From: Shazad Hussain <quic_shazhuss@quicinc.com>
To: Parikshit Pareek <quic_ppareek@quicinc.com>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Rob Herring <robh+dt@kernel.org>,
"Krzysztof Kozlowski" <krzysztof.kozlowski+dt@linaro.org>
Cc: <linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Andrew Halaney <ahalaney@redhat.com>,
"Brian Masney" <bmasney@redhat.com>,
Johan Hovold <johan@kernel.org>
Subject: Re: [PATCH v6 2/2] arm64: dts: qcom: add SA8540P ride(Qdrive-3)
Date: Wed, 2 Nov 2022 13:05:37 +0530 [thread overview]
Message-ID: <a1ce89bf-78b3-4fdf-e9ba-befa55482bb4@quicinc.com> (raw)
In-Reply-To: <20221020073036.16656-3-quic_ppareek@quicinc.com>
On 10/20/2022 1:00 PM, Parikshit Pareek wrote:
> Introduce the Qualcomm SA8540P ride automotive platform, also known as
> Qdrive-3 development board.
>
> This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> regulators, debug UART, PMICs, remoteprocs and USB.
>
> The SA8540P ride contains four PM8450 PMICs.
>
> Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 309 ++++++++++++++++++++++
> 2 files changed, 310 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index b0558d3389e5..c89d44756791 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -54,6 +54,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sa8540p-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> new file mode 100644
> index 000000000000..0faf06625b05
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -0,0 +1,309 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +#include "sa8540p.dtsi"
> +
> +/ {
> + model = "Qualcomm SA8540P Ride";
> + compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
> +
> + aliases {
> + serial0 = &qup2_uart17;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +&apps_rsc {
> + pmm8540-a-regulators {
> + compatible = "qcom,pm8150-rpmh-regulators";
> + qcom,pmic-id = "a";
> +
> + vreg_l3a: ldo3 {
> + regulator-name = "vreg_l3a";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1208000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5a: ldo5 {
> + regulator-name = "vreg_l5a";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7a: ldo7 {
> + regulator-name = "vreg_l7a";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13a: ldo13 {
> + regulator-name = "vreg_l13a";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + pmm8540-c-regulators {
> + compatible = "qcom,pm8150-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vreg_l1c: ldo1 {
> + regulator-name = "vreg_l1c";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2c: ldo2 {
> + regulator-name = "vreg_l2c";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3c: ldo3 {
> + regulator-name = "vreg_l3c";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
As we don't have ufs_card_hc for ride platform, we can remove vreg_l3c.
> +
> + vreg_l4c: ldo4 {
> + regulator-name = "vreg_l4c";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1208000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6c: ldo6 {
> + regulator-name = "vreg_l6c";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> +
> + vreg_l7c: ldo7 {
> + regulator-name = "vreg_l7c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10c: ldo10 {
> + regulator-name = "vreg_l10c";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
Similarly we can remove this vreg_l10c.
