[PATCH v7 0/3] PCI: IPQ6018 platform support

[PATCH v7 0/3] PCI: IPQ6018 platform support

[Baruch Siach]

This series adds support for the single PCIe lane on IPQ6018 SoCs. The code is 
ported from downstream Codeaurora v5.4 kernel. The main difference from 
downstream code is the split of PCIe registers configuration from .init to 
.post_init, since it requires phy_power_on().

Tested on IPQ6010 based hardware.

Changes in v7:

  * Use FIELD_PREP for power limit and scale fields

  * Add Stanimir Varbanov to Cc

  * Rebase on v5.19-rc1

Changes in v6:

  * Drop DT patch applied to the qcom tree

  * Normalize driver changes subject line

  * Add a preparatory patch to rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL,
    and define it using PCI_EXP_SLTCAP_* macros

  * Drop a vague comment about ASPM configuration

  * Add a comment about the source of delay periods

Changes in v5:

  * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)

Changes in v4:

  * Drop applied DT bits

  * Add max-link-speed that was missing from the applied v2 patch

  * Rebase the driver on v5.16-rc3

Changes in v3:

  * Drop applied patches

  * Rely on generic code for speed setup

  * Drop unused macros

  * Formatting fixes

Changes in v2:

  * Add patch moving GEN3_RELATED macros to a common header

  * Drop ATU configuration from pcie-qcom

  * Remove local definition of common registers

  * Use bulk clk and reset APIs

  * Remove msi-parent from device-tree

Baruch Siach (2):
  PCI: dwc: tegra: move GEN3_RELATED DBI register to common header
  PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

Selvam Sathappan Periakaruppan (1):
  PCI: qcom: Add IPQ60xx support

 drivers/pci/controller/dwc/pcie-designware.h |   7 +
 drivers/pci/controller/dwc/pcie-qcom.c       | 157 ++++++++++++++++++-
 drivers/pci/controller/dwc/pcie-tegra194.c   |   6 -
 3 files changed, 162 insertions(+), 8 deletions(-)

-- 
2.35.1

[PATCH v7 0/3] PCI: IPQ6018 platform support

[Baruch Siach]

This series adds support for the single PCIe lane on IPQ6018 SoCs. The code is 
ported from downstream Codeaurora v5.4 kernel. The main difference from 
downstream code is the split of PCIe registers configuration from .init to 
.post_init, since it requires phy_power_on().

Tested on IPQ6010 based hardware.

Changes in v7:

  * Use FIELD_PREP for power limit and scale fields

  * Add Stanimir Varbanov to Cc

  * Rebase on v5.19-rc1

Changes in v6:

  * Drop DT patch applied to the qcom tree

  * Normalize driver changes subject line

  * Add a preparatory patch to rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL,
    and define it using PCI_EXP_SLTCAP_* macros

  * Drop a vague comment about ASPM configuration

  * Add a comment about the source of delay periods

Changes in v5:

  * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)

Changes in v4:

  * Drop applied DT bits

  * Add max-link-speed that was missing from the applied v2 patch

  * Rebase the driver on v5.16-rc3

Changes in v3:

  * Drop applied patches

  * Rely on generic code for speed setup

  * Drop unused macros

  * Formatting fixes

Changes in v2:

  * Add patch moving GEN3_RELATED macros to a common header

  * Drop ATU configuration from pcie-qcom

  * Remove local definition of common registers

  * Use bulk clk and reset APIs

  * Remove msi-parent from device-tree

Baruch Siach (2):
  PCI: dwc: tegra: move GEN3_RELATED DBI register to common header
  PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

Selvam Sathappan Periakaruppan (1):
  PCI: qcom: Add IPQ60xx support

 drivers/pci/controller/dwc/pcie-designware.h |   7 +
 drivers/pci/controller/dwc/pcie-qcom.c       | 157 ++++++++++++++++++-
 drivers/pci/controller/dwc/pcie-tegra194.c   |   6 -
 3 files changed, 162 insertions(+), 8 deletions(-)

-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 1/3] PCI: dwc: tegra: move GEN3_RELATED DBI register to common header

[Baruch Siach]

From: Baruch Siach <baruch.siach@siklu.com>

These are common dwc macros that will be used for other platforms.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
---
 drivers/pci/controller/dwc/pcie-designware.h | 6 ++++++
 drivers/pci/controller/dwc/pcie-tegra194.c   | 6 ------
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 7d6e9b7576be..ea87809ee298 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -74,6 +74,12 @@
 #define PCIE_MSI_INTR0_MASK		0x82C
 #define PCIE_MSI_INTR0_STATUS		0x830
 
+#define GEN3_RELATED_OFF			0x890
+#define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL	BIT(0)
+#define GEN3_RELATED_OFF_GEN3_EQ_DISABLE	BIT(16)
+#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT	24
+#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK	GENMASK(25, 24)
+
 #define PCIE_PORT_MULTI_LANE_CTRL	0x8C0
 #define PORT_MLTI_UPCFG_SUPPORT		BIT(7)
 
diff --git a/drivers/pci/controller/dwc/pcie-tegra194.c b/drivers/pci/controller/dwc/pcie-tegra194.c
index cc2678490162..0190786a24b8 100644
--- a/drivers/pci/controller/dwc/pcie-tegra194.c
+++ b/drivers/pci/controller/dwc/pcie-tegra194.c
@@ -191,12 +191,6 @@
 #define GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_MASK	GENMASK(23, 8)
 #define GEN3_EQ_CONTROL_OFF_FB_MODE_MASK	GENMASK(3, 0)
 
-#define GEN3_RELATED_OFF			0x890
-#define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL	BIT(0)
-#define GEN3_RELATED_OFF_GEN3_EQ_DISABLE	BIT(16)
-#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT	24
-#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK	GENMASK(25, 24)
-
 #define PORT_LOGIC_AMBA_ERROR_RESPONSE_DEFAULT	0x8D0
 #define AMBA_ERROR_RESPONSE_CRS_SHIFT		3
 #define AMBA_ERROR_RESPONSE_CRS_MASK		GENMASK(1, 0)
-- 
2.35.1

[PATCH v7 1/3] PCI: dwc: tegra: move GEN3_RELATED DBI register to common header

[Baruch Siach]

From: Baruch Siach <baruch.siach@siklu.com>

These are common dwc macros that will be used for other platforms.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
---
 drivers/pci/controller/dwc/pcie-designware.h | 6 ++++++
 drivers/pci/controller/dwc/pcie-tegra194.c   | 6 ------
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 7d6e9b7576be..ea87809ee298 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -74,6 +74,12 @@
 #define PCIE_MSI_INTR0_MASK		0x82C
 #define PCIE_MSI_INTR0_STATUS		0x830
 
+#define GEN3_RELATED_OFF			0x890
+#define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL	BIT(0)
+#define GEN3_RELATED_OFF_GEN3_EQ_DISABLE	BIT(16)
+#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT	24
+#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK	GENMASK(25, 24)
+
 #define PCIE_PORT_MULTI_LANE_CTRL	0x8C0
 #define PORT_MLTI_UPCFG_SUPPORT		BIT(7)
 
diff --git a/drivers/pci/controller/dwc/pcie-tegra194.c b/drivers/pci/controller/dwc/pcie-tegra194.c
index cc2678490162..0190786a24b8 100644
--- a/drivers/pci/controller/dwc/pcie-tegra194.c
+++ b/drivers/pci/controller/dwc/pcie-tegra194.c
@@ -191,12 +191,6 @@
 #define GEN3_EQ_CONTROL_OFF_PSET_REQ_VEC_MASK	GENMASK(23, 8)
 #define GEN3_EQ_CONTROL_OFF_FB_MODE_MASK	GENMASK(3, 0)
 
-#define GEN3_RELATED_OFF			0x890
-#define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL	BIT(0)
-#define GEN3_RELATED_OFF_GEN3_EQ_DISABLE	BIT(16)
-#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT	24
-#define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK	GENMASK(25, 24)
-
 #define PORT_LOGIC_AMBA_ERROR_RESPONSE_DEFAULT	0x8D0
 #define AMBA_ERROR_RESPONSE_CRS_SHIFT		3
 #define AMBA_ERROR_RESPONSE_CRS_MASK		GENMASK(1, 0)
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 2/3] PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

[Baruch Siach]

From: Baruch Siach <baruch.siach@siklu.com>

The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
describe its meaning.

Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
---
v7:
  Use FIELD_PREP for power limit and stale (Pali Rohár)
---
 drivers/pci/controller/dwc/pcie-qcom.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 2ea13750b492..5ad9be6372f4 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -69,7 +69,20 @@
 #define PCIE20_AXI_MSTR_RESP_COMP_CTRL1		0x81c
 #define CFG_BRIDGE_SB_INIT			BIT(0)
 
-#define PCIE_CAP_LINK1_VAL			0x2FD7F
+#define PCIE_CAP_SLOT_POWER_LIMIT_VAL		FIELD_PREP(PCI_EXP_SLTCAP_SPLV, \
+						250)
+#define PCIE_CAP_SLOT_POWER_LIMIT_SCALE		FIELD_PREP(PCI_EXP_SLTCAP_SPLS, \
+						1)
+#define PCIE_CAP_SLOT_VAL			(PCI_EXP_SLTCAP_ABP | \
+						PCI_EXP_SLTCAP_PCP | \
+						PCI_EXP_SLTCAP_MRLSP | \
+						PCI_EXP_SLTCAP_AIP | \
+						PCI_EXP_SLTCAP_PIP | \
+						PCI_EXP_SLTCAP_HPS | \
+						PCI_EXP_SLTCAP_HPC | \
+						PCI_EXP_SLTCAP_EIP | \
+						PCIE_CAP_SLOT_POWER_LIMIT_VAL | \
+						PCIE_CAP_SLOT_POWER_LIMIT_SCALE)
 
 #define PCIE20_PARF_Q2A_FLUSH			0x1AC
 
@@ -1114,7 +1127,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
 
 	writel(PCI_COMMAND_MASTER, pci->dbi_base + PCI_COMMAND);
 	writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG);
-	writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
+	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
 
 	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
 	val &= ~PCI_EXP_LNKCAP_ASPMS;
-- 
2.35.1

[PATCH v7 2/3] PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

[Baruch Siach]

From: Baruch Siach <baruch.siach@siklu.com>

The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
describe its meaning.

Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
---
v7:
  Use FIELD_PREP for power limit and stale (Pali Rohár)
---
 drivers/pci/controller/dwc/pcie-qcom.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 2ea13750b492..5ad9be6372f4 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -69,7 +69,20 @@
 #define PCIE20_AXI_MSTR_RESP_COMP_CTRL1		0x81c
 #define CFG_BRIDGE_SB_INIT			BIT(0)
 
-#define PCIE_CAP_LINK1_VAL			0x2FD7F
+#define PCIE_CAP_SLOT_POWER_LIMIT_VAL		FIELD_PREP(PCI_EXP_SLTCAP_SPLV, \
+						250)
+#define PCIE_CAP_SLOT_POWER_LIMIT_SCALE		FIELD_PREP(PCI_EXP_SLTCAP_SPLS, \
+						1)
+#define PCIE_CAP_SLOT_VAL			(PCI_EXP_SLTCAP_ABP | \
+						PCI_EXP_SLTCAP_PCP | \
+						PCI_EXP_SLTCAP_MRLSP | \
+						PCI_EXP_SLTCAP_AIP | \
+						PCI_EXP_SLTCAP_PIP | \
+						PCI_EXP_SLTCAP_HPS | \
+						PCI_EXP_SLTCAP_HPC | \
+						PCI_EXP_SLTCAP_EIP | \
+						PCIE_CAP_SLOT_POWER_LIMIT_VAL | \
+						PCIE_CAP_SLOT_POWER_LIMIT_SCALE)
 
 #define PCIE20_PARF_Q2A_FLUSH			0x1AC
 
@@ -1114,7 +1127,7 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
 
 	writel(PCI_COMMAND_MASTER, pci->dbi_base + PCI_COMMAND);
 	writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG);
-	writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
+	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
 
 	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
 	val &= ~PCI_EXP_LNKCAP_ASPMS;
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Baruch Siach]

From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>

IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
platform.

The code is based on downstream[1] Codeaurora kernel v5.4 (branch
win.linuxopenwrt.2.0).

Split out the DBI registers access part from .init into .post_init. DBI
registers are only accessible after phy_power_on().

[1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/

Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
---
v7:

  * Rebase on v5.19-rc1 (Bjorn Helgaas)

v6:

Address Bjorn Helgaas comments:

  * Rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL

  * Drop a vague comment about ASPM configuration

  * Add a comment about the source of delay periods

v5:

  * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)

v4:

  * Rebase on v5.16-rc1

v3:
  * Drop speed setup; rely on generic code (Rob Herring)

  * Drop unused CLK_RATE macros (Bjorn Helgaas)

  * Minor formatting fixes (Bjorn Helgaas)

  * Add reference to downstream Codeaurora kernel tree (Bjorn Helgaas)

v2:
  * Drop ATU configuration; rely on common code instead

  * Use more common register macros

  * Use bulk clk and reset APIs
---
 drivers/pci/controller/dwc/pcie-designware.h |   1 +
 drivers/pci/controller/dwc/pcie-qcom.c       | 140 +++++++++++++++++++
 2 files changed, 141 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index ea87809ee298..279c3778a13b 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -76,6 +76,7 @@
 
 #define GEN3_RELATED_OFF			0x890
 #define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL	BIT(0)
+#define GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS	BIT(13)
 #define GEN3_RELATED_OFF_GEN3_EQ_DISABLE	BIT(16)
 #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT	24
 #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK	GENMASK(25, 24)
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 5ad9be6372f4..acfbfc3d32bd 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -52,6 +52,10 @@
 #define PCIE20_PARF_DBI_BASE_ADDR		0x168
 #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE		0x16C
 #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL	0x174
+#define AHB_CLK_EN				BIT(0)
+#define MSTR_AXI_CLK_EN				BIT(1)
+#define BYPASS					BIT(4)
+
 #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT	0x178
 #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2	0x1A8
 #define PCIE20_PARF_LTSSM			0x1B0
@@ -184,6 +188,11 @@ struct qcom_pcie_resources_2_7_0 {
 	struct clk *ref_clk_src;
 };
 
+struct qcom_pcie_resources_2_9_0 {
+	struct clk_bulk_data clks[5];
+	struct reset_control *rst;
+};
+
 union qcom_pcie_resources {
 	struct qcom_pcie_resources_1_0_0 v1_0_0;
 	struct qcom_pcie_resources_2_1_0 v2_1_0;
@@ -191,6 +200,7 @@ union qcom_pcie_resources {
 	struct qcom_pcie_resources_2_3_3 v2_3_3;
 	struct qcom_pcie_resources_2_4_0 v2_4_0;
 	struct qcom_pcie_resources_2_7_0 v2_7_0;
+	struct qcom_pcie_resources_2_9_0 v2_9_0;
 };
 
 struct qcom_pcie;
@@ -1315,6 +1325,122 @@ static void qcom_pcie_post_deinit_2_7_0(struct qcom_pcie *pcie)
 	clk_disable_unprepare(res->pipe_clk);
 }
 
+static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
+	struct dw_pcie *pci = pcie->pci;
+	struct device *dev = pci->dev;
+	int ret;
+
+	res->clks[0].id = "iface";
+	res->clks[1].id = "axi_m";
+	res->clks[2].id = "axi_s";
+	res->clks[3].id = "axi_bridge";
+	res->clks[4].id = "rchng";
+
+	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
+	if (ret < 0)
+		return ret;
+
+	res->rst = devm_reset_control_array_get_exclusive(dev);
+	if (IS_ERR(res->rst))
+		return PTR_ERR(res->rst);
+
+	return 0;
+}
+
+static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
+
+	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+}
+
+static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
+	struct device *dev = pcie->pci->dev;
+	int ret;
+
+	ret = reset_control_assert(res->rst);
+	if (ret) {
+		dev_err(dev, "reset assert failed (%d)\n", ret);
+		return ret;
+	}
+
+	/*
+	 * Delay periods before and after reset deassert are working values
+	 * from downstream Codeaurora kernel
+	 */
+	usleep_range(2000, 2500);
+
+	ret = reset_control_deassert(res->rst);
+	if (ret) {
+		dev_err(dev, "reset deassert failed (%d)\n", ret);
+		return ret;
+	}
+
+	usleep_range(2000, 2500);
+
+	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	if (ret)
+		goto err_reset;
+
+	return 0;
+
+err_reset:
+	reset_control_assert(res->rst);
+
+	return ret;
+}
+
+static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
+{
+	struct dw_pcie *pci = pcie->pci;
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u32 val;
+	int i;
+
+	writel(SLV_ADDR_SPACE_SZ,
+		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
+
+	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
+	val &= ~BIT(0);
+	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+
+	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
+
+	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
+	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
+		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
+	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
+		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,
+		pci->dbi_base + GEN3_RELATED_OFF);
+
+	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
+		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
+		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
+		pcie->parf + PCIE20_PARF_SYS_CTRL);
+
+	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
+
+	dw_pcie_dbi_ro_wr_en(pci);
+	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
+
+	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
+	val &= ~PCI_EXP_LNKCAP_ASPMS;
+	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
+
+	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
+			PCI_EXP_DEVCTL2);
+
+	for (i = 0; i < 256; i++)
+		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
+				+ (4 * i));
+
+	return 0;
+}
+
 static int qcom_pcie_link_up(struct dw_pcie *pci)
 {
 	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
@@ -1505,6 +1631,15 @@ static const struct qcom_pcie_ops ops_1_9_0 = {
 	.config_sid = qcom_pcie_config_sid_sm8250,
 };
 
+/* Qcom IP rev.: 2.9.0  Synopsys IP rev.: 5.00a */
+static const struct qcom_pcie_ops ops_2_9_0 = {
+	.get_resources = qcom_pcie_get_resources_2_9_0,
+	.init = qcom_pcie_init_2_9_0,
+	.post_init = qcom_pcie_post_init_2_9_0,
+	.deinit = qcom_pcie_deinit_2_9_0,
+	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
+};
+
 static const struct qcom_pcie_cfg apq8084_cfg = {
 	.ops = &ops_1_0_0,
 };
@@ -1569,6 +1704,10 @@ static const struct qcom_pcie_cfg sc8180x_cfg = {
 	.has_tbu_clk = true,
 };
 
+static const struct qcom_pcie_cfg ipq6018_cfg = {
+	.ops = &ops_2_9_0,
+};
+
 static const struct dw_pcie_ops dw_pcie_ops = {
 	.link_up = qcom_pcie_link_up,
 	.start_link = qcom_pcie_start_link,
@@ -1679,6 +1818,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-sm8450-pcie0", .data = &sm8450_pcie0_cfg },
 	{ .compatible = "qcom,pcie-sm8450-pcie1", .data = &sm8450_pcie1_cfg },
 	{ .compatible = "qcom,pcie-sc7280", .data = &sc7280_cfg },
+	{ .compatible = "qcom,pcie-ipq6018", .data = &ipq6018_cfg },
 	{ }
 };
 
-- 
2.35.1

[PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Baruch Siach]

From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>

IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
platform.

The code is based on downstream[1] Codeaurora kernel v5.4 (branch
win.linuxopenwrt.2.0).

Split out the DBI registers access part from .init into .post_init. DBI
registers are only accessible after phy_power_on().

[1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/

Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
---
v7:

  * Rebase on v5.19-rc1 (Bjorn Helgaas)

v6:

Address Bjorn Helgaas comments:

  * Rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL

  * Drop a vague comment about ASPM configuration

  * Add a comment about the source of delay periods

v5:

  * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)

v4:

  * Rebase on v5.16-rc1

v3:
  * Drop speed setup; rely on generic code (Rob Herring)

  * Drop unused CLK_RATE macros (Bjorn Helgaas)

  * Minor formatting fixes (Bjorn Helgaas)

  * Add reference to downstream Codeaurora kernel tree (Bjorn Helgaas)

v2:
  * Drop ATU configuration; rely on common code instead

  * Use more common register macros

  * Use bulk clk and reset APIs
---
 drivers/pci/controller/dwc/pcie-designware.h |   1 +
 drivers/pci/controller/dwc/pcie-qcom.c       | 140 +++++++++++++++++++
 2 files changed, 141 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index ea87809ee298..279c3778a13b 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -76,6 +76,7 @@
 
 #define GEN3_RELATED_OFF			0x890
 #define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL	BIT(0)
+#define GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS	BIT(13)
 #define GEN3_RELATED_OFF_GEN3_EQ_DISABLE	BIT(16)
 #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT	24
 #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK	GENMASK(25, 24)
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 5ad9be6372f4..acfbfc3d32bd 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -52,6 +52,10 @@
 #define PCIE20_PARF_DBI_BASE_ADDR		0x168
 #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE		0x16C
 #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL	0x174
+#define AHB_CLK_EN				BIT(0)
+#define MSTR_AXI_CLK_EN				BIT(1)
+#define BYPASS					BIT(4)
+
 #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT	0x178
 #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2	0x1A8
 #define PCIE20_PARF_LTSSM			0x1B0
@@ -184,6 +188,11 @@ struct qcom_pcie_resources_2_7_0 {
 	struct clk *ref_clk_src;
 };
 
+struct qcom_pcie_resources_2_9_0 {
+	struct clk_bulk_data clks[5];
+	struct reset_control *rst;
+};
+
 union qcom_pcie_resources {
 	struct qcom_pcie_resources_1_0_0 v1_0_0;
 	struct qcom_pcie_resources_2_1_0 v2_1_0;
@@ -191,6 +200,7 @@ union qcom_pcie_resources {
 	struct qcom_pcie_resources_2_3_3 v2_3_3;
 	struct qcom_pcie_resources_2_4_0 v2_4_0;
 	struct qcom_pcie_resources_2_7_0 v2_7_0;
+	struct qcom_pcie_resources_2_9_0 v2_9_0;
 };
 
 struct qcom_pcie;
@@ -1315,6 +1325,122 @@ static void qcom_pcie_post_deinit_2_7_0(struct qcom_pcie *pcie)
 	clk_disable_unprepare(res->pipe_clk);
 }
 
+static int qcom_pcie_get_resources_2_9_0(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
+	struct dw_pcie *pci = pcie->pci;
+	struct device *dev = pci->dev;
+	int ret;
+
+	res->clks[0].id = "iface";
+	res->clks[1].id = "axi_m";
+	res->clks[2].id = "axi_s";
+	res->clks[3].id = "axi_bridge";
+	res->clks[4].id = "rchng";
+
+	ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
+	if (ret < 0)
+		return ret;
+
+	res->rst = devm_reset_control_array_get_exclusive(dev);
+	if (IS_ERR(res->rst))
+		return PTR_ERR(res->rst);
+
+	return 0;
+}
+
+static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
+
+	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
+}
+
+static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
+	struct device *dev = pcie->pci->dev;
+	int ret;
+
+	ret = reset_control_assert(res->rst);
+	if (ret) {
+		dev_err(dev, "reset assert failed (%d)\n", ret);
+		return ret;
+	}
+
+	/*
+	 * Delay periods before and after reset deassert are working values
+	 * from downstream Codeaurora kernel
+	 */
+	usleep_range(2000, 2500);
+
+	ret = reset_control_deassert(res->rst);
+	if (ret) {
+		dev_err(dev, "reset deassert failed (%d)\n", ret);
+		return ret;
+	}
+
+	usleep_range(2000, 2500);
+
+	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
+	if (ret)
+		goto err_reset;
+
+	return 0;
+
+err_reset:
+	reset_control_assert(res->rst);
+
+	return ret;
+}
+
+static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
+{
+	struct dw_pcie *pci = pcie->pci;
+	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	u32 val;
+	int i;
+
+	writel(SLV_ADDR_SPACE_SZ,
+		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
+
+	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
+	val &= ~BIT(0);
+	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+
+	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
+
+	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
+	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
+		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
+	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
+		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,
+		pci->dbi_base + GEN3_RELATED_OFF);
+
+	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
+		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
+		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
+		pcie->parf + PCIE20_PARF_SYS_CTRL);
+
+	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
+
+	dw_pcie_dbi_ro_wr_en(pci);
+	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
+
+	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
+	val &= ~PCI_EXP_LNKCAP_ASPMS;
+	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
+
+	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
+			PCI_EXP_DEVCTL2);
+
+	for (i = 0; i < 256; i++)
+		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
+				+ (4 * i));
+
+	return 0;
+}
+
 static int qcom_pcie_link_up(struct dw_pcie *pci)
 {
 	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
@@ -1505,6 +1631,15 @@ static const struct qcom_pcie_ops ops_1_9_0 = {
 	.config_sid = qcom_pcie_config_sid_sm8250,
 };
 
+/* Qcom IP rev.: 2.9.0  Synopsys IP rev.: 5.00a */
+static const struct qcom_pcie_ops ops_2_9_0 = {
+	.get_resources = qcom_pcie_get_resources_2_9_0,
+	.init = qcom_pcie_init_2_9_0,
+	.post_init = qcom_pcie_post_init_2_9_0,
+	.deinit = qcom_pcie_deinit_2_9_0,
+	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
+};
+
 static const struct qcom_pcie_cfg apq8084_cfg = {
 	.ops = &ops_1_0_0,
 };
@@ -1569,6 +1704,10 @@ static const struct qcom_pcie_cfg sc8180x_cfg = {
 	.has_tbu_clk = true,
 };
 
+static const struct qcom_pcie_cfg ipq6018_cfg = {
+	.ops = &ops_2_9_0,
+};
+
 static const struct dw_pcie_ops dw_pcie_ops = {
 	.link_up = qcom_pcie_link_up,
 	.start_link = qcom_pcie_start_link,
@@ -1679,6 +1818,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-sm8450-pcie0", .data = &sm8450_pcie0_cfg },
 	{ .compatible = "qcom,pcie-sm8450-pcie1", .data = &sm8450_pcie1_cfg },
 	{ .compatible = "qcom,pcie-sc7280", .data = &sc7280_cfg },
+	{ .compatible = "qcom,pcie-ipq6018", .data = &ipq6018_cfg },
 	{ }
 };
 
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 2/3] PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

[Rob Herring]

On Sun, Jun 12, 2022 at 01:18:34PM +0300, Baruch Siach wrote:
> From: Baruch Siach <baruch.siach@siklu.com>
> 
> The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
> PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
> describe its meaning.
> 
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---
> v7:
>   Use FIELD_PREP for power limit and stale (Pali Rohár)
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 17 +++++++++++++++--
>  1 file changed, 15 insertions(+), 2 deletions(-)

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 2/3] PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

[Rob Herring]

On Sun, Jun 12, 2022 at 01:18:34PM +0300, Baruch Siach wrote:
> From: Baruch Siach <baruch.siach@siklu.com>
> 
> The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
> PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
> describe its meaning.
> 
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---
> v7:
>   Use FIELD_PREP for power limit and stale (Pali Rohár)
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 17 +++++++++++++++--
>  1 file changed, 15 insertions(+), 2 deletions(-)

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Rob Herring]

On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---
> v7:
> 
>   * Rebase on v5.19-rc1 (Bjorn Helgaas)
> 
> v6:
> 
> Address Bjorn Helgaas comments:
> 
>   * Rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL
> 
>   * Drop a vague comment about ASPM configuration
> 
>   * Add a comment about the source of delay periods
> 
> v5:
> 
>   * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)
> 
> v4:
> 
>   * Rebase on v5.16-rc1
> 
> v3:
>   * Drop speed setup; rely on generic code (Rob Herring)
> 
>   * Drop unused CLK_RATE macros (Bjorn Helgaas)
> 
>   * Minor formatting fixes (Bjorn Helgaas)
> 
>   * Add reference to downstream Codeaurora kernel tree (Bjorn Helgaas)
> 
> v2:
>   * Drop ATU configuration; rely on common code instead
> 
>   * Use more common register macros
> 
>   * Use bulk clk and reset APIs
> ---
>  drivers/pci/controller/dwc/pcie-designware.h |   1 +
>  drivers/pci/controller/dwc/pcie-qcom.c       | 140 +++++++++++++++++++
>  2 files changed, 141 insertions(+)

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Rob Herring]

On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---
> v7:
> 
>   * Rebase on v5.19-rc1 (Bjorn Helgaas)
> 
> v6:
> 
> Address Bjorn Helgaas comments:
> 
>   * Rename PCIE_CAP_LINK1_VAL to PCIE_CAP_SLOT_VAL
> 
>   * Drop a vague comment about ASPM configuration
> 
>   * Add a comment about the source of delay periods
> 
> v5:
> 
>   * Remove comments from qcom_pcie_init_2_9_0() (Bjorn Andersson)
> 
> v4:
> 
>   * Rebase on v5.16-rc1
> 
> v3:
>   * Drop speed setup; rely on generic code (Rob Herring)
> 
>   * Drop unused CLK_RATE macros (Bjorn Helgaas)
> 
>   * Minor formatting fixes (Bjorn Helgaas)
> 
>   * Add reference to downstream Codeaurora kernel tree (Bjorn Helgaas)
> 
> v2:
>   * Drop ATU configuration; rely on common code instead
> 
>   * Use more common register macros
> 
>   * Use bulk clk and reset APIs
> ---
>  drivers/pci/controller/dwc/pcie-designware.h |   1 +
>  drivers/pci/controller/dwc/pcie-qcom.c       | 140 +++++++++++++++++++
>  2 files changed, 141 insertions(+)

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Stanimir Varbanov]

Hi,

Thanks for the patch!

On 6/12/22 13:18, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>

Looks good:

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>


-- 
regards,
Stan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Stanimir Varbanov]

Hi,

Thanks for the patch!

On 6/12/22 13:18, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>

Looks good:

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>


-- 
regards,
Stan

Re: [PATCH v7 2/3] PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

[Stanimir Varbanov]

On 6/12/22 13:18, Baruch Siach wrote:
> From: Baruch Siach <baruch.siach@siklu.com>
> 
> The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
> PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
> describe its meaning.
> 
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---
> v7:
>   Use FIELD_PREP for power limit and stale (Pali Rohár)
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 17 +++++++++++++++--
>  1 file changed, 15 insertions(+), 2 deletions(-)

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>

-- 
regards,
Stan

Re: [PATCH v7 2/3] PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*

[Stanimir Varbanov]

On 6/12/22 13:18, Baruch Siach wrote:
> From: Baruch Siach <baruch.siach@siklu.com>
> 
> The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
> PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
> describe its meaning.
> 
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---
> v7:
>   Use FIELD_PREP for power limit and stale (Pali Rohár)
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 17 +++++++++++++++--
>  1 file changed, 15 insertions(+), 2 deletions(-)

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>

-- 
regards,
Stan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Johan Hovold]

On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---

> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +
> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);

Assert reset as you do in the init error path?

> +}
> +
> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +	struct device *dev = pcie->pci->dev;
> +	int ret;
> +
> +	ret = reset_control_assert(res->rst);
> +	if (ret) {
> +		dev_err(dev, "reset assert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	/*
> +	 * Delay periods before and after reset deassert are working values
> +	 * from downstream Codeaurora kernel
> +	 */
> +	usleep_range(2000, 2500);
> +
> +	ret = reset_control_deassert(res->rst);
> +	if (ret) {
> +		dev_err(dev, "reset deassert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	usleep_range(2000, 2500);
> +
> +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	if (ret)
> +		goto err_reset;
> +
> +	return 0;
> +
> +err_reset:
> +	reset_control_assert(res->rst);
> +
> +	return ret;
> +}
> +
> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct dw_pcie *pci = pcie->pci;
> +	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> +	u32 val;
> +	int i;
> +
> +	writel(SLV_ADDR_SPACE_SZ,
> +		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
> +
> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> +	val &= ~BIT(0);
> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> +
> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
> +	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
> +		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
> +		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,

I noticed that some of this probably has been copied from from
qcom_pcie_init_2_3_3(), but please move the | operator to the previous
line.

> +		pci->dbi_base + GEN3_RELATED_OFF);
> +
> +	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
> +		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |

Same here.

> +		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
> +		pcie->parf + PCIE20_PARF_SYS_CTRL);
> +
> +	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
> +
> +	dw_pcie_dbi_ro_wr_en(pci);
> +	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
> +
> +	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +	val &= ~PCI_EXP_LNKCAP_ASPMS;
> +	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +
> +	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
> +			PCI_EXP_DEVCTL2);
> +
> +	for (i = 0; i < 256; i++)
> +		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
> +				+ (4 * i));

And here for +, but you should probably just remove the line break (you
can go up to 100 chars if it makes the code more readable).

Please drop the 0x prefix too.

> +
> +	return 0;
> +}

Johan

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Johan Hovold]

On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> ---

> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +
> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);

Assert reset as you do in the init error path?

> +}
> +
> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +	struct device *dev = pcie->pci->dev;
> +	int ret;
> +
> +	ret = reset_control_assert(res->rst);
> +	if (ret) {
> +		dev_err(dev, "reset assert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	/*
> +	 * Delay periods before and after reset deassert are working values
> +	 * from downstream Codeaurora kernel
> +	 */
> +	usleep_range(2000, 2500);
> +
> +	ret = reset_control_deassert(res->rst);
> +	if (ret) {
> +		dev_err(dev, "reset deassert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	usleep_range(2000, 2500);
> +
> +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	if (ret)
> +		goto err_reset;
> +
> +	return 0;
> +
> +err_reset:
> +	reset_control_assert(res->rst);
> +
> +	return ret;
> +}
> +
> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct dw_pcie *pci = pcie->pci;
> +	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> +	u32 val;
> +	int i;
> +
> +	writel(SLV_ADDR_SPACE_SZ,
> +		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
> +
> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> +	val &= ~BIT(0);
> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> +
> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
> +	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
> +		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
> +		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,

I noticed that some of this probably has been copied from from
qcom_pcie_init_2_3_3(), but please move the | operator to the previous
line.

> +		pci->dbi_base + GEN3_RELATED_OFF);
> +
> +	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
> +		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |

Same here.

> +		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
> +		pcie->parf + PCIE20_PARF_SYS_CTRL);
> +
> +	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
> +
> +	dw_pcie_dbi_ro_wr_en(pci);
> +	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
> +
> +	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +	val &= ~PCI_EXP_LNKCAP_ASPMS;
> +	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +
> +	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
> +			PCI_EXP_DEVCTL2);
> +
> +	for (i = 0; i < 256; i++)
> +		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
> +				+ (4 * i));

And here for +, but you should probably just remove the line break (you
can go up to 100 chars if it makes the code more readable).

Please drop the 0x prefix too.

> +
> +	return 0;
> +}

Johan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Baruch Siach]

Hi Johan,

Thanks for your review comments.

On Mon, Jun 20 2022, Johan Hovold wrote:
> On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
>> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
>> 
>> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
>> platform.
>> 
>> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
>> win.linuxopenwrt.2.0).
>> 
>> Split out the DBI registers access part from .init into .post_init. DBI
>> registers are only accessible after phy_power_on().
>> 
>> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
>> 
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
>> ---
>
>> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
>> +
>> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
>
> Assert reset as you do in the init error path?

Not sure about that. As I understand, the reset assert/deassert sequence
on init is meant to ensure clean startup state. Deinit most likely does
not need that. So maybe I should remove reset assert from init error
path instead?

As always, this code sequence is from downstream kernel. I have no
access to documentation.

baruch

>> +}
>> +
>> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
>> +	struct device *dev = pcie->pci->dev;
>> +	int ret;
>> +
>> +	ret = reset_control_assert(res->rst);
>> +	if (ret) {
>> +		dev_err(dev, "reset assert failed (%d)\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	/*
>> +	 * Delay periods before and after reset deassert are working values
>> +	 * from downstream Codeaurora kernel
>> +	 */
>> +	usleep_range(2000, 2500);
>> +
>> +	ret = reset_control_deassert(res->rst);
>> +	if (ret) {
>> +		dev_err(dev, "reset deassert failed (%d)\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	usleep_range(2000, 2500);
>> +
>> +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
>> +	if (ret)
>> +		goto err_reset;
>> +
>> +	return 0;
>> +
>> +err_reset:
>> +	reset_control_assert(res->rst);
>> +
>> +	return ret;
>> +}
>> +
>> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct dw_pcie *pci = pcie->pci;
>> +	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>> +	u32 val;
>> +	int i;
>> +
>> +	writel(SLV_ADDR_SPACE_SZ,
>> +		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
>> +
>> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +	val &= ~BIT(0);
>> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +
>> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
>> +
>> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
>> +	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
>> +		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
>> +	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
>> +		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,
>
> I noticed that some of this probably has been copied from from
> qcom_pcie_init_2_3_3(), but please move the | operator to the previous
> line.
>
>> +		pci->dbi_base + GEN3_RELATED_OFF);
>> +
>> +	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
>> +		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
>
> Same here.
>
>> +		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
>> +		pcie->parf + PCIE20_PARF_SYS_CTRL);
>> +
>> +	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
>> +
>> +	dw_pcie_dbi_ro_wr_en(pci);
>> +	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>> +
>> +	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +	val &= ~PCI_EXP_LNKCAP_ASPMS;
>> +	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +
>> +	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
>> +			PCI_EXP_DEVCTL2);
>> +
>> +	for (i = 0; i < 256; i++)
>> +		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
>> +				+ (4 * i));
>
> And here for +, but you should probably just remove the line break (you
> can go up to 100 chars if it makes the code more readable).
>
> Please drop the 0x prefix too.
>
>> +
>> +	return 0;
>> +}
>
> Johan


-- 
                                                     ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Baruch Siach]

Hi Johan,

Thanks for your review comments.

On Mon, Jun 20 2022, Johan Hovold wrote:
> On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
>> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
>> 
>> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
>> platform.
>> 
>> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
>> win.linuxopenwrt.2.0).
>> 
>> Split out the DBI registers access part from .init into .post_init. DBI
>> registers are only accessible after phy_power_on().
>> 
>> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
>> 
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
>> ---
>
>> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
>> +
>> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
>
> Assert reset as you do in the init error path?

Not sure about that. As I understand, the reset assert/deassert sequence
on init is meant to ensure clean startup state. Deinit most likely does
not need that. So maybe I should remove reset assert from init error
path instead?

As always, this code sequence is from downstream kernel. I have no
access to documentation.

baruch

>> +}
>> +
>> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
>> +	struct device *dev = pcie->pci->dev;
>> +	int ret;
>> +
>> +	ret = reset_control_assert(res->rst);
>> +	if (ret) {
>> +		dev_err(dev, "reset assert failed (%d)\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	/*
>> +	 * Delay periods before and after reset deassert are working values
>> +	 * from downstream Codeaurora kernel
>> +	 */
>> +	usleep_range(2000, 2500);
>> +
>> +	ret = reset_control_deassert(res->rst);
>> +	if (ret) {
>> +		dev_err(dev, "reset deassert failed (%d)\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	usleep_range(2000, 2500);
>> +
>> +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
>> +	if (ret)
>> +		goto err_reset;
>> +
>> +	return 0;
>> +
>> +err_reset:
>> +	reset_control_assert(res->rst);
>> +
>> +	return ret;
>> +}
>> +
>> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> +	struct dw_pcie *pci = pcie->pci;
>> +	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>> +	u32 val;
>> +	int i;
>> +
>> +	writel(SLV_ADDR_SPACE_SZ,
>> +		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
>> +
>> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +	val &= ~BIT(0);
>> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +
>> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
>> +
>> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
>> +	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
>> +		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
>> +	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
>> +		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,
>
> I noticed that some of this probably has been copied from from
> qcom_pcie_init_2_3_3(), but please move the | operator to the previous
> line.
>
>> +		pci->dbi_base + GEN3_RELATED_OFF);
>> +
>> +	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
>> +		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
>
> Same here.
>
>> +		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
>> +		pcie->parf + PCIE20_PARF_SYS_CTRL);
>> +
>> +	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
>> +
>> +	dw_pcie_dbi_ro_wr_en(pci);
>> +	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>> +
>> +	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +	val &= ~PCI_EXP_LNKCAP_ASPMS;
>> +	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +
>> +	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
>> +			PCI_EXP_DEVCTL2);
>> +
>> +	for (i = 0; i < 256; i++)
>> +		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
>> +				+ (4 * i));
>
> And here for +, but you should probably just remove the line break (you
> can go up to 100 chars if it makes the code more readable).
>
> Please drop the 0x prefix too.
>
>> +
>> +	return 0;
>> +}
>
> Johan


-- 
                                                     ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Johan Hovold]

On Tue, Jun 21, 2022 at 06:39:45AM +0300, Baruch Siach wrote:
> Hi Johan,
> 
> Thanks for your review comments.
> 
> On Mon, Jun 20 2022, Johan Hovold wrote:
> > On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> >> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> >> 
> >> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> >> platform.
> >> 
> >> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> >> win.linuxopenwrt.2.0).
> >> 
> >> Split out the DBI registers access part from .init into .post_init. DBI
> >> registers are only accessible after phy_power_on().
> >> 
> >> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> >> 
> >> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> >> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> >> ---
> >
> >> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> >> +{
> >> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> >> +
> >> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> >
> > Assert reset as you do in the init error path?
> 
> Not sure about that. As I understand, the reset assert/deassert sequence
> on init is meant to ensure clean startup state. Deinit most likely does
> not need that. So maybe I should remove reset assert from init error
> path instead?

Yeah, I think the init error path and deinit should at least be
consistent.

> As always, this code sequence is from downstream kernel. I have no
> access to documentation.

I feel your pain. ;)

Johan

Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Johan Hovold]

On Tue, Jun 21, 2022 at 06:39:45AM +0300, Baruch Siach wrote:
> Hi Johan,
> 
> Thanks for your review comments.
> 
> On Mon, Jun 20 2022, Johan Hovold wrote:
> > On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> >> From: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
> >> 
> >> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> >> platform.
> >> 
> >> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> >> win.linuxopenwrt.2.0).
> >> 
> >> Split out the DBI registers access part from .init into .post_init. DBI
> >> registers are only accessible after phy_power_on().
> >> 
> >> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> >> 
> >> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
> >> Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
> >> ---
> >
> >> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> >> +{
> >> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> >> +
> >> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
> >
> > Assert reset as you do in the init error path?
> 
> Not sure about that. As I understand, the reset assert/deassert sequence
> on init is meant to ensure clean startup state. Deinit most likely does
> not need that. So maybe I should remove reset assert from init error
> path instead?

Yeah, I think the init error path and deinit should at least be
consistent.

> As always, this code sequence is from downstream kernel. I have no
> access to documentation.

I feel your pain. ;)

Johan

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel