and herobrine-r1 as
> these boards use rt5682 codec.
>
> Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
> ---
>  arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts | 1 +
>  arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts  | 1 +
>  2 files changed, 2 insertions(+)

Reviewed-by: Douglas Anderson <dianders@chromium.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel