Re: [PATCH 04/20] migration: rename rate limiting fields in QEMUFile

["Dr. David Alan Gilbert" <dgilbert@redhat.com>]

* Daniel P. Berrangé (berrange@redhat.com) wrote:
> This renames the following QEMUFile fields
> 
>  * bytes_xfer -> rate_limit_used
>  * xfer_limit -> rate_limit_max
> 
> The intent is to make it clear that 'bytes_xfer' is specifically related
> to rate limiting of data and applies to data queued, which need not have
> been transferred on the wire yet if a flush hasn't taken place.
> 
> Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>

Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>


> ---
>  migration/qemu-file.c | 30 +++++++++++++++++++-----------
>  1 file changed, 19 insertions(+), 11 deletions(-)
> 
> diff --git a/migration/qemu-file.c b/migration/qemu-file.c
> index 1479cddad9..03f0b13a55 100644
> --- a/migration/qemu-file.c
> +++ b/migration/qemu-file.c
> @@ -39,8 +39,16 @@ struct QEMUFile {
>      const QEMUFileHooks *hooks;
>      void *opaque;
>  
> -    int64_t bytes_xfer;
> -    int64_t xfer_limit;
> +    /*
> +     * Maximum amount of data in bytes to transfer during one
> +     * rate limiting time window
> +     */
> +    int64_t rate_limit_max;
> +    /*
> +     * Total amount of data in bytes queued for transfer
> +     * during this rate limiting time window
> +     */
> +    int64_t rate_limit_used;
>  
>      int64_t pos; /* start of buffer when writing, end of buffer
>                      when reading */
> @@ -304,7 +312,7 @@ size_t ram_control_save_page(QEMUFile *f, ram_addr_t block_offset,
>          int ret = f->hooks->save_page(f, f->opaque, block_offset,
>                                        offset, size, bytes_sent);
>          if (ret != RAM_SAVE_CONTROL_NOT_SUPP) {
> -            f->bytes_xfer += size;
> +            f->rate_limit_used += size;
>          }
>  
>          if (ret != RAM_SAVE_CONTROL_DELAYED &&
> @@ -457,7 +465,7 @@ void qemu_put_buffer_async(QEMUFile *f, const uint8_t *buf, size_t size,
>          return;
>      }
>  
> -    f->bytes_xfer += size;
> +    f->rate_limit_used += size;
>      add_to_iovec(f, buf, size, may_free);
>  }
>  
> @@ -475,7 +483,7 @@ void qemu_put_buffer(QEMUFile *f, const uint8_t *buf, size_t size)
>              l = size;
>          }
>          memcpy(f->buf + f->buf_index, buf, l);
> -        f->bytes_xfer += l;
> +        f->rate_limit_used += l;
>          add_buf_to_iovec(f, l);
>          if (qemu_file_get_error(f)) {
>              break;
> @@ -492,7 +500,7 @@ void qemu_put_byte(QEMUFile *f, int v)
>      }
>  
>      f->buf[f->buf_index] = v;
> -    f->bytes_xfer++;
> +    f->rate_limit_used++;
>      add_buf_to_iovec(f, 1);
>  }
>  
> @@ -674,7 +682,7 @@ int qemu_file_rate_limit(QEMUFile *f)
>      if (qemu_file_get_error(f)) {
>          return 1;
>      }
> -    if (f->xfer_limit > 0 && f->bytes_xfer > f->xfer_limit) {
> +    if (f->rate_limit_max > 0 && f->rate_limit_used > f->rate_limit_max) {
>          return 1;
>      }
>      return 0;
> @@ -682,22 +690,22 @@ int qemu_file_rate_limit(QEMUFile *f)
>  
>  int64_t qemu_file_get_rate_limit(QEMUFile *f)
>  {
> -    return f->xfer_limit;
> +    return f->rate_limit_max;
>  }
>  
>  void qemu_file_set_rate_limit(QEMUFile *f, int64_t limit)
>  {
> -    f->xfer_limit = limit;
> +    f->rate_limit_max = limit;
>  }
>  
>  void qemu_file_reset_rate_limit(QEMUFile *f)
>  {
> -    f->bytes_xfer = 0;
> +    f->rate_limit_used = 0;
>  }
>  
>  void qemu_file_update_transfer(QEMUFile *f, int64_t len)
>  {
> -    f->bytes_xfer += len;
> +    f->rate_limit_used += len;
>  }
>  
>  void qemu_put_be16(QEMUFile *f, unsigned int v)
> -- 
> 2.36.1
> 
-- 
Dr. David Alan Gilbert / dgilbert@redhat.com / Manchester, UK