> +
> + vreg_l17c: ldo17 {
> + regulator-name = "vreg_l17c";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + };
> + };
> +
> + pmm8540-g-regulators {
> + compatible = "qcom,pm8150-rpmh-regulators";
> + qcom,pmic-id = "g";
> +
> + vreg_l3g: ldo3 {
> + regulator-name = "vreg_l3g";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7g: ldo7 {
> + regulator-name = "vreg_l7g";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8g: ldo8 {
> + regulator-name = "vreg_l8g";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&qup2 {
> + status = "okay";
> +};
> +
> +&qup2_uart17 {
> + compatible = "qcom,geni-debug-uart";
> + status = "okay";
> +};
> +
> +&remoteproc_adsp {
> + firmware-name = "qcom/sa8540p/adsp.mbn";
> + status = "okay";
> +};
> +
> +&remoteproc_nsp0 {
> + firmware-name = "qcom/sa8540p/cdsp.mbn";
> + status = "okay";
> +};
> +
> +&remoteproc_nsp1 {
> + firmware-name = "qcom/sa8540p/cdsp1.mbn";
> + status = "okay";
> +};
> +
> +&spmi_bus {
> + pm8450a: pmic@0 {
> + compatible = "qcom,pm8150", "qcom,spmi-pmic";
> + reg = <0x0 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8450a_gpios: gpio@c000 {
> + compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + gpio-ranges = <&pm8450a_gpios 0 0 10>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pm8450c: pmic@4 {
> + compatible = "qcom,pm8150", "qcom,spmi-pmic";
> + reg = <0x4 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8450c_gpios: gpio@c000 {
> + compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + gpio-ranges = <&pm8450c_gpios 0 0 10>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pm8450e: pmic@8 {
> + compatible = "qcom,pm8150", "qcom,spmi-pmic";
> + reg = <0x8 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8450e_gpios: gpio@c000 {
> + compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + gpio-ranges = <&pm8450e_gpios 0 0 10>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + pm8450g: pmic@c {
> + compatible = "qcom,pm8150", "qcom,spmi-pmic";
> + reg = <0xc SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8450g_gpios: gpio@c000 {
> + compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + gpio-ranges = <&pm8450g_gpios 0 0 10>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l17c>;
> + vcc-max-microamp = <800000>;
> + vccq-supply = <&vreg_l6c>;
> + vccq-max-microamp = <900000>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l8g>;
> + vdda-pll-supply = <&vreg_l3g>;
> +
> + status = "okay";
> +};
> +
> +&usb_0 {
> + status = "okay";
> +};
> +
> +&usb_0_dwc3 {
> + /* TODO: Define USB-C connector properly */
> + dr_mode = "peripheral";
> +};
> +
> +&usb_0_hsphy {
> + vdda-pll-supply = <&vreg_l5a>;
> + vdda18-supply = <&vreg_l7a>;
> + vdda33-supply = <&vreg_l13a>;
> +
> + status = "okay";
> +};
> +
> +&usb_0_qmpphy {
> + vdda-phy-supply = <&vreg_l3a>;
> + vdda-pll-supply = <&vreg_l5a>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_hsphy0 {
> + vdda-pll-supply = <&vreg_l5a>;
> + vdda18-supply = <&vreg_l7g>;
> + vdda33-supply = <&vreg_l13a>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_qmpphy0 {
> + vdda-phy-supply = <&vreg_l3a>;
> + vdda-pll-supply = <&vreg_l5a>;
> +
> + status = "okay";
> +};
> +
> +&xo_board_clk {
> + clock-frequency = <38400000>;
> +};
> +
> +/* PINCTRL */
prev parent reply other threads:[~2022-11-02 7:35 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-20 7:30 [PATCH v6 0/2] arm64: dts: qcom: add dts for sa8540p-ride board Parikshit Pareek
2022-10-20 7:30 ` [PATCH v6 1/2] dt-bindings: arm: qcom: Document additional sa8540p device Parikshit Pareek
2022-10-20 13:46 ` Krzysztof Kozlowski
2022-10-20 16:33 ` Brian Masney
2022-10-20 7:30 ` [PATCH v6 2/2] arm64: dts: qcom: add SA8540P ride(Qdrive-3) Parikshit Pareek
2022-10-20 11:49 ` konrad.dybcio
2022-10-28 7:50 ` Parikshit Pareek
2022-10-28 8:28 ` Brian Masney
2022-10-20 16:39 ` Brian Masney
2022-11-02 7:35 ` Shazad Hussain [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a1ce89bf-78b3-4fdf-e9ba-befa55482bb4@quicinc.com \
--to=quic_shazhuss@quicinc.com \
--cc=agross@kernel.org \
--cc=ahalaney@redhat.com \
--cc=andersson@kernel.org \
--cc=bmasney@redhat.com \
--cc=devicetree@vger.kernel.org \
--cc=johan@kernel.org \
--cc=konrad.dybcio@somainline.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=quic_ppareek@quicinc.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.